"f3 a5" is a "rep movsw" instruction, which should not be intercepted
at all. Commit c44b4c6ab80e ("KVM: emulate: clean up initializations in
init_decode_cache") reduced the number of fields cleared by
init_decode_cache() claiming that they are being cleared elsewhere,
'intercept', however, is left uncleared if the instruction does not have
any of the "slow path" flags (NotImpl, Stack, Op3264, Sse, Mmx, CheckPerm,
NearBranch, No16 and of course Intercept itself).
Fixes: c44b4c6ab80e ("KVM: emulate: clean up initializations in init_decode_cache") Fixes: 07721feee46b ("KVM: nVMX: Don't emulate instructions in guest mode") Cc: stable@vger.kernel.org Suggested-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
with the way fs/namei.c:do_last() had been done, ->atomic_open()
instances needed to recognize the case when existing file got
found with O_EXCL|O_CREAT, either by falling back to finish_no_open()
or failing themselves. gfs2 one didn't.
several iterations of ->atomic_open() calling conventions ago, we
used to need fput() if ->atomic_open() failed at some point after
successful finish_open(). Now (since 2016) it's not needed -
struct file carries enough state to make fput() work regardless
of the point in struct file lifecycle and discarding it on
failure exits in open() got unified. Unfortunately, I'd missed
the fact that we had an instance of ->atomic_open() (cifs one)
that used to need that fput(), as well as the stale comment in
finish_open() demanding such late failure handling. Trivially
fixed...
Fixes: fe9ec8291fca "do_last(): take fput() on error after opening to out:" Cc: stable@kernel.org # v4.7+ Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Before rebooting the box, a "ssh sync" is called to the test machine to see
if it is alive or not. But if the test machine is in a partial state, that
ssh may never actually finish, and the ktest test hangs.
Add a 10 second timeout to the sync test, which will fail after 10 seconds
and then cause the test to reboot the test machine.
Cc: stable@vger.kernel.org Fixes: 6474ace999edd ("ktest.pl: Powercycle the box on reboot if no connection can be made") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Variable grph_obj_type is being assigned twice, one of these is
redundant so remove it.
Addresses-Coverity: ("Evaluation order violation") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
wq_select_unbound_cpu() is designed for unbound workqueues only, but
it's wrongly called when using a bound workqueue too.
Fixing this ensures work queued to a bound workqueue with
cpu=WORK_CPU_UNBOUND always runs on the local CPU.
Before, that would happen only if wq_unbound_cpumask happened to include
it (likely almost always the case), or was empty, or we got lucky with
forced round-robin placement. So restricting
/sys/devices/virtual/workqueue/cpumask to a small subset of a machine's
CPUs would cause some bound work items to run unexpectedly there.
Fixes: ef557180447f ("workqueue: schedule WORK_CPU_UNBOUND work on wq_unbound_cpumask CPUs") Cc: stable@vger.kernel.org # v4.5+ Signed-off-by: Hillf Danton <hdanton@sina.com>
[dj: massage changelog] Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com> Cc: Tejun Heo <tj@kernel.org> Cc: Lai Jiangshan <jiangshanlai@gmail.com> Cc: linux-kernel@vger.kernel.org Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Quoting from the comment describing the WARN functions in
include/asm-generic/bug.h:
* WARN(), WARN_ON(), WARN_ON_ONCE, and so on can be used to report
* significant kernel issues that need prompt attention if they should ever
* appear at runtime.
*
* Do not use these macros when checking for invalid external inputs
The (buggy) firmware tables which the dmar code was calling WARN_TAINT
for really are invalid external inputs. They are not under the kernel's
control and the issues in them cannot be fixed by a kernel update.
So logging a backtrace, which invites bug reports to be filed about this,
is not helpful.
Fixes: 556ab45f9a77 ("ioat2: catch and recover from broken vtd configurations v6") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Lu Baolu <baolu.lu@linux.intel.com> Link: https://lore.kernel.org/r/20200309182510.373875-1-hdegoede@redhat.com BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=701847 Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since nobody else is going to restart our hw_queue for us, the
blk_mq_start_stopped_hw_queues() is in virtblk_done() is not sufficient
necessarily sufficient to ensure that the queue will get started again.
In case of global resource outage (-ENOMEM because mapping failure,
because of swiotlb full) our virtqueue may be empty and we can get
stuck with a stopped hw_queue.
Let us not stop the queue on arbitrary errors, but only on -EONSPC which
indicates a full virtqueue, where the hw_queue is guaranteed to get
started by virtblk_done() before when it makes sense to carry on
submitting requests. Let us also remove a stale comment.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com> Cc: Jens Axboe <axboe@kernel.dk> Fixes: f7728002c1c7 ("virtio_ring: fix return code on DMA mapping fails") Link: https://lore.kernel.org/r/20200213123728.61216-2-pasic@linux.ibm.com Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
PF_EXITING is set earlier than actual removal from css_set when a task
is exitting. This can confuse cgroup.procs readers who see no PF_EXITING
tasks, however, rmdir is checking against css_set membership so it can
transitionally fail with EBUSY.
Fix this by listing tasks that weren't unlinked from css_set active
lists.
It may happen that other users of the task iterator (without
CSS_TASK_ITER_PROCS) spot a PF_EXITING task before cgroup_exit(). This
is equal to the state before commit c03cd7738a83 ("cgroup: Include dying
leaders with live threads in PROCS iterations") but it may be reviewed
later.
Reported-by: Suren Baghdasaryan <surenb@google.com> Fixes: c03cd7738a83 ("cgroup: Include dying leaders with live threads in PROCS iterations") Signed-off-by: Michal Koutný <mkoutny@suse.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output:
1) dd bs=1 skip output of each 2nd elements
$ dd if=/sys/fs/cgroup/cgroup.procs bs=8 count=1
2
3
4
5
1+0 records in
1+0 records out
8 bytes copied, 0,000267297 s, 29,9 kB/s
[test@localhost ~]$ dd if=/sys/fs/cgroup/cgroup.procs bs=1 count=8
2
4 <<< NB! 3 was skipped
6 <<< ... and 5 too
8 <<< ... and 7
8+0 records in
8+0 records out
8 bytes copied, 5,2123e-05 s, 153 kB/s
This happen because __cgroup_procs_start() makes an extra
extra cgroup_procs_next() call
2) read after lseek beyond end of file generates whole last line.
3) read after lseek into middle of last line generates
expected rest of last line and unexpected whole line once again.
Additionally patch removes an extra position index changes in
__cgroup_procs_start()
IPvlan in L3 mode discards outbound multicast packets but performs
the check before ensuring the ether-header is set or not. This is
an error that Eric found through code browsing.
Fixes: 2ad7bf363841 (“ipvlan: Initial check-in of the IPVLAN driver.”) Signed-off-by: Mahesh Bandewar <maheshb@google.com> Reported-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently, if IPv6 is enabled on top of an ipvlan device in l3
mode, the following warning message:
Dropped {multi|broad}cast of type= [86dd]
is emitted every time that a RS is generated and dmseg is soon
filled with irrelevant messages. Replace pr_warn with pr_debug,
to preserve debuggability, without scaring the sysadmin.
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There is a problem when ipvlan slaves are created on a master device that
is a vmxnet3 device (ipvlan in VMware guests). The vmxnet3 driver does not
support unicast address filtering. When an ipvlan device is brought up in
ipvlan_open(), the ipvlan driver calls dev_uc_add() to add the hardware
address of the vmxnet3 master device to the unicast address list of the
master device, phy_dev->uc. This inevitably leads to the vmxnet3 master
device being forced into promiscuous mode by __dev_set_rx_mode().
Promiscuous mode is switched on the master despite the fact that there is
still only one hardware address that the master device should use for
filtering in order for the ipvlan device to be able to receive packets.
The comment above struct net_device describes the uc_promisc member as a
"counter, that indicates, that promiscuous mode has been enabled due to
the need to listen to additional unicast addresses in a device that does
not implement ndo_set_rx_mode()". Moreover, the design of ipvlan
guarantees that only the hardware address of a master device,
phy_dev->dev_addr, will be used to transmit and receive all packets from
its ipvlan slaves. Thus, the unicast address list of the master device
should not be modified by ipvlan_open() and ipvlan_stop() in order to make
ipvlan a workable option on masters that do not support unicast address
filtering.
Fixes: 2ad7bf3638411 ("ipvlan: Initial check-in of the IPVLAN driver") Reported-by: Per Sundstrom <per.sundstrom@redqube.se> Signed-off-by: Jiri Wiesner <jwiesner@suse.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Acked-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In commit 1ec17dbd90f8 ("inet_diag: fix reporting cgroup classid and
fallback to priority") croup classid reporting was fixed. But this works
only for TCP sockets because for other socket types icsk parameter can
be NULL and classid code path is skipped. This change moves classid
handling to inet_diag_msg_attrs_fill() function.
Also inet_diag_msg_attrs_size() helper was added and addends in
nlmsg_new() were reordered to save order from inet_sk_diag_fill().
Fixes: 1ec17dbd90f8 ("inet_diag: fix reporting cgroup classid and fallback to priority") Signed-off-by: Dmitry Yakunin <zeil@yandex-team.ru> Reviewed-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The Rx bound multicast packets are deferred to a workqueue and
macvlan can also suffer from the same attack that was discovered
by Syzbot for IPvlan. This solution is not as effective as in
IPvlan. IPvlan defers all (Tx and Rx) multicast packet processing
to a workqueue while macvlan does this way only for the Rx. This
fix should address the Rx codition to certain extent.
Tx is still suseptible. Tx multicast processing happens when
.ndo_start_xmit is called, hence we cannot add cond_resched().
However, it's not that severe since the user which is generating
/ flooding will be affected the most.
Fixes: 412ca1550cbe ("macvlan: Move broadcasts into a work queue") Signed-off-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
fec_enet_set_coalesce() validates the previously set params
and if they are within range proceeds to apply the new ones.
The new ones, however, are not validated. This seems backwards,
probably a copy-paste error?
Compile tested only.
Fixes: d851b47b22fc ("net: fec: add interrupt coalescence feature support") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Before accessing various fields in IPV4 network header
and TCP header, make sure the packet :
- Has IP version 4 (ip->version == 4)
- Has not a silly network length (ip->ihl >= 5)
- Is big enough to hold network and transport headers
- Has not a silly TCP header size (th->doff >= sizeof(struct tcphdr) / 4)
Similar to commit 38f88c454042 ("bonding/alb: properly access headers
in bond_alb_xmit()"), we need to make sure arp header was pulled
in skb->head before blindly accessing it in rlb_arp_xmit().
Remove arp_pkt() private helper, since it is more readable/obvious
to have the following construct back to back :
if (!pskb_network_may_pull(skb, sizeof(*arp)))
return NULL;
arp = (struct arp_pkt *)skb_network_header(skb);
So far we have the unfortunate situation that mdio_bus_phy_may_suspend()
is called in suspend AND resume path, assuming that function result is
the same. After the original change this is no longer the case,
resulting in broken resume as reported by Geert.
To fix this call mdio_bus_phy_may_suspend() in the suspend path only,
and let the phy_device store the info whether it was suspended by
MDIO bus PM.
Fixes: 503ba7c69610 ("net: phy: Avoid multiple suspends") Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Tested-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Add missing attribute validation for NFC_ATTR_SE_INDEX
to the netlink policy.
Fixes: 5ce3f32b5264 ("NFC: netlink: SE API implementation") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Add missing attribute validation for TEAM_ATTR_OPTION_PORT_IFINDEX
to the netlink policy.
Fixes: 80f7c6683fe0 ("team: add support for per-port options") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Add missing attribute validation for TCA_FQ_ORPHAN_MASK
to the netlink policy.
Fixes: 06eb395fa985 ("pkt_sched: fq: better control of DDOS traffic") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Add missing attribute validation for IFLA_CAN_TERMINATION
to the netlink policy.
Fixes: 12a6075cabc0 ("can: dev: add CAN interface termination API") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Add missing attribute type validation for IEEE802154_ATTR_DEV_TYPE
to the netlink policy.
Fixes: 90c049b2c6ae ("ieee802154: interface type to be added") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Add missing attribute validation for several u8 types.
Fixes: 2c21d11518b6 ("net: add NL802154 interface for configuration of 802.15.4 devices") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Fixes: e7030878fc84 ("fib: Add fib rule match on tunnel id") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Fixes: d752a4986532 ("net: memcg: late association of sock to memcg") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Shakeel Butt <shakeelb@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If a TCP socket is allocated in IRQ context or cloned from unassociated
(i.e. not associated to a memcg) in IRQ context then it will remain
unassociated for its whole life. Almost half of the TCPs created on the
system are created in IRQ context, so, memory used by such sockets will
not be accounted by the memcg.
This issue is more widespread in cgroup v1 where network memory
accounting is opt-in but it can happen in cgroup v2 if the source socket
for the cloning was created in root memcg.
To fix the issue, just do the association of the sockets at the accept()
time in the process context and then force charge the memory buffer
already used and reserved by the socket.
Signed-off-by: Shakeel Butt <shakeelb@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We are testing network memory accounting in our setup and noticed
inconsistent network memory usage and often unrelated cgroups network
usage correlates with testing workload. On further inspection, it
seems like mem_cgroup_sk_alloc() and cgroup_sk_alloc() are broken in
irq context specially for cgroup v1.
mem_cgroup_sk_alloc() and cgroup_sk_alloc() can be called in irq context
and kind of assumes that this can only happen from sk_clone_lock()
and the source sock object has already associated cgroup. However in
cgroup v1, where network memory accounting is opt-in, the source sock
can be unassociated with any cgroup and the new cloned sock can get
associated with unrelated interrupted cgroup.
Cgroup v2 can also suffer if the source sock object was created by
process in the root cgroup or if sk_alloc() is called in irq context.
The fix is to just do nothing in interrupt.
WARNING: Please note that about half of the TCP sockets are allocated
from the IRQ context, so, memory used by such sockets will not be
accouted by the memcg.
The stack trace of mem_cgroup_sk_alloc() from IRQ-context:
MTU changes may affect the number of IRQs so we must call
bnxt_close_nic()/bnxt_open_nic() with the irq_re_init parameter
set to true. The reason is that a larger MTU may require
aggregation rings not needed with smaller MTU. We may not be
able to allocate the required number of aggregation rings and
so we reduce the number of channels which will change the number
of IRQs. Without this patch, it may crash eventually in
pci_disable_msix() when the IRQs are not properly unwound.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
It's a resource, not a parameter, so we can't copy it into the new
channel's TX queues, otherwise aliasing will lead to resource-
management bugs if the channel is subsequently torn down without
being initialised.
Before the Fixes:-tagged commit there was a similar bug with
tsoh_page, but I'm not sure it's worth doing another fix for such
old kernels.
Fixes: e9117e5099ea ("sfc: Firmware-Assisted TSO version 2") Suggested-by: Derek Shute <Derek.Shute@stratus.com> Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In one error case, tpacket_rcv drops packets after incrementing the
ring producer index.
If this happens, it does not update tp_status to TP_STATUS_USER and
thus the reader is stalled for an iteration of the ring, causing out
of order arrival.
The only such error path is when virtio_net_hdr_from_skb fails due
to encountering an unknown GSO type.
Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This is similar to commit 674d9de02aa7 ("NFC: Fix possible memory
corruption when handling SHDLC I-Frame commands") and commit d7ee81ad09f0
("NFC: nci: Add some bounds checking in nci_hci_cmd_received()") which
added range checks on "pipe".
The "pipe" variable comes skb->data[0] in nfc_hci_msg_rx_work().
It's in the 0-255 range. We're using it as the array index into the
hdev->pipes[] array which has NFC_HCI_MAX_PIPES (128) members.
Fixes: 118278f20aa8 ("NFC: hci: Add pipes table to reference them with a tuple {gate, host}") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Userspace might send a batch that is composed of several netlink
messages. The netlink_ack() function must use the pointer to the netlink
header as base to calculate the bad attribute offset.
Fixes: 2d4bc93368f5 ("netlink: extended ACK reporting") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit e18b353f102e ("ipvlan: add cond_resched_rcu() while
processing muticast backlog") added a cond_resched_rcu() in a loop
using rcu protection to iterate over slaves.
This is breaking rcu rules, so lets instead use cond_resched()
at a point we can reschedule
Fixes: e18b353f102e ("ipvlan: add cond_resched_rcu() while processing muticast backlog") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If there are substantial number of slaves created as simulated by
Syzbot, the backlog processing could take much longer and result
into the issue found in the Syzbot report.
Rafał found an issue that for non-Ethernet interface, if we down and up
frequently, the memory will be consumed slowly.
The reason is we add allnodes/allrouters addressed in multicast list in
ipv6_add_dev(). When link down, we call ipv6_mc_down(), store all multicast
addresses via mld_add_delrec(). But when link up, we don't call ipv6_mc_up()
for non-Ethernet interface to remove the addresses. This makes idev->mc_tomb
getting bigger and bigger. The call stack looks like:
After investigating, I can't found a rule to disable multicast on
non-Ethernet interface. In RFC2460, the link could be Ethernet, PPP, ATM,
tunnels, etc. In IPv4, it doesn't check the dev type when calls ip_mc_up()
in inetdev_event(). Even for IPv6, we don't check the dev type and call
ipv6_add_dev(), ipv6_dev_mc_inc() after register device.
So I think it's OK to fix this memory consumer by calling ipv6_mc_up() for
non-Ethernet interface.
v2: Also check IFF_MULTICAST flag to make sure the interface supports
multicast
Reported-by: Rafał Miłecki <zajec5@gmail.com> Tested-by: Rafał Miłecki <zajec5@gmail.com> Fixes: 74235a25c673 ("[IPV6] addrconf: Fix IPv6 on tuntap tunnels") Fixes: 1666d49e1d41 ("mld: do not remove mld souce list info when set link down") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Fixes: 95f5c64c3c13 ("gre: Move utility functions to common headers") Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In our production environment we have faced with problem that updating
classid in cgroup with heavy tasks cause long freeze of the file tables
in this tasks. By heavy tasks we understand tasks with many threads and
opened sockets (e.g. balancers). This freeze leads to an increase number
of client timeouts.
This patch implements following logic to fix this issue:
аfter iterating 1000 file descriptors file table lock will be released
thus providing a time gap for socket creation/deletion.
Now update is non atomic and socket may be skipped using calls:
dup2(oldfd, newfd);
close(oldfd);
But this case is not typical. Moreover before this patch skip is possible
too by hiding socket fd in unix socket buffer.
New sockets will be allocated with updated classid because cgroup state
is updated before start of the file descriptors iteration.
So in common cases this patch has no side effects.
Signed-off-by: Dmitry Yakunin <zeil@yandex-team.ru> Reviewed-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
It is currently possible for a PHY device to be suspended as part of a
network device driver's suspend call while it is still being attached to
that net_device, either via phy_suspend() or implicitly via phy_stop().
Later on, when the MDIO bus controller get suspended, we would attempt
to suspend again the PHY because it is still attached to a network
device.
This is both a waste of time and creates an opportunity for improper
clock/power management bugs to creep in.
Fixes: 803dd9c77ac3 ("net: phy: avoid suspending twice a PHY") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
ef1b5bf506b1 ("net: phy: Fix not to call phy_resume() if PHY is not attached") 8c85f4b81296 ("net: phy: micrel: add toggling phy reset if PHY is not attached")
Andrew Lunn informs me that there are alternative efforts
underway to fix this more properly.
Signed-off-by: David S. Miller <davem@davemloft.net>
[just take the ef1b5bf506b1 revert - gregkh] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Disabling the SATA drive interface cause kernel panic. When the drive
Interface is disabled, device should be deregistered after aborting all
pending I/Os. Also changed the port recovery timeout to 10000 ms for
PM8006 controller.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com> Signed-off-by: Viswas G <Viswas.G@microchip.com> Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The mixed mode runtime wrappers are fragile when it comes to how the
memory referred to by its pointer arguments are laid out in memory, due
to the fact that it translates these addresses to physical addresses that
the runtime services can dereference when running in 1:1 mode. Since
vmalloc'ed pages (including the vmap'ed stack) are not contiguous in the
physical address space, this scheme only works if the referenced memory
objects do not cross page boundaries.
Currently, the mixed mode runtime service wrappers require that all by-ref
arguments that live in the vmalloc space have a size that is a power of 2,
and are aligned to that same value. While this is a sensible way to
construct an object that is guaranteed not to cross a page boundary, it is
overly strict when it comes to checking whether a given object violates
this requirement, as we can simply take the physical address of the first
and the last byte, and verify that they point into the same physical page.
When this check fails, we emit a WARN(), but then simply proceed with the
call, which could cause data corruption if the next physical page belongs
to a mapping that is entirely unrelated.
Given that with vmap'ed stacks, this condition is much more likely to
trigger, let's relax the condition a bit, but fail the runtime service
call if it does trigger.
Hans reports that his mixed mode systems running v5.6-rc1 kernels hit
the WARN_ON() in virt_to_phys_or_null_size(), caused by the fact that
efi_guid_t objects on the vmap'ed stack happen to be misaligned with
respect to their sizes. As a quick (i.e., backportable) fix, copy GUID
pointer arguments to the local stack into a buffer that is naturally
aligned to its size, so that it is guaranteed to cover only one
physical page.
Note that on x86, we cannot rely on the stack pointer being aligned
the way the compiler expects, so we need to allocate an 8-byte aligned
buffer of sufficient size, and copy the GUID into that buffer at an
offset that is aligned to 16 bytes.
Fixes: f6697df36bdf0bf7 ("x86/efi: Prevent mixed mode boot corruption with CONFIG_VMAP_STACK=y") Reported-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Tested-by: Hans de Goede <hdegoede@redhat.com> Cc: linux-efi@vger.kernel.org Cc: Ingo Molnar <mingo@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20200221084849.26878-2-ardb@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The Gigabyte X570 Aorus Master motherboard with ALC1220 codec
requires a similar workaround for Clevo laptops to enforce the
DAC/mixer connection path. Set up a quirk entry for that.
For the same reason as commit 19514fc665ff ("arm, kbuild: make "make
install" not depend on vmlinux"), the install targets should never
trigger the rebuild of the kernel.
The variable, CONFIGURE, is not set by anyone. Remove it as well.
We need to ensure that the default VID is untagged otherwise the switch
will be sending tagged frames and the results can be problematic. This
is especially true with b53 switches that use VID 0 as their default
VLAN since VID 0 has a special meaning.
Fixes: fea83353177a ("net: dsa: b53: Fix default VLAN ID") Fixes: 061f6a505ac3 ("net: dsa: Add ndo_vlan_rx_{add, kill}_vid implementation") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Add a flag to DMA memory allocation to silence a warning.
This driver allocates DMA memory for IO frames. This allocation may exceed
MAX_ORDER pages for few megaraid_sas controllers (controllers with very
high queue depth). Consequently, the driver has logic to keep reducing the
controller queue depth until the DMA memory allocation succeeds.
On impacted megaraid_sas controllers there would be multiple DMA allocation
failures until driver settled on an allocation that fit. These failed DMA
allocation requests caused stack traces in system logs. These were not
harmful and this patch silences those warnings/stack traces.
[mkp: clarified commit desc]
Link: https://lore.kernel.org/r/20200204152413.7107-1-thenzl@redhat.com Signed-off-by: Tomas Henzl <thenzl@redhat.com> Acked-by: Sumit Saxena <sumit.saxena@broadcom.com> Reviewed-by: Lee Duncan <lduncan@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
At the time the brcmstb_thermal driver and its binding were merged, the
DT binding did not make the coefficients properties a mandatory one,
therefore all users of the brcmstb_thermal driver out there have a non
functional implementation with zero coefficients. Even if these
properties were provided, the formula used for computation is incorrect.
The coefficients are entirely process specific (right now, only 28nm is
supported) and not board or SoC specific, it is therefore appropriate to
hard code them in the driver given the compatibility string we are
probed with which has to be updated whenever a new process is
introduced.
We remove the existing coefficients definition since subsequent patches
are going to add support for a new process and will introduce new
coefficients as well.
Remove a bogus clearing of apf.msr_val from kvm_arch_vcpu_destroy().
apf.msr_val is only set to a non-zero value by kvm_pv_enable_async_pf(),
which is only reachable by kvm_set_msr_common(), i.e. by writing
MSR_KVM_ASYNC_PF_EN. KVM does not autonomously write said MSR, i.e.
can only be written via KVM_SET_MSRS or KVM_RUN. Since KVM_SET_MSRS and
KVM_RUN are vcpu ioctls, they require a valid vcpu file descriptor.
kvm_arch_vcpu_destroy() is only called if KVM_CREATE_VCPU fails, and KVM
declares KVM_CREATE_VCPU successful once the vcpu fd is installed and
thus visible to userspace. Ergo, apf.msr_val cannot be non-zero when
kvm_arch_vcpu_destroy() is called.
Fixes: 344d9588a9df0 ("KVM: Add PV MSR to enable asynchronous page faults delivery.") Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
x86 does not load its MMU until KVM_RUN, which cannot be invoked until
after vCPU creation succeeds. Given that kvm_arch_vcpu_destroy() is
called if and only if vCPU creation fails, it is impossible for the MMU
to be loaded.
Note, the bogus kvm_mmu_unload() call was added during an unrelated
refactoring of vCPU allocation, i.e. was presumably added as an
opportunstic "fix" for a perceived leak.
Fixes: fb3f0f51d92d1 ("KVM: Dynamically allocate vcpus") Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Removing a cfs_rq from rq->leaf_cfs_rq_list can break the parent/child
ordering of the list when it will be added back. In order to remove an
empty and fully decayed cfs_rq, we must remove its children too, so they
will be added back in the right order next time.
With a normal decay of PELT, a parent will be empty and fully decayed
if all children are empty and fully decayed too. In such a case, we just
have to ensure that the whole branch will be added when a new task is
enqueued. This is default behavior since :
commit f6783319737f ("sched/fair: Fix insertion in rq->leaf_cfs_rq_list")
In case of throttling, the PELT of throttled cfs_rq will not be updated
whereas the parent will. This breaks the assumption made above unless we
remove the children of a cfs_rq that is throttled. Then, they will be
added back when unthrottled and a sched_entity will be enqueued.
As throttled cfs_rq are now removed from the list, we can remove the
associated test in update_blocked_averages().
When getting or setting VNICC parameters, the error code EOPNOTSUPP
should have precedence over EBUSY.
EBUSY is used because vnicc feature and bridgeport feature are mutually
exclusive, which is a temporary condition.
Whereas EOPNOTSUPP indicates that the HW does not support all or parts of
the vnicc feature.
This issue causes the vnicc sysfs params to show 'blocked by bridgeport'
for HW that does not support VNICC at all.
Fixes: caa1f0b10d18 ("s390/qeth: add VNICC enable/disable support") Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When netvsc_attach() is called by operations like changing MTU, etc.,
an extra wakeup may happen while netvsc_attach() calling
rndis_filter_device_add() which sends rndis messages when queue is
stopped in netvsc_detach(). The completion message will wake up queue 0.
We can reproduce the issue by changing MTU etc., then the wake_queue
counter from "ethtool -S" will increase beyond stop_queue counter:
stop_queue: 0
wake_queue: 1
The issue causes queue wake up, and counter increment, no other ill
effects in current code. So we didn't see any network problem for now.
To fix this, initialize tx_disable to true, and set it to false when
the NIC is ready to be attached or registered.
Fixes: 7b2ee50c0cd5 ("hv_netvsc: common detach logic") Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
They are issues:
- if 'input_allocate_device()' fails and return NULL, there is no need
to free anything and 'input_free_device()' call is a no-op. It can
be axed.
- 'ret' is known to be 0 at this point, so we must set it to a
meaningful value before returning
Removing attach_adapter from this driver caused a regression for at
least some machines. Those machines had the sensors described in their
DT, too, so they didn't need manual creation of the sensor devices. The
old code worked, though, because manual creation came first. Creation of
DT devices then failed later and caused error logs, but the sensors
worked nonetheless because of the manually created devices.
When removing attach_adaper, manual creation now comes later and loses
the race. The sensor devices were already registered via DT, yet with
another binding, so the driver could not be bound to it.
This fix refactors the code to remove the race and only manually creates
devices if there are no DT nodes present. Also, the DT binding is updated
to match both, the DT and manually created devices. Because we don't
know which device creation will be used at runtime, the code to start
the kthread is moved to do_probe() which will be called by both methods.
Fixes: 3e7bed52719d ("macintosh: therm_windtunnel: drop using attach_adapter") Link: https://bugzilla.kernel.org/show_bug.cgi?id=201723 Reported-by: Erhard Furtner <erhard_f@mailbox.org> Tested-by: Erhard Furtner <erhard_f@mailbox.org> Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc) Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org # v4.19+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The internal statistic counters for the total number of
requests processed per card and per queue used integers. So they do
wrap after a rather huge amount of crypto requests processed. This
patch introduces uint64 counters which should hold much longer but
still may wrap. The sysfs attributes request_count for card and queue
also used only %ld and now display the counter value with %llu.
This is not a security relevant fix. The int overflow which happened
is not in any way exploitable as a security breach.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
rxrpc_rcu_destroy_call(), which is called as an RCU callback to clean up a
put call, calls rxrpc_put_connection() which, deep in its bowels, takes a
number of spinlocks in a non-BH-safe way, including rxrpc_conn_id_lock and
local->client_conns_lock. RCU callbacks, however, are normally called from
softirq context, which can cause lockdep to notice the locking
inconsistency.
To get lockdep to detect this, it's necessary to have the connection
cleaned up on the put at the end of the last of its calls, though normally
the clean up is deferred. This can be induced, however, by starting a call
on an AF_RXRPC socket and then closing the socket without reading the
reply.
Fix this by having rxrpc_rcu_destroy_call() punt the destruction to a
workqueue if in softirq-mode and defer the destruction to process context.
Note that another way to fix this could be to add a bunch of bh-disable
annotations to the spinlocks concerned - and there might be more than just
those two - but that means spending more time with BHs disabled.
Note also that some of these places were covered by bh-disable spinlocks
belonging to the rxrpc_transport object, but these got removed without the
_bh annotation being retained on the next lock in.
Fixes: 999b69f89241 ("rxrpc: Kill the client connection bundle concept") Reported-by: syzbot+d82f3ac8d87e7ccbb2c9@syzkaller.appspotmail.com Reported-by: syzbot+3f1fd6b8cbf8702d134e@syzkaller.appspotmail.com Signed-off-by: David Howells <dhowells@redhat.com>
cc: Hillf Danton <hdanton@sina.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
While running my error injection script I hit a panic when we tried to
clean up the fs_root when freeing the fs_root. This is because
fs_info->fs_root == PTR_ERR(-EIO), which isn't great. Fix this by
setting fs_info->fs_root = NULL; if we fail to read the root.
CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This was noticed when printing debugfs for MSIs on my ARM64 server. The
new dstate IRQD_MSI_NOMASK_QUIRK came out surprisingly while it should only
be the x86 stuff for the time being...
The new MSI quirk flag uses the same bit as IRQ_DOMAIN_NAME_ALLOCATED which
is oddly defined as bit 6 for no good reason.
added support for access to the free-running counter via 'perf -e
msr/irperf/', but when exercised, it always returns a 0 count:
BEFORE:
$ perf stat -e instructions,msr/irperf/ true
Performance counter stats for 'true':
624,833 instructions
0 msr/irperf/
Simply set its enable bit - HWCR bit 30 - to make it start counting.
Enablement is restricted to all machines advertising IRPERF capability,
except those susceptible to an erratum that makes the IRPERF return
bad values.
That erratum occurs in Family 17h models 00-1fh [1], but not in F17h
models 20h and above [2].
AFTER (on a family 17h model 31h machine):
$ perf stat -e instructions,msr/irperf/ true
Performance counter stats for 'true':
621,690 instructions
622,490 msr/irperf/
[1] Revision Guide for AMD Family 17h Models 00h-0Fh Processors
[2] Revision Guide for AMD Family 17h Models 30h-3Fh Processors
The revision guides are available from the bugzilla Link below.
I found a NULL pointer dereference in ocfs2_block_group_clear_bits().
The running environment:
kernel version: 4.19
A cluster with two nodes, 5 luns mounted on two nodes, and do some
file operations like dd/fallocate/truncate/rm on every lun with storage
network disconnection.
The fallocate operation on dm-23-45 caused an null pointer dereference.
My analysis process as follows:
ocfs2_fallocate
__ocfs2_change_file_space
ocfs2_allocate_extents
ocfs2_extend_allocation
ocfs2_add_inode_data
ocfs2_add_clusters_in_btree
ocfs2_insert_extent
ocfs2_do_insert_extent
ocfs2_rotate_tree_right
ocfs2_extend_rotate_transaction
ocfs2_extend_trans
jbd2_journal_restart
jbd2__journal_restart
/* handle->h_transaction is NULL,
* is_handle_aborted(handle) is true
*/
handle->h_transaction = NULL;
start_this_handle
return -EROFS;
ocfs2_free_clusters
_ocfs2_free_clusters
_ocfs2_free_suballoc_bits
ocfs2_block_group_clear_bits
ocfs2_journal_access_gd
__ocfs2_journal_access
jbd2_journal_get_undo_access
/* I think jbd2_write_access_granted() will
* return true, because do_get_write_access()
* will return -EROFS.
*/
if (jbd2_write_access_granted(...)) return 0;
do_get_write_access
/* handle->h_transaction is NULL, it will
* return -EROFS here, so do_get_write_access()
* was not called.
*/
if (is_handle_aborted(handle)) return -EROFS;
/* bh2jh(group_bh) is NULL, caused NULL
pointer dereference */
undo_bg = (struct ocfs2_group_desc *)
bh2jh(group_bh)->b_committed_data;
If handle->h_transaction == NULL, then jbd2_write_access_granted()
does not really guarantee that journal_head will stay around,
not even speaking of its b_committed_data. The bh2jh(group_bh)
can be removed after ocfs2_journal_access_gd() and before call
"bh2jh(group_bh)->b_committed_data". So, we should move
is_handle_aborted() check from do_get_write_access() into
jbd2_journal_get_undo_access() and jbd2_journal_get_write_access()
before the call to jbd2_write_access_granted().
Link: https://lore.kernel.org/r/f72a623f-b3f1-381a-d91d-d22a1c83a336@huawei.com Signed-off-by: Yan Wang <wangyan122@huawei.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Jun Piao <piaojun@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
After a treclaim, we expect to be in non-transactional state. If we
don't clear the current thread's MSR[TS] before we get preempted, then
tm_recheckpoint_new_task() will recheckpoint and we get rescheduled in
suspended transaction state.
When handling a signal caught in transactional state,
handle_rt_signal64() calls get_tm_stackpointer() that treclaims the
transaction using tm_reclaim_current() but without clearing the
thread's MSR[TS]. This can cause the TM Bad Thing exception below if
later we pagefault and get preempted trying to access the user's
sigframe, using __put_user(). Afterwards, when we are rescheduled back
into do_page_fault() (but now in suspended state since the thread's
MSR[TS] was not cleared), upon executing 'rfid' after completion of
the page fault handling, the exception is raised because a transition
from suspended to non-transactional state is invalid.
The simplified sequence of events that triggers the above exception is:
... # userspace in NON-TRANSACTIONAL state
tbegin # userspace in TRANSACTIONAL state
signal delivery # kernelspace in SUSPENDED state
handle_rt_signal64()
get_tm_stackpointer()
treclaim # kernelspace in NON-TRANSACTIONAL state
__put_user()
page fault happens. We will never get back here because of the TM Bad Thing exception.
page fault handling kicks in and we voluntarily preempt ourselves
do_page_fault()
__schedule()
__switch_to(other_task)
our task is rescheduled and we recheckpoint because the thread's MSR[TS] was not cleared
__switch_to(our_task)
switch_to_tm()
tm_recheckpoint_new_task()
trechkpt # kernelspace in SUSPENDED state
The page fault handling resumes, but now we are in suspended transaction state
do_page_fault() completes
rfid <----- trying to get back where the page fault happened (we were non-transactional back then)
TM Bad Thing # illegal transition from suspended to non-transactional
This patch fixes that issue by clearing the current thread's MSR[TS]
just after treclaim in get_tm_stackpointer() so that we stay in
non-transactional state in case we are preempted. In order to make
treclaim and clearing the thread's MSR[TS] atomic from a preemption
perspective when CONFIG_PREEMPT is set, preempt_disable/enable() is
used. It's also necessary to save the previous value of the thread's
MSR before get_tm_stackpointer() is called so that it can be exposed
to the signal handler later in setup_tm_sigcontexts() to inform the
userspace MSR at the moment of the signal delivery.
Found with tm-signal-context-force-tm kernel selftest.
Fixes: 2b0a576d15e0 ("powerpc: Add new transactional memory state to the signal context") Cc: stable@vger.kernel.org # v3.9 Signed-off-by: Gustavo Luiz Duarte <gustavold@linux.ibm.com> Acked-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200211033831.11165-1-gustavold@linux.ibm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This device has a broken vendor-specific altsetting for interface 1,
where endpoint 0x85 is declared as an isochronous endpoint despite being
used by interface 2 for audio capture.
Since commit 3e4f8e21c4f2 ("USB: core: fix check for duplicate
endpoints") USB core ignores any duplicate endpoints found during
descriptor parsing, but in this case we need to ignore the first
instance in order to avoid breaking the audio capture interface.
Fixes: 3e4f8e21c4f2 ("USB: core: fix check for duplicate endpoints") Cc: stable <stable@vger.kernel.org> Reported-by: edes <edes@gmx.net> Tested-by: edes <edes@gmx.net> Link: https://lore.kernel.org/r/20200201105829.5682c887@acme7.acmenet Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20200203153830.26394-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Add a new device quirk that can be used to blacklist endpoints.
Since commit 3e4f8e21c4f2 ("USB: core: fix check for duplicate
endpoints") USB core ignores any duplicate endpoints found during
descriptor parsing.
In order to handle devices where the first interfaces with duplicate
endpoints are the ones that should have their endpoints ignored, we need
to add a blacklist.
Tested-by: edes <edes@gmx.net> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20200203153830.26394-2-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In case of ABI version mismatch, _manifest needs to be freed as
it is just a copy of the original topology manifest. However, if
a driver manifest handler is defined, that would get executed and
the cleanup is never reached. Fix that by getting the return status
of manifest() instead of returning directly.
Fixes: 583958fa2e52 ("ASoC: topology: Make manifest backward compatible from ABI v4") Signed-off-by: Dragos Tarcatu <dragos_tarcatu@mentor.com> Link: https://lore.kernel.org/r/20200207185325.22320-3-dragos_tarcatu@mentor.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
At xhci removal the USB3 hcd (shared_hcd) is removed before the primary
USB2 hcd. Interrupts for port status changes may still occur for USB3
ports after the shared_hcd is freed, causing NULL pointer dereference.
Check if xhci->shared_hcd is still valid before handing USB3 port events
Cc: <stable@vger.kernel.org> Reported-by: Peter Chen <peter.chen@nxp.com> Tested-by: Jack Pham <jackp@codeaurora.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Cc: Macpaul Lin <macpaul.lin@mediatek.com>
[redone for 4.14.y based on Mathias's comments] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If we need to perform synchronous I/O in dm_integrity_map_continue(),
we must make sure that we are not in the map function - in order to
avoid the deadlock due to bio queuing in generic_make_request. To
avoid the deadlock, we offload the request to metadata_wq.
However, metadata_wq also processes metadata updates for write requests.
If there are too many requests that get offloaded to metadata_wq at the
beginning of dm_integrity_map_continue, the workqueue metadata_wq
becomes clogged and the system is incapable of processing any metadata
updates.
This causes a deadlock because all the requests that need to do metadata
updates wait for metadata_wq to proceed and metadata_wq waits inside
wait_and_add_new_range until some existing request releases its range
lock (which doesn't happen because the range lock is released after
metadata update).
In order to fix the deadlock, we create a new workqueue offload_wq and
offload requests to it - so that processing of offload_wq is independent
from processing of metadata_wq.
PowerVM systems running compatibility mode on a few Power8 revisions are
still vulnerable to the hardware defect that loses PMU exceptions arriving
prior to a context switch.
The software fix for this issue is enabled through the CPU_FTR_PMAO_BUG
cpu_feature bit, nevertheless this bit also needs to be set for PowerVM
compatibility mode systems.
Fixes: 68f2f0d431d9ea4 ("powerpc: Add a cpu feature CPU_FTR_PMAO_BUG") Signed-off-by: Desnes A. Nunes do Rosario <desnesn@linux.ibm.com> Reviewed-by: Leonardo Bras <leonardo@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200227134715.9715-1-desnesn@linux.ibm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This is only called from adt7462_update_device(). The caller expects it
to return zero on error. I fixed a similar issue earlier in commit a4bf06d58f21 ("hwmon: (adt7462) ADT7462_REG_VOLT_MAX() should return 0")
but I missed this one.
Fixes: c0b4e3ab0c76 ("adt7462: new hwmon driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Link: https://lore.kernel.org/r/20200303101608.kqjwfcazu2ylhi2a@kili.mountain Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This function is not only needed by the platform suspend code, but is also
reused as the CPU resume function when the ARM cores can be powered down
completely in deep idle, which is the case on i.MX6SX and i.MX6UL(L).
Providing the static inline stub whenever CONFIG_SUSPEND is disabled means
that those platforms will hang on resume from cpuidle if suspend is disabled.
So there are two problems:
- The static inline stub masks the linker error
- The function is not available where needed
Fix both by just building the function unconditionally, when
CONFIG_SOC_IMX6 is enabled. The actual code is three instructions long,
so it's arguably ok to just leave it in for all i.MX6 kernel configurations.
Fixes: 05136f0897b5 ("ARM: imx: support arm power off in cpuidle for i.mx6sx") Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Signed-off-by: Rouven Czerwinski <r.czerwinski@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The packet handling function, specifically the iteration of the qp list
for mad packet processing misses locking RCU before running through the
list. Not only is this incorrect, but the list_for_each_entry_rcu() call
can not be called with a conditional check for lock dependency. Remedy
this by invoking the rcu lock and unlock around the critical section.
This brings MAD packet processing in line with what is done for non-MAD
packets.
Fixes: 7724105686e7 ("IB/hfi1: add driver files") Link: https://lore.kernel.org/r/20200225195445.140896.41873.stgit@awfm-01.aw.intel.com Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The algorithm pre-allocates a cm_id since allocation cannot be done while
holding the cm.lock spinlock, however it doesn't free it on one error
path, leading to a memory leak.
Fixes: 067b171b8679 ("IB/cm: Share listening CM IDs") Link: https://lore.kernel.org/r/20200221152023.GA8680@ziepe.ca Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The dealloc_work_entries() function must update the work_free_list pointer
while freeing its entries, since potentially called again on same list. A
second iteration of the work list caused system crash. This happens, if
work allocation fails during cma_iw_listen() and free_cm_id() tries to
free the list again during cleanup.
Fixes: 922a8e9fb2e0 ("RDMA: iWARP Connection Manager.") Link: https://lore.kernel.org/r/20200302181614.17042-1-bmt@zurich.ibm.com Reported-by: syzbot+cb0c054eabfba4342146@syzkaller.appspotmail.com Signed-off-by: Bernard Metzler <bmt@zurich.ibm.com> Reviewed-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
commit c2caa4da46a4 ("ASoC: Fix widget powerdown on shutdown") added a
set of the power state during snd_soc_dapm_shutdown to ensure the
widgets powered off. However, when commit 39eb5fd13dff
("ASoC: dapm: Delay w->power update until the changes are written")
added the new_power member of the widget structure, to differentiate
between the current power state and the target power state, it did not
update the shutdown to use the new_power member.
As new_power has not updated it will be left in the state set by the
last DAPM sequence, ie. 1 for active widgets. So as the DAPM sequence
for the shutdown proceeds it will turn the widgets on (despite them
already being on) rather than turning them off.
Fixes: 39eb5fd13dff ("ASoC: dapm: Delay w->power update until the changes are written") Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20200228153145.21013-1-ckeepax@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
dpcm_show_state() invokes multiple snprintf() calls to concatenate
formatted strings on the fixed size buffer. The usage of snprintf()
is supposed for avoiding the buffer overflow, but it doesn't work as
expected because snprintf() doesn't return the actual output size but
the size to be written.
Fix this bug by replacing all snprintf() calls with scnprintf()
calls.
Fixes: f86dcef87b77 ("ASoC: dpcm: Add debugFS support for DPCM") Signed-off-by: Takashi Iwai <tiwai@suse.de> Acked-by: Cezary Rojewski <cezary.rojewski@intel.com> Link: https://lore.kernel.org/r/20200218111737.14193-4-tiwai@suse.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The debugfs output of intel skl driver writes strings with multiple
snprintf() calls with the fixed size. This was supposed to avoid the
buffer overflow but actually it still would, because snprintf()
returns the expected size to be output, not the actual output size.
Fix it by replacing snprintf() calls with scnprintf().
Fixes: d14700a01f91 ("ASoC: Intel: Skylake: Debugfs facility to dump module config") Signed-off-by: Takashi Iwai <tiwai@suse.de> Acked-by: Cezary Rojewski <cezary.rojewski@intel.com> Link: https://lore.kernel.org/r/20200218111737.14193-3-tiwai@suse.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
skl_print_pins() loops over all given pins but it overwrites the text
at the very same position while increasing the returned length.
Fix this to show the all pin contents properly.
Fixes: d14700a01f91 ("ASoC: Intel: Skylake: Debugfs facility to dump module config") Signed-off-by: Takashi Iwai <tiwai@suse.de> Acked-by: Cezary Rojewski <cezary.rojewski@intel.com> Link: https://lore.kernel.org/r/20200218111737.14193-2-tiwai@suse.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If soc_tplg_link_config() fails, _link needs to be freed in case of
topology ABI version mismatch. However the current code is returning
directly and ends up leaking memory in this case.
This patch fixes that.
Fixes: 593d9e52f9bb ("ASoC: topology: Add support to configure existing physical DAI links") Signed-off-by: Dragos Tarcatu <dragos_tarcatu@mentor.com> Link: https://lore.kernel.org/r/20200207185325.22320-2-dragos_tarcatu@mentor.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The difference between "fsl,etsec2-mdio" and "gianfar" has to do with
the .get_tbipa function, which calculates the address of the TBIPA
register automatically, if not explicitly specified. [ see
drivers/net/ethernet/freescale/fsl_pq_mdio.c ]. On LS1021A, the TBIPA
register is at offset 0x30 within the port register block, which is what
the "gianfar" method of calculating addresses actually does.
Luckily, the bad "compatible" is inconsequential for ls1021a.dtsi,
because the TBIPA register is explicitly specified via the second "reg"
(<0x0 0x2d10030 0x0 0x4>), so the "get_tbipa" function is dead code.
Nonetheless it's good to restore it to its correct value.
The crash can be reproduced by running the lvm2 testsuite test
lvconvert-thin-external-cache.sh for several minutes, e.g.:
while :; do make check T=shell/lvconvert-thin-external-cache.sh; done
The crash happens in this call chain:
do_waker -> policy_tick -> smq_tick -> end_hotspot_period -> clear_bitset
-> memset -> __memset -- which accesses an invalid pointer in the vmalloc
area.
The work entry on the workqueue is executed even after the bitmap was
freed. The problem is that cancel_delayed_work doesn't wait for the
running work item to finish, so the work item can continue running and
re-submitting itself even after cache_postsuspend. In order to make sure
that the work item won't be running, we must use cancel_delayed_work_sync.
Also, change flush_workqueue to drain_workqueue, so that if some work item
submits itself or another work item, we are properly waiting for both of
them.
The interrupt handler puts a half-completed DMA descriptor on a free list
and then schedules tasklet to process bottom half of the descriptor that
executes client's callback, this creates possibility to pick up the busy
descriptor from the free list. Thus, let's disallow descriptor's re-use
until it is fully processed.
I was doing some experiments with I2C and noticed that Tegra APB DMA
driver crashes sometime after I2C DMA transfer termination. The crash
happens because tegra_dma_terminate_all() bails out immediately if pending
list is empty, and thus, it doesn't release the half-completed descriptors
which are getting re-used before ISR tasklet kicks-in.
tegra-i2c 7000c400.i2c: DMA transfer timeout
elants_i2c 0-0010: elants_i2c_irq: failed to read data: -110
------------[ cut here ]------------
WARNING: CPU: 0 PID: 142 at lib/list_debug.c:45 __list_del_entry_valid+0x45/0xac
list_del corruption, ddbaac44->next is LIST_POISON1 (00000100)
Modules linked in:
CPU: 0 PID: 142 Comm: kworker/0:2 Not tainted 5.5.0-rc2-next-20191220-00175-gc3605715758d-dirty #538
Hardware name: NVIDIA Tegra SoC (Flattened Device Tree)
Workqueue: events_freezable_power_ thermal_zone_device_check
[<c010e5c5>] (unwind_backtrace) from [<c010a1c5>] (show_stack+0x11/0x14)
[<c010a1c5>] (show_stack) from [<c0973925>] (dump_stack+0x85/0x94)
[<c0973925>] (dump_stack) from [<c011f529>] (__warn+0xc1/0xc4)
[<c011f529>] (__warn) from [<c011f7e9>] (warn_slowpath_fmt+0x61/0x78)
[<c011f7e9>] (warn_slowpath_fmt) from [<c042497d>] (__list_del_entry_valid+0x45/0xac)
[<c042497d>] (__list_del_entry_valid) from [<c047a87f>] (tegra_dma_tasklet+0x5b/0x154)
[<c047a87f>] (tegra_dma_tasklet) from [<c0124799>] (tasklet_action_common.constprop.0+0x41/0x7c)
[<c0124799>] (tasklet_action_common.constprop.0) from [<c01022ab>] (__do_softirq+0xd3/0x2a8)
[<c01022ab>] (__do_softirq) from [<c0124683>] (irq_exit+0x7b/0x98)
[<c0124683>] (irq_exit) from [<c0168c19>] (__handle_domain_irq+0x45/0x80)
[<c0168c19>] (__handle_domain_irq) from [<c043e429>] (gic_handle_irq+0x45/0x7c)
[<c043e429>] (gic_handle_irq) from [<c0101aa5>] (__irq_svc+0x65/0x94)
Exception stack(0xde2ebb90 to 0xde2ebbd8)
Explicitly set X86_FEATURE_OSPKE via set_cpu_cap() instead of calling
get_cpu_cap() to pull the feature bit from CPUID after enabling CR4.PKE.
Invoking get_cpu_cap() effectively wipes out any {set,clear}_cpu_cap()
changes that were made between this_cpu->c_init() and setup_pku(), as
all non-synthetic feature words are reinitialized from the CPU's CPUID
values.
Blasting away capability updates manifests most visibility when running
on a VMX capable CPU, but with VMX disabled by BIOS. To indicate that
VMX is disabled, init_ia32_feat_ctl() clears X86_FEATURE_VMX, using
clear_cpu_cap() instead of setup_clear_cpu_cap() so that KVM can report
which CPU is misconfigured (KVM needs to probe every CPU anyways).
Restoring X86_FEATURE_VMX from CPUID causes KVM to think VMX is enabled,
ultimately leading to an unexpected #GP when KVM attempts to do VMXON.
Arguably, init_ia32_feat_ctl() should use setup_clear_cpu_cap() and let
KVM figure out a different way to report the misconfigured CPU, but VMX
is not the only feature bit that is affected, i.e. there is precedent
that tweaking feature bits via {set,clear}_cpu_cap() after ->c_init()
is expected to work. Most notably, x86_init_rdrand()'s clearing of
X86_FEATURE_RDRAND when RDRAND malfunctions is also overwritten.
Fixes: 0697694564c8 ("x86/mm/pkeys: Actually enable Memory Protection Keys in the CPU") Reported-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Acked-by: Dave Hansen <dave.hansen@linux.intel.com> Tested-by: Jacob Keller <jacob.e.keller@intel.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20200226231615.13664-1-sean.j.christopherson@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>