Hugh Dickins [Fri, 10 Nov 2006 21:32:40 +0000 (21:32 +0000)]
[POWERPC] Make soft_enabled irqs preempt safe
Rewrite local_get_flags and local_irq_disable to use r13 explicitly,
to avoid the risk that gcc will split get_paca()->soft_enabled into a
sequence unsafe against preemption. Similar care in local_irq_restore.
Signed-off-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
The recent IO accessor changes broke IDE on arch/ppc due to the IDE
stream IO macros using the new reads/writes{b,w,l} accessors that
are only defined for arch/powerpc. This adds them to arch/ppc.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
The new IO accessor code allows to stick a token in the top bit of MMIO
addresses which gets masked out during actual accesses. However, the
__raw_* accessors forgot to mask it out. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
In order to suppose platforms with devices above 4Gb on 32 bits platforms
with a >32 bits physical address space, we used to have a special ioremap64
along with a fixup routine fixup_bigphys_addr.
This shouldn't be necessary anymore as struct resource now supports 64 bits
addresses even on 32 bits archs. This patch enables that option when
CONFIG_PHYS_64BIT is set and removes ioremap64 and fixup_bigphys_addr.
This is a preliminary work for the upcoming merge of 32 and 64 bits io.h
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Jeremy Kerr [Sat, 11 Nov 2006 06:25:18 +0000 (17:25 +1100)]
[POWERPC] Cell iommu support
This patch adds full cell iommu support (and iommu disabled mode).
It implements mapping/unmapping of iommu pages on demand using the
standard powerpc iommu framework. It also supports running with
iommu disabled for machines with less than 2GB of memory. (The
default is off in that case, though it can be forced on with the
kernel command line option iommu=force).
Signed-off-by: Jeremy Kerr <jk@ozlabs.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] Make direct DMA use node local allocations
This patch makes dma_alloc_coherent() use node local allocation when
using the direct DMA ops. The node is obtained from the new device
extension. If no such extension is present, the current node is used.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] Add an optional offset to direct DMA on 64 bits
This patch adds an optional global offset that can be added to DMA addresses
when using the direct DMA operations.
That brings it a step closer to the 32 bits direct DMA operations, and makes
it useable on Cell when the MMU is disabled and we are using a spider
southbridge.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
We use the powerpc specific low level MMIO accessor variants instead
of readl() or readl_be() because we know spidernet is not a real PCI
device and we can thus avoid the performance hit caused by the PCI
workarounds.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch implements a workaround for a Spider PCI host bridge bug
where it doesn't enforce some of the PCI ordering rules unless some
manual manipulation of a special register is done. In order to be
fully compliant with the PCI spec, I do this on every MMIO read
operation.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] Allow hooking of PCI MMIO & PIO accessors on 64 bits
This patch reworks the way iSeries hooks on PCI IO operations (both MMIO
and PIO) and provides a generic way for other platforms to do so (we
have need to do that for various other platforms).
While reworking the IO ops, I ended up doing some spring cleaning in
io.h and eeh.h which I might want to split into 2 or 3 patches (among
others, eeh.h had a lot of useless stuff in it).
A side effect is that EEH for PIO should work now (it used to pass IO
ports down to the eeh address check functions which is bogus).
Also, new are MMIO "repeat" ops, which other archs like ARM already had,
and that we have too now: readsb, readsw, readsl, writesb, writesw,
writesl.
In the long run, I might also make EEH use the hooks instead
of wrapping at the toplevel, which would make things even cleaner and
relegate EEH completely in platforms/iseries, but we have to measure the
performance impact there (though it's really only on MMIO reads)
Since I also need to hook on ioremap, I shuffled the functions a bit
there. I introduced ioremap_flags() to use by drivers who want to pass
explicit flags to ioremap (and it can be hooked). The old __ioremap() is
still there as a low level and cannot be hooked, thus drivers who use it
should migrate unless they know they want the low level version.
The patch "arch provides generic iomap missing accessors" (should be
number 4 in this series) is a pre-requisite to provide full iomap
API support with this patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] Cell fixup DMA offset for new southbridge
This patch makes the Cell DMA code work on both the Spider and the Axon
south bridges by turning cell_dma_valid into a variable instead of a
constant. This is a temporary patch until we have full iommu support.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] Generic OF platform driver for PCI host bridges.
When enabled in Kconfig, it will pick up any of_platform_device
matching it's match list (currently type "pci", "pcix", "pcie",
or "ht" and setup a PHB for it.
Platform must provide a ppc_md.pci_setup_phb() for it to work
(for doing the necessary initialisations specific to a given PHB
like setting up the config space ops).
It's currently only available on 64 bits as the 32 bits PCI code
can't quite cope with it in it's current form. I will fix that
later.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] Resolve the BUID for RTAS PCI config space accesses
The BUID is the first entry of a PCI host bridge "reg" property.
Now that PCI busses can be anywhere in the device-tree, we need to
fully translate the value there to a CPU physical address before
we can use it with RTAS.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] Resolve the parent address of a PCI bus range
When parsing the OF "ranges" properties of PCI host busses to determine
the mapping of a PCI bus, we need to translate the "parent" address using
the prom_parse.c routines in order to obtain a CPU physical address.
This wasn't necessary while PCI busses were always at the root of the
device-tree but this is no longer the case on Cell where they can be
anywhere in the tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] Add DMA ops support for of_platform_device to Cell
This patch adds a bus device notifier to the of_platform bus type on
cell to setup the DMA operations for of_platform_devices. We currently
use the PCI operations as Cell use a special version of them that
happens to be suitable for our needs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch completely refactors DMA operations for 64 bits powerpc. 32 bits
is untouched for now.
We use the new dev_archdata structure to add the dma operations pointer
and associated data to struct device. While at it, we also add the OF node
pointer and numa node. In the future, we might want to look into merging
that with pci_dn as well.
The old vio, pci-iommu and pci-direct DMA ops are gone. They are now replaced
by a set of generic iommu and direct DMA ops (non PCI specific) that can be
used by bus types. The toplevel implementation is now inline.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove the now unused "liobn" field in ibmveth which also avoids
having insider knowledge of the iommu table in that driver.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Santiago Leon <santil@us.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Hook up of_platform_bus_probe with the cell platform in order to publish
the non-PCI devices in the device-tree of cell blades as of_platform_device(s)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch first splits of_device.c and of_platform.c, the later containing
the bits relative to of_platform_device's. On the "breaks" side of things,
drivers uisng of_platform_device(s) need to include asm/of_platform.h now
and of_(un)register_driver is now of_(un)register_platform_driver.
In addition to a few utility functions to locate of_platform_device(s),
the main new addition is of_platform_bus_probe() which allows the platform
code to trigger an automatic creation of of_platform_devices for a whole
tree of devices.
The function acts based on the type of the various "parent" devices encountered
from a provided root, using either a default known list of bus types that can be
"probed" or a passed-in list. It will only register devices on busses matching
that list, which mean that typically, it will not register PCI devices, as
expected (since they will be picked up by the PCI layer).
This will be used by Cell platforms using 4xx-type IOs in the Axon bridge
and can be used by any embedded-type device as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] Improve MPIC driver auto-configuration from DT
This patch applies on top of the MPIC DCR support. It makes the MPIC
driver capable of a lot more auto-configuration based on the device-tree,
for example, it can retreive it's own physical address if not passed as
an argument, find out if it's DCR or MMIO mapped, and set the BIG_ENDIAN
flag automatically in the presence of a "big-endian" property in the
device-tree node.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch implements support for DCR based MPIC implementations. Such
implementations have the MPIC_USES_DCR flag set and don't use the phys_addr
argument of mpic_alloc (they require a valid dcr mapping in the device node)
This version of the patch can use a little bif of cleanup still (I can
probably consolidate rb->dbase/doff, at least once I'm sure on how the
hardware is actually supposed to work vs. possible simulator issues) and
it should be possible to build a DCR-only version of the driver. I need
to cleanup a bit the CONFIG_* handling for that and probably introduce
CONFIG_MPIC_MMIO and CONFIG_MPIC_DCR.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] Make EMAC use generic DCR access methods
This patch makes the EMAC driver use the new DCR access methods. It
doesn't yet uses dcr_map() and thus still only work with real DCRs.
This will be fixed in a later patch
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds new dcr_map/dcr_read/dcr_write accessors for DCRs that
can be used by drivers to transparently address either native DCRs or
memory mapped DCRs. The implementation for memory mapped DCRs is done
after the binding being currently worked on for SLOF and the Axon
chipset. This patch enables it for the cell native platform
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] Remove ppc_md.pci_map_irq & ppc_swizzle for ARCH=powerpc
These were inherited from ARCH=ppc, but are not needed since parsing of interrupts
should be done via the of_* functions (who can do swizzling). If we ever need to
do non-standard swizzling on bridges without a device-node, then we might add
back a slightly different version of ppc_md.pci_swizzle but for now, that is not
the case.
I removed the couple of calls for these in 83xx. If that breaks something, then
there is a problem with the device-tree on these.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch reworks the way IRQs are fixed up on PCI for arch powerpc.
It makes pci_read_irq_line() called by default in the PCI code for
devices that are probed, and add an optional per-device fixup in
ppc_md for platforms that really need to correct what they obtain
from pci_read_irq_line().
It also removes ppc_md.irq_bus_setup which was only used by pSeries
and should not be needed anymore.
I've also removed the pSeries s7a workaround as it can't work with
the current interrupt code anyway. I'm trying to get one of these
machines working so I can test a proper fix for that problem.
I also haven't updated the old-style fixup code from 85xx_cds.c
because it's actually buggy :) It assigns pci_dev->irq hard coded
numbers which is no good with the new IRQ mapping code. It should
at least use irq_create_mapping(NULL, hard_coded_number); and possibly
also set_irq_type() to set them as level low.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
[XFRM]: Fix aevent structuring to be more complete.
aevents can not uniquely identify an SA. We break the ABI with this
patch, but consensus is that since it is not yet utilized by any
(known) application then it is fine (better do it now than later).
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Sun, 3 Dec 2006 06:11:01 +0000 (22:11 -0800)]
[NETFILTER]: Mark old IPv4-only connection tracking scheduled for removal
Also remove the references to "new connection tracking" from Kconfig.
After some short stabilization period of the new connection tracking
helpers/NAT code the old one will be removed.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Sun, 3 Dec 2006 06:08:01 +0000 (22:08 -0800)]
[NETFILTER]: nf_conntrack: add helper function for expectation initialization
Expectation address masks need to be differently initialized depending
on the address family, create helper function to avoid cluttering up
the code too much.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Split out from Jozsef's big nf_nat patch with a few small fixes by myself.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Add NAT support for nf_conntrack. Joint work of Jozsef Kadlecsik,
Yasuyuki Kozakai, Martin Josefsson and myself.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Sun, 3 Dec 2006 06:05:46 +0000 (22:05 -0800)]
[NETFILTER]: Kconfig: improve conntrack selection
Improve the connection tracking selection (well, the user experience,
not really the aesthetics) by offering one option to enable connection
tracking and a choice between the implementations.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Sun, 3 Dec 2006 06:05:25 +0000 (22:05 -0800)]
[NETFILTER]: nf_conntrack: automatic helper assignment for expectations
Some helpers (namely H.323) manually assign further helpers to expected
connections. This is not possible with nf_conntrack anymore since we
need to know whether a helper is used at allocation time.
Handle the helper assignment centrally, which allows to perform the
correct allocation and as a nice side effect eliminates the need
for the H.323 helper to fiddle with nf_conntrack_lock.
Mid term the allocation scheme really needs to be redesigned since
we do both the helper and expectation lookup _twice_ for every new
connection.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Adding the alignment to the size doesn't make any sense, what it
should do is align the size of the conntrack structure to the
alignment requirements of the helper structure and return an
aligned pointer in nfct_help().
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Sun, 3 Dec 2006 06:04:04 +0000 (22:04 -0800)]
[NET]: Accept wildcard delimiters in in[46]_pton
Accept -1 as delimiter to abort parsing without an error at the first
unknown character. This is needed by the upcoming nf_conntrack SIP
helper, where addresses are delimited by either '\r' or '\n' characters.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Sat, 2 Dec 2006 04:10:13 +0000 (20:10 -0800)]
[NETFILTER]: Kill ip_queue from feature removal schedule.
We really can't remove ip_queue. Many users use this, there is no binary
compatible interface and even the compat replacement for the originally
statically linked library doesn't work. There is also no real necessity
to remove the code, so the feature-removal-schedule entry should be
removed instead.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Fri, 1 Dec 2006 03:54:05 +0000 (19:54 -0800)]
[NET_SCHED]: policer: restore compatibility with old iproute binaries
The tc actions increased the size of struct tc_police, which broke
compatibility with old iproute binaries since both the act_police
and the old NET_CLS_POLICE code check for an exact size match.
Since the new members are not even used, the simple fix is to also
accept the size of the old structure. Dumping is not affected since
old userspace will receive a bigger structure, which is handled fine.
Signed-off-by: Patrick McHardy <kaber@trash.net> Acked-by: Jamal Hadi Salim <hadi@cyberus.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro [Fri, 1 Dec 2006 03:26:35 +0000 (19:26 -0800)]
[EBTABLES]: Move more stuff into ebt_verify_pointers().
Take intialization of ->hook_entry[...], ->entries_size and ->nentries
over there, pull the check for empty chains into the end of that sucker.
Now it's self-contained, so we can move it up in the very beginning of
translate_table() *and* we can rely on ->hook_entry[] being properly
transliterated after it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro [Fri, 1 Dec 2006 03:25:51 +0000 (19:25 -0800)]
[EBTABLES]: Split ebt_check_entry_size_and_hooks
Split ebt_check_entry_size_and_hooks() in two parts - one that does
sanity checks on pointers (basically, checks that we can safely
use iterator from now on) and the rest of it (looking into details
of entry).
The loop applying ebt_check_entry_size_and_hooks() is split in two.
Populating newinfo->hook_entry[] is done in the first part.
Unused arguments killed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro [Fri, 1 Dec 2006 03:24:49 +0000 (19:24 -0800)]
[EBTABLES]: Deal with the worst-case behaviour in loop checks.
No need to revisit a chain we'd already finished with during
the check for current hook. It's either instant loop (which
we'd just detected) or a duplicate work.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Adrian Bunk [Fri, 1 Dec 2006 01:22:29 +0000 (17:22 -0800)]
[NET]: Possible cleanups.
This patch contains the following possible cleanups:
- make the following needlessly global functions statis:
- ipv4/tcp.c: __tcp_alloc_md5sig_pool()
- ipv4/tcp_ipv4.c: tcp_v4_reqsk_md5_lookup()
- ipv4/udplite.c: udplite_rcv()
- ipv4/udplite.c: udplite_err()
- make the following needlessly global structs static:
- ipv4/tcp_ipv4.c: tcp_request_sock_ipv4_ops
- ipv4/tcp_ipv4.c: tcp_sock_ipv4_specific
- ipv6/tcp_ipv6.c: tcp_request_sock_ipv6_ops
- net/ipv{4,6}/udplite.c: remove inline's from static functions
(gcc should know best when to inline them)
Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Miika Komu [Fri, 1 Dec 2006 00:40:51 +0000 (16:40 -0800)]
[IPSEC]: Add netlink interface for the encapsulation family.
Signed-off-by: Miika Komu <miika@iki.fi> Signed-off-by: Diego Beltrami <Diego.Beltrami@hiit.fi> Signed-off-by: Kazunori Miyazawa <miyazawa@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Miika Komu [Fri, 1 Dec 2006 00:40:43 +0000 (16:40 -0800)]
[IPSEC]: Add encapsulation family.
Signed-off-by: Miika Komu <miika@iki.fi> Signed-off-by: Diego Beltrami <Diego.Beltrami@hiit.fi> Signed-off-by: Kazunori Miyazawa <miyazawa@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
When peeking at the next packet in a child qdisc by calling dequeue/requeue,
the upper qdisc qlen counter may get out of sync in case the requeue fails.
The qdisc and the child qdisc both have their counter decremented, but since
no packet is given to the upper qdisc it won't decrement its counter itself.
requeue should not fail, so this is mostly for "correctness".
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Thu, 30 Nov 2006 01:36:43 +0000 (17:36 -0800)]
[NET_SCHED]: Fix endless loops (part 3): HFSC
Convert HFSC to use qdisc_tree_decrease_len() and add a callback
for deactivating a class when its child queue becomes empty.
All queue purging goes through hfsc_purge_queue(), which is used in
three cases: grafting, class creation (when a leaf class is turned
into an intermediate class by attaching a new class) and class
deletion. In all cases qdisc_tree_decrease_len() is needed.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
There are multiple problems related to qlen adjustment that can lead
to an upper qdisc getting out of sync with the real number of packets
queued, leading to endless dequeueing attempts by the upper layer code.
All qdiscs must maintain an accurate q.qlen counter. There are basically
two groups of operations affecting the qlen: operations that propagate
down the tree (enqueue, dequeue, requeue, drop, reset) beginning at the
root qdisc and operations only affecting a subtree or single qdisc
(change, graft, delete class). Since qlen changes during operations from
the second group don't propagate to ancestor qdiscs, their qlen values
become desynchronized.
This patch adds a function to propagate qlen changes up the qdisc tree,
optionally calling a callback function to perform qdisc-internal
maintenance when the child qdisc becomes empty. The follow-up patches
will convert all qdiscs to use this function where necessary.
Noticed by Timo Steinbach <tsteinbach@astaro.com>.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Thu, 30 Nov 2006 01:34:50 +0000 (17:34 -0800)]
[NET_SCHED]: sch_htb: perform qlen adjustment immediately in ->delete
qlen adjustment should happen immediately in ->delete and not in the
class destroy function because the reference count will not hit zero in
->delete (sch_api holds a reference) but in ->put. Since the qdisc
lock is released between deletion of the class and final destruction
this creates an externally visible error in the qlen counter.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
James Morris [Wed, 29 Nov 2006 21:50:27 +0000 (16:50 -0500)]
Rename class_destroy to avoid namespace conflicts.
We're seeing increasing namespace conflicts between the global
class_destroy() function declared in linux/device.h, and the private
function in the SELinux core code. This patch renames the SELinux
function to cls_destroy() to avoid this conflict.
Acked-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: James Morris <jmorris@namei.org>
Paul Moore [Wed, 29 Nov 2006 18:18:20 +0000 (13:18 -0500)]
NetLabel: add the ranged tag to the CIPSOv4 protocol
Add support for the ranged tag (tag type #5) to the CIPSOv4 protocol.
The ranged tag allows for seven, or eight if zero is the lowest category,
category ranges to be specified in a CIPSO option. Each range is specified by
two unsigned 16 bit fields, each with a maximum value of 65534. The two values
specify the start and end of the category range; if the start of the category
range is zero then it is omitted.
See Documentation/netlabel/draft-ietf-cipso-ipsecurity-01.txt for more details.
Signed-off-by: Paul Moore <paul.moore@hp.com> Signed-off-by: James Morris <jmorris@namei.org>
Paul Moore [Wed, 29 Nov 2006 18:18:19 +0000 (13:18 -0500)]
NetLabel: add the enumerated tag to the CIPSOv4 protocol
Add support for the enumerated tag (tag type #2) to the CIPSOv4 protocol.
The enumerated tag allows for 15 categories to be specified in a CIPSO option,
where each category is an unsigned 16 bit field with a maximum value of 65534.
See Documentation/netlabel/draft-ietf-cipso-ipsecurity-01.txt for more details.
Signed-off-by: Paul Moore <paul.moore@hp.com> Signed-off-by: James Morris <jmorris@namei.org>
Paul Moore [Wed, 29 Nov 2006 18:18:18 +0000 (13:18 -0500)]
NetLabel: convert to an extensibile/sparse category bitmap
The original NetLabel category bitmap was a straight char bitmap which worked
fine for the initial release as it only supported 240 bits due to limitations
in the CIPSO restricted bitmap tag (tag type 0x01). This patch converts that
straight char bitmap into an extensibile/sparse bitmap in order to lay the
foundation for other CIPSO tag types and protocols.
This patch also has a nice side effect in that all of the security attributes
passed by NetLabel into the LSM are now in a format which is in the host's
native byte/bit ordering which makes the LSM specific code much simpler; look
at the changes in security/selinux/ss/ebitmap.c as an example.
Signed-off-by: Paul Moore <paul.moore@hp.com> Signed-off-by: James Morris <jmorris@namei.org>
projects / mirror_ubuntu-kernels.git / log