Barak Witkowski [Wed, 7 Dec 2011 03:45:36 +0000 (03:45 +0000)]
bnx2x: fix typo in fcoe stats collection
Signed-off-by: Barak Witkowski <barak@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Various bugfixes for caif_shmcore.c:
- fix deadlocks due to improper usage of spin-lock
- add missing spin-lock init
- don't call dev_kfree_skb() with irqs disabled,
use dev_kfree_skb_irq() instead.
- fix potential skb null pointer de-reference.
Squashed original patches from:
Rabin Vincent <rabin.vincent@stericsson.com>
Durga Prasada Rao BATHINA <durgaprasadarao.b@stericcson.com>
Arun Murthy <arun.murthy@stericsson.com>
Bibek Basu <bibek.basu@stericsson.com>
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Christian Auby [Tue, 6 Dec 2011 12:15:41 +0000 (12:15 +0000)]
caif-hsi: Remove wake line modification when flushing FIFO
Raising wake before flushing FIFO and lowering it after caused a
spike on AC wake that were sometimes detected and acted upon by the
modem. Fixed this by remove wake line modification when flushing FIFO.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Tue, 6 Dec 2011 10:58:08 +0000 (10:58 +0000)]
bnx2x: Fix compile errors if CONFIG_CNIC is not set
Don't provide FCoE and iSCSI statistics to management firmware if
CONFIG_CNIC is not set. Some needed structure fields are not defined
without CONFIG_CNIC.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: Silence seq_scale() unused warning
ipv4:correct description for tcp_max_syn_backlog
pasemi_mac: Fix building as module
netback: Fix alert message.
r8169: fix Rx index race between FIFO overflow recovery and NAPI handler.
r8169: Rx FIFO overflow fixes.
ipv4: Fix peer validation on cached lookup.
ipv4: make sure RTO_ONLINK is saved in routing cache
iwlwifi: change the default behavior of watchdog timer
iwlwifi: do not re-configure HT40 after associated
iwlagn: fix HW crypto for TX-only keys
Revert "mac80211: clear sta.drv_priv on reconfiguration"
mac80211: fill rate filter for internal scan requests
cfg80211: amend regulatory NULL dereference fix
cfg80211: fix race on init and driver registration
Linus Torvalds [Tue, 6 Dec 2011 19:54:33 +0000 (11:54 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ftrace: Fix hash record accounting bug
perf: Fix parsing of __print_flags() in TP_printk()
jump_label: jump_label_inc may return before the code is patched
ftrace: Remove force undef config value left for testing
tracing: Restore system filter behavior
tracing: fix event_subsystem ref counting
Pavel Emelyanov [Tue, 6 Dec 2011 07:59:52 +0000 (07:59 +0000)]
sock_diag: Move the sock_ code to net/core/
This patch moves the sock_ code from inet_diag.c to generic sock_diag.c
file and provides necessary request_module-s calls and a pointer on
inet_diag_compat dumping routine.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Tue, 6 Dec 2011 07:59:32 +0000 (07:59 +0000)]
inet_diag: Cleanup type2proto last user
Now all the code works with sock_diag_req-compatible structs, so it's
possible to stop using the inet_diag_type2proto in inet_csk_diag_fill.
Pass the inet_diag_req into it and use the sdiag_protocol field. At the
same time remove the explicit ext argument, since it's also on the req.
However, this conversion is still required in _compat code, so just move
this routine, not remove.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Tue, 6 Dec 2011 07:56:43 +0000 (07:56 +0000)]
inet_diag: Partly rename inet_ to sock_
The ultimate goal is to get the sock_diag module, that works in
family+protocol terms. Currently this is suitable to do on the
inet_diag basis, so rename parts of the code. It will be moved
to sock_diag.c later.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Tue, 6 Dec 2011 02:05:12 +0000 (02:05 +0000)]
bnx2x: fix crash while ethtool -t
commit 2df1a70aaf70e8dff11b89b938a5f317556ee640 "bnx2x: Support
for byte queue limits" has introduced an asymmetry in usage of
netdev_tx_completed_queue and netdev_tx_sent_queue. Missing
call to netdev_tx_sent_queue causes the crash during ethtool -t.
The patch adds the missing call.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Liu [Tue, 6 Dec 2011 00:08:20 +0000 (00:08 +0000)]
netback: remove redundant assignment
New value for netbk->mmap_pages[pending_idx] is assigned in
xen_netbk_alloc_page(), no need for a second assignment which
exposes internal to the outside world.
Signed-off-by: Wei Liu <wei.liu2@citrix.com> Acked-by: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Barak Witkowski [Mon, 5 Dec 2011 22:41:50 +0000 (22:41 +0000)]
bnx2x, cnic: support DRV_INFO upon FW request
Add support to send driver capabilities, settings and statistics to
management firmware.
[ Redone using many local variables, removed many unnecessary inlines,
and put #defines at the left margin suggested by Joe Perches ]
Signed-off-by: Barak Witkowski <barak@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: Eddie Wai <eddie.wai@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Barak Witkowski [Mon, 5 Dec 2011 21:52:23 +0000 (21:52 +0000)]
bnx2x: add fcoe statistics
Add FCoE statistics support for FCoE capable devices.
Signed-off-by: Barak Witkowski <barak@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Barak Witkowski [Mon, 5 Dec 2011 21:52:22 +0000 (21:52 +0000)]
bnx2x: add PFC statistics
Add Priority flow control counters for ethtool -S.
Signed-off-by: Barak Witkowski <barak@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Pan(潘卫平) [Mon, 5 Dec 2011 21:39:41 +0000 (21:39 +0000)]
ipv4:correct description for tcp_max_syn_backlog
Since commit c5ed63d66f24(tcp: fix three tcp sysctls tuning),
sysctl_max_syn_backlog is determined by tcp_hashinfo->ehash_mask,
and the minimal value is 128, and it will increase in proportion to the
memory of machine.
The original description for tcp_max_syn_backlog and sysctl_max_syn_backlog
are out of date.
Changelog:
V2: update description for sysctl_max_syn_backlog
Signed-off-by: Weiping Pan <panweiping3@gmail.com> Reviewed-by: Shan Wei <shanwei88@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Mon, 5 Dec 2011 19:44:22 +0000 (19:44 +0000)]
pasemi_mac: Fix building as module
Commit ded19addf9c937d83b9bfb4d73a836732569041b ('pasemic_mac*: Move
the PA Semi driver') inadvertently split pasemi_mac into two separate
modules with unresolved symbols. Change it back into a single module.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 6 Dec 2011 00:54:15 +0000 (16:54 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
intr_remapping: Fix section mismatch in ir_dev_scope_init()
intel-iommu: Fix section mismatch in dmar_parse_rmrr_atsr_dev()
x86, amd: Fix up numa_node information for AMD CPU family 15h model 0-0fh northbridge functions
x86, AMD: Correct align_va_addr documentation
x86/rtc, mrst: Don't register a platform RTC device for for Intel MID platforms
x86/mrst: Battery fixes
x86/paravirt: PTE updates in k(un)map_atomic need to be synchronous, regardless of lazy_mmu mode
x86: Fix "Acer Aspire 1" reboot hang
x86/mtrr: Resolve inconsistency with Intel processor manual
x86: Document rdmsr_safe restrictions
x86, microcode: Fix the failure path of microcode update driver init code
Add TAINT_FIRMWARE_WORKAROUND on MTRR fixup
x86/mpparse: Account for bus types other than ISA and PCI
x86, mrst: Change the pmic_gpio device type to IPC
mrst: Added some platform data for the SFI translations
x86,mrst: Power control commands update
x86/reboot: Blacklist Dell OptiPlex 990 known to require PCI reboot
x86, UV: Fix UV2 hub part number
x86: Add user_mode_vm check in stack_overflow_check
Linus Torvalds [Tue, 6 Dec 2011 00:54:00 +0000 (16:54 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix loss of notification with multi-event
perf, x86: Force IBS LVT offset assignment for family 10h
perf, x86: Disable PEBS on SandyBridge chips
trace_events_filter: Use rcu_assign_pointer() when setting ftrace_event_call->filter
perf session: Fix crash with invalid CPU list
perf python: Fix undefined symbol problem
perf/x86: Enable raw event access to Intel offcore events
perf: Don't use -ENOSPC for out of PMU resources
perf: Do not set task_ctx pointer in cpuctx if there are no events in the context
perf/x86: Fix PEBS instruction unwind
oprofile, x86: Fix crash when unloading module (nmi timer mode)
oprofile: Fix crash when unloading module (hr timer mode)
Linus Torvalds [Tue, 6 Dec 2011 00:53:43 +0000 (16:53 -0800)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clockevents: Set noop handler in clockevents_exchange_device()
tick-broadcast: Stop active broadcast device when replacing it
clocksource: Fix bug with max_deferment margin calculation
rtc: Fix some bugs that allowed accumulating time drift in suspend/resume
rtc: Disable the alarm in the hardware
Linus Torvalds [Tue, 6 Dec 2011 00:50:24 +0000 (16:50 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched, x86: Avoid unnecessary overflow in sched_clock
sched: Fix buglet in return_cfs_rq_runtime()
sched: Avoid SMT siblings in select_idle_sibling() if possible
sched: Set the command name of the idle tasks in SMP kernels
sched, rt: Provide means of disabling cross-cpu bandwidth sharing
sched: Document wait_for_completion_*() return values
sched_fair: Fix a typo in the comment describing update_sd_lb_stats
sched: Add a comment to effective_load() since it's a pain
Linus Torvalds [Mon, 5 Dec 2011 23:35:16 +0000 (15:35 -0800)]
Merge branch 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] ap: Setup timer for sending messages after reset.
[S390] cio: fix chsc_chp_vary
[S390] cio: provide fake irb for transport mode IO
[S390] cio: disallow driver io for known to be broken paths
[S390] hibernate: directly trigger subchannel evaluation
[S390] remove reset of system call restart on psw changes
[S390] add missing .set function for NT_S390_LAST_BREAK regset
[S390] fix page change underindication in pgste_update_all
[S390] ptrace inferior call interactions with TIF_SYSCALL
[S390] kdump: Replace is_kdump_kernel() with OLDMEM_BASE check
françois romieu [Sun, 4 Dec 2011 20:30:52 +0000 (20:30 +0000)]
r8169: fix Rx index race between FIFO overflow recovery and NAPI handler.
Since 92fc43b4159b518f5baae57301f26d770b0834c9, rtl8169_tx_timeout ends up
resetting Rx and Tx indexes and thus racing with the NAPI handler via
-> rtl8169_hw_reset
-> rtl_hw_reset
-> rtl8169_init_ring_indexes
What about returning to the original state ?
rtl_hw_reset is only used by rtl8169_hw_reset and rtl8169_init_one.
The latter does not need rtl8169_init_ring_indexes because the indexes
still contain their original values from the newly allocated network
device private data area (i.e. 0).
rtl8169_hw_reset is used by:
1. rtl8169_down
Helper for rtl8169_close. rtl8169_open explicitely inits the indexes
anyway.
2. rtl8169_pcierr_interrupt
Indexes are set by rtl8169_reinit_task.
3. rtl8169_interrupt
rtl8169_hw_reset is needed when the device goes down. See 1.
4. rtl_shutdown
System shutdown handler. Indexes are irrelevant.
5. rtl8169_reset_task
Indexes must be set before rtl_hw_start is called.
6. rtl8169_tx_timeout
Indexes should not be set. This is the job of rtl8169_reset_task anyway.
The removal of rtl8169_hw_reset in rtl8169_tx_timeout and its move in
rtl8169_reset_task do not change the analysis.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Cc: hayeswang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
françois romieu [Sun, 4 Dec 2011 20:30:45 +0000 (20:30 +0000)]
r8169: Rx FIFO overflow fixes.
Realtek has specified that the post 8168c gigabit chips and the post
8105e fast ethernet chips recover automatically from a Rx FIFO overflow.
The driver does not need to clear the RxFIFOOver bit of IntrStatus and
it should rather avoid messing it.
The implementation deserves some explanation:
1. events outside of the intr_event bit mask are now ignored. It enforces
a no-processing policy for the events that either should not be there
or should be ignored.
2. RxFIFOOver was already ignored in rtl_cfg_infos[RTL_CFG_1] for the
whole 8168 line of chips with two exceptions:
- RTL_GIGA_MAC_VER_22 since b5ba6d12bdac21bc0620a5089e0f24e362645efd
("use RxFIFO overflow workaround for 8168c chipset.").
This one should now be correctly handled.
- RTL_GIGA_MAC_VER_11 (8168b) which requires a different Rx FIFO
overflow processing.
Though it does not conform to Realtek suggestion above, the updated
driver includes no change for RTL_GIGA_MAC_VER_12 and RTL_GIGA_MAC_VER_17.
Both are 8168b. RTL_GIGA_MAC_VER_12 is common and a bit old so I'd rather
wait for experimental evidence that the change suggested by Realtek really
helps or does not hurt in unexpected ways.
Removed case statements in rtl8169_interrupt are only 8168 relevant.
3. RxFIFOOver is masked for post 8105e 810x chips, namely the sole 8105e
(RTL_GIGA_MAC_VER_30) itself.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Cc: hayeswang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 4 Dec 2011 08:51:08 +0000 (08:51 +0000)]
tcp: fix tcp_trim_head()
commit f07d960df3 (tcp: avoid frag allocation for small frames)
breaked assumption in tcp stack that skb is either linear (skb->data_len
== 0), or fully fragged (skb->data_len == skb->len)
tcp_trim_head() made this assumption, we must fix it.
Thanks to Vijay for providing a very detailed explanation.
Reported-by: Vijay Subramanian <subramanian.vijay@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
caif: Stash away hijacked skb destructor and call it later
This patch adds functionality for avoiding orphaning SKB too early.
The original skb is stashed away and the original destructor is called
from the hi-jacked flow-on callback. If CAIF interface goes down and a
hi-jacked SKB exists, the original skb->destructor is restored.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
caif: Add support for flow-control on device's tx-queue
Flow control is implemented by inspecting the qdisc queue length
in order to detect potential overflow on the TX queue. When a threshold
is reached flow-off is sent upwards in the CAIF stack. At the same time
the skb->destructor is hi-jacked by orphaning the SKB and the original
destructor is replaced with a "flow-on" callback. When the "hi-jacked"
SKB is consumed the queue should be empty, and the "flow-on" callback
is called and xon is sent upwards in the CAIF stack.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
caif: Add support for CAIF over CDC NCM USB interface
NCM 1.0 does not support anything but Ethernet framing, hence
CAIF payload will be put into Ethernet frames.
Discovery is based on fixed USB vendor 0x04cc (ST-Ericsson),
product-id 0x230f (NCM). In this variant only CAIF payload is sent over
the NCM interface.
The CAIF stack (cfusbl.c) will when USB interface register first check if
we got a CDC NCM USB interface with the right VID, PID.
It will then read the device's Ethernet address and create a 'template'
Ethernet TX header, using a broadcast address as the destination address,
and EthType 0x88b5 (802.1 Local Experimental - vendor specific).
A protocol handler for 0x88b5 is setup for reception of CAIF frames from
the CDC NCM USB interface.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
if_ether.h: Add IEEE 802.1 Local Experimental Ethertype 1.
Add EthType 0x88b5.
This Ethertype value is available for public use for prototype and
vendor-specific protocol development,as defined in Amendment 802a
to IEEE Std 802.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Miller [Fri, 2 Dec 2011 16:52:44 +0000 (16:52 +0000)]
infiniband: ipoib: Sanitize neighbour handling in ipoib_main.c
Reduce the number of dst_get_neighbour_noref() calls within a single
call chain. Primarily by passing the neighbour pointer down to the
helper functions.
Handle dst_get_neighbour_noref() returning NULL in ipoib_start_xmit()
by incrementing the dropped counter and freeing the packet. We don't
want it to fall through into the ARP/RARP/multicast handling, since
that should only happen when skb_dst() is NULL.
Signed-off-by: David S. Miller <davem@davemloft.net> Acked-by: Roland Dreier <roland@purestorage.com>
David Miller [Fri, 2 Dec 2011 16:52:18 +0000 (16:52 +0000)]
cxgb3: Rework t3_l2t_get to take a dst_entry instead of a neighbour.
This way we consolidate the RCU locking down into the place where it
actually matters, and also we can make the code handle
dst_get_neighbour_noref() returning NULL properly.
Signed-off-by: David S. Miller <davem@davemloft.net>
Steven Rostedt [Sat, 5 Nov 2011 00:32:39 +0000 (20:32 -0400)]
ftrace: Fix hash record accounting bug
If the set_ftrace_filter is cleared by writing just whitespace to
it, then the filter hash refcounts will be decremented but not
updated. This causes two bugs:
1) No functions will be enabled for tracing when they all should be
2) If the users clears the set_ftrace_filter twice, it will crash ftrace:
Steven Rostedt [Fri, 4 Nov 2011 20:32:25 +0000 (16:32 -0400)]
perf: Fix parsing of __print_flags() in TP_printk()
A update is made to the sched:sched_switch event that adds some
logic to the first parameter of the __print_flags() that shows the
state of tasks. This change cause perf to fail parsing the flags.
A simple fix is needed to have the parser be able to process ops
within the argument.
Cc: stable@vger.kernel.org Reported-by: Andrew Vagin <avagin@openvz.org> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Gleb Natapov [Tue, 18 Oct 2011 17:55:51 +0000 (19:55 +0200)]
jump_label: jump_label_inc may return before the code is patched
If cpu A calls jump_label_inc() just after atomic_add_return() is
called by cpu B, atomic_inc_not_zero() will return value greater then
zero and jump_label_inc() will return to a caller before jump_label_update()
finishes its job on cpu B.
Link: http://lkml.kernel.org/r/20111018175551.GH17571@redhat.com Cc: stable@vger.kernel.org Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Jason Baron <jbaron@redhat.com> Signed-off-by: Gleb Natapov <gleb@redhat.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Steven Rostedt [Fri, 4 Nov 2011 14:45:23 +0000 (10:45 -0400)]
ftrace: Remove force undef config value left for testing
A forced undef of a config value was used for testing and was
accidently left in during the final commit. This causes x86 to
run slower than needed while running function tracing as well
as causes the function graph selftest to fail when DYNMAIC_FTRACE
is not set. This is because the code in MCOUNT expects the ftrace
code to be processed with the config value set that happened to
be forced not set.
Ilya Dryomov [Mon, 31 Oct 2011 09:07:42 +0000 (11:07 +0200)]
tracing: fix event_subsystem ref counting
Fix a bug introduced by e9dbfae5, which prevents event_subsystem from
ever being released.
Ref_count was added to keep track of subsystem users, not for counting
events. Subsystem is created with ref_count = 1, so there is no need to
increment it for every event, we have nr_events for that. Fix this by
touching ref_count only when we actually have a new user -
subsystem_open().
David S. Miller [Mon, 5 Dec 2011 18:21:42 +0000 (13:21 -0500)]
ipv4: Fix peer validation on cached lookup.
If ipv4_valdiate_peer() fails during a cached entry lookup,
we'll NULL derer since the loop iterator assumes rth is not
NULL.
Letting this be handled as a failure is just bogus, so just make it
not fail. If we have trouble getting a non-NULL neighbour for the
redirected gateway, just restore the original gateway and continue.
The very next use of this cached route will try again.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Seth Forshee [Wed, 16 Nov 2011 23:37:45 +0000 (17:37 -0600)]
toshiba_acpi: Fix machines that don't support HCI_SYSTEM_EVENT
The Satellite C670-10V generates notifications for hotkeys but does
not support HCI_SYSTEM_EVENT. As a result when a hotkey is pressed
it gets stuck in an infinite loop in toshiba_acpi_notify. To fix
this, detect whether or not HCI_SYSTEM_EVENT is supported up-front
and don't try to read system events if it isn't supported. In
addition, limit the number of retries when reading HCI_SYSTEM_EVENT
fails so that this loop cannot run unbounded.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Matthew Garrett <mjg@redhat.com>
intr_remapping: Fix section mismatch in ir_dev_scope_init()
Fix:
Section mismatch in reference from the function
ir_dev_scope_init() to the function
.init.text:dmar_dev_scope_init() The function
ir_dev_scope_init() references the function __init dmar_dev_scope_init().
intel-iommu: Fix section mismatch in dmar_parse_rmrr_atsr_dev()
dmar_parse_rmrr_atsr_dev() calls rmrr_parse_dev() and
atsr_parse_dev() which are both marked as __init.
Section mismatch in reference from the function
dmar_parse_rmrr_atsr_dev() to the function
.init.text:dmar_parse_dev_scope() The function
dmar_parse_rmrr_atsr_dev() references the function __init
dmar_parse_dev_scope().
Section mismatch in reference from the function
dmar_parse_rmrr_atsr_dev() to the function
.init.text:dmar_parse_dev_scope() The function
dmar_parse_rmrr_atsr_dev() references the function __init
dmar_parse_dev_scope().
x86, amd: Fix up numa_node information for AMD CPU family 15h model 0-0fh northbridge functions
I've received complaints that the numa_node attribute for family
15h model 00-0fh (e.g. Interlagos) northbridge functions shows
-1 instead of the proper node ID.
Correct this with attached quirks (similar to quirks for other
AMD CPU families used in multi-socket systems).
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com> Cc: Frank Arnold <frank.arnold@amd.com> Cc: Borislav Petkov <borislav.petkov@amd.com> Link: http://lkml.kernel.org/r/20111202072143.GA31916@alberich.amd.com Signed-off-by: Ingo Molnar <mingo@elte.hu>
Borislav Petkov [Mon, 21 Nov 2011 11:10:19 +0000 (12:10 +0100)]
x86, AMD: Correct align_va_addr documentation
Commit dfb09f9b7ab0 ("x86, amd: Avoid cache aliasing penalties
on AMD family 15h") introduced a kernel command line parameter
called 'align_va_addr' which still refers to arguments used in
an earlier version of the patch and which got changed without
updating the documentation. Correct that omission.
The problem is that in copy_page_range() we turn lazy mode on,
and then in swap_entry_free() we call swap_count_continued()
which ends up in:
map = kmap_atomic(page, KM_USER0) + offset;
and then later we touch *map.
Since we are running in batched mode (lazy) we don't actually
set up the PTE mappings and the kmap_atomic is not done
synchronously and ends up trying to dereference a page that has
not been set.
Looking at kmap_atomic_prot_pfn(), it uses
'arch_flush_lazy_mmu_mode' and doing the same in
kmap_atomic_prot() and __kunmap_atomic() makes the problem go
away.
Interestingly, commit b8bcfe997e4615 ("x86/paravirt: remove lazy
mode in interrupts") removed part of this to fix an interrupt
issue - but it went to far and did not consider this scenario.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Peter Chubb [Mon, 5 Dec 2011 13:53:53 +0000 (16:53 +0300)]
x86: Fix "Acer Aspire 1" reboot hang
Looks like on some Acer Aspire 1s with older bioses, reboot via bios
fails. It works on my machine, (with BIOS version 0.3310) but
not on some others (BIOS version 0.3309).
There's a log of problems at:
https://bbs.archlinux.org/viewtopic.php?id=124136
This patch adds a different callback to the reboot quirk table,
to allow rebooting via keybaord controller.
Reported-by: Uroš Vampl <mobile.leecher@gmail.com> Tested-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Peter Chubb <peter.chubb@nicta.com.au> Cc: Don Zickus <dzickus@redhat.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: stable@kernel.org Link: http://lkml.kernel.org/r/1323093233-9481-1-git-send-email-anarsoul@gmail.com Signed-off-by: Ingo Molnar <mingo@elte.hu>
x86/mtrr: Resolve inconsistency with Intel processor manual
Following is from Notes of section 11.5.3 of Intel processor
manual available at:
http://www.intel.com/Assets/PDF/manual/325384.pdf
For the Pentium 4 and Intel Xeon processors, after the sequence of
steps given above has been executed, the cache lines containing the
code between the end of the WBINVD instruction and before the
MTRRS have actually been disabled may be retained in the cache
hierarchy. Here, to remove code from the cache completely, a
second WBINVD instruction must be executed after the MTRRs have
been disabled.
This patch provides resolution for that.
Ideally, I will like to make changes only for Pentium 4 and Xeon
processors. But, I am not finding easier way to do it.
And, extra wbinvd() instruction does not hurt much for other
processors.
Signed-off-by: Ajaykumar Hotchandani <ajaykumar.hotchandani@oracle.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi> Link: http://lkml.kernel.org/r/4EBD1CC5.3030008@oracle.com Signed-off-by: Ingo Molnar <mingo@elte.hu>
x86/mpparse: Account for bus types other than ISA and PCI
In commit f8924e770e04 ("x86: unify mp_bus_info"), the 32-bit
and 64-bit versions of MP_bus_info were rearranged to match each
other better. Unfortunately it introduced a regression: prior
to that change we used to always set the mp_bus_not_pci bit,
then clear it if we found a PCI bus. After it, we set
mp_bus_not_pci for ISA buses, clear it for PCI buses, and leave
it alone otherwise.
In the cases of ISA and PCI, there's not much difference. But
ISA is not the only non-PCI bus, so it's better to always set
mp_bus_not_pci and clear it only for PCI.
Without this change, Dan's Dell PowerEdge 4200 panics on boot
with a log indicating interrupt routing trouble unless the
"noapic" option is supplied. With this change, the machine
boots reliably without "noapic".
Jacob Pan [Wed, 16 Nov 2011 16:07:22 +0000 (16:07 +0000)]
x86,mrst: Power control commands update
On the Intel MID devices SCU commands are issued to manage power
off and the like. We need to issue different ones for
non-Lincroft based devices.
Signed-off-by: Alek Du <alek.du@intel.com> Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Jack Steiner [Tue, 29 Nov 2011 21:00:58 +0000 (15:00 -0600)]
x86, UV: Fix UV2 hub part number
There was a mixup when the SGI UV2 hub chip was sent to be
fabricated, and it ended up with the wrong part number in the
HRP_NODE_ID mmr. Future versions of the chip will (may) have the
correct part number. Change the UV infrastructure to recognize
both part numbers as valid IDs of a UV2 hub chip.
Mitsuo Hayasaka [Tue, 29 Nov 2011 06:08:21 +0000 (15:08 +0900)]
x86: Add user_mode_vm check in stack_overflow_check
The kernel stack overflow is checked in stack_overflow_check(),
which may wrongly detect the overflow if the stack pointer in
user space points to the kernel stack intentionally or
accidentally. So, the actual overflow is never detected after
this misdetection because WARN_ONCE() is used on the detection
of it.
This patch adds user-mode-vm checking before it to avoid this
problem and bails out early if the user stack is used.
Peter Zijlstra [Mon, 28 Nov 2011 20:12:40 +0000 (21:12 +0100)]
slab, lockdep: Fix silly bug
Commit 30765b92 ("slab, lockdep: Annotate the locks before using
them") moves the init_lock_keys() call from after g_cpucache_up =
FULL, to before it. And overlooks the fact that init_node_lock_keys()
tests for it and ignores everything !FULL.
Introduce a LATE stage and change the lockdep test to be <LATE.
Acked-by: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: stable@kernel.org Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Peter Zijlstra [Sat, 26 Nov 2011 01:47:31 +0000 (02:47 +0100)]
perf: Fix loss of notification with multi-event
When you do:
$ perf record -e cycles,cycles,cycles noploop 10
You expect about 10,000 samples for each event, i.e., 10s at
1000samples/sec. However, this is not what's happening. You
get much fewer samples, maybe 3700 samples/event:
$ perf report -D | tail -15
Aggregated stats:
TOTAL events: 10998
MMAP events: 66
COMM events: 2
SAMPLE events: 10930
cycles stats:
TOTAL events: 3644
SAMPLE events: 3644
cycles stats:
TOTAL events: 3642
SAMPLE events: 3642
cycles stats:
TOTAL events: 3644
SAMPLE events: 3644
On a Intel Nehalem or even AMD64, there are 4 counters capable
of measuring cycles, so there is plenty of space to measure those
events without multiplexing (even with the NMI watchdog active).
And even with multiplexing, we'd expect roughly the same number
of samples per event.
The root of the problem was that when the event that caused the buffer
to become full was not the first event passed on the cmdline, the user
notification would get lost. The notification was sent to the file
descriptor of the overflowed event but the perf tool was not polling
on it. The perf tool aggregates all samples into a single buffer,
i.e., the buffer of the first event. Consequently, it assumes
notifications for any event will come via that descriptor.
The seemingly straight forward solution of moving the waitq into the
ringbuffer object doesn't work because of life-time issues. One could
perf_event_set_output() on a fd that you're also blocking on and cause
the old rb object to be freed while its waitq would still be
referenced by the blocked thread -> FAIL.
Therefore link all events to the ringbuffer and broadcast the wakeup
from the ringbuffer object to all possible events that could be waited
upon. This is rather ugly, and we're open to better solutions but it
works for now.
projects / mirror_ubuntu-bionic-kernel.git / log