Xin Long [Thu, 21 Nov 2019 10:08:38 +0000 (18:08 +0800)]
net: remove the unnecessary strict_start_type in some policies
ct_policy and mpls_policy are parsed with nla_parse_nested(), which
does NL_VALIDATE_STRICT validation, strict_start_type is not needed
to set as it is actually trying to make some attributes parsed with
NL_VALIDATE_STRICT.
This patch is to remove it, and do the same on rtm_nh_policy which
is parsed by nlmsg_parse().
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Thu, 21 Nov 2019 10:03:29 +0000 (18:03 +0800)]
net: sched: allow flower to match erspan options
This patch is to allow matching options in erspan.
The options can be described in the form:
VER:INDEX:DIR:HWID/VER:INDEX_MASK:DIR_MASK:HWID_MASK.
When ver is set to 1, index will be applied while dir
and hwid will be ignored, and when ver is set to 2,
dir and hwid will be used while index will be ignored.
Different from geneve, only one option can be set. And
also, geneve options, vxlan options or erspan options
can't be set at the same time.
# ip link add name erspan1 type erspan external
# tc qdisc add dev erspan1 ingress
# tc filter add dev erspan1 protocol ip parent ffff: \
flower \
enc_src_ip 10.0.99.192 \
enc_dst_ip 10.0.99.193 \
enc_key_id 11 \
erspan_opts 1:12:0:0/1:ffff:0:0 \
ip_proto udp \
action mirred egress redirect dev eth0
v1->v2:
- improve some err msgs of extack.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Thu, 21 Nov 2019 10:03:28 +0000 (18:03 +0800)]
net: sched: allow flower to match vxlan options
This patch is to allow matching gbp option in vxlan.
The options can be described in the form GBP/GBP_MASK,
where GBP is represented as a 32bit hexadecimal value.
Different from geneve, only one option can be set. And
also, geneve options and vxlan options can't be set at
the same time.
# ip link add name vxlan0 type vxlan dstport 0 external
# tc qdisc add dev vxlan0 ingress
# tc filter add dev vxlan0 protocol ip parent ffff: \
flower \
enc_src_ip 10.0.99.192 \
enc_dst_ip 10.0.99.193 \
enc_key_id 11 \
vxlan_opts 01020304/ffffffff \
ip_proto udp \
action mirred egress redirect dev eth0
v1->v2:
- add .strict_start_type for enc_opts_policy as Jakub noticed.
- use Duplicate instead of Wrong in err msg for extack as Jakub
suggested.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Thu, 21 Nov 2019 10:03:27 +0000 (18:03 +0800)]
net: sched: add erspan option support to act_tunnel_key
This patch is to allow setting erspan options using the
act_tunnel_key action. Different from geneve options,
only one option can be set. And also, geneve options,
vxlan options or erspan options can't be set at the
same time.
Options are expressed as ver:index:dir:hwid, when ver
is set to 1, index will be applied while dir and hwid
will be ignored, and when ver is set to 2, dir and
hwid will be used while index will be ignored.
# ip link add name erspan1 type erspan external
# tc qdisc add dev eth0 ingress
# tc filter add dev eth0 protocol ip parent ffff: \
flower indev eth0 \
ip_proto udp \
action tunnel_key \
set src_ip 10.0.99.192 \
dst_ip 10.0.99.193 \
dst_port 6081 \
id 11 \
erspan_opts 1:2:0:0 \
action mirred egress redirect dev erspan1
v1->v2:
- do the validation when dst is not yet allocated as Jakub suggested.
- use Duplicate instead of Wrong in err msg for extack.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Thu, 21 Nov 2019 10:03:26 +0000 (18:03 +0800)]
net: sched: add vxlan option support to act_tunnel_key
This patch is to allow setting vxlan options using the
act_tunnel_key action. Different from geneve options,
only one option can be set. And also, geneve options
and vxlan options can't be set at the same time.
gbp is the only param for vxlan options:
# ip link add name vxlan0 type vxlan dstport 0 external
# tc qdisc add dev eth0 ingress
# tc filter add dev eth0 protocol ip parent ffff: \
flower indev eth0 \
ip_proto udp \
action tunnel_key \
set src_ip 10.0.99.192 \
dst_ip 10.0.99.193 \
dst_port 6081 \
id 11 \
vxlan_opts 01020304 \
action mirred egress redirect dev vxlan0
v1->v2:
- add .strict_start_type for enc_opts_policy as Jakub noticed.
- use Duplicate instead of Wrong in err msg for extack as Jakub
suggested.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Thu, 21 Nov 2019 09:21:46 +0000 (12:21 +0300)]
octeontx2-af: Fix uninitialized variable in debugfs
If rvu_get_blkaddr() fails, then this rvu_cgx_nix_cuml_stats() returns
zero and we write some uninitialized data into the debugfs output.
On the error paths, the use of the uninitialized "*stat" is harmless,
but it will lead to a Smatch warning (static analysis) and a UBSan
warning (runtime analysis) so we should prevent that as well.
Fixes: f967488d095e ("octeontx2-af: Add per CGX port level NIX Rx/Tx counters") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
vsock: avoid to assign transport if its initialization fails
If transport->init() fails, we can't assign the transport to the
socket, because it's not initialized correctly, and any future
calls to the transport callbacks would have an unexpected behavior.
Fixes: c0cfa2d8a788 ("vsock: add multi-transports support") Reported-and-tested-by: syzbot+e2e5c07bf353b2f79daa@syzkaller.appspotmail.com Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Reviewed-by: Jorgen Hansen <jhansen@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Wed, 20 Nov 2019 12:29:59 +0000 (12:29 +0000)]
net: sfp: soft status and control support
Add support for the soft status and control register, which allows
TX_FAULT and RX_LOS to be monitored and TX_DISABLE to be set. We
make use of this when the board does not support GPIOs for these
signals.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 21 Nov 2019 06:28:53 +0000 (22:28 -0800)]
Merge branch 'sfp-quirks'
Russell King says:
====================
Add rudimentary SFP module quirk support
The SFP module EEPROM describes the capabilities of the module, but
doesn't describe the host interface. We have a certain amount of
guess-work to work out how to configure the host - which works most
of the time.
However, there are some (such as GPON) modules which are able to
support different host interfaces, such as 1000BASE-X and 2500BASE-X.
The module will switch between each mode until it achieves link with
the host.
There is no defined way to describe this in the SFP EEPROM, so we can
only recognise the module and handle it appropriately. This series
adds the necessary recognition of the modules using a quirk system,
and tweaks the support mask to allow them to link with the host at
2500BASE-X, thereby allowing the user to achieve full line rate.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Wed, 20 Nov 2019 11:42:47 +0000 (11:42 +0000)]
net: sfp: add some quirks for GPON modules
Marc Micalizzi reports that Huawei MA5671A and Alcatel/Lucent G-010S-P
modules are capable of 2500base-X, but incorrectly report their
capabilities in the EEPROM. It seems rather common that GPON modules
mis-report.
Let's fix these modules by adding some quirks.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Wed, 20 Nov 2019 11:42:42 +0000 (11:42 +0000)]
net: sfp: add support for module quirks
Add support for applying module quirks to the list of supported
ethtool link modes.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Wed, 20 Nov 2019 08:38:08 +0000 (16:38 +0800)]
tcp: warn if offset reach the maxlen limit when using snprintf
snprintf returns the number of chars that would be written, not number
of chars that were actually written. As such, 'offs' may get larger than
'tbl.maxlen', causing the 'tbl.maxlen - offs' being < 0, and since the
parameter is size_t, it would overflow.
Since using scnprintf may hide the limit error, while the buffer is still
enough now, let's just add a WARN_ON_ONCE in case it reach the limit
in future.
v2: Use WARN_ON_ONCE as Jiri and Eric suggested.
Suggested-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
wenxu [Wed, 20 Nov 2019 02:59:39 +0000 (10:59 +0800)]
ip_gre: Make none-tun-dst gre tunnel store tunnel info as metadat_dst in recv
Currently collect_md gre tunnel will store the tunnel info(metadata_dst)
to skb_dst.
And now the non-tun-dst gre tunnel already can add tunnel header through
lwtunnel.
When received a arp_request on the non-tun-dst gre tunnel. The packet of
arp response will send through the non-tun-dst tunnel without tunnel info
which will lead the arp response packet to be dropped.
If the non-tun-dst gre tunnel also store the tunnel info as metadata_dst,
The arp response packet will set the releted tunnel info in the
iptunnel_metadata_reply.
The following is the test script:
ip netns add cl
ip l add dev vethc type veth peer name eth0 netns cl
ifconfig vethc 172.168.0.7/24 up
ip l add dev tun1000 type gretap key 1000
ip link add user1000 type vrf table 1
ip l set user1000 up
ip l set dev tun1000 master user1000
ifconfig tun1000 10.0.1.1/24 up
ip netns exec cl ifconfig eth0 172.168.0.17/24 up
ip netns exec cl ip l add dev tun type gretap local 172.168.0.17 remote 172.168.0.7 key 1000
ip netns exec cl ifconfig tun 10.0.1.7/24 up
ip r r 10.0.1.7 encap ip id 1000 dst 172.168.0.17 key dev tun1000 table 1
With this patch
ip netns exec cl ping 10.0.1.1 can success
Signed-off-by: wenxu <wenxu@ucloud.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
<<<<<<< HEAD
void *bpf_map_area_alloc(u64 size, int numa_node)
=======
static void *__bpf_map_area_alloc(u64 size, int numa_node, bool mmapable)
>>>>>>> 196e8ca74886c433dcfc64a809707074b936aaf5
<<<<<<< HEAD
if (size <= (PAGE_SIZE << PAGE_ALLOC_COSTLY_ORDER)) {
=======
/* kmalloc()'ed memory can't be mmap()'ed */
if (!mmapable && size <= (PAGE_SIZE << PAGE_ALLOC_COSTLY_ORDER)) {
>>>>>>> 196e8ca74886c433dcfc64a809707074b936aaf5
The main changes are:
1) Addition of BPF trampoline which works as a bridge between kernel functions,
BPF programs and other BPF programs along with two new use cases: i) fentry/fexit
BPF programs for tracing with practically zero overhead to call into BPF (as
opposed to k[ret]probes) and ii) attachment of the former to networking related
programs to see input/output of networking programs (covering xdpdump use case),
from Alexei Starovoitov.
2) BPF array map mmap support and use in libbpf for global data maps; also a big
batch of libbpf improvements, among others, support for reading bitfields in a
relocatable manner (via libbpf's CO-RE helper API), from Andrii Nakryiko.
3) Extend s390x JIT with usage of relative long jumps and loads in order to lift
the current 64/512k size limits on JITed BPF programs there, from Ilya Leoshkevich.
4) Add BPF audit support and emit messages upon successful prog load and unload in
order to have a timeline of events, from Daniel Borkmann and Jiri Olsa.
5) Extension to libbpf and xdpsock sample programs to demo the shared umem mode
(XDP_SHARED_UMEM) as well as RX-only and TX-only sockets, from Magnus Karlsson.
6) Several follow-up bug fixes for libbpf's auto-pinning code and a new API
call named bpf_get_link_xdp_info() for retrieving the full set of prog
IDs attached to XDP, from Toke Høiland-Jørgensen.
7) Add BTF support for array of int, array of struct and multidimensional arrays
and enable it for skb->cb[] access in kfree_skb test, from Martin KaFai Lau.
8) Fix AF_XDP by using the correct number of channels from ethtool, from Luigi Rizzo.
9) Two fixes for BPF selftest to get rid of a hang in test_tc_tunnel and to avoid
xdping to be run as standalone, from Jiri Benc.
10) Various BPF selftest fixes when run with latest LLVM trunk, from Yonghong Song.
11) Fix a memory leak in BPF fentry test run data, from Colin Ian King.
12) Various smaller misc cleanups and improvements mostly all over BPF selftests and
samples, from Daniel T. Lee, Andre Guedes, Anders Roxell, Mao Wenan, Yue Haibing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 20 Nov 2019 22:04:44 +0000 (23:04 +0100)]
bpf: Switch bpf_map_{area_alloc,area_mmapable_alloc}() to u64 size
Given we recently extended the original bpf_map_area_alloc() helper in
commit fc9702273e2e ("bpf: Add mmap() support for BPF_MAP_TYPE_ARRAY"),
we need to apply the same logic as in ff1c08e1f74b ("bpf: Change size
to u64 for bpf_map_{area_alloc, charge_init}()"). To avoid conflicts,
extend it for bpf-next.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Daniel Borkmann [Wed, 20 Nov 2019 21:38:16 +0000 (22:38 +0100)]
bpf: Emit audit messages upon successful prog load and unload
Allow for audit messages to be emitted upon BPF program load and
unload for having a timeline of events. The load itself is in
syscall context, so additional info about the process initiating
the BPF prog creation can be logged and later directly correlated
to the unload event.
The only info really needed from BPF side is the globally unique
prog ID where then audit user space tooling can query / dump all
info needed about the specific BPF program right upon load event
and enrich the record, thus these changes needed here can be kept
small and non-intrusive to the core.
Heiner Kallweit [Wed, 20 Nov 2019 20:08:47 +0000 (21:08 +0100)]
r8169: add check for PHY_MDIO_CHG to rtl_nic_fw_data_ok
Only values 0 and 1 are currently defined as parameters for
PHY_MDIO_CHG. Instead of silently ignoring unknown values and
misinterpreting the firmware code let's explicitly check.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If network device drives are using deferred probing, it was possible
that waiting for devices to show up in ipconfig was already over,
when the device eventually showed up. By calling wait_for_device_probe()
we now make sure deferred probing is done before checking for available
devices.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Mao Wenan [Wed, 20 Nov 2019 15:56:34 +0000 (16:56 +0100)]
vsock/vmci: make vmci_vsock_cb_host_called static
When using make C=2 drivers/misc/vmw_vmci/vmci_driver.o
to compile, below warning can be seen:
drivers/misc/vmw_vmci/vmci_driver.c:33:6: warning:
symbol 'vmci_vsock_cb_host_called' was not declared. Should it be static?
This patch make symbol vmci_vsock_cb_host_called static.
Fixes: b1bba80a4376 ("vsock/vmci: register vmci_transport only when VMCI guest/host are active") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Mao Wenan <maowenan@huawei.com> Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 20 Nov 2019 20:34:37 +0000 (12:34 -0800)]
Merge branch 'page_pool-DMA-sync'
Lorenzo Bianconi says:
====================
add DMA-sync-for-device capability to page_pool API
Introduce the possibility to sync DMA memory for device in the page_pool API.
This feature allows to sync proper DMA size and not always full buffer
(dma_sync_single_for_device can be very costly).
Please note DMA-sync-for-CPU is still device driver responsibility.
Relying on page_pool DMA sync mvneta driver improves XDP_DROP pps of
about 170Kpps:
- XDP_DROP DMA sync managed by mvneta driver: ~420Kpps
- XDP_DROP DMA sync managed by page_pool API: ~585Kpps
Do not change naming convention for the moment since the changes will hit other
drivers as well. I will address it in another series.
Changes since v4:
- do not allow the driver to set max_len to 0
- convert PP_FLAG_DMA_MAP/PP_FLAG_DMA_SYNC_DEV to BIT() macro
Changes since v3:
- move dma_sync_for_device before putting the page in ptr_ring in
__page_pool_recycle_into_ring since ptr_ring can be consumed
concurrently. Simplify the code moving dma_sync_for_device
before running __page_pool_recycle_direct/__page_pool_recycle_into_ring
Changes since v2:
- rely on PP_FLAG_DMA_SYNC_DEV flag instead of dma_sync
Changes since v1:
- rename sync in dma_sync
- set dma_sync_size to 0xFFFFFFFF in page_pool_recycle_direct and
page_pool_put_page routines
- Improve documentation
====================
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Bianconi [Wed, 20 Nov 2019 14:54:19 +0000 (16:54 +0200)]
net: mvneta: get rid of huge dma sync in mvneta_rx_refill
Get rid of costly dma_sync_single_for_device in mvneta_rx_refill
since now the driver can let page_pool API to manage needed DMA
sync with a proper size.
- XDP_DROP DMA sync managed by mvneta driver: ~420Kpps
- XDP_DROP DMA sync managed by page_pool API: ~585Kpps
Tested-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Bianconi [Wed, 20 Nov 2019 14:54:18 +0000 (16:54 +0200)]
net: page_pool: add the possibility to sync DMA memory for device
Introduce the following parameters in order to add the possibility to sync
DMA memory for device before putting allocated pages in the page_pool
caches:
- PP_FLAG_DMA_SYNC_DEV: if set in page_pool_params flags, all pages that
the driver gets from page_pool will be DMA-synced-for-device according
to the length provided by the device driver. Please note DMA-sync-for-CPU
is still device driver responsibility
- offset: DMA address offset where the DMA engine starts copying rx data
- max_len: maximum DMA memory size page_pool is allowed to flush. This
is currently used in __page_pool_alloc_pages_slow routine when pages
are allocated from page allocator
These parameters are supposed to be set by device drivers.
This optimization reduces the length of the DMA-sync-for-device.
The optimization is valid because pages are initially
DMA-synced-for-device as defined via max_len. At RX time, the driver
will perform a DMA-sync-for-CPU on the memory for the packet length.
What is important is the memory occupied by packet payload, because
this is the area CPU is allowed to read and modify. As we don't track
cache-lines written into by the CPU, simply use the packet payload length
as dma_sync_size at page_pool recycle time. This also take into account
any tail-extend.
Tested-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Bianconi [Wed, 20 Nov 2019 14:54:17 +0000 (16:54 +0200)]
net: mvneta: rely on page_pool_recycle_direct in mvneta_run_xdp
Rely on page_pool_recycle_direct and not on xdp_return_buff in
mvneta_run_xdp. This is a preliminary patch to limit the dma sync len
to the one strictly necessary
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: sched: pie: enable timestamp based delay calculation
RFC 8033 suggests an alternative approach to calculate the queue
delay in PIE by using a timestamp on every enqueued packet. This
patch adds an implementation of that approach and sets it as the
default method to calculate queue delay. The previous method (based
on Little's law) to calculate queue delay is set as optional.
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com> Signed-off-by: Leslie Monis <lesliemonis@gmail.com> Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in> Acked-by: Dave Taht <dave.taht@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This series of patches add support to offload TC-MATCHALL classifier
to hardware to classify all outgoing and incoming traffic on the
underlying port. Only 1 egress and 1 ingress rule each can be
offloaded on the underlying port.
Patch 1 adds support for TC-MATCHALL classifier offload on the egress
side. TC-POLICE is the only action that can be offloaded on the egress
side and is used to rate limit all outgoing traffic to specified max
rate.
Patch 2 adds logic to reject the current rule offload if its priority
conflicts with existing rules in the TCAM.
Patch 3 adds support for TC-MATCHALL classifier offload on the ingress
side. The same set of actions supported by existing TC-FLOWER
classifier offload can be applied on all the incoming traffic.
v5:
- Fixed commit message and comment to include comparison for equal
priority in patch 2.
v4:
- Removed check in patch 1 to reject police offload if prio is not 1.
- Moved TC_SETUP_BLOCK code to separate function in patch 1.
- Added logic to ensure the prio passed by TC doesn't conflict with
other rules in TCAM in patch 2.
- Higher index has lower priority than lower index in TCAM. So, rework
cxgb4_get_free_ftid() to search free index from end of TCAM in
descending order in patch 2.
- Added check to ensure the matchall rule's prio doesn't conflict with
other rules in TCAM in patch 3.
- Added logic to fill default mask for VIID, if none has been
provided, to prevent conflict with duplicate VIID rules in patch 3.
- Used existing variables in private structure to fill VIID info,
instead of extracting the info manually in patch 3.
v3:
- Added check in patch 1 to reject police offload if prio is not 1.
- Assign block_shared variable only for TC_SETUP_BLOCK in patch 1.
v2:
- Added check to reject flow block sharing for policers in patch 1.
- Removed logic to fetch free index from end of TCAM in patch 2.
Must maintain the same ordering as in kernel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Rahul Lakkireddy [Wed, 20 Nov 2019 00:16:08 +0000 (05:46 +0530)]
cxgb4: add TC-MATCHALL classifier ingress offload
Add TC-MATCHALL classifier ingress offload support. The same actions
supported by existing TC-FLOWER offload can be applied to all incoming
traffic on the underlying interface.
Ensure the rule priority doesn't conflict with existing rules in the
TCAM. Only 1 ingress matchall rule can be active at a time on the
underlying interface.
v5:
- No change.
v4:
- Added check to ensure the matchall rule's prio doesn't conflict with
other rules in TCAM.
- Added logic to fill default mask for VIID, if none has been
provided, to prevent conflict with duplicate VIID rules.
- Used existing variables in private structure to fill VIID info,
instead of extracting the info manually.
v3:
- No change.
v2:
- Removed logic to fetch free index from end of TCAM. Must maintain
same ordering as in kernel.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rahul Lakkireddy [Wed, 20 Nov 2019 00:16:07 +0000 (05:46 +0530)]
cxgb4: check rule prio conflicts before offload
Only offload rule if it satisfies both of the following conditions:
1. The immediate previous rule has priority <= current rule's priority.
2. The immediate next rule has priority >= current rule's priority.
Also rework free entry fetch logic to search from end of TCAM, instead
of beginning, because higher indices have lower priority than lower
indices. This is similar to how TC auto generates priority values.
v5:
- Fixed commit message and comment to include comparison for equal
priority.
v4:
- Patch added in this version.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rahul Lakkireddy [Wed, 20 Nov 2019 00:16:06 +0000 (05:46 +0530)]
cxgb4: add TC-MATCHALL classifier egress offload
Add TC-MATCHALL classifier offload with TC-POLICE action applied for
all outgoing traffic on the underlying interface. Split flow block
offload to support both egress and ingress classification.
For example, to rate limit all outgoing traffic to 1 Gbps:
Note that skip_sw is important. Otherwise, both stack and hardware
will end up doing policing. Policing can't be shared across flow
blocks. Only 1 egress matchall rule can be active at a time on the
underlying interface.
v5:
- No change.
v4:
- Removed check to reject police offload if prio is not 1.
- Moved TC_SETUP_BLOCK code to separate function.
v3:
- Added check to reject police offload if prio is not 1.
- Assign block_shared variable only for TC_SETUP_BLOCK.
v2:
- Added check to reject flow block sharing for policers.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
page_pool: API for numa node change handling
This series extends page pool API to allow page pool consumers to update
page pool numa node on the fly. This is required since on some systems,
rx rings irqs can migrate between numa nodes, due to irq balancer or user
defined scripts, current page pool has no way to know of such migration
and will keep allocating and holding on to pages from a wrong numa node,
which is bad for the consumer performance.
1) Add API to update numa node id of the page pool
Consumers will call this API to update the page pool numa node id.
2) Don't recycle non-reusable pages:
Page pool will check upon page return whether a page is suitable for
recycling or not.
2.1) when it belongs to a different num node.
2.2) when it was allocated under memory pressure.
3) mlx5 will use the new API to update page pool numa id on demand.
The series is a joint work between me and Jonathan, we tested it and it
proved itself worthy to avoid page allocator bottlenecks and improve
packet rate and cpu utilization significantly for the described
scenarios above.
Performance testing:
XDP drop/tx rate and TCP single/multi stream, on mlx5 driver
while migrating rx ring irq from close to far numa:
mlx5 internal page cache was locally disabled to get pure page pool
results.
CPU: Intel(R) Xeon(R) CPU E5-2603 v4 @ 1.70GHz
NIC: Mellanox Technologies MT27700 Family [ConnectX-4] (100G)
XDP Drop/TX single core:
NUMA | XDP | Before | After
---------------------------------------
Close | Drop | 11 Mpps | 10.9 Mpps
Far | Drop | 4.4 Mpps | 5.8 Mpps
Close | TX | 6.5 Mpps | 6.5 Mpps
Far | TX | 3.5 Mpps | 4 Mpps
Improvement is about 30% drop packet rate, 15% tx packet rate for numa
far test.
No degradation for numa close tests.
TCP single/multi cpu/stream:
NUMA | #cpu | Before | After
--------------------------------------
Close | 1 | 18 Gbps | 18 Gbps
Far | 1 | 15 Gbps | 18 Gbps
Close | 12 | 80 Gbps | 80 Gbps
Far | 12 | 68 Gbps | 80 Gbps
In all test cases we see improvement for the far numa case, and no
impact on the close numa case.
==================
Performance analysis and conclusions by Jesper [1]:
Impact on XDP drop x86_64 is inconclusive and shows only 0.3459ns
slow-down, as this is below measurement accuracy of system.
v2->v3:
- Rebase on top of latest net-next and Jesper's page pool object
release patchset [2]
- No code changes
- Performance analysis by Jesper added to the cover letter.
v1->v2:
- Drop last patch, as requested by Ilias and Jesper.
- Fix documentation's performance numbers order.
Saeed Mahameed [Wed, 20 Nov 2019 00:15:21 +0000 (00:15 +0000)]
net/mlx5e: Rx, Update page pool numa node when changed
Once every napi poll cycle, check if numa node is different than
the page pool's numa id, and update it using page_pool_update_nid().
Alternatively, we could have registered an irq affinity change handler,
but page_pool_update_nid() must be called from napi context anyways, so
the handler won't actually help.
Performance testing:
XDP drop/tx rate and TCP single/multi stream, on mlx5 driver
while migrating rx ring irq from close to far numa:
mlx5 internal page cache was locally disabled to get pure page pool
results.
CPU: Intel(R) Xeon(R) CPU E5-2603 v4 @ 1.70GHz
NIC: Mellanox Technologies MT27700 Family [ConnectX-4] (100G)
XDP Drop/TX single core:
NUMA | XDP | Before | After
---------------------------------------
Close | Drop | 11 Mpps | 10.9 Mpps
Far | Drop | 4.4 Mpps | 5.8 Mpps
Close | TX | 6.5 Mpps | 6.5 Mpps
Far | TX | 3.5 Mpps | 4 Mpps
Improvement is about 30% drop packet rate, 15% tx packet rate for numa
far test.
No degradation for numa close tests.
TCP single/multi cpu/stream:
NUMA | #cpu | Before | After
--------------------------------------
Close | 1 | 18 Gbps | 18 Gbps
Far | 1 | 15 Gbps | 18 Gbps
Close | 12 | 80 Gbps | 80 Gbps
Far | 12 | 68 Gbps | 80 Gbps
In all test cases we see improvement for the far numa case, and no
impact on the close numa case.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Wed, 20 Nov 2019 00:15:19 +0000 (00:15 +0000)]
page_pool: Don't recycle non-reusable pages
A page is NOT reusable when at least one of the following is true:
1) allocated when system was under some pressure. (page_is_pfmemalloc)
2) belongs to a different NUMA node than pool->p.nid.
To update pool->p.nid users should call page_pool_update_nid().
Holding on to such pages in the pool will hurt the consumer performance
when the pool migrates to a different numa node.
Performance testing:
XDP drop/tx rate and TCP single/multi stream, on mlx5 driver
while migrating rx ring irq from close to far numa:
mlx5 internal page cache was locally disabled to get pure page pool
results.
CPU: Intel(R) Xeon(R) CPU E5-2603 v4 @ 1.70GHz
NIC: Mellanox Technologies MT27700 Family [ConnectX-4] (100G)
XDP Drop/TX single core:
NUMA | XDP | Before | After
---------------------------------------
Close | Drop | 11 Mpps | 10.9 Mpps
Far | Drop | 4.4 Mpps | 5.8 Mpps
Close | TX | 6.5 Mpps | 6.5 Mpps
Far | TX | 3.5 Mpps | 4 Mpps
Improvement is about 30% drop packet rate, 15% tx packet rate for numa
far test.
No degradation for numa close tests.
TCP single/multi cpu/stream:
NUMA | #cpu | Before | After
--------------------------------------
Close | 1 | 18 Gbps | 18 Gbps
Far | 1 | 15 Gbps | 18 Gbps
Close | 12 | 80 Gbps | 80 Gbps
Far | 12 | 68 Gbps | 80 Gbps
In all test cases we see improvement for the far numa case, and no
impact on the close numa case.
The impact of adding a check per page is very negligible, and shows no
performance degradation whatsoever, also functionality wise it seems more
correct and more robust for page pool to verify when pages should be
recycled, since page pool can't guarantee where pages are coming from.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Wed, 20 Nov 2019 00:15:17 +0000 (00:15 +0000)]
page_pool: Add API to update numa node
Add page_pool_update_nid() to be called by page pool consumers when they
detect numa node changes.
It will update the page pool nid value to start allocating from the new
effective numa node.
This is to mitigate page pool allocating pages from a wrong numa node,
where the pool was originally allocated, and holding on to pages that
belong to a different numa node, which causes performance degradation.
For pages that are already being consumed and could be returned to the
pool by the consumer, in next patch we will add a check per page to avoid
recycling them back to the pool and return them to the page allocator.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 20 Nov 2019 19:25:24 +0000 (11:25 -0800)]
Merge branch 'cpsw-switchdev'
Grygorii Strashko says:
====================
net: ethernet: ti: introduce new cpsw switchdev based driver
Thank you All for review of v6.
There are no significant changes in this version, just fixed comments to v6.
--- v6
The major change in this version is DT bindings conversation to json-schema, and
fixed other comments to v5. Also added patch to clean up ALE on init and netif
restart.
--- v5
The major part of work done in this iteration is rebasing on top of net-next
with XDP series from Ivan Khoronzhuk [3], and enable XDP support in the new
CPSW switchdev driver (it was little bit painful ;(). There are mostly no
functional changes in new CPSW driver, just few fixes, sync with old driver
and cleanups/optimizations. So, I've kept rest of cover letter unchanged.
---
This series originally based on work [1][2] done by
Ilias Apalodimas <ilias.apalodimas@linaro.org>.
This the RFC v5 which introduces new CPSW switchdev based driver which is
operating in dual-emac mode by default, thus working as 2 individual
network interfaces. The Switch mode can be enabled by configuring devlink driver
parameter "switch_mode" to 1/true:
devlink dev param set platform/48484000.switch \
name switch_mode value 1 cmode runtime
This can be done regardless of the state of Port's netdev devices - UP/DOWN, but
Port's netdev devices have to be in UP before joining the bridge to avoid
overwriting of bridge configuration as CPSW switch driver completely reloads its
configuration when first Port changes its state to UP.
When the both interfaces joined the bridge - CPSW switch driver will start
marking packets with offload_fwd_mark flag unless "ale_bypass=0".
All configuration is implemented via switchdev API.
The previous solution of tracking both Ports joined the bridge
(from netdevice_notifier) proved to be not correct as changing CPSW switch
driver mode required cleanup of ALE table and CPSW settings which happens
while second Port is joined bridge and as result configuration loaded
by bridge for the first Port became corrupted.
The introduction of the new CPSW switchdev based driver (cpsw_new.c) is split
on two parts: Part 1 - basic dual-emac driver; Part 2 switchdev support.
Such approach has simplified code development and testing alot. And, I hope,
it will help with better review.
patches #1 - 5: preparation patches which also moves common code to cpsw_priv.c
patches #6 - 9: Introduce TI CPSW switch driver based on switchdev and new
DT bindings
patch #10: new CPSW switchdev driver documentation
patch #11: adds DT nodes for new CPSW switchdev driver added for DRA7 SoC
patch #12: adds DT nodes for new cpsw switchdev driver for am571x-idk board
patch #13: enables build of TI CPSW driver
Most of the contents of the previous cover-letter have been added in
new driver documentation, so please refer to that for configuration,
testing and future work.
These patches can be found at (branch contains some additional patches required
for testing on top of net-next):
https://github.com/grygoriyS/linux.git
branch: lkml-5.4-switch-tbd-v7
changes in v7:
- patch 2: added check for devm_kmalloc_array() return value
- patch 6: fixed comments
changes in v6: https://lkml.org/lkml/2019/11/9/108
- DT bindings converted to json-schema
- netdev initialization is split on creation and registration.
The netdevs registration happens now at the end of the pobe.
- reworked cpsw_set_pauseparam() to use PHYlib APIs.
- other comments for v5 fixed
v5: https://patchwork.kernel.org/cover/11208785/
- rebase on top of net-next with XDP series from Ivan Khoronzhuk [3],
and enable XDP support in the new CPSW switchdev driver
cpsw driver (tested XDP_DROP only)
- sync with old cpsw driver
- implement comments from Ivan Khoronzhuk and Rob Herring
- fixed "NETDEV WATCHDOG: .." warning after interface after interface UP/DOWN,
missed TX wake in cpsw_adjust_link()
v4: https://patchwork.kernel.org/cover/11010523/
- finished split of common CPSW code
- added devlink support
- changed CPSW mode configuration approach: from netdevice_notifier to devlink
parameter
- refactor and clean up ALE changes which allows to modify VLANs/MDBs entries
- added missed support for port QDISC_CBS and QDISC_MQPRIO
- the CPSW is split on two parts: basic dual_mac driver and switchdev support
- added missed callback .ndo_get_port_parent_id()
- reworked ingress frames marking in switch mode (offload_fwd_mark)
- applied comments from Andrew Lunn
v3: https://lwn.net/Articles/786677/
Changes in v3:
- alot of work done to split properly common code between legacy and switchdev
CPSW drivers and clean up code
- CPSW switchdev interface updated to the current LKML switchdev interface
- actually new CPSW switchdev based driver introduced
- optimized dual_mac mode in new driver. Main change is that in promiscuous
mode P0_UNI_FLOOD (both ports) is enabled in addition to ALLMULTI (current
port) instead of ALE_BYPASS. So, port in non promiscuous mode will keep
possibility of mcast and vlan filtering.
- changed bridge join sequnce: now switch mode will be enabled only when
both ports joined the bridge. CPSW will be switched to dual_mac mode if any
port leave bridge. ALE table is completly cleared and then refiled while
switching to switch mode - this simplidies code a lot, but introduces some
limitation to bridge setup sequence:
ip link add name br0 type bridge
ip link set dev br0 type bridge ageing_time 1000
ip link set dev br0 type bridge vlan_filtering 0 <- disable
echo 0 > /sys/class/net/br0/bridge/default_vlan
ip link set dev sw0p1 up <- add ports
ip link set dev sw0p2 up
ip link set dev sw0p1 master br0
ip link set dev sw0p2 master br0
echo 1 > /sys/class/net/br0/bridge/default_vlan <- enable
ip link set dev br0 type bridge vlan_filtering 1
bridge vlan add dev br0 vid 1 pvid untagged self
- STP tested with vlan_filtering 1/0. To make STP work I've had to set
NO_SA_UPDATE for all slave ports (see comment in code). It also required to
statically register STP mcast address {0x01, 0x80, 0xc2, 0x0, 0x0, 0x0};
- allowed build both TI_CPSW and TI_CPSW_SWITCHDEV drivers
- PTP can be enabled on both ports in dual_mac mode
Ilias Apalodimas [Tue, 19 Nov 2019 22:19:22 +0000 (00:19 +0200)]
Documentation: networking: add cpsw switchdev based driver documentation
A new cpsw dirver based on switchdev was added. Add documentation about
basic configuration and future features
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilias Apalodimas [Tue, 19 Nov 2019 22:19:20 +0000 (00:19 +0200)]
net: ethernet: ti: introduce cpsw switchdev based driver part 2 - switch
CPSW switchdev based driver which is operating in dual-emac mode by
default, thus working as 2 individual network interfaces. The Switch mode
can be enabled by configuring devlink driver parameter "switch_mode" to 1:
devlink dev param set platform/48484000.switch \
name switch_mode value 1 cmode runtime
This can be done regardless of the state of Port's netdevs - UP/DOWN, but
Port's netdev devices have to be UP before joining the bridge to avoid
overwriting of bridge configuration as CPSW switch driver completely
reloads its configuration when first Port changes its state to UP.
When the both interfaces joined the bridge - CPSW switch driver will start
marking packets with offload_fwd_mark flag unless "ale_bypass=0".
All configuration is implemented via switchdev API and notifiers.
Supported:
- SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS
- SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS: BR_MCAST_FLOOD
- SWITCHDEV_ATTR_ID_PORT_STP_STATE
- SWITCHDEV_OBJ_ID_PORT_VLAN
- SWITCHDEV_OBJ_ID_PORT_MDB
- SWITCHDEV_OBJ_ID_HOST_MDB
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilias Apalodimas [Tue, 19 Nov 2019 22:19:19 +0000 (00:19 +0200)]
net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac
Part 1:
Introduce basic CPSW dual_mac driver (cpsw_new.c) which is operating in
dual-emac mode by default, thus working as 2 individual network interfaces.
Main differences from legacy CPSW driver are:
- optimized promiscuous mode: The P0_UNI_FLOOD (both ports) is enabled in
addition to ALLMULTI (current port) instead of ALE_BYPASS. So, Ports in
promiscuous mode will keep possibility of mcast and vlan filtering, which
is provides significant benefits when ports are joined to the same bridge,
but without enabling "switch" mode, or to different bridges.
- learning disabled on ports as it make not too much sense for
segregated ports - no forwarding in HW.
- enabled basic support for devlink.
dt-bindings: net: ti: add new cpsw switch driver bindings
Add bindings for the new TI CPSW switch driver. Comparing to the legacy
bindings (net/cpsw.txt):
- ports definition follows DSA bindings (net/dsa/dsa.txt) and ports can be
marked as "disabled" if not physically wired.
- all deprecated properties dropped;
- all legacy propertiies dropped which represent constant HW cpapbilities
(cpdma_channels, ale_entries, bd_ram_size, mac_control, slaves,
active_slave)
- TI CPTS DT properties are reused as is, but grouped in "cpts" sub-node
- TI Davinci MDIO DT bindings are reused as is, because Davinci MDIO is
reused.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ethernet: ti: cpsw: move set of common functions in cpsw_priv
As a preparatory patch to add support for a switchdev based cpsw driver,
move common functions to cpsw-priv.c so that they can be used across both
drivers.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ethernet: ti: cpsw: resolve build deps of cpsw drivers
A following patches introduce new CPSW switchdev driver which uses common
code with legacy CPSW driver. This will introduce build dependency between
CPSW switchdev and CPSW legacy drivers related to for_each_slave() and
cpsw_slave_index() - they can be compiled both, but only one of them will
be not functional depending in Kconfig settings due to duffrences in Slave
Ports indexes calculation.
To fix this make for_each_slave() local (it's used now only by legacy CPSW
driver) and convert cpsw_slave_index() to be a function pointer which is
assigned in probe. Driver to probe is defined by DT.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilias Apalodimas [Tue, 19 Nov 2019 22:19:15 +0000 (00:19 +0200)]
net: ethernet: ti: ale: modify vlan/mdb api for switchdev
A following patch introduces switchdev functionality, so modify
ALE engine VLANs/MDBs API:
- cpsw_ale_del_mcast(): update so it will remove only selected ports from
mcast port_mask or delete whole mcast record if !port_mask
- cpsw_ale_del_vlan(): update so it will remove only selected ports from
all VLAN record's masks or delete whole VLAN record if !port_mask
- add cpsw_ale_vlan_add_modify() to add or modify existing VLAN record's
masks
- add cpsw_ale_set_unreg_mcast() for enabling unreg mcast on port VLANs
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ethernet: ti: cpsw: allow untagged traffic on host port
Now untagged vlan traffic is not support on Host P0 port. This patch adds
in ALE context bitmap of VLANs for which Host P0 port bit set in Force
Untagged Packet Egress bitmask in VLANs ALE entries, and adds corresponding
check in VLAN incapsulation header parsing function cpsw_rx_vlan_encap().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
nf_tables_offload: vlan matching support
The following patchset contains Netfilter support for vlan matching
offloads:
1) Constify nft_reg_load() as a preparation patch.
2) Restrict rule matching to ingress interface type ARPHRD_ETHER.
3) Add new vlan_tci field to flow_dissector_key_vlan structure,
to allow to set up vlan_id, vlan_dei and vlan_priority in one go.
4) C-VLAN matching support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: nft_payload: add C-VLAN offload support
Match on h_vlan_encapsulated_proto and set up protocol dependency. Check
for protocol dependency before accessing the tci field. Allow to match
on the encapsulated ethertype too.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Match on ethertype and set up protocol dependency. Check for protocol
dependency before accessing the tci field. Allow to match on the
encapsulated ethertype too.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: nf_tables_offload: allow ethernet interface type only
Hardware offload support at this stage assumes an ethernet device in
place. The flow dissector provides the intermediate representation to
express this selector, so extend it to allow to store the interface
type. Flower does not uses this, so skb_flow_dissect_meta() is not
extended to match on this new field.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Tue, 19 Nov 2019 09:39:11 +0000 (17:39 +0800)]
lwtunnel: add support for multiple geneve opts
geneve RFC (draft-ietf-nvo3-geneve-14) allows a geneve packet to carry
multiple geneve opts, so it's necessary for lwtunnel to support adding
multiple geneve opts in one lwtunnel route. But vxlan and erspan opts
are still only allowed to add one option.
With this patch, iproute2 could make it like:
# ip r a 1.1.1.0/24 encap ip id 1 geneve_opts 0:0:12121212,1:2:12121212 \
dst 10.1.0.2 dev geneve1
# ip r a 1.1.1.0/24 encap ip id 1 vxlan_opts 456 \
dst 10.1.0.2 dev erspan1
# ip r a 1.1.1.0/24 encap ip id 1 erspan_opts 1:123:0:0 \
dst 10.1.0.2 dev erspan1
Which are pretty much like cls_flower and act_tunnel_key.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrii Nakryiko [Wed, 20 Nov 2019 00:25:10 +0000 (16:25 -0800)]
selftests/bpf: Enforce no-ALU32 for test_progs-no_alu32
With the most recent Clang, alu32 is enabled by default if -mcpu=probe or
-mcpu=v3 is specified. Use a separate build rule with -mcpu=v2 to enforce no
ALU32 mode.
Fixes: 4846d5330daf ("cxgb4: add Tx and Rx path for ETHOFLD traffic") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 18 Nov 2019 18:16:57 +0000 (20:16 +0200)]
net: dsa: felix: Fix CPU port assignment when not last port
On the NXP LS1028A, there are 2 Ethernet links between the Felix switch
and the ENETC:
- eno2 <-> swp4, at 2.5G
- eno3 <-> swp5, at 1G
Only one of the above Ethernet port pairs can act as a DSA link for
tagging.
When adding initial support for the driver, it was tested only on the 1G
eno3 <-> swp5 interface, due to the necessity of using PHYLIB initially
(which treats fixed-link interfaces as emulated C22 PHYs, so it doesn't
support fixed-link speeds higher than 1G).
After making PHYLINK work, it appears that swp4 still can't act as CPU
port. So it looks like ocelot_set_cpu_port was being called for swp4,
but then it was called again for swp5, overwriting the CPU port assigned
in the DT.
It appears that when you call dsa_upstream_port for a port that is not
defined in the device tree (such as swp5 when using swp4 as CPU port),
its dp->cpu_dp pointer is not initialized by dsa_tree_setup_default_cpu,
and this trips up the following condition in dsa_upstream_port:
if (!cpu_dp)
return port;
So the moral of the story is: don't call dsa_upstream_port for a port
that is not defined in the device tree, and therefore its dsa_port
structure is not completely initialized (ds->num_ports is still 6).
Fixes: 56051948773e ("net: dsa: ocelot: add driver for Felix switch family") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When relocating subprogram call, libbpf doesn't take into account
relo->text_off, which comes from symbol's value. This generally works fine for
subprograms implemented as static functions, but breaks for global functions.
Taking a simplified test_pkt_access.c as an example:
test_pkt_access_subprog1 and test_pkt_access_subprog2 offsets (targets of two
calls) are encoded within call instruction's imm32 part as -1 and 2,
respectively:
Now, if we compile example with global functions, the setup changes.
Relocations are now against specifically test_pkt_access_subprog1 and
test_pkt_access_subprog2 symbols, with test_pkt_access_subprog2 pointing 24
bytes into its respective section (.text), i.e., 3 instructions in:
Thus the right formula to calculate target call offset after relocation should
take into account relocation's target symbol value (offset within section),
call instruction's imm32 offset, and (subtracting, to get relative instruction
offset) instruction index of call instruction itself. All that is shifted by
number of instructions in main program, given all sub-programs are copied over
after main program.
Convert few selftests relying on bpf-to-bpf calls to use global functions
instead of static ones.
Fixes: 48cca7e44f9f ("libbpf: add support for bpf_call") Reported-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Andrii Nakryiko <andriin@fb.com> Acked-by: Yonghong Song <yhs@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/bpf/20191119224447.3781271-1-andriin@fb.com
Luigi Rizzo [Tue, 19 Nov 2019 00:19:51 +0000 (16:19 -0800)]
net-af_xdp: Use correct number of channels from ethtool
Drivers use different fields to report the number of channels, so take
the maximum of all data channels (rx, tx, combined) when determining the
size of the xsk map. The current code used only 'combined' which was set
to 0 in some drivers e.g. mlx4.
Tested: compiled and run xdpsock -q 3 -r -S on mlx4
Signed-off-by: Luigi Rizzo <lrizzo@google.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Magnus Karlsson <magnus.karlsson@intel.com> Link: https://lore.kernel.org/bpf/20191119001951.92930-1-lrizzo@google.com
====================
This patch series introduces usage of relative long jumps and loads in
order to lift 64/512k size limits on JITed BPF programs on s390.
Patch 1 introduces long relative branches.
Patch 2 changes the way literal pool is arranged in order to be
compatible with long relative loads.
Patch 3 changes the way literal pool base register is loaded for large
programs.
Patch 4 replaces regular loads with long relative loads where they are
totally superior.
Patch 5 introduces long relative loads as an alternative way to load
constants in large programs. Regular loads are kept and still used for
small programs.
Patch 6 removes the size limit check.
====================
Ilya Leoshkevich [Mon, 18 Nov 2019 18:03:40 +0000 (19:03 +0100)]
s390/bpf: Remove JITed image size limitations
Now that jump and long displacement ranges are no longer a problem,
remove the limit on JITed image size. In practice it's still limited by
2G, but with verifier allowing "only" 1M instructions, it's not an
issue.
Ilya Leoshkevich [Mon, 18 Nov 2019 18:03:39 +0000 (19:03 +0100)]
s390/bpf: Use lg(f)rl when long displacement cannot be used
If literal pool grows past 524287 mark, it's no longer possible to use
long displacement to reference literal pool entries. In JIT setting
maintaining multiple literal pool registers is next to impossible, since
we operate on one instruction at a time.
Therefore, fall back to loading literal pool entry using PC-relative
addressing, and then using a register-register form of the following
machine instruction.
Ilya Leoshkevich [Mon, 18 Nov 2019 18:03:38 +0000 (19:03 +0100)]
s390/bpf: Use lgrl instead of lg where possible
lg and lgrl have the same performance characteristics, but the former
requires a base register and is subject to long displacement range
limits, while the latter does not. Therefore, lgrl is totally superior
to lg and should be used instead whenever possible.
Ilya Leoshkevich [Mon, 18 Nov 2019 18:03:37 +0000 (19:03 +0100)]
s390/bpf: Load literal pool register using larl
Currently literal pool register is loaded using basr, which makes it
point not to the beginning of the literal pool, but rather to the next
instruction. In case JITed code is larger than 512k, this renders
literal pool register absolutely useless due to long displacement range
restrictions.
The solution is to use larl to make literal pool register point to the
very beginning of the literal pool. This makes it always possible to
address 512k worth of literal pool entries using long displacement.
However, for short programs, in which the entire literal pool is covered
by basr-generated base, it is still beneficial to use basr, since it is
4 bytes shorter than larl.
Detect situations when basr-generated base does not cover the entire
literal pool, and in such cases use larl instead.
Ilya Leoshkevich [Mon, 18 Nov 2019 18:03:36 +0000 (19:03 +0100)]
s390/bpf: Align literal pool entries
When literal pool size exceeds 512k, it's no longer possible to
reference all the entries in it using a single base register and long
displacement. Therefore, PC-relative lgfrl and lgrl instructions need to
be used.
Unfortunately, they require their arguments to be aligned to 4- and
8-byte boundaries respectively. This generates certain overhead due to
necessary padding bytes. Grouping 4- and 8-byte entries together reduces
the maximum overhead to 6 bytes (2 for aligning 4-byte entries and 4 for
aligning 8-byte entries).
While in theory it is possible to detect whether or not alignment is
needed by comparing the literal pool size with 512k, in practice this
leads to having two ways of emitting constants, making the code more
complicated.
Prefer code simplicity over trivial size saving, and always group and
align literal pool entries.
Ilya Leoshkevich [Mon, 18 Nov 2019 18:03:35 +0000 (19:03 +0100)]
s390/bpf: Use relative long branches
Currently maximum JITed code size is limited to 64k, because JIT can
emit only relative short branches, whose range is limited by 64k in both
directions.
Teach JIT to use relative long branches. There are no compare+branch
relative long instructions, so using relative long branches consumes
more space due to having to having to emit an explicit comparison
instruction. Therefore do this only when relative short branch is not
enough.
Colin Ian King [Mon, 18 Nov 2019 11:48:35 +0000 (11:48 +0000)]
net: phy: dp83869: fix return of uninitialized variable ret
In the case where the call to phy_interface_is_rgmii returns zero
the variable ret is left uninitialized and this is returned at
the end of the function dp83869_configure_rgmii. Fix this by
returning 0 instead of the uninitialized value in ret.
Addresses-Coverity: ("Uninitialized scalar variable") Fixes: 01db923e8377 ("net: phy: dp83869: Add TI dp83869 phy") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 18 Nov 2019 10:10:12 +0000 (18:10 +0800)]
lwtunnel: change to use nla_put_u8 for LWTUNNEL_IP_OPT_ERSPAN_VER
LWTUNNEL_IP_OPT_ERSPAN_VER is u8 type, and nla_put_u8 should have
been used instead of nla_put_u32(). This is a copy-paste error.
Fixes: b0a21810bd5e ("lwtunnel: add options setting and dumping for erspan") Signed-off-by: Xin Long <lucien.xin@gmail.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 19 Nov 2019 01:13:29 +0000 (17:13 -0800)]
Merge branch 'bnxt_en-Updates'
Michael Chan says:
====================
bnxt_en: Updates.
This series has the firmware interface update that changes the aRFS/ntuple
interface on 57500 chips. The 2nd patch adds a counter and improves
the hardware buffer error handling on the 57500 chips. The rest of the
series is mainly enhancements on error recovery and firmware reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pavan Chebbi [Mon, 18 Nov 2019 08:56:43 +0000 (03:56 -0500)]
bnxt_en: Abort waiting for firmware response if there is no heartbeat.
This is especially beneficial during the NVRAM related firmware
commands that have longer timeouts. If the BNXT_STATE_FW_FATAL_COND
flag gets set while waiting for firmware response, abort and return
error.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vasundhara Volam [Mon, 18 Nov 2019 08:56:42 +0000 (03:56 -0500)]
bnxt_en: Add a warning message for driver initiated reset
During loss of heartbeat, log this warning message.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vasundhara Volam [Mon, 18 Nov 2019 08:56:41 +0000 (03:56 -0500)]
bnxt_en: Return proper error code for non-existent NVM variable
For NVM params that are not supported in the current NVM
configuration, return the error as -EOPNOTSUPP.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vasundhara Volam [Mon, 18 Nov 2019 08:56:40 +0000 (03:56 -0500)]
bnxt_en: Report health status update after reset is done
Report health status update to devlink health reporter, once
reset is completed.
Cc: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vasundhara Volam [Mon, 18 Nov 2019 08:56:39 +0000 (03:56 -0500)]
bnxt_en: Set MASTER flag during driver registration.
The Linux driver is capable of being the master function to handle
resets, so we set the flag to let firmware know. Some other
drivers, such as DPDK, is not capable and will not set the flag.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vasundhara Volam [Mon, 18 Nov 2019 08:56:38 +0000 (03:56 -0500)]
bnxt_en: Extend ETHTOOL_RESET to hot reset driver.
If firmware supports hot reset, extend ETHTOOL_RESET to support
hot reset driver which does not require a driver reload after
ETHTOOL_RESET. The driver will go through the same coordinated
reset sequence as a firmware initiated fatal/non-fatal reset.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vasundhara Volam [Mon, 18 Nov 2019 08:56:37 +0000 (03:56 -0500)]
bnxt_en: Increase firmware response timeout for coredump commands.
Use the larger HWRM_COREDUMP_TIMEOUT value for coredump related
data response from the firmware. These commands take longer than
normal commands.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 18 Nov 2019 08:56:36 +0000 (03:56 -0500)]
bnxt_en: Improve RX buffer error handling.
When hardware reports RX buffer errors, the latest 57500 chips do not
require reset. The packet is discarded by the hardware and the
ring will continue to operate.
Also, add an rx_buf_errors counter for this type of error. It can help
the user to identify if the aggregation ring is too small.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
selftests: Add ethtool and scale tests
This patch set adds generic ethtool tests and a mlxsw-specific router
scale test for Spectrum-2.
Patches #1-#2 from Danielle add the router scale test for Spectrum-2. It
re-uses the same test as Spectrum-1, but it is invoked with a different
scale, according to what it is queried from devlink-resource.
Patches #3-#5 from Amit are a re-work of the ethtool tests that were
posted in the past [1]. Patches #3-#4 add the necessary library
routines, whereas patch #5 adds the test itself. The test checks both
good and bad flows with autoneg on and off. The test plan it detailed in
the commit message.
Last time Andrew and Florian (copied) provided very useful feedback that
is incorporated in this set. Namely:
* Parse the value of the different link modes from
/usr/include/linux/ethtool.h
* Differentiate between supported and advertised speeds and use the
latter in autoneg tests
* Make the test generic and move it to net/forwarding/ instead of being
mlxsw-specific
Amit Cohen [Mon, 18 Nov 2019 07:50:02 +0000 (09:50 +0200)]
selftests: forwarding: Add speed and auto-negotiation test
Check configurations and packets transference with different variations
of autoneg and speed.
Test plan:
1. Test force of same speed with autoneg off
2. Test force of different speeds with autoneg off (should fail)
3. One side is autoneg on and other side sets force of common speeds
4. One side is autoneg on and other side only advertises a subset of the
common speeds (one speed of the subset)
5. One side is autoneg on and other side only advertises a subset of the
common speeds. Check that highest speed is negotiated
6. Test autoneg on, but each side advertises different speeds (should
fail)
Signed-off-by: Amit Cohen <amitc@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Mon, 18 Nov 2019 07:50:00 +0000 (09:50 +0200)]
selftests: forwarding: Add ethtool_lib.sh
Functions:
1. speeds_arr_get
The function returns an array of speed values from
/usr/include/linux/ethtool.h The array looks as follows:
[10baseT/Half] = 0,
[10baseT/Full] = 1,
...
2. ethtool_set:
params: cmd
The function runs ethtool by cmd (ethtool -s cmd) and checks if
there was an error in configuration
3. dev_speeds_get:
params: dev, with_mode (0 or 1), adver (0 or 1)
return value: Array of supported/Advertised link modes
with/without mode
Danielle Ratson [Mon, 18 Nov 2019 07:49:59 +0000 (09:49 +0200)]
selftests: mlxsw: Check devlink device before running test
The scale test for Spectrum-2 should only be invoked for Spectrum-2.
Skip the test otherwise.
Signed-off-by: Danielle Ratson <danieller@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Danielle Ratson [Mon, 18 Nov 2019 07:49:58 +0000 (09:49 +0200)]
selftests: mlxsw: Add router scale test for Spectrum-2
Same as for Spectrum-1, test the ability to add the maximum number of
routes possible to the switch.
Invoke the test from the 'resource_scale' wrapper script.
Signed-off-by: Danielle Ratson <danieller@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
page_pool: followup changes to restore tracepoint features
This patchset is a followup to Jonathan patch, that do not release
pool until inflight == 0. That changed page_pool to be responsible for
its own delayed destruction instead of relying on xdp memory model.
As the page_pool maintainer, I'm promoting the use of tracepoint to
troubleshoot and help driver developers verify correctness when
converting at driver to use page_pool. The role of xdp:mem_disconnect
have changed, which broke my bpftrace tools for shutdown verification.
With these changes, the same capabilities are regained.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
page_pool: extend tracepoint to also include the page PFN
The MM tracepoint for page free (called kmem:mm_page_free) doesn't provide
the page pointer directly, instead it provides the PFN (Page Frame Number).
This is annoying when writing a page_pool leak detector in BPF.
This patch change page_pool tracepoints to also provide the PFN.
The page pointer is still provided to allow other kinds of
troubleshooting from BPF.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
page_pool: add destroy attempts counter and rename tracepoint
When Jonathan change the page_pool to become responsible to its
own shutdown via deferred work queue, then the disconnect_cnt
counter was removed from xdp memory model tracepoint.
This patch change the page_pool_inflight tracepoint name to
page_pool_release, because it reflects the new responsability
better. And it reintroduces a counter that reflect the number of
times page_pool_release have been tried.
The counter is also used by the code, to only empty the alloc
cache once. With a stuck work queue running every second and
counter being 64-bit, it will overrun in approx 584 billion
years. For comparison, Earth lifetime expectancy is 7.5 billion
years, before the Sun will engulf, and destroy, the Earth.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
xdp: remove memory poison on free for struct xdp_mem_allocator
When looking at the details I realised that the memory poison in
__xdp_mem_allocator_rcu_free doesn't make sense. This is because the
SLUB allocator uses the first 16 bytes (on 64 bit), for its freelist,
which overlap with members in struct xdp_mem_allocator, that were
updated. Thus, SLUB already does the "poisoning" for us.
I still believe that poisoning memory make sense in other cases.
Kernel have gained different use-after-free detection mechanism, but
enabling those is associated with a huge overhead. Experience is that
debugging facilities can change the timing so much, that that a race
condition will not be provoked when enabled. Thus, I'm still in favour
of poisoning memory where it makes sense.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We currently match clause 45 PHYs using any ID read from a MMD marked
as present in the "Devices in package" registers 5 and 6. However,
this is incorrect. 45.2 says:
"The definition of the term package is vendor specific and could be
a chip, module, or other similar entity."
so a package could be more or less than the whole PHY - a PHY could be
made up of several modules instantiated onto a single chip such as the
Marvell 88x3310, or some of the MMDs could be disabled according to
chip configuration, such as the Broadcom 84881.
In the case of Broadcom 84881, the "Devices in package" registers
contain 0xc000009b, meaning that there is a PHYXS present in the
package, but all registers in MMD 4 return 0xffff. This leads to our
matching code incorrectly binding this PHY to one of our generic PHY
drivers.
This patch changes the way we determine whether to attempt to match a
MMD identifier, or use it to request a module - if the identifier is
all-ones, then we skip over it. When reading the identifiers, we
initialise phydev->c45_ids.device_ids to all-ones, only reading the
device ID if the "Devices in package" registers indicates we should.
This avoids the generic drivers incorrectly matching on a PHY ID of
0xffffffff.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 19 Nov 2019 00:56:13 +0000 (16:56 -0800)]
Merge branch 'Add-support-for-SFPs-behind-PHYs'
Russell King says:
====================
Add support for SFPs behind PHYs
This series adds partial support for SFP cages connected to PHYs,
specifically optical SFPs.
We add core infrastructure to phylib for this, and arrange for
minimal code in the PHY driver - currently, this is code to verify
that the module is one that we can support for Marvell 10G PHYs.
v2: add yaml binding patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Fri, 15 Nov 2019 19:56:56 +0000 (19:56 +0000)]
net: phy: marvell10g: add SFP+ support
Add support for SFP+ cages to the Marvell 10G PHY driver. This is
slightly complicated by the way phylib works in that we need to use
a multi-step process to attach the SFP bus, and we also need to track
the phylink state machine to know when the module's transmit disable
signal should change state.
With appropriate DT changes, this allows the SFP+ canges on the
Macchiatobin platform to be functional.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Fri, 15 Nov 2019 19:56:51 +0000 (19:56 +0000)]
net: phy: add core phylib sfp support
Add core phylib help for supporting SFP sockets on PHYs. This provides
a mechanism to inform the SFP layer about PHY up/down events, and also
unregister the SFP bus when the PHY is going away.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Fri, 15 Nov 2019 19:56:46 +0000 (19:56 +0000)]
dt-bindings: net: add ethernet controller and phy sfp property
Document the missing sfp property for ethernet controllers (which
has existed for some time) which is being extended to ethernet PHYs.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-kernels.git / log