Jarkko Sakkinen [Fri, 12 Dec 2014 19:46:40 +0000 (11:46 -0800)]
tpm: TPM 2.0 FIFO Interface
Detect TPM 2.0 by sending idempotent TPM 2.x command. Ordinals for
TPM 2.0 are higher than TPM 1.x commands so this should be fail-safe.
Using STS3 is unreliable because some chips just report 0xff and not
what the spec says.
Before TPM family is detected, timeouts are set to the maximum values
for both TPM 1.x and TPM 2.x. In addition to this, suspend/resume
functionality is implemented for TPM 2.x.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Will Arthur <will.c.arthur@intel.com> Reviewed-by: Jasob Gunthorpe <jason.gunthorpe@obsidianresearch.com> Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com> Reviewed-by: Peter Huewe <peterhuewe@gmx.de> Tested-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Jarkko Sakkinen [Fri, 12 Dec 2014 19:46:39 +0000 (11:46 -0800)]
tpm: TPM 2.0 CRB Interface
tpm_crb is a driver for TPM 2.0 Command Response Buffer (CRB) Interface
as defined in PC Client Platform TPM Profile (PTP) Specification.
Only polling and single locality is supported as these are the limitations
of the available hardware, Platform Trust Techonlogy (PTT) in Haswell
CPUs.
The driver always applies CRB with ACPI start because PTT reports using
only ACPI start as start method but as a result of my testing it requires
also CRB start.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Reviewed-by: Jasob Gunthorpe <jason.gunthorpe@obsidianresearch.com> Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com> Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
The existing functions that are exported for the use for existing
subsystems have been changed to check the flags field in struct
tpm_chip and use appropriate TPM 2.0 counterpart if
TPM_CHIP_FLAG_TPM2 is est.
The code for tpm2_calc_ordinal_duration() and tpm2_startup() were
originally written by Will Arthur.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Will Arthur <will.c.arthur@intel.com> Reviewed-by: Jasob Gunthorpe <jason.gunthorpe@obsidianresearch.com> Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com> Reviewed-by: Peter Huewe <peterhuewe@gmx.de> Tested-by: Peter Huewe <peterhuewe@gmx.de>
[phuewe: Fixed copy paste error * 2] Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Jarkko Sakkinen [Fri, 12 Dec 2014 19:46:37 +0000 (11:46 -0800)]
tpm: device class for tpm
Added own device class for TPM. Uses MISC_MAJOR:TPM_MINOR for the
first character device in order to retain backwards compatibility.
Added tpm_dev_release() back attached to the character device.
I've been running this code now for a while on my laptop (Lenovo
T430S) TrouSerS works perfectly without modifications. I don't
believe it breaks anything significantly.
The sysfs attributes that have been placed under the wrong place
and are against sysfs-rules.txt should be probably left to
stagnate under platform device directory and start defining
new sysfs attributes to the char device directory.
Guidelines for future TPM sysfs attributes should be probably
along the lines of
- Single flat set of mandatory sysfs attributes. For example,
current PPI interface is way way too rich when you only want
to use it to clear and activate the TPM.
- Define sysfs attribute if and only if there's no way to get
the value from ring-3. No attributes for TPM properties. It's
just unnecessary maintenance hurdle that we don't want.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Reviewed-by: Jasob Gunthorpe <jason.gunthorpe@obsidianresearch.com> Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com> Tested-by: Scot Doyle <lkml14@scotdoyle.com> Tested-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Jarkko Sakkinen [Fri, 12 Dec 2014 19:46:35 +0000 (11:46 -0800)]
tpm: fix raciness of PPI interface lookup
Traversal of the ACPI device tree was not done right. PPI interface
should be looked up only from the ACPI device that is the platform
device for the TPM. This could cause problems with systems with
two TPM chips such as 4th gen Intel systems.
In addition, added the missing license and copyright platter to
the tpm_ppi.c.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Reviewed-by: Jasob Gunthorpe <jason.gunthorpe@obsidianresearch.com> Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com> Tested-by: Scot Doyle <lkml14@scotdoyle.com> Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Jarkko Sakkinen [Fri, 12 Dec 2014 19:46:34 +0000 (11:46 -0800)]
tpm: two-phase chip management functions
tpm_register_hardware() and tpm_remove_hardware() are called often
before initializing the device. The problem is that the device might
not be fully initialized when it comes visible to the user space.
This patch resolves the issue by diving initialization into two
parts:
- tpmm_chip_alloc() creates struct tpm_chip.
- tpm_chip_register() sets up the character device and sysfs
attributes.
The framework takes care of freeing struct tpm_chip by using the devres
API. The broken release callback has been wiped. ACPI drivers do not
ever get this callback.
Regards to Jason Gunthorpe for carefully reviewing this part of the
code.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Reviewed-by: Jasob Gunthorpe <jason.gunthorpe@obsidianresearch.com> Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com> Tested-by: Scot Doyle <lkml14@scotdoyle.com> Tested-by: Peter Huewe <peterhuewe@gmx.de>
[phuewe: update to upstream changes] Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Jarkko Sakkinen [Fri, 12 Dec 2014 19:46:33 +0000 (11:46 -0800)]
tpm: merge duplicate transmit_cmd() functions
Merged transmit_cmd() functions in tpm-interface.c and tpm-sysfs.c.
Added "tpm_" prefix for consistency sake. Changed cmd parameter as
opaque. This enables to use separate command structures for TPM1
and TPM2 commands in future. Loose coupling works fine here.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Reviewed-by: Jasob Gunthorpe <jason.gunthorpe@obsidianresearch.com> Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com> Reviewed-by: Peter Huewe <peterhuewe@gmx.de> Tested-by: Scot Doyle <lkml14@scotdoyle.com> Tested-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Ashley Lai [Fri, 5 Dec 2014 03:01:51 +0000 (21:01 -0600)]
tpm_ibmvtpm: Update email address in maintainers list and ibmvtpm driver
Added myself as a maintainer for the IBM vtpm driver and removed myself
from the tpm maintainer list. Also, updated the tpm_ibmvtpm driver with
my current email address.
Signed-off-by: Ashley Lai <ashleydlai@gmail.com> Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Improve the irq management by using a new function wait_for_stat.
Instead of using a completion struct, we rely on the waitqueue read_queue
and int_queue from chip->vendor field.
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Add tpm_stm_st33_i2c dts structure keeping backward compatibility
with static platform_data support as well.
In the mean time to easy this update and to make it much simpler, we:
- Moved all gpio_request to devm_gpio_request_one primitive
- Moved request_irq to devm_request_irq
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
tpm/tpm_i2c_stm_st33: Remove reference to io_serirq
The serirq gpio pin is used only as interrupt. After driver initialization,
the serirq signal is always used through interrupt and never with gpio
kernel API.
The irq can then be initialized during the platform_data definition within the client->irq pin.
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
tpm/tpm_i2c_stm_st33: Add new tpm_stm_dev structure and remove tpm_i2c_buffer[0], [1] buffer.
In order to clean big buffers in st33zp24_platform_data structure,
replace with tpm_stm_dev for driver internal usage.
As only one buffer is really necessary replace with buf field.
In the mean time move tpm_i2c_stm_st33.h to include/linux/platform_data.
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
tpm/tpm_i2c_stm_st33: Change License header to have up to date address information
The Free Software Foundation may have mail address change.
In order to be sure to have up to date mail address give an url to
the license which includes accurate informations.
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
tpm/tpm_i2c_stm_st33: Update Kconfig in order to be inline to other similar product
STMicroelectronics i2c tpm is the only one to have a different tristate
label.
Rename it "TPM Interface Specification 1.2 Interface (I2C - STMicroelectronics)"
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
[phuewe: corrected module name in the helptext] Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
tpm/tpm_i2c_stm_st33: Fix potential bug in tpm_stm_i2c_send
When sending data in tpm_stm_i2c_send, each loop iteration send buf.
Send buf + i instead as the goal of this for loop is to send a number
of byte from buf that fit in burstcnt. Once those byte are sent, we are
supposed to send the next ones.
The driver was working because the burstcount value returns always the maximum size for a TPM
command or response. (0x800 for a command and 0x400 for a response).
Cc: stable@vger.kernel.org Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
tpm: Fix NULL return in tpm_ibmvtpm_get_desired_dma
There was an oops in tpm_ibmvtpm_get_desired_dma, which caused
kernel panic during boot when vTPM is enabled in Power partition
configured in AMS mode.
vio_bus_probe calls vio_cmo_bus_probe which calls
tpm_ibmvtpm_get_desired_dma to get the size needed for DMA allocation.
The problem is, vio_cmo_bus_probe is called before calling probe, which
for vtpm is tpm_ibmvtpm_probe and it's this function that initializes
and sets up vtpm's CRQ and gets required data values. Therefore,
since this has not yet been done, NULL is returned in attempt to get
the size for DMA allocation.
We added a NULL check. In addition, a default buffer size will
be set when NULL is returned.
Cc: <stable@vger.kernel.org> Signed-off-by: Hon Ching (Vicky) Lo <honclo@linux.vnet.ibm.com> Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Some machines, such as the Acer C720 and Toshiba CB35, have TPMs that do
not send IRQs while also having an ACPI TPM entry indicating that they
will be sent. These machines freeze on resume while the tpm_tis module
waits for an IRQ, eventually timing out.
When in interrupt mode, the tpm_tis module should receive an IRQ during
module init. Fall back to polling mode if none is received when expected.
Cc: <stable@vger.kernel.org> Signed-off-by: Scot Doyle <lkml14@scotdoyle.com> Tested-by: Michael Mullin <masmullin@gmail.com> Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[phuewe: minor checkpatch fixed] Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
David Howells [Fri, 29 Aug 2014 09:33:02 +0000 (10:33 +0100)]
TPM: Add new TPMs to the tail of the list to prevent inadvertent change of dev
Add newly registered TPMs to the tail of the list, not the beginning, so that
things that are specifying TPM_ANY_NUM don't find that the device they're
using has inadvertently changed. Adding a second device would break IMA, for
instance.
Cc: stable@vger.kernel.org Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
1) Don't use uninitialized data in IPVS, from Dan Carpenter.
2) conntrack race fixes from Pablo Neira Ayuso.
3) Fix TX hangs with i40e, from Jesse Brandeburg.
4) Fix budget return from poll calls in dnet and alx, from Eric
Dumazet.
5) Fix bugus "if (unlikely(x) < 0)" test in AF_PACKET, from Christoph
Jaeger.
6) Fix bug introduced by conversion to list_head in TIPC retransmit
code, from Jon Paul Maloy.
7) Don't use GFP_NOIO under spinlock in USB kaweth driver, from Alexey
Khoroshilov.
8) Fix bridge build with INET disabled, from Arnd Bergmann.
9) Fix netlink array overrun for PROBE attributes in openvswitch, from
Thomas Graf.
10) Don't hold spinlock across synchronize_irq() in tg3 driver, from
Prashant Sreedharan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
tg3: Release tp->lock before invoking synchronize_irq()
tg3: tg3_reset_task() needs to use rtnl_lock to synchronize
tg3: tg3_timer() should grab tp->lock before checking for tp->irq_sync
team: avoid possible underflow of count_pending value for notify_peers and mcast_rejoin
openvswitch: packet messages need their own probe attribtue
i40e: adds FCoE configure option
cxgb4vf: Fix queue allocation for 40G adapter
netdevice: Add missing parentheses in macro
bridge: only provide proxy ARP when CONFIG_INET is enabled
neighbour: fix base_reachable_time(_ms) not effective immediatly when changed
net: fec: fix MDIO bus assignement for dual fec SoC's
xen-netfront: use different locks for Rx and Tx stats
drivers: net: cpsw: fix multicast flush in dual emac mode
cxgb4vf: Initialize mdio_addr before using it
net: Corrected the comment describing the ndo operations to reflect the actual prototype for couple of operations
usb/kaweth: use GFP_ATOMIC under spin_lock in usb_start_wait_urb()
MAINTAINERS: add me as ibmveth maintainer
tipc: fix bug in broadcast retransmit code
update ip-sysctl.txt documentation (v2)
net/at91_ether: prepare and unprepare clock
...
tg3: Release tp->lock before invoking synchronize_irq()
synchronize_irq() can sleep waiting, for pending IRQ handlers so driver
should release the tp->lock spin lock before invoking synchronize_irq()
Reported-by: Peter Hurley <peter@hurleysoftware.com> Tested-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Prashant Sreedharan <prashant@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tg3: tg3_reset_task() needs to use rtnl_lock to synchronize
Currently tg3_reset_task() uses only tp->lock for synchronizing with code
paths like tg3_open() etc. But since tp->lock is released before doing
synchronize_irq(), rtnl_lock should be taken in tg3_reset_task() to
synchronize it with other code paths.
Reported-by: Peter Hurley <peter@hurleysoftware.com> Tested-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Prashant Sreedharan <prashant@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tg3: tg3_timer() should grab tp->lock before checking for tp->irq_sync
This is to avoid the race between tg3_timer() and the execution paths
which does not invoke tg3_timer_stop() and releases tp->lock before
calling synchronize_irq()
Reported-by: Peter Hurley <peter@hurleysoftware.com> Tested-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Prashant Sreedharan <prashant@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 14 Jan 2015 21:54:30 +0000 (10:54 +1300)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Two bugfixes for arm64. I will have another pull request next week,
but otherwise things are calm"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
arm64: KVM: Fix HCR setting for 32bit guests
arm64: KVM: Fix TLB invalidation by IPA/VMID
Jiri Pirko [Wed, 14 Jan 2015 17:15:30 +0000 (18:15 +0100)]
team: avoid possible underflow of count_pending value for notify_peers and mcast_rejoin
This patch is fixing a race condition that may cause setting
count_pending to -1, which results in unwanted big bulk of arp messages
(in case of "notify peers").
Consider following scenario:
count_pending == 2
CPU0 CPU1
team_notify_peers_work
atomic_dec_and_test (dec count_pending to 1)
schedule_delayed_work
team_notify_peers
atomic_add (adding 1 to count_pending)
team_notify_peers_work
atomic_dec_and_test (dec count_pending to 1)
schedule_delayed_work
team_notify_peers_work
atomic_dec_and_test (dec count_pending to 0)
schedule_delayed_work
team_notify_peers_work
atomic_dec_and_test (dec count_pending to -1)
Fix this race by using atomic_dec_if_positive - that will prevent
count_pending running under 0.
Fixes: fc423ff00df3a1955441 ("team: add peer notification") Fixes: 492b200efdd20b8fcfd ("team: add support for sending multicast rejoins") Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 14 Jan 2015 21:50:29 +0000 (10:50 +1300)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Two small performance tweaks, the plumbing for the execveat system
call and a couple of bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/uprobes: fix user space PER events
s390/bpf: Fix JMP_JGE_X (A > X) and JMP_JGT_X (A >= X)
s390/bpf: Fix ALU_NEG (A = -A)
s390/mm: avoid using pmd_to_page for !USE_SPLIT_PMD_PTLOCKS
s390/timex: fix get_tod_clock_ext() inline assembly
s390: wire up execveat syscall
s390/kernel: use stnsm 255 instead of stosm 0
s390/vtime: Get rid of redundant WARN_ON
s390/zcrypt: kernel oops at insmod of the z90crypt device driver
Thomas Graf [Wed, 14 Jan 2015 13:56:19 +0000 (13:56 +0000)]
openvswitch: packet messages need their own probe attribtue
User space is currently sending a OVS_FLOW_ATTR_PROBE for both flow
and packet messages. This leads to an out-of-bounds access in
ovs_packet_cmd_execute() because OVS_FLOW_ATTR_PROBE >
OVS_PACKET_ATTR_MAX.
Introduce a new OVS_PACKET_ATTR_PROBE with the same numeric value
as OVS_FLOW_ATTR_PROBE to grow the range of accepted packet attributes
while maintaining to be binary compatible with existing OVS binaries.
Fixes: 05da589 ("openvswitch: Add support for OVS_FLOW_ATTR_PROBE.") Reported-by: Sander Eikelenboom <linux@eikelenboom.it> Tracked-down-by: Florian Westphal <fw@strlen.de> Signed-off-by: Thomas Graf <tgraf@suug.ch> Reviewed-by: Jesse Gross <jesse@nicira.com> Acked-by: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vasu Dev [Wed, 14 Jan 2015 13:14:07 +0000 (05:14 -0800)]
i40e: adds FCoE configure option
Adds FCoE config option I40E_FCOE, so that FCoE can be enabled
as needed but otherwise have it disabled by default.
This also eliminate multiple FCoE config checks, instead now just
one config check for CONFIG_I40E_FCOE.
The I40E FCoE was added with 3.17 kernel and therefore this patch
shall be applied to stable 3.17 kernel also.
CC: <stable@vger.kernel.org> Signed-off-by: Vasu Dev <vasu.dev@intel.com> Tested-by: Jim Young <jamesx.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 14 Jan 2015 21:38:07 +0000 (10:38 +1300)]
Merge tag 'locks-v3.19-1' of git://git.samba.org/jlayton/linux
Pull file locking fix from Jeff Layton:
"Just a simple bugfix for a regression that I introduced into v3.18
with the internal lease API overhaul -- mea culpa. Kudos to Linda and
Neil for tracking this down and fixing it"
* tag 'locks-v3.19-1' of git://git.samba.org/jlayton/linux:
locks: fix NULL-deref in generic_delete_lease
Linus Torvalds [Wed, 14 Jan 2015 21:27:56 +0000 (10:27 +1300)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block layer fixes from Jens Axboe:
"The major part is an update to the NVMe driver, fixing various issues
around surprise removal and hung controllers. Most of that is from
Keith, and parts are simple blk-mq fixes or exports/additions of minor
functions to aid this effort, and parts are changes directly to the
NVMe driver.
Apart from the above, this contains:
- Small blk-mq change from me, killing an unused member of the
hardware queue structure.
- Small fix from Ming Lei, fixing up a few drivers that didn't
properly check for ERR_PTR() returns from blk_mq_init_queue()"
* 'for-linus' of git://git.kernel.dk/linux-block:
NVMe: Fix locking on abort handling
NVMe: Start and stop h/w queues on reset
NVMe: Command abort handling fixes
NVMe: Admin queue removal handling
NVMe: Reference count admin queue usage
NVMe: Start all requests
blk-mq: End unstarted requests on a dying queue
blk-mq: Allow requests to never expire
blk-mq: Add helper to abort requeued requests
blk-mq: Let drivers cancel requeue_work
blk-mq: Export if requests were started
blk-mq: Wake tasks entering queue on dying
blk-mq: get rid of ->cmd_size in the hardware queue
block: fix checking return value of blk_mq_init_queue
block: wake up waiters when a queue is marked dying
NVMe: Fix double free irq
blk-mq: Export freeze/unfreeze functions
blk-mq: Exit queue on alloc failure
Arnd Bergmann [Tue, 13 Jan 2015 14:10:27 +0000 (15:10 +0100)]
bridge: only provide proxy ARP when CONFIG_INET is enabled
When IPV4 support is disabled, we cannot call arp_send from
the bridge code, which would result in a kernel link error:
net/built-in.o: In function `br_handle_frame_finish':
:(.text+0x59914): undefined reference to `arp_send'
:(.text+0x59a50): undefined reference to `arp_tbl'
This makes the newly added proxy ARP support in the bridge
code depend on the CONFIG_INET symbol and lets the compiler
optimize the code out to avoid the link error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 958501163ddd ("bridge: Add support for IEEE 802.11 Proxy ARP") Cc: Kyeyoon Park <kyeyoonp@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Rasmus Villemoes [Wed, 14 Jan 2015 16:10:12 +0000 (16:10 +0000)]
MPILIB: Fix comparison of negative MPIs
If u and v both represent negative integers and their limb counts
happen to differ, mpi_cmp will always return a positive value - this
is obviously bogus. u is smaller than v if and only if it is larger in
absolute value.
Rasmus Villemoes [Wed, 14 Jan 2015 15:15:57 +0000 (15:15 +0000)]
MPILIB: Deobfuscate mpi_cmp
The condition preceding 'return 1;' makes my head hurt. At this point,
we know that u and v have the same sign; if they are negative, they
compare opposite to how their absolute values compare (which
mpihelp_cmp found for us), otherwise cmp itself is the
answer. Negating cmp is ok since mpihelp_cmp returns {-1,0,1};
-INT_MIN==INT_MIN won't bite us.
neighbour: fix base_reachable_time(_ms) not effective immediatly when changed
When setting base_reachable_time or base_reachable_time_ms on a
specific interface through sysctl or netlink, the reachable_time
value is not updated.
This means that neighbour entries will continue to be updated using the
old value until it is recomputed in neigh_period_work (which
recomputes the value every 300*HZ).
On systems with HZ equal to 1000 for instance, it means 5mins before
the change is effective.
This patch changes this behavior by recomputing reachable_time after
each set on base_reachable_time or base_reachable_time_ms.
The new value will become effective the next time the neighbour's timer
is triggered.
Changes are made in two places: the netlink code for set and the sysctl
handling code. For sysctl, I use a proc_handler. The ipv6 network
code does provide its own handler but it already refreshes
reachable_time correctly so it's not an issue.
Any other user of neighbour which provide its own handlers must
refresh reachable_time.
Signed-off-by: Jean-Francois Remy <jeff@melix.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Agner [Tue, 13 Jan 2015 23:20:21 +0000 (00:20 +0100)]
net: fec: fix MDIO bus assignement for dual fec SoC's
On i.MX28, the MDIO bus is shared between the two FEC instances.
The driver makes sure that the second FEC uses the MDIO bus of the
first FEC. This is done conditionally if FEC_QUIRK_ENET_MAC is set.
However, in newer designs, such as Vybrid or i.MX6SX, each FEC MAC
has its own MDIO bus. Simply removing the quirk FEC_QUIRK_ENET_MAC
is not an option since other logic, triggered by this quirk, is
still needed.
Furthermore, there are board designs which use the same MDIO bus
for both PHY's even though the second bus would be available on the
SoC side. Such layout are popular since it saves pins on SoC side.
Due to the above quirk, those boards currently do work fine. The
boards in the mainline tree with such a layout are:
- Freescale Vybrid Tower with TWR-SER2 (vf610-twr.dts)
- Freescale i.MX6 SoloX SDB Board (imx6sx-sdb.dts)
This patch adds a new quirk FEC_QUIRK_SINGLE_MDIO for i.MX28, which
makes sure that the MDIO bus of the first FEC is used in any case.
However, the boards above do have a SoC with a MDIO bus for each FEC
instance. But the PHY's are not connected in a 1:1 configuration. A
proper device tree description is needed to allow the driver to
figure out where to find its PHY. This patch fixes that shortcoming
by adding a MDIO bus child node to the first FEC instance, along
with the two PHY's on that bus, and making use of the phy-handle
property to add a reference to the PHY's.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 13 Jan 2015 22:54:12 +0000 (11:54 +1300)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/borntraeger/linux
Pull WRITE_ONCE argument order change from Christian Borntraeger:
"As discussed on LKML[1] it was agreed that WRITE_ONCE(x, val) is
better than ASSIGN_ONCE(val, x)
Lets change that for 3.19 as 3.19 has no user yet, but the first users
will hit linux-next soon"
David Vrabel [Tue, 13 Jan 2015 16:42:42 +0000 (16:42 +0000)]
xen-netfront: use different locks for Rx and Tx stats
In netfront the Rx and Tx path are independent and use different
locks. The Tx lock is held with hard irqs disabled, but Rx lock is
held with only BH disabled. Since both sides use the same stats lock,
a deadlock may occur.
[ INFO: possible irq lock inversion dependency detected ]
3.16.2 #16 Not tainted
---------------------------------------------------------
swapper/0/0 just changed the state of lock:
(&(&queue->tx_lock)->rlock){-.....}, at: [<c03adec8>]
xennet_tx_interrupt+0x14/0x34
but this lock took another, HARDIRQ-unsafe lock in the past:
(&stat->syncp.seq#2){+.-...}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
Using separate locks for the Rx and Tx stats fixes this deadlock.
Reported-by: Dmitry Piotrovsky <piotrovskydmitry@gmail.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mugunthan V N [Tue, 13 Jan 2015 12:05:49 +0000 (17:35 +0530)]
drivers: net: cpsw: fix multicast flush in dual emac mode
Since ALE table is a common resource for both the interfaces in Dual EMAC
mode and while bringing up the second interface in cpsw_ndo_set_rx_mode()
all the multicast entries added by the first interface is flushed out and
only second interface multicast addresses are added. Fixing this by
flushing multicast addresses based on dual EMAC port vlans which will not
affect the other emac port multicast addresses.
Fixes: d9ba8f9 (driver: net: ethernet: cpsw: dual emac interface implementation) Cc: <stable@vger.kernel.org> # v3.9+ Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Guinot [Tue, 2 Dec 2014 15:32:10 +0000 (07:32 -0800)]
leds: netxbig: fix oops at probe time
This patch fixes a NULL pointer dereference on led_dat->mode_val. Due to
this bug, a kernel oops can be observed at probe time on the LaCie 2Big
and 5Big v2 boards:
Unable to handle kernel NULL pointer dereference at virtual address 00000008
[...]
[<c03f244c>] (netxbig_led_probe) from [<c02c8c6c>] (platform_drv_probe+0x4c/0x9c)
[<c02c8c6c>] (platform_drv_probe) from [<c02c72d0>] (driver_probe_device+0x98/0x25c)
[<c02c72d0>] (driver_probe_device) from [<c02c7520>] (__driver_attach+0x8c/0x90)
[<c02c7520>] (__driver_attach) from [<c02c5c24>] (bus_for_each_dev+0x68/0x94)
[<c02c5c24>] (bus_for_each_dev) from [<c02c6408>] (bus_add_driver+0x124/0x1dc)
[<c02c6408>] (bus_add_driver) from [<c02c7ac0>] (driver_register+0x78/0xf8)
[<c02c7ac0>] (driver_register) from [<c000888c>] (do_one_initcall+0x80/0x1cc)
[<c000888c>] (do_one_initcall) from [<c0733618>] (kernel_init_freeable+0xe4/0x1b4)
[<c0733618>] (kernel_init_freeable) from [<c058db9c>] (kernel_init+0xc/0xec)
[<c058db9c>] (kernel_init) from [<c0009850>] (ret_from_fork+0x14/0x24)
[...]
kernel: Change ASSIGN_ONCE(val, x) to WRITE_ONCE(x, val)
Feedback has shown that WRITE_ONCE(x, val) is easier to use than
ASSIGN_ONCE(val,x).
There are no in-tree users yet, so lets change it for 3.19.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Acked-by: Peter Zijlstra <peterz@infradead.org> Acked-by: Davidlohr Bueso <dave@stgolabs.net> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Linus Torvalds [Tue, 13 Jan 2015 19:09:14 +0000 (08:09 +1300)]
Merge tag 'linux-kselftest-3.19-rc-5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
"This update contains three patches to fix one compile error, and two
run-time bugs. One of them fixes infinite loop on ARM"
* tag 'linux-kselftest-3.19-rc-5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/vm: fix link error for transhuge-stress test
tools: testing: selftests: mq_perf_tests: Fix infinite loop on ARM
selftests/exec: allow shell return code of 126
Linus Torvalds [Tue, 13 Jan 2015 19:07:42 +0000 (08:07 +1300)]
Merge tag 'stable/for-linus-3.19-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
"Several critical linear p2m fixes that prevented some hosts from
booting"
* tag 'stable/for-linus-3.19-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: properly retrieve NMI reason
xen: check for zero sized area when invalidating memory
xen: use correct type for physical addresses
xen: correct race in alloc_p2m_pmd()
xen: correct error for building p2m list on 32 bits
x86/xen: avoid freeing static 'name' when kasprintf() fails
x86/xen: add extra memory for remapped frames during setup
x86/xen: don't count how many PFNs are identity mapped
x86/xen: Free bootmem in free_p2m_page() during early boot
x86/xen: Remove unnecessary BUG_ON(preemptible()) in xen_setup_timer()
Linus Torvalds [Tue, 13 Jan 2015 18:53:51 +0000 (07:53 +1300)]
Merge branch 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management fixes from Zhang Rui:
"Specifics:
- Fix a problem that Intel SoC DTS thermal driver does not work when
CONFIG_THERMAL_INT340X is not set.
- Fix a NULL pointer dereference when processor_thermal_device driver
is loaded on a platform without ACPI support"
* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
int340x_thermal/processor_thermal_device: return failure when
ACPI/int340x_thermal: enumerate INT3401 for Intel SoC DTS thermal driver
ACPI/int340x_thermal: enumerate INT340X devices even if they're not in _ART/_TRT
moves the call to fl->fl_lmops->lm_change() to a place in the
code where fl might be a non-lease lock.
When that happens, fl_lmops is NULL and an Oops ensures.
So add an extra test to restore correct functioning.
Reported-by: Linda Walsh <suse@tlinx.org> Link: https://bugzilla.suse.com/show_bug.cgi?id=912569 Cc: stable@vger.kernel.org (v3.18) Fixes: 0efaa7e82f02fe69c05ad28e905f31fc86e6f08e Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Jan Beulich [Tue, 13 Jan 2015 07:40:05 +0000 (07:40 +0000)]
x86/xen: properly retrieve NMI reason
Using the native code here can't work properly, as the hypervisor would
normally have cleared the two reason bits by the time Dom0 gets to see
the NMI (if passed to it at all). There's a shared info field for this,
and there's an existing hook to use - just fit the two together. This
is particularly relevant so that NMIs intended to be handled by APEI /
GHES actually make it to the respective handler.
Note that the hook can (and should) be used irrespective of whether
being in Dom0, as accessing port 0x61 in a DomU would be even worse,
while the shared info field would just hold zero all the time. Note
further that hardware NMI handling for PVH doesn't currently work
anyway due to missing code in the hypervisor (but it is expected to
work the native rather than the PV way).
Signed-off-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Linus Torvalds [Tue, 13 Jan 2015 02:29:42 +0000 (15:29 +1300)]
Merge tag 'gpio-v3.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio fixes from Linus Walleij:
"Here are some GPIO fixes, mainly affecting the DLN2 IRQ handling.
Nothing special about them, just fixes:
- Three patches fixing IRQ handling for the DLN2
- Null pointer handling for grgpio"
* tag 'gpio-v3.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: dln2: use bus_sync_unlock instead of scheduling work
gpio: grgpio: Avoid potential NULL pointer dereference
gpio: dln2: Fix gpio output value in dln2_gpio_direction_output()
gpio: dln2: fix issue when an IRQ is unmasked then enabled
Linus Torvalds [Tue, 13 Jan 2015 02:25:23 +0000 (15:25 +1300)]
Merge tag 'mmc-v3.19-3' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC fixes from Ulf Hansson:
"MMC host:
- sdhci-pci|acpi: Support some new IDs
- sdhci: Fix sleep from atomic context
- sdhci-pxav3: Prevent hang during ->probe()
- sdhci: Disable re-tuning for HS400"
* tag 'mmc-v3.19-3' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: sdhci-pci: Add support for Intel SPT
mmc: sdhci-acpi: Add ACPI HID INT344D
mmc: sdhci: Fix sleep in atomic after inserting SD card
mmc: sdhci-pxav3: do the mbus window configuration after enabling clocks
mmc: sdhci: Disable re-tuning for HS400
mmc: sdhci: Simplify use of tuning timer
mmc: sdhci: Add out_unlock to sdhci_execute_tuning
mmc: sdhci: Tuning should not change max_blk_count
Pull scsi target fixes from Nicholas Bellinger:
"Mostly minor fixes this time, including:
- Add missing virtio-scsi -> TCM attribute conversion in vhost-scsi.
- Fix persistent reservations write exclusive handling to allow
readers for all registered I_T nexuses.
- Drop arbitrary maximum I/O size limit in order to process I/Os
larger than 4 MB, required for initiators that don't honor block
limits EVPD.
- Drop the now left-over fabric_max_sectors attribute"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: Fix typos in enum cmd_flags_table
MAINTAINERS: Add entry for iSER target driver
target: Allow Write Exclusive non-reservation holders to READ
target: Drop left-over fabric_max_sectors attribute
target: Drop arbitrary maximum I/O size limit
Documentation/target: Update fabric_ops to latest code
vhost-scsi: Add missing virtio-scsi -> TCM attribute conversion
Will Deacon [Mon, 12 Jan 2015 19:10:55 +0000 (19:10 +0000)]
mm: mmu_gather: use tlb->end != 0 only for TLB invalidation
When batching up address ranges for TLB invalidation, we check tlb->end
!= 0 to indicate that some pages have actually been unmapped.
As of commit f045bbb9fa1b ("mmu_gather: fix over-eager
tlb_flush_mmu_free() calling"), we use the same check for freeing these
pages in order to avoid a performance regression where we call
free_pages_and_swap_cache even when no pages are actually queued up.
Unfortunately, the range could have been reset (tlb->end = 0) by
tlb_end_vma, which has been shown to cause memory leaks on arm64.
Furthermore, investigation into these leaks revealed that the fullmm
case on task exit no longer invalidates the TLB, by virtue of tlb->end
== 0 (in 3.18, need_flush would have been set).
This patch resolves the problem by reverting commit f045bbb9fa1b, using
instead tlb->local.nr as the predicate for page freeing in
tlb_flush_mmu_free and ensuring that tlb->end is initialised to a
non-zero value in the fullmm case.
Tested-by: Mark Langsdorf <mlangsdo@redhat.com> Tested-by: Dave Hansen <dave@sr71.net> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
usb/kaweth: use GFP_ATOMIC under spin_lock in usb_start_wait_urb()
Commit e4c7f259c5be ("USB: kaweth.c: use GFP_ATOMIC under spin_lock")
makes sure that kaweth_internal_control_msg() allocates memory with GFP_ATOMIC,
but kaweth_internal_control_msg() also calls usb_start_wait_urb()
that still allocates memory with GFP_NOIO.
The patch fixes usb_start_wait_urb() as well.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Acked-by: Oliver Neukum <oliver@neukum.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon [Fri, 9 Jan 2015 20:29:40 +0000 (14:29 -0600)]
MAINTAINERS: add me as ibmveth maintainer
Adding myself as the ibmveth maintainer and replacing
Santiago Leon.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Cc: Santiago Leon <santi_leon@yahoo.com> Cc: Brian King <brking@linux.vnet.ibm.com> Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Thu, 8 Jan 2015 17:27:27 +0000 (12:27 -0500)]
tipc: fix bug in broadcast retransmit code
In commit 58dc55f25631178ee74cd27185956a8f7dcb3e32 ("tipc: use generic
SKB list APIs to manage link transmission queue") we replace all list
traversal loops with the macros skb_queue_walk() or
skb_queue_walk_safe(). While the previous loops were based on the
assumption that the list was NULL-terminated, the standard macros
stop when the iterator reaches the list head, which is non-NULL.
In the function bclink_retransmit_pkt() this macro replacement has
lead to a bug. When we receive a BCAST STATE_MSG we unconditionally
call the function bclink_retransmit_pkt(), whether there really is
anything to retransmit or not, assuming that the sequence number
comparisons will lead to the correct behavior. However, if the
transmission queue is empty, or if there are no eligible buffers in
the transmission queue, we will by mistake pass the list head pointer
to the function tipc_link_retransmit(). Since the list head is not a
valid sk_buff, this leads to a crash.
In this commit we fix this by only calling tipc_link_retransmit()
if we actually found eligible buffers in the transmission queue.
Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The clock is enabled without being prepared, this leads to:
WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:889 __clk_enable+0x24/0xa8()
and a non working ethernet interface.
Use clk_prepare_enable() and clk_disable_unprepare() to handle the clock.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
isdn: fix NUL (\0 or \x00) specification in string
In C one can either use '\0' or '\x00' (or '\000') to add a NUL byte to
a string. '\0x00' isn't part of these and will in fact result in a
single NUL followed by "x00". This fixes that.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Reported-at: http://www.viva64.com/en/b/0299/ Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Zyngier [Sun, 11 Jan 2015 13:10:11 +0000 (14:10 +0100)]
arm64: KVM: Fix HCR setting for 32bit guests
Commit b856a59141b1 (arm/arm64: KVM: Reset the HCR on each vcpu
when resetting the vcpu) moved the init of the HCR register to
happen later in the init of a vcpu, but left out the fixup
done in kvm_reset_vcpu when preparing for a 32bit guest.
As a result, the 32bit guest is run as a 64bit guest, but the
rest of the kernel still manages it as a 32bit. Fun follows.
Moving the fixup to vcpu_reset_hcr solves the problem for good.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Marc Zyngier [Sun, 11 Jan 2015 13:10:10 +0000 (14:10 +0100)]
arm64: KVM: Fix TLB invalidation by IPA/VMID
It took about two years for someone to notice that the IPA passed
to TLBI IPAS2E1IS must be shifted by 12 bits. Clearly our reviewing
is not as good as it should be...
Paper bag time for me.
Reported-by: Mario Smarduch <m.smarduch@samsung.com> Tested-by: Mario Smarduch <m.smarduch@samsung.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Juergen Gross [Mon, 12 Jan 2015 05:05:10 +0000 (06:05 +0100)]
xen: check for zero sized area when invalidating memory
With the introduction of the linear mapped p2m list setting memory
areas to "invalid" had to be delayed. When doing the invalidation
make sure no zero sized areas are processed.
Signed-off-by: Juegren Gross <jgross@suse.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Juergen Gross [Mon, 12 Jan 2015 05:05:08 +0000 (06:05 +0100)]
xen: correct race in alloc_p2m_pmd()
When allocating a new pmd for the linear mapped p2m list a check is
done for not introducing another pmd when this just happened on
another cpu. In this case the old pte pointer was returned which
points to the p2m_missing or p2m_identity page. The correct value
would be the pointer to the found new page.
Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Juergen Gross [Mon, 12 Jan 2015 05:05:07 +0000 (06:05 +0100)]
xen: correct error for building p2m list on 32 bits
In xen_rebuild_p2m_list() for large areas of invalid or identity
mapped memory the pmd entries on 32 bit systems are initialized
wrong. Correct this error.
Suggested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Jan Willeke [Thu, 8 Jan 2015 15:56:01 +0000 (16:56 +0100)]
s390/uprobes: fix user space PER events
If uprobes are single stepped for example with gdb, the behavior should
now be correct. Before this patch, when gdb was single stepping a uprobe,
the result was a SIGILL.
When PER is active for any storage alteration and a uprobe is hit, a storage
alteration event is indicated. These over indications are filterd out by gdb,
if no change has happened within the observed area.
Signed-off-by: Jan Willeke <willeke@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
mmc: sdhci: Fix sleep in atomic after inserting SD card
Sleep in atomic context happened on Trats2 board after inserting or
removing SD card because mmc_gpio_get_cd() was called under spin lock.
Fix this by moving card detection earlier, before acquiring spin lock.
The mmc_gpio_get_cd() call does not have to be protected by spin lock
because it does not access any sdhci internal data.
The sdhci_do_get_cd() call access host flags (SDHCI_DEVICE_DEAD). After
moving it out side of spin lock it could theoretically race with driver
removal but still there is no actual protection against manual card
eject.
Dmesg after inserting SD card:
[ 41.663414] BUG: sleeping function called from invalid context at drivers/gpio/gpiolib.c:1511
[ 41.670469] in_atomic(): 1, irqs_disabled(): 128, pid: 30, name: kworker/u8:1
[ 41.677580] INFO: lockdep is turned off.
[ 41.681486] irq event stamp: 61972
[ 41.684872] hardirqs last enabled at (61971): [<c0490ee0>] _raw_spin_unlock_irq+0x24/0x5c
[ 41.693118] hardirqs last disabled at (61972): [<c04907ac>] _raw_spin_lock_irq+0x18/0x54
[ 41.701190] softirqs last enabled at (61648): [<c0026fd4>] __do_softirq+0x234/0x2c8
[ 41.708914] softirqs last disabled at (61631): [<c00273a0>] irq_exit+0xd0/0x114
[ 41.716206] Preemption disabled at:[< (null)>] (null)
[ 41.721500]
[ 41.722985] CPU: 3 PID: 30 Comm: kworker/u8:1 Tainted: G W 3.18.0-rc5-next-20141121 #883
[ 41.732111] Workqueue: kmmcd mmc_rescan
[ 41.735945] [<c0014d2c>] (unwind_backtrace) from [<c0011c80>] (show_stack+0x10/0x14)
[ 41.743661] [<c0011c80>] (show_stack) from [<c0489d14>] (dump_stack+0x70/0xbc)
[ 41.750867] [<c0489d14>] (dump_stack) from [<c0228b74>] (gpiod_get_raw_value_cansleep+0x18/0x30)
[ 41.759628] [<c0228b74>] (gpiod_get_raw_value_cansleep) from [<c03646e8>] (mmc_gpio_get_cd+0x38/0x58)
[ 41.768821] [<c03646e8>] (mmc_gpio_get_cd) from [<c036d378>] (sdhci_request+0x50/0x1a4)
[ 41.776808] [<c036d378>] (sdhci_request) from [<c0357934>] (mmc_start_request+0x138/0x268)
[ 41.785051] [<c0357934>] (mmc_start_request) from [<c0357cc8>] (mmc_wait_for_req+0x58/0x1a0)
[ 41.793469] [<c0357cc8>] (mmc_wait_for_req) from [<c0357e68>] (mmc_wait_for_cmd+0x58/0x78)
[ 41.801714] [<c0357e68>] (mmc_wait_for_cmd) from [<c0361c00>] (mmc_io_rw_direct_host+0x98/0x124)
[ 41.810480] [<c0361c00>] (mmc_io_rw_direct_host) from [<c03620f8>] (sdio_reset+0x2c/0x64)
[ 41.818641] [<c03620f8>] (sdio_reset) from [<c035a3d8>] (mmc_rescan+0x254/0x2e4)
[ 41.826028] [<c035a3d8>] (mmc_rescan) from [<c003a0e0>] (process_one_work+0x180/0x3f4)
[ 41.833920] [<c003a0e0>] (process_one_work) from [<c003a3bc>] (worker_thread+0x34/0x4b0)
[ 41.841991] [<c003a3bc>] (worker_thread) from [<c003fed8>] (kthread+0xe4/0x104)
[ 41.849285] [<c003fed8>] (kthread) from [<c000f268>] (ret_from_fork+0x14/0x2c)
[ 42.038276] mmc0: new high speed SDHC card at address 1234
Thomas Petazzoni [Wed, 31 Dec 2014 10:54:10 +0000 (11:54 +0100)]
mmc: sdhci-pxav3: do the mbus window configuration after enabling clocks
In commit 5491ce3f79ee ("mmc: sdhci-pxav3: add support for the Armada
38x SDHCI controller"), the sdhci-pxav3 driver was extended to include
support for the SDHCI controller found in the Armada 38x
processor. This mainly involved adding some MBus window related
configuration.
However, this configuration is currently done too early in ->probe():
it is done before clocks are enabled, while this configuration
involves touching the registers of the controller, which will hang the
SoC if the clock is disabled. It wasn't noticed until now because the
bootloader typically leaves gatable clocks enabled, but in situations
where we have a deferred probe (due to a CD GPIO that cannot be taken,
for example), then the probe will be re-tried later, after a clock
disable has been done in the exit path of the failed probe attempt of
the device. This second probe() will hang the system due to the clock
being disabled.
This can for example be produced on Armada 385 GP, which has a CD GPIO
connected to an I2C PCA9555. If the driver for the PCA9555 is not
compiled into the kernel, then we will have the following sequence of
events:
1. The SDHCI probes
2. It does the MBus configuration (which works, because the clock is
left enabled by the bootloader)
3. It enables the clock
4. It tries to get the CD GPIO, which fails due to the driver being
missing, so -EPROBE_DEFER is returned.
5. Before returning -EPROBE_DEFER, the driver cleans up what was
done, which includes disabling the clock.
6. Later on, the SDHCI probe is tried again.
7. It does the MBus configuration, which hangs because the clock is
no longer enabled.
This commit does the obvious fix of doing the MBus configuration after
the clock has been enabled by the driver.
Fixes: 5491ce3f79ee ("mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller") Cc: <stable@vger.kernel.org> # v3.15+ Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter [Fri, 5 Dec 2014 17:25:31 +0000 (19:25 +0200)]
mmc: sdhci: Disable re-tuning for HS400
Re-tuning for HS400 mode must be done in HS200
mode. Currently there is no support for that.
That needs to be reflected in the code.
Specifically, if tuning is executed in HS400 mode
then return an error, and do not start the
tuning timer if HS200 tuning is being done prior
to switching to HS400.
Note that periodic re-tuning is not expected
to be needed for HS400 but re-tuning is still
needed after the host controller has lost power.
In the case of suspend/resume that is not necessary
because the card is fully re-initialised. That
just leaves runtime suspend/resume with no support
for HS400 re-tuning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter [Fri, 5 Dec 2014 17:25:30 +0000 (19:25 +0200)]
mmc: sdhci: Simplify use of tuning timer
The tuning timer is always used if the tuning mode
is 1 and there is a tuning count, irrespective of
whether this is the first call, or any subsequent
call. Consequently the logic to start the timer
can be simplified.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter [Fri, 5 Dec 2014 17:25:28 +0000 (19:25 +0200)]
mmc: sdhci: Tuning should not change max_blk_count
Re-tuning requires that the maximum data length
is limited to 4MiB. The code currently changes
max_blk_count in an attempt to achieve that.
This is wrong because max_blk_count is a different
limit, but it is also un-necessary because
max_req_size is 512KiB anyway. Consequently, the
changes to max_blk_count are removed and the
comment for max_req_size adjusted accordingly.
The comment is also tweaked to show that the 512KiB
limit is a SDMA limit not an ADMA limit.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
David S. Miller [Mon, 12 Jan 2015 05:23:45 +0000 (00:23 -0500)]
Merge tag 'wireless-drivers-for-davem-2015-01-09' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
* rtlwifi: fix a regression in large skb allocation failure
iwlwifi:
* fix for 7265D NVM check
* fixes for scan: fix long scanning times and network discovery
* new firmware API for iwlmvm supported devices
* fixes in rate control
Signed-off-by: David S. Miller <davem@davemloft.net>
Christoph Jaeger [Sun, 11 Jan 2015 18:01:16 +0000 (13:01 -0500)]
packet: bail out of packet_snd() if L2 header creation fails
Due to a misplaced parenthesis, the expression
(unlikely(offset) < 0),
which expands to
(__builtin_expect(!!(offset), 0) < 0),
never evaluates to true. Therefore, when sending packets with
PF_PACKET/SOCK_DGRAM, packet_snd() does not abort as intended
if the creation of the layer 2 header fails.
Spotted by Coverity - CID 1259975 ("Operands don't affect result").
Fixes: 9c7077622dd9 ("packet: make packet_snd fail on len smaller than l2 header") Signed-off-by: Christoph Jaeger <cj@linux.com> Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: Willem de Bruijn <willemb@google.com> Acked-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-eoan-kernel.git / log