We use skb->size with sk_rmem_scheduled() which is not correct. Instead
use truesize to align with socket and tcp stack usage of sk_rmem_schedule.
Suggested-by: Daniel Borkman <daniel@iogearbox.net> Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com> Link: https://lore.kernel.org/bpf/160556570616.73229.17003722112077507863.stgit@john-XPS-13-9370 Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
When we receive an skb and the ingress skb verdict program returns
SK_PASS we currently set the ingress flag and put it on the workqueue
so it can be turned into a sk_msg and put on the sk_msg ingress queue.
Then finally telling userspace with data_ready hook.
Here we observe that if the workqueue is empty then we can try to
convert into a sk_msg type and call data_ready directly without
bouncing through a workqueue. Its a common pattern to have a recv
verdict program for visibility that always returns SK_PASS. In this
case unless there is an ENOMEM error or we overrun the socket we
can avoid the workqueue completely only using it when we fall back
to error cases caused by memory pressure.
By doing this we eliminate another case where data may be dropped
if errors occur on memory limits in workqueue.
Fixes: 51199405f9672 ("bpf: skb_verdict, support SK_PASS on RX BPF path") Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/bpf/160226859704.5692.12929678876744977669.stgit@john-Precision-5820-Tower Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
For sk_skb case where skb_verdict program returns SK_PASS to continue to
pass packet up the stack, the memory limits were already checked before
enqueuing in skb_queue_tail from TCP side. So, lets remove the extra checks
here. The theory is if the TCP stack believes we have memory to receive
the packet then lets trust the stack and not double check the limits.
In fact the accounting here can cause a drop if sk_rmem_alloc has increased
after the stack accepted this packet, but before the duplicate check here.
And worse if this happens because TCP stack already believes the data has
been received there is no retransmit.
Fixes: 51199405f9672 ("bpf: skb_verdict, support SK_PASS on RX BPF path") Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/bpf/160226857664.5692.668205469388498375.stgit@john-Precision-5820-Tower Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Your maintainer committed a major braino in the rmap code by adding the
attr fork, bmbt, and unwritten extent usage bits into rmap record key
comparisons. While XFS uses the usage bits *in the rmap records* for
cross-referencing metadata in xfs_scrub and xfs_repair, it only needs
the owner and offset information to distinguish between reverse mappings
of the same physical extent into the data fork of a file at multiple
offsets. The other bits are not important for key comparisons for index
lookups, and never have been.
Eric Sandeen reports that this causes regressions in generic/299, so
undo this patch before it does more damage.
Reported-by: Eric Sandeen <sandeen@sandeen.net> Fixes: 6ff646b2ceb0 ("xfs: fix rmap key and record comparison functions") Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
At the start of driver initialization, we do not know what bias
setting the bootloader has configured the system for and we only know
for certain the very first time we do a transition.
However, since the initial value of the comparison index is -EINVAL,
this negative value results in an array out of bound access on the
very first transition.
Since we don't know what the setting is, we just set the bias
configuration as there is nothing to compare against. This prevents
the array out of bound access.
NOTE: Even though we could use a more relaxed check of "< 0" the only
valid values(ignoring cosmic ray induced bitflips) are -EINVAL, 0+.
In xfs_initialize_perag(), if kmem_zalloc(), xfs_buf_hash_init(), or
radix_tree_preload() failed, the returned value 'error' is not set
accordingly.
Reported-as-fixing: 8b26c5825e02 ("xfs: handle ENOMEM correctly during initialisation of perag structures") Fixes: 9b2471797942 ("xfs: cache unlinked pointers in an rhashtable") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yu Kuai <yukuai3@huawei.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
We always know the correct state of the rmap record flags (attr, bmbt,
unwritten) so check them by direct comparison.
Fixes: d852657ccfc0 ("xfs: cross-reference reverse-mapping btree") Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The comment and logic in xchk_btree_check_minrecs for dealing with
inode-rooted btrees isn't quite correct. While the direct children of
the inode root are allowed to have fewer records than what would
normally be allowed for a regular ondisk btree block, this is only true
if there is only one child block and the number of records don't fit in
the inode root.
Fixes: 08a3a692ef58 ("xfs: btree scrub should check minrecs") Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Avoid processing bogus interrupt statuses when the HW is runtime suspended and
the M_CAN_IR register read may get all bits 1's. Handler can be called if the
interrupt request is shared with other peripherals or at the end of free_irq().
Therefore check the runtime suspended status before processing.
Fixes: cdf8259d6573 ("can: m_can: Add PM Support") Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Link: https://lore.kernel.org/r/20200915134715.696303-1-jarkko.nikula@linux.intel.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
If the CAN controller goes into bus off, the do_set_mode() callback with
CAN_MODE_START can be used to recover the controller, which then calls
flexcan_chip_start(). If configured, this is done automatically by the
framework or manually by the user.
In flexcan_chip_start() there is an explicit call to
flexcan_transceiver_enable(), which does a regulator_enable() on the
transceiver regulator. This results in a net usage counter increase, as there
is no corresponding flexcan_transceiver_disable() in the bus off code path.
This further leads to the transceiver stuck enabled, even if the CAN interface
is shut down.
To fix this problem the
flexcan_transceiver_enable()/flexcan_transceiver_disable() are moved out of
flexcan_chip_start()/flexcan_chip_stop() into flexcan_open()/flexcan_close().
Fixes: e955cead0311 ("CAN: Add Flexcan CAN controller driver") Link: https://lore.kernel.org/r/20201118150148.2664024-1-mkl@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Use correct bittiming limits for the KCAN CAN controller.
Fixes: aec5fb2268b7 ("can: kvaser_usb: Add support for Kvaser USB hydra family") Signed-off-by: Jimmy Assarsson <extja@kvaser.com> Link: https://lore.kernel.org/r/20201115163027.16851-2-jimmyassarsson@gmail.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Fix sockmap sk_skb programs so that they observe sk_rcvbuf limits. This
allows users to tune SO_RCVBUF and sockmap will honor them.
We can refactor the if(charge) case out in later patches. But, keep this
fix to the point.
Fixes: 51199405f9672 ("bpf: skb_verdict, support SK_PASS on RX BPF path") Suggested-by: Jakub Sitnicki <jakub@cloudflare.com> Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com> Link: https://lore.kernel.org/bpf/160556568657.73229.8404601585878439060.stgit@john-XPS-13-9370 Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
If copy_page_to_iter() fails or even partially completes, but with fewer
bytes copied than expected we currently reset sg.start and return EFAULT.
This proves problematic if we already copied data into the user buffer
before we return an error. Because we leave the copied data in the user
buffer and fail to unwind the scatterlist so kernel side believes data
has been copied and user side believes data has _not_ been received.
Expected behavior should be to return number of bytes copied and then
on the next read we need to return the error assuming its still there. This
can happen if we have a copy length spanning multiple scatterlist elements
and one or more complete before the error is hit.
The error is rare enough though that my normal testing with server side
programs, such as nginx, httpd, envoy, etc., I have never seen this. The
only reliable way to reproduce that I've found is to stream movies over
my browser for a day or so and wait for it to hang. Not very scientific,
but with a few extra WARN_ON()s in the code the bug was obvious.
When we review the errors from copy_page_to_iter() it seems we are hitting
a page fault from copy_page_to_iter_iovec() where the code checks
fault_in_pages_writeable(buf, copy) where buf is the user buffer. It
also seems typical server applications don't hit this case.
The other way to try and reproduce this is run the sockmap selftest tool
test_sockmap with data verification enabled, but it doesn't reproduce the
fault. Perhaps we can trigger this case artificially somehow from the
test tools. I haven't sorted out a way to do that yet though.
Fixes: 604326b41a6fb ("bpf, sockmap: convert to generic sk_msg interface") Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com> Link: https://lore.kernel.org/bpf/160556566659.73229.15694973114605301063.stgit@john-XPS-13-9370 Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 65b4414a05eb ("selftests/bpf: add sockopt test that exercises BPF_F_ALLOW_MULTI") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20201116101633.64627-1-wanghai38@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
There might be some requests pending in the buffer when the interface close
sequence occurs. In some devices, these pending requests might lead to the
module not shutting down properly when m_can_clk_stop() is called.
Therefore, move the device to init state before potentially powering it down.
Fixes: e0d1f4816f2a ("can: m_can: add Bosch M_CAN controller support") Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Acked-by: Dan Murphy <dmurphy@ti.com> Link: https://lore.kernel.org/r/20200825055442.16994-1-faiz_abbas@ti.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
This patch creates a common function that peripherials can call to free the
netdev device when failures occur.
Fixes: f524f829b75a ("can: m_can: Create a m_can platform framework") Reported-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Dan Murphy <dmurphy@ti.com> Link: http://lore.kernel.org/r/20200227183829.21854-2-dmurphy@ti.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Change the order in tcan4x5x_can_remove() to be the exact inverse of
tcan4x5x_can_probe(). First m_can_class_unregister(), then power down the
device.
Fixes: 5443c226ba91 ("can: tcan4x5x: Add tcan4x5x driver to the kernel") Cc: Dan Murphy <dmurphy@ti.com> Link: http://lore.kernel.org/r/20201019154233.1262589-10-mkl@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
This patch adds the missing error checking when initializing the regmap
interface fails.
Fixes: 5443c226ba91 ("can: tcan4x5x: Add tcan4x5x driver to the kernel") Cc: Dan Murphy <dmurphy@ti.com> Link: http://lore.kernel.org/r/20201019154233.1262589-7-mkl@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
regmap is a library function that gets selected by drivers that need it. No
driver modules should depend on it. Instead depends on SPI and select
REGMAP_SPI. Depending on REGMAP_SPI makes this driver only build if another
driver already selected REGMAP_SPI, as the symbol can't be selected through the
menu kernel configuration.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Link: http://lore.kernel.org/r/20200413141013.506613-1-enric.balletbo@collabora.com Reviewed-by: Dan Murphy <dmurphy@ti.com> Fixes: 5443c226ba91 ("can: tcan4x5x: Add tcan4x5x driver to the kernel") Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
pm_runtime_get_sync() will increment pm usage at first and it will resume the
device later. If runtime of the device has error or device is in inaccessible
state(or other error state), resume operation will fail. If we do not call put
operation to decrease the reference, it will result in reference leak in the
two functions flexcan_get_berr_counter() and flexcan_open().
Moreover, this device cannot enter the idle state and always stay busy or other
non-idle state later. So we should fix it through adding
pm_runtime_put_noidle().
Fixes: ca10989632d88 ("can: flexcan: implement can Runtime PM") Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com> Link: https://lore.kernel.org/r/20201108083000.2599705-1-zhangqilong3@huawei.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The left shift of int 32 bit integer constant 1 is evaluated using 32 bit
arithmetic and then assigned to a signed 64 bit variable. In the case where
time_ref->adapter->ts_used_bits is 32 or more this can lead to an oveflow.
Avoid this by shifting using the BIT_ULL macro instead.
Fixes: bb4785551f64 ("can: usb: PEAK-System Technik USB adapters driver core") Signed-off-by: Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20201105112427.40688-1-colin.king@canonical.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The driver has to first fill the skb with data and then handle it to
can_put_echo_skb(). This patch moves the can_put_echo_skb() down, right before
sending the skb out via USB.
Fixes: 51f3baad7de9 ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer") Cc: Remigiusz Kołłątaj <remigiusz.kollataj@mobica.com> Link: https://lore.kernel.org/r/20201111221204.1639007-1-mkl@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
In the error handling, we should goto the probe_exit_candev
to free ndev to prevent memory leak.
Fixes: dabf54dd1c63 ("can: ti_hecc: Convert TI HECC driver to DT only driver") Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com> Link: https://lore.kernel.org/r/20201114111708.3465543-1-zhangqilong3@huawei.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
netif_rx() is meant to be called from interrupt contexts. can_restart() may be
called by can_restart_work(), which is called from a worqueue, so it may run in
process context. Use netif_rx_ni() instead.
Fixes: 39549eef3587 ("can: CAN Network device driver and Netlink interface") Co-developed-by: Loris Fauster <loris.fauster@ttcontrol.com> Signed-off-by: Loris Fauster <loris.fauster@ttcontrol.com> Signed-off-by: Alejandro Concepcion Rodriguez <alejandro@acoro.eu> Link: https://lore.kernel.org/r/4e84162b-fb31-3a73-fa9a-9438b4bd5234@acoro.eu
[mkl: use netif_rx_ni() instead of netif_rx_any_context()] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
In canfd_rcv(), cfd->len is uninitialized when skb->len = 0, and this
uninitialized cfd->len is accessed nonetheless by pr_warn_once().
Fix this uninitialized variable access by checking cfd->len's validity
condition (cfd->len > CANFD_MAX_DLEN) separately after the skb->len's
condition is checked, and appropriately modify the log messages that
are generated as well.
In case either of the required conditions fail, the skb is freed and
NET_RX_DROP is returned, same as before.
Fixes: d4689846881d ("can: af_can: canfd_rcv(): replace WARN_ONCE by pr_warn_once") Reported-by: syzbot+9bcb0c9409066696d3aa@syzkaller.appspotmail.com Tested-by: Anant Thazhemadam <anant.thazhemadam@gmail.com> Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com> Link: https://lore.kernel.org/r/20201103213906.24219-3-anant.thazhemadam@gmail.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
In can_rcv(), cfd->len is uninitialized when skb->len = 0, and this
uninitialized cfd->len is accessed nonetheless by pr_warn_once().
Fix this uninitialized variable access by checking cfd->len's validity
condition (cfd->len > CAN_MAX_DLEN) separately after the skb->len's
condition is checked, and appropriately modify the log messages that
are generated as well.
In case either of the required conditions fail, the skb is freed and
NET_RX_DROP is returned, same as before.
Fixes: 8cb68751c115 ("can: af_can: can_rcv(): replace WARN_ONCE by pr_warn_once") Reported-by: syzbot+9bcb0c9409066696d3aa@syzkaller.appspotmail.com Tested-by: Anant Thazhemadam <anant.thazhemadam@gmail.com> Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com> Link: https://lore.kernel.org/r/20201103213906.24219-2-anant.thazhemadam@gmail.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Currently, we may set the tunnel option flag when the size of metadata
is zero. For example, we set TUNNEL_GENEVE_OPT in the receive function
no matter the geneve option is present or not. As this may result in
issues on the tunnel flags consumers, this patch fixes the issue.
Related discussion:
* https://lore.kernel.org/netdev/1604448694-19351-1-git-send-email-yihung.wei@gmail.com/T/#u
Fixes: 256c87c17c53 ("net: check tunnel option type in tunnel flags") Signed-off-by: Yi-Hung Wei <yihung.wei@gmail.com> Link: https://lore.kernel.org/r/1605053800-74072-1-git-send-email-yihung.wei@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
progfd is created by prog_parse_fd() in do_attach() and before the latter
returns in case of success, the file descriptor should be closed.
Fixes: 04949ccc273e ("tools: bpftool: add net attach command to attach XDP on interface") Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20201113115152.53178-1-wanghai38@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
This is an imbalance issue. The locking sequence structure
"lock_seq_stat" contains the reader counter and it is used to check if
the locking sequence is balance or not between acquiring and releasing.
If the tool wrongly frees "lock_seq_stat" when "read_count" isn't zero,
the "read_count" will be reset to zero when allocate a new structure at
the next time; thus it causes the wrong counting for reader and finally
results in imbalance issue.
To fix this issue, if detects "read_count" is not zero (means still have
read user in the locking sequence), goto the "end" tag to skip freeing
structure "lock_seq_stat".
Fixes: e4cef1f65061 ("perf lock: Fix state machine to recognize lock sequence") Signed-off-by: Leo Yan <leo.yan@linaro.org> Acked-by: Jiri Olsa <jolsa@redhat.com> Link: https://lore.kernel.org/r/20201104094229.17509-2-leo.yan@linaro.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
dma_virt_ops requires that all pages have a kernel virtual address.
Introduce a INFINIBAND_VIRT_DMA Kconfig symbol that depends on !HIGHMEM
and make all three drivers depend on the new symbol.
Also remove the ARCH_DMA_ADDR_T_64BIT dependency, which has been obsolete
since commit 4965a68780c5 ("arch: define the ARCH_DMA_ADDR_T_64BIT config
symbol in lib/Kconfig")
Fixes: 551199aca1c3 ("lib/dma-virt: Add dma_virt_ops") Link: https://lore.kernel.org/r/20201106181941.1878556-2-hch@lst.de Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Fix missing kfree in pvrdma_register_device() when failure from
ib_device_set_netdev().
Fixes: 4b38da75e089 ("RDMA/drivers: Convert easy drivers to use ib_device_set_netdev()") Link: https://lore.kernel.org/r/20201111032202.17925-1-miaoqinglang@huawei.com Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
If a device is getting removed or reprobed during resume, use-after-free
might happen. For example, h5_btrtl_resume() schedules a work queue for
device reprobing, which of course requires removal first.
If the removal happens in parallel with the device_resume() and wins the
race to acquire device_lock(), removal may remove the device from the PM
lists and all, but device_resume() is already running and will continue
when the lock can be acquired, thus calling rfkill_resume().
During this, if rfkill_set_block() is then called after the corresponding
*_unregister() and kfree() are called, there will be an use-after-free
in hci_rfkill_set_block():
Fix this by checking rfkill->registered in rfkill_resume(). device_del()
in rfkill_unregister() requires device_lock() and the whole rfkill_resume()
is also protected by the same lock via device_resume(), we can make sure
either the rfkill->registered is false before rfkill_resume() starts or the
rfkill device won't be unregistered before rfkill_resume() returns.
As async_resume() holds a reference to the device, at this level there can
be no use-after-free; only in the user that doesn't expect this scenario.
Fixes: 8589086f4efd ("Bluetooth: hci_h5: Turn off RTL8723BS on suspend, reprobe on resume") Signed-off-by: Claire Chang <tientzu@chromium.org> Link: https://lore.kernel.org/r/20201110084908.219088-1-tientzu@chromium.org
[edit commit message for clarity and add more info provided later] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
When TOUCHSCREEN_ADC is enabled and IIO_BUFFER is disabled, it results
in the following Kbuild warning:
WARNING: unmet direct dependencies detected for IIO_BUFFER_CB
Depends on [n]: IIO [=y] && IIO_BUFFER [=n]
Selected by [y]:
- TOUCHSCREEN_ADC [=y] && !UML && INPUT [=y] && INPUT_TOUCHSCREEN [=y] && IIO [=y]
The reason is that TOUCHSCREEN_ADC selects IIO_BUFFER_CB without depending
on or selecting IIO_BUFFER while IIO_BUFFER_CB depends on IIO_BUFFER. This
can also fail building the kernel.
Honor the kconfig dependency to remove unmet direct dependency warnings
and avoid any potential build failures.
Fixes: aa132ffb6b0a ("input: touchscreen: resistive-adc-touch: add generic resistive ADC touchscreen") Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com> Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Link: https://lore.kernel.org/r/20201102221504.541279-1-fazilyildiran@gmail.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
After merging the drm-misc tree, linux-next build (arm
multi_v7_defconfig) failed like this:
In file included from drivers/gpu/drm/nouveau/nouveau_ttm.c:26:
include/linux/swiotlb.h: In function 'swiotlb_max_mapping_size':
include/linux/swiotlb.h:99:9: error: 'SIZE_MAX' undeclared (first use in this function)
99 | return SIZE_MAX;
| ^~~~~~~~
include/linux/swiotlb.h:7:1: note: 'SIZE_MAX' is defined in header '<stdint.h>'; did you forget to '#include <stdint.h>'?
6 | #include <linux/init.h>
+++ |+#include <stdint.h>
7 | #include <linux/types.h>
include/linux/swiotlb.h:99:9: note: each undeclared identifier is reported only once for each function it appears in
99 | return SIZE_MAX;
| ^~~~~~~~
but only exposed by commit "drm/nouveu: fix swiotlb include"
Fix it by including linux/limits.h as appropriate.
Fixes: abe420bfae52 ("swiotlb: Introduce swiotlb_max_mapping_size()") Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Link: https://lore.kernel.org/r/20201102124327.2f82b2a7@canb.auug.org.au Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Commit bcf3440c6dd7 ("net: phy: micrel: add phy-mode support for the
KSZ9031 PHY") fixed micrel phy driver adding proper support for phy
modes. Adapt imx6q-udoo board phy settings : explicitly set required
delay configuration using "rgmii-id".
Fixes: cbd54fe0b2bc ("ARM: dts: imx6dl-udoo: Add board support based off imx6q-udoo") Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The "revid" is used to store negative error codes so it should be an int
type.
Fixes: e27c729219ad ("Input: add driver for ADXL345/346 Digital Accelerometers") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Michael Hennerich <michael.hennerich@analog.com> Link: https://lore.kernel.org/r/20201026072824.GA1620546@mwanda Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The Ethernet PHY on the Bananapi M64 has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
The Ethernet PHY on the Bananapi M2+ has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 8c7ba536e709 ("ARM: sun8i: bananapi-m2-plus: Enable dwmac-sun8i") Fixes: 4904337fe34f ("ARM: dts: sunxi: Restore EMAC changes (boards)") Fixes: aa8fee415f46 ("ARM: dts: sun8i: h3: Split out non-SoC-specific parts of Bananapi M2 Plus") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Tested-by: Jernej Skrabec <jernej.skrabec@siol.net> Acked-by: Jernej Skrabec <jernej.skrabec@siol.net> Link: https://lore.kernel.org/r/20201024162515.30032-8-wens@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The Ethernet PHY on the Cubieboard 4 and A80 Optimus have the RX
and TX delays enabled on the PHY, using pull-ups on the RXDLY and
TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
The Ethernet PHY on the Bananapi M3 and Cubietruck Plus have the RX
and TX delays enabled on the PHY, using pull-ups on the RXDLY and
TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 039359948a4b ("ARM: dts: sun8i: a83t: Enable Ethernet on two boards") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Acked-by: Jernej Skrabec <jernej.skrabec@siol.net> Link: https://lore.kernel.org/r/20201024162515.30032-6-wens@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The Ethernet PHY on the Orange Pi Plus 2E has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 4904337fe34f ("ARM: dts: sunxi: Restore EMAC changes (boards)") Fixes: 7a78ef92cdc5 ("ARM: sun8i: h3: Enable EMAC with external PHY on Orange Pi Plus 2E") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Tested-by: Jernej Skrabec <jernej.skrabec@siol.net> Acked-by: Jernej Skrabec <jernej.skrabec@siol.net> Link: https://lore.kernel.org/r/20201024162515.30032-5-wens@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The Ethernet PHY on the Bananapi M1+ has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 04c85ecad32a ("ARM: dts: sun7i: Add dts file for Bananapi M1 Plus board") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Acked-by: Jernej Skrabec <jernej.skrabec@siol.net> Link: https://lore.kernel.org/r/20201024162515.30032-4-wens@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The Ethernet PHY on the Cubietruck has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 67073d97672d ("ARM: dts: sun7i: cubietruck: Enable the GMAC") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Tested-by: Emilio López <emilio@elopez.com.ar> Reviewed-by: Emilio López <emilio@elopez.com.ar> Link: https://lore.kernel.org/r/20201024162515.30032-3-wens@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The Ethernet PHY on the A31 Hummingbird has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: c220aec2bb79 ("ARM: dts: sun6i: Add Merrii A31 Hummingbird support") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Acked-by: Jernej Skrabec <jernej.skrabec@siol.net> Link: https://lore.kernel.org/r/20201024162515.30032-2-wens@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
According to board schematic, PHY provides both, RX and TX delays.
However, according to "fix" Realtek provided for this board, only TX
delay should be provided by PHY.
Tests show that both variants work but TX only PHY delay works
slightly better.
Update ethernet node to reflect the fact that PHY provides TX delay.
Fixes: 94f442886711 ("arm64: dts: allwinner: A64: Restore EMAC changes") Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20201022211301.3548422-1-jernej.skrabec@siol.net Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Since commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx delay config"),
the network is unusable on PineH64 model A.
This is due to phy-mode incorrectly set to rgmii instead of rgmii-id.
Fixes: 729e1ffcf47e ("arm64: allwinner: h6: add support for the Ethernet on Pine H64") Signed-off-by: Corentin Labbe <clabbe@baylibre.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20201019063449.33316-1-clabbe@baylibre.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Before the commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), the software overwrite for RX/TX delays of the RTL8211e
were not working properly and the Beelink GS1 had both RX/TX delay of RGMII
interface set using pull-up on the TXDLY and RXDLY pins.
Now that these delays are working properly they overwrite the HW
config and set this to 'rgmii' meaning no delay on both RX/TX.
This makes the ethernet of this board not working anymore.
Set the phy-mode to 'rgmii-id' meaning RGMII with RX/TX delays
in the device-tree to keep the correct configuration.
Fixes: 089bee8dd119 ("arm64: dts: allwinner: h6: Introduce Beelink GS1 board") Signed-off-by: Clément Péron <peron.clem@gmail.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Acked-by: Chen-Yu Tsai <wens@csie.org> Link: https://lore.kernel.org/r/20201018172409.1754775-1-peron.clem@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
To convert the number of pulses counted into an RPM estimation, we need
to divide by the width of our measurement interval instead of
multiplying by it. If the width of the measurement interval is zero we
don't update the RPM value to avoid dividing by zero.
We also don't need to do 64-bit division, with 32-bits we can handle a
fan running at over 4 million RPM.
Signed-off-by: Paul Barker <pbarker@konsulko.com> Link: https://lore.kernel.org/r/20201111164643.7087-1-pbarker@konsulko.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
In the fail path of gfs2_check_blk_type, forgetting to call
gfs2_glock_dq_uninit will result in rgd_gh reference leak.
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
__sb_start_write has some weird looking lockdep code that claims to
exist to handle nested freeze locking requests from xfs. The code as
written seems broken -- if we think we hold a read lock on any of the
higher freeze levels (e.g. we hold SB_FREEZE_WRITE and are trying to
lock SB_FREEZE_PAGEFAULT), it converts a blocking lock attempt into a
trylock.
However, it's not correct to downgrade a blocking lock attempt to a
trylock unless the downgrading code or the callers are prepared to deal
with that situation. Neither __sb_start_write nor its callers handle
this at all. For example:
sb_start_pagefault ignores the return value completely, with the result
that if xfs_filemap_fault loses a race with a different thread trying to
fsfreeze, it will proceed without pagefault freeze protection (thereby
breaking locking rules) and then unlocks the pagefault freeze lock that
it doesn't own on its way out (thereby corrupting the lock state), which
leads to a system hang shortly afterwards.
Normally, this won't happen because our ownership of a read lock on a
higher freeze protection level blocks fsfreeze from grabbing a write
lock on that higher level. *However*, if lockdep is offline,
lock_is_held_type unconditionally returns 1, which means that
percpu_rwsem_is_held returns 1, which means that __sb_start_write
unconditionally converts blocking freeze lock attempts into trylocks,
even when we *don't* hold anything that would block a fsfreeze.
Apparently this all held together until 5.10-rc1, when bugs in lockdep
caused lockdep to shut itself off early in an fstests run, and once
fstests gets to the "race writes with freezer" tests, kaboom. This
might explain the long trail of vanishingly infrequent livelocks in
fstests after lockdep goes offline that I've never been able to
diagnose.
We could fix it by spinning on the trylock if wait==true, but AFAICT the
locking works fine if lockdep is not built at all (and I didn't see any
complaints running fstests overnight), so remove this snippet entirely.
NOTE: Commit f4b554af9931 in 2015 created the current weird logic (which
used to exist in a different form in commit 5accdf82ba25c from 2012) in
__sb_start_write. XFS solved this whole problem in the late 2.6 era by
creating a variant of transactions (XFS_TRANS_NO_WRITECOUNT) that don't
grab intwrite freeze protection, thus making lockdep's solution
unnecessary. The commit claims that Dave Chinner explained that the
trylock hack + comment could be removed, but nobody ever did.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Commit ce3d31ad3cac ("arm64/smp: Move rcu_cpu_starting() earlier") ensured
that RCU is informed early about incoming CPUs that might end up calling
into printk() before they are online. However, if such a CPU fails the
early CPU feature compatibility checks in check_local_cpu_capabilities(),
then it will be powered off or parked without informing RCU, leading to
an endless stream of stalls:
| rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
| rcu: 2-O...: (0 ticks this GP) idle=002/1/0x4000000000000000 softirq=0/0 fqs=2593
| (detected by 0, t=5252 jiffies, g=9317, q=136)
| Task dump for CPU 2:
| task:swapper/2 state:R running task stack: 0 pid: 0 ppid: 1 flags:0x00000028
| Call trace:
| ret_from_fork+0x0/0x30
Ensure that the dying CPU invokes rcu_report_dead() prior to being powered
off or parked.
cpu_psci_cpu_die() is called in the context of the dying CPU, which
will no longer be online or tracked by RCU. It is therefore not generally
safe to call printk() if the PSCI "cpu off" request fails, so remove the
pr_crit() invocation.
Cc: Qian Cai <cai@redhat.com> Cc: "Paul E. McKenney" <paulmck@kernel.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Link: https://lore.kernel.org/r/20201106103602.9849-2-will@kernel.org Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
In a surprising turn of events, it transpires that CPU capabilities
configured as ARM64_CPUCAP_WEAK_LOCAL_CPU_FEATURE are never set as the
result of late-onlining. Therefore our handling of erratum 1418040 does
not get activated if it is not required by any of the boot CPUs, even
though we allow late-onlining of an affected CPU.
In order to get things working again, replace the cpus_have_const_cap()
invocation with an explicit check for the current CPU using
this_cpu_has_cap().
Cc: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org> Cc: Stephen Boyd <swboyd@chromium.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com> Acked-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20201106114952.10032-1-will@kernel.org Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The Medion Akoya E2228T's ACPI _LID implementation is quite broken,
it has the same issues as the one from the Medion Akoya E2215T:
1. For notifications it uses an ActiveLow Edge GpioInt, rather then
an ActiveBoth one, meaning that the device is only notified when the
lid is closed, not when it is opened.
2. Matching with this its _LID method simply always returns 0 (closed)
In order for the Linux LID code to work properly with this implementation,
the lid_init_state selection needs to be set to ACPI_BUTTON_LID_INIT_OPEN,
add a DMI quirk for this.
While working on this I also found out that the MD60### part of the model
number differs per country/batch while all of the E2215T and E2228T models
have this issue, so also remove the " MD60198" part from the E2215T quirk.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Fix the layout of 'struct desc64' to match the layout described in the
SDM Vol 3, Chapter 3 "Protected-Mode Memory Management", section 3.4.5
"Segment Descriptors", Figure 3-8 "Segment Descriptor". The test added
later in this series relies on this and crashes if this layout is not
correct.
Signed-off-by: Aaron Lewis <aaronlewis@google.com> Reviewed-by: Alexander Graf <graf@amazon.com>
Message-Id: <20201012194716.3950330-2-aaronlewis@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The scsi_block_reqs_cnt increased in ufshcd_hold() is supposed to be
decreased back in ufshcd_ungate_work() in a paired way. However, if
specific ufshcd_hold/release sequences are met, it is possible that
scsi_block_reqs_cnt is increased twice but only one ungate work is
queued. To make sure scsi_block_reqs_cnt is handled by ufshcd_hold() and
ufshcd_ungate_work() in a paired way, increase it only if queue_work()
returns true.
Link: https://lore.kernel.org/r/1604384682-15837-2-git-send-email-cang@codeaurora.org Reviewed-by: Hongwu Su <hongwus@codeaurora.org> Reviewed-by: Stanley Chu <stanley.chu@mediatek.com> Reviewed-by: Bean Huo <beanhuo@micron.com> Signed-off-by: Can Guo <cang@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
When removing the driver we would hit BUG_ON(!list_empty(&dev->ptype_specific))
in net/core/dev.c due to still having the NC-SI packet handler
registered.
Fixes: bd466c3fb5a4 ("net/faraday: Support NCSI mode") Signed-off-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20201117024448.1170761-1-joel@jms.id.au Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
If a user unbinds and re-binds a NC-SI aware driver the kernel will
attempt to register the netlink interface at runtime. The structure is
marked __ro_after_init so registration fails spectacularly at this point.
Jakub pointed out that ncsi_register_dev is obviously broken, because
there is only one family so it would never work if there was more than
one ncsi netdev.
Fix the crash by registering the netlink family once on boot, and drop
the code to unregister it.
Fixes: 955dc68cb9b2 ("net/ncsi: Add generic netlink family") Signed-off-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Link: https://lore.kernel.org/r/20201112061210.914621-1-joel@jms.id.au Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
LTE module MR400 embedded in TL-MR6400 v4 requires DTR to be set.
Signed-off-by: Filip Moc <dev@moc6.cz> Acked-by: Bjørn Mork <bjorn@mork.no> Link: https://lore.kernel.org/r/20201117173631.GA550981@moc6.cz Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Currently when QoS is enabled for VF and any min_rate is configured,
the driver sets bw_share value to at least 1 and doesn’t allow to set
it to 0 to make minimal rate unlimited. It means there is always a
minimal rate configured for every VF, even if user tries to remove it.
In order to make QoS disable possible, check whether all vports have
configured min_rate = 0. If this is true, set their bw_share to 0 to
disable min_rate limitations.
Fixes: c9497c98901c ("net/mlx5: Add support for setting VF min rate") Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Fixes: a7ee18bdee83 ("RDMA/mlx5: Allow creating a matcher for a NIC TX flow table") Signed-off-by: Michael Guralnik <michaelgur@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Reviewed-by: Maor Gottlieb <maorg@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
During loss recovery, retransmitted packets are forced to use TCP
timestamps to calculate the RTT samples, which have a millisecond
granularity. BBR is designed using a microsecond granularity. As a
result, multiple RTT samples could be truncated to the same RTT value
during loss recovery. This is problematic, as BBR will not enter
PROBE_RTT if the RTT sample is <= the current min_rtt sample, meaning
that if there are persistent losses, PROBE_RTT will constantly be
pushed off and potentially never re-entered. This patch makes sure
that BBR enters PROBE_RTT by checking if RTT sample is < the current
min_rtt sample, rather than <=.
The Netflix transport/TCP team discovered this bug in the Linux TCP
BBR code during lab tests.
Fixes: 0f8782ea1497 ("tcp_bbr: add BBR congestion control") Signed-off-by: Ryan Sharpelletti <sharpelletti@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Link: https://lore.kernel.org/r/20201116174412.1433277-1-sharpelletti.kdev@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
This is because it holds asoc when transport->proto_unreach_timer starts
and puts asoc when the timer stops, and without holding transport the
transport could be freed when the timer is still running.
So fix it by holding/putting transport instead for proto_unreach_timer
in transport, just like other timers in transport.
v1->v2:
- Also use sctp_transport_put() for the "out_unlock:" path in
sctp_generate_proto_unreach_event(), as Marcelo noticed.
Fixes: 50b5d6ad6382 ("sctp: Fix a race between ICMP protocol unreachable and connect()") Reported-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Link: https://lore.kernel.org/r/102788809b554958b13b95d33440f5448113b8d6.1605331373.git.lucien.xin@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 3ced0a88cd4c ("qlcnic: Add support to run firmware POST") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Link: https://lore.kernel.org/r/1605248186-16013-1-git-send-email-zhangchangzhong@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 469981b17a4f ("qed: Add unaligned and packed packet processing") Fixes: fcb39f6c10b2 ("qed: Add mpa buffer descriptors for storing and processing mpa fpdus") Fixes: 1e28eaad07ea ("qed: Add iWARP support for fpdu spanned over more than two tcp packets") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Acked-by: Michal Kalderon <michal.kalderon@marvell.com> Link: https://lore.kernel.org/r/1605532033-27373-1-git-send-email-zhangchangzhong@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The ethernet driver may allocate skb (and skb->data) via napi_alloc_skb().
This ends up to page_frag_alloc() to allocate skb->data from
page_frag_cache->va.
During the memory pressure, page_frag_cache->va may be allocated as
pfmemalloc page. As a result, the skb->pfmemalloc is always true as
skb->data is from page_frag_cache->va. The skb will be dropped if the
sock (receiver) does not have SOCK_MEMALLOC. This is expected behaviour
under memory pressure.
However, once kernel is not under memory pressure any longer (suppose large
amount of memory pages are just reclaimed), the page_frag_alloc() may still
re-use the prior pfmemalloc page_frag_cache->va to allocate skb->data. As a
result, the skb->pfmemalloc is always true unless page_frag_cache->va is
re-allocated, even if the kernel is not under memory pressure any longer.
Here is how kernel runs into issue.
1. The kernel is under memory pressure and allocation of
PAGE_FRAG_CACHE_MAX_ORDER in __page_frag_cache_refill() will fail. Instead,
the pfmemalloc page is allocated for page_frag_cache->va.
2: All skb->data from page_frag_cache->va (pfmemalloc) will have
skb->pfmemalloc=true. The skb will always be dropped by sock without
SOCK_MEMALLOC. This is an expected behaviour.
3. Suppose a large amount of pages are reclaimed and kernel is not under
memory pressure any longer. We expect skb->pfmemalloc drop will not happen.
4. Unfortunately, page_frag_alloc() does not proactively re-allocate
page_frag_alloc->va and will always re-use the prior pfmemalloc page. The
skb->pfmemalloc is always true even kernel is not under memory pressure any
longer.
Fix this by freeing and re-allocating the page instead of recycling it.
References: https://lore.kernel.org/lkml/20201103193239.1807-1-dongli.zhang@oracle.com/
References: https://lore.kernel.org/linux-mm/20201105042140.5253-1-willy@infradead.org/ Suggested-by: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Aruna Ramakrishna <aruna.ramakrishna@oracle.com> Cc: Bert Barbe <bert.barbe@oracle.com> Cc: Rama Nichanamatlu <rama.nichanamatlu@oracle.com> Cc: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com> Cc: Manjunath Patil <manjunath.b.patil@oracle.com> Cc: Joe Jin <joe.jin@oracle.com> Cc: SRINIVAS <srinivas.eeda@oracle.com> Fixes: 79930f5892e1 ("net: do not deplete pfmemalloc reserve") Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20201115201029.11903-1-dongli.zhang@oracle.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The x25_disconnect function in x25_subr.c would decrease the refcount of
"x25->neighbour" (struct x25_neigh) and reset this pointer to NULL.
However, the x25_rx_call_request function in af_x25.c, which is called
when we receive a connection request, does not increase the refcount when
it assigns the pointer.
Fix this issue by increasing the refcount of "struct x25_neigh" in
x25_rx_call_request.
This patch fixes frequent kernel crashes when using AF_X25 sockets.
Fixes: 4becb7ee5b3d ("net/x25: Fix x25_neigh refcnt leak when x25 disconnect") Cc: Martin Schiller <ms@dev.tdt.de> Signed-off-by: Xie He <xie.he.0141@gmail.com> Link: https://lore.kernel.org/r/20201112103506.5875-1-xie.he.0141@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
If tcp socket has more data than Encrypted Handshake Message then
tls_sw_recvmsg will try to decrypt next record instead of returning
full control message to userspace as mentioned in comment. The next
message - usually Application Data - gets corrupted because it uses
zero copy for decryption that's why the data is not stored in skb
for next iteration. Revert check to not decrypt next record if
current is not Application Data.
Fixes: 692d7b5d1f91 ("tls: Fix recvmsg() to be able to peek across multiple records") Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru> Link: https://lore.kernel.org/r/1605413760-21153-1-git-send-email-vfedorenko@novek.ru Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Sparse complaints 3 times about:
net/smc/smc_ib.c:203:52: warning: incorrect type in argument 1 (different address spaces)
net/smc/smc_ib.c:203:52: expected struct net_device const *dev
net/smc/smc_ib.c:203:52: got struct net_device [noderef] __rcu *const ndev
Fix that by using the existing and validated ndev variable instead of
accessing attr->ndev directly.
Fixes: 5102eca9039b ("net/smc: Use rdma_read_gid_l2_fields to L2 fields") Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
During rmnet unregistration, the real device rx_handler is first cleared
followed by the removal of rx_handler_data after the rcu synchronization.
Any packets in the receive path may observe that the rx_handler is NULL.
However, there is no check when dereferencing this value to use the
rmnet_port information.
This fixes following splat by adding the NULL check.
Unable to handle kernel NULL pointer dereference at virtual
address 000000000000000d
pc : rmnet_rx_handler+0x124/0x284
lr : rmnet_rx_handler+0x124/0x284
rmnet_rx_handler+0x124/0x284
__netif_receive_skb_core+0x758/0xd74
__netif_receive_skb+0x50/0x17c
process_backlog+0x15c/0x1b8
napi_poll+0x88/0x284
net_rx_action+0xbc/0x23c
__do_softirq+0x20c/0x48c
Fixes: ceed73a2cf4a ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation") Signed-off-by: Sean Tranchetti <stranche@codeaurora.org> Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Link: https://lore.kernel.org/r/1605298325-3705-1-git-send-email-subashab@codeaurora.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Slave function read the following capabilities from the wrong offset:
1. log_mc_entry_sz
2. fs_log_entry_sz
3. log_mc_hash_sz
Fix that by adjusting these capabilities offset to match firmware
layout.
Due to the wrong offset read, the following issues might occur:
1+2. Negative value reported at max_mcast_qp_attach.
3. Driver to init FW with multicast hash size of zero.
Fixes: a40ded604365 ("net/mlx4_core: Add masking for a few queries on HCA caps") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Link: https://lore.kernel.org/r/20201118081922.553-1-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
A user reports (slightly shortened from the original message):
libphy: lantiq,xrx200-mdio: probed
mdio_bus 1e108000.switch-mii: MDIO device at address 17 is missing.
gswip 1e108000.switch lan: no phy at 2
gswip 1e108000.switch lan: failed to connect to port 2: -19
lantiq,xrx200-net 1e10b308.eth eth0: error -19 setting up slave phy
This is a single-port board using the internal Fast Ethernet PHY. The
user reports that switching to PHY scanning instead of configuring the
PHY within device-tree works around this issue.
The documentation for the standalone variant of the PHY11G (which is
probably very similar to what is used inside the xRX200 SoCs but having
the firmware burnt onto that standalone chip in the factory) states that
the PHY needs 300ms to be ready for MDIO communication after releasing
the reset.
Add a 300ms delay after initializing all GPHYs to ensure that the GPHY
firmware had enough time to initialize and to appear on the MDIO bus.
Unfortunately there is no (known) documentation on what the minimum time
to wait after releasing the reset on an internal PHY so play safe and
take the one for the external variant. Only wait after the last GPHY
firmware is loaded to not slow down the initialization too much (
xRX200 has two GPHYs but newer SoCs have at least three GPHYs).
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20201115165757.552641-1-martin.blumenstingl@googlemail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Static checking revealed that a previous fix to
netlbl_unlabel_staticlist() leaves a stack variable uninitialized,
this patches fixes that.
Fixes: 866358ec331f ("netlabel: fix our progress tracking in netlbl_unlabel_staticlist()") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Reviewed-by: James Morris <jamorris@linux.microsoft.com> Link: https://lore.kernel.org/r/160530304068.15651.18355773009751195447.stgit@sifl Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The current NetLabel code doesn't correctly keep track of the netlink
dump state in some cases, in particular when multiple interfaces with
large configurations are loaded. The problem manifests itself by not
reporting the full configuration to userspace, even though it is
loaded and active in the kernel. This patch fixes this by ensuring
that the dump state is properly reset when necessary inside the
netlbl_unlabel_staticlist() function.
Fixes: 8cc44579d1bd ("NetLabel: Introduce static network labels for unlabeled connections") Signed-off-by: Paul Moore <paul@paul-moore.com> Link: https://lore.kernel.org/r/160484450633.3752.16512718263560813473.stgit@sifl Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
DSA network devices rely on having their DSA management interface up and
running otherwise their ndo_open() will return -ENETDOWN. Without doing
this it would not be possible to use DSA devices as netconsole when
configured on the command line. These devices also do not utilize the
upper/lower linking so the check about the netpoll device having upper
is not going to be a problem.
The solution adopted here is identical to the one done for
net/ipv4/ipconfig.c with 728c02089a0e ("net: ipv4: handle DSA enabled
master network devices"), with the network namespace scope being
restricted to that of the process configuring netpoll.
Fixes: 04ff53f96a93 ("net: dsa: Add netconsole support") Tested-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20201117035236.22658-1-f.fainelli@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 83a8471ba255 ("net: ethernet: ti: cpsw: refactor probe to group common hw initialization") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Link: https://lore.kernel.org/r/1605250173-18438-1-git-send-email-zhangchangzhong@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
As soon as you add the second port to a VLAN, all other port
membership configuration is overwritten with zeroes. The HW interprets
this as all ports being "unmodified members" of the VLAN.
In the simple case when all ports belong to the same VLAN, switching
will still work. But using multiple VLANs or trying to set multiple
ports as tagged members will not work.
On the 6352, doing a VTU GetNext op, followed by an STU GetNext op
will leave you with both the member- and state- data in the VTU/STU
data registers. But on the 6097 (which uses the same implementation),
the STU GetNext will override the information gathered from the VTU
GetNext.
Separate the two stages, parsing the result of the VTU GetNext before
doing the STU GetNext.
We opt to update the existing implementation for all applicable chips,
as opposed to creating a separate callback for 6097, because although
the previous implementation did work for (at least) 6352, the
datasheet does not mention the masking behavior.
Fixes: ef6fcea37f01 ("net: dsa: mv88e6xxx: get STU entry on VTU GetNext") Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Link: https://lore.kernel.org/r/20201112114335.27371-1-tobias@waldekranz.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
In br_forward.c and br_input.c fields dev->stats.tx_dropped and
dev->stats.multicast are populated, but they are ignored in
ndo_get_stats64.
Fixes: 28172739f0a2 ("net: fix 64 bit counters on 32 bit arches") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Link: https://lore.kernel.org/r/58ea9963-77ad-a7cf-8dfd-fc95ab95f606@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 39a6f4bce6b4 ("b44: replace the ssb_dma API with the generic DMA API") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/1605582131-36735-1-git-send-email-zhangchangzhong@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The driver sends Ethernet Management Datagram (EMAD) packets to the
device for configuration purposes and waits for up to 200ms for a reply.
A request is retried up to 5 times.
When the system is under heavy load, replies are not always processed in
time and EMAD transactions fail.
Make the process more robust to such delays by using exponential
backoff. First wait for up to 200ms, then retransmit and wait for up to
400ms and so on.
Fixes: caf7297e7ab5 ("mlxsw: core: Introduce support for asynchronous EMAD register access") Reported-by: Denis Yulevich <denisyu@nvidia.com> Tested-by: Denis Yulevich <denisyu@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
projects / mirror_ubuntu-focal-kernel.git / log