Wu Zhangjin [Mon, 4 Jan 2010 09:16:48 +0000 (17:16 +0800)]
MIPS: Loongson: Cleanup of the environment variables
Changes:
o Move bus_clock into prom_init_env()
o Initialize the cpu_clock_freq to the default values for the
correspoding processor revisions if no such environment variable
passed by BIOS/Bootloader.
Wu Zhangjin [Mon, 4 Jan 2010 09:16:46 +0000 (17:16 +0800)]
MIPS: Loongson: Remove the serial port output of compressed kernel support
The compressed kernel support on loongson family machines is stable now,
so, remove the debug information via using SYS_SUPPORTS_ZBOOT instead of
SYS_SUPPORTS_ZBOOT_UART16550. This may reduce the image size and speedup
the booting.
Wu Zhangjin [Mon, 4 Jan 2010 09:16:43 +0000 (17:16 +0800)]
MIPS: Loongson: Lemote-2F: Get the machine type from PMON_VER
Lemote have used the PMON_VER strings to indicate the loongson-2f
machine series:
PMON_VER=LM8089 Lemote 8.9'' netbook
LM8101 Lemote 10.1'' netbook
(The above two netbooks have the same kernel support)
LM6XXX Lemote FuLoong(2F) box series
LM9XXX Lemote LynLoong PC series
Before the machtype is supported by the PMON, we can get the machine
type from the PMON_VER for these machines, this will help the users a
lot.
David Daney [Thu, 7 Jan 2010 19:05:06 +0000 (11:05 -0800)]
Staging: Octeon Ethernet: Use constants from in.h
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
To: gregkh@suse.de
Patchwork: http://patchwork.linux-mips.org/patch/837/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Thu, 7 Jan 2010 19:05:05 +0000 (11:05 -0800)]
Staging: Octeon Ethernet: Enable scatter-gather.
Octeon ethernet hardware can handle NETIF_F_SG, so we enable it.
A gather list of up to six fragments will fit in the SKB's CB
structure, so no extra memory is required. If a SKB has more than six
fragments, we must linearize it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
To: gregkh@suse.de
Patchwork: http://patchwork.linux-mips.org/patch/838/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Thu, 7 Jan 2010 19:05:04 +0000 (11:05 -0800)]
Staging: Octeon Ethernet: Convert to NAPI.
Convert the driver to be a reasonably well behaved NAPI citizen.
There is one NAPI instance per CPU shared between all input ports. As
receive backlog increases, NAPI is scheduled on additional CPUs.
Receive buffer refill code factored out so it can also be called from
the periodic timer. This is needed to recover from temporary buffer
starvation conditions.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
To: gregkh@suse.de
Patchwork: http://patchwork.linux-mips.org/patch/839/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Thu, 7 Jan 2010 19:05:03 +0000 (11:05 -0800)]
Staging: Octeon Ethernet: Rewrite transmit code.
Stop the queue if too many packets are queued. Restart it from a high
resolution timer.
Rearrange and simplify locking and SKB freeing code
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
To: gregkh@suse.de
Patchwork: http://patchwork.linux-mips.org/patch/843/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Thu, 7 Jan 2010 19:05:01 +0000 (11:05 -0800)]
Staging: Octeon Ethernet: Remove unused code.
Remove unused code, reindent, and join some spilt strings.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
To: gregkh@suse.de
Patchwork: http://patchwork.linux-mips.org/patch/842/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Thu, 7 Jan 2010 19:05:00 +0000 (11:05 -0800)]
MIPS: Octeon: Fix EOI handling.
If an interrupt handler disables interrupts, the EOI function will
just reenable them. This will put us in an endless loop when the
upcoming Ethernet driver patches are applied.
Only reenable the interrupt on EOI if it is not IRQ_DISABLED. This
requires that the EOI function be separate from the ENABLE function.
We also rename the ACK functions to correspond with their function.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
To: gregkh@suse.de
Patchwork: http://patchwork.linux-mips.org/patch/840/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Sat, 9 Jan 2010 01:17:44 +0000 (17:17 -0800)]
MIPS: Octeon: Use optimized memory barrier primitives.
In order to achieve correct synchronization semantics, the Octeon port
had defined CONFIG_WEAK_REORDERING_BEYOND_LLSC. This resulted in code
that looks like:
sync
ll ...
.
.
.
sc ...
.
.
sync
The second SYNC was redundant, but harmless.
Octeon has a SYNCW instruction that acts as a write-memory-barrier
(due to an erratum in some parts two SYNCW are used). It is much
faster than SYNC because it imposes ordering on the writes, but
doesn't otherwise stall the execution pipeline. On Octeon, SYNC
stalls execution until all preceeding writes are committed to the
coherent memory system.
Using:
syncw;syncw
ll
.
.
.
sc
.
.
Has identical semantics to the first sequence, but is much faster.
The SYNCW orders the writes, and the SC will not complete successfully
until the write is committed to the coherent memory system. So at the
end all preceeding writes have been committed. Since Octeon does not
do speculative reads, this functions as a full barrier.
The patch removes CONFIG_WEAK_REORDERING_BEYOND_LLSC, and substitutes
SYNCW for SYNC in write-memory-barriers.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/850/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Sat, 9 Jan 2010 01:17:43 +0000 (17:17 -0800)]
MIPS: New macro smp_mb__before_llsc.
Replace some instances of smp_llsc_mb() with a new macro
smp_mb__before_llsc(). It is used before ll/sc sequences that are
documented as needing write barrier semantics.
The default implementation of smp_mb__before_llsc() is just smp_llsc_mb(),
so there are no changes in semantics.
Also simplify definition of smp_mb(), smp_rmb(), and smp_wmb() to be just
barrier() in the non-SMP case.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/851/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Thu, 7 Jan 2010 19:54:21 +0000 (11:54 -0800)]
MIPS: Octeon: Register some devices on the I2C bus.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
To: linux-i2c@vger.kernel.org
To: ben-linux@fluff.org
To: khali@linux-fr.org Cc: Rade Bozic <rade.bozic.ext@nsn.com>
Patchwork: http://patchwork.linux-mips.org/patch/845/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Rade Bozic [Thu, 28 Jan 2010 20:47:07 +0000 (12:47 -0800)]
MIPS: I2C: Add driver for Cavium OCTEON I2C ports.
Signed-off-by: Rade Bozic <rade.bozic.ext@nsn.com> Signed-off-by: David Daney <ddaney@caviumnetworks.com> Cc: Michael Lawnick <michael.lawnick.ext@nsn.com>
To: linux-mips@linux-mips.org
To: linux-i2c@vger.kernel.org
To: ben-linux@fluff.org
To: khali@linux-fr.org Cc: rade.bozic.ext@nsn.com Cc: Michael Lawnick <michael.lawnick.ext@nsn.com>
Patchwork: http://patchwork.linux-mips.org/patch/890/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Thu, 7 Jan 2010 21:23:41 +0000 (13:23 -0800)]
MIPS: Octeon: Add I2C platform device.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
To: linux-i2c@vger.kernel.org
To: ben-linux@fluff.org
To: khali@linux-fr.org Cc: Rade Bozic <rade.bozic.ext@nsn.com>
Patchwork: http://patchwork.linux-mips.org/patch/847/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Robert P. J. Day [Thu, 31 Dec 2009 20:39:00 +0000 (15:39 -0500)]
MIPS: Simplify param.h by using <asm-generic/param.h>
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/810/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss [Tue, 8 Dec 2009 18:18:13 +0000 (19:18 +0100)]
MIPS: Alchemy: get rid of common/reset.c
Implement reset / poweroff in the board code instead. The peripheral reset
code is gone too since YAMON which all in-tree boards use does the same
work when it boots.
David Daney [Fri, 4 Dec 2009 21:52:36 +0000 (13:52 -0800)]
MIPS: Two-level pagetables for 64-bit kernels with 64KB pages.
For 64-bit kernels with 64KB pages and two level page tables, there are
42 bits worth of virtual address space This is larger than the 40 bits of
virtual address space obtained with the default 4KB Page size and three
levels, so there are no draw backs for using two level tables with this
configuration.
Manuel Lauss [Mon, 23 Nov 2009 19:40:00 +0000 (20:40 +0100)]
MIPS: Alchemy: use runtime cpu detection in GPIO code.
Remove the cpu subtype cpp macros in favor of runtime detection,
to improve compile coverage of the alchemy common code.
(Increases kernel size by 700 bytes).
Florian Fainelli [Tue, 10 Nov 2009 00:13:38 +0000 (01:13 +0100)]
NET: au1000-eth: Convert to platform_driver model
This patch converts the au1000-eth driver to become a full platform-driver
as it ought to be. We now pass PHY-speficic configurations through
platform_data but for compatibility the driver still assumes the default
settings (search for PHY1 on MAC0) when no platform_data is passed. Tested
on my MTX-1 board.
Signed-off-by: Florian Fainelli <florian@openwrt.org> Cc: linux-mips@linux-mips.org Cc: netdev@vger.kernel.org Acked-by: David S. Miller <davem@davemloft.net>
Patchwork: http://patchwork.linux-mips.org/patch/619/
Patchwork: http://patchwork.linux-mips.org/patch/963/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Florian Fainelli [Tue, 10 Nov 2009 00:13:30 +0000 (01:13 +0100)]
MIPS: Alchemy: Add au1000-eth platform device
This patch makes the board code register the au1000-eth platform device. The
au1000-eth platform data can be overriden with the au1xxx_override_eth_cfg
function like it has to be done for the Bosporus board which uses a
different MAC/PHY setup.
Signed-off-by: Florian Fainelli <florian@openwrt.org> Cc: David Miller <davem@davemloft.net> Cc: linux-mips@linux-mips.org Cc: netdev@vger.kernel.org
Patchwork: http://patchwork.linux-mips.org/patch/618/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Machine driver for DB1200 AC97 and I2S audio systems, intended as a proper
reference asoc machine for Alchemy-based systems. AC97/I2S can be selected
at boot time by setting switch S6.7.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Cc: Linux-MIPS <linux-mips@linux-mips.org> Cc: alsa-devel@alsa-project.org Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss [Mon, 2 Nov 2009 20:21:43 +0000 (21:21 +0100)]
MIPS: Alchemy: Extended DB1200 board support.
Create own directory for DB1200 code and update it with new features.
- SPI support:
- tmp121 temperature sensor
- SPI flash on DB1200
- I2C support
- NE1619 sensor
- AT24 eeprom
- I2C/SPI can be selected at boot time via switch S6.8
- Carddetect IRQs for SD cards.
- gen_nand based NAND support.
- hexleds count sleep/wake transitions.
Manuel Lauss [Mon, 19 Oct 2009 10:53:37 +0000 (12:53 +0200)]
MIPS: Alchemy: physmap-flash for all devboards
Replace the devboard NOR MTD mapping driver with physmap-flash support.
Also honor the "swapboot" switch settings wrt. to the layout of the
NOR partitions.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Cc: Linux-MIPS <linux-mips@linux-mips.org> Acked-By: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss [Wed, 28 Oct 2009 20:37:28 +0000 (21:37 +0100)]
SERIAL 8250: Fixes for Alchemy UARTs.
Limit the amount of address space claimed for Alchemy serial ports to
0x1000. On the Au1300, ports are only 0x1000 apart, and the registers
only extend to 0x110 at most on all supported alchemy models.
On the Au1300 the autodetect logic no longer works and this makes it
necessary to specify the port type through platform data. Because of
this the MSR quirk needs to be moved outside the autoconfig() function
which will no longer be called when UPF_FIXED_TYPE is specified.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org>, Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss [Wed, 28 Oct 2009 20:49:46 +0000 (21:49 +0100)]
MIPS: Alchemy: UARTs are of type 16550A
UART autodetection breaks on the Au1300 but the IP blocks are identical,
at least according to the datasheets. Help the 8250 driver by passing
on uart type information via platform data.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss [Thu, 15 Oct 2009 16:49:27 +0000 (18:49 +0200)]
MIPS: Alchemy: prom_putchar is board dependent
This patch replaces the general alchemy prom_putchar() implementation
in favor of board-specific versions: The UART where the output of
prom_putchar is directed to really depends on the board, the current
implementation hardcodes this on a per-SoC basis which is just wrong.
So a generic uart tx function is provided in the alchemy headers,
and the boards can provide their own prom_putchar with custom
destination uart, and all in-kernel alchemy boards support
early printk.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss [Tue, 13 Oct 2009 18:22:35 +0000 (20:22 +0200)]
MIPS: Alchemy: change dbdma to accept physical memory addresses
DMA can only be done from physical addresses; move the "virt_to_phys"
source/destination buffer address translation from the dbdma queueing
functions (since the hardware can only DMA to/from physical addresses)
to their respective users.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss [Tue, 13 Oct 2009 18:22:34 +0000 (20:22 +0200)]
MIPS: Alchemy: remove dbdma compat macros
Remove dbdma compat macros, move remaining users over to default
queueing functions and -flags.
(Queueing function signature has changed in order to give
a build failure instead of silent functional changes due
to the no longer implicitly specified DDMA_FLAGS_IE flag)
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss [Wed, 7 Oct 2009 18:15:15 +0000 (20:15 +0200)]
MIPS: Alchemy: Stop IRQ name sharing
Eliminate the sharing of IRQ names among the differenct Alchemy
variants. IRQ numbers need no longer be hidden behind a
CONFIG_SOC_AU1XXX symbol: step 1 in my quest to make the Alchemy
code less reliant on a hardcoded subtype.
This patch also renames the GPIO irq number constants. It's really
an interrupt line, NOT a GPIO number!
Code which relied on certain irq numbers to have the same name
across all supported cpu subtypes is changed to determine current
cpu subtype at runtime; in some places this isn't possible so
a "compat" symbol is used.
Run-tested on DB1200.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Alchemy hardware provides a method to prioritize interrupts
on a controller by assigning them to a differenct core request line.
Assign usb device request interrupt to IC0 Request 0 (which has
highest priority in the core and the dispatcher) and others to
Request 1. The explicit check for usb device request occurrence
should be obsolete now.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss [Sun, 4 Oct 2009 12:55:28 +0000 (14:55 +0200)]
MIPS: Alchemy: devboards: wire up new PCMCIA driver.
Register the PCMCIA driver on all boards supported by it,
get rid of now-unused pcmcia macros in the board headers
(and subsequently empty pb1100/pb1500 ones).
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss [Sun, 4 Oct 2009 12:55:27 +0000 (14:55 +0200)]
MIPS: PCMCIA: new socket driver for Au1000 demoboards.
New PCMCIA socket driver for all Db/Pb1xxx boards (except Pb1000),
which replaces au1000_db1x00.c and (most of) au1000_pb1x00.c.
Notable improvements:
- supports Db1000, DB/PB1100/1500/1550/1200.
- support for carddetect and statuschange IRQs.
- pcmcia socket mem/io/attr areas and irqs passed through
platform resource information.
- doesn't freeze system during card insertion/ejection like
the one it replaces.
- boardtype is automatically detected using BCSR ID register.
Manuel Lauss [Sun, 4 Oct 2009 12:55:26 +0000 (14:55 +0200)]
MIPS: Alchemy: remove board_init_irq() function.
remove board_init_irq(): On all in-kernel boards it is sufficient to
initialize board interrupts in an arch_initcall by using the default
linux irq functions.
Some small irqmap.c files have been folded into board_setup files.
Run-tested on DB1200; compile-tested on all other affected boards.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss [Sun, 4 Oct 2009 12:55:24 +0000 (14:55 +0200)]
MIPS: Alchemy: devboard register abstraction
All Alchemy development boards have external CPLDs with a few registers
in them. They all share an identical register layout with only a few
minor differences (except the PB1000) in bit functions and base
addresses.
This patch
- adds a primitive facility to initialize and use these external
registers,
- replaces all occurrences of bcsr->xxx accesses with calls to the new
functions (the pb1200 cascade irq handling code is special).
- collects BCSR register information scattered throughout the board
headers in a central place.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Christian Kujau [Fri, 26 Feb 2010 17:25:14 +0000 (17:25 +0000)]
Remove EXPERIMENTAL from NFS_FSCACHE
There's currently an open Ubuntu bug[0], with the intent to compile NFS_FSCACHE
(and possibly AFS_FSCACHE, 9P_FSCACHE) into the standard Ubuntu kernel.
However, since *_FSCACHE still depends on EXPERIMENTAL, this won't happen.
As Arjan van de Ven pointed out[1], the EXPERIMENTAL flag doesn't mean that
much any more, I propose the following patch to fs/nfs/Kconfig. I'd do the
same for fs/9p/Kconfig and fs/afs/Kconfig, but as I did not test 9p or AFS, I
feel it would not be appropriate for me to remove the flag.
Linus Torvalds [Sat, 27 Feb 2010 01:20:18 +0000 (17:20 -0800)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
toshiba_acpi: Add full hotkey support
hp-wmi: Add support for tablet rotation key
dell-laptop: Add another Dell laptop to the DMI whitelist
classmate-laptop: use a single MODULE_DEVICE_TABLE to get correct aliases
dell-laptop: Pay attention to which devices the hardware switch controls
dell-laptop: Use buffer with 32-bit physical address
dell-laptop: Blacklist machines not supporting dell-laptop
dell-laptop: Block software state changes when rfkill hard blocked
dell-laptop: Fix small memory leak
dell-laptop: Fix platform device unregistration
dell-laptop: Update rfkill state on kill switch
compal-laptop: Replace sysfs support with rfkill support
compal-laptop: Add support for known Compal made Dell laptops
MAINTAINERS: update drivers/platform/x86 information
Linus Torvalds [Sat, 27 Feb 2010 01:19:30 +0000 (17:19 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
dlm: use bastmode in debugfs output
dlm: Send lockspace name with uevents
dlm: send reply before bast
dlm: fix ordering of bast and cast
Linus Torvalds [Sat, 27 Feb 2010 01:18:52 +0000 (17:18 -0800)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
* 'for-linus' of git://oss.sgi.com/xfs/xfs: (52 commits)
fs/xfs: Correct NULL test
xfs: optimize log flushing in xfs_fsync
xfs: only clear the suid bit once in xfs_write
xfs: kill xfs_bawrite
xfs: log changed inodes instead of writing them synchronously
xfs: remove invalid barrier optimization from xfs_fsync
xfs: kill the unused XFS_QMOPT_* flush flags V2
xfs: Use delay write promotion for dquot flushing
xfs: Sort delayed write buffers before dispatch
xfs: Don't issue buffer IO direct from AIL push V2
xfs: Use delayed write for inodes rather than async V2
xfs: Make inode reclaim states explicit
xfs: more reserved blocks fixups
xfs: turn off sign warnings
xfs: don't hold onto reserved blocks on remount,ro
xfs: quota limit statvfs available blocks
xfs: replace KM_LARGE with explicit vmalloc use
xfs: cleanup up xfs_log_force calling conventions
xfs: kill XLOG_VEC_SET_TYPE
xfs: remove duplicate buffer flags
...
Linus Torvalds [Sat, 27 Feb 2010 01:16:20 +0000 (17:16 -0800)]
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (362 commits)
V4L-DVB: cx88-dvb: remove extra attribution for core
V4L/DVB: v4l: soc_camera: fix bound checking of mbus_fmt[] index
V4L/DVB: Add support for SMT7020 to cx88
V4L/DVB: radio-si470x: Use UTF-8 encoding on a comment
V4L/DVB: MAINTAINERS: Telegent tlg2300 section fix
V4L/DVB: gspca_stv06xx: Add support for camera button
V4L/DVB: gspca_ov519: add support for the button on ov511 based cams
V4L/DVB: gspca_ov519: Add support for the button on ov518 based cams
V4L/DVB: gspca_ov519: add support for the button on ov519 based cams
V4L/DVB: gspca_main: Fix a compile error when CONFIG_INPUT is not set
V4L/DVB: gspca_main: some input error handling fixes
V4L/DVB: gspca_main: Allow use of input device creation code for non int. inputs
V4L/DVB: gspca_pac7302: much improved exposure control
V4L/DVB: gspca_sonixb: Make sonixb driver handle pas106 and pas202 cameras
V4L/DVB: gspca_sonixb: pas106: fixup bright ctrl and add gain and exposure ctrls
V4L/DVB: Documentation: gspca.txt: update known mr97310a cams
V4L/DVB: gspca_mr97310a: add support for the Sakar 1638x CyberPix
V4L/DVB: gscpa_sonixb: limit ov7630 max framerate at 640x480
V4L/DVB: gspca_sonixb: pas202: fixup brightness ctrl and add gain and exposure ctrls
V4L/DVB: gscpa_sonixb: Differentiate between sensors with a coarse and fine expo ctrl
...
Ang Way Chuang [Thu, 25 Feb 2010 01:45:03 +0000 (09:45 +0800)]
dvb-core: Fix DoS bug in ULE decapsulation code that can be triggered by an invalid Payload Pointer
ULE (Unidirectional Lightweight Encapsulation RFC 4326) decapsulation
has a bug that causes endless loop when Payload Pointer of MPEG2-TS
frame is 182 or 183. Anyone who sends malicious MPEG2-TS frame will
cause the receiver of ULE SNDU to go into endless loop.
This patch was generated and tested against linux-2.6.32.9 and should
apply cleanly to linux-2.6.33 as well because there was only one typo
fix to dvb_net.c since v2.6.32.
This bug was brought to you by modern day Santa Claus who decided to
shower the satellite dish at Keio University with heavy snow causing
huge burst of errors. We, receiver end, received Santa Claus's gift in
the form of kernel bug.
Care has been taken not to introduce more bug by fixing this bug, but
please scrutinize the code for I always produces buggy code.
Signed-off-by: Ang Way Chuang <wcang79@gmail.com> Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 27 Feb 2010 01:11:11 +0000 (17:11 -0800)]
Merge branch 'kmemcheck-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6
* 'kmemcheck-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
kmemcheck: Test the full object in kmemcheck_is_obj_initialized()
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/xfs-vipt:
xfs: fix xfs to work with Virtually Indexed architectures
sh: add mm API for DMA to vmalloc/vmap areas
arm: add mm API for DMA to vmalloc/vmap areas
parisc: add mm API for DMA to vmalloc/vmap areas
mm: add coherence API for DMA to vmalloc/vmap areas
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (187 commits)
sh: remove dead LED code for migo-r and ms7724se
sh: ecovec build fix for CONFIG_I2C=n
sh: ecovec r-standby support
sh: ms7724se r-standby support
sh: SH-Mobile R-standby register save/restore
clocksource: Fix up a registration/IRQ race in the sh drivers.
sh: ms7724: modify scan_timing for KEYSC
sh: ms7724: Add sh_sir support
sh: mach-ecovec24: Add sh_sir support
sh: wire up SET/GET_UNALIGN_CTL.
sh: allow alignment fault mode to be configured at kernel boot.
sh: sh7724: Update FSI/SPU2 clock
sh: always enable sh7724 vpu_clk and set to 166MHz on Ecovec
sh: add sh7724 kick callback to clk_div4_table
sh: introduce struct clk_div4_table
sh: clock-cpg div4 set_rate() shift fix
sh: Turn on speculative return for SH7785 and SH7786
sh: Merge legacy and dynamic PMB modes.
sh: Use uncached I/O helpers in PMB setup.
sh: Provide uncached I/O helpers.
...
Joe Perches [Thu, 14 Jan 2010 16:34:19 +0000 (11:34 -0500)]
drivers/firmware/iscsi_ibft.c: remove NIPQUAD_FMT, use %pI4
Convert netmask to __be32 and format it with %pI4
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Konrad Rzeszutek <ketuzsezr@darnok.org> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Cc: Peter Jones <pjones@redhat.com> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The hibernate memory preallocation code allocates memory to push some
user space data out of physical RAM, so that the hibernation image is
not too large. It allocates more memory than necessary for creating
the image, so it has to release some pages to make room for
allocations made while suspending devices and disabling nonboot CPUs,
or the system will hang due to the lack of free pages to allocate
from. Unfortunately, the function used for freeing these pages,
free_unnecessary_pages(), contains a bug that prevents it from doing
the job on all systems without highmem.
Fix this problem, which is a regression from the 2.6.30 kernel, by
using the right condition for the termination of the loop in
free_unnecessary_pages().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Reported-and-tested-by: Alan Jenkins <sourcejedi.lkml@googlemail.com> Cc: stable@kernel.org
Jiri Slaby [Sun, 21 Feb 2010 21:14:44 +0000 (22:14 +0100)]
PM / Hibernate: Remove swsusp.c finally
Its contents and entry in Makefile were already removed in 8e60c6a1348e17e68ad73589a52a03876e7059be
(Shift remaining code from swsusp.c to hibernate.c)
but somehow it remained in-place (rjw: which most likely was my
mistake).
Signed-off-by: Jiri Slaby <jslaby@suse.cz> Acked-by: Nigel Cunningham <nigel@tuxonice.net> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
PM: Allow SCSI devices to suspend/resume asynchronously
Set power.async_suspend for all SCSI devices, targets and hosts, so
that they can be suspended and resumed in parallel with the main
suspend/resume thread and possibly with other devices they don't
depend on in a known way (i.e. devices which are not their parents or
children).
The power.async_suspend flag is also set for devices that don't have
suspend or resume callbacks, because otherwise they would make the
main suspend/resume thread wait for their "asynchronous" children
(during suspend) or parents (during resume), effectively negating the
possible gains from executing these devices' suspend and resume
callbacks asynchronously.
PM: Allow USB devices to suspend/resume asynchronously
Set power.async_suspend for USB devices, endpoints and interfaces,
allowing them to be suspended and resumed asynchronously during
system sleep transitions.
The power.async_suspend flag is also set for devices that don't have
suspend or resume callbacks, because otherwise they would make the
main suspend/resume thread wait for their "asynchronous" children
(during suspend) or parents (during resume), effectively negating the
possible gains from executing these devices' suspend and resume
callbacks asynchronously.
Alan Stern [Fri, 12 Feb 2010 11:21:11 +0000 (12:21 +0100)]
USB: implement non-tree resume ordering constraints for PCI host controllers
This patch (as1331) adds non-tree ordering constraints needed for
proper resume of PCI USB host controllers from hibernation. The main
issue is that non-high-speed devices must not be resumed before the
high-speed root hub, because it is the ehci_bus_resume() routine which
takes care of handing the device connection over to the companion
controller. If the device resume is attempted before the handover
then the device won't be found and it will be treated as though it had
disconnected.
The patch adds a new field to the usb_bus structure; for each
full/low-speed bus this field will contain a pointer to the companion
high-speed bus (if one exists). It is used during normal device
resume; if the hs_companion pointer isn't NULL then we wait for the
root-hub device on the hs_companion bus.
A secondary issue is that an EHCI controlller shouldn't be resumed
before any of its companions. On some machines I have observed
handovers failing if the companion controller is reinitialized after
the handover. Thus, the EHCI resume routine must wait for the
companion controllers to be resumed.
The patch also fixes a small bug in usb_hcd_pci_probe(); an error path
jumps to the wrong label, causing a memory leak.
[rjw: Fixed compilation for CONFIG_PM_SLEEP unset.]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
PM: Allow PCI devices to suspend/resume asynchronously
Set power.async_suspend for all PCI devices and PCIe port services,
so that they can be suspended and resumed in parallel with other
devices they don't depend on in a known way (i.e. devices which are
not their parents or children).
This only affects the "regular" suspend and resume stages, which
means in particular that the restoration of the PCI devices' standard
configuration registers during resume will still be carried out
synchronously (at the "early" resume stage).
Jiri Slaby [Wed, 27 Jan 2010 22:47:56 +0000 (23:47 +0100)]
PM / Hibernate: Swap, remove useless check from swsusp_read()
It will never reach here if the sws_resume_bdev is erratic.
swsusp_read() is called only from software_resume(), but after
swsusp_check() which would catch the error state.
Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
There are some dependencies between devices (in particular, between
EHCI USB controllers and their OHCI/UHCI siblings) which are not
reflected by the structure of the device tree. With synchronous
suspend and resume these dependencies are taken into accout
automatically, because the devices in question are always registered
in the right order, but to meet these constraints with asynchronous
suspend and resume the drivers of these devices will need to use
dpm_wait() in their suspend/resume routines, so introduce a helper
function allowing them to do that.
It has been shown by testing that total device resume time can be
reduced significantly (by as much as 50% or more) if the async
threads executing some devices' resume routines are all started
before the main resume thread starts to handle the "synchronous"
devices.
This is a consequence of the fact that the slowest devices tend to be
located at the end of dpm_list, so their resume routines are started
very late. Consequently, they have to wait for all the preceding
"synchronous" devices before their resume routines can be started
by the main resume thread, even if they are "asynchronous". By
starting their async threads upfront we effectively move those
devices towards the beginning of dpm_list, without breaking their
ordering with respect to their parents and children. As a result,
their resume routines are started much earlier and we are able to
save much more device resume time this way.
PM: Add facility for advanced testing of async suspend/resume
Add configuration switch CONFIG_PM_ADVANCED_DEBUG for compiling in
extra PM debugging/testing code allowing one to access some
PM-related attributes of devices from the user space via sysfs.
If CONFIG_PM_ADVANCED_DEBUG is set, add sysfs attribute power/async
for every device allowing the user space to access the device's
power.async_suspend flag and modify it, if desired.
Theoretically, the total time of system sleep transitions (suspend
to RAM, hibernation) can be reduced by running suspend and resume
callbacks of device drivers in parallel with each other. However,
there are dependencies between devices such that we're not allowed
to suspend the parent of a device before suspending the device
itself. Analogously, we're not allowed to resume a device before
resuming its parent.
The most straightforward way to take these dependencies into accout
is to start the async threads used for suspending and resuming
devices at the core level, so that async_schedule() is called for
each suspend and resume callback supposed to be executed
asynchronously.
For this purpose, introduce a new device flag, power.async_suspend,
used to mark the devices whose suspend and resume callbacks are to be
executed asynchronously (ie. in parallel with the main suspend/resume
thread and possibly in parallel with each other) and helper function
device_enable_async_suspend() allowing one to set power.async_suspend
for given device (power.async_suspend is unset by default for all
devices). For each device with the power.async_suspend flag set the
PM core will use async_schedule() to execute its suspend and resume
callbacks.
The async threads started for different devices as a result of
calling async_schedule() are synchronized with each other and with
the main suspend/resume thread with the help of completions, in the
following way:
(1) There is a completion, power.completion, for each device object.
(2) Each device's completion is reset before calling async_schedule()
for the device or, in the case of devices with the
power.async_suspend flags unset, before executing the device's
suspend and resume callbacks.
(3) During suspend, right before running the bus type, device type
and device class suspend callbacks for the device, the PM core
waits for the completions of all the device's children to be
completed.
(4) During resume, right before running the bus type, device type and
device class resume callbacks for the device, the PM core waits
for the completion of the device's parent to be completed.
(5) The PM core completes power.completion for each device right
after the bus type, device type and device class suspend (or
resume) callbacks executed for the device have returned.
Add new device sysfs attribute, power/control, allowing the user
space to block the run-time power management of the devices. If this
attribute is set to "on", the driver of the device won't be able to power
manage it at run time (without breaking the rules) and the device will
always be in the full power state (except when the entire system goes
into a sleep state).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Alan Stern <stern@rowland.harvard.edu>
V4L-DVB: cx88-dvb: remove extra attribution for core
This is not needed, since the function already do it. Also, it causes
a warning at the compilation, since a new var is declared in the middle
of the code.
Linus Torvalds [Fri, 26 Feb 2010 18:35:27 +0000 (10:35 -0800)]
Merge branch 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (48 commits)
x86/PCI: Prevent mmconfig memory corruption
ACPI: Use GPE reference counting to support shared GPEs
x86/PCI: use host bridge _CRS info by default on 2008 and newer machines
PCI: augment bus resource table with a list
PCI: add pci_bus_for_each_resource(), remove direct bus->resource[] refs
PCI: read bridge windows before filling in subtractive decode resources
PCI: split up pci_read_bridge_bases()
PCIe PME: use pci_pcie_cap()
PCI PM: Run-time callbacks for PCI bus type
PCIe PME: use pci_is_pcie()
PCI / ACPI / PM: Platform support for PCI PME wake-up
ACPI / ACPICA: Multiple system notify handlers per device
ACPI / PM: Add more run-time wake-up fields
ACPI: Use GPE reference counting to support shared GPEs
PCI PM: Make it possible to force using INTx for PCIe PME signaling
PCI PM: PCIe PME root port service driver
PCI PM: Add function for checking PME status of devices
PCI: mark is_pcie obsolete
PCI: set PCI_PREF_RANGE_TYPE_64 in pci_bridge_check_ranges
PCI: pciehp: second try to get big range for pcie devices
...
David Teigland [Thu, 25 Feb 2010 18:20:57 +0000 (12:20 -0600)]
dlm: use bastmode in debugfs output
The bast mode that appears in the debugfs output should be
useful on both master and process nodes. lkb_highbast is
currently printed, and is only useful on the master node.
lkb_bastmode is only useful on the process node. This
patch sets lkb_bastmode on the master node as well, and
uses that value in the debugfs print.
Signed-off-by: David Teigland <teigland@redhat.com>
Hans de Goede [Fri, 19 Feb 2010 07:41:40 +0000 (04:41 -0300)]
V4L/DVB: gspca_main: some input error handling fixes
2 small changes to input device error handling:
1) Make it fatal when we fail to create an input device (it is either this
or add checks for gspca_dev->input_dev being NULL in a lot of places)
2) Since we allow gspca_input_create_urb() to fail everywhere we call it,
and thus never check its return value, make it void.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
projects / mirror_ubuntu-eoan-kernel.git / log