David Ahern [Tue, 2 Apr 2019 21:11:54 +0000 (14:11 -0700)]
ipv4: Update fib_table_lookup tracepoint to take common nexthop
Update fib_table_lookup tracepoint to take a fib_nh_common struct and
dump the v6 gateway address if the nexthop uses it.
Over the years saddr has not proven useful and the output of the
tracepoint produces very long lines. Since saddr is not part of
fib_nh_common, drop it. If it needs to be added later, fib_nh which
contains saddr can be obtained from a fib_nh_common via container_of.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: fix autoneg mismatch case in genphy_read_status
The original patch didn't consider the case that autoneg process
finishes successfully but both link partners have no mode in common.
In this case there's no link, nevertheless we may be interested in
what the link partner advertised.
Like phydev->link we set phydev->autoneg_complete in
genphy_update_link() and use the stored value in genphy_read_status().
This way we don't have to read register BMSR again.
Fixes: b6163f194c69 ("net: phy: improve genphy_read_status") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
This series implements the suspend/resume callbacks in the marvell10g
PHY driver.
Thanks,
Antoine
Since v3:
- Use the new phy_set/clear_bits_mmd() instead of phy_modify_mmd().
- Use VEND2.f001.11 to power down the port instead of the per-mode
LPOWER.
Since v2:
- Removed the third patch, setting the PHY in low power by default, as
the change was controversial.
- Rebased on the latest net-next.
Since v1:
- Fixed a mix up in the patches where two implementations of the
suspend/resume callbacks were kept in the driver.
- Rebased on the latest net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Tue, 2 Apr 2019 13:10:29 +0000 (15:10 +0200)]
net: phy: marvell10g: add the suspend/resume callbacks for the 88x2210
When the 88x2110 PHY support was added, the suspend and resume callbacks
were forgotten. This patch adds them to the 88x2110 PHY callback
definition.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the suspend/resume callbacks for Marvell 10G PHYs. The
three PCS (base-t, base-r and 1000base-x) are set in low power (the PCS
are powered down) when the PHY isn't used.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: microchip: mark expected switch fall-through
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/dsa/microchip/ksz9477.c: In function ‘ksz9477_get_interface’:
drivers/net/dsa/microchip/ksz9477.c:1145:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (gbit)
^
drivers/net/dsa/microchip/ksz9477.c:1147:2: note: here
case 0:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warning:
net/rxrpc/local_object.c: In function ‘rxrpc_open_socket’:
net/rxrpc/local_object.c:175:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (ret < 0) {
^
net/rxrpc/local_object.c:184:2: note: here
case AF_INET:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Currently, GCC is expecting to find the fall-through annotations
at the very bottom of the case and on its own line. That's why
I had to add the annotation, although the intentional fall-through
is already mentioned in a few lines above.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Action tunnel_key doesn't have a metadata/tunnel for release(decap) action.
Drivers do not dereference entry->tunnel pointer for that action type, so
this behavior doesn't result in a crash at the moment. However, this needs
to be corrected as a preparation for updating hardware offloads API to not
rely on rtnl lock, for which flow_action code will copy the tunnel data to
temporary buffer to prevent concurrent action overwrite from
invalidating/freeing it.
Fixes: 3a7b68617de7 ("cls_api: add translator to flow_action representation") Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This series improves genphy_c45_read_lpa:
- Use clause 45 standard register / bit to detect link partner autoneg
capability.
- Consider that lpa register values may be invalid if "autoneg complete"
bit isn't set.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Sun, 31 Mar 2019 17:54:07 +0000 (19:54 +0200)]
net: phy: deal properly with autoneg incomplete in genphy_c45_read_lpa
The link partner advertisement registers are not guaranteed to contain
valid values if autoneg is incomplete. Therefore, if
MDIO_AN_STAT1_COMPLETE isn't set, let's clear all link partner
capability bits. This also avoids unnecessary register reads if link
is down and phylib is in polling mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Sun, 31 Mar 2019 17:52:51 +0000 (19:52 +0200)]
net: phy: use c45 standard to detect link partner autoneg capability
Currently mii_lpa_mod_linkmode_lpa_t() checks bit LPA_LPACK to detect
whether link partner supports autoneg. This doesn't work correctly at
least on Aquantia AQCS109 when it negotiates 1000Base-T2 mode.
The "link partner is autoneg-capable" bit as defined by clause 45 is
set however. Better let's switch in general to use the clause 45
standard for link partner autoneg detection.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 2 Apr 2019 20:09:56 +0000 (13:09 -0700)]
Merge branch 'genphy_read_abilities'
Heiner Kallweit says:
====================
net: phy: add and use new function genphy_read_abilities
Similar to genphy_c45_pma_read_abilities() add a function to dynamically
detect the abilities of a Clause 22 PHY. This is mainly copied from
genphy_config_init(). Main benefit is that PHY drivers no longer have
to specify whether they support GBit or not (provided they keep to
the C22 standard).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Wed, 27 Mar 2019 20:59:33 +0000 (21:59 +0100)]
net: phy: use genphy_read_abilities in genphy driver
Currently the genphy driver populates phydev->supported like this:
First all possible feature bits are set, then genphy_config_init()
reads the available features from the chip and remove all unsupported
features from phydev->supported. This can be simplified by using
genphy_read_abilities().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Wed, 27 Mar 2019 20:58:44 +0000 (21:58 +0100)]
net: phy: add genphy_read_abilities
Similar to genphy_c45_pma_read_abilities() add a function to dynamically
detect the abilities of a Clause 22 PHY. This is mainly copied from
genphy_config_init().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Tue, 2 Apr 2019 06:53:14 +0000 (09:53 +0300)]
openvswitch: use after free in __ovs_ct_free_action()
We free "ct_info->ct" and then use it on the next line when we pass it
to nf_ct_destroy_timeout(). This patch swaps the order to avoid the use
after free.
Fixes: 06bd2bdf19d2 ("openvswitch: Add timeout support to ct action") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Yi-Hung Wei <yihung.wei@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Maxwell [Tue, 2 Apr 2019 05:07:56 +0000 (16:07 +1100)]
tg3: allow ethtool -p to work for NICs in down state
Make tg3 behave like other drivers and let "ethtool -p" identify the
NIC even when it's in the DOWN state. Before this patch it would get an
error as follows if the NIC was down:
# ip link set down dev em4
# ethtool -p em4
Cannot identify NIC: Resource temporarily unavailable
With this patch ethtool identify works regardless of whether the NIC is up
or down as it does for other drivers.
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com> Acked-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
macsec: add noinline tag to avoid a frame size warning
seen with debug config:
drivers/net/macsec.c: In function 'dump_secy':
drivers/net/macsec.c:2597: warning: the frame size of 2216 bytes is larger
than 2048 bytes [-Wframe-larger-than=]
just mark it with noinline_for_stack, this is netlink dump code.
v2: use 'static noinline_for_stack int' consistently
Cc: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: Florian Westphal <fw@strlen.de> Reviewed-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
skb->xmit_more hint is now always 0, this switches the sfc driver to
use the netdev_xmit_more helper instead.
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com> Cc: Edward Cree <ecree@solarflare.com> Cc: Bert Kenward <bkenward@solarflare.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
skb->xmit_more hint is now always 0. This switches the mellanox drivers
to the netdev_xmit_more() helper.
Cc: Saeed Mahameed <saeedm@mellanox.com> Cc: Leon Romanovsky <leon@kernel.org> Cc: Boris Pismenny <borisp@mellanox.com> Cc: Ilya Lesokhin <ilyal@mellanox.com> Cc: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
First, the xmit_more flag conceptually doesn't fit into the skb, as
xmit_more is not a property related to the skb.
Its only a hint to the driver that the stack is about to transmit another
packet immediately.
Second, it was only done this way to not have to pass another argument
to ndo_start_xmit().
We can place xmit_more in the softnet data, next to the device recursion.
The recursion counter is already written to on each transmit. The "more"
indicator is placed right next to it.
Drivers can use the netdev_xmit_more() helper instead of skb->xmit_more
to check the "more packets coming" hint.
skb->xmit_more is retained (but always 0) to not cause build breakage.
This change takes care of the simple s/skb->xmit_more/netdev_xmit_more()/
conversions. Remaining drivers are converted in the next patches.
Suggested-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Sun, 31 Mar 2019 15:42:24 +0000 (17:42 +0200)]
net: phy: aquantia: add SGMII statistics
The AQR107 family has SGMII statistics counters. Let's expose them to
ethtool. To interpret the counters correctly one has to be aware that
rx on SGMII side is tx on ethernet side. The counters are populated
by the chip in 100Mbps/1Gbps mode only.
v2:
- add constant AQR107_SGMII_STAT_SZ
- add struct aqr107_priv to be prepared for more private data fields
- let aqr107_get_stat() return U64_MAX in case of an error
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sun, 31 Mar 2019 09:03:02 +0000 (17:03 +0800)]
net: use rcu_dereference_protected to fetch sk_dst_cache in sk_destruct
As Eric noticed, in .sk_destruct, sk->sk_dst_cache update is prevented, and
no barrier is needed for this. So change to use rcu_dereference_protected()
instead of rcu_dereference_check() to fetch sk_dst_cache in there.
v1->v2:
- no change, repost after net-next is open.
Reported-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Sat, 30 Mar 2019 09:22:45 +0000 (10:22 +0100)]
net: phy: improve genphy_read_status
This patch improves few aspects of genphy_read_status():
- Don't initialize lpagb, it's not needed.
- Move initializing phydev->speed et al before the if clause.
- In auto-neg case, skip populating lp_advertising if we
don't have a link. This avoids quite some unnecessary
MDIO reads in case of phylib polling mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
nfp: flower improvement and SFF module EEPROM
The first patch in this series from Pieter improves the
handling of mangle actions in TC flower offload. These
used to be sent down to the driver in groups, but after
Pablo N's patches they are split out causing suboptimal
expression.
The ramaining two patches from Dirk add support for reading
SFF module EEPROM data.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the NSP provides the ability to read from the SFF modules'
EEPROM, we can use this interface to implement the ethtool callback.
If the NSP only provides partial data, we log the event from within
the driver but pass a success code to ethtool to prevent it from
discarding the partial data.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The NSP now provides the ability to read from the SFF module EEPROM.
Note that even if an error occurs, the NSP may still provide some of the
data.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
nfp: flower: reduce action list size by coalescing mangle actions
With the introduction of flow_action_for_each pedit actions are no
longer grouped together, instead pedit actions are broken out per
32 byte word. This results in an inefficient use of the action list
that is pushed to hardware where each 32 byte word becomes its own
action. Therefore we combine groups of 32 byte word before sending
the action list to hardware.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Fri, 29 Mar 2019 20:09:27 +0000 (21:09 +0100)]
net: phy: aquantia: add suspend / resume callbacks for AQR107 family
Add suspend / resume callbacks for AQR107 family. Suspend powers down
the complete chip except MDIO and internal CPU.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
The use of zero-sized array causes undefined behaviour when it is not
the last member in a structure. As it happens to be in this case.
Also, the current code makes use of a language extension to the C90
standard, but the preferred mechanism to declare variable-length
types such as this one is a flexible array member, introduced in
C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last. Which is beneficial
to cultivate a high-quality code.
Fixes: e48f129c2f20 ("[SCSI] cxgb3i: convert cdev->l2opt to use rcu to prevent NULL dereference") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xiaofei Shen [Fri, 29 Mar 2019 05:34:58 +0000 (11:04 +0530)]
net: dsa: read mac address from DT for slave device
Before creating a slave netdevice, get the mac address from DTS and
apply in case it is valid.
Signed-off-by: Xiaofei Shen <xiaofeis@codeaurora.org> Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 1 Apr 2019 10:09:20 +0000 (03:09 -0700)]
tcp: fix tcp_inet6_sk() for 32bit kernels
It turns out that struct ipv6_pinfo is not located as we think.
inet6_sk_generic() and tcp_inet6_sk() disagree on 32bit kernels by 4-bytes,
because struct tcp_sock has 8-bytes alignment,
but ipv6_pinfo size is not a multiple of 8.
sizeof(struct ipv6_pinfo): 116 (not padded to 8)
I actually first coded tcp_inet6_sk() as this patch does, but thought
that "container_of(tcp_sk(sk), struct tcp6_sock, tcp)" was cleaner.
As Julian told me : Nobody should use tcp6_sock.inet6
directly, it should be accessed via tcp_inet6_sk() or inet6_sk().
This happened when we added the first u64 field in struct tcp_sock.
Fixes: 93a77c11ae79 ("tcp: add tcp_inet6_sk() helper") Signed-off-by: Eric Dumazet <edumazet@google.com> Bisected-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
mlxsw: spectrum_acl: Get rid of failed_rollback mechanism
Jiri says:
Currently if vregion rehash fails, it rolls back to the original ERP
set. However, in case of unlikely rollback fail, the vregion is in a
zombie state and never gets rehashed again. With the recent changes, it
is possible to try to continue the rollback. Do it from the last failed
ventry.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Sun, 31 Mar 2019 06:49:40 +0000 (06:49 +0000)]
mlxsw: spectrum_acl: Remove failed_rollback dead end
Currently if a rollback ends with error, the vregion is in a zombie
state until end of the existence. Instead of that, rather try to
continue where rollback ended later on (after rehash interval).
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vishal Kulkarni [Fri, 29 Mar 2019 12:54:03 +0000 (18:24 +0530)]
cxgb4/cxgb4vf: Display advertised FEC in ethtool
This patch advertises Forward Error Correction in ethtool
Signed-off-by: Casey Leedom <leedom@chelsio.com> Signed-off-by: Vishal Kulkarni <vishal@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
wenxu [Thu, 28 Mar 2019 04:43:23 +0000 (12:43 +0800)]
openvswitch: Make metadata_dst tunnel work in IP_TUNNEL_INFO_BRIDGE mode
There is currently no support for the multicast/broadcast aspects
of VXLAN in ovs. In the datapath flow the tun_dst must specific.
But in the IP_TUNNEL_INFO_BRIDGE mode the tun_dst can not be specific.
And the packet can forward through the fdb table of vxlan devcice. In
this mode the broadcast/multicast packet can be sent through the
following ways in ovs.
ovs-vsctl add-port br0 vxlan -- set in vxlan type=vxlan \
options:key=1000 options:remote_ip=flow
ovs-ofctl add-flow br0 in_port=LOCAL,dl_dst=ff:ff:ff:ff:ff:ff, \
action=output:vxlan
Eric Dumazet [Fri, 29 Mar 2019 19:46:17 +0000 (12:46 -0700)]
tcp: cleanup sk_tx_skb_cache before reuse
TCP stack relies on the fact that a freshly allocated skb
has skb->cb[] and skb_shinfo(skb)->tx_flags cleared.
When recycling tx skb, we must ensure these fields are cleared.
Fixes: 472c2e07eef0 ("tcp: add one skb cache for tx") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Soheil Hassas Yeganeh <soheil@google.com> Cc: Willem de Bruijn <willemb@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmytro Linkin [Thu, 28 Mar 2019 16:09:31 +0000 (16:09 +0000)]
selftests: tc-testing: Add pedit tests
Add 36 pedit action tests to check pedit options described in tc-pedit(8)
man page. Test cases can be specified by categories: actions, pedit,
raw_op, layered_op. RAW_OP cases check offset option for u8, u16 and u32
offset size. LAYERED_OP cases check fields option for eth, ip, ip6,
tcp and udp headers.
Include following tests:
377e - Add pedit action with RAW_OP offset u32
a0ca - Add pedit action with RAW_OP offset u32 (INVALID)
dd8a - Add pedit action with RAW_OP offset u16 u16
53db - Add pedit action with RAW_OP offset u16 (INVALID)
5c7e - Add pedit action with RAW_OP offset u8 add value
2893 - Add pedit action with RAW_OP offset u8 quad
3a07 - Add pedit action with RAW_OP offset u8-u16-u8
ab0f - Add pedit action with RAW_OP offset u16-u8-u8
9d12 - Add pedit action with RAW_OP offset u32 set u16 clear u8 invert
ebfa - Add pedit action with RAW_OP offset overflow u32 (INVALID)
f512 - Add pedit action with RAW_OP offset u16 at offmask shift set
c2cb - Add pedit action with RAW_OP offset u32 retain value
86d4 - Add pedit action with LAYERED_OP eth set src & dst
c715 - Add pedit action with LAYERED_OP eth set src (INVALID)
ba22 - Add pedit action with LAYERED_OP eth type set/clear sequence
5810 - Add pedit action with LAYERED_OP ip set src & dst
1092 - Add pedit action with LAYERED_OP ip set ihl & dsfield
02d8 - Add pedit action with LAYERED_OP ip set ttl & protocol
3e2d - Add pedit action with LAYERED_OP ip set ttl (INVALID)
31ae - Add pedit action with LAYERED_OP ip ttl clear/set
486f - Add pedit action with LAYERED_OP ip set duplicate fields
e790 - Add pedit action with LAYERED_OP ip set ce, df, mf, firstfrag,
nofrag fields
6829 - Add pedit action with LAYERED_OP beyond ip set dport & sport
afd8 - Add pedit action with LAYERED_OP beyond ip set icmp_type &
icmp_code
3143 - Add pedit action with LAYERED_OP beyond ip set dport (INVALID)
fc1f - Add pedit action with LAYERED_OP ip6 set src & dst
6d34 - Add pedit action with LAYERED_OP ip6 dst retain value (INVALID)
6f5e - Add pedit action with LAYERED_OP ip6 flow_lbl
6795 - Add pedit action with LAYERED_OP ip6 set payload_len, nexthdr,
hoplimit
1442 - Add pedit action with LAYERED_OP tcp set dport & sport
b7ac - Add pedit action with LAYERED_OP tcp sport set (INVALID)
cfcc - Add pedit action with LAYERED_OP tcp flags set
3bc4 - Add pedit action with LAYERED_OP tcp set dport, sport & flags
fields
f1c8 - Add pedit action with LAYERED_OP udp set dport & sport
d784 - Add pedit action with mixed RAW/LAYERED_OP #1
70ca - Add pedit action with mixed RAW/LAYERED_OP #2
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Fri, 22 Mar 2019 13:06:09 +0000 (06:06 -0700)]
ipv6: Move ipv6 stubs to a separate header file
The number of stubs is growing and has nothing to do with addrconf.
Move the definition of the stubs to a separate header file and update
users. In the move, drop the vxlan specific comment before ipv6_stub.
Code move only; no functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: Move fib_nh and fib6_nh to a common struct
First set of three with the end goal of enabling IPv6 gateways with IPv4
routes.
This set refactors ipv4 and ipv6 code to create init and release
helpers for each protocol and moving common elements to a fib_nh_common
struct.
v3
- split the reject setting into 2 with helper to the checks. This
avoids changing cfg->fc_flags in fib6_nh_init
v2
- addressed Ido's comments: cleanup on failure path in nh_init helpers,
ordering in fib6_nh_release, and removal of RTF_GATEWAY from fib6_info
uses in mlxsw
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 28 Mar 2019 03:53:58 +0000 (20:53 -0700)]
net: Use common nexthop init and release helpers
With fib_nh_common in place, move common initialization and release
code into helpers used by both ipv4 and ipv6. For the moment, the init
is just the lwt encap and the release is both the netdev reference and
the the lwt state reference. More will be added later.
Signed-off-by: David Ahern <dsahern@gmail.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 28 Mar 2019 03:53:57 +0000 (20:53 -0700)]
net: Add fib_nh_common and update fib_nh and fib6_nh
Add fib_nh_common struct with common nexthop attributes. Convert
fib_nh and fib6_nh to use it. Use macros to move existing
fib_nh_* references to the new nh_common.nhc_*.
Signed-off-by: David Ahern <dsahern@gmail.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 28 Mar 2019 03:53:56 +0000 (20:53 -0700)]
ipv6: Rename fib6_nh entries
Rename fib6_nh entries that will be moved to a fib_nh_common struct.
Specifically, the device, gateway, flags, and lwtstate are common
with all nexthop definitions. In some places new temporary variables
are declared or local variables renamed to maintain line lengths.
Rename only; no functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 28 Mar 2019 03:53:55 +0000 (20:53 -0700)]
ipv4: Rename fib_nh entries
Rename fib_nh entries that will be moved to a fib_nh_common struct.
Specifically, the device, oif, gateway, flags, scope, lwtstate,
nh_weight and nh_upper_bound are common with all nexthop definitions.
In the process shorten fib_nh_lwtstate to fib_nh_lws to avoid really
long lines.
Rename only; no functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 28 Mar 2019 03:53:54 +0000 (20:53 -0700)]
ipv6: Change rt6_add_nexthop and rt6_nexthop_info to take fib6_nh
rt6_add_nexthop and rt6_nexthop_info only need the fib6_info for the
gateway flag and the nexthop weight, and the presence of a gateway is now
per-nexthop. Update the signatures to take a fib6_nh and nexthop weight
and better align with the ipv4 versions.
Signed-off-by: David Ahern <dsahern@gmail.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 28 Mar 2019 03:53:53 +0000 (20:53 -0700)]
ipv6: Refactor fib6_ignore_linkdown
fib6_ignore_linkdown takes a fib6_info but only looks at the net_device
and its IPv6 config. Change it to take a net_device over a fib6_info as
its input argument.
In addition, move it to a header file to make the check inline and usable
later with IPv4 code without going through the ipv6 stub, and rename to
ip6_ignore_linkdown since it is only checking the setting based on the
ipv6 struct on a device.
Signed-off-by: David Ahern <dsahern@gmail.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 28 Mar 2019 03:53:52 +0000 (20:53 -0700)]
ipv6: Move gateway checks to a fib6_nh setting
The gateway setting is not per fib6_info entry but per-fib6_nh. Add a new
fib_nh_has_gw flag to fib6_nh and convert references to RTF_GATEWAY to
the new flag. For IPv6 address the flag is cheaper than checking that
nh_gw is non-0 like IPv4 does.
While this increases fib6_nh by 8-bytes, the effective allocation size of
a fib6_info is unchanged. The 8 bytes is recovered later with a
fib_nh_common change.
Signed-off-by: David Ahern <dsahern@gmail.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 28 Mar 2019 03:53:50 +0000 (20:53 -0700)]
ipv6: Create init helper for fib6_nh
Similar to IPv4, consolidate the fib6_nh initialization into a helper.
As a new standalone function, add a cleanup path to put lwtstate on
error.
To avoid modifying fib6_config flags, move the reject check to a helper
that is invoked once by fib6_nh_init to reset the device and then
again in ip6_route_info_create to set the fib6_flags.
Signed-off-by: David Ahern <dsahern@gmail.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 28 Mar 2019 03:53:49 +0000 (20:53 -0700)]
ipv4: Create cleanup helper for fib_nh
Move the fib_nh cleanup code from free_fib_info_rcu into a new helper,
fib_nh_release. Move classid accounting into fib_nh_release which is
called per fib_nh to make accounting symmetrical with fib_nh_init.
Export the helper to allow for use with nexthop objects in the
future.
Signed-off-by: David Ahern <dsahern@gmail.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 28 Mar 2019 03:53:48 +0000 (20:53 -0700)]
ipv4: Create init helper for fib_nh
Consolidate the fib_nh initialization which is duplicated between
fib_create_info for single path and fib_get_nhs for multipath.
Export the helper to allow for use with nexthop objects in the
future.
Signed-off-by: David Ahern <dsahern@gmail.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 28 Mar 2019 03:53:47 +0000 (20:53 -0700)]
ipv4: Move IN_DEV_IGNORE_ROUTES_WITH_LINKDOWN to helper
in_dev lookup followed by IN_DEV_IGNORE_ROUTES_WITH_LINKDOWN check
is called in several places, some with the rcu lock and others with the
rtnl held.
Move the check to a helper similar to what IPv6 has. Since the helper
can be invoked from either context use rcu_dereference_rtnl to
dereference ip_ptr.
Signed-off-by: David Ahern <dsahern@gmail.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 28 Mar 2019 03:53:46 +0000 (20:53 -0700)]
ipv4: Define fib_get_nhs when CONFIG_IP_ROUTE_MULTIPATH is disabled
Define fib_get_nhs to return EINVAL when CONFIG_IP_ROUTE_MULTIPATH is
not enabled and remove the ifdef check for CONFIG_IP_ROUTE_MULTIPATH
in fib_create_info.
Signed-off-by: David Ahern <dsahern@gmail.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 28 Mar 2019 12:12:27 +0000 (12:12 +0000)]
selftests: mlxsw: Add a new test for strict priority
Test that when strict priority is configured on a system, the
higher-priority traffic does actually win all the available bandwidth.
The test uses a similar approach to qos_mc_aware.sh to run and account
the traffic.
Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 28 Mar 2019 12:12:26 +0000 (12:12 +0000)]
selftests: mlxsw: Add qos_lib.sh
Extract reusable code from qos_mc_aware.sh and put into a new library.
Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This test runs two streams of traffic from two independent ports to
create congestion on one egress port. It is necessary to configure the
shared buffer thresholds correctly, to make sure that there is traffic
from both streams in the shared buffer. Only then can the test actually
test prioritization among these streams.
Without this configuration, it is possible, that one of the streams
takes all of port-pool quota, and the other stream is not even admitted,
thus invalidating the result.
On Spectrum-1, this is not a problem, because MC traffic uses a separate
pool. But for Spectrum-2, MC and UC share the same pool, and the correct
configuration is important.
Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to obtain, set, and restore a pool size, and a port-pool and
tc-pool threshold.
Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 28 Mar 2019 12:12:23 +0000 (12:12 +0000)]
selftests: forwarding: devlink_lib: Simplify deduction of DEVLINK_DEV
Use devlink -j and jq for more accurate querying. Use cut -f-2 instead
of rev-cut-rev combo.
Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 28 Mar 2019 12:12:23 +0000 (12:12 +0000)]
selftests: forwarding: devlink_lib: Avoid double sourcing of lib.sh
Don't source lib.sh twice and make the script work with ifnames passed
on the command line.
Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Danielle Ratson [Thu, 28 Mar 2019 12:12:21 +0000 (12:12 +0000)]
selftests: forwarding: Test action VLAN modify
Construct a basic topology consisting of two hosts connected using a
VLAN-aware bridge. Put each port in a different VLAN and test that ping
fails.
Add ingress and egress filters with a VLAN modify action and test that
ping passes.
Signed-off-by: Danielle Ratson <danieller@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 28 Mar 2019 12:12:19 +0000 (12:12 +0000)]
selftests: forwarding: Add reverse path forwarding (RPF) test cases
In case a packet is routed using a multicast route whose specified
ingress interface does not match the interface from which the packet was
received, the packet is dropped.
Add IPv4 and IPv6 test cases for above mentioned scenario.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHYs will use the 2500BaseX PHY_INTERFACE_MODE when being linked
with a partner using 2.5GBaseT.
Since we can't autonegotiate this speed between the MAC and the PHY, we
need to have the proper comphy support enabled, to make sure we can
safely advertise 2.5G and 1G in BaseT and be able to switch between both
corresponding PHY interface modes. This is now possible since comphy
support was added to this driver.
This commit adds the 2500BaseT mode to the list of supported modes when
using 2500BaseX, and was tested on a setup with an Armada385 and a 88E2010 PHY, both with and without the comphy node in the DT.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yi-Hung Wei [Tue, 26 Mar 2019 18:31:14 +0000 (11:31 -0700)]
openvswitch: Add timeout support to ct action
Add support for fine-grain timeout support to conntrack action.
The new OVS_CT_ATTR_TIMEOUT attribute of the conntrack action
specifies a timeout to be associated with this connection.
If no timeout is specified, it acts as is, that is the default
timeout for the connection will be automatically applied.
Example usage:
$ nfct timeout add timeout_1 inet tcp syn_sent 100 established 200
$ ovs-ofctl add-flow br0 in_port=1,ip,tcp,action=ct(commit,timeout=timeout_1)
CC: Pravin Shelar <pshelar@ovn.org> CC: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Yi-Hung Wei <yihung.wei@gmail.com> Acked-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Yi-Hung Wei [Tue, 26 Mar 2019 18:31:13 +0000 (11:31 -0700)]
netfilter: Export nf_ct_{set,destroy}_timeout()
This patch exports nf_ct_set_timeout() and nf_ct_destroy_timeout().
The two functions are derived from xt_ct_destroy_timeout() and
xt_ct_set_timeout() in xt_CT.c, and moved to nf_conntrack_timeout.c
without any functional change.
It would be useful for other users (i.e. OVS) that utilizes the
finer-grain conntrack timeout feature.
CC: Pablo Neira Ayuso <pablo@netfilter.org> CC: Pravin Shelar <pshelar@ovn.org> Signed-off-by: Yi-Hung Wei <yihung.wei@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
please apply the following patchset to net-next. This reworks the control
IO code in qeth so that we no longer need to poll for cmd completion,
and refactors the IDX setup code to also use this improved IO path.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 28 Mar 2019 15:39:28 +0000 (16:39 +0100)]
s390/qeth: send IDX cmds via qeth_send_control_data()
This converts the IDX code to use qeth_send_control_data(), replacing
a bunch of duplicated IO code and unbounded waits. It also allows the
IDX sequence to benefit from the improved timeout & notify
infrastructure, so that we can eliminate the DOWN -> ACTIVATING -> UP
transition in the channel state machine.
The patch looks rather big, but most of it is a straight-forward
conversion of the old IDX cmd setup & callbacks to the new model.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 28 Mar 2019 15:39:27 +0000 (16:39 +0100)]
s390/qeth: use callback to finalize cmd
To avoid concurrency issues, some parts of the cmd setup are delayed
until qeth_send_control_data() holds the IO channel's irq_pending
"lock". Rather than hard-coding those setup steps for each cmd type,
have the cmd provide a callback. This will make it easier to also issue
IDX commands via qeth_send_control_data().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 28 Mar 2019 15:39:25 +0000 (16:39 +0100)]
s390/qeth: clarify default cmd callback
Current code makes it look like qeth_send_control_data_cb() is some
sort of default callback for all cmds. But in practice, it is only used
for half of the cmd buffers we issue.
Reduce the confusion by only setting this callback for cmds that
actually want it, and while at it give the callback a name that matches
the established naming scheme.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 28 Mar 2019 15:39:22 +0000 (16:39 +0100)]
s390/qeth: defer IPv6 address notifier events
The inet6addr_chain is atomic. So instead of starting the cmd IO for
SETIP / DELIP straight from the notifier callback, run it from a
workqueue. This is the last step towards removal of cmd IO completion
polling.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 28 Mar 2019 15:39:21 +0000 (16:39 +0100)]
s390/qeth: add wrapper for IP table access
Extract a little helper, so that high-level callers can manipulate the
IP table without worrying about the locking. This will make it easier
to convert the code to a different locking primitive later on.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 28 Mar 2019 15:39:20 +0000 (16:39 +0100)]
s390/qeth: remove locking for RX modeset cache
The L2 and L3 .ndo_set_rx_mode callbacks maintain an address cache
to decide which addresses have changed since the last modeset.
When the card is set offline, qeth_l?_stop_card() drains this cache.
This happens only after 1) the net_device has been detached, and
2) any pending RX modeset has completed. Consequently we can access the
cache lock-free.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 28 Mar 2019 15:39:19 +0000 (16:39 +0100)]
s390/qeth: defer RX modesetting
.ndo_set_rx_mode gets called in process context, but while holding the
addr_list spinlock. Which means we currently can't sleep while
re-programming the HW, and need to poll for IO completion. That's bad,
in particular since receiving the cmd response can fail silently and
we're then polling until the timeout hits.
As a first step towards eliminating the IO completion polling, run the
RX modeset from a work element and only take the addr_list lock while
updating the RX mode address cache.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
===================
net: call for phys_port_name into devlink directly if possible
phys_port_name may be assembled by a helper in devlink. It is currently
the case only for mlxsw driver. Benefit from the get_devlink_port ndo
and call into devlink directly from dev_get_phys_port_name(). That saves
the trip to the driver, simplifies the code and makes it similar to
recently introduced ethtool-devlink compat helpers.
Move bnxt, partly nfp and dsa to let devlink core generate the name too.
===================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 28 Mar 2019 12:56:46 +0000 (13:56 +0100)]
net: devlink: add warning for ndo_get_phys_port_name set when not needed
Currently if the driver registers devlink port instance, it should set
the devlink port attributes as well. Then the devlink core is able to
obtain physical port name itself, no need for driver to implement
the ndo. Once all drivers will implement devlink port registration,
this ndo should be removed. This warning guides new
drivers to do things as they should be done.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 28 Mar 2019 12:56:45 +0000 (13:56 +0100)]
nfp: do not handle nn->port defined case in nfp_net_get_phys_port_name()
If nn->port is defined it means that devlink_port has been registered
for this port as well. Devlink core is handling the port name
formatting.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 28 Mar 2019 12:56:44 +0000 (13:56 +0100)]
dsa: do not support ndo_get_phys_port_name for non-legacy ports
Since each non-legacy slave has its own devlink port instance
correctly set, rely on devlink core to generate correct phys port name.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 28 Mar 2019 12:56:43 +0000 (13:56 +0100)]
dsa: implement ndo_get_devlink_port
In order for devlink compat functions to work, implement
ndo_get_devlink_port. Legacy slaves does not have devlink port instances
created for themselves.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 28 Mar 2019 12:56:41 +0000 (13:56 +0100)]
bnxt: implement ndo_get_devlink_port
In order for devlink compat functions to work, implement
ndo_get_devlink_port. Legacy slaves does not have devlink port instances
created for themselves.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-jammy-kernel.git / log