David S. Miller [Thu, 3 Dec 2015 17:11:00 +0000 (12:11 -0500)]
Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2015-12-03
This series contains updates to i40e and i40evf only.
Mitch updates the i40evf driver by increasing the maximum number of queues,
since future devices will allow for more queue pairs. Cleans up a
duplicate printing of the driver info string done in init, since it is
already done in probe. Cleaned up the several allocations which did
not need to be at atomic level, where GFP_KERNEL would work just fine.
Then makes i40e_sync_vsi_filters() a more mature function, make having
a common exit point so it will properly release the busy lock on the VSI
and propagate errors to the callers. Then does some whitespace
housekeeping in i40evf.
Kiran moves and updates the detection/recovery of transmit queue hang code
to service_task from tx_timeout function. Also fixed memory leak when
users program flow-director filter using ethtool (sideband filter
programming), the cause being the check of 'tx_buffer->skb' was preventing
'raw_buf' from being freed as part of the cleanup.
Jesse enabled the ability to turn off/on packet split using ethtool priv
flags. Then does some housekeeping for both the i40e and i40evf drivers
which includes: remove unused/useless code, correct whitespace, remove
duplicate #include, fix incorrect comment, etc...
Neerav cleans up functions to gather Flow Control Rx XOFF stats, since
the recent change in the driver logic for checking transmit hang has been
moved, so these functions do not do anything meaningful any longer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patchset introduces the support of Ethernet SRIOV in ConnectX-4
family of 100G Ethernet NICs.
Some features are still missing, but all the basic SRIOV functionalities
are there already.
Basic Introduction:
ConnectX-4 HW architecture provides two kinds of underlying HW switches.
MPFS (Multi Physical Function Switch) or L2 Table in Software terms:
The HCA has one MPFS switch per physical port, this switch is responsible
of forwarding Unicast traffic to the various overlying Physical Functions (PFs).
Multicast traffic is flooded amongst all the PFs, Each PF can request to
forward a unicast MAC to its E-Switch Uplink vport (which we will cover later)
through SET_L2_TABLE_ENTRY HW command.
MPFS has five ports, four are connected to PFs (one for each) and one is connected
directly to the Physical Port (Physical Link).
E-Switch (Ethernet Switch):
The HCA has one per physical function. The main responsibility of this component is
to forward Unicast/Multicast and vlan tagged/untagged traffic to the various
Virtual Functions (VFs) allocated by the PF. Unlike MPFS, the PF needs to explicitly
create the E-Switch FDB table, Which is a HW flow table managed by the PF driver
whenever vport_group_manager capability bit is set for this PF.
E-Switch has Virtual Ports (vports) entities as its ports, vport0 and uplink vport
are special kind of vports that represents PF vport (vport0) and uplink vport which
is connected to the MPFS switch (if exists) as the PF external link.
vport1..vportN represent VF0..VF(N-1) egress/ingress ports.
E-Switch FDB contains forwarding rules such as:
UC MAC0 -> vport0(PF).
UC MAC1 -> vport1.
UC MAC2 -> vport2.
MC MACX -> vport0, vport2, Uplink.
MC MACY -> vport1, Uplink.
For unmatched traffic FDB has the following default rules:
Unmatched Traffic (src vport != Uplink) -> Uplink.
Unmatched Traffic (src vport == Uplink) -> vport0(PF).
NIC VPort context:
Each NIC (VF/PF) has its own vport context which will be used to store the current
NIC vport context (UC/MC and vlan lists) and other NIC properties such as MTU, promisc
mode, etc.. NIC (VF/PF) driver is responsible of constantly updating this context.
FDB rules population:
Each NIC vport (VF/PF) will notify E-Switch manager of its UC/MC vport
context changes via modify vport context command, which will be
translated to an event that will be handled by E-Switch manager (PF)
which will update FDB table accordingly.
Both PF and VF use the same driver and submit commands directly to the firmware.
The PF sees the vport_group_manager capability bit and as such runs the code
to populate the embedded switches as explained above.
The patch goes as follows:
Patches 1-2 introduces the basic PCI SRIOV functionalities and the support of
Connectx4 to enable specific VFs via enable/disable HCA commands. These two
patches will be also in use later for the IB SRIOV flow.
Patches 3-8 Introduces the basic E-Switch capabilities and commands to be used later by
VF to modify and update its NIC vport context, and by PF (E-Switch Manager) driver to
Query the VF NIC context and acts accordingly.
Patches 9-10 Provide the needed functionality of a NIC driver VF/PF to support SRIOV,
mainly vport context update support.
Patch 11 ("net/mlx5: Introducing E-Switch and l2 table"), Introduces the basic
E-Switch support and infrastructure to read vport context events and to update
MPFS L2 Table of the UC mac addresses request by the PF.
Patches 12-18 Introduces SRIOV enablemenet and E-Switch FDB table management
It adds the Basic E-Swtich public API to set and get sriov properties to be used
in PF netdev sriov ndos.
Patchset was applied ontop of commit 3f8c0f7 "gianfar: use of_property_read_bool()"
Saeed, Eli and Or.
changes from V0, addressed feedback from Alex Duyck:
- patch 09, remove the loop to seek the device address
- patch 09, avoid using array as returned value from helper function
- patch 10, fix possible buffer over-run
changes from V1, addressed feedback from and Julia Lawall and kbuild test robot
- patch 11 check the right variable for allocation failure
- patch 18 eliminated unneeded semicolon
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Tue, 1 Dec 2015 16:03:25 +0000 (18:03 +0200)]
net/mlx5e: Add support for SR-IOV ndos
Implement and enable SR-IOV ndos to manage SR-IOV configuration via
netdev netlink API.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Tue, 1 Dec 2015 16:03:24 +0000 (18:03 +0200)]
net/mlx5: E-Switch, Introduce get vf statistics
Add support to get VF statistics using query vport
counter command.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Tue, 1 Dec 2015 16:03:23 +0000 (18:03 +0200)]
net/mlx5: E-Switch, Introduce set vport vlan (VST mode)
Add query and modify functions to control client vlan and qos
striping or insertion, in E-Switch vports contexts.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Tue, 1 Dec 2015 16:03:22 +0000 (18:03 +0200)]
net/mlx5: E-Switch, Introduce HCA cap and E-Switch vport context
E-Switch vport context is unlike NIC vport context, managed by the
E-Switch manager or vport_group_manager and not by the NIC(VF) driver.
The E-Switch manager can access (read/modify) any of its vports
E-Switch context.
Currently E-Switch vport context includes only clietnt and server
vlan insertion and striping data (for later support of VST mode).
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Implement set VF mac/link state and query VF config
to be used later in nedev VF ndos or any other management API.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Tue, 1 Dec 2015 16:03:20 +0000 (18:03 +0200)]
net/mlx5: E-Switch, Add SR-IOV (FDB) support
Enabling E-Switch SRIOV for nvfs+1 vports.
Create E-Switch FDB for L2 UC/MC mac steering between VFs/PF and
external vport (Uplink).
FDB contains forwarding rules such as:
UC MAC0 -> vport0(PF).
UC MAC1 -> vport1.
UC MAC2 -> vport2.
MC MACX -> vport0, vport2, Uplink.
MC MACY -> vport1, Uplink.
For unmatched traffic FDB has the following default rules:
Unmached Traffic (src vport != Uplink) -> Uplink.
Unmached Traffic (src vport == Uplink) -> vport0(PF).
FDB rules population:
Each NIC vport (VF) will notify E-Switch manager of its UC/MC vport
context changes via modify vport context command, which will be
translated to an event that will be handled by E-Switch manager (PF)
which will update FDB table accordingly.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Define needed hardware structures and capabilities needed
for E-Switch FDB flow tables and read them on driver load.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Tue, 1 Dec 2015 16:03:18 +0000 (18:03 +0200)]
net/mlx5: Introducing E-Switch and l2 table
E-Switch is the software entity that represents and manages ConnectX4
inter-HCA ethernet l2 switching.
E-Switch has its own Virtual Ports, each Vport/vNIC/VF can be
connected to the device through a vport of an e-switch.
Each e-switch is managed by one vNIC identified by
HCA_CAP.vport_group_manager (usually it is the PF/vport[0]),
and its main responsibility is to forward each packet to the
right vport.
e-Switch needs to manage its own l2-table and FDB tables.
L2 table is a flow table that is managed by FW, it is needed for
Multi-host (Multi PF) configuration for inter HCA switching between
PFs.
FDB table is a flow table that is totally managed by e-Switch driver,
its main responsibility is to switch packets between e-Swtich internal
vports and uplink vport that belong to the same.
This patch introduces only e-Swtich l2 table management, FDB managemnt
will come later when ethernet SRIOV/VFs will be enabled.
preperation for ethernet sriov and l2 table management.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Tue, 1 Dec 2015 16:03:17 +0000 (18:03 +0200)]
net/mlx5e: Write vlan list into vport context
Each Vport/vNIC must notify underlying e-Switch layer
for vlan table changes in-order to update SR-IOV FDB tables.
We do that at vlan_rx_add_vid and vlan_rx_kill_vid ndos.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Tue, 1 Dec 2015 16:03:16 +0000 (18:03 +0200)]
net/mlx5e: Write UC/MC list and promisc mode into vport context
Each Vport/vNIC must notify underlying e-Switch layer
for UC/MC list and promisc mode updates, in-order to update
l2 tables and SR-IOV FDB tables.
We do that at set_rx_mode ndo.
preperation for ethernet-SRIOV and l2 table management.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Tue, 1 Dec 2015 16:03:15 +0000 (18:03 +0200)]
net/mlx5: Introduce access functions to modify/query vport vlans
Those functions are needed to notify the upcoming L2 table and SR-IOV
E-Switch(FDB) manager(PF), of the NIC vport (vf) vlan table changes.
preperation for ethernet sriov and l2 table management.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Tue, 1 Dec 2015 16:03:14 +0000 (18:03 +0200)]
net/mlx5: Introduce access functions to modify/query vport promisc mode
Those functions are needed to notify the upcoming SR-IOV
E-Switch(FDB) manager(PF), of the NIC vport (vf) promisc mode changes.
Preperation for ethernet sriov and l2 table management.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Tue, 1 Dec 2015 16:03:13 +0000 (18:03 +0200)]
net/mlx5: Introduce access functions to modify/query vport state
In preparation for SR-IOV we add here an API to enable each e-switch
manager (PF) to configure its VFs link states in e-switch
preparation for ethernet sriov.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Tue, 1 Dec 2015 16:03:12 +0000 (18:03 +0200)]
net/mlx5: Introduce access functions to modify/query vport mac lists
Those functions are needed to notify the upcoming L2 table and SR-IOV
E-Switch(FDB) manager(PF), of the NIC vport (vf) UC/MC mac lists
changes.
preperation for ethernet sriov and l2 table management.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Tue, 1 Dec 2015 16:03:11 +0000 (18:03 +0200)]
net/mlx5: Update access functions to Query/Modify vport MAC address
In preparation for SR-IOV we add here an API to enable each e-switch
client (PF/VF) to configure its L2 MAC addresses and for the e-switch
manager (usually the PF) to access them in order to be able to
configure them into the e-switch.
Therefore we now pass vport num parameter to
mlx5_query_nic_vport_context, so PF can access other vports contexts.
preperation for ethernet sriov and l2 table management.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Tue, 1 Dec 2015 16:03:10 +0000 (18:03 +0200)]
net/mlx5: Add HW capabilities and structs for SR-IOV E-Switch
Update HCA capabilities and HW struct to include needed
capabilities for upcoming Ethernet Switch (SR-IOV E-Switch).
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Cohen [Tue, 1 Dec 2015 16:03:09 +0000 (18:03 +0200)]
net/mlx5_core: Add base sriov support
This patch adds SRIOV base support for mlx5 supported devices. The same
driver is used for both PFs and VFs; VFs are identified by the driver
through the flag MLX5_PCI_DEV_IS_VF added to the pci table entries.
Virtual functions are created as usual through writing a value to the
sriov_numvs sysfs file of the PF device. Upon instantiating VFs, they will
all be probed by the driver on the hypervisor. One can gracefully unbind
them through /sys/bus/pci/drivers/mlx5_core/unbind.
mlx5_wait_for_vf_pages() was added to ensure that when a VF dies without
executing proper teardown, the hypervisor driver waits till all of the
pages that were allocated at the hypervisor to maintain its operation
are returned.
In order for the VF to be operational, the PF needs to call enable_hca
for it. This can be done before the VFs are created through a call to
pci_enable_sriov.
If the there are VFs assigned to a VMs when the driver of the PF is
unloaded, all the VF will experience system error and PF driver unloads
cleanly; in this case pci_disable_sriov is not called and the devices
will show when running lspci. Once the PF driver is reloaded, it will
sync its data structures which maintain state on its VFs.
Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Modify these functions to have func_id argument to state which device we
are referring to. This is done as a preparation for SRIOV support where
a PF driver needs to control its virtual functions.
Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarod Wilson [Mon, 30 Nov 2015 22:33:36 +0000 (17:33 -0500)]
alx: remove pointless assignment
Reasonably sure this doesn't serve any purpose.
CC: Jay Cliburn <jcliburn@gmail.com> CC: Chris Snook <chris.snook@gmail.com> CC: netdev@vger.kernel.org Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patchset introduces needed infrastructure for link aggregation
offload - for both team and bonding. It also implements the offload
in mlxsw driver.
Particulary, this patchset introduces possibility for upper driver
(bond/team/bridge/..) to pass type-specific info down to notifier listeners.
Info is passed along with NETDEV_CHANGEUPPER/NETDEV_PRECHANGEUPPER
notifiers. Listeners (drivers of netdevs being enslaved) can react
accordingly.
Other extension is for run-time use. This patchset introduces
new netdev notifier type - NETDEV_CHANGELOWERSTATE. Along with this
notification, the upper driver (bond/team/bridge/..) can pass some
information about lower device change, particulary link-up and
TX-enabled states. Listeners (drivers of netdevs being enslaved)
can react accordingly.
The last part of the patchset is implementation of LAG offload in mlxsw,
using both previously introduced infrastructre extensions.
Note that bond-speficic (and ugly) NETDEV_BONDING_INFO used by mlx4
can be removed and mlx4 can use the extensions this patchset adds.
I plan to convert it and get rid of NETDEV_BONDING_INFO in
a follow-up patchset.
v2->v3:
- one small fix in patch 1
v1->v2:
- added patch 1 and 2 per Andy's request
- couple of more or less cosmetic changes described in couple other patches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 3 Dec 2015 11:12:29 +0000 (12:12 +0100)]
mlxsw: spectrum: Implement FDB add/remove/dump for LAG
Implement FDB offloading for lagged ports, including learning LAG FDB
entries, adding/removing static FDB entries and dumping existing LAG FDB
entries.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 3 Dec 2015 11:12:23 +0000 (12:12 +0100)]
mlxsw: core: Add support for packets received from LAG port
Lower layer (pci) has information if the packet is received via LAG port.
If that is the case, it fills up rx_info accordingly. However upper
layer does not care about lag_id/port_index for received packets so
convert it to local_port before passing it up. For that conversion, lag
mapping array is introduced. Upper layer is responsible for setting up
the mapping according to what is set in HW.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 3 Dec 2015 11:12:21 +0000 (12:12 +0100)]
bonding: set inactive flags on release
Be correct and symmetric to enslave and set inactive flags during release.
That gives LAG offload drivers - lower state change listeners - possibility
to do proper cleanup.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 3 Dec 2015 11:12:19 +0000 (12:12 +0100)]
bonding: allow notifications for bond_set_slave_link_state
Similar to state notifications.
We allow caller to indicate if the notification should happen now or later,
depending on if he holds rtnl mutex or not. Introduce bond_slave_link_notify
function (similar to bond_slave_state_notify) which is later on called
with rtnl mutex and goes over slaves and executes delayed notification.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 3 Dec 2015 11:12:15 +0000 (12:12 +0100)]
net: introduce change lower state notifier
When lower device like bonding slave, team/bridge port, etc changes its
state, it is useful for others to notice this change. Currently this is
implemented specificly for bonding as NETDEV_BONDING_INFO notifier. This
patch aims to replace this specific usage and make this more generic to
be used for all upper-lower devices.
Introduce NETDEV_CHANGELOWERSTATE netdev notifier type and
netdev_lower_state_changed() helper.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 3 Dec 2015 11:12:14 +0000 (12:12 +0100)]
bonding: fill-up LAG changeupper info struct and pass it along
Initialize netdev_lag_upper_info structure by TX type according to
current bonding mode and pass it along via netdev_master_upper_dev_link.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 3 Dec 2015 11:12:11 +0000 (12:12 +0100)]
net: add possibility to pass information about upper device via notifier
Sometimes the drivers and other code would find it handy to know some
internal information about upper device being changed. So allow upper-code
to pass information down to notifier listeners during linking.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 3 Dec 2015 11:12:04 +0000 (12:12 +0100)]
net: Add support for CHANGEUPPER notifier error injection
Since CHANGEUPPER can now fail, add support for it in the newly
introduced netdev notifier error injection infrastructure.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 3 Dec 2015 11:12:03 +0000 (12:12 +0100)]
net: Check CHANGEUPPER notifier return value
switchdev drivers reflect the newly requested topology to hardware when
CHANGEUPPER is received, after software links were already formed.
However, the operation can fail and user will not be notified, as the
return value of the notifier is not checked.
Add this check and rollback software links if necessary.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Thu, 3 Dec 2015 12:20:57 +0000 (04:20 -0800)]
i40e: Fix i40e_print_features() VEB mode output
Commit 7fd89545f337 ("i40e: remove BUG_ON from feature string building")
added defective output when I40E_FLAG_VEB_MODE_ENABLED was set in
function i40e_print_features.
Fix it.
Miscellanea:
- Remove unnecessary string variable
- Add space before not after fixed strings
- Use kmalloc not kzalloc
- Don't initialize i to 0, use result of first snprintf
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 3 Dec 2015 16:43:32 +0000 (11:43 -0500)]
Merge branch '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-12-03
This series contains updates to ixgbe and ixgbevf only.
Mark cleans up ixgbe_init_phy_ops_x550em, since this was designed to
initialize function pointers only and moves the KR PHY reset to the
ixgbe_setup_internal_phy_t_x550em which was designed to detect which
mode the PHY operates in and set it up. Added the new thermal alarm
type support used with newer X550EM_x devices. Fixed both ixgbe and
ixgbevf to use a private work queue to avoid hangs, which would
possibly occur when creating and destroying many VFS repeatedly.
Updated ixgbe PTP implementation to accommodate X550EM_x devices,
which handle clocking differently. Fixed specification violations
in the datasheet, which was reported by Dan Streetman. Fixed ixgbe
to check for and handle IPv6 extended headers so that Tx checksum
offload can be done, which was reported by Tom Herbert. Fixed ixgbe
link issue for some systems with X540 or X550 by only inhibiting the
turning PHY power off when manageability is present.
Alex Duyck refactors the MAC address configuration code, which in
turns fixes an issue where once 63 entries had been used, you could no
longer add additional filters. Updated ixgbe to use __dev_uc_sync
which also resolved an issue in which you could not remove an FDB
address without having to reset the port. Updated the ixgbe driver
to make use of all the free RAR entries for FDB use if needed.
v2: updated patch 13 to "Alex Duyck Approved" version, in the original
submission, I had grabbed a previous version of the patch and did not
catch it was superseded by a later version
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Rustad [Thu, 19 Nov 2015 21:56:30 +0000 (13:56 -0800)]
ixgbevf: Handle extended IPv6 headers in Tx path
Check for and handle IPv6 extended headers so that Tx checksum
offload can be done. Also use skb_checksum_help for unexpected
cases. Thanks to Tom Herbert for noticing these problems. Thanks
to Alexander Duyck for seeing how to coalesce the error handling
into one location.
Reported-by: Tom Herbert <tom@herbertland.com> Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Thu, 5 Nov 2015 19:02:14 +0000 (11:02 -0800)]
ixgbe: Always turn PHY power on when requested
Instead of inhibiting PHY power control when manageability is
present, only inhibit turning PHY power off when manageability
is present. Consequently, PHY power will always be turned on when
requested. Without this patch, some systems with X540 or X550
devices in some conditions will never get link.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Wed, 18 Nov 2015 17:21:28 +0000 (09:21 -0800)]
ixgbe: Handle extended IPv6 headers in Tx path
Check for and handle IPv6 extended headers so that Tx checksum
offload can be done. Also use skb_checksum_help for unexpected
cases. Thanks to Tom Herbert for noticing these problems. Thanks
to Alexander Duyck for recognizing problems with the first version
of this patch and recognizing how to coalesce error conditions
into a single location.
Reported-by: Tom Herbert <tom@herbertland.com> Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Fri, 30 Oct 2015 22:29:34 +0000 (15:29 -0700)]
ixgbe: Save VF info and take references
Save VF device pointers and take references to speed accesses used
to monitor the device behavior to avoid slot resets. The saved
information avoids lock contention during the search used to access
each of the VFs.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Tue, 27 Oct 2015 20:23:23 +0000 (13:23 -0700)]
ixgbe: Wait for master disable to be set
According to the datasheets, the driver should wait for the master
disable bit to read as being set before checking the status
register for master disable.
Reported-by: Dan Streetman <dan.streetman@canonical.com> Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Tue, 27 Oct 2015 20:23:14 +0000 (13:23 -0700)]
ixgbe: Correct spec violations by waiting after reset
The ixgbe driver was violating the specification in the datasheet
by not waiting 1ms before checking for the reset bit clearing. This
is called out for devices supported by ixgbe, so implement the
required delay.
Reported-by: Dan Streetman <dan.streetman@canonical.com> Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Tue, 27 Oct 2015 16:58:07 +0000 (09:58 -0700)]
ixgbe: Update PTP to support X550EM_x devices
The X550EM_x devices handle clocking differently, so update the
PTP implementation to accommodate them. This involves significant
changes to ixgbe's PTP code to accommodate the new range of
behaviors including things like non-power-of-2 clock wrapping.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Thu, 22 Oct 2015 23:26:42 +0000 (16:26 -0700)]
ixgbe: Allow FDB entries access to more RAR filters
This change makes it so that we allow the PF to make use of all free RAR
entries for FDB use if needed.
Previously the code limited us to 16 unicast entries, however this was
shared between MACVLAN which wasn't limited and the FDB code which was. So
instead of treating the FDB code as a second class citizen I have updated
it so that it has access to just as many entries as the MACVLAN filters.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Thu, 22 Oct 2015 23:26:36 +0000 (16:26 -0700)]
ixgbe: Use __dev_uc_sync and __dev_uc_unsync for unicast addresses
This change replaces the ixgbe_write_uc_addr_list call in ixgbe_set_rx_mode
with a call to __dev_uc_sync instead. This works much better with the MAC
addr list code that was already in place and solves an issue in which you
couldn't remove an FDB address without having to reset the port.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Thu, 22 Oct 2015 23:26:30 +0000 (16:26 -0700)]
ixgbe: Refactor MAC address configuration code
In the process of tracking down a memory leak when adding/removing FDB
entries I had to go through the MAC address configuration code for ixgbe.
In the process of doing so I found a number of issues that impacted
readability and performance. This change updates the code in general to
clean it up so it becomes clear what each step is doing. From what I can
tell there a couple of bugs cleaned up in this code.
First is the fact that the MAC addresses were being double counted for the
PF. As a result once entries up to 63 had been used you could no longer
add additional filters.
A simple test case for this:
for i in `seq 0 96`
do
ip link add link ens8 name mv$i type macvlan
ip link set dev mv$i up
done
When things are working correctly RAL/H registers 1 - 97 will be consumed.
In the failing case it will stop at 63 and prevent any further filters from
being added.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Thu, 22 Oct 2015 00:21:20 +0000 (17:21 -0700)]
ixgbevf: Minor cleanups
Make some minor cleanups, such as simplifying return paths, deleting
unneeded initializations, return values more directly and so forth.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Thu, 22 Oct 2015 00:21:15 +0000 (17:21 -0700)]
ixgbevf: Use a private workqueue to avoid certain possible hangs
Use a private workqueue to avoid hangs that were otherwise possible
when performing stress tests, such as creating and destroying many
VFS repeatedly.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Thu, 22 Oct 2015 00:21:10 +0000 (17:21 -0700)]
ixgbe: Use private workqueue to avoid certain possible hangs
Use a private workqueue to avoid hangs that were otherwise possible
when performing stress tests, such as creating and destroying many
VFS repeatedly.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Mon, 19 Oct 2015 16:22:14 +0000 (09:22 -0700)]
ixgbe: Add support for newer thermal alarm
The newer copper PHY implementation used with newer X550EM_x
devices uses a different thermal alarm type than the earlier
one. Make changes to support both types.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Fri, 16 Oct 2015 20:27:49 +0000 (13:27 -0700)]
ixgbe: Prevent KR PHY reset in ixgbe_init_phy_ops_x550em
This patch removes KR PHY reset from ixgbe_init_phy_ops_x550em,
since this function is meant to initialize function pointers for
the detected PHY type. Internal PHY reset was moved to
ixgbe_setup_internal_phy_t_x550em which will now detect which
mode the internal PHY operates in and set it up as required.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jesse Brandeburg [Thu, 19 Nov 2015 01:35:42 +0000 (17:35 -0800)]
i40e: trivial fixes
1) remove duplicate include of tcp.h
2) put an ampersand at the end of a line instead of the beginning
3) remove a useless dev_info
4) match declaration of function to the implementation
5) repair incorrect comment
6) correct whitespace
7) remove unused define
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Fri, 6 Nov 2015 23:26:11 +0000 (15:26 -0800)]
i40e/i40evf: use logical operator
We shouldn't be using a bitwise operator here; it's not a bitwise
operation. Use a logical operator instead. Why doesn't c have a
logical-or-and-assign operator?
Change-ID: Id84f3ca884910bed7073c84b1e16a102e958d0de Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Fri, 6 Nov 2015 23:26:10 +0000 (15:26 -0800)]
i40e: fix whitespace
Operators should have spaces around them.
Change-ID: I64735e9aa8618b9a5059a87ace1c999d6d3bfcfb Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Neerav Parikh [Fri, 6 Nov 2015 23:26:09 +0000 (15:26 -0800)]
i40e: Remove separate functions gathering XOFF Rx stats
The separate functions to gather Flow control Rx XOFF stats was to
determine if the Tx for a queue was paused due to Link Flow Control(LFC)
or Priority Flow Control(PFC).
But, with recent change in the i40e driver the logic for checking th Tx
hang has been removed and these functions don't do anything meaningful.
Hence, there is no need to keep these separate functions to gather Rx
XOFF stats for LFC or PFC.
This patch removes these functions and moves the stat collection for
XOFF Rx to the i40e_update_pf_stats() that collects all the PF stats.
Change-ID: Iec1452dac3a6766f0d968e754cb407530d7c60cd Signed-off-by: Neerav Parikh <neerav.parikh@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ethtool priv flags implementation to enable or disable packet split, which
is a hardware feature that inspects headers and will put headers in a
separate DMA buffer from the payload data. The driver was automatically
choosing to enable packet split in some cases and this gives the user the
ability to turn it off/on explicitly.
to query state:
ethtool --show-priv-flags ethx
to enable:
ethtool --set-priv-flags ethx packet-split on
to disable:
ethtool --set-priv-flags ethx packet-split off
Why would anyone want this?
Because some environments benefit from header/data split in the receive
buffer, and the driver defaults to one or the other depending on
environment/kernel parameters.
Why didn't you implement a generic ethtool control for this feature?
Because Intel hardware is the only hardware that supports header/data
split.
Change-ID: I803121e1eecc9ccb2884031fd85dd1110b3af66d Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Fri, 6 Nov 2015 23:26:06 +0000 (15:26 -0800)]
i40evf: use correct types
Don't use uint32_t type the kernel. Use u32 instead. No functional
change.
Change-ID: I77bbf3b6464edaef747c7104b43534032a4dba63 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Mon, 9 Nov 2015 23:35:50 +0000 (15:35 -0800)]
i40e: propagate properly
i40e_sync_vsi_filters() is the surly teenager of this driver. It says
it's going to report errors, but it doesn't actually do that most of the
time. And when it does, it leaves a mess.
Change this function to have a common exit point so it will properly
release the busy lock on the VSI. Propagate errors to the callers.
Finally, adjust a few callers to check for and deal with errors from
this function.
Change-ID: Ic6af4956491e72402ebb3c538a3c31a0ad7f8667 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Fri, 6 Nov 2015 23:26:04 +0000 (15:26 -0800)]
i40evf: don't use atomic allocation
These allocations don't need to be at atomic level. GFP_KERNEL is fine
and they'll reduce stress on the allocator when the system is starved
for memory.
Change-ID: I3561d0399a681de0ad25291b6c848b224c1fde12 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the memory leak which would be seen otherwise when user
programs flow-director filter using ethtool (sideband filter programming).
When ethtool is used to program flow directory filter, 'raw_buf' gets
allocated and it is supposed to be freed as part of queue cleanup. But
check of 'tx_buffer->skb' was preventing it from being freed.
Change-ID: Ief4f0a1a32a653180498bf6e987c1b4342ab8923 Signed-off-by: Kiran Patil <kiran.patil@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Kiran Patil [Fri, 6 Nov 2015 23:26:02 +0000 (15:26 -0800)]
i40e: Detection and recovery of TX queue hung logic moved to service_task from tx_timeout
This patch contains following changes:
- detection and recovery logic (issue SW interrupt) has been moved to
service_task from timeout function.
- added some more debug info from tx_timeout.
Logic to detect and recover TX queue hung is now two step process:
- service_task detects TX queue hung and sets a bit(hung_detected) if
it was not set.
- if bit was set (means this is back-back hung condition detected),
issue SW interrupt and clear the bit.
- napi_poll clears the bit unconditionally since it cleans TX/RX queues.
Change-ID: Ieed03a48927c845a988b3ff375090bf37caeb903 Signed-off-by: Kiran Patil <kiran.patil@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Fri, 6 Nov 2015 23:26:01 +0000 (15:26 -0800)]
i40evf: remove duplicate string
We already print the driver info string in probe, so don't print
it again in init. No need to repeat. No need to repeat.
Change-ID: Ief597997f580a8c54d5950e3a84c29f2075be66b Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Fri, 6 Nov 2015 23:26:00 +0000 (15:26 -0800)]
i40evf: set real num queues
Use the helper function to set the real number of RX queues, and also
set the real number of TX queues.
Change-ID: I67982799de3f248fb4158ccdc9b1a74385f42ddd Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Fri, 6 Nov 2015 23:25:59 +0000 (15:25 -0800)]
i40evf: increase max number of queues
Future devices will allow for more queue pairs, so allocate a netdev
that can handle them. While we're at it, get rid of the separate
MAX_TX/MAX_RX defines. Since we always get matched queue pairs, having
these makes no sense.
Change-ID: I0e3556cd9a962506e509eb7c0afa36b329e8cb51 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jarod Wilson [Mon, 30 Nov 2015 22:12:21 +0000 (17:12 -0500)]
sfc: use ALIGN macro for aligning frame sizes
Don't open-code it.
CC: Solarflare linux maintainers <linux-net-drivers@solarflare.com> CC: Shradha Shah <sshah@solarflare.com> CC: netdev@vger.kernel.org Signed-off-by: Jarod Wilson <jarod@redhat.com> Acked-by: Bert Kenward <bkenward@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 30 Nov 2015 16:57:28 +0000 (08:57 -0800)]
tcp: suppress too verbose messages in tcp_send_ack()
If tcp_send_ack() can not allocate skb, we properly handle this
and setup a timer to try later.
Use __GFP_NOWARN to avoid polluting syslog in the case host is
under memory pressure, so that pertinent messages are not lost under
a flood of useless information.
sk_gfp_atomic() can use its gfp_mask argument (all callers currently
were using GFP_ATOMIC before this patch)
We rename sk_gfp_atomic() to sk_gfp_mask() to clearly express this
function now takes into account its second argument (gfp_mask)
Note that when tcp_transmit_skb() is called with clone_it set to false,
we do not attempt memory allocations, so can pass a 0 gfp_mask, which
most compilers can emit faster than a non zero or constant value.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 3 Dec 2015 04:43:48 +0000 (23:43 -0500)]
Merge branch 'hv_netvsc-less-headroom'
Merge branch 'hv_netvsc-less-headroom'
K. Y. Srinivasan says:
====================
hv_netvsc: Eliminate the additional head room
In an attempt to avoid having to allocate memory on the send path, the netvsc
driver was requesting additional head room so that both rndis header and the
netvsc packet (the state that had to persist) could be placed in the skb.
Since the amount of head room requested was exceeding the default head room
as set in LL_MAX_HEADER, we were forcing a reallocation of skb.
With this patch-set, I have reduced the size of the netvsc packet to less
than 20 bytes and with this reduction we don't need to ask for any additional
headroom. We place the rndis header in the skb head room and we place the
netvsc packet in control buffer area in the skb.
V2: - Addressed review comments:
- Eliminated more fields from netvsc packet structure.
V3: - Fixed a typo in patch: hv_netvsc: Don't ask for additional head room in the skb.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Wed, 2 Dec 2015 00:43:13 +0000 (16:43 -0800)]
hv_netvsc: Eliminate page_buf from struct hv_netvsc_packet
Eliminate page_buf from struct hv_netvsc_packet.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Packet scheduler guarantees there won't be multiple senders for the same
queue and as we use q_idx for multi_send_data the spinlock is redundant.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
hv_netvsc: move subchannel existence check to netvsc_select_queue()
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Wed, 2 Dec 2015 00:43:10 +0000 (16:43 -0800)]
hv_netvsc: Don't ask for additional head room in the skb
The rndis header is 116 bytes big and can be placed in the default
head room that will be available in the skb. Since the netvsc packet
is less than 48 bytes, we can use the skb control buffer
for the netvsc packet. With these changes we don't need to
ask for additional head room.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Wed, 2 Dec 2015 00:43:09 +0000 (16:43 -0800)]
hv_netvsc: Eliminate send_completion_ctx from struct hv_netvsc_packet
Eliminate send_completion_ctx from struct hv_netvsc_packet.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Wed, 2 Dec 2015 00:43:08 +0000 (16:43 -0800)]
hv_netvsc: Eliminate send_completion from struct hv_netvsc_packet
Eliminate send_completion from struct hv_netvsc_packet.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Wed, 2 Dec 2015 00:43:07 +0000 (16:43 -0800)]
hv_netvsc: Eliminatte the data field from struct hv_netvsc_packet
Eliminatte the data field from struct hv_netvsc_packet.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Wed, 2 Dec 2015 00:43:06 +0000 (16:43 -0800)]
hv_netvsc: Eliminate rndis_msg pointer from hv_netvsc_packet structure
Eliminate rndis_msg pointer from hv_netvsc_packet structure.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Wed, 2 Dec 2015 00:43:05 +0000 (16:43 -0800)]
hv_netvsc: Eliminate the channel field in hv_netvsc_packet structure
Eliminate the channel field in hv_netvsc_packet structure.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-focal-kernel.git / log