drm/exynos: remove DRM_FORMAT_NV12M from plane module
this patch removes DRM_FORMAT_NV12M from plane module because this format
is same as DRM_FORMAT_NV12. DRM_FORMAT_NV12M will be identified by
mode_cmd->handles and mode_cmd->offsets fields internally.
Sachin Kamat [Fri, 31 Aug 2012 10:20:48 +0000 (15:50 +0530)]
drm/exynos: Add missing braces around sizeof in exynos_mixer.c
Fixes the following checkpatch warnings:
WARNING: sizeof filter_y_horiz_tap8 should be sizeof(filter_y_horiz_tap8)
WARNING: sizeof filter_y_vert_tap4 should be sizeof(filter_y_vert_tap4)
WARNING: sizeof filter_cr_horiz_tap4 should be sizeof(filter_cr_horiz_tap4)
Sachin Kamat [Fri, 31 Aug 2012 10:20:47 +0000 (15:50 +0530)]
drm/exynos: Add missing braces around sizeof in exynos_hdmi.c
Fixes the following checkpatch warnings:
WARNING: sizeof *res should be sizeof(*res)
WARNING: sizeof res->regul_bulk[0] should be sizeof(res->regul_bulk[0])
WARNING: sizeof *res should be sizeof(*res)
Sachin Kamat [Mon, 6 Aug 2012 06:46:17 +0000 (12:16 +0530)]
drm/exynos: Remove redundant check in exynos_drm_fimd.c file
devm_request_and_ioremap function checks the validity of the
pointer returned by platform_get_resource. Hence an additional check
in the probe function is not necessary.
Sachin Kamat [Mon, 6 Aug 2012 06:46:16 +0000 (12:16 +0530)]
drm/exynos: Remove redundant check in exynos_hdmi.c file
devm_request_and_ioremap function checks the validity of the
pointer returned by platform_get_resource. Hence an additional check
in the probe function is not necessary.
Dave Airlie [Thu, 13 Sep 2012 01:07:31 +0000 (11:07 +1000)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Daniel writes:
"Nothing really major at all:
- fixup edp setup sequence (Dave)
- disable sdvo hotplug for real, this is a fixup for a messed-up
regression fixer (Jani)
- don't expose dysfunctional backlight driver (Jani)
- properly init spinlock (only used by hsw/vlv code) from Alexander
Shishkin"
along with a couple of more fixes on top.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: fix up the IBX transcoder B check
drm/i915: set the right gen3 flip_done mode also at resume
drm/i915: initialize dpio_lock spin lock
drm/i915: do not expose a dysfunctional backlight interface to userspace
drm/i915: only enable sdvo hotplug irq if needed
drm/i915/edp: get the panel delay before powering up
Merge branch 'for-3.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fixes from Tejun Heo:
"It's later than I'd like but well the timing just didn't work out this
time.
There are three bug fixes. One from before 3.6-rc1 and two from the
new CPU hotplug code. Kudos to Lai for discovering all of them and
providing fixes.
* Atomicity bug when clearing a flag and setting another. The two
operation should have been atomic but wasn't. This bug has existed
for a long time but is unlikely to have actually happened. Fix is
safe. Marked for -stable.
* If CPU hotplug cycles happen back-to-back before workers finish the
previous cycle, the states could get out of sync and it could get
stuck. Fixed by waiting for workers to complete before finishing
hotplug cycle.
* While CPU hotplug is in progress, idle workers could be depleted
which can then lead to deadlock. I think both happening together
is highly unlikely but still better to fix it and the fix isn't too
scary.
There's another workqueue related regression which reported a few days
ago:
https://bugzilla.kernel.org/show_bug.cgi?id=47301
It's a bit of head scratcher but there is a semi-reliable reproduce
case, so I'm hoping to resolve it soonish."
* 'for-3.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: fix possible idle worker depletion across CPU hotplug
workqueue: restore POOL_MANAGING_WORKERS
workqueue: fix possible deadlock in idle worker rebinding
workqueue: move WORKER_REBIND clearing in rebind_workers() to the end of the function
workqueue: UNBOUND -> REBIND morphing in rebind_workers() should be atomic
Pull crypto fixes from Herbert Xu:
"This fixes the authenc self-test crash as well as a missing export of
a symbol used by a module."
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: authenc - Fix crash with zero-length assoc data
crypto/caam: Export gen_split_key symbol for other modules
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lliubbo/blackfin
Pull blackfin updates from Bob Liu:
"One kbuild and a smp build fix."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lliubbo/blackfin:
kbuild: add symbol prefix arg to kallsyms
blackfin: smp: adapt to generic smp helpers
drm/i915: assert that the IBX port transcoder select w/a is implemented
Unfortunately I've failed to notice that these checks are not just
called for the port that is about to be disabled, but for all (which
makes sense for an assert ...), and the WARN missfired when disabling
another pipe than the one with the dp port.
Hence also check whether the port is actually disabled.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=54688 Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Herbert Xu [Tue, 11 Sep 2012 04:05:45 +0000 (12:05 +0800)]
crypto: authenc - Fix crash with zero-length assoc data
The authenc code doesn't deal with zero-length associated data
correctly and ends up constructing a zero-length sg entry which
causes a crash when it's fed into the crypto system.
This patch fixes this by avoiding the code-path that triggers
the SG construction if we have no associated data.
This isn't the most optimal fix as it means that we'll end up
using the fallback code-path even when we could still execute
the digest function. However, this isn't a big deal as nobody
but the test path would supply zero-length associated data.
James Hogan [Thu, 6 Sep 2012 21:11:25 +0000 (22:11 +0100)]
kbuild: add symbol prefix arg to kallsyms
Commit 1f2bfbd00e466ff3489b2ca5cc75b1cccd14c123 ("kbuild: link of
vmlinux moved to a script") introduced in v3.5-rc1 broke kallsyms on
architectures which have symbol prefixes.
The --symbol-prefix argument used to be added to the KALLSYMS command
line from the architecture Makefile, however this isn't picked up by the
new scripts/link-vmlinux.sh. This resulted in symbols like
kallsyms_addresses being added which weren't correctly overriding the
weak symbols such as _kallsyms_addresses. These could then trigger
BUG_ONs in kallsyms code.
This is fixed by removing the KALLSYMS addition from the architecture
Makefile, and using CONFIG_SYMBOL_PREFIX in the link-vmlinux.sh script
to determine whether to add the --symbol-prefix argument.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Bob Liu <lliubbo@gmail.com>
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"I had actually prepared this fix set before I left for KS + Plumbers,
so it's been incubating much longer than it should have. I'll be
picking up my three week backlog this week, so more fixes will then be
forthcoming
This set consist of three minor and one fairly major (the device not
ready causing offlining problem which is a serious regression
introduced by the media change update) fixes.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] Fix 'Device not ready' issue on mpt2sas
[SCSI] scsi_lib: fix scsi_io_completion's SG_IO error propagation
[SCSI] megaraid_sas: Move poll_aen_lock initializer
[SCSI] mpt2sas: Fix for Driver oops, when loading driver with max_queue_depth command line option to a very small value
Merge tag 'kvm-3.6-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Avi Kivity:
"A trio of KVM fixes: incorrect lookup of guest cpuid, an uninitialized
variable fix, and error path cleanup fix."
* tag 'kvm-3.6-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: fix error paths for failed gfn_to_page() calls
KVM: x86: Check INVPCID feature bit in EBX of leaf 7
KVM: PIC: fix use of uninitialised variable.
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull UDF and ext3 fixes from Jan Kara:
"One UDF data corruption fix and one ext3 fix where we didn't write
everything to disk on fsync in one corner case."
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
udf: Fix data corruption for files in ICB
ext3: Fix fdatasync() for files with only i_size changes
Lai Jiangshan [Mon, 10 Sep 2012 17:03:44 +0000 (10:03 -0700)]
workqueue: fix possible idle worker depletion across CPU hotplug
To simplify both normal and CPU hotplug paths, worker management is
prevented while CPU hoplug is in progress. This is achieved by CPU
hotplug holding the same exclusion mechanism used by workers to ensure
there's only one manager per pool.
If someone else seems to be performing the manager role, workers
proceed to execute work items. CPU hotplug using the same mechanism
can lead to idle worker depletion because all workers could proceed to
execute work items while CPU hotplug is in progress and CPU hotplug
itself wouldn't actually perform the worker management duty - it
doesn't guarantee that there's an idle worker left when it releases
management.
This idle worker depletion, under extreme circumstances, can break
forward-progress guarantee and thus lead to deadlock.
This patch fixes the bug by using separate mechanisms for manager
exclusion among workers and hotplug exclusion. For manager exclusion,
POOL_MANAGING_WORKERS which was restored by the previous patch is
used. pool->manager_mutex is now only used for exclusion between the
elected manager and CPU hotplug. The elected manager won't proceed
without holding pool->manager_mutex.
This ensures that the worker which won the manager position can't skip
managing while CPU hotplug is in progress. It will block on
manager_mutex and perform management after CPU hotplug is complete.
Note that hotplug may happen while waiting for manager_mutex. A
manager isn't either on idle or busy list and thus the hoplug code
can't unbind/rebind it. Make the manager handle its own un/rebinding.
tj: Updated comment and description.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com> Signed-off-by: Tejun Heo <tj@kernel.org>
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Just noticed I hadn't send these out, nothing majorly urgent, I know
AMD guys have some regression fixes coming soon.
This contains:
2 nouveau fixes so it loads on the retina MBP systems properly,
2 vmwgfx fixes to load the driver earlier, and allow distros config it
1 error->debug fix in ast
and Keith was playing with 32-on-64 and decided we may as well stick
the compat ioctl in all the drivers. It fixes udl for him."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/vmwgfx: add MODULE_DEVICE_TABLE so vmwgfx loads at boot
drm/vmwgfx: allow a kconfig option to choose if fbcon is enabled
drm: use drm_compat_ioctl for 32-bit apps
drm/ast: drop debug level on error printk
drm/nv50-/gpio: initialise to vbios defaults during init
drm/nvd0/disp: hopefully fix selection of 6/8bpc mode on DP outputs
Lai Jiangshan [Mon, 10 Sep 2012 17:03:33 +0000 (10:03 -0700)]
workqueue: restore POOL_MANAGING_WORKERS
This patch restores POOL_MANAGING_WORKERS which was replaced by
pool->manager_mutex by 6037315269 "workqueue: use mutex for global_cwq
manager exclusion".
There's a subtle idle worker depletion bug across CPU hotplug events
and we need to distinguish an actual manager and CPU hotplug
preventing management. POOL_MANAGING_WORKERS will be used for the
former and manager_mutex the later.
This patch just lays POOL_MANAGING_WORKERS on top of the existing
manager_mutex and doesn't introduce any synchronization changes. The
next patch will update it.
Note that this patch fixes a non-critical anomaly where
too_many_workers() may return %true spuriously while CPU hotplug is in
progress. While the issue could schedule idle timer spuriously, it
didn't trigger any actual misbehavior.
tj: Rewrote patch description.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com> Signed-off-by: Tejun Heo <tj@kernel.org>
It caused by release kvm->arch.ept_identity_map_addr which is the
error page.
The parent thread can send KILL signal to the vcpu thread when it was
exiting which stops faulting pages and potentially allocating memory.
So gfn_to_pfn/gfn_to_page may fail at this time
Fixed by checking the page before it is used
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com> Signed-off-by: Avi Kivity <avi@redhat.com>
Jean Delvare [Mon, 10 Sep 2012 08:14:02 +0000 (10:14 +0200)]
i2c-core: Fix for lockdep validator
If kernel is compiled with CONFIG_PROVE_LOCKING the
validator raises an error when a multiplexer is removed
via sysfs and sub-clients are connected to it. This is a
false positive.
Documentation/lockdep-design.txt recommends to handle this
via calls to mutex_lock_nested().
Based on an earlier fix from Michael Lawnick.
Note that the extra code resolves to nothing unless
CONFIG_DEBUG_LOCK_ALLOC=y.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Michael Lawnick <ml.lawnick@gmx.de>
Axel Lin [Mon, 10 Sep 2012 08:14:02 +0000 (10:14 +0200)]
i2c-designware: Fix build error if CONFIG_I2C_DESIGNWARE_PLATFORM=y && CONFIG_I2C_DESIGNWARE_PCI=y
This patch adds config I2C_DESIGNWARE_CORE in Kconfig, and let
I2C_DESIGNWARE_PLATFORM and I2C_DESIGNWARE_PCI select I2C_DESIGNWARE_CORE.
Because both I2C_DESIGNWARE_PLATFORM and I2C_DESIGNWARE_PCI can be built as
built-in or module, we also need to export the functions in i2c-designware-core.
This fixes below build error when CONFIG_I2C_DESIGNWARE_PLATFORM=y &&
CONFIG_I2C_DESIGNWARE_PCI=y:
LD drivers/i2c/busses/built-in.o
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_clear_int':
i2c-designware-core.c:(.text+0xa10): multiple definition of `i2c_dw_clear_int'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x928): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_init':
i2c-designware-core.c:(.text+0x178): multiple definition of `i2c_dw_init'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x90): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `dw_readl':
i2c-designware-core.c:(.text+0xe8): multiple definition of `dw_readl'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x0): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_isr':
i2c-designware-core.c:(.text+0x724): multiple definition of `i2c_dw_isr'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x63c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_xfer':
i2c-designware-core.c:(.text+0x4b0): multiple definition of `i2c_dw_xfer'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x3c8): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_is_enabled':
i2c-designware-core.c:(.text+0x9d4): multiple definition of `i2c_dw_is_enabled'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8ec): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `dw_writel':
i2c-designware-core.c:(.text+0x124): multiple definition of `dw_writel'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x3c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_xfer_msg':
i2c-designware-core.c:(.text+0x2e8): multiple definition of `i2c_dw_xfer_msg'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x200): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_enable':
i2c-designware-core.c:(.text+0x9c8): multiple definition of `i2c_dw_enable'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8e0): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_read_comp_param':
i2c-designware-core.c:(.text+0xa24): multiple definition of `i2c_dw_read_comp_param'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x93c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_disable':
i2c-designware-core.c:(.text+0x9dc): multiple definition of `i2c_dw_disable'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8f4): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_func':
i2c-designware-core.c:(.text+0x710): multiple definition of `i2c_dw_func'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x628): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_disable_int':
i2c-designware-core.c:(.text+0xa18): multiple definition of `i2c_dw_disable_int'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x930): first defined here
make[3]: *** [drivers/i2c/busses/built-in.o] Error 1
make[2]: *** [drivers/i2c/busses] Error 2
make[1]: *** [drivers/i2c] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Jean Delvare <khali@linux-fr.org> Tested-by: Jiri Slaby <jslaby@suse.cz> Cc: stable@vger.kernel.org [3.2+]
Merge branch 'fixes-for-3.6' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping
Pull DMA-mapping fixes from Marek Szyprowski:
"Another set of fixes for ARM dma-mapping subsystem.
Commit e9da6e9905e6 replaced custom consistent buffer remapping code
with generic vmalloc areas. It however introduced some regressions
caused by limited support for allocations in atomic context. This
series contains fixes for those regressions.
For some subplatforms the default, pre-allocated pool for atomic
allocations turned out to be too small, so a function for setting its
size has been added.
Another set of patches adds support for atomic allocations to
IOMMU-aware DMA-mapping implementation.
The last part of this pull request contains two fixes for Contiguous
Memory Allocator, which relax too strict requirements."
* 'fixes-for-3.6' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: dma-mapping: IOMMU allocates pages from atomic_pool with GFP_ATOMIC
ARM: dma-mapping: Introduce __atomic_get_pages() for __iommu_get_pages()
ARM: dma-mapping: Refactor out to introduce __in_atomic_pool
ARM: dma-mapping: atomic_pool with struct page **pages
ARM: Kirkwood: increase atomic coherent pool size
ARM: DMA-Mapping: print warning when atomic coherent allocation fails
ARM: DMA-Mapping: add function for setting coherent pool size from platform code
ARM: relax conditions required for enabling Contiguous Memory Allocator
mm: cma: fix alignment requirements for contiguous regions
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input subsystem updates from Dmitry Torokhov.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - add support for EMR on Cintiq 24HD touch
Input: i8042 - add Gigabyte T1005 series netbooks to noloop table
Input: imx_keypad - reset the hardware before enabling
Input: edt-ft5x06 - fix build error when compiling wthout CONFIG_DEBUG_FS
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
[Jani: move the init next to the other spin lock inits] Signed-off-by: Jani Nikula <jani.nikula@intel.com> Acked-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Merge branch 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID updates from Jiri Kosina:
"It contains a fix for Eaton Ellipse MAX UPS from Alan Stern,
performance improvement (not processing debug data if noone is
interested), by Henrik Rydberg, and allowing tpkbd-driven devices to
work even with generic driver in a crippled mode, by Andres Freund."
* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
HID: Only dump input if someone is listening
HID: add NOGET quirk for Eaton Ellipse MAX UPS
Andres Freund [Thu, 30 Aug 2012 12:37:14 +0000 (14:37 +0200)]
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
c1dcad2d32d0252e8a3023d20311b52a187ecda3 added a new driver configured by
HID_LENOVO_TPKBD but made the hid_have_special_driver entry non-optional which
lead to a recognized but non-working device if the new driver wasn't
configured (which is the correct default).
Signed-off-by: Andres Freund <andres@anarazel.de> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Merge tag 'stable/for-linus-3.6-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
* Fix for TLB flushing introduced in v3.6
* Fix Xen-SWIOTLB not using proper DMA mask - device had 64bit but
in a 32-bit kernel we need to allocate for coherent pages from a
32-bit pool.
* When trying to re-use P2M nodes we had a one-off error and triggered
a BUG_ON check with specific CONFIG_ option.
* When doing FLR in Xen-PCI-backend we would first do FLR then save the
PCI configuration space. We needed to do it the other way around.
* tag 'stable/for-linus-3.6-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pciback: Fix proper FLR steps.
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
Merge tag '3.6-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Power management
- PCI/PM: Enable D3/D3cold by default for most devices
- PCI/PM: Keep parent bridge active when probing device
- PCI/PM: Fix config reg access for D3cold and bridge suspending
- PCI/PM: Add ABI document for sysfs file d3cold_allowed
Core
- PCI: Don't print anything while decoding is disabled"
* tag '3.6-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Don't print anything while decoding is disabled
PCI/PM: Add ABI document for sysfs file d3cold_allowed
PCI/PM: Fix config reg access for D3cold and bridge suspending
PCI/PM: Keep parent bridge active when probing device
PCI/PM: Enable D3/D3cold by default for most devices
Signed-off-by: Ben Collins <ben.c@servergy.com> Cc: Yuan Kang <Yuan.Kang@freescale.com> Acked-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC bug fixes from Olof Johansson:
"Mostly Renesas and Atmel bugfixes this time, targeting boot and build
problems. A couple of patches for gemini and kirkwood as well. On a
whole nothing very controversial."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: gemini: fix the gemini build
ARM: shmobile: armadillo800eva: enable rw rootfs mount
ARM: Kirkwood: Fix 'SZ_1M' undeclared here for db88f6281-bp-setup.c
ARM: shmobile: mackerel: fixup usb module order
ARM: shmobile: armadillo800eva: fixup: sound card detection order
ARM: shmobile: marzen: fixup smsc911x id for regulator
ARM: at91/feature-removal-schedule: delay at91_mci removal
ARM: mach-shmobile: armadillo800eva: Enable power button as wakeup source
ARM: mach-shmobile: armadillo800eva: Fix GPIO buttons descriptions
ARM: at91/dts: remove partial parameter in at91sam9g25ek.dts
ARM: at91/clock: fix PLLA overclock warning
ARM: at91: fix rtc-at91sam9 irq issue due to sparse irq support
ARM: at91: fix system timer irq issue due to sparse irq support
ARM: shmobile: sh73a0: fixup RELOC_BASE of intca_irq_pins_desc
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull a hwmon fix from Guenter Roeck:
"One patch, fixing DIV_ROUND_CLOSEST to support negative dividends.
While the changes are not in the drivers/hwmon directory, the problem
primarily affects hwmon drivers, and it makes sense to push the patch
through the hwmon tree."
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
linux/kernel.h: Fix DIV_ROUND_CLOSEST to support negative dividends
Merge branch 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild fixes from Michal Marek:
"These are two fixes that should go into 3.6. The link-vmlinux.sh one
is obvious.
The other one fixes make firmware_install with certain configurations,
where a file in the toplevel firmware tree gets installed first, and
$(INSTALL_FW_PATH)/$$(dir <file>) results in /lib/firmware/./, which
confuses make 3.82 for some reason."
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
firmware: fix directory creation rule matching with make 3.82
link-vmlinux.sh: Fix stray "echo" in error message
When we do FLR and save PCI config we did it in the wrong order.
The end result was that if a PCI device was unbind from
its driver, then binded to xen-pciback, and then back to its
driver we would get:
Merge tag 'mmc-fixes-for-3.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC fixes from Chris Ball:
- a firmware bug on several Samsung MoviNAND eMMC models causes
permanent corruption on the device when secure erase and secure trim
requests are made, so we disable those requests on these eMMC devices.
- atmel-mci: fix a hang with some SD cards by waiting for not-busy flag.
- dw_mmc: low-power mode breaks SDIO interrupts; fix PIO error handling;
fix handling of error interrupts.
- mxs-mmc: fix deadlocks; fix compile error due to dma.h arch change.
- omap: fix broken PIO mode causing memory corruption.
- sdhci-esdhc: fix card detection.
* tag 'mmc-fixes-for-3.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: omap: fix broken PIO mode
mmc: card: Skip secure erase on MoviNAND; causes unrecoverable corruption.
mmc: dw_mmc: Disable low power mode if SDIO interrupts are used
mmc: dw_mmc: fix error handling in PIO mode
mmc: dw_mmc: correct mishandling error interrupt
mmc: dw_mmc: amend using error interrupt status
mmc: atmel-mci: not busy flag has also to be used for read operations
mmc: sdhci-esdhc: break out early if clock is 0
mmc: mxs-mmc: fix deadlock caused by recursion loop
mmc: mxs-mmc: fix deadlock in SDIO IRQ case
mmc: bfin_sdh: fix dma_desc_array build error
arch/um/os-Linux/time.c: In function 'deliver_alarm':
arch/um/os-Linux/time.c:117:3: error: too few arguments to function 'alarm_handler'
arch/um/os-Linux/internal.h:1:6: note: declared here
The error was introduced by commit d3c1cfcd ("um: pass siginfo to guest
process") in 3.6-rc1.
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Benjamin Herrenschmidt:
"Here are a few fixes for 3.6 that were piling up while I was away or
busy (I was mostly MIA a week or two before San Diego).
Some fixes from Anton fixing up issues with our relatively new DSCR
control feature, and a few other fixes that are either regressions or
bugs nasty enough to warrant not waiting."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
powerpc/powernv: Always go into nap mode when CPU is offline
powerpc: Give hypervisor decrementer interrupts their own handler
powerpc/vphn: Fix arch_update_cpu_topology() return value
Merge tag 'gpio-fixes-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"These are some GPIO regression fixes for v3.6:
- Erroneous debug message from of_get_named_gpio_flags()
- Make sure the MC9S08DZ60 GPIO driver depend on I2C being compiled
in (not module) or allmodconfig breaks.
- Check return value from irq_alloc_descs() in the Emma Mobile GPIO
driver.
- Assign the owner field for the rdc321x driver so the module won't
be removed if it has active GPIOs."
* tag 'gpio-fixes-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: rdc321x: Prevent removal of modules exporting active GPIOs
gpio: em: Fix checking return value of irq_alloc_descs
gpio: mc9s08dz60: Fix build error if I2C=m
gpio: Fix debug message in of_get_named_gpio_flags()
Merge tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"There are nothing scaring, contains only small fixes for HD-audio and
USB-audio:
- EPSS regression fix and GPIO fix for HD-audio IDT codecs
- A series of USB-audio regression fixes that are found since 3.5
kernel"
* tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: snd-usb: fix cross-interface streaming devices
ALSA: snd-usb: fix calls to next_packet_size
ALSA: snd-usb: restore delay information
ALSA: snd-usb: use list_for_each_safe for endpoint resources
ALSA: snd-usb: Fix URB cancellation at stream start
ALSA: hda - Don't trust codec EPSS bit for IDT 92HD83xx & co
ALSA: hda - Avoid unnecessary parameter read for EPSS
ALSA: hda - Do not set GPIOs for speakers on IDT if there are no speakers
* tag 'fbdev-fixes-for-3.6-1' of git://github.com/schandinat/linux-2.6:
OMAPFB: fix framebuffer console colors
OMAPDSS: Fix SDI PLL locking
video: mb862xxfb: prevent divide by zero bug
drivers/video/auo_k190x.c: drop kfree of devm_kzalloc's data
fbcon: Fix bit_putcs() call to kmalloc(s, GFP_KERNEL)
fbcon: prevent possible buffer overflow.
Merge tag 'upstream-3.6-rc5' of git://git.infradead.org/linux-ubi
Pull ubi fix from Artem Bityutskiy:
"A single small fix for memory deallocation: we allocated memory using
'kmem_cache_alloc()' but were freeing it using 'kfree()' in some
cases. Now we fix this by using 'kmem_cache_free()' instead."
* tag 'upstream-3.6-rc5' of git://git.infradead.org/linux-ubi:
UBI: fix a horrible memory deallocation bug
Fix order of arguments to compat_put_time[spec|val]
Commit 644595f89620 ("compat: Handle COMPAT_USE_64BIT_TIME in
net/socket.c") introduced a bug where the helper functions to take
either a 64-bit or compat time[spec|val] got the arguments in the wrong
order, passing the kernel stack pointer off as a user pointer (and vice
versa).
Because of the user address range check, that in turn then causes an
EFAULT due to the user pointer range checking failing for the kernel
address. Incorrectly resuling in a failed system call for 32-bit
processes with a 64-bit kernel.
On odder architectures like HP-PA (with separate user/kernel address
spaces), it can be used read kernel memory.
workqueue: fix possible deadlock in idle worker rebinding
Currently, rebind_workers() and idle_worker_rebind() are two-way
interlocked. rebind_workers() waits for idle workers to finish
rebinding and rebound idle workers wait for rebind_workers() to finish
rebinding busy workers before proceeding.
Unfortunately, this isn't enough. The second wait from idle workers
is implemented as follows.
rebind_workers() clears WORKER_REBIND, wakes up the idle workers and
then returns. If CPU hotplug cycle happens again before one of the
idle workers finishes the above wait_event(), rebind_workers() will
repeat the first part of the handshake - set WORKER_REBIND again and
wait for the idle worker to finish rebinding - and this leads to
deadlock because the idle worker would be waiting for WORKER_REBIND to
clear.
This is fixed by adding another interlocking step at the end -
rebind_workers() now waits for all the idle workers to finish the
above WORKER_REBIND wait before returning. This ensures that all
rebinding steps are complete on all idle workers before the next
hotplug cycle can happen.
This problem was diagnosed by Lai Jiangshan who also posted a patch to
fix the issue, upon which this patch is based.
This is the minimal fix and further patches are scheduled for the next
merge window to simplify the CPU hotplug path.
Signed-off-by: Tejun Heo <tj@kernel.org> Original-patch-by: Lai Jiangshan <laijs@cn.fujitsu.com>
LKML-Reference: <1346516916-1991-3-git-send-email-laijs@cn.fujitsu.com>
Ronny Hegewald [Fri, 31 Aug 2012 09:57:52 +0000 (09:57 +0000)]
xen: Use correct masking in xen_swiotlb_alloc_coherent.
When running 32-bit pvops-dom0 and a driver tries to allocate a coherent
DMA-memory the xen swiotlb-implementation returned memory beyond 4GB.
The underlaying reason is that if the supplied driver passes in a
DMA_BIT_MASK(64) ( hwdev->coherent_dma_mask is set to 0xffffffffffffffff)
our dma_mask will be u64 set to 0xffffffffffffffff even if we set it to
DMA_BIT_MASK(32) previously. Meaning we do not reset the upper bits.
By using the dma_alloc_coherent_mask function - it does the proper casting
and we get 0xfffffffff.
This caused not working sound on a system with 4 GB and a 64-bit
compatible sound-card with sets the DMA-mask to 64bit.
On bare-metal and the forward-ported xen-dom0 patches from OpenSuse a coherent
DMA-memory is always allocated inside the 32-bit address-range by calling
dma_alloc_coherent_mask.
This patch adds the same functionality to xen swiotlb and is a rebase of the
original patch from Ronny Hegewald which never got upstream b/c the
underlaying reason was not understood until now.
The original email with the original patch is in:
http://old-list-archives.xen.org/archives/html/xen-devel/2010-02/msg00038.html
the original thread from where the discussion started is in:
http://old-list-archives.xen.org/archives/html/xen-devel/2010-01/msg00928.html
Signed-off-by: Ronny Hegewald <ronny.hegewald@online.de> Signed-off-by: Stefano Panella <stefano.panella@citrix.com> Acked-By: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> CC: stable@vger.kernel.org
Alex Shi [Fri, 24 Aug 2012 08:55:13 +0000 (08:55 +0000)]
xen: fix logical error in tlb flushing
While TLB_FLUSH_ALL gets passed as 'end' argument to
flush_tlb_others(), the Xen code was made to check its 'start'
parameter. That may give a incorrect op.cmd to MMUEXT_INVLPG_MULTI
instead of MMUEXT_TLB_FLUSH_MULTI. Then it causes some page can not
be flushed from TLB.
This patch fixed this issue.
Reported-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Alex Shi <alex.shi@intel.com> Acked-by: Jan Beulich <jbeulich@suse.com> Tested-by: Yongjie Ren <yongjie.ren@intel.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* commit '4cb38750d49010ae72e718d46605ac9ba5a851b4': (6849 commits)
bcma: fix invalid PMU chip control masks
[libata] pata_cmd64x: whitespace cleanup
libata-acpi: fix up for acpi_pm_device_sleep_state API
sata_dwc_460ex: device tree may specify dma_channel
ahci, trivial: fixed coding style issues related to braces
ahci_platform: add hibernation callbacks
libata-eh.c: local functions should not be exposed globally
libata-transport.c: local functions should not be exposed globally
sata_dwc_460ex: support hardreset
ata: use module_pci_driver
drivers/ata/pata_pcmcia.c: adjust suspicious bit operation
pata_imx: Convert to clk_prepare_enable/clk_disable_unprepare
ahci: Enable SB600 64bit DMA on MSI K9AGM2 (MS-7327) v2
[libata] Prevent interface errors with Seagate FreeAgent GoFlex
drivers/acpi/glue: revert accidental license-related 6b66d95895c bits
libata-acpi: add missing inlines in libata.h
i2c-omap: Add support for I2C_M_STOP message flag
i2c: Fall back to emulated SMBus if the operation isn't supported natively
i2c: Add SCCB support
i2c-tiny-usb: Add support for the Robofuzz OSIF USB/I2C converter
...
Jan Kara [Wed, 5 Sep 2012 13:48:23 +0000 (15:48 +0200)]
udf: Fix data corruption for files in ICB
When a file is stored in ICB (inode), we overwrite part of the file, and
the page containing file's data is not in page cache, we end up corrupting
file's data by overwriting them with zeros. The problem is we use
simple_write_begin() which simply zeroes parts of the page which are not
written to. The problem has been introduced by be021ee4 (udf: convert to
new aops).
Fix the problem by providing a ->write_begin function which makes the page
properly uptodate.
CC: <stable@vger.kernel.org> # >= 2.6.24 Reported-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Jan Kara <jack@suse.cz>
xen/p2m: Fix one-off error in checking the P2M tree directory.
We would traverse the full P2M top directory (from 0->MAX_DOMAIN_PAGES
inclusive) when trying to figure out whether we can re-use some of the
P2M middle leafs.
Which meant that if the kernel was compiled with MAX_DOMAIN_PAGES=512
we would try to use the 512th entry. Fortunately for us the p2m_top_index
has a check for this:
powerpc: Don't use __put_user() in patch_instruction
patch_instruction() can be called very early on ppc32, when the kernel
isn't yet running at it's linked address. That can cause the !
is_kernel_addr() test in __put_user() to trip and call might_sleep()
which is very bad at that point during boot.
Use a lower level function instead for now, at least until we get to
rework ppc32 boot process to do the code patching later, like ppc64
does.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Paul Mackerras [Tue, 4 Sep 2012 18:33:08 +0000 (18:33 +0000)]
powerpc: Make sure IPI handlers see data written by IPI senders
We have been observing hangs, both of KVM guest vcpu tasks and more
generally, where a process that is woken doesn't properly wake up and
continue to run, but instead sticks in TASK_WAKING state. This
happens because the update of rq->wake_list in ttwu_queue_remote()
is not ordered with the update of ipi_message in
smp_muxed_ipi_message_pass(), and the reading of rq->wake_list in
scheduler_ipi() is not ordered with the reading of ipi_message in
smp_ipi_demux(). Thus it is possible for the IPI receiver not to see
the updated rq->wake_list and therefore conclude that there is nothing
for it to do.
In order to make sure that anything done before smp_send_reschedule()
is ordered before anything done in the resulting call to scheduler_ipi(),
this adds barriers in smp_muxed_message_pass() and smp_ipi_demux().
The barrier in smp_muxed_message_pass() is a full barrier to ensure that
there is a full ordering between the smp_send_reschedule() caller and
scheduler_ipi(). In smp_ipi_demux(), we use xchg() rather than
xchg_local() because xchg() includes release and acquire barriers.
Using xchg() rather than xchg_local() makes sense given that
ipi_message is not just accessed locally.
This moves the barrier between setting the message and calling the
cause_ipi() function into the individual cause_ipi implementations.
Most of them -- those that used outb, out_8 or similar -- already had
a full barrier because out_8 etc. include a sync before the MMIO
store. This adds an explicit barrier in the two remaining cases.
These changes made no measurable difference to the speed of IPIs as
measured using a simple ping-pong latency test across two CPUs on
different cores of a POWER7 machine.
The analysis of the reason why processes were not waking up properly
is due to Milton Miller.
Cc: stable@vger.kernel.org # v3.0+ Reported-by: Milton Miller <miltonm@bga.com> Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Mon, 3 Sep 2012 16:51:10 +0000 (16:51 +0000)]
powerpc: Restore correct DSCR in context switch
During a context switch we always restore the per thread DSCR value.
If we aren't doing explicit DSCR management
(ie thread.dscr_inherit == 0) and the default DSCR changed while
the process has been sleeping we end up with the wrong value.
Check thread.dscr_inherit and select the default DSCR or per thread
DSCR as required.
This was found with the following test case, when running with
more threads than CPUs (ie forcing context switching):
Anton Blanchard [Mon, 3 Sep 2012 16:49:47 +0000 (16:49 +0000)]
powerpc: Fix DSCR inheritance in copy_thread()
If the default DSCR is non zero we set thread.dscr_inherit in
copy_thread() meaning the new thread and all its children will ignore
future updates to the default DSCR. This is not intended and is
a change in behaviour that a number of our users have hit.
We just need to inherit thread.dscr and thread.dscr_inherit from
the parent which ends up being much simpler.
Anton Blanchard [Mon, 3 Sep 2012 16:48:46 +0000 (16:48 +0000)]
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
When we update the DSCR either via emulation of mtspr(DSCR) or via
a change to dscr_default in sysfs we don't update thread.dscr.
We will eventually update it at context switch time but there is
a period where thread.dscr is incorrect.
If we fork at this point we will copy the old value of thread.dscr
into the child. To avoid this, always keep thread.dscr in sync with
reality.
Anton Blanchard [Mon, 3 Sep 2012 16:47:56 +0000 (16:47 +0000)]
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
Writing to dscr_default in sysfs doesn't actually change the DSCR -
we rely on a context switch on each CPU to do the work. There is no
guarantee we will get a context switch in a reasonable amount of time
so fire off an IPI to force an immediate change.
This issue was found with the following test case:
Paul Mackerras [Thu, 26 Jul 2012 18:51:09 +0000 (18:51 +0000)]
powerpc/powernv: Always go into nap mode when CPU is offline
The CPU hotplug code for the powernv platform currently only puts
offline CPUs into nap mode if the powersave_nap variable is set.
However, HV-style KVM on this platform requires secondary CPU threads
to be offline and in nap mode. Since we know nap mode works just
fine on all POWER7 machines, and the only machines that support the
powernv platform are POWER7 machines, this changes the code to
always put offline CPUs into nap mode, regardless of powersave_nap.
Powersave_nap still controls whether or not CPUs go into nap mode
when idle, as before.
Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Paul Mackerras [Thu, 26 Jul 2012 13:56:11 +0000 (13:56 +0000)]
powerpc: Give hypervisor decrementer interrupts their own handler
At the moment the handler for hypervisor decrementer interrupts is
the same as for decrementer interrupts, i.e. timer_interrupt().
This is bogus; if we ever do get a hypervisor decrementer interrupt
it won't have anything to do with the next timer event. In fact
the only time we get hypervisor decrementer interrupts is when one
is left pending on exit from a KVM guest.
When we get a hypervisor decrementer interrupt we don't need to do
anything special to clear it, since they are edge-triggered on the
transition of HDEC from 0 to -1. Thus this adds an empty handler
function for them. We don't need to have them masked when interrupts
are soft-disabled, so we use STD_EXCEPTION_HV instead of
MASKABLE_EXCEPTION_HV.
Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Linus Walleij [Thu, 30 Aug 2012 17:22:36 +0000 (19:22 +0200)]
ARM: gemini: fix the gemini build
Test-compiling obscure machines I notice that the gemini (which
by the way lacks a defconfig) is broken since some time back.
Adding a simple missing include makes it build again.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
so the other CPU may temporarily see worker->flags which doesn't have
either WORKER_UNBOUND or WORKER_REBIND set and perform local wakeup
prematurely.
Fix it by using single explicit assignment via ACCESS_ONCE().
Because idle workers have another WORKER_NOT_RUNNING flag, this bug
doesn't exist for them; however, update it to use the same pattern for
consistency.
tj: Applied the change to idle workers too and updated comments and
patch description a bit.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: stable@vger.kernel.org
[ 2.086181] Waiting for root device /dev/mmcblk0p1...
[ 2.324066] Unhandled fault: imprecise external abort (0x406) at 0x00000000
[ 2.331451] Internal error: : 406 [#1] ARM
[ 2.335784] Modules linked in:
[ 2.339050] CPU: 0 Not tainted (3.6.0-rc3 #60)
[ 2.344146] PC is at default_idle+0x28/0x30
[ 2.348602] LR is at trace_hardirqs_on_caller+0x15c/0x1b0
...
This turned out to be due to memory corruption caused by long-broken
PIO code in drivers/mmc/host/omap.c. (Previously, this driver had
been using DMA; but the above commit caused the MMC driver to fall
back to PIO mode with an unmodified Kconfig.)
The PIO code, added with the rest of the driver in commit 730c9b7e6630f786fcec026fb11d2e6f2c90fdcb ("[MMC] Add OMAP MMC host
driver"), confused bytes with 16-bit words. This bug caused memory
located after the PIO transfer buffer to be corrupted with transfers
larger than 32 bytes. The driver also did not increment the buffer
pointer after the transfer occurred. This bug resulted in data
corruption during any transfer larger than 64 bytes.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Ian Chen [Wed, 29 Aug 2012 06:05:36 +0000 (15:05 +0900)]
mmc: card: Skip secure erase on MoviNAND; causes unrecoverable corruption.
For several MoviNAND eMMC parts, there are known issues with secure
erase and secure trim. For these specific MoviNAND devices, we skip
these operations.
Specifically, there is a bug in the eMMC firmware that causes
unrecoverable corruption when the MMC is erased with MMC_CAP_ERASE
enabled.
Doug Anderson [Wed, 25 Jul 2012 15:33:17 +0000 (08:33 -0700)]
mmc: dw_mmc: Disable low power mode if SDIO interrupts are used
The documentation for the dw_mmc part says that the low power
mode should normally only be set for MMC and SD memory and should
be turned off for SDIO cards that need interrupts detected.
The best place I could find to do this is when the SDIO interrupt
was first enabled. I rely on the fact that dw_mci_setup_bus()
will be called when it's time to reenable.
Signed-off-by: Doug Anderson <dianders@chromium.org> Acked-by: Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Seungwon Jeon [Wed, 1 Aug 2012 00:30:46 +0000 (09:30 +0900)]
mmc: dw_mmc: fix error handling in PIO mode
Data transfer will be continued until all the bytes are transmitted,
even if data crc error occurs during a multiple-block data transfer.
This means RXDR/TXDR interrupts will occurs until data transfer is
terminated. Early setting of host->sg to NULL prevents going into
xxx_data_pio functions, hence permanent unhandled RXDR/TXDR interrupts
occurs. And checking error interrupt status in the xxx_data_pio functions
is no need because dw_mci_interrupt does do the same. This patch also
removes it.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Seungwon Jeon [Wed, 1 Aug 2012 00:30:40 +0000 (09:30 +0900)]
mmc: dw_mmc: correct mishandling error interrupt
Datasheet of SYNOPSYS mentions that DTO(Data Transfer Over) interrupt
will be raised even if some error interrupts, however it is actually
found that DTO does not occur. SYNOPSYS has confirmed this issue.
Current implementation defers the call of tasklet_schedule until DTO
when the error interrupts is happened. This patch fixes error handling.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Seungwon Jeon [Wed, 1 Aug 2012 00:30:30 +0000 (09:30 +0900)]
mmc: dw_mmc: amend using error interrupt status
RINTSTS status includes masked interrupts as well as unmasked.
data_status and cmd_status are set by value of RINTSTS in interrupt handler
and tasklet finally uses it to decide whether error is happened or not.
In addition, MINTSTS status is used for setting data_status in PIO.
Masked error interrupt will not be handled and that status can be considered
non-error case.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed By: Girish K S <girish.shivananjappa@linaro.org> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
mmc: atmel-mci: not busy flag has also to be used for read operations
Even if the datasheet says that the not busy flag has to be used only
for write operations, it's false except for version lesser than v2xx.
Not waiting on the not busy flag for read operations can cause the
controller to hang-up during the initialization of some SD cards
with DMA after the first CMD6 -- the next command is sent too early.
Shawn Guo [Wed, 22 Aug 2012 15:10:01 +0000 (23:10 +0800)]
mmc: sdhci-esdhc: break out early if clock is 0
Since commit 30832ab56 ("mmc: sdhci: Always pass clock request value
zero to set_clock host op") was merged, esdhc_set_clock starts hitting
"if (clock == 0)" where ESDHC_SYSTEM_CONTROL has been operated. This
causes SDHCI card-detection function being broken. Fix the regression
by moving "if (clock == 0)" above ESDHC_SYSTEM_CONTROL operation.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Cc: <stable@vger.kernel.org> Signed-off-by: Chris Ball <cjb@laptop.org>
Jamie Iles [Thu, 30 Aug 2012 10:32:13 +0000 (11:32 +0100)]
KVM: PIC: fix use of uninitialised variable.
Commit aea218f3cbbc (KVM: PIC: call ack notifiers for irqs that are
dropped form irr) used an uninitialised variable to track whether an
appropriate apic had been found. This could result in calling the ack
notifier incorrectly.
Cc: Gleb Natapov <gleb@redhat.com> Cc: Avi Kivity <avi@redhat.com> Signed-off-by: Jamie Iles <jamie@jamieiles.com> Signed-off-by: Avi Kivity <avi@redhat.com>
UBI was mistakingly using 'kfree()' instead of 'kmem_cache_free()' when
freeing "attach eraseblock" structures in vtbl.c. Thankfully, this happened
only when we were doing auto-format, so many systems were unaffected. However,
there are still many users affected.
It is strange, but the system did not crash and nothing bad happened when
the SLUB memory allocator was used. However, in case of SLOB we observed an
crash right away.
This problem was introduced in 2.6.39 by commit
"6c1e875 UBI: add slab cache for ubi_scan_leb objects"
A note for stable trees:
Because variable were renamed, this won't cleanly apply to older kernels.
Changing names like this should help:
1. ai -> si
2. aeb_slab_cache -> seb_slab_cache
3. new_aeb -> new_seb
Reported-by: Richard Genoud <richard.genoud@gmail.com> Tested-by: Richard Genoud <richard.genoud@gmail.com> Tested-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Cc: stable@vger.kernel.org [v2.6.39+] Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Jan Kara [Mon, 3 Sep 2012 14:50:42 +0000 (16:50 +0200)]
ext3: Fix fdatasync() for files with only i_size changes
Code tracking when transaction needs to be committed on fdatasync(2) forgets
to handle a situation when only inode's i_size is changed. Thus in such
situations fdatasync(2) doesn't force transaction with new i_size to disk
and that can result in wrong i_size after a crash.
Fix the issue by updating inode's i_datasync_tid whenever its size is
updated.
CC: <stable@vger.kernel.org> # >= 2.6.32 Reported-by: Kristian Nielsen <knielsen@knielsen-hq.org> Signed-off-by: Jan Kara <jack@suse.cz>
projects / mirror_ubuntu-kernels.git / log