Ben Hutchings [Thu, 17 Jan 2019 00:25:58 +0000 (00:25 +0000)]
media: em28xx: Fix misplaced reset of dev->v4l::field_count
BugLink: https://bugs.launchpad.net/bugs/1837477
The backport of commit afeaade90db4 "media: em28xx: make
v4l2-compliance happier by starting sequence on zero" added a
reset on em28xx_v4l2::field_count to em28xx_enable_analog_tuner()
but it should be done in em28xx_start_analog_streaming().
The Clock Data Recovery (CDR) circuit allows to automatically adjust
the RX sampling-point/phase for high frequency cards (SDR104, HS200...).
CDR is automatically enabled during DLL configuration.
However, according to the APQ8016 reference manual, this function
must be disabled during TX and tuning phase in order to prevent any
interferences during tuning challenges and unexpected phase alteration
during TX transfers.
This patch enables/disables CDR according to the current transfer mode.
This fixes sporadic write transfer issues observed with some SDR104 and
HS200 cards.
Inspired by sdhci-msm downstream patch:
https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/432516/
Reported-by: Leonid Segal <leonid.s@variscite.com> Reported-by: Manabu Igusa <migusa@arrowjapan.com> Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Georgi Djakov <georgi.djakov@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[georgi: backport to v4.14] Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Muyu Yu provided a POC where user root with CAP_NET_ADMIN can create a CAN
frame modification rule that makes the data length code a higher value than
the available CAN frame data size. In combination with a configured checksum
calculation where the result is stored relatively to the end of the data
(e.g. cgw_csum_xor_rel) the tail of the skb (e.g. frag_list pointer in
skb_shared_info) can be rewritten which finally can cause a system crash.
Michael Kubecek suggested to drop frames that have a DLC exceeding the
available space after the modification process and provided a patch that can
handle CAN FD frames too. Within this patch we also limit the length for the
checksum calculations to the maximum of Classic CAN data length (8).
CAN frames that are dropped by these additional checks are counted with the
CGW_DELETED counter which indicates misconfigurations in can-gw rules.
This fixes CVE-2019-3701.
Reported-by: Muyu Yu <ieatmuttonchuan@gmail.com> Reported-by: Marcus Meissner <meissner@suse.de> Suggested-by: Michal Kubecek <mkubecek@suse.cz> Tested-by: Muyu Yu <ieatmuttonchuan@gmail.com> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Cc: linux-stable <stable@vger.kernel.org> # >= v3.2 Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
ldsem_down_read() will sleep if there is pending writer in the queue.
If the writer times out, readers in the queue should be woken up,
otherwise they may miss a chance to acquire the semaphore until the last
active reader will do ldsem_up_read().
There was a couple of reports where there was one active reader and
other readers soft locked up:
Showing all locks held in the system:
2 locks held by khungtaskd/17:
#0: (rcu_read_lock){......}, at: watchdog+0x124/0x6d1
#1: (tasklist_lock){.+.+..}, at: debug_show_all_locks+0x72/0x2d3
2 locks held by askfirst/123:
#0: (&tty->ldisc_sem){.+.+.+}, at: ldsem_down_read+0x46/0x58
#1: (&ldata->atomic_read_lock){+.+...}, at: n_tty_read+0x115/0xbe4
Prevent readers wait for active readers to release ldisc semaphore.
When initializing the security xattrs, we are holding a transaction handle
therefore we need to use a GFP_NOFS context in order to avoid a deadlock
with reclaim in case it's triggered.
Fixes: 39a27ec1004e8 ("btrfs: use GFP_KERNEL for xattr and acl allocations") Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The available allocation bits members from struct btrfs_fs_info are
protected by a sequence lock, and when starting balance we access them
incorrectly in two different ways:
1) In the read sequence lock loop at btrfs_balance() we use the values we
read from fs_info->avail_*_alloc_bits and we can immediately do actions
that have side effects and can not be undone (printing a message and
jumping to a label). This is wrong because a retry might be needed, so
our actions must not have side effects and must be repeatable as long
as read_seqretry() returns a non-zero value. In other words, we were
essentially ignoring the sequence lock;
2) Right below the read sequence lock loop, we were reading the values
from avail_metadata_alloc_bits and avail_data_alloc_bits without any
protection from concurrent writers, that is, reading them outside of
the read sequence lock critical section.
So fix this by making sure we only read the available allocation bits
while in a read sequence lock critical section and that what we do in the
critical section is repeatable (has nothing that can not be undone) so
that any eventual retry that is needed is handled properly.
Fixes: de98ced9e743 ("Btrfs: use seqlock to protect fs_info->avail_{data, metadata, system}_alloc_bits") Fixes: 14506127979a ("btrfs: fix a bogus warning when converting only data or metadata") Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The check for special (reserved) inode number checks in __ext4_iget()
was broken by commit 8a363970d1dc: ("ext4: avoid declaring fs
inconsistent due to invalid file handles"). This was caused by a
botched reversal of the sense of the flag now known as
EXT4_IGET_SPECIAL (when it was previously named EXT4_IGET_NORMAL).
Fix the logic appropriately.
drm_dp_mst_topology_mgr_resume() returns whether or not it managed to
find the topology in question after a suspend resume cycle, and the
driver is supposed to check this value and disable MST accordingly if
it's gone-in addition to sending a hotplug in order to notify userspace
that something changed during suspend.
Currently, amdgpu just makes the mistake of ignoring the return code
from drm_dp_mst_topology_mgr_resume() which means that if a topology was
removed in suspend, amdgpu never notices and assumes it's still
connected which leads to all sorts of problems.
So, fix this by actually checking the rc from
drm_dp_mst_topology_mgr_resume(). Also, reformat the rest of the
function while we're at it to fix the over-indenting.
Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Cc: Jerry Zuo <Jerry.Zuo@amd.com> Cc: <stable@vger.kernel.org> # v4.15+ Link: https://patchwork.freedesktop.org/patch/msgid/20190108211133.32564-2-lyude@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The below referenced commit adds a test for integer overflow, but in
doing so prevents the unmap ioctl from ever including the last page of
the address space. Subtract one to compare to the last address of the
unmap to avoid the overflow and wrap-around.
Fixes: 71a7d3d78e3c ("vfio/type1: silence integer overflow warning") Link: https://bugzilla.redhat.com/show_bug.cgi?id=1662291 Cc: stable@vger.kernel.org # v4.15+ Reported-by: Pei Zhang <pezhang@redhat.com> Debugged-by: Peter Xu <peterx@redhat.com> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Peter Xu <peterx@redhat.com> Tested-by: Peter Xu <peterx@redhat.com> Reviewed-by: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When modifying the free space tree we can end up COWing one of its extent
buffers which in turn might result in allocating a new chunk, which in
turn can result in flushing (finish creation) of pending block groups. If
that happens we can deadlock because creating a pending block group needs
to update the free space tree, and if any of the updates tries to modify
the same extent buffer that we are COWing, we end up in a deadlock since
we try to write lock twice the same extent buffer.
So fix this by skipping pending block group creation if we are COWing an
extent buffer from the free space tree. This is a case missed by commit 5ce555578e091 ("Btrfs: fix deadlock when writing out free space caches").
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202173 Fixes: 5ce555578e091 ("Btrfs: fix deadlock when writing out free space caches") CC: stable@vger.kernel.org # 4.18+ Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Which results in running two VCPUs in the same VM with different VMIDs
and (even worse) other VCPUs from other VMs could now allocate clashing
VMID 254 from the new generation as long as VCPU 0 is not exiting.
Attempt to solve this by making sure vttbr is updated before another CPU
can observe the updated VMID generation.
Cc: stable@vger.kernel.org Fixes: f0cf47d939d0 "KVM: arm/arm64: Close VMID generation race" Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Christoffer Dall <christoffer.dall@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We already using mapping_set_error() in fs/ext4/page_io.c, so all we
need to do is to use file_check_and_advance_wb_err() when handling
fsync() requests in ext4_sync_file().
The xfstests generic/475 test switches the underlying device with
dm-error while running a stress test. This results in a large number
of file system errors, and since we can't lock the buffer head when
marking the superblock dirty in the ext4_grp_locked_error() case, it's
possible the superblock to be !buffer_uptodate() without
buffer_write_io_error() being true.
We need to set buffer_uptodate() before we call mark_buffer_dirty() or
this will trigger a WARN_ON. It's safe to do this since the
superblock must have been properly read into memory or the mount would
have been successful. So if buffer_uptodate() is not set, we can
safely assume that this happened due to a failed attempt to write the
superblock.
The ext4_inline_data_fiemap() function calls fiemap_fill_next_extent()
while still holding the xattr semaphore. This is not necessary and it
triggers a circular lockdep warning. This is because
fiemap_fill_next_extent() could trigger a page fault when it writes
into page which triggers a page fault. If that page is mmaped from
the inline file in question, this could very well result in a
deadlock.
This problem can be reproduced using generic/519 with a file system
configuration which has the inline_data feature enabled.
There are enough credits reserved for most dioread_nolock writes;
however, if the extent tree is sufficiently deep, and/or quota is
enabled, the code was not allowing for all eventualities when
reserving journal credits for the unwritten extent conversion.
This problem can be seen using xfstests ext4/034:
WARNING: CPU: 1 PID: 257 at fs/ext4/ext4_jbd2.c:271 __ext4_handle_dirty_metadata+0x10c/0x180
Workqueue: ext4-rsv-conversion ext4_end_io_rsv_work
RIP: 0010:__ext4_handle_dirty_metadata+0x10c/0x180
...
EXT4-fs: ext4_free_blocks:4938: aborting transaction: error 28 in __ext4_handle_dirty_metadata
EXT4: jbd2_journal_dirty_metadata failed: handle type 11 started at line 4921, credits 4/0, errcode -28
EXT4-fs error (device dm-1) in ext4_free_blocks:4950: error 28
There is a window between when RBD_DEV_FLAG_REMOVING is set and when
the device is removed from rbd_dev_list. During this window, we set
"already" and return 0.
Returning 0 from write(2) can confuse userspace tools because
0 indicates that nothing was written. In particular, "rbd unmap"
will retry the write multiple times a second:
SDL 1.2 sets all fields related to the pixel format to zero in some
cases[1]. Prior to commit db05c48197759 ("drm: fb-helper: Reject all
pixel format changing requests"), there was an unintentional workaround
for this that existed for more than a decade. First in device-specific DRM
drivers, then here in drm_fb_helper.c.
Previous code containing this workaround just ignores pixel format fields
from userspace code. Not a good thing either, as this way, driver may
silently use pixel format different from what client actually requested,
and this in turn will lead to displaying garbage on the screen. I think
that returning EINVAL to userspace in this particular case is the right
option, so I decided to left code from problematic commit untouched
instead of just reverting it entirely.
Here is the steps required to reproduce this problem exactly:
1) Compile fceux[2] with SDL 1.2.15 and without GTK or OpenGL
support. SDL should be compiled with fbdev support (which is
on by default).
2) Create /etc/fb.modes with following contents (values seems
not used, and just required to trigger problematic code in
SDL):
If adapter->retries is set to a minus value from user space via ioctl,
it will make __i2c_transfer and __i2c_smbus_xfer skip the calling to
adapter->algo->master_xfer and adapter->algo->smbus_xfer that is
registered by the underlying bus drivers, and return value 0 to all the
callers. The bus driver will never be accessed anymore by all users,
besides, the users may still get successful return value without any
error or information log print out.
If adapter->timeout is set to minus value from user space via ioctl,
it will make the retrying loop in __i2c_transfer and __i2c_smbus_xfer
always break after the the first try, due to the time_after always
returns true.
Signed-off-by: Yi Zeng <yizeng@asrmicro.com>
[wsa: minor grammar updates to commit message] Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The current-source used for the battery temp-sensor (TS) is shared with the
GPADC. For proper fuel-gauge and charger operation the TS current-source
needs to be permanently on. But to read the GPADC we need to temporary
switch the TS current-source to ondemand, so that the GPADC can use it,
otherwise we will always read an all 0 value.
The switching from on to on-ondemand is not necessary when the TS
current-source is off (this happens on devices which do not have a TS).
Prior to this commit there were 2 issues with our handling of the TS
current-source switching:
1) We were writing hardcoded values to the ADC TS pin-ctrl register,
overwriting various other unrelated bits. Specifically we were overwriting
the current-source setting for the TS and GPIO0 pins, forcing it to 80ųA
independent of its original setting. On a Chuwi Vi10 tablet this was
causing us to get a too high adc value (due to a too high current-source)
resulting in acpi_lpat_raw_to_temp() returning -ENOENT, resulting in:
ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion]
ACPI Error: Method parse/execution failed \_SB.SXP1._TMP, AE_ERROR
This commit fixes this by using regmap_update_bits to change only the
relevant bits.
2) At the end of intel_xpower_pmic_get_raw_temp() we were unconditionally
enabling the TS current-source even on devices where the TS-pin is not used
and the current-source thus was off on entry of the function.
This commit fixes this by checking if the TS current-source is off when
entering intel_xpower_pmic_get_raw_temp() and if so it is left as is.
Fixes: 58eefe2f3f53 (ACPI / PMIC: xpower: Do pinswitch ... reading GPADC) Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: 4.14+ <stable@vger.kernel.org> # 4.14+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
He adds
"task1 is waiting for the PageWriteback bit of the page that task2 has
collected in mpd->io_submit->io_bio, and tasks2 is waiting for the
LOCKED bit the page which tasks1 has locked"
More precisely task1 is handling a page fault and it has a page locked
while it charges a new page table to a memcg. That in turn hits a
memory limit reclaim and the memcg reclaim for legacy controller is
waiting on the writeback but that is never going to finish because the
writeback itself is waiting for the page locked in the #PF path. So
this is essentially ABBA deadlock:
This accumulating of more pages to flush is used by several filesystems
to generate a more optimal IO patterns.
Waiting for the writeback in legacy memcg controller is a workaround for
pre-mature OOM killer invocations because there is no dirty IO
throttling available for the controller. There is no easy way around
that unfortunately. Therefore fix this specific issue by pre-allocating
the page table outside of the page lock. We have that handy
infrastructure for that already so simply reuse the fault-around pattern
which already does this.
There are probably other hidden __GFP_ACCOUNT | GFP_KERNEL allocations
from under a fs page locked but they should be really rare. I am not
aware of a better solution unfortunately.
[akpm@linux-foundation.org: fix mm/memory.c:__do_fault()]
[akpm@linux-foundation.org: coding-style fixes]
[mhocko@kernel.org: enhance comment, per Johannes] Link: http://lkml.kernel.org/r/20181214084948.GA5624@dhcp22.suse.cz Link: http://lkml.kernel.org/r/20181213092221.27270-1-mhocko@kernel.org Fixes: c3b94f44fcb0 ("memcg: further prevent OOM with too many dirty pages") Signed-off-by: Michal Hocko <mhocko@suse.com> Reported-by: Liu Bo <bo.liu@linux.alibaba.com> Debugged-by: Liu Bo <bo.liu@linux.alibaba.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Reviewed-by: Liu Bo <bo.liu@linux.alibaba.com> Cc: Jan Kara <jack@suse.cz> Cc: Dave Chinner <david@fromorbit.com> Cc: Theodore Ts'o <tytso@mit.edu> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: Shakeel Butt <shakeelb@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
LTP proc01 testcase has been observed to rarely trigger crashes
on arm64:
page_mapped+0x78/0xb4
stable_page_flags+0x27c/0x338
kpageflags_read+0xfc/0x164
proc_reg_read+0x7c/0xb8
__vfs_read+0x58/0x178
vfs_read+0x90/0x14c
SyS_read+0x60/0xc0
The issue is that page_mapped() assumes that if compound page is not
huge, then it must be THP. But if this is 'normal' compound page
(COMPOUND_PAGE_DTOR), then following loop can keep running (for
HPAGE_PMD_NR iterations) until it tries to read from memory that isn't
mapped and triggers a panic:
for (i = 0; i < hpage_nr_pages(page); i++) {
if (atomic_read(&page[i]._mapcount) >= 0)
return true;
}
I could replicate this on x86 (v4.20-rc4-98-g60b548237fed) only
with a custom kernel module [1] which:
- allocates compound page (PAGEC) of order 1
- allocates 2 normal pages (COPY), which are initialized to 0xff (to
satisfy _mapcount >= 0)
- 2 PAGEC page structs are copied to address of first COPY page
- second page of COPY is marked as not present
- call to page_mapped(COPY) now triggers fault on access to 2nd COPY
page at offset 0x30 (_mapcount)
Callers of __alloc_alien() check for NULL. We must do the same check in
__alloc_alien_cache to avoid NULL pointer dereferences on allocation
failures.
Link: http://lkml.kernel.org/r/010001680f42f192-82b4e12e-1565-4ee0-ae1f-1e98974906aa-000000@email.amazonses.com Fixes: 49dfc304ba241 ("slab: use the lock on alien_cache, instead of the lock on array_cache") Fixes: c8522a3a5832b ("Slab: introduce alloc_alien") Signed-off-by: Christoph Lameter <cl@linux.com> Reported-by: syzbot+d6ed4ec679652b4fd4e4@syzkaller.appspotmail.com Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
To match the Corsair Strafe RGB, the Corsair K70 RGB also requires
USB_QUIRK_DELAY_CTRL_MSG to completely resolve boot connection issues
discussed here: https://github.com/ckb-next/ckb-next/issues/42.
Otherwise roughly 1 in 10 boots the keyboard will fail to be detected.
Patch that applied delay control quirk for Corsair Strafe RGB: cb88a0588717 ("usb: quirks: add control message delay for 1b1c:1b20")
Previous K70 RGB patch to add delay-init quirk: 7a1646d92257 ("Add delay-init quirk for Corsair K70 RGB keyboards")
Signed-off-by: Jack Stocker <jackstocker.93@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The SMI SM3350 USB-UFS bridge controller cannot handle long sense request
correctly and will make the chip refuse to do read/write when requested
long sense.
Currently the code will set US_FL_SANE_SENSE flag unconditionally if
device claims SPC3+, however we should allow US_FL_BAD_SENSE flag to
prevent this behavior, because SMI SM3350 UFS-USB bridge controller,
which claims SPC4, will show strange behavior with 96-byte sense
(put the chip into a wrong state that cannot read/write anything).
Check the presence of US_FL_BAD_SENSE when assuming US_FL_SANE_SENSE on
SPC4+ devices.
Currently we hide EINTR code returned from sock_sendmsg()
and return 0 instead. This makes a caller think that we
successfully completed the network operation which is not
true. Fix this by properly returning EINTR to callers.
Cc: <stable@vger.kernel.org> Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently for MTU requests we allocate maximum possible credits
in advance and then adjust them according to the request size.
While we were adjusting the number of credits belonging to the
server, we were skipping adjustment of credits belonging to the
request. This patch fixes it by setting request credits to
CreditCharge field value of SMB2 packet header.
Also ask 1 credit more for async read and write operations to
increase parallelism and match the behavior of other operations.
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
'encoder' is dereferenced before it is null sanity checked, hence we
potentially have a null pointer dereference bug. Instead, initialise
drm_drv from encoder->dev->dev_private after we are sure 'encoder' is
not null.
Fixes: 5182c1a556d7f ("drm/rockchip: add an common abstracted PSR driver") Cc: stable@vger.kernel.org Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://patchwork.freedesktop.org/patch/msgid/20181013105654.11827-1-enric.balletbo@collabora.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We need to actually make sure we check this on resume since otherwise we
won't know whether or not the topology is still there once we've
resumed, which will cause us to still think the topology is connected
even after it's been removed if the removal happens mid-suspend.
Signed-off-by: Lyude Paul <lyude@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For DDRC PMU, each PMU counter is fixed-purpose. There is a mismatch
between perf list and driver definition on rw_chg event.
# perf list | grep chg
hisi_sccl1_ddrc0/rnk_chg/ [Kernel PMU event]
hisi_sccl1_ddrc0/rw_chg/ [Kernel PMU event]
But the register offset of rw_chg event is not defined in the driver,
meanwhile bnk_chg register offset is mis-defined, let's fixup it.
Fixes: 904dcf03f086 ("perf: hisi: Add support for HiSilicon SoC DDRC PMU driver") Cc: stable@vger.kernel.org Cc: John Garry <john.garry@huawei.com> Cc: Will Deacon <will.deacon@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Reported-by: Weijian Huang <huangweijian4@hisilicon.com> Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This patch solves the register readback issue with the bit shift. When the
dac resolution was lower than the register size (ex. 12 bits out of 16
bits) the readback value was not shifted with the difference in bits and
the value was higher. Also a mask is applied on the read value in order to
get the value relative to the actual bit size.
Fixes: 0357e488b8 ("iio:dac:ad5686: Refactor the driver") Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
a9c8088c7988 ("i2c: i801: Don't restore config registers on runtime PM")
nullified the runtime PM suspend/resume callback pointers while keeping the
runtime PM enabled.
This caused the SMBus PCI device to stay in D0 with
/sys/devices/.../power/runtime_status showing "error" when the runtime PM
framework attempted to autosuspend the device. This is due to PCI bus
runtime PM, which checks for driver runtime PM callbacks and returns
-ENOSYS if they are not set.
Since i2c-i801.c doesn't need to do anything device-specific for runtime
PM, Jean Delvare proposed this be fixed in the PCI core rather than adding
dummy runtime PM callback functions in the PCI drivers.
Change pci_pm_runtime_suspend()/pci_pm_runtime_resume() so they allow
changing the PCI device power state during runtime PM transitions even if
the driver supplies no runtime PM callbacks.
This fixes the runtime PM regression on i2c-i801.c.
It is not obvious why the code previously required the runtime PM
callbacks. The test has been there since the code was introduced by 6cbf82148ff2 ("PCI PM: Run-time callbacks for PCI bus type").
On the other hand, a similar change was done to generic runtime PM
callbacks in 05aa55dddb9e ("PM / Runtime: Lenient generic runtime pm
callbacks").
Fixes: a9c8088c7988 ("i2c: i801: Don't restore config registers on runtime PM") Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: stable@vger.kernel.org # v4.18+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
rwb_enabled() can't be changed when there is any inflight IO.
wbt_disable_default() may set rwb->wb_normal as zero, however the
blk_stat timer may still be pending, and the timer function will update
wrb->wb_normal again.
This patch introduces blk_stat_deactivate() and applies it in
wbt_disable_default(), then the following IO hang triggered when running
parted & switching io scheduler can be fixed:
The failure path removes the allocated PIDs from the wrong namespace.
This could lead to us inadvertently reusing PIDs in the leaf namespace
and leaking PIDs in parent namespaces.
When reading buffer descriptors on RX or on TX completion, an
RX_USED/TX_USED bit is checked first to ensure that the descriptors have
been populated, i.e. the ownership has been transferred. However, there
are no memory barriers to ensure that the data protected by the
RX_USED/TX_USED bit is up-to-date with respect to that bit.
Specifically:
- TX timestamp descriptors may be loaded before ctrl is loaded for the
TX_USED check, which is racy as the descriptors may be updated between
the loads, causing old timestamp descriptor data to be used.
- RX ctrl may be loaded before addr is loaded for the RX_USED check,
which is racy as a new frame may be written between the loads, causing
old ctrl descriptor data to be used.
This issue exists for both macb_rx() and gem_rx() variants.
Fix the races by adding DMA read memory barriers on those paths and
reordering the reads in macb_rx().
I have not observed any actual problems in practice caused by these
being missing, though.
Tested on a ZynqMP based system.
Fixes: 89e5785fc8a6 ("[PATCH] Atmel MACB ethernet driver") Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When the VF driver does a reset, it (at least the Linux one) writes to
the VFCTRL register to issue a reset and then immediately sends a reset
message using the mailbox API. This is racy because when the PF driver
detects that the VFCTRL register reset pin has been asserted, it clears
the mailbox memory. Depending on ordering, the reset message sent by
the VF could be cleared by the PF driver. It then responds to the
cleared message with a NACK which causes the VF driver to malfunction.
Fix this by deferring clearing the mailbox memory until the reset
message is received.
Fixes: 939b701ad633 ("ixgbe: fix driver behaviour after issuing VFLR") Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
ibmvnic_reset can create and schedule a reset work item from
an IRQ context, so do not use a mutex, which can sleep. Convert
the reset work item mutex to a spin lock. Locking debugger generated
the trace output below.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since commit d7c5f6863550 ("ARM: dts: sun8i: a83t: bananapi-m3: Add
AXP813 regulator nodes") my BPIM3 no longer works at gigabit speed.
With the default setting, dldo3 is regulated at 2.9v which seems
sufficient for the PHY but the aforementioned commit drops it to 2.5V
which is insufficient. Note that this behaviour is random for all BPIM3.
Some work with 2.5V, but some don't.
Finnaly, someone from Bananapi confirmed that this regulator must be set
to 3.3V.
Commit 7ed1c1901fe5 (tools: fix cross-compile var clobbering) removed
setting of LD to $(CROSS_COMPILE)gcc. This broke build of acpica
(acpidump) in power/acpi:
ld: unrecognized option '-D_LINUX'
The tools pass CFLAGS to the linker (incl. -D_LINUX), so revert this
particular change and let LD be $(CC) again. Note that the old behaviour
was a bit different, it used $(CROSS_COMPILE)gcc which was eliminated by
the commit 7ed1c1901fe5. We use $(CC) for that reason.
Fixes: 7ed1c1901fe5 (tools: fix cross-compile var clobbering) Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: 4.16+ <stable@vger.kernel.org> # 4.16+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Cc: Martin Kelly <martin@martingkelly.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
After some investigation I figured out that recently added cleanup code
tries to call VLAN filtering de-initialization function which exist only
for newer hardware. Corresponding function pointer is not
set (== 0) for older hardware, namely these chips:
Broadcom Inc. and subsidiaries NetXtreme II BCM57711E 10-Gigabit PCIe [14e4:1650]
Function bnx2x_init_vlan_mac_fp_objs() from
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h decides whether to
initialize relevant pointers in bnx2x_sp_objs.vlan_obj or not.
This regression was introduced after v4.20-rc7, and still exists in v4.20
release.
Fixes: 04f05230c5c13 ("bnx2x: Remove configured vlans as part of unload sequence.") Signed-off-by: Ivan Mironov <mironov.ivan@gmail.com> Signed-off-by: Ivan Mironov <mironov.ivan@gmail.com> Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When vc4_plane_state is duplicated ->is_yuv is left assigned to its
previous value, and we never set it back to false when switching to
a non-YUV format.
Fix that by setting ->is_yuv to false in the 'num_planes == 1' branch
of the vc4_plane_setup_clipping_and_scaling() function.
Fixes: fc04023fafecf ("drm/vc4: Add support for YUV planes.") Cc: <stable@vger.kernel.org> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Reviewed-by: Eric Anholt <eric@anholt.net> Link: https://patchwork.freedesktop.org/patch/msgid/20181009132446.21960-1-boris.brezillon@bootlin.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
CC lib/test_debug_virtual.o
lib/test_debug_virtual.c: In function 'test_debug_virtual_init':
lib/test_debug_virtual.c:26:7: error: implicit declaration of function 'virt_to_phys' [-Werror=implicit-function-declaration]
pa = virt_to_phys(va);
^
Fixes: e4dace361552 ("lib: add test module for CONFIG_DEBUG_VIRTUAL") CC: stable@vger.kernel.org Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The 'nr_pages' attribute of the 'msc' subdevices parses a comma-separated
list of window sizes, passed from userspace. However, there is a bug in
the string parsing logic wherein it doesn't exclude the comma character
from the range of characters as it consumes them. This leads to an
out-of-bounds access given a sufficiently long list. For example:
> # echo 8,8,8,8 > /sys/bus/intel_th/devices/0-msc0/nr_pages
> ==================================================================
> BUG: KASAN: slab-out-of-bounds in memchr+0x1e/0x40
> Read of size 1 at addr ffff8803ffcebcd1 by task sh/825
>
> CPU: 3 PID: 825 Comm: npktest.sh Tainted: G W 4.20.0-rc1+
> Call Trace:
> dump_stack+0x7c/0xc0
> print_address_description+0x6c/0x23c
> ? memchr+0x1e/0x40
> kasan_report.cold.5+0x241/0x308
> memchr+0x1e/0x40
> nr_pages_store+0x203/0xd00 [intel_th_msu]
Fix this by accounting for the comma character.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Fixes: ba82664c134ef ("intel_th: Add Memory Storage Unit driver") Cc: stable@vger.kernel.org # v4.4+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Updating mseq makes client think importer mds has accepted all prior
cap messages and importer mds knows what caps client wants. Actually
some cap messages may have been dropped because of mseq mismatch.
If mseq is left untouched, importing cap's mds_wanted later will get
reset by cap import message.
Zhipeng Xie, Xie XiuQi and Sargun Dhillon reported lockups in the
scheduler under high loads, starting at around the v4.18 time frame,
and Zhipeng Xie tracked it down to bugs in the rq->leaf_cfs_rq_list
manipulation.
Do a (manual) revert of:
a9e7f6544b9c ("sched/fair: Fix O(nr_cgroups) in load balance path")
It turns out that the list_del_leaf_cfs_rq() introduced by this commit
is a surprising property that was not considered in followup commits
such as:
9c2791f936ef ("sched/fair: Fix hierarchical order in rq->leaf_cfs_rq_list")
As Vincent Guittot explains:
"I think that there is a bigger problem with commit a9e7f6544b9c and
cfs_rq throttling:
Let take the example of the following topology TG2 --> TG1 --> root:
1) The 1st time a task is enqueued, we will add TG2 cfs_rq then TG1
cfs_rq to leaf_cfs_rq_list and we are sure to do the whole branch in
one path because it has never been used and can't be throttled so
tmp_alone_branch will point to leaf_cfs_rq_list at the end.
2) Then TG1 is throttled
3) and we add TG3 as a new child of TG1.
4) The 1st enqueue of a task on TG3 will add TG3 cfs_rq just before TG1
cfs_rq and tmp_alone_branch will stay on rq->leaf_cfs_rq_list.
With commit a9e7f6544b9c, we can del a cfs_rq from rq->leaf_cfs_rq_list.
So if the load of TG1 cfs_rq becomes NULL before step 2) above, TG1
cfs_rq is removed from the list.
Then at step 4), TG3 cfs_rq is added at the beginning of rq->leaf_cfs_rq_list
but tmp_alone_branch still points to TG3 cfs_rq because its throttled
parent can't be enqueued when the lock is released.
tmp_alone_branch doesn't point to rq->leaf_cfs_rq_list whereas it should.
So if TG3 cfs_rq is removed or destroyed before tmp_alone_branch
points on another TG cfs_rq, the next TG cfs_rq that will be added,
will be linked outside rq->leaf_cfs_rq_list - which is bad.
In addition, we can break the ordering of the cfs_rq in
rq->leaf_cfs_rq_list but this ordering is used to update and
propagate the update from leaf down to root."
Instead of trying to work through all these cases and trying to reproduce
the very high loads that produced the lockup to begin with, simplify
the code temporarily by reverting a9e7f6544b9c - which change was clearly
not thought through completely.
This (hopefully) gives us a kernel that doesn't lock up so people
can continue to enjoy their holidays without worrying about regressions. ;-)
[ mingo: Wrote changelog, fixed weird spelling in code comment while at it. ]
Analyzed-by: Xie XiuQi <xiexiuqi@huawei.com> Analyzed-by: Vincent Guittot <vincent.guittot@linaro.org> Reported-by: Zhipeng Xie <xiezhipeng1@huawei.com> Reported-by: Sargun Dhillon <sargun@sargun.me> Reported-by: Xie XiuQi <xiexiuqi@huawei.com> Tested-by: Zhipeng Xie <xiezhipeng1@huawei.com> Tested-by: Sargun Dhillon <sargun@sargun.me> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: Vincent Guittot <vincent.guittot@linaro.org> Cc: <stable@vger.kernel.org> # v4.13+ Cc: Bin Li <huawei.libin@huawei.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Tejun Heo <tj@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: a9e7f6544b9c ("sched/fair: Fix O(nr_cgroups) in load balance path") Link: http://lkml.kernel.org/r/1545879866-27809-1-git-send-email-xiexiuqi@huawei.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The Intel IOMMU driver opportunistically skips a few top level page
tables from the domain paging directory while programming the IOMMU
context entry. However there is an implicit assumption in the code that
domain's adjusted guest address width (agaw) would always be greater
than IOMMU's agaw.
The IOMMU capabilities in an upcoming platform cause the domain's agaw
to be lower than IOMMU's agaw. The issue is seen when the IOMMU supports
both 4-level and 5-level paging. The domain builds a 4-level page table
based on agaw of 2. However the IOMMU's agaw is set as 3 (5-level). In
this case the code incorrectly tries to skip page page table levels.
This causes the IOMMU driver to avoid programming the context entry. The
fix handles this case and programs the context entry accordingly.
Fixes: de24e55395698 ("iommu/vt-d: Simplify domain_context_mapping_one") Cc: <stable@vger.kernel.org> Cc: Ashok Raj <ashok.raj@intel.com> Cc: Jacob Pan <jacob.jun.pan@linux.intel.com> Cc: Lu Baolu <baolu.lu@linux.intel.com> Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com> Reported-by: Ramos Falcon, Ernesto R <ernesto.r.ramos.falcon@intel.com> Tested-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com> Signed-off-by: Sohil Mehta <sohil.mehta@intel.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Error completions must still contain a valid wr_id and
qp_num such that the consumer can rely on. Correctly
fill these fields in receive error completions.
If the requested msize is too small (either from command line argument
or from the server version reply), we won't get any work done.
If it's *really* too small, nothing will work, and this got caught by
syzbot recently (on a new kmem_cache_create_usercopy() call)
Just set a minimum msize to 4k in both code paths, until someone
complains they have a use-case for a smaller msize.
We need to check in both mount option and server reply individually
because the msize for the first version request would be unchecked
with just a global check on clnt->msize.
On a signal handler return, the user could set a context with MSR[TS] bits
set, and these bits would be copied to task regs->msr.
At restore_tm_sigcontexts(), after current task regs->msr[TS] bits are set,
several __get_user() are called and then a recheckpoint is executed.
This is a problem since a page fault (in kernel space) could happen when
calling __get_user(). If it happens, the process MSR[TS] bits were
already set, but recheckpoint was not executed, and SPRs are still invalid.
The page fault can cause the current process to be de-scheduled, with
MSR[TS] active and without tm_recheckpoint() being called. More
importantly, without TEXASR[FS] bit set also.
Since TEXASR might not have the FS bit set, and when the process is
scheduled back, it will try to reclaim, which will be aborted because of
the CPU is not in the suspended state, and, then, recheckpoint. This
recheckpoint will restore thread->texasr into TEXASR SPR, which might be
zero, hitting a BUG_ON().
This patch simply delays the MSR[TS] set, so, if there is any page fault in
the __get_user() section, it does not have regs->msr[TS] set, since the TM
structures are still invalid, thus avoiding doing TM operations for
in-kernel exceptions and possible process reschedule.
With this patch, the MSR[TS] will only be set just before recheckpointing
and setting TEXASR[FS] = 1, thus avoiding an interrupt with TM registers in
invalid state.
Other than that, if CONFIG_PREEMPT is set, there might be a preemption just
after setting MSR[TS] and before tm_recheckpoint(), thus, this block must
be atomic from a preemption perspective, thus, calling
preempt_disable/enable() on this code.
It is not possible to move tm_recheckpoint to happen earlier, because it is
required to get the checkpointed registers from userspace, with
__get_user(), thus, the only way to avoid this undesired behavior is
delaying the MSR[TS] set.
The 32-bits signal handler seems to be safe this current issue, but, it
might be exposed to the preemption issue, thus, disabling preemption in
this chunk of code.
Changes from v2:
* Run the critical section with preempt_disable.
Fixes: 87b4e5393af7 ("powerpc/tm: Fix return of active 64bit signals") Cc: stable@vger.kernel.org (v3.9+) Signed-off-by: Breno Leitao <leitao@debian.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
readelf complains about the section layout of vmlinux when building
with CONFIG_RELOCATABLE=y (for KASLR):
readelf: Warning: [21]: Link field (0) should index a symtab section.
readelf: Warning: [21]: Info field (0) should index a relocatable section.
Also, it seems that our use of '-pie -shared' is contradictory, and
thus ambiguous. In general, the way KASLR is wired up at the moment
is highly tailored to how ld.bfd happens to implement (and conflate)
PIE executables and shared libraries, so given the current effort to
support other toolchains, let's fix some of these issues as well.
- Drop the -pie linker argument and just leave -shared. In ld.bfd,
the differences between them are unclear (except for the ELF type
of the produced image [0]) but lld chokes on seeing both at the
same time.
- Rename the .rela output section to .rela.dyn, as is customary for
shared libraries and PIE executables, so that it is not misidentified
by readelf as a static relocation section (producing the warnings
above).
- Pass the -z notext and -z norelro options to explicitly instruct the
linker to permit text relocations, and to omit the RELRO program
header (which requires a certain section layout that we don't adhere
to in the kernel). These are the defaults for current versions of
ld.bfd.
- Discard .eh_frame and .gnu.hash sections to avoid them from being
emitted between .head.text and .text, screwing up the section layout.
These changes only affect the ELF image, and produce the same binary
image.
[0] b9dce7f1ba01 ("arm64: kernel: force ET_DYN ELF type for ...")
Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Peter Smith <peter.smith@linaro.org> Tested-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 1212f7a16af4 ("scripts/kallsyms: filter arm64's __efistub_
symbols") updated the kallsyms code to filter out symbols with
the __efistub_ prefix explicitly, so we no longer require the
hack in our linker script to emit them as absolute symbols.
Cc: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com>
[ND: adjusted for context] Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On arm64, the EFI stub and the kernel proper are essentially the same
binary, although the EFI stub executes at a different virtual address
as the kernel. For this reason, the EFI stub is restricted in the
symbols it can link to, which is ensured by prefixing all EFI stub
symbols with __efistub_ (and emitting __efistub_ prefixed aliases for
routines that may be shared between the core kernel and the stub)
These symbols are leaking into kallsyms, polluting the namespace, so
let's filter them explicitly.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Cc: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Do the LE conversions before doing the Infiniband-related range checks.
The incorrect checks are otherwise causing a failure to load any policy
with an ibendportcon rule on BE systems. This can be reproduced by
running (on e.g. ppc64):
The cordic routine for calculating sines and cosines that was added in
commit 6f98e62a9f1b ("b43: update cordic code to match current specs")
contains an error whereby a quantity declared u32 can in fact go negative.
This problem was detected by Priit Laes who is switching b43 to use the
routine in the library functions of the kernel.
Fixes: 986504540306 ("b43: make cordic common (LP-PHY and N-PHY need it)") Reported-by: Priit Laes <plaes@plaes.org> Cc: Rafał Miłecki <zajec5@gmail.com> Cc: Stable <stable@vger.kernel.org> # 2.6.34 Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Priit Laes <plaes@plaes.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In gfs2_create_inode, after setting and releasing the acl / default_acl, the
acl / default_acl pointers are not set to NULL as they should be. In that
state, when the function reaches label fail_free_acls, gfs2_create_inode will
try to release the same acls again.
Fix that by setting the pointers to NULL after releasing the acls. Slightly
simplify the logic. Also, posix_acl_release checks for NULL already, so
there is no need to duplicate those checks here.
Fixes: e01580bf9e4d ("gfs2: use generic posix ACL infrastructure") Reported-by: Pan Bian <bianpan2016@163.com> Cc: Christoph Hellwig <hch@lst.de> Cc: stable@vger.kernel.org # v4.9+ Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In `create_composite_quirk`, the terminating condition of for loops is
`quirk->ifnum < 0`. So any composite quirks should end with `struct
snd_usb_audio_quirk` object with ifnum < 0.
for (quirk = quirk_comp->data; quirk->ifnum >= 0; ++quirk) {
.....
}
the data field of Bower's & Wilkins PX headphones usb device device quirks
do not end with {.ifnum = -1}, wihch may result in out-of-bound read.
This Patch fix the bug by adding an ending quirk object.
The parser for the processing unit reads bNrInPins field before the
bLength sanity check, which may lead to an out-of-bound access when a
malformed descriptor is given. Fix it by assignment after the bLength
check.
We cannot build these files with clang as it does not allow altivec
instructions in assembly when -msoft-float is passed.
Jinsong Ji <jji@us.ibm.com> wrote:
> We currently disable Altivec/VSX support when enabling soft-float. So
> any usage of vector builtins will break.
>
> Enable Altivec/VSX with soft-float may need quite some clean up work, so
> I guess this is currently a limitation.
>
> Removing -msoft-float will make it work (and we are lucky that no
> floating point instructions will be generated as well).
This is a workaround until the issue is resolved in clang.
Link: https://bugs.llvm.org/show_bug.cgi?id=31177 Link: https://github.com/ClangBuiltLinux/linux/issues/239 Signed-off-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[nc: Use 'ifeq ($(cc-name),clang)' instead of 'ifdef CONFIG_CC_IS_CLANG'
because that config does not exist in 4.14; the Kconfig rewrite
that added that config happened in 4.18] Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Clang needs to be told which target it is building for when cross
compiling.
Link: https://github.com/ClangBuiltLinux/linux/issues/259 Signed-off-by: Joel Stanley <joel@jms.id.au> Tested-by: Daniel Axtens <dja@axtens.net> # powerpc 64-bit BE Acked-by: Michael Ellerman <mpe@ellerman.id.au> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[nc: Use 'ifeq ($(cc-name),clang)' instead of 'ifdef CONFIG_CC_IS_CLANG'
because that config does not exist in 4.14; the Kconfig rewrite
that added that config happened in 4.18] Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Collect basic Clang options such as --target, --prefix, --gcc-toolchain,
-no-integrated-as into a single variable CLANG_FLAGS so that it can be
easily reused in other parts of Makefile.
We are still a way off the Clang's integrated assembler support for
the kernel. Hence, -no-integrated-as is mandatory to build the kernel
with Clang. If you had an ancient version of Clang that does not
recognize this option, you would not be able to compile the kernel
anyway.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Tested-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Joel Stanley [Mon, 17 Sep 2018 07:37:54 +0000 (17:07 +0930)]
ftrace: Build with CPPFLAGS to get -Qunused-arguments
BugLink: https://bugs.launchpad.net/bugs/1837477
When building to record the mcount locations the kernel uses
KBUILD_CFLAGS but not KBUILD_CPPFLAGS. This means it lacks
-Qunused-arguments when building with clang, resulting in a lot of
noisy warnings.
Signed-off-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[nc: Fix conflicts due to lack of 87a32e624037 and d503ac531a52] Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The powerpc kernel uses setjmp which causes a warning when building
with clang:
In file included from arch/powerpc/xmon/xmon.c:51:
./arch/powerpc/include/asm/setjmp.h:15:13: error: declaration of
built-in function 'setjmp' requires inclusion of the header <setjmp.h>
[-Werror,-Wbuiltin-requires-header]
extern long setjmp(long *);
^
./arch/powerpc/include/asm/setjmp.h:16:13: error: declaration of
built-in function 'longjmp' requires inclusion of the header <setjmp.h>
[-Werror,-Wbuiltin-requires-header]
extern void longjmp(long *, long);
^
This *is* the header and we're not using the built-in setjump but
rather the one in arch/powerpc/kernel/misc.S. As the compiler warning
does not make sense, it for the files where setjmp is used.
Signed-off-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
[mpe: Move subdir-ccflags in xmon/Makefile to not clobber -Werror] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[nc: Adjust context due to lack of f2910f0e6835 and 2a056f58fd33] Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
After commit d202cce8963d, an expired cache_head can be removed from the
cache_detail's hash.
However, the expired cache_head may be waiting for a reply from a
previously submitted request. Such a cache_head has an increased
refcounter and therefore it won't be freed after cache_put(freeme).
Because the cache_head was removed from the hash it cannot be found
during cache_clean() and can be leaked forever, together with stalled
cache_request and other taken resources.
In our case we noticed it because an entry in the export cache was
holding a reference on a filesystem.
Fixes d202cce8963d ("sunrpc: never return expired entries in sunrpc_cache_lookup") Cc: Pavel Tikhomirov <ptikhomirov@virtuozzo.com> Cc: stable@kernel.org # 2.6.35 Signed-off-by: Vasily Averin <vvs@virtuozzo.com> Reviewed-by: NeilBrown <neilb@suse.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
KSM pages may be mapped to the multiple VMAs that cannot be reached from
one anon_vma. So during swapin, a new copy of the page need to be
generated if a different anon_vma is needed, please refer to comments of
ksm_might_need_to_copy() for details.
During swapoff, unuse_vma() uses anon_vma (if available) to locate VMA and
virtual address mapped to the page, so not all mappings to a swapped out
KSM page could be found. So in try_to_unuse(), even if the swap count of
a swap entry isn't zero, the page needs to be deleted from swap cache, so
that, in the next round a new page could be allocated and swapin for the
other mappings of the swapped out KSM page.
But this contradicts with the THP swap support. Where the THP could be
deleted from swap cache only after the swap count of every swap entry in
the huge swap cluster backing the THP has reach 0. So try_to_unuse() is
changed in commit e07098294adf ("mm, THP, swap: support to reclaim swap
space for THP swapped out") to check that before delete a page from swap
cache, but this has broken KSM swapoff too.
Fortunately, KSM is for the normal pages only, so the original behavior
for KSM pages could be restored easily via checking PageTransCompound().
That is how this patch works.
The bug is introduced by e07098294adf ("mm, THP, swap: support to reclaim
swap space for THP swapped out"), which is merged by v4.14-rc1. So I
think we should backport the fix to from 4.14 on. But Hugh thinks it may
be rare for the KSM pages being in the swap device when swapoff, so nobody
reports the bug so far.
Link: http://lkml.kernel.org/r/20181226051522.28442-1-ying.huang@intel.com Fixes: e07098294adf ("mm, THP, swap: support to reclaim swap space for THP swapped out") Signed-off-by: "Huang, Ying" <ying.huang@intel.com> Reported-by: Hugh Dickins <hughd@google.com> Tested-by: Hugh Dickins <hughd@google.com> Acked-by: Hugh Dickins <hughd@google.com> Cc: Rik van Riel <riel@redhat.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Shaohua Li <shli@kernel.org> Cc: Daniel Jordan <daniel.m.jordan@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
At Maintainer Summit, Greg brought up a topic I proposed around
EXPORT_SYMBOL_GPL usage. The motivation was considerations for when
EXPORT_SYMBOL_GPL is warranted and the criteria for taking the exceptional
step of reclassifying an existing export. Specifically, I wanted to make
the case that although the line is fuzzy and hard to specify in abstract
terms, it is nonetheless clear that devm_memremap_pages() and HMM
(Heterogeneous Memory Management) have crossed it. The
devm_memremap_pages() facility should have been EXPORT_SYMBOL_GPL from the
beginning, and HMM as a derivative of that functionality should have
naturally picked up that designation as well.
Contrary to typical rules, the HMM infrastructure was merged upstream with
zero in-tree consumers. There was a promise at the time that those users
would be merged "soon", but it has been over a year with no drivers
arriving. While the Nouveau driver is about to belatedly make good on
that promise it is clear that HMM was targeted first and foremost at an
out-of-tree consumer.
HMM is derived from devm_memremap_pages(), a facility Christoph and I
spearheaded to support persistent memory. It combines a device lifetime
model with a dynamically created 'struct page' / memmap array for any
physical address range. It enables coordination and control of the many
code paths in the kernel built to interact with memory via 'struct page'
objects. With HMM the integration goes even deeper by allowing device
drivers to hook and manipulate page fault and page free events.
One interpretation of when EXPORT_SYMBOL is suitable is when it is
exporting stable and generic leaf functionality. The
devm_memremap_pages() facility continues to see expanding use cases,
peer-to-peer DMA being the most recent, with no clear end date when it
will stop attracting reworks and semantic changes. It is not suitable to
export devm_memremap_pages() as a stable 3rd party driver API due to the
fact that it is still changing and manipulates core behavior. Moreover,
it is not in the best interest of the long term development of the core
memory management subsystem to permit any external driver to effectively
define its own system-wide memory management policies with no
encouragement to engage with upstream.
I am also concerned that HMM was designed in a way to minimize further
engagement with the core-MM. That, with these hooks in place,
device-drivers are free to implement their own policies without much
consideration for whether and how the core-MM could grow to meet that
need. Going forward not only should HMM be EXPORT_SYMBOL_GPL, but the
core-MM should be allowed the opportunity and stimulus to change and
address these new use cases as first class functionality.
Original changelog:
hmm_devmem_add(), and hmm_devmem_add_resource() duplicated
devm_memremap_pages() and are now simple now wrappers around the core
facility to inject a dev_pagemap instance into the global pgmap_radix and
hook page-idle events. The devm_memremap_pages() interface is base
infrastructure for HMM. HMM has more and deeper ties into the kernel
memory management implementation than base ZONE_DEVICE which is itself a
EXPORT_SYMBOL_GPL facility.
Originally, the HMM page structure creation routines copied the
devm_memremap_pages() code and reused ZONE_DEVICE. A cleanup to unify the
implementations was discussed during the initial review:
http://lkml.iu.edu/hypermail/linux/kernel/1701.2/00812.html Recent work to
extend devm_memremap_pages() for the peer-to-peer-DMA facility enabled
this cleanup to move forward.
In addition to the integration with devm_memremap_pages() HMM depends on
other GPL-only symbols:
It goes further to consume / indirectly expose functionality that is not
exported to any other driver:
alloc_pages_vma
walk_page_range
HMM is derived from devm_memremap_pages(), and extends deep core-kernel
fundamentals. Similar to devm_memremap_pages(), mark its entry points
EXPORT_SYMBOL_GPL().
[logang@deltatee.com: PCI/P2PDMA: match interface changes to devm_memremap_pages()] Link: http://lkml.kernel.org/r/20181130225911.2900-1-logang@deltatee.com Link: http://lkml.kernel.org/r/154275560565.76910.15919297436557795278.stgit@dwillia2-desk3.amr.corp.intel.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Logan Gunthorpe <logang@deltatee.com> Cc: "Jérôme Glisse" <jglisse@redhat.com> Cc: Balbir Singh <bsingharora@gmail.com>, Cc: Michal Hocko <mhocko@suse.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
devm semantics arrange for resources to be torn down when
device-driver-probe fails or when device-driver-release completes.
Similar to devm_memremap_pages() there is no need to support an explicit
remove operation when the users properly adhere to devm semantics.
Note that devm_kzalloc() automatically handles allocating node-local
memory.
Link: http://lkml.kernel.org/r/154275559545.76910.9186690723515469051.stgit@dwillia2-desk3.amr.corp.intel.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Jérôme Glisse <jglisse@redhat.com> Cc: "Jérôme Glisse" <jglisse@redhat.com> Cc: Logan Gunthorpe <logang@deltatee.com> Cc: Balbir Singh <bsingharora@gmail.com> Cc: Michal Hocko <mhocko@suse.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Given the fact that devm_memremap_pages() requires a percpu_ref that is
torn down by devm_memremap_pages_release() the current support for mapping
RAM is broken.
Support for remapping "System RAM" has been broken since the beginning and
there is no existing user of this this code path, so just kill the support
and make it an explicit error.
This cleanup also simplifies a follow-on patch to fix the error path when
setting a devm release action for devm_memremap_pages_release() fails.
Link: http://lkml.kernel.org/r/154275557997.76910.14689813630968180480.stgit@dwillia2-desk3.amr.corp.intel.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: "Jérôme Glisse" <jglisse@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Logan Gunthorpe <logang@deltatee.com> Cc: Balbir Singh <bsingharora@gmail.com> Cc: Michal Hocko <mhocko@suse.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
devm_memremap_pages() is a facility that can create struct page entries
for any arbitrary range and give drivers the ability to subvert core
aspects of page management.
Specifically the facility is tightly integrated with the kernel's memory
hotplug functionality. It injects an altmap argument deep into the
architecture specific vmemmap implementation to allow allocating from
specific reserved pages, and it has Linux specific assumptions about page
structure reference counting relative to get_user_pages() and
get_user_pages_fast(). It was an oversight and a mistake that this was
not marked EXPORT_SYMBOL_GPL from the outset.
Again, devm_memremap_pagex() exposes and relies upon core kernel internal
assumptions and will continue to evolve along with 'struct page', memory
hotplug, and support for new memory types / topologies. Only an in-kernel
GPL-only driver is expected to keep up with this ongoing evolution. This
interface, and functionality derived from this interface, is not suitable
for kernel-external drivers.
Link: http://lkml.kernel.org/r/154275557457.76910.16923571232582744134.stgit@dwillia2-desk3.amr.corp.intel.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Acked-by: Michal Hocko <mhocko@suse.com> Cc: "Jérôme Glisse" <jglisse@redhat.com> Cc: Balbir Singh <bsingharora@gmail.com> Cc: Logan Gunthorpe <logang@deltatee.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We have received a bug report that an injected MCE about faulty memory
prevents memory offline to succeed on 4.4 base kernel. The underlying
reason was that the HWPoison page has an elevated reference count and the
migration keeps failing. There are two problems with that. First of all
it is dubious to migrate the poisoned page because we know that accessing
that memory is possible to fail. Secondly it doesn't make any sense to
migrate a potentially broken content and preserve the memory corruption
over to a new location.
Oscar has found out that 4.4 and the current upstream kernels behave
slightly differently with his simply testcase
===
int main(void)
{
int ret;
int i;
int fd;
char *array = malloc(4096);
char *array_locked = malloc(4096);
And that latter confuses the hotremove path because an LRU page is
attempted to be migrated and that fails due to an elevated reference
count. It is quite possible that the reuse of the HWPoisoned page is some
kind of fixed race condition but I am not really sure about that.
With the upstream kernel the failure is slightly different. The page
doesn't seem to have LRU bit set but isolate_movable_page simply fails and
do_migrate_range simply puts all the isolated pages back to LRU and
therefore no progress is made and scan_movable_pages finds same set of
pages over and over again.
Fix both cases by explicitly checking HWPoisoned pages before we even try
to get reference on the page, try to unmap it if it is still mapped. As
explained by Naoya:
: Hwpoison code never unmapped those for no big reason because
: Ksm pages never dominate memory, so we simply didn't have strong
: motivation to save the pages.
Also put WARN_ON(PageLRU) in case there is a race and we can hit LRU
HWPoison pages which shouldn't happen but I couldn't convince myself about
that. Naoya has noted the following:
: Theoretically no such gurantee, because try_to_unmap() doesn't have a
: guarantee of success and then memory_failure() returns immediately
: when hwpoison_user_mappings fails.
: Or the following code (comes after hwpoison_user_mappings block) also impli=
: es
: that the target page can still have PageLRU flag.
:
: /*
: * Torn down by someone else?
: */
: if (PageLRU(p) && !PageSwapCache(p) && p->mapping =3D=3D NULL) {
: action_result(pfn, MF_MSG_TRUNCATED_LRU, MF_IGNORED);
: res =3D -EBUSY;
: goto out;
: }
:
: So I think it's OK to keep "if (WARN_ON(PageLRU(page)))" block in
: current version of your patch.
Link: http://lkml.kernel.org/r/20181206120135.14079-1-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Oscar Salvador <osalvador@suse.com> Debugged-by: Oscar Salvador <osalvador@suse.com> Tested-by: Oscar Salvador <osalvador@suse.com> Acked-by: David Hildenbrand <david@redhat.com> Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently a number of Makefiles break when used with toolchains that
pass extra flags in CC and other cross-compile related variables (such
as --sysroot).
Thus we get this error when we use a toolchain that puts --sysroot in
the CC var:
~/src/linux/tools$ make iio
[snip]
iio_event_monitor.c:18:10: fatal error: unistd.h: No such file or directory
#include <unistd.h>
^~~~~~~~~~
This occurs because we clobber several env vars related to
cross-compiling with lines like this:
CC = $(CROSS_COMPILE)gcc
Although this will point to a valid cross-compiler, we lose any extra
flags that might exist in the CC variable, which can break toolchains
that rely on them (for example, those that use --sysroot).
Although arm-poky-linux-gnueabi-gcc is a cross-compiler, we've lost the
--sysroot and other flags that enable us to find the right libraries to
link against, so we can't find unistd.h and other libraries and headers.
Normally with the --sysroot flag we would find unistd.h in the sdk
directory in the sysroot:
The perf Makefile adds CC = $(CROSS_COMPILE)gcc if and only if CC is not
already set, and it compiles correctly with the above toolchain.
So, generalize the logic that perf uses in the common Makefile and
remove the manual CC = $(CROSS_COMPILE)gcc lines from each Makefile.
Note that this patch does not fix cross-compile for all the tools (some
have other bugs), but it does fix it for all except usb and acpi, which
still have other unrelated issues.
I tested both with and without the patch on native and cross-build and
there appear to be no regressions.
Link: http://lkml.kernel.org/r/20180107214028.23771-1-martin@martingkelly.com Signed-off-by: Martin Kelly <martin@martingkelly.com> Acked-by: Mark Brown <broonie@kernel.org> Cc: Tejun Heo <tj@kernel.org> Cc: Li Zefan <lizefan@huawei.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Pali Rohar <pali.rohar@gmail.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Robert Moore <robert.moore@intel.com> Cc: Lv Zheng <lv.zheng@intel.com> Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Valentina Manea <valentina.manea.m@gmail.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Mario Limonciello <mario.limonciello@dell.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Ignat Korchagin <ignat@cloudflare.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Certain older adapters such as the OneConnect OCe10100 may not have a valid
wqpcnt value. In this case, do not set queue->page_count to 0 in
lpfc_sli4_queue_alloc() as this will prevent the driver from initializing.
Fixes: 895427bd01 ("scsi: lpfc: NVME Initiator: Base modifications") Cc: stable@vger.kernel.org # 4.11+ Signed-off-by: Ewan D. Milne <emilne@redhat.com> Reviewed-by: Laurence Oberman <loberman@redhat.com> Tested-by: Laurence Oberman <loberman@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Suppose adapter (open) recovery is between opened QDIO queues and before
(the end of) initial posting of status read buffers (SRBs). This time
window can be seconds long due to FSF_PROT_HOST_CONNECTION_INITIALIZING
causing by design looping with exponential increase sleeps in the function
performing exchange config data during recovery
[zfcp_erp_adapter_strat_fsf_xconf()]. Recovery triggered by local link up.
Suppose an event occurs for which the FCP channel would send an unsolicited
notification to zfcp by means of a previously posted SRB. We saw it with
local cable pull (link down) in multi-initiator zoning with multiple
NPIV-enabled subchannels of the same shared FCP channel.
As soon as zfcp_erp_adapter_strategy_open_fsf() starts posting the initial
status read buffers from within the adapter's ERP thread, the channel does
send an unsolicited notification.
Since v2.6.27 commit d26ab06ede83 ("[SCSI] zfcp: receiving an unsolicted
status can lead to I/O stall"), zfcp_fsf_status_read_handler() schedules
adapter->stat_work to re-fill the just consumed SRB from a work item.
Now the ERP thread and the work item post SRBs in parallel. Both contexts
call the helper function zfcp_status_read_refill(). The tracking of
missing (to be posted / re-filled) SRBs is not thread-safe due to separate
atomic_read() and atomic_dec(), in order to depend on posting
success. Hence, both contexts can see
atomic_read(&adapter->stat_miss) == 1. One of the two contexts posts
one too many SRB. Zfcp gets QDIO_ERROR_SLSB_STATE on the output queue
(trace tag "qdireq1") leading to zfcp_erp_adapter_shutdown() in
zfcp_qdio_handler_error().
An obvious and seemingly clean fix would be to schedule stat_work from the
ERP thread and wait for it to finish. This would serialize all SRB
re-fills. However, we already have another work item wait on the ERP
thread: adapter->scan_work runs zfcp_fc_scan_ports() which calls
zfcp_fc_eval_gpn_ft(). The latter calls zfcp_erp_wait() to wait for all the
open port recoveries during zfcp auto port scan, but in fact it waits for
any pending recovery including an adapter recovery. This approach leads to
a deadlock. [see also v3.19 commit 18f87a67e6d6 ("zfcp: auto port scan
resiliency"); v2.6.37 commit d3e1088d6873
("[SCSI] zfcp: No ERP escalation on gpn_ft eval");
v2.6.28 commit fca55b6fb587
("[SCSI] zfcp: fix deadlock between wq triggered port scan and ERP")
fixing v2.6.27 commit c57a39a45a76
("[SCSI] zfcp: wait until adapter is finished with ERP during auto-port");
v2.6.27 commit cc8c282963bd
("[SCSI] zfcp: Automatically attach remote ports")]
Instead make the accounting of missing SRBs atomic for parallel execution
in both the ERP thread and adapter->stat_work.
Signed-off-by: Steffen Maier <maier@linux.ibm.com> Fixes: d26ab06ede83 ("[SCSI] zfcp: receiving an unsolicted status can lead to I/O stall") Cc: <stable@vger.kernel.org> #2.6.27+ Reviewed-by: Jens Remus <jremus@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The function of_find_node_by_path() acquires a reference to the node
returned by it and that reference needs to be dropped by its caller.
su_get_type() doesn't do that. The match node are used as an identifier
to compare against the current node, so we can directly drop the refcount
after getting the node from the path as it is not used as pointer.
Fix this by use a single variable and drop the refcount right after
of_find_node_by_path().
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When netxen_rom_fast_read() fails, "bios" is left uninitialized and may
contain random value, thus should not be used.
The fix ensures that if netxen_rom_fast_read() fails, we return "-EIO".
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The gpio IP on Armada 370 at offset 0x18180 has neither a clk nor pwm
registers. So there is no need for a clk as the pwm isn't used anyhow.
So only check for the clk in the presence of the pwm registers. This fixes
a failure to probe the gpio driver for the above mentioned gpio device.
Fixes: d38499530e5 ("fs: decouple READ and WRITE from the block layer ops") Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For the same reason as commit 25896d073d8a ("x86/build: Fix compiler
support check for CONFIG_RETPOLINE"), you cannot put this $(error ...)
into the parse stage of the top Makefile.
Perhaps I'd propose a more sophisticated solution later, but this is
the best I can do for now.
Link: https://lkml.org/lkml/2017/12/25/211 Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com> Reported-by: Bernd Edlinger <bernd.edlinger@hotmail.de> Reported-by: Qian Cai <cai@lca.pw> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Tested-by: Qian Cai <cai@lca.pw> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
mac80211 uses the frag list to build AMSDU. When freeing
the skb, it may not be really freed, since someone is still
holding a reference to it.
In that case, when TCP skb is being retransmitted, the
pointer to the frag list is being reused, while the data
in there is no longer valid.
Since we will never get frag list from the network stack,
as mac80211 doesn't advertise the capability, we can safely
free and nullify it before releasing the SKB.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>