The subpage_prot syscall is only functional when the system is using
the Hash MMU. Since commit 5b2b80714796 ("powerpc/mm: Invalidate
subpage_prot() system call on radix platforms") it returns ENOENT when
the Radix MMU is active. Currently this just makes the test fail.
Additionally the syscall is not available if the kernel is built with
4K pages, or if CONFIG_PPC_SUBPAGE_PROT=n, in which case it returns
ENOSYS because the syscall is missing entirely.
So check explicitly for ENOENT and ENOSYS and skip if we see either of
those.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
bio_devname use __bdevname to display the device name, and can
only show the major and minor of the part0,
Fix this by using disk_name to display the correct name.
Fixes: 74d46992e0d9 ("block: replace bi_bdev with a gendisk pointer and partitions index") Reviewed-by: Omar Sandoval <osandov@fb.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jiufei Xue <jiufei.xue@linux.alibaba.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If in the same transaction we rename a special file (fifo, character/block
device or symbolic link), create a hard link for it having its old name
then sync the log, we will end up with a log that can not be replayed and
at when attempting to replay it, an EEXIST error is returned and mounting
the filesystem fails. Example scenario:
$ mkfs.btrfs -f /dev/sdc
$ mount /dev/sdc /mnt
$ mkdir /mnt/testdir
$ mkfifo /mnt/testdir/foo
# Make sure everything done so far is durably persisted.
$ sync
# Create some unrelated file and fsync it, this is just to create a log
# tree. The file must be in the same directory as our special file.
$ touch /mnt/testdir/f1
$ xfs_io -c "fsync" /mnt/testdir/f1
# Rename our special file and then create a hard link with its old name.
$ mv /mnt/testdir/foo /mnt/testdir/bar
$ ln /mnt/testdir/bar /mnt/testdir/foo
# Create some other unrelated file and fsync it, this is just to persist
# the log tree which was modified by the previous rename and link
# operations. Alternatively we could have modified file f1 and fsync it.
$ touch /mnt/f2
$ xfs_io -c "fsync" /mnt/f2
<power failure>
$ mount /dev/sdc /mnt
mount: mount /dev/sdc on /mnt failed: File exists
This happens because when both the log tree and the subvolume's tree have
an entry in the directory "testdir" with the same name, that is, there
is one key (258 INODE_REF 257) in the subvolume tree and another one in
the log tree (where 258 is the inode number of our special file and 257
is the inode for directory "testdir"). Only the data of those two keys
differs, in the subvolume tree the index field for inode reference has
a value of 3 while the log tree it has a value of 5. Because the same key
exists in both trees, but have different index, the log replay fails with
an -EEXIST error when attempting to replay the inode reference from the
log tree.
Fix this by setting the last_unlink_trans field of the inode (our special
file) to the current transaction id when a hard link is created, as this
forces logging the parent directory inode, solving the conflict at log
replay time.
A new generic test case for fstests was also submitted.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When doing an incremental send of a filesystem with the no-holes feature
enabled, we end up issuing a write operation when using the no data mode
send flag, instead of issuing an update extent operation. Fix this by
issuing the update extent operation instead.
Trivial reproducer:
$ mkfs.btrfs -f -O no-holes /dev/sdc
$ mkfs.btrfs -f /dev/sdd
$ mount /dev/sdc /mnt/sdc
$ mount /dev/sdd /mnt/sdd
The srcu_struct in btrfs_fs_info scales in size with NR_CPUS. On
kernels built with NR_CPUS=8192, this can result in kmalloc failures
that prevent mounting.
There is work in progress to try to resolve this for every user of
srcu_struct but using kvzalloc will work around the failures until
that is complete.
As an example with NR_CPUS=512 on x86_64: the overall size of
subvol_srcu is 3460 bytes, fs_info is 6496.
Signed-off-by: Jeff Mahoney <jeffm@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Back in the early days when gru devices were still under development
we found an issue where the WiFi reset line needed to be configured as
early as possible during the boot process to avoid the WiFi module
being in a bad state.
We found that the way to get the kernel to do this in the earliest
possible place was to configure this line in the pinctrl hogs, so
that's what we did. For some history here you can see
<http://crosreview.com/368770>. After the time that change landed in
the kernel, we landed a firmware change to configure this line even
earlier. See <http://crosreview.com/399919>. However, even after the
firmware change landed we kept the kernel change to deal with the fact
that some people working on devices might take a little while to
update their firmware.
At this there are definitely zero devices out in the wild that have
firmware without the fix in it. Specifically looking in the firmware
branch several critically important fixes for memory stability landed
after the patch in coreboot and I know we didn't ship without those.
Thus, by now, everyone should have the new firmware and it's safe to
not have the kernel set this up in a pinctrl hog.
Historically, even though it wasn't needed to have this in a pinctrl
hog, we still kept it since it didn't hurt. Pinctrl would apply the
default hog at bootup and then would never touch things again. That
all changed with commit 981ed1bfbc6c ("pinctrl: Really force states
during suspend/resume"). After that commit then we'll re-apply the
default hog at resume time and that can screw up the reset state of
WiFi. ...and on rk3399 if you touch a device on PCIe in the wrong way
then the whole system can go haywire. That's what was happening.
Specifically you'd resume a rk3399-gru-* device and it would mostly
resume, then would crash with some crazy weird crash.
One could say, perhaps, that the recent pinctrl change was at fault
(and should be fixed) since it changed behavior. ...but that's not
really true. The device tree for rk3399-gru is really to blame.
Specifically since the pinctrl is defined in the hog and not in the
"wlan-pd-n" node then the actual user of this pin doesn't have a
pinctrl entry for it. That's bad.
Let's fix our problems by just moving the control of
"wlan_module_reset_l pinctrl" out of the hog and put them in the
proper place.
NOTE: in theory, I think it should actually be possible to have a pin
controlled _both_ by the hog and by an actual device. Once the device
claims the pin I think the hog is supposed to let go. I'm not 100%
sure that this works and in any case this solution would be more
complex than is necessary.
Reported-by: Marc Zyngier <marc.zyngier@arm.com> Fixes: 48f4d9796d99 ("arm64: dts: rockchip: add Gru/Kevin DTS") Fixes: 981ed1bfbc6c ("pinctrl: Really force states during suspend/resume") Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Tested-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When IPsec offloading was introduced, we accidentally incremented
the sequence number counter on the xfrm_state by one packet
too much in the ESN case. This leads to a sequence number gap of
one packet after each GSO packet. Fix this by setting the sequence
number to the correct value.
Current cleanup in the error path of xen_bind_pirq_msi_to_irq is
wrong. First of all there's an off-by-one in the cleanup loop, which
can lead to unbinding wrong IRQs.
Secondly IRQs not bound won't be freed, thus leaking IRQ numbers.
Note that there's no need to differentiate between bound and unbound
IRQs when freeing them, __unbind_from_irq will deal with both of them
correctly.
Fixes: 4892c9b4ada9f9 ("xen: add support for MSI message groups") Reported-by: Hooman Mirhadi <mirhadih@amazon.com> Signed-off-by: Roger Pau Monné <roger.pau@citrix.com> Reviewed-by: Amit Shah <aams@amazon.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
To support host systems with non 4K page size, l2_db_size shall be
calculated with 4096 instead of PAGE_SIZE. Also, supply the host page size
to FW during initialization.
IB spec says that a lid should be ignored when link layer is Ethernet,
for example when building or parsing a CM request message (CA17-34).
However, since ib_lid_be16() and ib_lid_cpu16() validates the slid,
not only when link layer is IB, we set the slid to zero to prevent
false warnings in the kernel log.
Fixes: 62ede7779904 ("Add OPA extended LID support") Reviewed-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Moni Shoua <monis@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The IPS_NAT_MASK check in 4.12 replaced previous check for nfct_nat()
which was needed to fix a crash in 2.6.36-rc, see
commit 7bcbf81a2296 ("ipvs: avoid oops for passive FTP").
But as IPVS does not set the IPS_SRC_NAT and IPS_DST_NAT bits,
checking for IPS_NAT_MASK prevents PASV response to be properly
mangled and blocks the transfer. Remove the check as it is not
needed after 3.12 commit 41d73ec053d2 ("netfilter: nf_conntrack:
make sequence number adjustments usuable without NAT") which
changes nfct_nat() with nfct_seqadj() and especially after 3.13
commit b25adce16064 ("ipvs: correct usage/allocation of seqadj
ext in ipvs").
Thanks to Li Shuang and Florian Westphal for reporting the problem!
As we have option in u-boot to set CPU mask for running linux,
we want to pass information to kernel about CPU cores should
be brought up. So we patch kernel dtb in u-boot to set
possible-cpus property.
This also allows us to have correctly setuped MCIP debug mask.
As of today we use hardcoded MCIP debug mask, so if we launch
kernel via debugger and kick fever cores than HW has all cpus
hang at the momemt of setup MCIP debug mask.
So update MCIP debug mask when the new cpu came online, instead of
use hardcoded MCIP debug mask.
In SMP systems, GFRC is used for clocksource. However by default the
counter keeps running even when core is halted (say when debugging via a
JTAG debugger). This confuses Linux timekeeping and triggers flase RCU stall
splat such as below:
| [ARCLinux]# while true; do ./shm_open_23-1.run-test ; done
| Running with 1000 processes for 1000 objects
| hrtimer: interrupt took 485060 ns
|
| create_cnt: 1000
| Running with 1000 processes for 1000 objects
| [ARCLinux]# INFO: rcu_preempt self-detected stall on CPU
| 2-...: (1 GPs behind) idle=a01/1/0 softirq=135770/135773 fqs=0
| INFO: rcu_preempt detected stalls on CPUs/tasks:
| 0-...: (1 GPs behind) idle=71e/0/0 softirq=135264/135264 fqs=0
| 2-...: (1 GPs behind) idle=a01/1/0 softirq=135770/135773 fqs=0
| 3-...: (1 GPs behind) idle=4e0/0/0 softirq=134304/134304 fqs=0
| (detected by 1, t=13648 jiffies, g=31493, c=31492, q=1)
Starting from ARC HS v3.0 it's possible to tie GFRC to state of up-to 4
ARC cores with help of GFRC's CORE register where we set a mask for
cores which state we need to rely on.
We update cpu mask every time new cpu came online instead of using
hardcoded one or using mask generated from "possible_cpus" as we
want it set correctly even if we run kernel on HW which has fewer cores
than expected (or we launch kernel via debugger and kick fever cores
than HW has)
Note that GFRC halts when all cores have halted and thus relies on
programming of Inter-Core-dEbug register to halt all cores when one
halts.
One of the basic construct in the device is a port-VLAN pair, which can
be bound to a FID or a RIF in order to direct packets to the bridge or
the router, respectively.
Since not all the netdevs are configured with a VLAN (e.g., sw1p1 vs.
sw1p1.10), VID 1 is used to represent these and thus this VID can be
used by both upper devices of mlxsw ports and by the driver itself.
However, this VID is not reference counted and therefore might be freed
prematurely, which can result in various WARNINGs. For example:
$ ip link add name br0 type bridge vlan_filtering 1
$ teamd -t team0 -d -c '{"runner": {"name": "lacp"}}'
$ ip link set dev team0 master br0
$ ip link set dev enp1s0np1 master team0
$ ip address add 192.0.2.1/24 dev enp1s0np1
The enslavement to team0 will fail because team0 already has an upper
and thus vlan_vids_del_by_dev() will be executed as part of team's error
path which will delete VID 1 from enp1s0np1 (added by br0 as PVID). The
WARNING will be generated when the driver will realize it can't find VID
1 on the port and bind it to a RIF.
Fix this by adding a reference count to the VLAN entries on the port, in
a similar fashion to the reference counting used by the corresponding
'vlan_vid_info' structure in the 8021q driver.
Fixes: c57529e1d5d8 ("mlxsw: spectrum: Replace vPorts with Port-VLAN") Reported-by: Tal Bar <talb@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Tested-by: Tal Bar <talb@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When multicast snooping is enabled, the Linux bridge resorts to flooding
unregistered multicast packets to all ports only in case it did not
detect a querier in the network.
The above condition is not reflected to underlying drivers, which is
especially problematic in IPv6 environments, as multicast snooping is
enabled by default and since neighbour solicitation packets might be
treated as unregistered multicast packets in case there is no
corresponding MDB entry.
Until the Linux bridge reflects its querier state to underlying drivers,
simply treat unregistered multicast packets as broadcast and allow them
to reach their destination.
Fixes: 9df552ef3e21 ("mlxsw: spectrum: Improve IPv6 unregistered multicast flooding") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: David Ahern <dsahern@gmail.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
PSDT field section according to NVM_Express-1.3:
"This field specifies whether PRPs or SGLs are used for any data
transfer associated with the command. PRPs shall be used for all
Admin commands for NVMe over PCIe. SGLs shall be used for all Admin
and I/O commands for NVMe over Fabrics. This field shall be set to
01b for NVMe over Fabrics 1.0 implementations.
Suggested-by: Idan Burstein <idanb@mellanox.com> Signed-off-by: Max Gurtovoy <maxg@mellanox.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The link to the pdf containing the algorithm description is now a
dead link; it seems http://www.ifp.illinois.edu/~srikant/ has been
moved to https://sites.google.com/a/illinois.edu/srikant/ and none of
the original papers can be found there...
I have replaced it with the only working copy I was able to find.
However, this seems to only be a *cached* version, so I am unsure
exactly how reliable that link can be expected to remain over time
and have decided against using that one.
Don't include in the Rx bytecount of the packet sent up the stack:
the FCB (frame control block), and the padding bytes inserted by
the controller into the frame payload, nor the FCS. All these are
being pulled out of the skb by gfar_process_frame().
This issue is old, likely from the driver's beginnings, however
it was amplified by recent:
commit d903ec77118c ("gianfar: simplify FCS handling and fix memory leak")
which basically added the FCS to the Rx bytecount, and so brought
this to my attention.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
__gic_clocksource_init() extracts the GIC_CONFIG_COUNTBITS field from
read_gic_config() by right shifting the register value. The shift count is
determined by the most significant bit (__fls) of the bitmask which is
wrong as it shifts out the complete bitfield.
Use the least significant bit (__ffs) instead to shift the bitfield down to
bit 0.
Fixes: e07127a077c7 ("clocksource: mips-gic-timer: Use new GIC accessor functions") Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: daniel.lezcano@linaro.org Cc: paul.burton@imgtec.com Link: https://lkml.kernel.org/r/20180228095610.50341-1-nbd@nbd.name Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Once in a while I see build errors similar to the following
when building images from a clean tree.
Building powerpc:virtex-ml507:44x/virtex5_defconfig ... failed
------------
Error log:
arch/powerpc/boot/treeboot-akebono.c:37:20: fatal error:
libfdt.h: No such file or directory
Building powerpc:bamboo:smpdev:44x/bamboo_defconfig ... failed
------------
Error log:
arch/powerpc/boot/treeboot-akebono.c:37:20: fatal error:
libfdt.h: No such file or directory
arch/powerpc/boot/treeboot-currituck.c:35:20: fatal error:
libfdt.h: No such file or directory
Rebuilds will succeed.
Turns out that several source files in arch/powerpc/boot/ include
libfdt.h, but Makefile dependencies are incomplete. Let's fix that.
Jon attempted to fix the amount of RAM on the BCM958625HR in commit c53beb47f621 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
but it seems like we tripped over some poorly documented schematics.
The top-level page of the schematics says the board has 2GB, but when
you end-up scrolling to page 6, you see two chips of 4GBit (512MB) but
what the bootloader really initializes only 512MB, any attempt to use
more than that results in data aborts. Fix this again back to 512MB.
Commit 128bb975dc3c ("ip6_gre: init dev->mtu and dev->hard_header_len
correctly") fixed IFLA_MTU ignored on NEWLINK for ip6_gre. The same
mtu fix is also needed for sit.
Note that dev->hard_header_len setting for sit works fine, no need to
fix it. sit is actually ipv4 tunnel, it can't call ip6_tnl_change_mtu
to set mtu.
Reported-by: Jianlin Shi <jishi@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 128bb975dc3c ("ip6_gre: init dev->mtu and dev->hard_header_len
correctly") fixed IFLA_MTU ignored on NEWLINK for ip6_gre. The same
mtu fix is also needed for ip6_tunnel.
Note that dev->hard_header_len setting for ip6_tunnel works fine,
no need to fix it.
Reported-by: Jianlin Shi <jishi@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
All the crash issue happened when a bypass IO coming, in such scenario
s->iop.bio is pointed to the s->orig_bio. In search_free(), it finishes the
s->orig_bio by calling bio_complete(), and after that, s->iop.bio became
invalid, then kernel would crash when calling bio_put(). Maybe its upper
layer's faulty, since bio should not be freed before we calling bio_put(),
but we'd better calling bio_put() first before calling bio_complete() to
notify upper layer ending this bio.
This patch moves bio_complete() under bio_put() to avoid kernel crash.
[mlyle: fixed commit subject for character limits]
Reported-by: Matthias Ferdinand <bcache@mfedv.net> Tested-by: Matthias Ferdinand <bcache@mfedv.net> Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn> Reviewed-by: Michael Lyle <mlyle@lyle.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
According to R-Car Gen3 Rev.0.80 manual, the DMATCR can be set to
16,777,215 as maximum. So, this patch fixes the max_chunk_size for
safety on all of SoCs. Otherwise, a system may hang if the DMATCR
is set to 0 on R-Car Gen3.
r8152 driver handles TSO packets (limited to ~16KB) quite well,
but pretends each TSO logical packet is a single packet on the wire.
There is also some error since headers are accounted once, but
error rate is small enough that we do not care.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The Makefile lacks a couple of line continuation backslashes
in an `if' clause, which produces an error when make versions
prior to 4.x are used for building the tests.
$ make
make[1]: Entering directory `/[...]/linux/tools/testing/selftests/futex'
/bin/sh: -c: line 5: syntax error: unexpected end of file
make[1]: *** [all] Error 1
make[1]: Leaving directory `/[...]/linux/tools/testing/selftests/futex'
make: *** [all] Error 2
Added MODULE_ALIAS("rpmsg:IPCRTR") to ensure qrtr-smd and qrtr will load
when IPCRTR channel is detected.
Signed-off-by: Ramon Fried <rfried@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
First of all, the orion5x buffer is not NULL terminated. mac_pton()
has no business operating on non-NULL terminated buffers because
only the caller can know that this is valid and in what manner it
is ok to parse this NULL'less buffer.
Second of all, orion5x operates on an __iomem pointer, which cannot
be dereferenced using normal C pointer operations. Accesses to
such areas much be performed with the proper iomem accessors.
Fixes: 4904dbda41c8 ("ARM: orion5x: use mac_pton() helper") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently if map is null then a potential null pointer deference
occurs when calling sock_release on map->sock. I believe the
actual intention was to call sock_release on sock instead. Fix
this.
Fixes: 5db4d286a8ef ("xen/pvcalls: implement connect command") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When failing from ceph_fs_debugfs_init() in ceph_real_mount(),
there is lack of dput of root_dentry and it causes slab errors,
so change the calling order of ceph_fs_debugfs_init() and
open_root_dentry() and do some cleanups to avoid this issue.
The error checks on freq for a negative error return always fails because
freq is unsigned and can never be negative. Fix this by making freq a
signed long.
Detected with Coccinelle:
drivers/clocksource/fsl_ftm_timer.c:287:5-9: WARNING: Unsigned expression
compared with zero: freq <= 0
drivers/clocksource/fsl_ftm_timer.c:291:5-9: WARNING: Unsigned expression
compared with zero: freq <= 0
Fixes: 2529c3a33079 ("clocksource: Add Freescale FlexTimer Module (FTM) timer support") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: kernel-janitors@vger.kernel.org Link: https://lkml.kernel.org/r/20180226113614.3092-1-colin.king@canonical.com Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This patch fixes nvme queue cleanup if requesting an IRQ handler for
the queue's vector fails. It does this by resetting the cq_vector to
the uninitialized value of -1 so it is ignored for a controller reset.
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
[changelog updates, removed misc whitespace changes] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The function batadv_bla_backbone_dump_bucket must be able to handle
non-complete dumps of a single bucket. It tries to do that by saving the
latest dumped index in *idx_skip to inform the caller about the current
state.
But the caller only assumes that buckets were not completely dumped when
the return code is non-zero. This function must therefore also return a
non-zero index when the dumping of an entry failed. Otherwise the caller
will just skip all remaining buckets.
And the function must also reset *idx_skip back to zero when it finished a
bucket. Otherwise it will skip the same number of entries in the next
bucket as the previous one had.
The function batadv_bla_claim_dump_bucket must be able to handle
non-complete dumps of a single bucket. It tries to do that by saving the
latest dumped index in *idx_skip to inform the caller about the current
state.
But the caller only assumes that buckets were not completely dumped when
the return code is non-zero. This function must therefore also return a
non-zero index when the dumping of an entry failed. Otherwise the caller
will just skip all remaining buckets.
And the function must also reset *idx_skip back to zero when it finished a
bucket. Otherwise it will skip the same number of entries in the next
bucket as the previous one had.
Fixes: 04f3f5bf1883 ("batman-adv: add B.A.T.M.A.N. Dump BLA claims via netlink") Reported-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The function batadv_v_gw_dump stops the processing loop when
batadv_v_gw_dump_entry returns a non-0 return code. This should only
happen when the buffer is full. Otherwise, an empty message may be
returned by batadv_gw_dump. This empty message will then stop the netlink
dumping of gateway entries. At worst, not a single entry is returned to
userspace even when plenty of possible gateways exist.
Fixes: b71bb6f924fe ("batman-adv: add B.A.T.M.A.N. V bat_gw_dump implementations") Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The function batadv_iv_gw_dump stops the processing loop when
batadv_iv_gw_dump_entry returns a non-0 return code. This should only
happen when the buffer is full. Otherwise, an empty message may be
returned by batadv_gw_dump. This empty message will then stop the netlink
dumping of gateway entries. At worst, not a single entry is returned to
userspace even when plenty of possible gateways exist.
Fixes: efb766af06e3 ("batman-adv: add B.A.T.M.A.N. IV bat_gw_dump implementations") Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Once struct is added to per-netns list it becomes visible to other cpus,
so we cannot use kfree().
Also delay setting entries refcount to 1 until after everything is
initialised so that when we call clusterip_config_put() in this spot
entries is still zero.
A more sophisticated implementation could try to combine fragment checksums
when all fragments have CHECKSUM_COMPLETE and are split at even offsets.
For now, we just set ip_summed to CHECKSUM_NONE to avoid "hw csum failure"
warnings in the kernel log when fragmented frames are received. In
consequence, skb_pull_rcsum() can be replaced with skb_pull().
Note that in usual setups, packets don't reach batman-adv with
CHECKSUM_COMPLETE (I assume NICs bail out of checksumming when they see
batadv's ethtype?), which is why the log messages do not occur on every
system using batman-adv. I could reproduce this issue by stacking
batman-adv on top of a VXLAN interface.
Fixes: 610bfc6bc99b ("batman-adv: Receive fragmented packets and merge") Tested-by: Maximilian Wilhelm <max@sdn.clinic> Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
eth_type_trans() internally calls skb_pull(), which does not adjust the
skb checksum; skb_postpull_rcsum() is necessary to avoid log spam of the
form "bat0: hw csum failure" when packets with CHECKSUM_COMPLETE are
received.
Note that in usual setups, packets don't reach batman-adv with
CHECKSUM_COMPLETE (I assume NICs bail out of checksumming when they see
batadv's ethtype?), which is why the log messages do not occur on every
system using batman-adv. I could reproduce this issue by stacking
batman-adv on top of a VXLAN interface.
Fixes: c6c8fea29769 ("net: Add batman-adv meshing protocol") Tested-by: Maximilian Wilhelm <max@sdn.clinic> Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In handle_write_finished(), if r1_bio->bios[m] != NULL, it thinks
the corresponding conf->mirrors[m].rdev is also not NULL. But, it
is not always true.
Even if some io hold replacement rdev(i.e. rdev->nr_pending.count > 0),
raid1_remove_disk() can also set the rdev as NULL. That means,
bios[m] != NULL, but mirrors[m].rdev is NULL, resulting in NULL
pointer dereference in handle_write_finished and sync_request_write.
There is a potential deadlock if mount/umount happens when
raid5_finish_reshape() tries to grow the size of emulated disk.
How the deadlock happens?
1) The raid5 resync thread finished reshape (expanding array).
2) The mount or umount thread holds VFS sb->s_umount lock and tries to
write through critical data into raid5 emulated block device. So it
waits for raid5 kernel thread handling stripes in order to finish it
I/Os.
3) In the routine of raid5 kernel thread, md_check_recovery() will be
called first in order to reap the raid5 resync thread. That is,
raid5_finish_reshape() will be called. In this function, it will try
to update conf and call VFS revalidate_disk() to grow the raid5
emulated block device. It will try to acquire VFS sb->s_umount lock.
The raid5 kernel thread cannot continue, so no one can handle mount/
umount I/Os (stripes). Once the write-through I/Os cannot be finished,
mount/umount will not release sb->s_umount lock. The deadlock happens.
The raid5 kernel thread is an emulated block device. It is responible to
handle I/Os (stripes) from upper layers. The emulated block device
should not request any I/Os on itself. That is, it should not call VFS
layer functions. (If it did, it will try to acquire VFS locks to
guarantee the I/Os sequence.) So we have the resync thread to send
resync I/O requests and to wait for the results.
For solving this potential deadlock, we can put the size growth of the
emulated block device as the final step of reshape thread.
2017/12/29:
Thanks to Guoqing Jiang <gqjiang@suse.com>,
we confirmed that there is the same deadlock issue in raid10. It's
reproducible and can be fixed by this patch. For raid10.c, we can remove
the similar code to prevent deadlock as well since they has been called
before.
Reported-by: Alex Wu <alexwu@synology.com> Reviewed-by: Alex Wu <alexwu@synology.com> Reviewed-by: Chung-Chiang Cheng <cccheng@synology.com> Signed-off-by: BingJing Chang <bingjingc@synology.com> Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
i_dir_seq is subject to concurrent modification by a cmpxchg or
store-release operation, so ensure that the relaxed access in
d_alloc_parallel uses READ_ONCE.
Reported-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If d_alloc_parallel runs concurrently with __d_add, it is possible for
d_alloc_parallel to continuously retry whilst i_dir_seq has been
incremented to an odd value by __d_add:
CPU0:
__d_add
n = start_dir_add(dir);
cmpxchg(&dir->i_dir_seq, n, n + 1) == n
CPU0:
__d_lookup_done(dentry)
hlist_bl_lock
bit_spin_lock(0, (unsigned long *)b); // Never succeeds
CPU1:
if (unlikely(parent->d_inode->i_dir_seq != seq)) {
hlist_bl_unlock(b);
goto retry;
}
Since the simple bit_spin_lock used to implement hlist_bl_lock does not
provide any fairness guarantees, then CPU1 can starve CPU0 of the lock
and prevent it from reaching end_dir_add(dir), therefore CPU1 cannot
exit its retry loop because the sequence number always has the bottom
bit set.
This patch resolves the livelock by not taking hlist_bl_lock in
d_alloc_parallel if the sequence counter is odd, since any subsequent
masked comparison with i_dir_seq will fail anyway.
Cc: Peter Zijlstra <peterz@infradead.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Reported-by: Naresh Madhusudana <naresh.madhusudana@arm.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Although L2 is in halt state, it will be in the active state after
VM entry if the VM entry is vectoring according to SDM 26.6.2 Activity
State. Halting the vcpu here means the event won't be injected to L2
and this decision isn't reported to L1. Thus L0 drops an event that
should be injected to L2.
Commit d02fd6e7d293 ("macvlan: Fix one possible double free") handles
the case when register_netdevice() invokes ndo_uninit() on error and
as a result free the port. But 'macvlan_port_get_rtnl(dev))' check
(returns dev->rx_handler_data), which was added by this commit in order
to prevent double free, is not quite correct:
* for macvlan it always returns NULL because 'lowerdev' is the one that
was used to register rx handler (port) in macvlan_port_create() as
well as to unregister it in macvlan_port_destroy().
* for macvtap it always returns a valid pointer because macvtap registers
its own rx handler before macvlan_common_newlink().
Fixes: d02fd6e7d293 ("macvlan: Fix one possible double free") Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
do_task_stat() calls get_wchan(), which further does unwind_frame().
unwind_frame() restores frame->pc to original value in case function
graph tracer has modified a return address (LR) in a stack frame to hook
a function return. However, if function graph tracer has hit a filtered
function, then we can't unwind it as ftrace_push_return_trace() has
biased the index(frame->graph) with a 'huge negative'
offset(-FTRACE_NOTRACE_DEPTH).
Moreover, arm64 stack walker defines index(frame->graph) as unsigned
int, which can not compare a -ve number.
Similar problem we can have with calling of walk_stackframe() from
save_stack_trace_tsk() or dump_backtrace().
This patch fixes unwind_frame() to test the index for -ve value and
restore index accordingly before we can restore frame->pc.
If no monitoring feature is detected because all monitoring features are
disabled during boot time or there is no monitoring feature in hardware,
creating rdtgroup sub-directory by "mkdir" command reports error:
mkdir: cannot create directory ‘/sys/fs/resctrl/p1’: No such file or directory
But the sub-directory actually is generated and content is correct:
cpus cpus_list schemata tasks
The error is because rdtgroup_mkdir_ctrl_mon() returns non zero value after
the sub-directory is created and the returned value is reported as an error
to user.
Clear the returned value to report to user that the sub-directory is
actually created successfully.
Signed-off-by: Wang Hui <john.wanghui@huawei.com> Signed-off-by: Zhang Yanfei <yanfei.zhang@huawei.com> Signed-off-by: Fenghua Yu <fenghua.yu@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ravi V Shankar <ravi.v.shankar@intel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Cc: Vikas <vikas.shivappa@intel.com> Cc: Xiaochen Shen <xiaochen.shen@intel.com> Link: http://lkml.kernel.org/r/1519356363-133085-1-git-send-email-fenghua.yu@intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Similar to the ancient commit a5fe8e7695dc ("regulatory: add NUL
to alpha2"), add another byte to alpha2 in the request struct so
that when we use nla_put_string(), we don't overrun anything.
If an attempt is made to disable RX checksums, USB adapter is changed
but netdev->features is not, because smsc75xx_set_features() returns a
non zero value.
This throws errors from netdev_rx_csum_fault() :
<devname>: hw csum failure
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Steve Glendinning <steve.glendinning@shawell.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
nfs4_update_server unconditionally releases the nfs_client for the
source server. If migration fails, this can cause the source server's
nfs_client struct to be left with a low reference count, resulting in
use-after-free. Also, adjust reference count handling for ELOOP.
NFS: state manager: migration failed on NFSv4 server nfsvmu10 with error 6
WARNING: CPU: 16 PID: 17960 at fs/nfs/client.c:281 nfs_put_client+0xfa/0x110 [nfs]()
nfs_put_client+0xfa/0x110 [nfs]
nfs4_run_state_manager+0x30/0x40 [nfsv4]
kthread+0xd8/0xf0
dtc recently added PCI bus checks. Fix these warnings:
arch/arm64/boot/dts/cavium/thunder2-99xx.dtb: Warning (pci_bridge): Node /pci missing bus-range for PCI bridge
arch/arm64/boot/dts/cavium/thunder2-99xx.dtb: Warning (unit_address_vs_reg): Node /pci has a reg or ranges property, but no unit name
Signed-off-by: Rob Herring <robh@kernel.org> Cc: Jayachandran C <jnair@caviumnetworks.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If none of the certificates in a SignerInfo's certificate chain match a
trusted key, nor is the last certificate signed by a trusted key, then
pkcs7_validate_trust_one() tries to check whether the SignerInfo's
signature was made directly by a trusted key. But, it actually fails to
set the 'sig' variable correctly, so it actually verifies the last
signature seen. That will only be the SignerInfo's signature if the
certificate chain is empty; otherwise it will actually be the last
certificate's signature.
This is not by itself a security problem, since verifying any of the
certificates in the chain should be sufficient to verify the SignerInfo.
Still, it's not working as intended so it should be fixed.
Fix it by setting 'sig' correctly for the direct verification case.
Fixes: 757932e6da6d ("PKCS#7: Handle PKCS#7 messages that contain no X.509 certs") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
test_maps contains a series of stress tests, and previously it will break the
rest tests when it failed to alloc memory.
-----------------------
Failed to create hashmap key=8 value=262144 'Cannot allocate memory'
Failed to create hashmap key=16 value=262144 'Cannot allocate memory'
Failed to create hashmap key=8 value=262144 'Cannot allocate memory'
Failed to create hashmap key=8 value=262144 'Cannot allocate memory'
test_maps: test_maps.c:955: run_parallel: Assertion `status == 0' failed.
Aborted
not ok 1..3 selftests: test_maps [FAIL]
-----------------------
after this patch, the rest tests will be continue when it occurs an ENOMEM failure
CC: Alexei Starovoitov <alexei.starovoitov@gmail.com> CC: Philip Li <philip.li@intel.com> Suggested-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Li Zhijian <zhijianx.li@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When we terminate driver I/O (because we need to stop using a certain
channel path) we also need to ensure that a timer (which may have been
set up using ccw_device_start_timeout) is cleared.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When a timeout occurs for users of ccw_device_start_timeout
we will stop the IO and call the drivers int handler with
the irb pointer set to ERR_PTR(-ETIMEDOUT). Sometimes
however we'd set the irb pointer to ERR_PTR(-EIO) which is
not intended. Just set the correct value in all codepaths.
Reported-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There are cases a device driver can't start IO because the device is
currently in use by cio. In this case the device driver is notified
when the device is usable again.
Using ccw_device_start_timeout we would set the timeout (and change
an existing timeout) before we test for internal usage. Worst case
this could lead to an unexpected timer deletion.
Fix this by setting the timeout after we test for internal usage.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
I am using SECCOMP to filter syscalls on a ppc32 platform, and noticed
that the JIT compiler was failing on the BPF even though the
interpreter was working fine.
The issue was that the compiler was missing one of the instructions
used by SECCOMP, so here is a patch to enable JIT for that
instruction.
Fixes: eb84bab0fb38 ("ppc: Kconfig: Enable BPF JIT on ppc32") Signed-off-by: Mark Lord <mlord@pobox.com> Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If power domain information are missing in the device tree, no
power domains get initialized. However, imx_gpc_remove tries to
remove power domains always in the old DT binding case. Only
remove power domains when imx_gpc_probe initialized them in
first place.
Fixes: 721cabf6c660 ("soc: imx: move PGC handling to a new GPC driver") Signed-off-by: Stefan Agner <stefan@agner.ch> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Looking at functions with large stack frames across all architectures
led me discovering that BUG() suffers from the same problem as
fortify_panic(), which I've added a workaround for already.
In short, variables that go out of scope by calling a noreturn function
or __builtin_unreachable() keep using stack space in functions
afterwards.
A workaround that was identified is to insert an empty assembler
statement just before calling the function that doesn't return. I'm
adding a macro "barrier_before_unreachable()" to document this, and
insert calls to that in all instances of BUG() that currently suffer
from this problem.
The files that saw the largest change from this had these frame sizes
before, and much less with my patch:
fs/ext4/inode.c:82:1: warning: the frame size of 1672 bytes is larger than 800 bytes [-Wframe-larger-than=]
fs/ext4/namei.c:434:1: warning: the frame size of 904 bytes is larger than 800 bytes [-Wframe-larger-than=]
fs/ext4/super.c:2279:1: warning: the frame size of 1160 bytes is larger than 800 bytes [-Wframe-larger-than=]
fs/ext4/xattr.c:146:1: warning: the frame size of 1168 bytes is larger than 800 bytes [-Wframe-larger-than=]
fs/f2fs/inode.c:152:1: warning: the frame size of 1424 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_core.c:1195:1: warning: the frame size of 1068 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_core.c:395:1: warning: the frame size of 1084 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_ftp.c:298:1: warning: the frame size of 928 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_ftp.c:418:1: warning: the frame size of 908 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_lblcr.c:718:1: warning: the frame size of 960 bytes is larger than 800 bytes [-Wframe-larger-than=]
drivers/net/xen-netback/netback.c:1500:1: warning: the frame size of 1088 bytes is larger than 800 bytes [-Wframe-larger-than=]
In case of ARC and CRIS, it turns out that the BUG() implementation
actually does return (or at least the compiler thinks it does),
resulting in lots of warnings about uninitialized variable use and
leaving noreturn functions, such as:
block/cfq-iosched.c: In function 'cfq_async_queue_prio':
block/cfq-iosched.c:3804:1: error: control reaches end of non-void function [-Werror=return-type]
include/linux/dmaengine.h: In function 'dma_maxpq':
include/linux/dmaengine.h:1123:1: error: control reaches end of non-void function [-Werror=return-type]
This makes them call __builtin_trap() instead, which should normally
dump the stack and kill the current process, like some of the other
architectures already do.
I tried adding barrier_before_unreachable() to panic() and
fortify_panic() as well, but that had very little effect, so I'm not
submitting that patch.
Vineet said:
: For ARC, it is double win.
:
: 1. Fixes 3 -Wreturn-type warnings
:
: | ../net/core/ethtool.c:311:1: warning: control reaches end of non-void function
: [-Wreturn-type]
: | ../kernel/sched/core.c:3246:1: warning: control reaches end of non-void function
: [-Wreturn-type]
: | ../include/linux/sunrpc/svc_xprt.h:180:1: warning: control reaches end of
: non-void function [-Wreturn-type]
:
: 2. bloat-o-meter reports code size improvements as gcc elides the
: generated code for stack return.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=82365 Link: http://lkml.kernel.org/r/20171219114112.939391-1-arnd@arndb.de Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Vineet Gupta <vgupta@synopsys.com> [arch/arc] Tested-by: Vineet Gupta <vgupta@synopsys.com> [arch/arc] Cc: Mikael Starvik <starvik@axis.com> Cc: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Christopher Li <sparse@chrisli.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Kees Cook <keescook@chromium.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Will Deacon <will.deacon@arm.com> Cc: "Steven Rostedt (VMware)" <rostedt@goodmis.org> Cc: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When configuring virtio_net to use the code path 'receive_small()',
in-order to get correct XDP_REDIRECT support, I discovered TCP packets
would get silently dropped when loading an XDP program action XDP_PASS.
The bug seems to be that receive_small() when XDP is loaded check that
hdr->hdr.flags is zero, which seems wrong as hdr.flags contains the
flags VIRTIO_NET_HDR_F_* :
#define VIRTIO_NET_HDR_F_NEEDS_CSUM 1 /* Use csum_start, csum_offset */
#define VIRTIO_NET_HDR_F_DATA_VALID 2 /* Csum is valid */
TCP got dropped as it had the VIRTIO_NET_HDR_F_DATA_VALID flag set.
The flags that are relevant here are the VIRTIO_NET_HDR_GSO_* flags
stored in hdr->hdr.gso_type. Thus, the fix is just check that none of
the gso_type flags have been set.
Fixes: bb91accf2733 ("virtio-net: XDP support for small buffers") Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
gcc warns about a possible overflow of the kmem_cache string, when adding
four characters to a string of the same length:
drivers/md/raid5.c: In function 'setup_conf':
drivers/md/raid5.c:2207:34: error: '-alt' directive writing 4 bytes into a region of size between 1 and 32 [-Werror=format-overflow=]
sprintf(conf->cache_name[1], "%s-alt", conf->cache_name[0]);
^~~~
drivers/md/raid5.c:2207:2: note: 'sprintf' output between 5 and 36 bytes into a destination of size 32
sprintf(conf->cache_name[1], "%s-alt", conf->cache_name[0]);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
If I'm counting correctly, we need 11 characters for the fixed part
of the string and 18 characters for a 64-bit pointer (when no gendisk
is used), so that leaves three characters for conf->level, which should
always be sufficient.
This makes the code use snprintf() with the correct length, to
make the code more robust against changes, and to get the compiler
to shut up.
In commit f4be6b43f1ac ("md/raid5: ensure we create a unique name for
kmem_cache when mddev has no gendisk") from 2010, Neil said that
the pointer could be removed "shortly" once devices without gendisk
are disallowed. I have no idea if that happened, but if it did, that
should probably be changed as well.
Continuing along with the fight against smp_read_barrier_depends() [1]
(or rather, against its improper use), add an unconditional barrier to
cmpxchg. This guarantees that dependency ordering is preserved when a
dependency is headed by an unsuccessful cmpxchg. As it turns out, the
change could enable further simplification of LKMM as proposed in [2].
During driver unload, the driver proceeds with cleanup
without waiting for the scheduled events. So the device
pointers get freed up and driver crashes when the events
are scheduled later.
Flush the bnxt_re_task work queue before starting
device removal.
The ID_AA64DFR0_EL1.PMUVer field doesn't follow the usual ID registers
scheme. While value 0xf indicates a non-architected PMU is implemented,
values 0x1 to 0xe indicate an increasingly featureful architected PMU,
as if the field were unsigned.
For more details, see ARM DDI 0487C.a, D10.1.4, "Alternative ID scheme
used for the Performance Monitors Extension version".
Currently, we treat the field as signed, and erroneously bail out for
values 0x8 to 0xe. Let's correct that.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Reviewed-by: Robin Murphy <robin.murphy@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The plane buffer address/stride/height was incorrectly updated in the
plane_atomic_update operation instead of the vsync irq.
This patch delays this operation in the vsync irq along with the
other plane delayed setup.
This issue was masked using legacy framebuffer and X11 modesetting, but
is clearly visible using gbm rendering when buffer is submitted late after
vblank, like using software decoding and OpenGL rendering in Kodi.
With this patch, tearing and other artifacts disappears completely.
Cc: Michal Lazo <michal.lazo@gmail.com> Fixes: bbbe775ec5b5 ("drm: Add support for Amlogic Meson Graphic Controller") Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/1518689976-23292-1-git-send-email-narmstrong@baylibre.com Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The exynos DRM driver uses real-time 'struct timeval' values
for exporting its timestamps to user space. This has multiple
problems:
1. signed seconds overflow in y2038
2. the 'struct timeval' definition is deprecated in the kernel
3. time may jump or go backwards after a 'settimeofday()' syscall
4. other DRM timestamps are in CLOCK_MONOTONIC domain, so they
can't be compared
5. exporting microseconds requires a division by 1000, which may
be slow on some architectures.
The code existed in two places before, but the IPP portion was
removed in 8ded59413ccc ("drm/exynos: ipp: Remove Exynos DRM
IPP subsystem"), so we no longer need to worry about it.
Ideally timestamps should just use 64-bit nanoseconds instead, but
of course we can't change that now. Instead, this tries to address
the first four points above by using monotonic 'timespec' values.
According to Tobias Jakobi, user space doesn't care about the
timestamp at the moment, so we can change the format. Even if
there is something looking at them, it will work just fine with
monotonic times as long as the application only looks at the
relative values between two events.
In the case of 'recover', an r10bio with R10BIO_WriteError &
R10BIO_IsRecover will be progressed by handle_write_completed().
This function traverses all r10bio->devs[copies].
If devs[m].repl_bio != NULL, it thinks conf->mirrors[dev].replacement
is also not NULL. However, this is not always true.
When there is an rdev of raid10 has replacement, then each r10bio
->devs[m].repl_bio != NULL in conf->r10buf_pool. However, in 'recover',
even if corresponded replacement is NULL, it doesn't clear r10bio
->devs[m].repl_bio, resulting in replacement NULL deference.
This bug was introduced when replacement support for raid10 was
added in Linux 3.3.
As NeilBrown suggested:
Elsewhere the determination of "is this device part of the
resync/recovery" is made by resting bio->bi_end_io.
If this is end_sync_write, then we tried to write here.
If it is NULL, then we didn't try to write.
In case an ADDBA request is received while there is already
an ongoing BA sessions with the same parameters, i.e., update
flow, an ADBBA response with decline status was sent twice. Fix it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Some APs include a non global operating class in their extended channel
switch information element. In such a case, as the operating class is not
known, mac80211 would decide to disconnect.
However the specification states that the operating class needs to be
taken from Annex E, but it does not specify from which table it should be
taken, so it is valid for an AP to use a non global operating class.
To avoid possibly unneeded disconnection, in such a case ignore the
operating class and assume that the current band is used, and if the
resulting channel and band configuration is invalid disconnect.
Signed-off-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>