Akash Goel [Mon, 29 Jun 2015 09:20:20 +0000 (14:50 +0530)]
drm/i915/skl: Ring frequency table programming changes
Ring frequency table programming changes for SKL. No need for a
floor on ring frequency, as the issue of performance impact with
ring running below DDR frequency, is believed to be fixed on SKL
v2: Removed the check for avoiding ring frequency programming for BXT (Rodrigo)
Akash Goel [Mon, 29 Jun 2015 09:20:19 +0000 (14:50 +0530)]
drm/i915/skl: Retrieve the Rpe value from Pcode
Read the efficient frequency (aka RPe) value through the the mailbox
command (0x1A) from the pcode, as done on Haswell and Broadwell.
The turbo minimum frequency softlimit is not revised as per the
efficient frequency value.
v2: Replaced the conditional expression operator with 'if' statement (Tom)
v3: Corrected the derivation of efficient frequency & shifted the
GEN9_FREQ_SCALER multiplications downwards (Ville)
fbdev_set_par is called when fbcon is taking over control.
In the past frontbuffer was being invalidated on
set_to_gtt_domain, but it moved to set_domain fixing that case,
but left this behind and broken in
drm/i915: Unconditionally do fb tracking invalidate in set_domain
Note that even before this commit it wasn't perfect since the
invalidate was omitted if the fbcon was already in the GTT domain,
which it usually was.
Since we are also invalidating in other fbdev cases this one
was masked here. At least until now that I found this corner
case: On boot with plymouth doing a splash screen
when returning to the console frontbuffer wans't being invalidated
causing missed screen updates with PSR enabled.
So this patch fixes this issue.
v2: Make invalidate directly and unconditionally and
fix commit message indicating the set_domain fix
as pointed out by Daniel.
v3: Remove unecessary if(obj) added by mistake
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Try to clarify commit message a bit and make it clear the
referenced commit made this worse.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Idle frames the number of identical frames needed
before panel can enter PSR.
There are some panels that requires up to minimum of 4 idle
frames available on the market. For these cases usually
VBT should be used to configure the number of idle frames,
but unfortunately this isn't always true and VBT isn't being
set at all.
Let's trust VBT when it is set + 1 and use minimum of 4 + 1
when VBT isn't set. "+1" covers the "of-by-one" case.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By Spec we should only mask memup and hotplug detection
for hardware tracking cases. However we always masked
LPSP because with power well always enabled on audio
PSR was never being activated and residency was always
zeroed.
Apparently audio driver is tying power well management
and runtime PM for some reason. But with audio runtime
PM working or with audio completely out of picture
we should remove this mask, otherwise we have a high
risk of miss screen updates as faced by Matthew.
WARNING: With this patch if snd_intel_hda driver is
running and not releasing power well properly PSR will
constant Exit and Performance Counter will be 0.
But the best thing of this patch is that with one more
HW tracking working the risks of missed blank screen
are minimized at most.
This affects just core platforms where PSR exit are also
helped by HW tracking: Haswell, Broadwell and Skylake
for now.
v2: Fix commit message explanation. It has nothing to do
with runtime PM on i915 as previously advertised.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's do a frontbuffer flush on dirty fb.
To be used for DIRTYFB drm ioctl.
This patch solves the biggest PSR known issue, that is
missed screen updates during boot, mainly when there is a splash
screen involved like Plymouth.
Previously PSR was being invalidated by fbdev and Plymounth
was taking control with PSR yet invalidated and could get screen
updates normally. However with some atomic modeset changes
Pymouth modeset over ioctl was now causing frontbuffer flushes
making PSR gets back to work while it cannot track the
screen updates and exit properly.
By adding this flush on dirtyfb we properly track frontbuffer
writes and properly exit PSR.
Actually all mmap_wc users should call this dirty callback
in order to have a proper frontbuffer tracking.
In the future it can be extended to return 0 if the whole
screen has being flushed or the number of rects flushed
as Chris suggested.
v2: Remove ORIGIN_FB_DIRTY and use ORIGIN_GTT instead since dirty
callback is just called after few screen updates and not on
everyone as pointed by Daniel.
v3: Use flush instead of invalidate since flush means
invalidate + flush and dirty means drawn had finished and
it can be flushed.
v4: Remove PSR from subject since it is purely frontbuffer tracking
change and that can be useful for FBC as well.
Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix alignment as spotted by Paulo.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since flush actually means invalidate + flush we need to force psr
exit on PSR flush.
On Core platforms there is no way to disable hw tracking and
do the pure sw tracking so we simulate it by fully disable psr and
reschedule a enable back.
So a good idea is to minimize sequential disable/enable in cases we
know that HW tracking like when flush has been originated by a flip.
Also flip had just invalidated it already.
It also uses origin to minimize the a bit the amount of
disable/enabled, mainly when flip already had invalidated.
With this patch in place it is possible to do a flush on dirty areas
properly in a following patch.
v2: Remove duplicated exit on HSW+Sprites as pointed out by Paulo.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Add origin to frontbuffer tracking flush
This will be useful to PSR and FBC once we start making
dirty fb calls to also flush frontbuffer.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Update wa_ctx_emit() macro as per kernel coding guidelines
wa_ctx_emit() depends on the name of a local variable; if the name of that
variable is changed then we get compile errors. In this case it is unlikely
to be changed as this macro is only used in this set of functions but
Kernel coding guidelines doesn't recommend doing this. It was my mistake
as I should have corrected it at the beginning but missed so correct
this before there are more usages of this macro (Bob Beckett).
https://www.kernel.org/doc/Documentation/CodingStyle,
Chapter 12, "Things to avoid when using macros", point 2):
"
2) macros that depend on having a local variable with a magic name:
#define FOO(val) bar(index, val)
might look like a good thing, but it's confusing as hell when one reads the
code and it's prone to breakage from seemingly innocent changes.
"
v2: Optimization to avoid multiple evaluation of 'index' in the macro.
Since we invoke it multiple times, compiler, if it can, should be able to coalesce
them into a single condition and remove multiple WARN_ON checks (Chris).
Suggested-by: Robert Beckett <robert.beckett@intel.com> Cc: Robert Beckett <robert.beckett@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Imre Deak <imre.deak@intel.com> Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Handle HPD when it has actually occurred
Writing to PCH_PORT_HOTPLUG for each interrupt is not required.
Handle it only if hpd has actually occurred like we handle other
interrupts.
v2: Make few variables local to if block (Ville)
v3: Add check for ibx/cpt both (Ville).
While at it, remove the redundant check for hotplug_trigger from
pch_get_hpd_pins
v4: Indentation (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Sonika Jindal <sonika.jindal@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Tue, 7 Jul 2015 18:26:08 +0000 (15:26 -0300)]
drm/i915: move set_no_fbc_reason() call out of intel_fbc_find_crtc()
So now all the calls are inside __intel_fbc_update(). Consistency!
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Tue, 7 Jul 2015 18:26:07 +0000 (15:26 -0300)]
drm/i915: extract FBC_MULTIPLE_PIPES check
I have two separate refactor ideas that require extracting this to a
separate function. I'm not sure which idea I'll end choosing, but
since both will require extracting this function, let's do this now.
Notice that this is just code moving. Any possible problems with the
current multiple pipes check should be fixed in later commits.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Tue, 7 Jul 2015 18:26:06 +0000 (15:26 -0300)]
drm/i915: add FBC_IN_DBG_MASTER no_fbc_reason
The poor in_dbg_master() check was the only one without a reason
string. Give it a reason string so it won't feel excluded.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Tue, 7 Jul 2015 18:26:05 +0000 (15:26 -0300)]
drm/i915: use intel_crtc for the FBC functions
This is all internal i915.ko work, let's start using intel_crtc for
everything.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Tue, 7 Jul 2015 18:26:04 +0000 (15:26 -0300)]
drm/i915: use dev_priv for the FBC functions
Because the cool kids use dev_priv and FBC wants to be cool too.
We've been historically using struct drm_device on the FBC function
arguments, but we only really need it for intel_vgpu_active(): we can
use dev_priv everywhere else. So let's fully switch to dev_priv since
I'm getting tired of adding "struct drm_device *dev = dev_priv->dev"
everywhere.
If I get a NACK here I'll propose the opposite: convert all the
functions that currently take dev_priv to take dev.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Tue, 7 Jul 2015 18:26:03 +0000 (15:26 -0300)]
drm/i915: move FBC vfuncs to struct i915_fbc
Because it makes more sense there, IMHO.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Tue, 7 Jul 2015 09:44:32 +0000 (11:44 +0200)]
drm/i915: Inline SUPPORTS_DIGITAL_OUTPUTS
After the register save/restore code is gone there's just one user
left and it just obfuscates that one. Remove it.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Tue, 7 Jul 2015 07:10:40 +0000 (09:10 +0200)]
drm/i915: s/mdelay/msleep/
Burning cpu cycles isn't awesome, so use sleeps instead.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Tue, 7 Jul 2015 07:10:07 +0000 (09:10 +0200)]
drm/i915: Ditch SUPPORTS_INTEGRATED_HDMI|DP and use IS_G4X instead
Since that's really what we want to test for. Note remove the gen5
case doesn't change anything: In intel_setup_outputs ilk is handled
already in the HAS_PCH_SPLIT case, and the register save/restore code
touches registers which simply doesn't exist anymore at all.
v2: Drop UMS parts.
v3: Update commit message to reflect that the reg save/restore code is
gone (Ville).
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Matt Roper [Mon, 6 Jul 2015 16:19:24 +0000 (09:19 -0700)]
drm/i915: Don't dereference NULL plane while setting up scalers
intel_atomic_setup_scalers() dereferences 'plane' before the plane has
been assigned. The plane ID assignment doing this dereference is only
needed for debugging messages later in the function, so just move the
assignment farther down the function to a point where plane will no
longer be NULL.
drm/i915: Clean up intel_atomic_setup_scalers slightly.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Bob Paauwe <bob.j.paauwe@intel.com> Reported-by: Bob Paauwe <bob.j.paauwe@intel.com> Signed-off-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Mon, 6 Jul 2015 08:09:25 +0000 (11:09 +0300)]
drm/i915: Mark elsps submitted when they are pushed to hw
Now when we have requests this deep on call chain, we can mark
the elsp being submitted when it actually is. Remove temp variable
and readjust commenting to more closely fit to the code.
v2: Avoid tmp variable and reduce number of writes (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Fri, 3 Jul 2015 14:09:37 +0000 (17:09 +0300)]
drm/i915: Convert execlists_ctx_descriptor() for requests
Pass around requests to carry context deeper in callchain.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Fri, 3 Jul 2015 14:09:36 +0000 (17:09 +0300)]
drm/i915: Convert execlists_elsp_writ() for requests
Pass around requests to carry context deeper in callchain.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Fri, 3 Jul 2015 14:09:35 +0000 (17:09 +0300)]
drm/i915: Convert intel_lr_context_pin() for requests
Pass around requests to carry context deeper in callchain.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Mon, 6 Jul 2015 08:08:30 +0000 (11:08 +0300)]
drm/i915: Assign request ringbuf before pin
In preparation to make intel_lr_context_pin|unpin to accept
requests, assign ringbuf into request before we call the pinning.
v2: No need to unset ringbuf on error path (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Fri, 3 Jul 2015 14:09:33 +0000 (17:09 +0300)]
drm/i915: Convert execlists_update_context() for requests
Pass around requests to carry context deeper in callchain.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Fri, 3 Jul 2015 14:09:32 +0000 (17:09 +0300)]
drm/i915: Convert execlist_submit_contexts() for requests
Pass around requests to carry context deeper in callchain.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Also perform gpu reset under execlist mode.
It is found that i915 will not reset gpu under execlist mode when
unload module. that will lead to some issues when unload/load module
with different submission mode. e.g. from execlist mode to ring
buffer mode via loading/unloading i915. Because HW is not in a reset
state and registers are not clean under such condition.
Signed-off-by: Niu,Bing <bing.niu@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In this WA we need to set GEN8_L3SQCREG4[21:21] and reset it after PIPE_CONTROL
instruction but there is a slight complication as this is applied in WA batch
where the values are only initialized once.
Dave identified an issue with the current implementation where the register value
is read once at the beginning and it is reused; this patch corrects this by saving
the register value to memory, update register with the bit of our interest and
restore it back with original value.
This implementation uses MI_LOAD_REGISTER_MEM which is currently only used
by command parser and was using a default length of 0. This is now updated
with correct length and moved to appropriate place.
Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Dave Gordon <david.s.gordon@intel.com> Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Fri, 3 Jul 2015 18:40:54 +0000 (15:40 -0300)]
drm/i915: protect FBC functions with FBC checks
Now all the functions called by other files check whether FBC has been
initialized. This allows us to drop the checks on the static
functions.
v2:
- s/HAS_FBC/dev_priv->display.enable_fbc/ everywhere but the init
function (Chris).
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Thu, 2 Jul 2015 22:25:13 +0000 (19:25 -0300)]
drm/i915: FBC doesn't need struct_mutex anymore
Everything is covered either by fbc.lock or mm.stolen_lock, and
intel_fbc.c is already responsible for grabbing the appropriate locks
when it needs them.
Reviewed-by: Chris wilson <chris@chris-wilson.co.uk> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Thu, 2 Jul 2015 22:25:12 +0000 (19:25 -0300)]
drm/i915: intel_unregister_dsm_handler() doesn't need struct_mutex
So don't grab the lock before calling the function.
Reviewed-by: Chris wilson <chris@chris-wilson.co.uk> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Thu, 2 Jul 2015 22:25:11 +0000 (19:25 -0300)]
drm/i915: intel_frontbuffer_flip_prepare() doesn't need struct_mutex
So release the lock earlier.
Reviewed-by: Chris wilson <chris@chris-wilson.co.uk> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Thu, 2 Jul 2015 22:25:10 +0000 (19:25 -0300)]
drm/i915: add the FBC mutex
Make sure we're not going to have weird races in really weird cases
where a lot of different CRTCs are doing rendering and modesets at the
same time.
With this change and the stolen_lock from the previous patch, we can
start removing the struct_mutex locking we have around FBC in the next
patches.
v2:
- Rebase (6 months later)
- Also lock debugfs and stolen.
v3:
- Don't lock a single value read (Chris).
- Replace lockdep assertions with WARNs (Daniel).
- Improve commit message.
- Don't forget intel_pre_plane_update() locking.
v4:
- Don't remove struct_mutex at intel_pre_plane_update() (Chris).
- Add comment regarding locking dependencies (Chris).
- Rebase after the stolen code rework.
- Rebase again after drm-intel-nightly changes.
v5:
- Rebase after the new stolen_lock patch.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v4) Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Thu, 2 Jul 2015 22:25:09 +0000 (19:25 -0300)]
drm/i915: add dev_priv->mm.stolen_lock
Which should protect dev_priv->mm.stolen usage. This will allow us to
simplify the relationship between stolen memory, FBC and struct_mutex.
v2:
- Rebase after the stolen_remove_node() dev_priv patch move.
- I realized that after we fixed a few things related to the FBC CFB
size checks, we're not reallocating the CFB anymore with FBC
enabled, so we can just move all the locking to i915_gem_stolen.c
and stop worrying about freezing all the stolen alocations while
freeing/rellocating the CFB. This allows us to fix the "Too
coarse" observation from Chris.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Thu, 2 Jul 2015 22:25:08 +0000 (19:25 -0300)]
drm/i915: move FBC code out of i915_gem_stolen.c
With the abstractions created by the last patch, we can move this code
and the only thing inside intel_fbc.c that knows about dev_priv->mm is
the code that reads stolen_base.
We also had to move a call to i915_gem_stolen_cleanup_compression()
- now called intel_fbc_cleanup_cfb() - outside i915_gem_stolen.c.
v2:
- Rebase after the remove_node() changes on the previous patch.
Requested-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Thu, 2 Jul 2015 22:25:07 +0000 (19:25 -0300)]
drm/i915: add simple wrappers for stolen node insertion/removal
We want to move the FBC code out of i915_gem_stolen.c, but that code
directly adds/removes stolen memory nodes. Let's create this
abstraction, so i915_gme_stolen.c is still in control of all the
stolen memory handling. The abstraction will also allow us to add
locking assertions later.
v2:
- Add dev_priv as remove_node() argument since we'll need it later
(Chris).
Requested-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Try to make sure cxsr is disabled around plane
enable/disable
This fixes a load of warnings from the frontbuffer tracking.
Testcase: igt/kms_frontbuffer_tracking/fbc-1p-rte Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Tested-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Thu, 2 Jul 2015 14:43:25 +0000 (17:43 +0300)]
drm/i915/opregion: start using extended didl
Adding support for did2, or the extended support display devices ID
list, increases the total to 15.
Signed-off-by: Jani Nikula <jani.nikula@intel.com> Acked-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Thu, 2 Jul 2015 14:43:24 +0000 (17:43 +0300)]
drm/i915/opregion: abstract didl and did2 getter and setter
Make it easier to handle the extended didl. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Thu, 2 Jul 2015 14:43:23 +0000 (17:43 +0300)]
drm/i915/opregion: prefer DRM logging functions over pr_warn and dev_dbg
Conform to same style as the rest of the driver.
Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Thu, 2 Jul 2015 14:43:22 +0000 (17:43 +0300)]
drm/i915/opregion: add new opregion stuff
Inluding extended didl and cpdl fields
Present since opregion version 3.0.
Signed-off-by: Jani Nikula <jani.nikula@intel.com> Acked-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Thu, 2 Jul 2015 14:43:21 +0000 (17:43 +0300)]
drm/i915/opregion: use BUILD_BUG_ON to verify mailbox struct sizes
Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Fri, 3 Jul 2015 15:31:30 +0000 (12:31 -0300)]
drm/i915: set FDI translations to NULL on SKL
drivers/gpu/drm/i915/intel_ddi.c: In function ‘intel_prepare_ddi’:
drivers/gpu/drm/i915/intel_ddi.c:517:6: warning:
‘ddi_translations_fdi’ may be used uninitialized in this function
[-Wmaybe-uninitialized]
if (ddi_translations_fdi)
^
drivers/gpu/drm/i915/intel_ddi.c:446:30: note: ‘ddi_translations_fdi’
was declared here
const struct ddi_buf_trans *ddi_translations_fdi;
^
This line used to be there, but was removed by:
commit f8896f5d58e64bfd3c2b5f7c5ba5c3f3967e93c7
Author: David Weinehall <david.weinehall@linux.intel.com>
Date: Thu Jun 25 11:11:03 2015 +030
drm/i915/skl: Buffer translation improvements
Cc: David Weinehall <david.weinehall@linux.intel.com> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Expose I915_EXEC_RESOURCE_STREAMER flag and getparam
Ensures that the batch buffer is executed by the resource streamer.
And will let userspace know whether Resource Streamer is supported in
the kernel.
v2: Don't skip 1<<15 for the exec flags (Jani Nikula)
v3: Use HAS_RESOURCE_STREAMER macro for execbuf validation (Chris Wilson)
(from getparam patch)
v2: Update I915_PARAM_HAS_RESOURCE_STREAMER so it's after
I915_PARAM_HAS_GPU_RESET.
v3: Only advertise RS support for hardware that supports it.
v4: Add HAS_RESOURCE_STREAMER() macro (Chris)
Testcase: igt/gem_exec_params Cc: Jani Nikula <jani.nikula@intel.com> Cc: Kenneth Graunke <kenneth@whitecape.org> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
[danvet: squash in getparam patch since it'd break bisect, suggested
by Chris.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Abdiel Janulgue [Tue, 16 Jun 2015 10:39:42 +0000 (13:39 +0300)]
drm/i915: Enable resource streamer on Execlists
GEN8 and above uses Execlists by default instead of the legacy
ringbuffer for batch execution. This patch enables the resource
streamer bits when required.
Patch is based on the initial work by Minu Mathai <minu.mathai@intel.com>
This version also adds the required bits to enable GEN8 Resource
Streamer context save and restore for Execlists.
Abdiel Janulgue [Tue, 16 Jun 2015 10:39:41 +0000 (13:39 +0300)]
drm/i915: Enable Resource Streamer state save/restore on MI_SET_CONTEXT
Also clarify comments on context size that the extra state for
Resource Streamer is included.
v2: Don't remove the extended save/restore enabled for older
platforms. (Ville)
Use new MI_SET_CONTEXT defines for HSW RS save/restore state
instead of extended save/restore. (Daniel)
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Abdiel Janulgue <abdiel.janulgue@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Abdiel Janulgue [Tue, 16 Jun 2015 10:39:40 +0000 (13:39 +0300)]
drm/i915: Enable resource streamer bits on MI_BATCH_BUFFER_START
Adds support for enabling the resource streamer on the legacy
ringbuffer for HSW and GEN8.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Abdiel Janulgue <abdiel.janulgue@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch contains changes based on 2 updates to the spec:
Port PLL VCO restriction raised up to 6700.
Port PLL now needs DCO amp override enable for all VCO frequencies.
v2: Sonika's review comment addressed
- dcoampovr_en_h variable not required
Based on a discussion with Siva, the following changes have been made.
- replace dco_amp var with #define BXT_DCO_AMPLITUDE
- set pll10 in a single assignment
v3:
Move DCO amplitude default value to i915_reg.h. Suggested by Siva.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> Reviewed-by: Sonika Jindal <sonika.jindal@intel.com> [v2]
[danvet: Spell out BUN since not everyone knows what this means.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Rebased due to CHV/BXT port clock check improvemnts
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-and-tested-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 30 Jun 2015 16:23:59 +0000 (19:23 +0300)]
drm/i915: Account for CHV/BXT DPLL clock limitations
CHV/BXT DPLL can't generate frequencies in the 216-240 MHz range.
Account for that when checking whether the HDMI port clock is valid.
This is particularly important for BXT since it can otherwise do
12bpc, and standard 1920x1080p60 CEA modes land right in the middle
of that range when the clock gets multiplied to account for 12bpc.
With the extra checks we will now filter out any mode where both
8bpc and 12bpc clock are within the gap. During modeset we then
pick whichever mode works, favoring 12bpc if both are possible.
12bpc isn't supported on CHV so we simply end up filtering out any
mode where the 8bpc port clock is in the gap.
v2: Fix crtc_clock vs. port_clock fumble in compute_config() (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-and-tested-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 30 Jun 2015 12:33:52 +0000 (15:33 +0300)]
drm/i915: Bump HDMI min port clock to 25 MHz
Increase the HDMI port minimum port clock from 20 to 25 MHz. This is
is the minimum listed in the DVI/HDMI specs, and it's also the
documented minimum DPLL frequency for most of our platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-and-tested-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 30 Jun 2015 12:33:51 +0000 (15:33 +0300)]
drm/i915: Fix HDMI 12bpc and pixel repeat clock readout for DDI platforms
Take the HDMI 12bpc mode and pixel repeat into account when extracting
the dotclock from the hardware on DDI platforms.
Tested on HSW only.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-and-tested-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Markus Elfring [Sun, 5 Jul 2015 19:55:10 +0000 (21:55 +0200)]
GPU-DRM: Delete an unnecessary check before drm_property_unreference_blob()
The drm_property_unreference_blob() function tests whether its argument
is NULL and then returns immediately.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Reviewed-by: Zhao Junwang <zhjwpku@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Tue, 30 Jun 2015 15:16:40 +0000 (18:16 +0300)]
drm/i915/gtt: Per ppgtt scratch page
Previously we have pointed the page where the individual ppgtt
scratch structures refer to, to be the instance which GGTT setup have
allocated. So it has been shared.
To achieve full isolation between ppgtts also in this regard,
allocate per ppgtt scratch page.
Cc: Michel Thierry <michel.thierry@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Michel Thierry <michel.thierry@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Changes required to enable DSI Video Mode on CHT
On CHT, changes are required for calculating the correct m,n & p with
minimal error +/- for the required DSI clock, so that the correct
dividor & ctrl values are written in cck regs for DSI. This patch has
been tested on CHT RVP with 1200 x 1920 panel.
v2 by Jani, rebased on earlier refactoring, original at [1].
For MIPI panels requiring higher DSI clk, values needs to be added
in lfsr_converts table for getting the correct values of pll ctrl
and dividor values which gets programmed in cck regs, otherwise DSI
PLL does not get locked leading to no display on the MIPI panel.
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Wed, 1 Jul 2015 12:58:50 +0000 (15:58 +0300)]
drm/i915/dsi: abstract dsi bpp derivation from pixel format
Nuke three copies of the same switch case.
Hopefully we can switch to a drm generic function later on, but that
will require us to swich to enum mipi_dsi_pixel_format first.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Tue, 30 Jun 2015 13:53:05 +0000 (10:53 -0300)]
drm/i915: don't increment the FBC threshold at fbc_enable
We first set the threshold value when we're allocating the CFB, and
then later at {ilk,gen7}_fbc_enable() we increment it in case we're
using 16bpp. While that is correct, it is dangerous: if we rework the
code a little bit in a way that allows us to call intel_fbc_enable()
without necessarily calling i915_gem_stolen_setup_compression() first,
we might end up incrementing threshold more than once. To prevent
that, increment a temporary variable instead.
v2: Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently only normal views were accounted which under-accounts
the usage as reported in debugfs.
Introduce new helper, i915_gem_obj_total_ggtt_size, and use it
from call sites which want to know how much GGTT space are
objects using.
v2: Single loop in i915_gem_get_aperture_ioctl. (Chris Wilson)
v3: Walk GGTT active/inactive lists in i915_gem_get_aperture_ioctl
for better efficiency. (Chris Wilson, Daniel Vetter)
v4: Make i915_gem_obj_total_ggtt_size private to debugfs. (Chris Wilson)
v5: Change unsigned long to u64. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Tue, 30 Jun 2015 15:16:39 +0000 (18:16 +0300)]
drm/i915/gtt: Return struct i915_scratch_page from alloc_scratch
Every other alloc_* function return the pointer to the page
they alloc. Follow the convention with scratch page also.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Michel Thierry <michel.thierry@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Maintain base page handling functions in order of
alloc, free, init. No functional changes.
v2: s/Introduce/Maintain (Michel)
v3: Rebase
Cc: Michel Thierry <michel.thierry@intel.com> Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Michel Thierry <michel.thierry@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
John Harrison [Tue, 30 Jun 2015 11:40:55 +0000 (12:40 +0100)]
drm/i915: Reserve space improvements
An earlier patch was added to reserve space in the ring buffer for the
commands issued during 'add_request()'. The initial version was
pessimistic in the way it handled buffer wrapping and would cause
premature wraps and thus waste ring space.
This patch updates the code to better handle the wrap case. It no
longer enforces that the space being asked for and the reserved space
are a single contiguous block. Instead, it allows the reserve to be on
the far end of a wrap operation. It still guarantees that the space is
available so when the wrap occurs, no wait will happen. Thus the wrap
cannot fail which is the whole point of the exercise.
Also fixed a merge failure with some comments from the original patch.
v2: Incorporated suggestion by David Gordon to move the wrap code
inside the prepare function and thus allow a single combined
wait_for_space() call rather than doing one before the wrap and
another after. This also makes the prepare code much simpler and
easier to follow.
v3: Fix for 'effective_size' vs 'size' during ring buffer remainder
calculations (spotted by Tomas Elf).
For: VIZ-5115 CC: Daniel Vetter <daniel@ffwll.ch> Signed-off-by: John Harrison <John.C.Harrison@Intel.com> Reviewed-by: Tomas Elf <tomas.elf@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Mon, 22 Jun 2015 20:35:52 +0000 (23:35 +0300)]
drm/i915/bxt: add DDI port HW readout support
Add support for reading out the HW state for DDI ports. Since the actual
programming is very similar to the CHV/VLV DPIO PLL programming we can
reuse much of the logic from there.
This fixes the state checker failures I saw on my BXT with HDMI output.
v2:
- rebased on v2 of patch 4/5
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Mon, 22 Jun 2015 20:35:51 +0000 (23:35 +0300)]
drm/i915: calculate the port clock rate along with other PLL params
Depending on the platform the port clock fed to the pipe can be the PLL's
post-divided fast clock rate or a /5 divided version of it. To make this
more obvious across the platforms calculate this port clock along with
the rest of the PLL parameters.
This is also needed by the next patch where we can reuse the CHV helper
for the BXT PLL HW readout code; so export the corresponding helper.
While at it also add a more descriptive name to the helpers and a
comment explaining what's being calculated.
No functional change.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
David Weinehall [Thu, 25 Jun 2015 08:11:03 +0000 (11:11 +0300)]
drm/i915/skl: Buffer translation improvements
This patch adds support for 0.85V VccIO on Skylake Y,
separate buffer translation tables for Skylake U,
and support for I_boost for the entries that needs this.
Changes in v2:
* Refactored the code a bit to move all DDI signal level setup to
intel_ddi.c
Issue: VIZ-5677 Signed-off-by: David Weinehall <david.weinehall@linux.intel.com> Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
[danvet: Apply style polish checkpatch suggested.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 24 Jun 2015 19:00:10 +0000 (22:00 +0300)]
drm/i915: Zero unused WM1 watermarks on VLV/CHV
The hardware supposedly ignores the WM1 watermarks while the PND
deadline mode is enabled, but clear out the register just in case.
This is what the other OS does, and it does make register dumps look
more consistent when we don't have partial WM1 values lingering in
the registers (some WM1 watermarks already get zeroed when the actually
used DSPFW registers get written).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 24 Jun 2015 19:00:09 +0000 (22:00 +0300)]
drm/i915: Add debugfs knobs for VLVCHV memory latency values
Allow tweaking the VLV/CHV memory latencies thorugh sysfs, like we do
for ILK+.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 24 Jun 2015 19:00:08 +0000 (22:00 +0300)]
drm/i915: Don't do PM5/DDR DVFS with multiple pipes
Enabling PM5/DDR DVFS with multiple active pipes isn't a validated
configuration. It does seem to work most of the time at least, but
there is clearly an additional risk of underruns, so let's not play
with fire.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 24 Jun 2015 19:00:07 +0000 (22:00 +0300)]
drm/i915: Try to make sure cxsr is disabled around plane enable/disable
CxSR (or maxfifo on VLV/CHV) blocks somne changes to the plane control
register (enable bit at least, not quite sure about the rest). So in
order to have the plane enable/disable when we want we need to first
kick the hardware out of cxsr.
Unfortunateloy this requires some extra vblank waits. For the CxSR
enable after the plane update we should eventually use an async
vblank worker, but since we don't have that just do sync vblank
waits. For the disable case we have no choice but to do it
synchronously.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 24 Jun 2015 19:00:06 +0000 (22:00 +0300)]
drm/i915: Use the memory latency based WM computation on VLV too
In order to get decnet memory self refresh residency on VLV, flip it
over to the new CHV way of doing things. VLV doesn't do PM5 or DDR DVFS
so it's a bit simpler.
I'm not sure the currently memory latency used for CHV is really
appropriate for VLV. Some further testing will probably be needed to
figure that out.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 24 Jun 2015 19:00:05 +0000 (22:00 +0300)]
drm/i915: Compute display FIFO split dynamically for CHV
Consider which planes are active and compute the FIFO split based on the
relative data rates. Since we only consider the pipe src width rather
than the plane width when computing watermarks it seems best to do the
same when computing the FIFO split as well. This means the only thing we
actually have to consider for the FIFO splut is the bpp, and we can
ignore the rest.
I've just stuffed the logic into the watermark code for now. Eventually
it'll need to move into the atomic update for the crtc.
There's also one extra complication I've not yet considered; Some of the
DSPARB registers contain bits related to multiple pipes. The registers
are double buffered but apparently they update on the vblank of any
active pipe. So doing the FIFO reconfiguration properly when multiple
pipes are active is not going to be fun. But let's ignore that mess for
now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 24 Jun 2015 19:00:04 +0000 (22:00 +0300)]
drm/i915: CHV DDR DVFS support and another watermark rewrite
Turns out the VLV/CHV system agent doesn't understand memory
latencies, so trying to rely on the PND deadline mechanism is not
going to fly especially when DDR DVFS is enabled. Currently we try to
avoid the problems by lying to the system agent about the deadlines
and setting the FIFO watermarks to 8 cachelines. This however leads to
bad memory self refresh residency.
So in order to satosfy everyone we'll just give up on the deadline
scheme and program the watermarks old school based on the worst case
memory latency.
I've modelled this a bit on the ILK+ approach where we compute multiple
sets of watermarks for each pipe (PM2,PM5,DDR DVFS) and when merge thet
appropriate one later with the watermarks from other pipes. There isn't
too much to merge actually since each pipe has a totally independent
FIFO (well apart from the mess with the partially shared DSPARB
registers), but still decopuling the pipes from each other seems like a
good idea.
Eventually we'll want to perform the watermark update in two phases
around the plane update to avoid underruns due to the single buffered
watermark registers. But that's still in limbo for ILK+ too, so I've not
gone that far yet for VLV/CHV either.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 24 Jun 2015 19:00:03 +0000 (22:00 +0300)]
drm/i915: Read wm values from hardware at init on CHV
Read out the current watermark settings from the hardware at driver init
time. This will allow us to compare the newly calculated values against
the currrent ones and potentially avoid needless WM updates.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 24 Jun 2015 19:00:02 +0000 (22:00 +0300)]
drm/i915: Split atomic wm update to pre and post variants
Try to update the watermarks on the right side of the plane update. This
is just a temporary hack until we get the proper two part update into
place. However in the meantime this might have some chance of at least
working.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Wed, 24 Jun 2015 19:00:01 +0000 (22:00 +0300)]
drm/i915: POSTING_READ() in intel_set_memory_cxsr()
We want cxsr exit to happen ASAP, so toss in some POSTING_READ()s to
make sure things are really kicked off.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Fri, 26 Jun 2015 17:35:16 +0000 (19:35 +0200)]
drm/i915: Unconditionally do fb tracking invalidate in set_domain
We can't elide the fb tracking invalidate if the buffer is already in
the right domain since that would lead to missed screen updates. I'm
pretty sure I've written this already before but must have gotten lost
unfortunately :(
v2: Chris observed that all internal set_domain users already
correctly do the fb invalidate on their own, hence we can move this
just into the set_domain ioctl instead.
v3: I screwed up setting the invalidate ORIGIN_* correctly (Chris).
Cc: Chris Wilson <chris@chris-wilson.co.uk> Reported-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rodrigo Vivi [Fri, 26 Jun 2015 20:55:54 +0000 (13:55 -0700)]
drm/i915: Fix IPS related flicker
We cannot let IPS enabled with no plane on the pipe:
BSpec: "IPS cannot be enabled until after at least one plane has
been enabled for at least one vertical blank." and "IPS must be
disabled while there is still at least one plane enabled on the
same pipe as IPS." This restriction apply to HSW and BDW.
However a shortcut path on update primary plane function
to make primary plane invisible by setting DSPCTRL to 0
was leting IPS enabled while there was no
other plane enabled on the pipe causing flickerings that we were
believing that it was caused by that other restriction where
ips cannot be used when pixel rate is greater than 95% of cdclok.
v2: Don't mess with Atomic path as pointed out by Ville.
v3: Rebase after a long time and atomic path changes.
Accept Ville suggestion of not check !fb
v4: Re-factore on dinq
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=85583 Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Kenneth Graunke <kenneth@whitecape.org>
[danvet: Make it compile] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Thu, 25 Jun 2015 15:15:06 +0000 (16:15 +0100)]
drm/i915/skl: Replace the HDMI DPLL divider computation algorithm
The HW validation team came back from further testing with a slightly
changed constraint on the deviation between the DCO frequency and the
central frequency. Instead of +-4%, it's now +1%/-6%.
Unfortunately, the previous algorithm didn't quite cope with these new
constraints, the reason being that it wasn't thorough enough looking at
the possible divider candidates.
The new algorithm looks at all dividers, which is definitely a hammer
approach (we could reduce further the set of dividers to good ones as a
follow up, at the cost of a bit more complicated code). But, at least,
we can now satisfy the +1%/+6% rule for all the "Well known" HDMI
frequencies of my test set (373 entries).
On that subject, the new code is quite extensively tested in
intel-gpu-tools (tools/skl_compute_wrpll).
v2: Fix cycling between central frequencies and dividers (Paulo)
Properly choose the minimal deviation between postive and negative
candidates (Paulo).
On the 373 test frequencies, v2 computes better dividers than v1 (ie
more even dividers and lower deviation on average):
v1: average deviation: 206.52
v2: average deviation: 194.47
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Michel Thierry [Wed, 10 Jun 2015 16:46:39 +0000 (17:46 +0100)]
drm/i915/gtt: Switch gen8_free_page_tables params
After Mika's ppgtt cleanup series, all the other free functions have
drm_device as the first parameter, except this one.
No functional changes.
Signed-off-by: Michel Thierry <michel.thierry@intel.com> Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Michel Thierry [Fri, 26 Jun 2015 12:46:14 +0000 (13:46 +0100)]
drm/i915/lrc: Update PDPx registers with lri commands
A safer way to update the PDPx registers is sending lri commands, added
in the ring before the batchbuffer start. Otherwise, the ctx must be idle
before trying to change anything (but the ring-tail) in the ctx image. An
example where the ctx won't be idle is lite-restore.
This patch depends on 5b7e4c9ce ("drm/i915/gtt: Mark TLBS dirty for gen8+").
v2: Combine lri writes (and save 8 commands). (Mika)
v3: Rebase after ring/req changes, and removed references to deprecated patches.
Cc: Dave Gordon <david.s.gordon@intel.com> Cc: Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by: Michel Thierry <michel.thierry@intel.com> Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Thu, 25 Jun 2015 15:35:19 +0000 (18:35 +0300)]
drm/i915/gtt: Use nonatomic bitmap ops
There is no need for atomicity here. Convert all bitmap
operations to nonatomic variants.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Michel Thierry <michel.thierry@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Thu, 25 Jun 2015 15:35:17 +0000 (18:35 +0300)]
drm/i915/gtt: Move scratch_pd and scratch_pt into vm struct
Scratch page is part of struct i915_address_space. Move other
scratch entities into the same struct. This is a preparatory patch
for having only one instance of each scratch_pt/pd.
v2: make commit msg more readable
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Michel Thierry <michel.thierry@intel.com> (v1)
[danvet: Bikeshed summary to avoid confusion with vmas.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Thu, 25 Jun 2015 15:35:16 +0000 (18:35 +0300)]
drm/i915/gtt: Cleanup page directory encoding
Write page directory entry without using superfluous
indirect function. Also remove unused device parameter
from the encode function.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Michel Thierry <michel.thierry@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
projects / mirror_ubuntu-kernels.git / log