Jens Axboe [Fri, 6 Mar 2015 19:56:13 +0000 (12:56 -0700)]
NVMe: increase depth of admin queue
Usually the admin queue depth of 64 is plenty, but for some use cases we
really need it larger. Examples are use cases like MAT, where you have
to touch all of NAND for init/format like purposes. In those cases, we
see a good 2x increase with an increased queue depth.
Signed-off-by: Jens Axboe <axboe@fb.com> Acked-by: Keith Busch <keith.busch@intel.com>
Murali Iyer [Thu, 26 Mar 2015 16:07:51 +0000 (11:07 -0500)]
nvme: Fix PRP list calculation for non-4k system page size
PRP list calculation is supposed to be based on device's page size.
Systems with page size larger than device's page size cause corruption
to the name space as well as system memory with out this fix.
Systems like x86 might not experience this issue because it uses
PAGE_SIZE of 4K where as powerpc uses PAGE_SIZE of 64k while NVMe device's
page size varies depending upon the vendor.
Signed-off-by: Murali Iyer <mniyer@us.ibm.com> Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Keith Busch [Tue, 31 Mar 2015 16:37:17 +0000 (10:37 -0600)]
NVMe: Fix blk-mq hot cpu notification
The driver may issue commands to a device that may never return, so its
request_queue could always have active requests while the controller is
running. Waiting for the queue to freeze could block forever, which is
what blk-mq's hot cpu notification handler was doing when nvme drives
were in use.
This has the nvme driver make the asynchronous event command's tag
reserved and does not keep the request active. We can't have more than
one since the request is released back to the request_queue before the
command is completed. Having only one avoids potential tag collisions,
and reserving the tag for this purpose prevents other admin tasks from
reusing the tag.
I also couldn't think of a scenario where issuing AEN requests single
depth is worse than issuing them in batches, so I don't think we lose
anything with this change.
As an added bonus, doing it this way removes "Cancelling I/O" warnings
observed when unbinding the nvme driver from a device.
Keith Busch [Thu, 26 Mar 2015 19:49:33 +0000 (13:49 -0600)]
NVMe: Freeze admin queue on device failure
This fixes a race accessing an invalid address when a controller's admin
queue is in use during a reset for failure or hot removal occurs. The
admin queue will be frozen to prevent new users from entering prior to
the doorbell queue being unmapped.
Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Ross Zwisler [Tue, 17 Mar 2015 18:56:30 +0000 (12:56 -0600)]
brd: update maintainer to be Jens Axboe
Nick Piggin is currently listed as the maintainer of BRD in MAINTAINERS,
but the mails sent to the listed address are returned as undeliverable.
Update the maintainer for BRD to be Jens Axboe, since patches for BRD
flow up through him.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Mike Snitzer [Fri, 13 Mar 2015 03:56:02 +0000 (23:56 -0400)]
blk-mq: add blk_mq_init_allocated_queue and export blk_mq_register_disk
Add a variant of blk_mq_init_queue that allows a previously allocated
queue to be initialized. blk_mq_init_allocated_queue models
blk_init_allocated_queue -- which was also created for DM's use.
DM's approach to device creation requires a placeholder request_queue be
allocated for use with alloc_dev() but the decision about what type of
request_queue will be ultimately created is deferred until all component
devices referenced in the DM table are processed to determine the table
type (request-based, blk-mq request-based, or bio-based).
Also, because of DM's late finalization of the request_queue type
the call to blk_mq_register_disk() doesn't happen during alloc_dev().
Must export blk_mq_register_disk() so that DM can backfill the 'mq' dir
once the blk-mq queue is fully allocated.
Signed-off-by: Mike Snitzer <snitzer@redhat.com> Reviewed-by: Ming Lei <ming.lei@canonical.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Mike Snitzer [Fri, 13 Mar 2015 03:53:26 +0000 (23:53 -0400)]
blk-mq: fix use of incorrect goto label in blk_mq_init_queue error path
If percpu_ref_init() fails the allocated q and hctxs must get cleaned
up; using 'err_map' doesn't allow that to happen.
Signed-off-by: Mike Snitzer <snitzer@redhat.com> Reviewed-by: Ming Lei <ming.lei@canonical.com> Cc: stable@kernel.org Signed-off-by: Jens Axboe <axboe@fb.com>
Linus Torvalds [Fri, 13 Mar 2015 01:46:19 +0000 (18:46 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"13 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
memcg: disable hierarchy support if bound to the legacy cgroup hierarchy
mm: reorder can_do_mlock to fix audit denial
kasan, module: move MODULE_ALIGN macro into <linux/moduleloader.h>
kasan, module, vmalloc: rework shadow allocation for modules
fanotify: fix event filtering with FAN_ONDIR set
mm/nommu.c: export symbol max_mapnr
arch/c6x/include/asm/pgtable.h: define dummy pgprot_writecombine for !MMU
nilfs2: fix deadlock of segment constructor during recovery
mm: cma: fix CMA aligned offset calculation
mm, hugetlb: close race when setting PageTail for gigantic pages
mm, oom: do not fail __GFP_NOFAIL allocation if oom killer is disabled
drivers/rtc/rtc-s3c.c: add .needs_src_clk to s3c6410 RTC data
ocfs2: make append_dio an incompat feature
Vladimir Davydov [Thu, 12 Mar 2015 23:26:19 +0000 (16:26 -0700)]
memcg: disable hierarchy support if bound to the legacy cgroup hierarchy
If the memory cgroup controller is initially mounted in the scope of the
default cgroup hierarchy and then remounted to a legacy hierarchy, it will
still have hierarchy support enabled, which is incorrect. We should
disable hierarchy support if bound to the legacy cgroup hierarchy.
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com> Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Michal Hocko <mhocko@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A userspace call to mmap(MAP_LOCKED) may result in the successful locking
of memory while also producing a confusing audit log denial. can_do_mlock
checks capable and rlimit. If either of these return positive
can_do_mlock returns true. The capable check leads to an LSM hook used by
apparmour and selinux which produce the audit denial. Reordering so
rlimit is checked first eliminates the denial on success, only recording a
denial when the lock is unsuccessful as a result of the denial.
Signed-off-by: Jeff Vander Stoep <jeffv@google.com> Acked-by: Nick Kralevich <nnk@google.com> Cc: Jeff Vander Stoep <jeffv@google.com> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: Rik van Riel <riel@redhat.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Paul Cassella <cassella@cray.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Ryabinin [Thu, 12 Mar 2015 23:26:14 +0000 (16:26 -0700)]
kasan, module: move MODULE_ALIGN macro into <linux/moduleloader.h>
include/linux/moduleloader.h is more suitable place for this macro.
Also change alignment to PAGE_SIZE for CONFIG_KASAN=n as such
alignment already assumed in several places.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com> Cc: Dmitry Vyukov <dvyukov@google.com> Acked-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Ryabinin [Thu, 12 Mar 2015 23:26:11 +0000 (16:26 -0700)]
kasan, module, vmalloc: rework shadow allocation for modules
Current approach in handling shadow memory for modules is broken.
Shadow memory could be freed only after memory shadow corresponds it is no
longer used. vfree() called from interrupt context could use memory its
freeing to store 'struct llist_node' in it:
void vfree(const void *addr)
{
...
if (unlikely(in_interrupt())) {
struct vfree_deferred *p = this_cpu_ptr(&vfree_deferred);
if (llist_add((struct llist_node *)addr, &p->list))
schedule_work(&p->wq);
Later this list node used in free_work() which actually frees memory.
Currently module_memfree() called in interrupt context will free shadow
before freeing module's memory which could provoke kernel crash.
So shadow memory should be freed after module's memory. However, such
deallocation order could race with kasan_module_alloc() in module_alloc().
Free shadow right before releasing vm area. At this point vfree()'d
memory is not used anymore and yet not available for other allocations.
New VM_KASAN flag used to indicate that vm area has dynamically allocated
shadow memory so kasan frees shadow only if it was previously allocated.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com> Acked-by: Rusty Russell <rusty@rustcorp.com.au> Cc: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With FAN_ONDIR set, the user can end up getting events, which it hasn't
marked. This was revealed with fanotify04 testcase failure on
Linux-4.0-rc1, and is a regression from 3.19, revealed with 66ba93c0d7fe6
("fanotify: don't set FAN_ONDIR implicitly on a marks ignored mask").
# /opt/ltp/testcases/bin/fanotify04
[ ... ]
fanotify04 7 TPASS : event generated properly for type 100000
fanotify04 8 TFAIL : fanotify04.c:147: got unexpected event 30
fanotify04 9 TPASS : No event as expected
The testcase sets the adds the following marks : FAN_OPEN | FAN_ONDIR for
a fanotify on a dir. Then does an open(), followed by close() of the
directory and expects to see an event FAN_OPEN(0x20). However, the
fanotify returns (FAN_OPEN|FAN_CLOSE_NOWRITE(0x10)). This happens due to
the flaw in the check for event_mask in fanotify_should_send_event() which
does:
if (event_mask & marks_mask & ~marks_ignored_mask)
return true;
Fix this by masking the outgoing events to the user, as we already take
care of FAN_ONDIR and FAN_EVENT_ON_CHILD.
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com> Tested-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Eric Paris <eparis@redhat.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chen Gang [Thu, 12 Mar 2015 23:26:03 +0000 (16:26 -0700)]
arch/c6x/include/asm/pgtable.h: define dummy pgprot_writecombine for !MMU
When !MMU, asm-generic will not define default pgprot_writecombine, so c6x
needs to define it by itself. The related error:
CC [M] fs/pstore/ram_core.o
fs/pstore/ram_core.c: In function 'persistent_ram_vmap':
fs/pstore/ram_core.c:399:10: error: implicit declaration of function 'pgprot_writecombine' [-Werror=implicit-function-declaration]
prot = pgprot_writecombine(PAGE_KERNEL);
^
fs/pstore/ram_core.c:399:8: error: incompatible types when assigning to type 'pgprot_t {aka struct <anonymous>}' from type 'int'
prot = pgprot_writecombine(PAGE_KERNEL);
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com> Cc: Mark Salter <msalter@redhat.com> Cc: Aurelien Jacquiot <a-jacquiot@ti.com> Cc: "Kirill A. Shutemov" <kirill@shutemov.name> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ryusuke Konishi [Thu, 12 Mar 2015 23:26:00 +0000 (16:26 -0700)]
nilfs2: fix deadlock of segment constructor during recovery
According to a report from Yuxuan Shui, nilfs2 in kernel 3.19 got stuck
during recovery at mount time. The code path that caused the deadlock was
as follows:
nilfs_fill_super()
load_nilfs()
nilfs_salvage_orphan_logs()
* Do roll-forwarding, attach segment constructor for recovery,
and kick it.
nilfs_segctor_thread()
nilfs_segctor_thread_construct()
* A lock is held with nilfs_transaction_lock()
nilfs_segctor_do_construct()
nilfs_segctor_drop_written_files()
iput()
iput_final()
write_inode_now()
writeback_single_inode()
__writeback_single_inode()
do_writepages()
nilfs_writepage()
nilfs_construct_dsync_segment()
nilfs_transaction_lock() --> deadlock
This can happen if commit 7ef3ff2fea8b ("nilfs2: fix deadlock of segment
constructor over I_SYNC flag") is applied and roll-forward recovery was
performed at mount time. The roll-forward recovery can happen if datasync
write is done and the file system crashes immediately after that. For
instance, we can reproduce the issue with the following steps:
< nilfs2 is mounted on /nilfs (device: /dev/sdb1) >
# dd if=/dev/zero of=/nilfs/test bs=4k count=1 && sync
# dd if=/dev/zero of=/nilfs/test conv=notrunc oflag=dsync bs=4k
count=1 && reboot -nfh
< the system will immediately reboot >
# mount -t nilfs2 /dev/sdb1 /nilfs
The deadlock occurs because iput() can run segment constructor through
writeback_single_inode() if MS_ACTIVE flag is not set on sb->s_flags. The
above commit changed segment constructor so that it calls iput()
asynchronously for inodes with i_nlink == 0, but that change was
imperfect.
This fixes the another deadlock by deferring iput() in segment constructor
even for the case that mount is not finished, that is, for the case that
MS_ACTIVE flag is not set.
Danesh Petigara [Thu, 12 Mar 2015 23:25:57 +0000 (16:25 -0700)]
mm: cma: fix CMA aligned offset calculation
The CMA aligned offset calculation is incorrect for non-zero order_per_bit
values.
For example, if cma->order_per_bit=1, cma->base_pfn= 0x2f800000 and
align_order=12, the function returns a value of 0x17c00 instead of 0x400.
This patch fixes the CMA aligned offset calculation.
The previous calculation was wrong and would return too-large values for
the offset, so that when cma_alloc looks for free pages in the bitmap with
the requested alignment > order_per_bit, it starts too far into the bitmap
and so CMA allocations will fail despite there actually being plenty of
free pages remaining. It will also probably have the wrong alignment.
With this change, we will get the correct offset into the bitmap.
One affected user is powerpc KVM, which has kvm_cma->order_per_bit set to
KVM_CMA_CHUNK_ORDER - PAGE_SHIFT, or 18 - 12 = 6.
Michal Hocko [Thu, 12 Mar 2015 23:25:52 +0000 (16:25 -0700)]
mm, oom: do not fail __GFP_NOFAIL allocation if oom killer is disabled
Tetsuo Handa has pointed out that __GFP_NOFAIL allocations might fail
after OOM killer is disabled if the allocation is performed by a kernel
thread. This behavior was introduced from the very beginning by 7f33d49a2ed5 ("mm, PM/Freezer: Disable OOM killer when tasks are frozen").
This means that the basic contract for the allocation request is broken
and the context requesting such an allocation might blow up unexpectedly.
There are basically two ways forward.
1) move oom_killer_disable after kernel threads are frozen. This has a
risk that the OOM victim wouldn't be able to finish because it would
depend on an already frozen kernel thread. This would be really tricky
to debug.
2) do not fail GFP_NOFAIL allocation no matter what and risk a
potential Freezable kernel threads will loop and fail the suspend.
Incidental allocations after kernel threads are frozen will at least
dump a warning - if we are lucky and the serial console is still active
of course...
This patch implements the later option because it is safer. We would see
warning rather than allocation failures for the kernel threads which would
blow up otherwise and have a higher chances to identify __GFP_NOFAIL users
from deeper pm code.
Signed-off-by: Michal Hocko <mhocko@suse.cz> Acked-by: David Rientjes <rientjes@gooogle.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/rtc/rtc-s3c.c: add .needs_src_clk to s3c6410 RTC data
Commit df9e26d093d3 ("rtc: s3c: add support for RTC of Exynos3250 SoC")
added an "rtc_src" DT property to specify the clock used as a source to
the S3C real-time clock.
Not all SoCs needs this so commit eaf3a659086e ("drivers/rtc/rtc-s3c.c:
fix initialization failure without rtc source clock") changed to check
the struct s3c_rtc_data .needs_src_clk to conditionally grab the clock.
But that commit didn't update the data for each IP version so the RTC
broke on the boards that needs a source clock. This is the case of at
least Exynos5250 and Exynos5440 which uses the s3c6410 RTC IP block.
This commit fixes the S3C rtc on the Exynos5250 Snow and Exynos5420
Peach Pit and Pi Chromebooks.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Chanwoo Choi <cw00.choi@samsung.com> Cc: Doug Anderson <dianders@chromium.org> Cc: Olof Johansson <olof@lixom.net> Cc: Kevin Hilman <khilman@linaro.org> Cc: Tyler Baker <tyler.baker@linaro.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark Fasheh [Thu, 12 Mar 2015 23:25:46 +0000 (16:25 -0700)]
ocfs2: make append_dio an incompat feature
It turns out that making this feature ro_compat isn't quite enough to
prevent accidental corruption on mount from older kernels. Ocfs2 (like
other file systems) will process orphaned inodes even when the user mounts
in 'ro' mode. So for the case of a filesystem not knowing the append_dio
feature, mounting the filesystem could result in orphaned-for-dio files
being deleted, which we clearly don't want.
So instead, turn this into an incompat flag.
Btw, this is kind of my fault - initially I asked that we add a flag to
cover the feature and even suggested that we use an ro flag. It wasn't
until I was looking through our commits for v4.0-rc1 that I realized we
actually want this to be incompat.
Signed-off-by: Mark Fasheh <mfasheh@suse.de> Cc: Joseph Qi <joseph.qi@huawei.com> Cc: Joel Becker <jlbec@evilplan.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman [Sat, 7 Mar 2015 15:20:48 +0000 (15:20 +0000)]
mm: thp: Return the correct value for change_huge_pmd
The wrong value is being returned by change_huge_pmd since commit 10c1045f28e8 ("mm: numa: avoid unnecessary TLB flushes when setting
NUMA hinting entries") which allows a fallthrough that tries to adjust
non-existent PTEs. This patch corrects it.
Linus Torvalds [Thu, 12 Mar 2015 16:45:46 +0000 (09:45 -0700)]
Merge tag 'pci-v4.0-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Here are a couple updates for v4.0.
One fixes a config accessor problem on APM X-Gene that we introduced
when switching to generic config accessors, and the other fixes an
older read-past-end-of-buffer problem in sysfs.
APM X-Gene host bridge driver
- Add register offset to config space base address (Feng Kan)
Miscellaneous
- Don't read past the end of sysfs "driver_override" buffer (Sasha Levin)"
* tag 'pci-v4.0-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: xgene: Add register offset to config space base address
PCI: Don't read past the end of sysfs "driver_override" buffer
Linus Torvalds [Thu, 12 Mar 2015 15:45:46 +0000 (08:45 -0700)]
mm: fix up numa read-only thread grouping logic
Dave Chinner reported that commit 4d9424669946 ("mm: convert
p[te|md]_mknonnuma and remaining page table manipulations") slowed down
his xfsrepair test enormously. In particular, it was using more system
time due to extra TLB flushing.
The ultimate reason turns out to be how the change to use the regular
page table accessor functions broke the NUMA grouping logic. The old
special mknuma/mknonnuma code accessed the page table present bit and
the magic NUMA bit directly, while the new code just changes the page
protections using PROT_NONE and the regular vma protections.
That sounds equivalent, and from a fault standpoint it really is, but a
subtle side effect is that the *other* protection bits of the page table
entries also change. And the code to decide how to group the NUMA
entries together used the writable bit to decide whether a particular
page was likely to be shared read-only or not.
And with the change to make the NUMA handling use the regular permission
setting functions, that writable bit was basically always cleared for
private mappings due to COW. So even if the page actually ends up being
written to in the end, the NUMA balancing would act as if it was always
shared RO.
This code is a heuristic anyway, so the fix - at least for now - is to
instead check whether the page is dirty rather than writable. The bit
doesn't change with protection changes.
NOTE! This also adds a FIXME comment to revisit this issue,
Not only should we probably re-visit the whole "is this a shared
read-only page" heuristic (we might want to take the vma permissions
into account and base this more on those than the per-page ones, and
also look at whether the particular access that triggers it is a write
or not), but the whole COW issue shows that we should think about the
NUMA fault handling some more.
For example, maybe we should do the early-COW thing that a regular fault
does. Or maybe we should accept that while using the same bits as
PROTNONE was a good thing (and got rid of the specual NUMA bit), we
might still want to just preseve the other protection bits across NUMA
faulting.
Those are bigger questions, left for later. This just fixes up the
heuristic so that it at least approximates working again. More analysis
and work needed.
Jakub Kicinski [Wed, 11 Mar 2015 17:35:36 +0000 (18:35 +0100)]
Revert "i2c: core: Dispose OF IRQ mapping at client removal time"
This reverts commit e4df3a0b6228
("i2c: core: Dispose OF IRQ mapping at client removal time")
Calling irq_dispose_mapping() will destroy the mapping and disassociate
the IRQ from the IRQ chip to which it belongs. Keeping it is OK, because
existent mappings are reused properly.
Also, this commit breaks drivers using devm* for IRQ management on
OF-based systems because devm* cleanup happens in device code, after
bus's remove() method returns.
Linus Torvalds [Wed, 11 Mar 2015 00:44:34 +0000 (17:44 -0700)]
Merge tag 'for-linus-20150310' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
* pxa3xx_nand
- fix timeout issues when draining the FIFO (BCH only)
- don't crash when no chip-selects are used
* hisi504_nand
- depend on HAS_DMA, to fix compile errors
* tag 'for-linus-20150310' of git://git.infradead.org/linux-mtd:
mtd: nand: MTD_NAND_HISI504 should depend on HAS_DMA
mtd: pxa3xx_nand: fix driver when num_cs is 0
mtd: nand: pxa3xx: Fix PIO FIFO draining
Linus Torvalds [Wed, 11 Mar 2015 00:36:19 +0000 (17:36 -0700)]
Merge tag 'iommu-fixes-v4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
"The patches contain:
- fix multiple ARM IOMMU drivers to behave well when the hardware is
not present
- mark MSM driver as broken
- fix build errors with the new ARM generic io-page-table code"
* tag 'iommu-fixes-v4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/io-pgtable-arm: Add built time dependency
iommu/msm: Mark driver BROKEN
iommu/rockchip: Play nice in multi-platform builds
iommu/omap: Play nice in multi-platform builds
iommu/exynos: Play nice in multi-platform builds
iommu/io-pgtable-arm: Fix self-test WARNs on i386
Linus Torvalds [Tue, 10 Mar 2015 01:59:50 +0000 (18:59 -0700)]
Merge git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm/s390 bugfixes from Marcelo Tosatti.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: s390: non-LPAR case obsolete during facilities mask init
KVM: s390: include guest facilities in kvm facility test
KVM: s390: fix in memory copy of facility lists
KVM: s390/cpacf: Fix kernel bug under z/VM
KVM: s390/cpacf: Enable key wrapping by default
Linus Torvalds [Tue, 10 Mar 2015 01:55:52 +0000 (18:55 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"One performance optimization for page_clear and a couple of bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: fix incorrect ASCE after crst_table_downgrade
s390/ftrace: fix crashes when switching tracers / add notrace to cpu_relax()
s390/pci: unify pci_iomap symbol exports
s390/pci: fix [un]map_resources sequence
s390: let the compiler do page clearing
s390/pci: fix possible information leak in mmio syscall
s390/dcss: array index 'i' is used before limits check.
s390/scm_block: fix off by one during cluster reservation
s390/jump label: improve and fix sanity check
s390/jump label: add missing jump_label_apply_nops() call
Linus Torvalds [Tue, 10 Mar 2015 01:44:06 +0000 (18:44 -0700)]
Merge tag 'trace-fixes-v4.0-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull seq-buf/ftrace fixes from Steven Rostedt:
"This includes fixes for seq_buf_bprintf() truncation issue. It also
contains fixes to ftrace when /proc/sys/kernel/ftrace_enabled and
function tracing are started. Doing the following causes some issues:
As well as with function tracing too. Pratyush Anand first reported
this issue to me and supplied a patch. When I tested this on my x86
test box, it caused thousands of backtraces and warnings to appear in
dmesg, which also caused a denial of service (a warning for every
function that was listed). I applied Pratyush's patch but it did not
fix the issue for me. I looked into it and found a slight problem
with trampoline accounting. I fixed it and sent Pratyush a patch, but
he said that it did not fix the issue for him.
I later learned tha Pratyush was using an ARM64 server, and when I
tested on my ARM board, I was able to reproduce the same issue as
Pratyush. After applying his patch, it fixed the problem. The above
test uncovered two different bugs, one in x86 and one in ARM and
ARM64. As this looked like it would affect PowerPC, I tested it on my
PPC64 box. It too broke, but neither the patch that fixed ARM or x86
fixed this box (the changes were all in generic code!). The above
test, uncovered two more bugs that affected PowerPC. Again, the
changes were only done to generic code. It's the way the arch code
expected things to be done that was different between the archs. Some
where more sensitive than others.
The rest of this series fixes the PPC bugs as well"
* tag 'trace-fixes-v4.0-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Fix ftrace enable ordering of sysctl ftrace_enabled
ftrace: Fix en(dis)able graph caller when en(dis)abling record via sysctl
ftrace: Clear REGS_EN and TRAMP_EN flags on disabling record via sysctl
seq_buf: Fix seq_buf_bprintf() truncation
seq_buf: Fix seq_buf_vprintf() truncation
1) nft_compat accidently truncates ethernet protocol to 8-bits, from
Arturo Borrero.
2) Memory leak in ip_vs_proc_conn(), from Julian Anastasov.
3) Don't allow the space required for nftables rules to exceed the
maximum value representable in the dlen field. From Patrick
McHardy.
4) bcm63xx_enet can accidently leave interrupts permanently disabled
due to errors in the NAPI polling exit logic. Fix from Nicolas
Schichan.
5) Fix OOPSes triggerable by the ping protocol module, due to missing
address family validations etc. From Lorenzo Colitti.
6) Don't use RCU locking in sleepable context in team driver, from Jiri
Pirko.
7) xen-netback miscalculates statistic offset pointers when reporting
the stats to userspace. From David Vrabel.
8) Fix a leak of up to 256 pages per VIF destroy in xen-netaback, also
from David Vrabel.
9) ip_check_defrag() cannot assume that skb_network_offset(),
particularly when it is used by the AF_PACKET fanout defrag code.
From Alexander Drozdov.
10) gianfar driver doesn't query OF node names properly when trying to
determine the number of hw queues available. Fix it to explicitly
check for OF nodes named queue-group. From Tobias Waldekranz.
11) MID field in macb driver should be 12 bits, not 16. From Punnaiah
Choudary Kalluri.
12) Fix unintentional regression in traceroute due to timestamp socket
option changes. Empty ICMP payloads should be allowed in
non-timestamp cases. From Willem de Bruijn.
13) When devices are unregistered, we have to get rid of AF_PACKET
multicast list entries that point to it via ifindex. Fix from
Francesco Ruggeri.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
tipc: fix bug in link failover handling
net: delete stale packet_mclist entries
net: macb: constify macb configuration data
MAINTAINERS: add Marc Kleine-Budde as co maintainer for CAN networking layer
MAINTAINERS: linux-can moved to github
can: kvaser_usb: Read all messages in a bulk-in URB buffer
can: kvaser_usb: Avoid double free on URB submission failures
can: peak_usb: fix missing ctrlmode_ init for every dev
can: add missing initialisations in CAN related skbuffs
ip: fix error queue empty skb handling
bgmac: Clean warning messages
tcp: align tcp_xmit_size_goal() on tcp_tso_autosize()
net: fec: fix unbalanced clk disable on driver unbind
net: macb: Correct the MID field length value
net: gianfar: correctly determine the number of queue groups
ipv4: ip_check_defrag should not assume that skb_network_offset is zero
net: bcmgenet: properly disable password matching
net: eth: xgene: fix booting with devicetree
bnx2x: Force fundamental reset for EEH recovery
xen-netback: refactor xenvif_handle_frag_list()
...
Linus Torvalds [Tue, 10 Mar 2015 01:00:25 +0000 (18:00 -0700)]
Merge tag 'regulator-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of driver specific fixes plus a fix for a regression in the
core where the updates to use sysfs group registration were overly
enthusiastic in eliding properties and removed some that had been
previously present"
* tag 'regulator-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Fix regression due to NULL constraints check
regulator: rk808: Set the enable time for LDOs
regulator: da9210: Mask all interrupt sources to deassert interrupt line
Linus Torvalds [Tue, 10 Mar 2015 00:50:02 +0000 (17:50 -0700)]
Merge tag 'spi-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A collection of driver specific fixes to which the usual comments
about them being important if you see them mostly apply (except for
the comment fix). The pl022 one is particularly nasty for anyone
affected by it"
* tag 'spi-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: pl022: Fix race in giveback() leading to driver lock-up
spi: dw-mid: avoid potential NULL dereference
spi: img-spfi: Verify max spfi transfer length
spi: fix a typo in comment.
spi: atmel: Fix interrupt setup for PDC transfers
spi: dw: revisit FIFO size detection again
spi: dw-pci: correct number of chip selects
drivers: spi: ti-qspi: wait for busy bit clear before data write/read
Linus Torvalds [Tue, 10 Mar 2015 00:45:34 +0000 (17:45 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull tpm fixes from James Morris:
"fixes for the TPM driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
tpm: fix call order in tpm-chip.c
tpm/ibmvtpm: Additional LE support for tpm_ibmvtpm_send
Linus Torvalds [Tue, 10 Mar 2015 00:35:29 +0000 (17:35 -0700)]
Merge tag 'fbdev-fixes-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev fixes from Tomi Valkeinen:
- Fix regression in with omapdss when using i2c displays
- Fix possible null deref in fbmon
- Check kalloc return value in AMBA CLCD
* tag 'fbdev-fixes-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
OMAPDSS: fix regression with display sysfs files
video: fbdev: fix possible null dereference
video: ARM CLCD: Add missing error check for devm_kzalloc
Linus Torvalds [Tue, 10 Mar 2015 00:30:09 +0000 (17:30 -0700)]
Merge branch 'for-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"The cgroup iteration update two years ago and the recent cpuset
restructuring introduced regressions in subset of cpuset
configurations. Three patches to fix them.
All are marked for -stable"
* 'for-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cpuset: Fix cpuset sched_relax_domain_level
cpuset: fix a warning when clearing configured masks in old hierarchy
cpuset: initialize effective masks when clone_children is enabled
Linus Torvalds [Tue, 10 Mar 2015 00:00:54 +0000 (17:00 -0700)]
Merge branch 'for-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fix from Tejun Heo:
"One fix patch for a subtle livelock condition which can happen on
PREEMPT_NONE kernels involving two racing cancel_work calls. Whoever
comes in the second has to wait for the previous one to finish. This
was implemented by making the later one block for the same condition
that the former would be (work item completion) and then loop and
retest; unfortunately, depending on the wake up order, the later one
could lock out the former one to finish by busy looping on the cpu.
This is fixed by implementing explicit wait mechanism. Work item
might not belong anywhere at this point and there's remote possibility
of thundering herd problem. I originally tried to use bit_waitqueue
but it didn't work for static work items on modules. It's currently
using single wait queue with filtering wake up function and exclusive
wakeup. If this ever becomes a problem, which is not very likely, we
can try to figure out a way to piggy back on bit_waitqueue"
* 'for-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: fix hang involving racing cancel[_delayed]_work_sync()'s for PREEMPT_NONE
Jon Paul Maloy [Mon, 9 Mar 2015 20:16:22 +0000 (16:16 -0400)]
tipc: fix bug in link failover handling
In commit c637c1035534867b85b78b453c38c495b58e2c5a
("tipc: resolve race problem at unicast message reception") we
introduced a new mechanism for delivering buffers upwards from link
to socket layer.
That code contains a bug in how we handle the new link input queue
during failover. When a link is reset, some of its users may be blocked
because of congestion, and in order to resolve this, we add any pending
wakeup pseudo messages to the link's input queue, and deliver them to
the socket. This misses the case where the other, remaining link also
may have congested users. Currently, the owner node's reference to the
remaining link's input queue is unconditionally overwritten by the
reset link's input queue. This has the effect that wakeup events from
the remaining link may be unduely delayed (but not lost) for a
potentially long period.
We fix this by adding the pending events from the reset link to the
input queue that is currently referenced by the node, whichever one
it is.
This commit should be applied to both net and net-next.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When an interface is deleted from a net namespace the ifindex in the
corresponding entries in PF_PACKET sockets' mclists becomes stale.
This can create inconsistencies if later an interface with the same ifindex
is moved from a different namespace (not that unlikely since ifindexes are
per-namespace).
In particular we saw problems with dev->promiscuity, resulting
in "promiscuity touches roof, set promiscuity failed. promiscuity
feature of device might be broken" warnings and EOVERFLOW failures of
setsockopt(PACKET_ADD_MEMBERSHIP).
This patch deletes the mclist entries for interfaces that are deleted.
Since this now causes setsockopt(PACKET_DROP_MEMBERSHIP) to fail with
EADDRNOTAVAIL if called after the interface is deleted, also make
packet_mc_drop not fail.
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 9 Mar 2015 19:41:00 +0000 (15:41 -0400)]
Merge tag 'linux-can-fixes-for-4.0-20150309' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-03-09
this is a pull request for net/master for the 4.0 release cycle, it consists of
6 patches:
A patch by Oliver Hartkopp fixes a long outstanding bug in the infrastructure,
which leads to skb_under_panics when CAN interfaces are used by AF_PACKET
sockets e.g. by dhclient. Stephane Grosjean contributes a patch for the
peak_usb driver which adds a missing initialization. Two patches by Ahmed S.
Darwish fix problems in the kvaser_usb driver. Followed by two patches by
myself, updating the MAINTAINERS file
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ftrace: Fix ftrace enable ordering of sysctl ftrace_enabled
Some archs (specifically PowerPC), are sensitive with the ordering of
the enabling of the calls to function tracing and setting of the
function to use to be traced.
That is, update_ftrace_function() sets what function the ftrace_caller
trampoline should call. Some archs require this to be set before
calling ftrace_run_update_code().
Another bug was discovered, that ftrace_startup_sysctl() called
ftrace_run_update_code() directly. If the function the ftrace_caller
trampoline changes, then it will not be updated. Instead a call
to ftrace_startup_enable() should be called because it tests to see
if the callback changed since the code was disabled, and will
tell the arch to update appropriately. Most archs do not need this
notification, but PowerPC does.
The problem could be seen by the following commands:
Pratyush Anand [Fri, 6 Mar 2015 18:28:06 +0000 (23:58 +0530)]
ftrace: Fix en(dis)able graph caller when en(dis)abling record via sysctl
When ftrace is enabled globally through the proc interface, we must check if
ftrace_graph_active is set. If it is set, then we should also pass the
FTRACE_START_FUNC_RET command to ftrace_run_update_code(). Similarly, when
ftrace is disabled globally through the proc interface, we must check if
ftrace_graph_active is set. If it is set, then we should also pass the
FTRACE_STOP_FUNC_RET command to ftrace_run_update_code().
Since ftrace_enabled = 0, ftrace_enable_ftrace_graph_caller() is never
called.
# echo 1 > /proc/sys/kernel/ftrace_enabled
Now ftrace_enabled will be set to true, but still
ftrace_enable_ftrace_graph_caller() will not be called, which is not
desired.
Further if we execute the following after this:
# echo nop > /sys/kernel/debug/tracing/current_tracer
Now since ftrace_enabled is set it will call
ftrace_disable_ftrace_graph_caller(), which causes a kernel warning on
the ARM platform.
On the ARM platform, when ftrace_enable_ftrace_graph_caller() is called,
it checks whether the old instruction is a nop or not. If it's not a nop,
then it returns an error. If it is a nop then it replaces instruction at
that address with a branch to ftrace_graph_caller.
ftrace_disable_ftrace_graph_caller() behaves just the opposite. Therefore,
if generic ftrace code ever calls either ftrace_enable_ftrace_graph_caller()
or ftrace_disable_ftrace_graph_caller() consecutively two times in a row,
then it will return an error, which will cause the generic ftrace code to
raise a warning.
Note, x86 does not have an issue with this because the architecture
specific code for ftrace_enable_ftrace_graph_caller() and
ftrace_disable_ftrace_graph_caller() does not check the previous state,
and calling either of these functions twice in a row has no ill effect.
ftrace: Clear REGS_EN and TRAMP_EN flags on disabling record via sysctl
When /proc/sys/kernel/ftrace_enabled is set to zero, all function
tracing is disabled. But the records that represent the functions
still hold information about the ftrace_ops that are hooked to them.
ftrace_ops may request "REGS" (have a full set of pt_regs passed to
the callback), or "TRAMP" (the ops has its own trampoline to use).
When the record is updated to represent the state of the ops hooked
to it, it sets "REGS_EN" and/or "TRAMP_EN" to state that the callback
points to the correct trampoline (REGS has its own trampoline).
When ftrace_enabled is set to zero, all ftrace locations are a nop,
so they do not point to any trampoline. But the _EN flags are still
set. This can cause the accounting to go wrong when ftrace_enabled
is cleared and an ops that has a trampoline is registered or unregistered.
For example, the following will cause ftrace to crash:
As function_graph uses a trampoline, when ftrace_enabled is set to zero
the updates to the record are not done. When enabling function_graph
again, the record will still have the TRAMP_EN flag set, and it will
look for an op that has a trampoline other than the function_graph
ops, and fail to find one.
Ahmed S. Darwish [Thu, 26 Feb 2015 15:22:02 +0000 (10:22 -0500)]
can: kvaser_usb: Read all messages in a bulk-in URB buffer
The Kvaser firmware can only read and write messages that are
not crossing the USB endpoint's wMaxPacketSize boundary. While
receiving commands from the CAN device, if the next command in
the same URB buffer crossed that max packet size boundary, the
firmware puts a zero-length placeholder command in its place
then moves the real command to the next boundary mark.
The driver did not recognize such behavior, leading to missing
a good number of rx events during a heavy rx load session.
Moreover, a tx URB context only gets freed upon receiving its
respective tx ACK event. Over time, the free tx URB contexts
pool gets depleted due to the missing ACK events. Consequently,
the netif transmission queue gets __permanently__ stopped; no
frames could be sent again except after restarting the CAN
newtwork interface.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Ahmed S. Darwish [Thu, 26 Feb 2015 15:20:11 +0000 (10:20 -0500)]
can: kvaser_usb: Avoid double free on URB submission failures
Upon a URB submission failure, the driver calls usb_free_urb()
but then manually frees the URB buffer by itself. Meanwhile
usb_free_urb() has alredy freed out that transfer buffer since
we're the only code path holding a reference to this URB.
Remove two of such invalid manual free().
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
can: peak_usb: fix missing ctrlmode_ init for every dev
Fixes a missing initialization of ctrlmode and ctrlmode_supported fields,
for all other CAN devices than the first one. This fix only concerns
the PCAN-USB Pro FD dual-channels CAN-FD device made by PEAK-System.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When reading from the error queue, msg_name and msg_control are only
populated for some errors. A new exception for empty timestamp skbs
added a false positive on icmp errors without payload.
`traceroute -M udpconn` only displayed gateways that return payload
with the icmp error: the embedded network headers are pulled before
sock_queue_err_skb, leaving an skb with skb->len == 0 otherwise.
Fix this regression by refining when msg_name and msg_control
branches are taken. The solutions for the two fields are independent.
msg_name only makes sense for errors that configure serr->port and
serr->addr_offset. Test the first instead of skb->len. This also fixes
another issue. saddr could hold the wrong data, as serr->addr_offset
is not initialized in some code paths, pointing to the start of the
network header. It is only valid when serr->port is set (non-zero).
msg_control support differs between IPv4 and IPv6. IPv4 only honors
requests for ICMP and timestamps with SOF_TIMESTAMPING_OPT_CMSG. The
skb->len test can simply be removed, because skb->dev is also tested
and never true for empty skbs. IPv6 honors requests for all errors
aside from local errors and timestamps on empty skbs.
In both cases, make the policy more explicit by moving this logic to
a new function that decides whether to process msg_control and that
optionally prepares the necessary fields in skb->cb[]. After this
change, the IPv4 and IPv6 paths are more similar.
The last case is rxrpc. Here, simply refine to only match timestamps.
Fixes: 49ca0d8bfaf3 ("net-timestamp: no-payload option") Reported-by: Jan Niehusmann <jan@gondor.com> Signed-off-by: Willem de Bruijn <willemb@google.com>
----
Changes
v1->v2
- fix local origin test inversion in ip6_datagram_support_cmsg
- make v4 and v6 code paths more similar by introducing analogous
ipv4_datagram_support_cmsg
- fix compile bug in rxrpc Signed-off-by: David S. Miller <davem@davemloft.net>
On my test environment the throughput of a file transfer drops
from 4.4MBps to 116KBps due the number of repeated warning
messages. This patch removes the warning messages as DMA works
correctly with addresses using 0xC0000000 bits.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Acked-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 8 Mar 2015 19:47:18 +0000 (12:47 -0700)]
Merge tag 'usb-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here's a round of USB fixes for 4.0-rc3.
Nothing major, the usual gadget, xhci and usb-serial fixes and a few
new device ids as well.
All have been in linux-next successfully"
* tag 'usb-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (36 commits)
xhci: Workaround for PME stuck issues in Intel xhci
xhci: fix reporting of 0-sized URBs in control endpoint
usb: ftdi_sio: Add jtag quirk support for Cyber Cortex AV boards
USB: ch341: set tty baud speed according to tty struct
USB: serial: cp210x: Adding Seletek device id's
USB: pl2303: disable break on shutdown
USB: mxuport: fix null deref when used as a console
USB: serial: clean up bus probe error handling
USB: serial: fix port attribute-creation race
USB: serial: fix tty-device error handling at probe
USB: serial: fix potential use-after-free after failed probe
USB: console: add dummy __module_get
USB: ftdi_sio: add PIDs for Actisense USB devices
Revert "USB: serial: make bulk_out_size a lower limit"
cdc-acm: Add support for Denso cradle CU-321
usb-storage: support for more than 8 LUNs
uas: Add US_FL_NO_REPORT_OPCODES for JMicron JMS539
USB: usbfs: don't leak kernel data in siginfo
xhci: Clear the host side toggle manually when endpoint is 'soft reset'
xhci: Allocate correct amount of scratchpad buffers
...
Linus Torvalds [Sun, 8 Mar 2015 19:25:40 +0000 (12:25 -0700)]
Merge tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tty and serial driver fixes for 4.0-rc3.
Along with the atime fix that you know about, here are some other
serial driver bugfixes as well. Most notable is a wait_until_sent
bugfix that was traced back to being around since before 2.6.12 that
Johan has fixed up.
All have been in linux-next successfully"
* tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
TTY: fix tty_wait_until_sent maximum timeout
TTY: fix tty_wait_until_sent on 64-bit machines
USB: serial: fix infinite wait_until_sent timeout
TTY: bfin_jtag_comm: remove incorrect wait_until_sent operation
net: irda: fix wait_until_sent poll timeout
serial: uapi: Declare all userspace-visible io types
serial: core: Fix iotype userspace breakage
serial: sprd: Fix missing spin_unlock in sprd_handle_irq()
console: Fix console name size mismatch
tty: fix up atime/mtime mess, take four
serial: 8250_dw: Fix get_mctrl behaviour
serial:8250:8250_pci: delete unneeded quirk entries
serial:8250:8250_pci: fix redundant entry report for WCH_CH352_2S
Change email address for 8250_pci
serial: 8250: Revert "tty: serial: 8250_core: read only RX if there is something in the FIFO"
Revert "tty/serial: of_serial: add DT alias ID handling"
Linus Torvalds [Sun, 8 Mar 2015 19:15:47 +0000 (12:15 -0700)]
Merge tag 'char-misc-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are two char/misc fixes for 4.0-rc3.
One is a reported binder driver fix needed due to a change in the mm
core that happened in 4.0-rc1. Another is a mei driver fix that
resolves a reported issue in that driver.
Both have been in linux-next for a while"
* tag 'char-misc-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mei: make device disabled on stop unconditionally
android: binder: fix binder mmap failures
Linus Torvalds [Sun, 8 Mar 2015 18:51:04 +0000 (11:51 -0700)]
Merge tag 'cc-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull "code of conflict" from Greg KH:
"This file tries to set the rational basis for our code reviews, gives
some advice on how to conduct them, and provides an excalation channel
for any kernel developers if they so desire it"
[ Let's see how this works ]
* tag 'cc-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Code of Conflict
Input: psmouse - disable "palm detection" in the focaltech driver
Apparently, the threshold for large contact area seems to be rather low on
some devices, causing the touchpad to frequently freeze during normal
usage. Because we do now know how we are supposed to use the value in
question, this commit just drops the related code completely.
Input: psmouse - disable changing resolution/rate/scale for FocalTech
These PS/2 commands make some touchpads stop responding, so this commit
adds some dummy functions to replace the generic implementation. Because
scale changes were not encapsulated in a method of struct psmouse yet, this
commit adds a method set_scale to psmouse.
Input: psmouse - ensure that focaltech reports consistent coordinates
We don't know whether x_max or y_max really hold the maximum possible
coordinates, and we don't know for sure whether we correctly interpret the
coordinates sent by the touchpad, so we clamp the reported values to
prevent confusion in userspace code.
Linus Torvalds [Sat, 7 Mar 2015 19:31:17 +0000 (11:31 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
"arm64 and generic kernel/module.c (acked by Rusty) fixes for
CONFIG_DEBUG_SET_MODULE_RONX"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
kernel/module.c: Update debug alignment after symtable generation
arm64: Don't use is_module_addr in setting page attributes
Johan Hovold [Wed, 4 Mar 2015 09:39:07 +0000 (10:39 +0100)]
TTY: fix tty_wait_until_sent maximum timeout
Currently tty_wait_until_sent may take up to twice as long as the
requested timeout while waiting for driver and hardware buffers to
drain.
Fix this by taking the remaining number of jiffies after waiting for
driver buffers to drain into account so that the timeout actually
becomes a maximum timeout as it is documented to be.
Note that this specifically implies tighter timings when closing a port
as a consequence of actually honouring the port closing-wait setting
for drivers relying on tty_wait_until_sent_from_close (e.g. via
tty_port_close_start).
Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Wed, 4 Mar 2015 09:39:06 +0000 (10:39 +0100)]
TTY: fix tty_wait_until_sent on 64-bit machines
Fix overflow bug in tty_wait_until_sent on 64-bit machines, where an
infinite timeout (0) would be passed to the underlying tty-driver's
wait_until_sent-operation as a negative timeout (-1), causing it to
return immediately.
This manifests itself for example as tcdrain() returning immediately,
drivers not honouring the drain flags when setting terminal attributes,
or even dropped data on close as a requested infinite closing-wait
timeout would be ignored.
The first symptom was reported by Asier LLANO who noted that tcdrain()
returned prematurely when using the ftdi_sio usb-serial driver.
Fix this by passing 0 rather than MAX_SCHEDULE_TIMEOUT (LONG_MAX) to the
underlying tty driver.
Note that the serial-core wait_until_sent-implementation is not affected
by this bug due to a lucky chance (comparison to an unsigned maximum
timeout), and neither is the cyclades one that had an explicit check for
negative timeouts, but all other tty drivers appear to be affected.
Remove incorrect and redundant wait_until_sent operation, which waits
for the driver buffer rather than any hardware buffers to drain,
something which is already taken care of by the tty layer (and
chars_in_buffer).
Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 1 Mar 2015 15:24:28 +0000 (10:24 -0500)]
serial: uapi: Declare all userspace-visible io types
ioctl(TIOCGSERIAL|TIOCSSERIAL) report and can change the port->iotype.
UART drivers use the UPIO_* definitions, but the uapi header defines
parallel values and userspace uses these parallel values for ioctls;
thus the userspace values are definitive.
Define UPIO_* iotypes in terms of the uapi defines, SERIAL_IO_*;
extend the uapi defines to include all values in use by the serial
core.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 1 Mar 2015 15:18:16 +0000 (10:18 -0500)]
serial: core: Fix iotype userspace breakage
commit 3ffb1a8193bea ("serial: core: Add big-endian iotype")
re-numbered userspace-dependent values; ioctl(TIOCSSERIAL) can
assign the port iotype (which is expected to match the selected
i/o accessors), so iotype values must not be changed.
Cc: Kevin Cernekee <cernekee@gmail.com> Cc: <stable@vger.kernel.org> # 3.19+ Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Reviewed-by: Kevin Cernekee <cernekee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Axel Lin [Mon, 16 Feb 2015 14:39:04 +0000 (22:39 +0800)]
serial: sprd: Fix missing spin_unlock in sprd_handle_irq()
Fix return from sprd_handle_irq() with spin_lock held.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 1 Mar 2015 15:11:05 +0000 (10:11 -0500)]
console: Fix console name size mismatch
commit 6ae9200f2cab7 ("enlarge console.name") increased the storage
for the console name to 16 bytes, but not the corresponding
struct console_cmdline::name storage. Console names longer than
8 bytes cause read beyond end-of-string and failure to match
console; I'm not sure if there are other unexpected consequences.
But it still misses one point. As John Paul correctly points out, we
do not care about setting date. If somebody ever changes wall
time backwards (by mistake for example), tty timestamps are never
updated until the original wall time passes.
So check the absolute difference of times and if it large than "8
seconds or so", always update the time. That means we will update
immediatelly when changing time. Ergo, CAP_SYS_TIME can foul the
check, but it was always that way.
Thanks John for serving me this so nicely debugged.
Signed-off-by: Jiri Slaby <jslaby@suse.cz> Reported-by: John Paul Perry <john_paul.perry@alcatel-lucent.com> Cc: <stable@vger.kernel.org> # all, as b0b885657 was backported Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Desmond Liu [Fri, 27 Feb 2015 00:35:57 +0000 (16:35 -0800)]
serial: 8250_dw: Fix get_mctrl behaviour
Fixed behaviour of get_mctrl() serial driver function as documented in:
https://www.kernel.org/doc/Documentation/serial/driver
Added device-tree properties 'dcd-override', 'dsr-override',
'cts-override', and 'ri-override' specific to the Synopsis 8250
DesignWare UART driver. Allows one to force Data Carrier Detect,
Clear To Send, and Data Set Ready signals to permanently be reported as
active. The Ring indicator can be forced to be reported as inactive.
It is possible that if modem control signalling is enabled on a port
that doesn't have these pins (e.g. - a simple two wire Tx/Rx port), the
driver can hang indefinitely waiting for the state to change. The new
DT properties allow the driver to ignore the state of these pins on
serial ports that don't support them, as recommended in the kernel
documentation.
Reported-by: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Wang YanQing <udknight@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The conditional RX-FIFO read seems to cause spurious interrupts and we
see just:
|serial8250: too much work for irq29
The previous behaviour was "default" for decades and Marvell's 88f6282 SoC
might not be the only that relies on it. Therefore the Omap fix is
reverted for now.
Fixes: 0aa525d11859 ("tty: serial: 8250_core: read only RX if there is
something in the FIFO") Reported-By: Nicolas Schichan <nschichan@freebox.fr> Debuged-By: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sat, 7 Mar 2015 00:54:22 +0000 (16:54 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Radeon, imx, msm, and i915 fixes.
The msm, imx and i915 ones are fairly run of the mill.
Radeon had some DP audio and posting reads for irq fixes, along with a
fix for 32-bit kernels with new cards, we were using unsigned long to
represent GPU side memory space, but since that changed size on 32 vs
64 cards with lots of VRAM failed, so the change has no effect on
x86-64, just moves to using uint64_t instead"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (35 commits)
drm/msm: kexec fixes
drm/msm/mdp5: fix cursor blending
drm/msm/mdp5: fix cursor ROI
drm/msm/atomic: Don't leak atomic commit object when commit fails
drm/msm/mdp5: Avoid flushing registers when CRTC is disabled
drm/msm: update generated headers (add 6th lm.base entry)
drm/msm/mdp5: fixup "drm/msm: fix fallout of atomic dpms changes"
drm/ttm: device address space != CPU address space
drm/mm: Support 4 GiB and larger ranges
drm/i915: gen4: work around hang during hibernation
drm/i915: Check for driver readyness before handling an underrun interrupt
drm/radeon: fix interlaced modes on DCE8
drm/radeon: fix DRM_IOCTL_RADEON_CS oops
drm/radeon: do a posting read in cik_set_irq
drm/radeon: do a posting read in si_set_irq
drm/radeon: do a posting read in evergreen_set_irq
drm/radeon: do a posting read in r600_set_irq
drm/radeon: do a posting read in rs600_set_irq
drm/radeon: do a posting read in r100_set_irq
radeon/audio: fix DP audio on DCE6
...
This patch marks baytrail_i2c_acquire() that it might sleep. Also it chages
while-loop to do-while and, though it is matter of taste, gives a chance to
check one more time before report a timeout.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: David E. Box <david.e.box@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It seems the idea behind the cross-check is to prevent acquire semaphore when
there is no release callback and vice versa. Thus, patch fixes a typo.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: David E. Box <david.e.box@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>