Commit e49ce14150c6 ("modpost: use linker section to generate table.")
was not so cool as we had expected first; it ended up with ugly section
hacks when commit dd2a3acaecd7 ("mod/file2alias: make modpost compile
on darwin again") came in.
Given a certain degree of unknowledge about the link stage of host
programs, I really want to see simple, stupid table lookup so that
this works in the same way regardless of the underlying executable
format.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Mathieu Malaterre <malat@debian.org>
[nc: Omit rpmsg, sdw, tbsvc, and typec as they do not exist here] Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If the host controller supports auto-commands then enable the auto-command
error interrupt and handle it. In the case of auto-CMD23, the error is
treated the same as manual CMD23 error. In the case of auto-CMD12,
commands-during-transfer are not permitted, so the error handling is
treated the same as a data error.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The SDHCI_ACMD12_ERR register is used for auto-CMD23 and auto-CMD12
errors, as is the SDHCI_INT_ACMD12ERR interrupt bit. Rename them to
SDHCI_AUTO_CMD_STATUS and SDHCI_INT_AUTO_CMD_ERR respectively.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Existing data command CRC error handling is non-standard and does not work
with some Intel host controllers. Specifically, the assumption that the host
controller will continue operating normally after the error interrupt,
is not valid. Change the driver to handle the error in the same manner
as a data CRC error, taking care to ensure that the data line reset is
done for single or multi-block transfers, and it is done before
unmapping DMA.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This patch fixes cts(cbc(aes)) test when cbc-aes-ppc4xx is used.
alg: skcipher: Test 1 failed (invalid result) on encryption for cts(cbc-aes-ppc4xx) 00000000: 4b 10 75 fc 2f 14 1b 6a 27 35 37 33 d1 b7 70 05 00000010: 97
alg: skcipher: Failed to load transform for cts(cbc(aes)): -2
The CTS cipher mode expect the IV (req->iv) of skcipher_request
to contain the last ciphertext block after the {en,de}crypt
operation is complete.
Fix this issue for the AMCC Crypto4xx hardware engine.
The tcrypt test case for cts(cbc(aes)) is now correctly passed.
name : cts(cbc(aes))
driver : cts(cbc-aes-ppc4xx)
module : cts
priority : 300
refcnt : 1
selftest : passed
internal : no
type : skcipher
async : yes
blocksize : 16
min keysize : 16
max keysize : 32
ivsize : 16
chunksize : 16
walksize : 16
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The connection between sighand->siglock and st->lock comes through seccomp,
which takes st->lock while holding sighand->siglock.
Make sure interrupts are disabled when __speculation_ctrl_update() is
invoked via prctl() -> speculation_ctrl_update(). Add a lockdep assert to
catch future offenders.
Fixes: 1f50ddb4f418 ("x86/speculation: Handle HT correctly on AMD") Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com> Cc: Thomas Lendacky <thomas.lendacky@amd.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1904141948200.4917@nanos.tec.linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
- Does not support an L2 cache miss event
- It has re-enumerated PMC counters for:
- L2 cache references
- front & back end stalled cycles
So we add a new amd_f17h_perfmon_event_map[] so that the generic
perf event names will resolve to the correct h/w events on
family 17h and above processors.
Reference sections 2.1.13.3.3 (stalls) and 2.1.13.3.6 (L2):
There are several scenarios in which mac80211 can call drv_wake_tx_queue
after ieee80211_restart_hw has been called and has not yet completed.
Driver private structs are considered uninitialized until mac80211 has
uploaded the vifs, stations and keys again, so using private tx queue
data during that time is not safe.
The driver can also not rely on drv_reconfig_complete to figure out when
it is safe to accept drv_wake_tx_queue calls again, because it is only
called after all tx queues are woken again.
To fix this, bail out early in drv_wake_tx_queue if local->in_reconfig
is set.
Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The following commit introduced a bug in one of our error paths:
819319fc9346 ("kprobes: Return error if we fail to reuse kprobe instead of BUG_ON()")
it missed to handle the return value of kprobe_optready() as
error-value. In reality, the kprobe_optready() returns a bool
result, so "true" case must be passed instead of 0.
This causes some errors on kprobe boot-time selftests on ARM:
[ ] Beginning kprobe tests...
[ ] Probe ARM code
[ ] kprobe
[ ] kretprobe
[ ] ARM instruction simulation
[ ] Check decoding tables
[ ] Run test cases
[ ] FAIL: test_case_handler not run
[ ] FAIL: Test andge r10, r11, r14, asr r7
[ ] FAIL: Scenario 11
...
[ ] FAIL: Scenario 7
[ ] Total instruction simulation tests=1631, pass=1433 fail=198
[ ] kprobe tests failed
This can happen if an optimized probe is unregistered and next
kprobe is registered on same address until the previous probe
is not reclaimed.
If this happens, a hidden aggregated probe may be kept in memory,
and no new kprobe can probe same address. Also, in that case
register_kprobe() will return "1" instead of minus error value,
which can mislead caller logic.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com> Cc: David S . Miller <davem@davemloft.net> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Naveen N . Rao <naveen.n.rao@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org # v5.0+ Fixes: 819319fc9346 ("kprobes: Return error if we fail to reuse kprobe instead of BUG_ON()") Link: http://lkml.kernel.org/r/155530808559.32517.539898325433642204.stgit@devnote2 Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Mark ftrace mcount handler functions nokprobe since
probing on these functions with kretprobe pushes
return address incorrectly on kretprobe shadow stack.
Reported-by: Francis Deslauriers <francis.deslauriers@efficios.com> Tested-by: Andrea Righi <righi.andrea@gmail.com> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Acked-by: Steven Rostedt <rostedt@goodmis.org> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/155094062044.6137.6419622920568680640.stgit@devbox Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Verify the stack frame pointer on kretprobe trampoline handler,
If the stack frame pointer does not match, it skips the wrong
entry and tries to find correct one.
This can happen if user puts the kretprobe on the function
which can be used in the path of ftrace user-function call.
Such functions should not be probed, so this adds a warning
message that reports which function should be blacklisted.
Tested-by: Andrea Righi <righi.andrea@gmail.com> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Acked-by: Steven Rostedt <rostedt@goodmis.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/155094059185.6137.15527904013362842072.stgit@devbox Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 045afc24124d ("arm64: futex: Fix FUTEX_WAKE_OP atomic ops with
non-zero result value") removed oldval's zero initialization in
arch_futex_atomic_op_inuser because it is not necessary. Unfortunately,
Android's arm64 GCC 4.9.4 [1] does not agree:
../kernel/futex.c: In function 'do_futex':
../kernel/futex.c:1658:17: warning: 'oldval' may be used uninitialized
in this function [-Wmaybe-uninitialized]
return oldval == cmparg;
^
In file included from ../kernel/futex.c:73:0:
../arch/arm64/include/asm/futex.h:53:6: note: 'oldval' was declared here
int oldval, ret, tmp;
^
GCC fails to follow that when ret is non-zero, futex_atomic_op_inuser
returns right away, avoiding the uninitialized use that it claims.
Restoring the zero initialization works around this issue.
The x86_64 implementation of Poly1305 produces the wrong result on some
inputs because poly1305_4block_avx2() incorrectly assumes that when
partially reducing the accumulator, the bits carried from limb 'd4' to
limb 'h0' fit in a 32-bit integer. This is true for poly1305-generic
which processes only one block at a time. However, it's not true for
the AVX2 implementation, which processes 4 blocks at a time and
therefore can produce intermediate limbs about 4x larger.
Fix it by making the relevant calculations use 64-bit arithmetic rather
than 32-bit. Note that most of the carries already used 64-bit
arithmetic, but the d4 -> h0 carry was different for some reason.
To be safe I also made the same change to the corresponding SSE2 code,
though that only operates on 1 or 2 blocks at a time. I don't think
it's really needed for poly1305_block_sse2(), but it doesn't hurt
because it's already x86_64 code. It *might* be needed for
poly1305_2block_sse2(), but overflows aren't easy to reproduce there.
This bug was originally detected by my patches that improve testmgr to
fuzz algorithms against their generic implementation. But also add a
test vector which reproduces it directly (in the AVX2 case).
Fixes: b1ccc8f4b631 ("crypto: poly1305 - Add a four block AVX2 variant for x86_64") Fixes: c70f4abef07a ("crypto: poly1305 - Add a SSE2 SIMD variant for x86_64") Cc: <stable@vger.kernel.org> # v4.3+ Cc: Martin Willi <martin@strongswan.org> Cc: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Martin Willi <martin@strongswan.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The core dumping code has always run without holding the mmap_sem for
writing, despite that is the only way to ensure that the entire vma
layout will not change from under it. Only using some signal
serialization on the processes belonging to the mm is not nearly enough.
This was pointed out earlier. For example in Hugh's post from Jul 2017:
"Not strictly relevant here, but a related note: I was very surprised
to discover, only quite recently, how handle_mm_fault() may be called
without down_read(mmap_sem) - when core dumping. That seems a
misguided optimization to me, which would also be nice to correct"
In particular because the growsdown and growsup can move the
vm_start/vm_end the various loops the core dump does around the vma will
not be consistent if page faults can happen concurrently.
Pretty much all users calling mmget_not_zero()/get_task_mm() and then
taking the mmap_sem had the potential to introduce unexpected side
effects in the core dumping code.
Adding mmap_sem for writing around the ->core_dump invocation is a
viable long term fix, but it requires removing all copy user and page
faults and to replace them with get_dump_page() for all binary formats
which is not suitable as a short term fix.
For the time being this solution manually covers the places that can
confuse the core dump either by altering the vma layout or the vma flags
while it runs. Once ->core_dump runs under mmap_sem for writing the
function mmget_still_valid() can be dropped.
Allowing mmap_sem protected sections to run in parallel with the
coredump provides some minor parallelism advantage to the swapoff code
(which seems to be safe enough by never mangling any vma field and can
keep doing swapins in parallel to the core dumping) and to some other
corner case.
In order to facilitate the backporting I added "Fixes: 86039bd3b4e6"
however the side effect of this same race condition in /proc/pid/mem
should be reproducible since before 2.6.12-rc2 so I couldn't add any
other "Fixes:" because there's no hash beyond the git genesis commit.
Because find_extend_vma() is the only location outside of the process
context that could modify the "mm" structures under mmap_sem for
reading, by adding the mmget_still_valid() check to it, all other cases
that take the mmap_sem for reading don't need the new check after
mmget_not_zero()/get_task_mm(). The expand_stack() in page fault
context also doesn't need the new check, because all tasks under core
dumping are frozen.
Link: http://lkml.kernel.org/r/20190325224949.11068-1-aarcange@redhat.com Fixes: 86039bd3b4e6 ("userfaultfd: add new syscall to provide memory externalization") Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Reported-by: Jann Horn <jannh@google.com> Suggested-by: Oleg Nesterov <oleg@redhat.com> Acked-by: Peter Xu <peterx@redhat.com> Reviewed-by: Mike Rapoport <rppt@linux.ibm.com> Reviewed-by: Oleg Nesterov <oleg@redhat.com> Reviewed-by: Jann Horn <jannh@google.com> Acked-by: Jason Gunthorpe <jgg@mellanox.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When SCSI blk-mq is enabled, there is a bug in handling errors in
scsi_queue_rq. Specifically, the bug is not setting result field of
scsi_request correctly when the dispatch of the command has been
failed. Since the upper layer code including the sg_io ioctl expects to
receive any error status from result field of scsi_request, the error is
silently ignored and this could cause data corruptions for some
applications.
Fixes: d285203cf647 ("scsi: add support for a blk-mq based I/O path.") Cc: <stable@vger.kernel.org> Signed-off-by: Jaesoo Lee <jalee@purestorage.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There is a small race window in the card disconnection code that
allows the registration of another card with the very same card id.
This leads to a warning in procfs creation as caught by syzkaller.
The problem is that we delete snd_cards and snd_cards_lock entries at
the very beginning of the disconnection procedure. This makes the
slot available to be assigned for another card object while the
disconnection procedure is being processed. Then it becomes possible
to issue a procfs registration with the existing file name although we
check the conflict beforehand.
The fix is simply to move the snd_cards and snd_cards_lock clearances
at the end of the disconnection procedure. The references to these
entries are merely either from the global proc files like
/proc/asound/cards or from the card registration / disconnection, so
it should be fine to shift at the very end.
`ni6501_alloc_usb_buffers()` is called from `ni6501_auto_attach()` to
allocate RX and TX buffers for USB transfers. It allocates
`devpriv->usb_rx_buf` followed by `devpriv->usb_tx_buf`. If the
allocation of `devpriv->usb_tx_buf` fails, it frees
`devpriv->usb_rx_buf`, leaving the pointer set dangling, and returns an
error. Later, `ni6501_detach()` will be called from the core comedi
module code to clean up. `ni6501_detach()` also frees both
`devpriv->usb_rx_buf` and `devpriv->usb_tx_buf`, but
`devpriv->usb_rx_buf` may have already beed freed, leading to a
double-free error. Fix it bu removing the call to
`kfree(devpriv->usb_rx_buf)` from `ni6501_alloc_usb_buffers()`, relying
on `ni6501_detach()` to free the memory.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If `ni6501_auto_attach()` returns an error, the core comedi module code
will call `ni6501_detach()` to clean up. If `ni6501_auto_attach()`
successfully allocated the comedi device private data, `ni6501_detach()`
assumes that a `struct mutex mut` contained in the private data has been
initialized and uses it. Unfortunately, there are a couple of places
where `ni6501_auto_attach()` can return an error after allocating the
device private data but before initializing the mutex, so this
assumption is invalid. Fix it by initializing the mutex just after
allocating the private data in `ni6501_auto_attach()` before any other
errors can be retturned. Also move the call to `usb_set_intfdata()`
just to keep the code a bit neater (either position for the call is
fine).
I believe this was the cause of the following syzbot crash report
<https://syzkaller.appspot.com/bug?extid=cf4f2b6c24aff0a3edf6>:
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 1-1: config 0 descriptor??
usb 1-1: string descriptor 0 read error: -71
comedi comedi0: Wrong number of endpoints
ni6501 1-1:0.233: driver 'ni6501' failed to auto-configure device.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 585 Comm: kworker/0:3 Not tainted 5.1.0-rc4-319354-g9a33b36 #3
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xe8/0x16e lib/dump_stack.c:113
assign_lock_key kernel/locking/lockdep.c:786 [inline]
register_lock_class+0x11b8/0x1250 kernel/locking/lockdep.c:1095
__lock_acquire+0xfb/0x37c0 kernel/locking/lockdep.c:3582
lock_acquire+0x10d/0x2f0 kernel/locking/lockdep.c:4211
__mutex_lock_common kernel/locking/mutex.c:925 [inline]
__mutex_lock+0xfe/0x12b0 kernel/locking/mutex.c:1072
ni6501_detach+0x5b/0x110 drivers/staging/comedi/drivers/ni_usb6501.c:567
comedi_device_detach+0xed/0x800 drivers/staging/comedi/drivers.c:204
comedi_device_cleanup.part.0+0x68/0x140 drivers/staging/comedi/comedi_fops.c:156
comedi_device_cleanup drivers/staging/comedi/comedi_fops.c:187 [inline]
comedi_free_board_dev.part.0+0x16/0x90 drivers/staging/comedi/comedi_fops.c:190
comedi_free_board_dev drivers/staging/comedi/comedi_fops.c:189 [inline]
comedi_release_hardware_device+0x111/0x140 drivers/staging/comedi/comedi_fops.c:2880
comedi_auto_config.cold+0x124/0x1b0 drivers/staging/comedi/drivers.c:1068
usb_probe_interface+0x31d/0x820 drivers/usb/core/driver.c:361
really_probe+0x2da/0xb10 drivers/base/dd.c:509
driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
__device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
__device_attach+0x223/0x3a0 drivers/base/dd.c:844
bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
device_add+0xad2/0x16e0 drivers/base/core.c:2106
usb_set_configuration+0xdf7/0x1740 drivers/usb/core/message.c:2021
generic_probe+0xa2/0xda drivers/usb/core/generic.c:210
usb_probe_device+0xc0/0x150 drivers/usb/core/driver.c:266
really_probe+0x2da/0xb10 drivers/base/dd.c:509
driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
__device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
__device_attach+0x223/0x3a0 drivers/base/dd.c:844
bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
device_add+0xad2/0x16e0 drivers/base/core.c:2106
usb_new_device.cold+0x537/0xccf drivers/usb/core/hub.c:2534
hub_port_connect drivers/usb/core/hub.c:5089 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5204 [inline]
port_event drivers/usb/core/hub.c:5350 [inline]
hub_event+0x138e/0x3b00 drivers/usb/core/hub.c:5432
process_one_work+0x90f/0x1580 kernel/workqueue.c:2269
worker_thread+0x9b/0xe20 kernel/workqueue.c:2415
kthread+0x313/0x420 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
`vmk80xx_alloc_usb_buffers()` is called from `vmk80xx_auto_attach()` to
allocate RX and TX buffers for USB transfers. It allocates
`devpriv->usb_rx_buf` followed by `devpriv->usb_tx_buf`. If the
allocation of `devpriv->usb_tx_buf` fails, it frees
`devpriv->usb_rx_buf`, leaving the pointer set dangling, and returns an
error. Later, `vmk80xx_detach()` will be called from the core comedi
module code to clean up. `vmk80xx_detach()` also frees both
`devpriv->usb_rx_buf` and `devpriv->usb_tx_buf`, but
`devpriv->usb_rx_buf` may have already been freed, leading to a
double-free error. Fix it by removing the call to
`kfree(devpriv->usb_rx_buf)` from `vmk80xx_alloc_usb_buffers()`, relying
on `vmk80xx_detach()` to free the memory.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If `vmk80xx_auto_attach()` returns an error, the core comedi module code
will call `vmk80xx_detach()` to clean up. If `vmk80xx_auto_attach()`
successfully allocated the comedi device private data,
`vmk80xx_detach()` assumes that a `struct semaphore limit_sem` contained
in the private data has been initialized and uses it. Unfortunately,
there are a couple of places where `vmk80xx_auto_attach()` can return an
error after allocating the device private data but before initializing
the semaphore, so this assumption is invalid. Fix it by initializing
the semaphore just after allocating the private data in
`vmk80xx_auto_attach()` before any other errors can be returned.
I believe this was the cause of the following syzbot crash report
<https://syzkaller.appspot.com/bug?extid=54c2f58f15fe6876b6ad>:
usb 1-1: config 0 has no interface number 0
usb 1-1: New USB device found, idVendor=10cf, idProduct=8068, bcdDevice=e6.8d
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 1-1: config 0 descriptor??
vmk80xx 1-1:0.117: driver 'vmk80xx' failed to auto-configure device.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.1.0-rc4-319354-g9a33b36 #3
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xe8/0x16e lib/dump_stack.c:113
assign_lock_key kernel/locking/lockdep.c:786 [inline]
register_lock_class+0x11b8/0x1250 kernel/locking/lockdep.c:1095
__lock_acquire+0xfb/0x37c0 kernel/locking/lockdep.c:3582
lock_acquire+0x10d/0x2f0 kernel/locking/lockdep.c:4211
__raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline]
_raw_spin_lock_irqsave+0x44/0x60 kernel/locking/spinlock.c:152
down+0x12/0x80 kernel/locking/semaphore.c:58
vmk80xx_detach+0x59/0x100 drivers/staging/comedi/drivers/vmk80xx.c:829
comedi_device_detach+0xed/0x800 drivers/staging/comedi/drivers.c:204
comedi_device_cleanup.part.0+0x68/0x140 drivers/staging/comedi/comedi_fops.c:156
comedi_device_cleanup drivers/staging/comedi/comedi_fops.c:187 [inline]
comedi_free_board_dev.part.0+0x16/0x90 drivers/staging/comedi/comedi_fops.c:190
comedi_free_board_dev drivers/staging/comedi/comedi_fops.c:189 [inline]
comedi_release_hardware_device+0x111/0x140 drivers/staging/comedi/comedi_fops.c:2880
comedi_auto_config.cold+0x124/0x1b0 drivers/staging/comedi/drivers.c:1068
usb_probe_interface+0x31d/0x820 drivers/usb/core/driver.c:361
really_probe+0x2da/0xb10 drivers/base/dd.c:509
driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
__device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
__device_attach+0x223/0x3a0 drivers/base/dd.c:844
bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
device_add+0xad2/0x16e0 drivers/base/core.c:2106
usb_set_configuration+0xdf7/0x1740 drivers/usb/core/message.c:2021
generic_probe+0xa2/0xda drivers/usb/core/generic.c:210
usb_probe_device+0xc0/0x150 drivers/usb/core/driver.c:266
really_probe+0x2da/0xb10 drivers/base/dd.c:509
driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
__device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
__device_attach+0x223/0x3a0 drivers/base/dd.c:844
bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
device_add+0xad2/0x16e0 drivers/base/core.c:2106
usb_new_device.cold+0x537/0xccf drivers/usb/core/hub.c:2534
hub_port_connect drivers/usb/core/hub.c:5089 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5204 [inline]
port_event drivers/usb/core/hub.c:5350 [inline]
hub_event+0x138e/0x3b00 drivers/usb/core/hub.c:5432
process_one_work+0x90f/0x1580 kernel/workqueue.c:2269
worker_thread+0x9b/0xe20 kernel/workqueue.c:2415
kthread+0x313/0x420 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
On some laptops, kxcjk1013 is powered off when system enters S3. We need
restore the range regiter during resume. Otherwise, the sensor doesn't
work properly after S3.
Signed-off-by: he, bo <bo.he@intel.com> Signed-off-by: Chen, Hu <hu1.chen@intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This fixes a possible circular locking dependency detected warning seen
with:
- CONFIG_PROVE_LOCKING=y
- consumer/provider IIO devices (ex: "voltage-divider" consumer of "adc")
When using the IIO consumer interface, e.g. iio_channel_get(), the consumer
device will likely call iio_read_channel_raw() or similar that rely on
'info_exist_lock' mutex.
typically:
...
mutex_lock(&chan->indio_dev->info_exist_lock);
if (chan->indio_dev->info == NULL) {
ret = -ENODEV;
goto err_unlock;
}
ret = do_some_ops()
err_unlock:
mutex_unlock(&chan->indio_dev->info_exist_lock);
return ret;
...
Same mutex is also hold in iio_device_unregister().
The following deadlock warning happens when:
- the consumer device has called an API like iio_read_channel_raw()
at least once.
- the consumer driver is unregistered, removed (unbind from sysfs)
======================================================
WARNING: possible circular locking dependency detected
4.19.24 #577 Not tainted
------------------------------------------------------
sh/372 is trying to acquire lock:
(kn->count#30){++++}, at: kernfs_remove_by_name_ns+0x3c/0x84
but task is already holding lock:
(&dev->info_exist_lock){+.+.}, at: iio_device_unregister+0x18/0x60
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
cdev_device_del() can be called without holding the lock. It should be safe
as info_exist_lock prevents kernelspace consumers to use the exported
routines during/after provider removal. cdev_device_del() is for userspace.
Help to reproduce:
See example: Documentation/devicetree/bindings/iio/afe/voltage-divider.txt
sysv {
compatible = "voltage-divider";
io-channels = <&adc 0>;
output-ohms = <22>;
full-ohms = <222>;
};
First, go to iio:deviceX for the "voltage-divider", do one read:
$ cd /sys/bus/iio/devices/iio:deviceX
$ cat in_voltage0_raw
Then, unbind the consumer driver. It triggers above deadlock warning.
$ cd /sys/bus/platform/drivers/iio-rescale/
$ echo sysv > unbind
Note I don't actually expect stable will pick this up all the
way back into IIO being in staging, but if's probably valid that
far back.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Fixes: ac917a81117c ("staging:iio:core set the iio_dev.info pointer to null on unregister") Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Having a brief look at at91_adc_read_raw() it is obvious that in the case
of a timeout the setting of AT91_ADC_CHDR and AT91_ADC_IDR registers is
omitted. If 2 different channels are queried we can end up with a
situation where two interrupts are enabled, but only one interrupt is
cleared in the interrupt handler. Resulting in a interrupt loop and a
system hang.
Signed-off-by: Georg Ottinger <g.ottinger@abatec.at> Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The trialmask is expected to have all bits set to 0 after allocation.
Currently kmalloc_array() is used which does not zero the memory and so
random bits are set. This results in random channels being enabled when
they shouldn't. Replace kmalloc_array() with kcalloc() which has the same
interface but zeros the memory.
Note the fix is actually required earlier than the below fixes tag, but
will require a manual backport due to move from kmalloc to kmalloc_array.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Fixes commit 057ac1acdfc4 ("iio: Use kmalloc_array() in iio_scan_mask_set()"). Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When issuing the write DAC register and write eeprom command, the two
powerdown bits (PD0 and PD1) are assumed by the chip to be present in
the bytes sent. Leaving them at 0 implies "powerdown disabled" which is
a different state that the current one. By adding the current state of
the powerdown in the i2c write, the chip will correctly power-on exactly
like as it is at the moment of store_eeprom call.
This is documented in MCP4725's datasheet, FIGURE 6-2: "Write Commands
for DAC Input Register and EEPROM" and MCP4726's datasheet, FIGURE 6-3:
"Write All Memory Command".
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com> Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The desired channel has to be selected in order to correctly fill the
buffer with the corresponding data.
The `ad_sd_write_reg()` already does this, but for the
`ad_sd_read_reg_raw()` this was omitted.
Fixes: af3008485ea03 ("iio:adc: Add common code for ADI Sigma Delta devices") Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Calculation did not use IIO_DEGREE_TO_RAD and implemented a variant to
avoid precision loss as we aim a nano value. The offset added to avoid
rounding error, though, doesn't give us a close result to the expected
value. E.g.
I noticed that apic test from kvm-unit-tests always hangs on my EPYC 7401P,
the hanging test nmi-after-sti is trying to deliver 30000 NMIs and tracing
shows that we're sometimes able to deliver a few but never all.
When we're trying to inject an NMI we may fail to do so immediately for
various reasons, however, we still need to inject it so enable_nmi_window()
arms nmi_singlestep mode. #DB occurs as expected, but we're not checking
for pending NMIs before entering the guest and unless there's a different
event to process, the NMI will never get delivered.
Make KVM_REQ_EVENT request on the vCPU from db_interception() to make sure
pending NMIs are checked and possibly injected.
Neither AMD nor Intel CPUs have an EFER field in the legacy SMRAM save
state area, i.e. don't save/restore EFER across SMM transitions. KVM
somewhat models this, e.g. doesn't clear EFER on entry to SMM if the
guest doesn't support long mode. But during RSM, KVM unconditionally
clears EFER so that it can get back to pure 32-bit mode in order to
start loading CRs with their actual non-SMM values.
Clear EFER only when it will be written when loading the non-SMM state
so as to preserve bits that can theoretically be set on 32-bit vCPUs,
e.g. KVM always emulates EFER_SCE.
And because CR4.PAE is cleared only to play nice with EFER, wrap that
code in the long mode check as well. Note, this may result in a
compiler warning about cr4 being consumed uninitialized. Re-read CR4
even though it's technically unnecessary, as doing so allows for more
readable code and RSM emulation is not a performance critical path.
Fixes: 660a5d517aaab ("KVM: x86: save/load state on SMM switch") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The thunderx driver splits frames bigger than 1530 bytes to multiple
pages, making impossible to run an eBPF program on it.
This leads to a maximum MTU of 1508 if QinQ is in use.
The thunderx driver forbids to load an eBPF program if the MTU is higher
than 1500 bytes. Raise the limit to 1508 so it is possible to use L2
protocols which need some more headroom.
Fixes: 05c773f52b96e ("net: thunderx: Add basic XDP support") Signed-off-by: Matteo Croce <mcroce@redhat.com> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Fixes: ed0de45a1008 ("ipv4: recompile ip options in ipv4_link_failure") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: Stephen Suryaputra <ssuryaextr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Recompile IP options since IPCB may not be valid anymore when
ipv4_link_failure is called from arp_error_report.
Refer to the commit 3da1ed7ac398 ("net: avoid use IPCB in cipso_v4_error")
and the commit before that (9ef6b42ad6fd) for a similar issue.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We used to accept zero size iova range which will lead a infinite loop
in translate_desc(). Fixing this by failing the request in this case.
Reported-by: syzbot+d21e6e297322a900c128@syzkaller.appspotmail.com Fixes: 6b1e6cc7 ("vhost: new device IOTLB API") Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
After adding a team interface to bridge, the team interface will enter
promisc mode. Then if we add a new slave to team0, the slave will keep
promisc off. Fix it by setting slave to promisc on if team master is
already in promisc mode, also do the same for allmulti.
v2: add promisc and allmulti checking when delete ports
Fixes: 3d249d4ca7d0 ("net: introduce ethernet teaming device") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For some reason, tcp_grow_window() correctly tests if enough room
is present before attempting to increase tp->rcv_ssthresh,
but does not prevent it to grow past tcp_space()
This is causing hard to debug issues, like failing
the (__tcp_select_window(sk) >= tp->rcv_wnd) test
in __tcp_ack_snd_check(), causing ACK delays and possibly
slow flows.
Depending on tcp_rmem[2], MTU, skb->len/skb->truesize ratio,
we can see the problem happening on "netperf -t TCP_RR -- -r 2000,2000"
after about 60 round trips, when the active side no longer sends
immediate acks.
This bug predates git history.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Wei Wang <weiwan@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
gue tunnels run iptunnel_pull_offloads on received skbs. This can
determine a possible use-after-free accessing guehdr pointer since
the packet will be 'uncloned' running pskb_expand_head if it is a
cloned gso skb (e.g if the packet has been sent though a veth device)
Fixes: a09a4c8dd1ec ("tunnels: Remove encapsulation offloads on decap") Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
br_multicast_start_querier() walks over the port list but it can be
called from a timer with only multicast_lock held which doesn't protect
the port list, so use RCU to walk over it.
Fixes: c83b8fab06fc ("bridge: Restart queries when last querier expires") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When the commit below was introduced it changed two visible things:
- the skb was no longer passed through the protocol handlers with the
original device
- the skb was passed up the stack with skb->dev = bridge
The first change broke af_packet sockets on bridge ports. For example we
use them for hostapd which listens for ETH_P_PAE packets on the ports.
We discussed two possible fixes:
- create a clone and pass it through NF_HOOK(), act on the original skb
based on the result
- somehow signal to the caller from the okfn() that it was called,
meaning the skb is ok to be passed, which this patch is trying to
implement via returning 1 from the bridge link-local okfn()
Note that we rely on the fact that NF_QUEUE/STOLEN would return 0 and
drop/error would return < 0 thus the okfn() is called only when the
return was 1, so we signal to the caller that it was called by preserving
the return value from nf_hook().
Fixes: 8626c56c8279 ("bridge: fix potential use-after-free when hook returns QUEUE or STOLEN verdict") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Fix this by sanitizing arg before using it to index dev_lec.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When a bond is enslaved to another bond, bond_netdev_event() only
handles the event as if the bond is a master, and skips treating the
bond as a slave.
This leads to a refcount leak on the slave, since we don't remove the
adjacency to its master and the master holds a reference on the slave.
Reproducer:
ip link add bondL type bond
ip link add bondU type bond
ip link set bondL master bondU
ip link del bondL
No "Fixes:" tag, this code is older than git history.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We didn't recover permission field correctly after sudden power-cut,
the reason is in setattr we didn't add inode into global dirty list
once i_mode is changed, so latter checkpoint triggered by fsync will
not flush last i_mode into disk, result in this problem, fix it.
Reported-by: Seulbae Kim <seulbae@gatech.edu> Signed-off-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
rxrpc_disconnect_client_call() reads the call's connection ID protocol
value (call->cid) as part of that function's variable declarations. This
is bad because it's not inside the locked section and so may race with
someone granting use of the channel to the call.
This manifests as an assertion failure (see below) where the call in the
presumed channel (0 because call->cid wasn't set when we read it) doesn't
match the call attached to the channel we were actually granted (if 1, 2 or
3).
Fix this by moving the read and dependent calculations inside of the
channel_lock section. Also, only set the channel number and pointer
variables if cid is not zero (ie. unset).
This problem can be induced by injecting an occasional error in
rxrpc_wait_for_channel() before the call to schedule().
Make two further changes also:
(1) Add a trace for wait failure in rxrpc_connect_call().
(2) Drop channel_lock before BUG'ing in the case of the assertion failure.
Fixes: 45025bceef17 ("rxrpc: Improve management and caching of client connection objects") Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Gigabyte X299 DESIGNARE EX motherboard has one PCIe root port that is
connected to an Alpine Ridge Thunderbolt controller. This port has slot
implemented bit set in the config space but other than that it is not
hotplug capable in the sense we are expecting in Linux (it has
dev->is_hotplug_bridge set to 0):
This system is using ACPI based hotplug to notify the OS that it needs to
rescan the PCI bus (ACPI hotplug).
If there is nothing connected in any of the Thunderbolt ports the root port
will not have any runtime PM active children and is thus automatically
runtime suspended pretty soon after boot by PCI PM core. Now, when a
device is connected the BIOS SMI handler responsible for enumerating newly
added devices is not able to find anything because the port is in D3.
Prevent this from happening by blacklisting PCI power management of this
particular Gigabyte system.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=202031 Reported-by: Kedar A Dongre <kedar.a.dongre@intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
scsi_device_quiesce() and scsi_device_resume() are called during
system-wide suspend and resume. scsi_device_quiesce() only succeeds for
SCSI devices that are in one of the RUNNING, OFFLINE or TRANSPORT_OFFLINE
states (see also scsi_set_device_state()). This patch avoids that the
following warning is triggered when resuming a system for which quiescing a
SCSI device failed:
Cc: Przemek Socha <soprwa@gmail.com> Reported-by: Przemek Socha <soprwa@gmail.com> Fixes: 3a0a529971ec ("block, scsi: Make SCSI quiesce and resume work reliably") # v4.15 Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
redundant copy_from_user in rds_sendmsg system call expose rds
to issue where rds_rdma_extra_size walk the rds iovec and and
calculate the number pf pages (sgs) it need to add to the tail of
rds message and later rds_cmsg_rdma_args copy the rds iovec again
and re calculate the same number and get different result causing
WARN_ON in rds_message_alloc_sgs.
fix this by doing the copy_from_user only once per rds_sendmsg
system call.
There are systems in which non-wakeup GPEs fire during the "noirq"
suspend stage of suspending devices and that effectively prevents the
system that tries to suspend to idle from entering any low-power
state at all. If the offending GPE fires regularly and often enough,
the system appears to be suspended, but in fact it is in a tight loop
over "noirq" suspend and "noirq" resume of devices all the time.
To prevent that from happening, disable all non-wakeup GPEs except
for the EC GPE for suspend-to-idle (the EC GPE is special, because
on some systems it has to be enabled for power button wakeup events
to be generated as expected).
Fixes: 147a7d9d25ca (ACPI / PM: Do not reconfigure GPEs for suspend-to-idle) Link: https://bugzilla.kernel.org/show_bug.cgi?id=201987 Reported-by: Zhang Rui <rui.zhang@intel.com> Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> Tested-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This patch solves bug 200501 'Only 2 of 4 speakers playing sound.'
It enables the front speakers on Huawei Matebook X Pro laptops.
These laptops come with Dolby Atmos sound system and these pins
configuration enables the front speakers.
ttm_bo_glob and ttm_mem_glob are defined as structure instance, while
not allocated by kzalloc, so kfree should not be invoked to release
them anymore. Otherwise, it will cause the following kernel BUG when
unloading amdgpu module
The Image Signal Processor found on Cherry Trail devices is brought up in
D0 state on devices which have camera sensors attached to it. The ISP will
not enter D3 state again without some massaging of its registers beforehand
and the ISP not being in D3 state blocks the SoC from entering S0ix modes.
There was a driver for the ISP in drivers/staging but that got removed
again because it never worked. It does not seem likely that a real
driver for the ISP will be added to the mainline kernel anytime soon.
This commit adds a dummy driver which contains the necessary magic from
the staging driver to powerdown the ISP, so that Cherry Trail devices where
the ISP is used will properly use S0ix modes when suspended.
Together with other recent S0ix related fixes this allows S0ix modes to
be entered on e.g. a Chuwi Hi8 Pro and a HP x2 210.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=196915 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
During recover, we will try to create new dentries for inodes with
dentry_mark. But if the parent is missing (e.g. killed by fsck),
recover will break. But those recovered dirty pages are not cleanup.
This will hit f2fs_bug_on:
Fix crash caused by NULL pointer dereference when debugfs functions
le_max_key_read, le_max_key_size_write, le_min_key_size_read or
le_min_key_size_write and Bluetooth adapter was powered off.
Fix is to move max_key_size and min_key_size from smp_dev to hci_dev.
At the same time they were renamed to le_max_key_size and
le_min_key_size.
MIXER on Exynos5 SoCs uses different synchronisation method than Exynos4
to update internal state (shadow registers).
Apparently the driver implements it incorrectly. The rule should be
as follows:
- do not request updating registers until previous request was finished,
ie. MXR_CFG_LAYER_UPDATE_COUNT must be 0.
- before setting registers synchronisation on VSYNC should be turned off,
ie. MXR_STATUS_SYNC_ENABLE should be reset,
- after finishing MXR_STATUS_SYNC_ENABLE should be set again.
The patch hopefully implements it correctly.
Below sample kernel log from page fault caused by the bug:
[ 25.670038] exynos-sysmmu 14650000.sysmmu: 14450000.mixer: PAGE FAULT occurred at 0x2247b800
[ 25.677888] ------------[ cut here ]------------
[ 25.682164] kernel BUG at ../drivers/iommu/exynos-iommu.c:450!
[ 25.687971] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
[ 25.693778] Modules linked in:
[ 25.696816] CPU: 5 PID: 1553 Comm: fb-release_test Not tainted 5.0.0-rc7-01157-g5f86b1566bdd #136
[ 25.705646] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 25.711710] PC is at exynos_sysmmu_irq+0x1c0/0x264
[ 25.716470] LR is at lock_is_held_type+0x44/0x64
v2: added missing MXR_CFG_LAYER_UPDATE bit setting in mixer_enable_sync
Reported-by: Marian Mihailescu <mihailescu2m@gmail.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Lockdep warns that prepare_lock and genpd->mlock can cause a deadlock
the deadlock scenario is like following:
First thread is probing cs2000
cs2000_probe()
clk_register()
__clk_core_init()
clk_prepare_lock() ----> acquires prepare_lock
cs2000_recalc_rate()
i2c_smbus_read_byte_data()
rcar_i2c_master_xfer()
dma_request_chan()
rcar_dmac_of_xlate()
rcar_dmac_alloc_chan_resources()
pm_runtime_get_sync()
__pm_runtime_resume()
rpm_resume()
rpm_callback()
genpd_runtime_resume() ----> acquires genpd->mlock
Second thread is attaching any device to the same PM domain
genpd_add_device()
genpd_lock() ----> acquires genpd->mlock
cpg_mssr_attach_dev()
of_clk_get_from_provider()
__of_clk_get_from_provider()
__clk_create_clk()
clk_prepare_lock() ----> acquires prepare_lock
Since currently no PM provider access genpd's critical section
in .attach_dev, and .detach_dev callbacks, so there is no need to protect
these two callbacks with genpd->mlock.
This patch avoids a potential deadlock by moving out .attach_dev and .detach_dev
from genpd->mlock, so that genpd->mlock won't be held when prepare_lock is acquired
in .attach_dev and .detach_dev
Signed-off-by: Jiada Wang <jiada_wang@mentor.com> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When commit 8661423eea1a ("ACPI / utils: Add new acpi_dev_present
helper") introduced acpi_dev_present(), it missed the fact that
bus_find_device() took a reference on the device found by it and
the callers of acpi_dev_present() don't drop that reference.
Drop the reference on the device in acpi_dev_present().
Fixes: 8661423eea1a ("ACPI / utils: Add new acpi_dev_present helper") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When admin calls "reboot -f" - i.e., does a hard system reboot by
directly calling reboot(2) - ext4 filesystem mounted with errors=panic
can panic the system. This happens because the underlying device gets
disabled without unmounting the filesystem and thus some syscall running
in parallel to reboot(2) can result in the filesystem getting IO errors.
This is somewhat surprising to the users so try improve the behavior by
switching to errors=remount-ro behavior when the system is running
reboot(2).
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A bugfix just broke compilation of appletalk when CONFIG_SYSCTL
is disabled:
In file included from net/appletalk/ddp.c:65:
net/appletalk/ddp.c: In function 'atalk_init':
include/linux/atalk.h:164:34: error: expected expression before 'do'
#define atalk_register_sysctl() do { } while(0)
^~
net/appletalk/ddp.c:1934:7: note: in expansion of macro 'atalk_register_sysctl'
rc = atalk_register_sysctl();
This is easier to avoid by using conventional inline functions
as stubs rather than macros. The header already has inline
functions for other purposes, so I'm changing over all the
macros for consistency.
Fixes: 6377f787aeb9 ("appletalk: Fix use-after-free in atalk_proc_exit") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We found a race condition in the DMA init sequence that hits if the
PHY already has link up during stmmac_hw_setup. Since the ring length
was programmed after enabling the RX path, we might receive a packet
before the correct ring length is programmed. When that happened we
could not get reliable interrupts for DMA RX and the MTL complained
about RX FIFO overrun.
Signed-off-by: Lars Persson <larper@axis.com> Cc: stable@vger.kernel.org # 4.14.x Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Jose Abreu <joabreu@synopsys.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There's a XFS on dm-crypt deadlock, recursing back to itself due to the
crypto subsystems use of GFP_KERNEL, reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=200835
* dm-crypt calls crypt_convert in xts mode
* init_crypt from xts.c calls kmalloc(GFP_KERNEL)
* kmalloc(GFP_KERNEL) recurses into the XFS filesystem, the filesystem
tries to submit some bios and wait for them, causing a deadlock
Fix this by updating both the DM crypt and integrity targets to no
longer use the CRYPTO_TFM_REQ_MAY_SLEEP flag, which will change the
crypto allocations from GFP_KERNEL to GFP_ATOMIC, therefore they can't
recurse into a filesystem. A GFP_ATOMIC allocation can fail, but
init_crypt() in xts.c handles the allocation failure gracefully - it
will fall back to preallocated buffer if the allocation fails.
The crypto API maintainer says that the crypto API only needs to
allocate memory when dealing with unaligned buffers and therefore
turning CRYPTO_TFM_REQ_MAY_SLEEP off is safe (see this discussion:
https://www.redhat.com/archives/dm-devel/2018-August/msg00195.html )
syzkaller was able to generate the following UAF in bpf:
BUG: KASAN: use-after-free in lookup_last fs/namei.c:2269 [inline]
BUG: KASAN: use-after-free in path_lookupat.isra.43+0x9f8/0xc00 fs/namei.c:2318
Read of size 1 at addr ffff8801c4865c47 by task syz-executor2/9423
In this scenario path lookup under RCU is racing with the final
unlink in case of symlinks. As Linus puts it in his analysis:
[...] We actually RCU-delay the inode freeing itself, but
when we do the final iput(), the "evict()" function is called
synchronously. Now, the simple fix would seem to just RCU-delay
the kfree() of the symlink data in bpf_evict_inode(). Maybe
that's the right thing to do. [...]
Al suggested to piggy-back on the ->destroy_inode() callback in
order to implement RCU deferral there which can then kfree() the
inode->i_link eventually right before putting inode back into
inode cache. By reusing free_inode_nonrcu() from there we can
avoid the need for our own inode cache and just reuse generic
one as we currently do.
And in-fact on top of all this we should just get rid of the
bpf_evict_inode() entirely. This means truncate_inode_pages_final()
and clear_inode() will then simply be called by the fs core via
evict(). Dropping the reference should really only be done when
inode is unhashed and nothing reachable anymore, so it's better
also moved into the final ->destroy_inode() callback.
Fixes: 0f98621bef5d ("bpf, inode: add support for symlinks and fix mtime/ctime") Reported-by: syzbot+fb731ca573367b7f6564@syzkaller.appspotmail.com Reported-by: syzbot+a13e5ead792d6df37818@syzkaller.appspotmail.com Reported-by: syzbot+7a8ba368b47fdefca61e@syzkaller.appspotmail.com Suggested-by: Al Viro <viro@zeniv.linux.org.uk> Analyzed-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: Al Viro <viro@zeniv.linux.org.uk> Link: https://lore.kernel.org/lkml/0000000000006946d2057bbd0eef@google.com/T/ Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Use offsetof() to calculate offset of a field to take advantage of
compiler built-in version when possible, and avoid UBSAN warning when
compiling with Clang:
UBSAN: Undefined behaviour in mm/swapfile.c:3010:38
member access within null pointer of type 'union swap_header'
CPU: 6 PID: 1833 Comm: swapon Tainted: G S 4.19.23 #43
Call trace:
dump_backtrace+0x0/0x194
show_stack+0x20/0x2c
__dump_stack+0x20/0x28
dump_stack+0x70/0x94
ubsan_epilogue+0x14/0x44
ubsan_type_mismatch_common+0xf4/0xfc
__ubsan_handle_type_mismatch_v1+0x34/0x54
__se_sys_swapon+0x654/0x1084
__arm64_sys_swapon+0x1c/0x24
el0_svc_common+0xa8/0x150
el0_svc_compat_handler+0x2c/0x38
el0_svc_compat+0x8/0x18
Link: http://lkml.kernel.org/r/20190312081902.223764-1-pihsun@chromium.org Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
fls counts bits starting from 1 to 32 (returns 0 for zero argument). If
we add 1 we shift right one bit more and loose precision from divisor,
what cause function incorect results with some numbers.
Corrected code was tested in user-space, see bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=202391
Memory state around the buggy address: ffff8881f41fe480: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc ffff8881f41fe500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8881f41fe580: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff8881f41fe600: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb ffff8881f41fe680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
It should check the return value of atalk_proc_init fails,
otherwise atalk_exit will trgger use-after-free in pde_subdir_find
while unload the module.This patch fix error cleanup path of atalk_init
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Signed-off-by: Kevin Wang <kevin1.wang@amd.com> Reviewed-by: Oak Zeng <Oak.Zeng@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When running kprobe on -rt kernel, the below bug is caught:
|BUG: sleeping function called from invalid context at kernel/locking/rtmutex.c:931
|in_atomic(): 1, irqs_disabled(): 128, pid: 14, name: migration/0
|Preemption disabled at:[<802f2b98>] cpu_stopper_thread+0xc0/0x140
|CPU: 0 PID: 14 Comm: migration/0 Tainted: G O 4.8.3-rt2 #1
|Hardware name: Freescale LS1021A
|[<8025a43c>] (___might_sleep)
|[<80b5b324>] (rt_spin_lock)
|[<80b5c31c>] (__patch_text_real)
|[<80b5c3ac>] (patch_text_stop_machine)
|[<802f2920>] (multi_cpu_stop)
Since patch_text_stop_machine() is called in stop_machine() which
disables IRQ, sleepable lock should be not used in this atomic context,
so replace patch_lock to raw lock.
Signed-off-by: Yang Shi <yang.shi@linaro.org> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On some Samsung hardware, it is necessary to clear events accumulated by
the EC during sleep. These ECs stop reporting GPEs until they are manually
polled, if too many events are accumulated.
Thus the CLEAR_ON_RESUME quirk is introduced to send EC query commands
unconditionally after resume to clear all the EC query events on those
platforms.
Later, commit 4c237371f290 ("ACPI / EC: Remove old CLEAR_ON_RESUME quirk")
removes the CLEAR_ON_RESUME quirk because we thought the new EC IRQ
polling logic should handle this case.
Now it has been proved that the EC IRQ Polling logic does not fix the
issue actually because we got regression report on these Samsung
platforms after removing the quirk.
Thus revert commit 4c237371f290 ("ACPI / EC: Remove old CLEAR_ON_RESUME
quirk") to introduce back the Samsung quirk in this patch.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=44161 Tested-by: Ortwin Glück <odi@odi.ch> Tested-by: Francisco Cribari <cribari@gmail.com> Tested-by: Balazs Varga <balazs4web@gmail.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Clients may submit a new requests from the completion callback
context. The driver was not prepared to receive a request in this
state because it already held the request queue lock and a recursive
lock error is triggered.
Now all completions are queued up until we are ready to drop the queue
lock and then delivered.
The fault was triggered by TCP over an IPsec connection in the LTP
test suite:
LTP: starting tcp4_ipsec02 (tcp_ipsec.sh -p ah -m transport -s "100 1000 65535")
BUG: spinlock recursion on CPU#1, genload/943
lock: 0xbf3c3094, .magic: dead4ead, .owner: genload/943, .owner_cpu: 1
CPU: 1 PID: 943 Comm: genload Tainted: G O 4.9.62-axis5-devel #6
Hardware name: Axis ARTPEC-6 Platform
(unwind_backtrace) from [<8010d134>] (show_stack+0x18/0x1c)
(show_stack) from [<803a289c>] (dump_stack+0x84/0x98)
(dump_stack) from [<8016e164>] (do_raw_spin_lock+0x124/0x128)
(do_raw_spin_lock) from [<804de1a4>] (artpec6_crypto_submit+0x2c/0xa0)
(artpec6_crypto_submit) from [<804def38>] (artpec6_crypto_prepare_submit_hash+0xd0/0x54c)
(artpec6_crypto_prepare_submit_hash) from [<7f3165f0>] (ah_output+0x2a4/0x3dc [ah4])
(ah_output [ah4]) from [<805df9bc>] (xfrm_output_resume+0x178/0x4a4)
(xfrm_output_resume) from [<805d283c>] (xfrm4_output+0xac/0xbc)
(xfrm4_output) from [<80587928>] (ip_queue_xmit+0x140/0x3b4)
(ip_queue_xmit) from [<805a13b4>] (tcp_transmit_skb+0x4c4/0x95c)
(tcp_transmit_skb) from [<8059f218>] (tcp_rcv_state_process+0xdf4/0xdfc)
(tcp_rcv_state_process) from [<805a7530>] (tcp_v4_do_rcv+0x64/0x1ac)
(tcp_v4_do_rcv) from [<805a9724>] (tcp_v4_rcv+0xa34/0xb74)
(tcp_v4_rcv) from [<80581d34>] (ip_local_deliver_finish+0x78/0x2b0)
(ip_local_deliver_finish) from [<8058259c>] (ip_local_deliver+0xe4/0x104)
(ip_local_deliver) from [<805d23ec>] (xfrm4_transport_finish+0xf4/0x144)
(xfrm4_transport_finish) from [<805df564>] (xfrm_input+0x4f4/0x74c)
(xfrm_input) from [<804de420>] (artpec6_crypto_task+0x208/0x38c)
(artpec6_crypto_task) from [<801271b0>] (tasklet_action+0x60/0xec)
(tasklet_action) from [<801266d4>] (__do_softirq+0xcc/0x3a4)
(__do_softirq) from [<80126d20>] (irq_exit+0xf4/0x15c)
(irq_exit) from [<801741e8>] (__handle_domain_irq+0x68/0xbc)
(__handle_domain_irq) from [<801014f0>] (gic_handle_irq+0x50/0x94)
(gic_handle_irq) from [<80657370>] (__irq_usr+0x50/0x80)
Signed-off-by: Lars Persson <larper@axis.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Move mipi_dsi_dcs_set_display_off() from innolux_panel_disable()
to innolux_panel_unprepare(), so they are consistent with
innolux_panel_enable() and innolux_panel_prepare().
This also fixes some mode check and irq timeout issue in MTK dsi code.
Since some dsi code (e.g. mtk_dsi) have following call trace:
1. drm_panel_disable(), which calls innolux_panel_disable()
2. switch to cmd mode
3. drm_panel_unprepare(), which calls innolux_panel_unprepare()
However, mtk_dsi needs to be in cmd mode to be able to send commands
(e.g. mipi_dsi_dcs_set_display_off() and mipi_dsi_dcs_enter_sleep_mode()),
so we need these functions to be called after the switch to cmd mode happens,
i.e. in innolux_panel_unprepare.
Signed-off-by: Hsin-Yi, Wang <hsinyi@chromium.org> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190109065922.231753-1-hsinyi@chromium.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Introduce lkdtm tests for NULL pointer dereference: check access or exec
at NULL address, since these errors tend to be reported differently from
the general fault error text. For example from x86:
pr_alert("BUG: unable to handle kernel %s at %px\n",
address < PAGE_SIZE ? "NULL pointer dereference" : "paging request",
(void *)address);
Today, when doing a lkdtm test before the readiness of the
random generator, (ptrval) is printed instead of the address
at which it perform the fault:
[ 1597.337030] lkdtm: Performing direct entry EXEC_USERSPACE
[ 1597.337142] lkdtm: attempting ok execution at (ptrval)
[ 1597.337398] lkdtm: attempting bad execution at (ptrval)
[ 1597.337460] kernel tried to execute user page (77858000) -exploit attempt? (uid: 0)
[ 1597.344769] Unable to handle kernel paging request for instruction fetch
[ 1597.351392] Faulting instruction address: 0x77858000
[ 1597.356312] Oops: Kernel access of bad area, sig: 11 [#1]
If the lkdtm test is done later on, it prints an hashed address.
In both cases this is pointless. The purpose of the test is to
ensure the kernel generates an Oops at the expected address,
so real addresses needs to be printed. This patch fixes that.
This fixes splats like the one below if CONFIG_DEBUG_ATOMIC_SLEEP=y
and machine (Tegra30) booted with SMP=n or all secondary CPU's are put
offline. Locking isn't needed because it protects atomic operation.
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:254
in_atomic(): 1, irqs_disabled(): 128, pid: 0, name: swapper/0
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G C 4.18.0-next-20180821-00180-gc3ebb6544e44-dirty #823
Hardware name: NVIDIA Tegra SoC (Flattened Device Tree)
[<c01134f4>] (unwind_backtrace) from [<c010db2c>] (show_stack+0x20/0x24)
[<c010db2c>] (show_stack) from [<c0bd0f3c>] (dump_stack+0x94/0xa8)
[<c0bd0f3c>] (dump_stack) from [<c0151df8>] (___might_sleep+0x13c/0x174)
[<c0151df8>] (___might_sleep) from [<c0151ea0>] (__might_sleep+0x70/0xa8)
[<c0151ea0>] (__might_sleep) from [<c0bec2b8>] (mutex_lock+0x2c/0x70)
[<c0bec2b8>] (mutex_lock) from [<c0589844>] (tegra_powergate_is_powered+0x44/0xa8)
[<c0589844>] (tegra_powergate_is_powered) from [<c0581a60>] (tegra30_cpu_rail_off_ready+0x30/0x74)
[<c0581a60>] (tegra30_cpu_rail_off_ready) from [<c0122244>] (tegra30_idle_lp2+0xa0/0x108)
[<c0122244>] (tegra30_idle_lp2) from [<c0853438>] (cpuidle_enter_state+0x140/0x540)
[<c0853438>] (cpuidle_enter_state) from [<c08538a4>] (cpuidle_enter+0x40/0x4c)
[<c08538a4>] (cpuidle_enter) from [<c01595e0>] (call_cpuidle+0x30/0x48)
[<c01595e0>] (call_cpuidle) from [<c01599f8>] (do_idle+0x238/0x28c)
[<c01599f8>] (do_idle) from [<c0159d28>] (cpu_startup_entry+0x28/0x2c)
[<c0159d28>] (cpu_startup_entry) from [<c0be76c8>] (rest_init+0xd8/0xdc)
[<c0be76c8>] (rest_init) from [<c1200f50>] (start_kernel+0x41c/0x430)
Commit 57384592c433 ("iommu/vt-d: Store bus information in RMRR PCI
device path") changed the type of the path data, however, the change in
path type was not reflected in size calculations. Update to use the
correct type and prevent a buffer overflow.
This bug manifests in systems with deep PCI hierarchies, and can lead to
an overflow of the static allocated buffer (dmar_pci_notify_info_buf),
or can lead to overflow of slab-allocated data.
The SHA512 code we adopted from the OpenSSL project uses a rather
peculiar way to take the address of the round constant table: it
takes the address of the sha256_block_data_order() routine, and
substracts a constant known quantity to arrive at the base of the
table, which is emitted by the same assembler code right before
the routine's entry point.
However, recent versions of binutils have helpfully changed the
behavior of references emitted via an ADR instruction when running
in Thumb2 mode: it now takes the Thumb execution mode bit into
account, which is bit 0 af the address. This means the produced
table address also has bit 0 set, and so we end up with an address
value pointing 1 byte past the start of the table, which results
in crashes such as
Unable to handle kernel paging request at virtual address bf825000
pgd = 42f44b11
[bf825000] *pgd=80000040206003, *pmd=5f1bd003, *pte=00000000
Internal error: Oops: 207 [#1] PREEMPT SMP THUMB2
Modules linked in: sha256_arm(+) sha1_arm_ce sha1_arm ...
CPU: 7 PID: 396 Comm: cryptomgr_test Not tainted 5.0.0-rc6+ #144
Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
PC is at sha256_block_data_order+0xaaa/0xb30 [sha256_arm]
LR is at __this_module+0x17fd/0xffffe800 [sha256_arm]
pc : [<bf820bca>] lr : [<bf824ffd>] psr: 800b0033
sp : ebc8bbe8 ip : faaabe1c fp : 2fdd3433
r10: 4c5f1692 r9 : e43037df r8 : b04b0a5a
r7 : c369d722 r6 : 39c3693e r5 : 7a013189 r4 : 1580d26b
r3 : 8762a9b0 r2 : eea9c2cd r1 : 3e9ab536 r0 : 1dea4ae7
Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA Thumb Segment user
Control: 70c5383d Table: 6b8467c0 DAC: dbadc0de
Process cryptomgr_test (pid: 396, stack limit = 0x69e1fe23)
Stack: (0xebc8bbe8 to 0xebc8c000)
...
unwind: Unknown symbol address bf820bca
unwind: Index not found bf820bca
Code: 441a ea80 40f9 440a (f85e) 3b04
---[ end trace e560cce92700ef8a ]---
Given that this affects older kernels as well, in case they are built
with a recent toolchain, apply a minimal backportable fix, which is
to emit another non-code label at the start of the routine, and
reference that instead. (This is similar to the current upstream state
of this file in OpenSSL)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The SHA256 code we adopted from the OpenSSL project uses a rather
peculiar way to take the address of the round constant table: it
takes the address of the sha256_block_data_order() routine, and
substracts a constant known quantity to arrive at the base of the
table, which is emitted by the same assembler code right before
the routine's entry point.
However, recent versions of binutils have helpfully changed the
behavior of references emitted via an ADR instruction when running
in Thumb2 mode: it now takes the Thumb execution mode bit into
account, which is bit 0 af the address. This means the produced
table address also has bit 0 set, and so we end up with an address
value pointing 1 byte past the start of the table, which results
in crashes such as
Unable to handle kernel paging request at virtual address bf825000
pgd = 42f44b11
[bf825000] *pgd=80000040206003, *pmd=5f1bd003, *pte=00000000
Internal error: Oops: 207 [#1] PREEMPT SMP THUMB2
Modules linked in: sha256_arm(+) sha1_arm_ce sha1_arm ...
CPU: 7 PID: 396 Comm: cryptomgr_test Not tainted 5.0.0-rc6+ #144
Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
PC is at sha256_block_data_order+0xaaa/0xb30 [sha256_arm]
LR is at __this_module+0x17fd/0xffffe800 [sha256_arm]
pc : [<bf820bca>] lr : [<bf824ffd>] psr: 800b0033
sp : ebc8bbe8 ip : faaabe1c fp : 2fdd3433
r10: 4c5f1692 r9 : e43037df r8 : b04b0a5a
r7 : c369d722 r6 : 39c3693e r5 : 7a013189 r4 : 1580d26b
r3 : 8762a9b0 r2 : eea9c2cd r1 : 3e9ab536 r0 : 1dea4ae7
Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA Thumb Segment user
Control: 70c5383d Table: 6b8467c0 DAC: dbadc0de
Process cryptomgr_test (pid: 396, stack limit = 0x69e1fe23)
Stack: (0xebc8bbe8 to 0xebc8c000)
...
unwind: Unknown symbol address bf820bca
unwind: Index not found bf820bca
Code: 441a ea80 40f9 440a (f85e) 3b04
---[ end trace e560cce92700ef8a ]---
Given that this affects older kernels as well, in case they are built
with a recent toolchain, apply a minimal backportable fix, which is
to emit another non-code label at the start of the routine, and
reference that instead. (This is similar to the current upstream state
of this file in OpenSSL)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In cases where queryinfo fails, we have cases in cifs (vers=1.0)
where with backupuid mounts we retry the query info with findfirst.
This doesn't work to some NetApp servers which don't support
WindowsXP (and later) infolevel 261 (SMB_FIND_FILE_ID_FULL_DIR_INFO)
so in this case use other info levels (in this case it will usually
be level 257, SMB_FIND_FILE_DIRECTORY_INFO).
(Also fixes some indentation)
See kernel bugzilla 201435
Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A VMEnter that VMFails (as opposed to VMExits) does not touch host
state beyond registers that are explicitly noted in the VMFail path,
e.g. EFLAGS. Host state does not need to be loaded because VMFail
is only signaled for consistency checks that occur before the CPU
starts to load guest state, i.e. there is no need to restore any
state as nothing has been modified. But in the case where a VMFail
is detected by hardware and not by KVM (due to deferring consistency
checks to hardware), KVM has already loaded some amount of guest
state. Luckily, "loaded" only means loaded to KVM's software model,
i.e. vmcs01 has not been modified. So, unwind our software model to
the pre-VMEntry host state.
Not restoring host state in this VMFail path leads to a variety of
failures because we end up with stale data in vcpu->arch, e.g. CR0,
CR4, EFER, etc... will all be out of sync relative to vmcs01. Any
significant delta in the stale data is all but guaranteed to crash
L1, e.g. emulation of SMEP, SMAP, UMIP, WP, etc... will be wrong.
An alternative to this "soft" reload would be to load host state from
vmcs12 as if we triggered a VMExit (as opposed to VMFail), but that is
wildly inconsistent with respect to the VMX architecture, e.g. an L1
VMM with separate VMExit and VMFail paths would explode.
Note that this approach does not mean KVM is 100% accurate with
respect to VMX hardware behavior, even at an architectural level
(the exact order of consistency checks is microarchitecture specific).
But 100% emulation accuracy isn't the goal (with this patch), rather
the goal is to be consistent in the information delivered to L1, e.g.
a VMExit should not fall-through VMENTER, and a VMFail should not jump
to HOST_RIP.
This technically reverts commit "5af4157388ad (KVM: nVMX: Fix mmu
context after VMLAUNCH/VMRESUME failure)", but retains the core
aspects of that patch, just in an open coded form due to the need to
pull state from vmcs01 instead of vmcs12. Restoring host state
resolves a variety of issues introduced by commit "4f350c6dbcb9
(kvm: nVMX: Handle deferred early VMLAUNCH/VMRESUME failure properly)",
which remedied the incorrect behavior of treating VMFail like VMExit
but in doing so neglected to restore arch state that had been modified
prior to attempting nested VMEnter.
A sample failure that occurs due to stale vcpu.arch state is a fault
of some form while emulating an LGDT (due to emulated UMIP) from L1
after a failed VMEntry to L3, in this case when running the KVM unit
test test_tpr_threshold_values in L1. L0 also hits a WARN in this
case due to a stale arch.cr4.UMIP.
L1:
BUG: unable to handle kernel paging request at ffffc90000663b9e
PGD 276512067 P4D 276512067 PUD 276513067 PMD 274efa067 PTE 8000000271de2163
Oops: 0009 [#1] SMP
CPU: 5 PID: 12495 Comm: qemu-system-x86 Tainted: G W 4.18.0-rc2+ #2
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:native_load_gdt+0x0/0x10
On Apple machines, plugging-in or unplugging the power triggers a GPE
for the EC. Since these machines expose an SBS device, this GPE ends
up triggering the acpi_sbs_callback(). This in turn tries to get the
status of the SBS charger. However, on MBP13,* and MBP14,* machines,
performing the smbus-read operation to get the charger's status triggers
the EC's GPE again. The result is an endless re-triggering and handling
of that GPE, consuming significant CPU resources (> 50% in irq).
In the end this is quite similar to commit 3031cddea633 (ACPI / SBS:
Don't assume the existence of an SBS charger), except that on the above
machines a status of all 1's is returned. And like there, we just want
ignore the charger here.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=198169 Signed-off-by: Ronald Tschalär <ronald@innovation.ch> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Because it detects 'w83627hf.656' as another vhci_hcd controller,
and then fails to be able to talk to it.
Note: this doesn't actually fix usbip's support for multiple
controllers... that's still broken for other reasons
("vhci_hcd.0" is hardcoded in a string macro), but is enough to
actually make it work on the above machine.
See also:
https://bugzilla.redhat.com/show_bug.cgi?id=1631148
"S3C2410 PM Suspend Memory CRC" feature (controlled by
SAMSUNG_PM_CHECK config option) is incompatible with highmem
(uses phys_to_virt() instead of proper mapping) which is used by
the majority of Exynos boards. The issue manifests itself in OOPS
on affected boards, i.e. on Odroid-U3 I got the following one:
Unable to handle kernel paging request at virtual address f0000000
pgd = 1c0f9bb4
[f0000000] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[<c0458034>] (crc32_le) from [<c0121f8c>] (s3c_pm_makecheck+0x34/0x54)
[<c0121f8c>] (s3c_pm_makecheck) from [<c0121efc>] (s3c_pm_run_res+0x74/0x8c)
[<c0121efc>] (s3c_pm_run_res) from [<c0121ecc>] (s3c_pm_run_res+0x44/0x8c)
[<c0121ecc>] (s3c_pm_run_res) from [<c01210b8>] (exynos_suspend_enter+0x64/0x148)
[<c01210b8>] (exynos_suspend_enter) from [<c018893c>] (suspend_devices_and_enter+0x9ec/0xe74)
[<c018893c>] (suspend_devices_and_enter) from [<c0189534>] (pm_suspend+0x770/0xc04)
[<c0189534>] (pm_suspend) from [<c0186ce8>] (state_store+0x6c/0xcc)
[<c0186ce8>] (state_store) from [<c09db434>] (kobj_attr_store+0x14/0x20)
[<c09db434>] (kobj_attr_store) from [<c02fa63c>] (sysfs_kf_write+0x4c/0x50)
[<c02fa63c>] (sysfs_kf_write) from [<c02f97a4>] (kernfs_fop_write+0xfc/0x1e4)
[<c02f97a4>] (kernfs_fop_write) from [<c027b198>] (__vfs_write+0x2c/0x140)
[<c027b198>] (__vfs_write) from [<c027b418>] (vfs_write+0xa4/0x160)
[<c027b418>] (vfs_write) from [<c027b5d8>] (ksys_write+0x40/0x8c)
[<c027b5d8>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
Add PLAT_S3C24XX, ARCH_S3C64XX and ARCH_S5PV210 dependencies to
SAMSUNG_PM_CHECK config option to hide it on Exynos platforms.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A particular touchpad (SIPODEV SP1064) refuses to supply the HID
descriptors. This patch provides the framework for overriding these
descriptors based on DMI data. It also includes the descriptors for
said touchpad, which were extracted by listening to the traffic of the
windows filter driver, as well as the DMI data for the laptops known
to use this device.
If au0828_analog_register fails, the dev is kfree'd and then flow
jumps to done, which can call au0828_usb_disconnect. Since all USB
error codes are negative, au0828_usb_disconnect will be called. The
problem is au0828_usb_disconnect uses dev, if dev is NULL then there
is immediate oops encountered.
When a PRRN event is received we are already running in a worker
thread. Instead of spawning off another worker thread on the prrn_work
workqueue to handle the PRRN event we can just call the PRRN handler
routine directly.
With this update we can also pass the scope variable for the PRRN
event directly to the handler instead of it being a global variable.
This patch fixes the following oops mnessage we are seeing in PRRN testing:
When console device is rebinded, console_setup() is called again.
But marking it as __init means that function will be clear after boot is
complete. If console device is binded again console_setup() is not found
and error "Unable to handle kernel paging request at virtual address"
is reported.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>