The function batadv_bla_claim_dump_bucket must be able to handle
non-complete dumps of a single bucket. It tries to do that by saving the
latest dumped index in *idx_skip to inform the caller about the current
state.
But the caller only assumes that buckets were not completely dumped when
the return code is non-zero. This function must therefore also return a
non-zero index when the dumping of an entry failed. Otherwise the caller
will just skip all remaining buckets.
And the function must also reset *idx_skip back to zero when it finished a
bucket. Otherwise it will skip the same number of entries in the next
bucket as the previous one had.
Fixes: 04f3f5bf1883 ("batman-adv: add B.A.T.M.A.N. Dump BLA claims via netlink") Reported-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The function batadv_v_gw_dump stops the processing loop when
batadv_v_gw_dump_entry returns a non-0 return code. This should only
happen when the buffer is full. Otherwise, an empty message may be
returned by batadv_gw_dump. This empty message will then stop the netlink
dumping of gateway entries. At worst, not a single entry is returned to
userspace even when plenty of possible gateways exist.
Fixes: b71bb6f924fe ("batman-adv: add B.A.T.M.A.N. V bat_gw_dump implementations") Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The function batadv_iv_gw_dump stops the processing loop when
batadv_iv_gw_dump_entry returns a non-0 return code. This should only
happen when the buffer is full. Otherwise, an empty message may be
returned by batadv_gw_dump. This empty message will then stop the netlink
dumping of gateway entries. At worst, not a single entry is returned to
userspace even when plenty of possible gateways exist.
Fixes: efb766af06e3 ("batman-adv: add B.A.T.M.A.N. IV bat_gw_dump implementations") Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Once struct is added to per-netns list it becomes visible to other cpus,
so we cannot use kfree().
Also delay setting entries refcount to 1 until after everything is
initialised so that when we call clusterip_config_put() in this spot
entries is still zero.
A more sophisticated implementation could try to combine fragment checksums
when all fragments have CHECKSUM_COMPLETE and are split at even offsets.
For now, we just set ip_summed to CHECKSUM_NONE to avoid "hw csum failure"
warnings in the kernel log when fragmented frames are received. In
consequence, skb_pull_rcsum() can be replaced with skb_pull().
Note that in usual setups, packets don't reach batman-adv with
CHECKSUM_COMPLETE (I assume NICs bail out of checksumming when they see
batadv's ethtype?), which is why the log messages do not occur on every
system using batman-adv. I could reproduce this issue by stacking
batman-adv on top of a VXLAN interface.
Fixes: 610bfc6bc99b ("batman-adv: Receive fragmented packets and merge") Tested-by: Maximilian Wilhelm <max@sdn.clinic> Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
eth_type_trans() internally calls skb_pull(), which does not adjust the
skb checksum; skb_postpull_rcsum() is necessary to avoid log spam of the
form "bat0: hw csum failure" when packets with CHECKSUM_COMPLETE are
received.
Note that in usual setups, packets don't reach batman-adv with
CHECKSUM_COMPLETE (I assume NICs bail out of checksumming when they see
batadv's ethtype?), which is why the log messages do not occur on every
system using batman-adv. I could reproduce this issue by stacking
batman-adv on top of a VXLAN interface.
Fixes: c6c8fea29769 ("net: Add batman-adv meshing protocol") Tested-by: Maximilian Wilhelm <max@sdn.clinic> Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In handle_write_finished(), if r1_bio->bios[m] != NULL, it thinks
the corresponding conf->mirrors[m].rdev is also not NULL. But, it
is not always true.
Even if some io hold replacement rdev(i.e. rdev->nr_pending.count > 0),
raid1_remove_disk() can also set the rdev as NULL. That means,
bios[m] != NULL, but mirrors[m].rdev is NULL, resulting in NULL
pointer dereference in handle_write_finished and sync_request_write.
There is a potential deadlock if mount/umount happens when
raid5_finish_reshape() tries to grow the size of emulated disk.
How the deadlock happens?
1) The raid5 resync thread finished reshape (expanding array).
2) The mount or umount thread holds VFS sb->s_umount lock and tries to
write through critical data into raid5 emulated block device. So it
waits for raid5 kernel thread handling stripes in order to finish it
I/Os.
3) In the routine of raid5 kernel thread, md_check_recovery() will be
called first in order to reap the raid5 resync thread. That is,
raid5_finish_reshape() will be called. In this function, it will try
to update conf and call VFS revalidate_disk() to grow the raid5
emulated block device. It will try to acquire VFS sb->s_umount lock.
The raid5 kernel thread cannot continue, so no one can handle mount/
umount I/Os (stripes). Once the write-through I/Os cannot be finished,
mount/umount will not release sb->s_umount lock. The deadlock happens.
The raid5 kernel thread is an emulated block device. It is responible to
handle I/Os (stripes) from upper layers. The emulated block device
should not request any I/Os on itself. That is, it should not call VFS
layer functions. (If it did, it will try to acquire VFS locks to
guarantee the I/Os sequence.) So we have the resync thread to send
resync I/O requests and to wait for the results.
For solving this potential deadlock, we can put the size growth of the
emulated block device as the final step of reshape thread.
2017/12/29:
Thanks to Guoqing Jiang <gqjiang@suse.com>,
we confirmed that there is the same deadlock issue in raid10. It's
reproducible and can be fixed by this patch. For raid10.c, we can remove
the similar code to prevent deadlock as well since they has been called
before.
Reported-by: Alex Wu <alexwu@synology.com> Reviewed-by: Alex Wu <alexwu@synology.com> Reviewed-by: Chung-Chiang Cheng <cccheng@synology.com> Signed-off-by: BingJing Chang <bingjingc@synology.com> Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
i_dir_seq is subject to concurrent modification by a cmpxchg or
store-release operation, so ensure that the relaxed access in
d_alloc_parallel uses READ_ONCE.
Reported-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If d_alloc_parallel runs concurrently with __d_add, it is possible for
d_alloc_parallel to continuously retry whilst i_dir_seq has been
incremented to an odd value by __d_add:
CPU0:
__d_add
n = start_dir_add(dir);
cmpxchg(&dir->i_dir_seq, n, n + 1) == n
CPU0:
__d_lookup_done(dentry)
hlist_bl_lock
bit_spin_lock(0, (unsigned long *)b); // Never succeeds
CPU1:
if (unlikely(parent->d_inode->i_dir_seq != seq)) {
hlist_bl_unlock(b);
goto retry;
}
Since the simple bit_spin_lock used to implement hlist_bl_lock does not
provide any fairness guarantees, then CPU1 can starve CPU0 of the lock
and prevent it from reaching end_dir_add(dir), therefore CPU1 cannot
exit its retry loop because the sequence number always has the bottom
bit set.
This patch resolves the livelock by not taking hlist_bl_lock in
d_alloc_parallel if the sequence counter is odd, since any subsequent
masked comparison with i_dir_seq will fail anyway.
Cc: Peter Zijlstra <peterz@infradead.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Reported-by: Naresh Madhusudana <naresh.madhusudana@arm.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Although L2 is in halt state, it will be in the active state after
VM entry if the VM entry is vectoring according to SDM 26.6.2 Activity
State. Halting the vcpu here means the event won't be injected to L2
and this decision isn't reported to L1. Thus L0 drops an event that
should be injected to L2.
Commit d02fd6e7d293 ("macvlan: Fix one possible double free") handles
the case when register_netdevice() invokes ndo_uninit() on error and
as a result free the port. But 'macvlan_port_get_rtnl(dev))' check
(returns dev->rx_handler_data), which was added by this commit in order
to prevent double free, is not quite correct:
* for macvlan it always returns NULL because 'lowerdev' is the one that
was used to register rx handler (port) in macvlan_port_create() as
well as to unregister it in macvlan_port_destroy().
* for macvtap it always returns a valid pointer because macvtap registers
its own rx handler before macvlan_common_newlink().
Fixes: d02fd6e7d293 ("macvlan: Fix one possible double free") Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
do_task_stat() calls get_wchan(), which further does unwind_frame().
unwind_frame() restores frame->pc to original value in case function
graph tracer has modified a return address (LR) in a stack frame to hook
a function return. However, if function graph tracer has hit a filtered
function, then we can't unwind it as ftrace_push_return_trace() has
biased the index(frame->graph) with a 'huge negative'
offset(-FTRACE_NOTRACE_DEPTH).
Moreover, arm64 stack walker defines index(frame->graph) as unsigned
int, which can not compare a -ve number.
Similar problem we can have with calling of walk_stackframe() from
save_stack_trace_tsk() or dump_backtrace().
This patch fixes unwind_frame() to test the index for -ve value and
restore index accordingly before we can restore frame->pc.
If no monitoring feature is detected because all monitoring features are
disabled during boot time or there is no monitoring feature in hardware,
creating rdtgroup sub-directory by "mkdir" command reports error:
mkdir: cannot create directory ‘/sys/fs/resctrl/p1’: No such file or directory
But the sub-directory actually is generated and content is correct:
cpus cpus_list schemata tasks
The error is because rdtgroup_mkdir_ctrl_mon() returns non zero value after
the sub-directory is created and the returned value is reported as an error
to user.
Clear the returned value to report to user that the sub-directory is
actually created successfully.
Signed-off-by: Wang Hui <john.wanghui@huawei.com> Signed-off-by: Zhang Yanfei <yanfei.zhang@huawei.com> Signed-off-by: Fenghua Yu <fenghua.yu@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ravi V Shankar <ravi.v.shankar@intel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Cc: Vikas <vikas.shivappa@intel.com> Cc: Xiaochen Shen <xiaochen.shen@intel.com> Link: http://lkml.kernel.org/r/1519356363-133085-1-git-send-email-fenghua.yu@intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Similar to the ancient commit a5fe8e7695dc ("regulatory: add NUL
to alpha2"), add another byte to alpha2 in the request struct so
that when we use nla_put_string(), we don't overrun anything.
If an attempt is made to disable RX checksums, USB adapter is changed
but netdev->features is not, because smsc75xx_set_features() returns a
non zero value.
This throws errors from netdev_rx_csum_fault() :
<devname>: hw csum failure
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Steve Glendinning <steve.glendinning@shawell.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
nfs4_update_server unconditionally releases the nfs_client for the
source server. If migration fails, this can cause the source server's
nfs_client struct to be left with a low reference count, resulting in
use-after-free. Also, adjust reference count handling for ELOOP.
NFS: state manager: migration failed on NFSv4 server nfsvmu10 with error 6
WARNING: CPU: 16 PID: 17960 at fs/nfs/client.c:281 nfs_put_client+0xfa/0x110 [nfs]()
nfs_put_client+0xfa/0x110 [nfs]
nfs4_run_state_manager+0x30/0x40 [nfsv4]
kthread+0xd8/0xf0
dtc recently added PCI bus checks. Fix these warnings:
arch/arm64/boot/dts/cavium/thunder2-99xx.dtb: Warning (pci_bridge): Node /pci missing bus-range for PCI bridge
arch/arm64/boot/dts/cavium/thunder2-99xx.dtb: Warning (unit_address_vs_reg): Node /pci has a reg or ranges property, but no unit name
Signed-off-by: Rob Herring <robh@kernel.org> Cc: Jayachandran C <jnair@caviumnetworks.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If none of the certificates in a SignerInfo's certificate chain match a
trusted key, nor is the last certificate signed by a trusted key, then
pkcs7_validate_trust_one() tries to check whether the SignerInfo's
signature was made directly by a trusted key. But, it actually fails to
set the 'sig' variable correctly, so it actually verifies the last
signature seen. That will only be the SignerInfo's signature if the
certificate chain is empty; otherwise it will actually be the last
certificate's signature.
This is not by itself a security problem, since verifying any of the
certificates in the chain should be sufficient to verify the SignerInfo.
Still, it's not working as intended so it should be fixed.
Fix it by setting 'sig' correctly for the direct verification case.
Fixes: 757932e6da6d ("PKCS#7: Handle PKCS#7 messages that contain no X.509 certs") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
test_maps contains a series of stress tests, and previously it will break the
rest tests when it failed to alloc memory.
-----------------------
Failed to create hashmap key=8 value=262144 'Cannot allocate memory'
Failed to create hashmap key=16 value=262144 'Cannot allocate memory'
Failed to create hashmap key=8 value=262144 'Cannot allocate memory'
Failed to create hashmap key=8 value=262144 'Cannot allocate memory'
test_maps: test_maps.c:955: run_parallel: Assertion `status == 0' failed.
Aborted
not ok 1..3 selftests: test_maps [FAIL]
-----------------------
after this patch, the rest tests will be continue when it occurs an ENOMEM failure
CC: Alexei Starovoitov <alexei.starovoitov@gmail.com> CC: Philip Li <philip.li@intel.com> Suggested-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Li Zhijian <zhijianx.li@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When we terminate driver I/O (because we need to stop using a certain
channel path) we also need to ensure that a timer (which may have been
set up using ccw_device_start_timeout) is cleared.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When a timeout occurs for users of ccw_device_start_timeout
we will stop the IO and call the drivers int handler with
the irb pointer set to ERR_PTR(-ETIMEDOUT). Sometimes
however we'd set the irb pointer to ERR_PTR(-EIO) which is
not intended. Just set the correct value in all codepaths.
Reported-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There are cases a device driver can't start IO because the device is
currently in use by cio. In this case the device driver is notified
when the device is usable again.
Using ccw_device_start_timeout we would set the timeout (and change
an existing timeout) before we test for internal usage. Worst case
this could lead to an unexpected timer deletion.
Fix this by setting the timeout after we test for internal usage.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
I am using SECCOMP to filter syscalls on a ppc32 platform, and noticed
that the JIT compiler was failing on the BPF even though the
interpreter was working fine.
The issue was that the compiler was missing one of the instructions
used by SECCOMP, so here is a patch to enable JIT for that
instruction.
Fixes: eb84bab0fb38 ("ppc: Kconfig: Enable BPF JIT on ppc32") Signed-off-by: Mark Lord <mlord@pobox.com> Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If power domain information are missing in the device tree, no
power domains get initialized. However, imx_gpc_remove tries to
remove power domains always in the old DT binding case. Only
remove power domains when imx_gpc_probe initialized them in
first place.
Fixes: 721cabf6c660 ("soc: imx: move PGC handling to a new GPC driver") Signed-off-by: Stefan Agner <stefan@agner.ch> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Looking at functions with large stack frames across all architectures
led me discovering that BUG() suffers from the same problem as
fortify_panic(), which I've added a workaround for already.
In short, variables that go out of scope by calling a noreturn function
or __builtin_unreachable() keep using stack space in functions
afterwards.
A workaround that was identified is to insert an empty assembler
statement just before calling the function that doesn't return. I'm
adding a macro "barrier_before_unreachable()" to document this, and
insert calls to that in all instances of BUG() that currently suffer
from this problem.
The files that saw the largest change from this had these frame sizes
before, and much less with my patch:
fs/ext4/inode.c:82:1: warning: the frame size of 1672 bytes is larger than 800 bytes [-Wframe-larger-than=]
fs/ext4/namei.c:434:1: warning: the frame size of 904 bytes is larger than 800 bytes [-Wframe-larger-than=]
fs/ext4/super.c:2279:1: warning: the frame size of 1160 bytes is larger than 800 bytes [-Wframe-larger-than=]
fs/ext4/xattr.c:146:1: warning: the frame size of 1168 bytes is larger than 800 bytes [-Wframe-larger-than=]
fs/f2fs/inode.c:152:1: warning: the frame size of 1424 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_core.c:1195:1: warning: the frame size of 1068 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_core.c:395:1: warning: the frame size of 1084 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_ftp.c:298:1: warning: the frame size of 928 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_ftp.c:418:1: warning: the frame size of 908 bytes is larger than 800 bytes [-Wframe-larger-than=]
net/netfilter/ipvs/ip_vs_lblcr.c:718:1: warning: the frame size of 960 bytes is larger than 800 bytes [-Wframe-larger-than=]
drivers/net/xen-netback/netback.c:1500:1: warning: the frame size of 1088 bytes is larger than 800 bytes [-Wframe-larger-than=]
In case of ARC and CRIS, it turns out that the BUG() implementation
actually does return (or at least the compiler thinks it does),
resulting in lots of warnings about uninitialized variable use and
leaving noreturn functions, such as:
block/cfq-iosched.c: In function 'cfq_async_queue_prio':
block/cfq-iosched.c:3804:1: error: control reaches end of non-void function [-Werror=return-type]
include/linux/dmaengine.h: In function 'dma_maxpq':
include/linux/dmaengine.h:1123:1: error: control reaches end of non-void function [-Werror=return-type]
This makes them call __builtin_trap() instead, which should normally
dump the stack and kill the current process, like some of the other
architectures already do.
I tried adding barrier_before_unreachable() to panic() and
fortify_panic() as well, but that had very little effect, so I'm not
submitting that patch.
Vineet said:
: For ARC, it is double win.
:
: 1. Fixes 3 -Wreturn-type warnings
:
: | ../net/core/ethtool.c:311:1: warning: control reaches end of non-void function
: [-Wreturn-type]
: | ../kernel/sched/core.c:3246:1: warning: control reaches end of non-void function
: [-Wreturn-type]
: | ../include/linux/sunrpc/svc_xprt.h:180:1: warning: control reaches end of
: non-void function [-Wreturn-type]
:
: 2. bloat-o-meter reports code size improvements as gcc elides the
: generated code for stack return.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=82365 Link: http://lkml.kernel.org/r/20171219114112.939391-1-arnd@arndb.de Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Vineet Gupta <vgupta@synopsys.com> [arch/arc] Tested-by: Vineet Gupta <vgupta@synopsys.com> [arch/arc] Cc: Mikael Starvik <starvik@axis.com> Cc: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Christopher Li <sparse@chrisli.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Kees Cook <keescook@chromium.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Will Deacon <will.deacon@arm.com> Cc: "Steven Rostedt (VMware)" <rostedt@goodmis.org> Cc: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When configuring virtio_net to use the code path 'receive_small()',
in-order to get correct XDP_REDIRECT support, I discovered TCP packets
would get silently dropped when loading an XDP program action XDP_PASS.
The bug seems to be that receive_small() when XDP is loaded check that
hdr->hdr.flags is zero, which seems wrong as hdr.flags contains the
flags VIRTIO_NET_HDR_F_* :
#define VIRTIO_NET_HDR_F_NEEDS_CSUM 1 /* Use csum_start, csum_offset */
#define VIRTIO_NET_HDR_F_DATA_VALID 2 /* Csum is valid */
TCP got dropped as it had the VIRTIO_NET_HDR_F_DATA_VALID flag set.
The flags that are relevant here are the VIRTIO_NET_HDR_GSO_* flags
stored in hdr->hdr.gso_type. Thus, the fix is just check that none of
the gso_type flags have been set.
Fixes: bb91accf2733 ("virtio-net: XDP support for small buffers") Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
gcc warns about a possible overflow of the kmem_cache string, when adding
four characters to a string of the same length:
drivers/md/raid5.c: In function 'setup_conf':
drivers/md/raid5.c:2207:34: error: '-alt' directive writing 4 bytes into a region of size between 1 and 32 [-Werror=format-overflow=]
sprintf(conf->cache_name[1], "%s-alt", conf->cache_name[0]);
^~~~
drivers/md/raid5.c:2207:2: note: 'sprintf' output between 5 and 36 bytes into a destination of size 32
sprintf(conf->cache_name[1], "%s-alt", conf->cache_name[0]);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
If I'm counting correctly, we need 11 characters for the fixed part
of the string and 18 characters for a 64-bit pointer (when no gendisk
is used), so that leaves three characters for conf->level, which should
always be sufficient.
This makes the code use snprintf() with the correct length, to
make the code more robust against changes, and to get the compiler
to shut up.
In commit f4be6b43f1ac ("md/raid5: ensure we create a unique name for
kmem_cache when mddev has no gendisk") from 2010, Neil said that
the pointer could be removed "shortly" once devices without gendisk
are disallowed. I have no idea if that happened, but if it did, that
should probably be changed as well.
Continuing along with the fight against smp_read_barrier_depends() [1]
(or rather, against its improper use), add an unconditional barrier to
cmpxchg. This guarantees that dependency ordering is preserved when a
dependency is headed by an unsuccessful cmpxchg. As it turns out, the
change could enable further simplification of LKMM as proposed in [2].
During driver unload, the driver proceeds with cleanup
without waiting for the scheduled events. So the device
pointers get freed up and driver crashes when the events
are scheduled later.
Flush the bnxt_re_task work queue before starting
device removal.
The ID_AA64DFR0_EL1.PMUVer field doesn't follow the usual ID registers
scheme. While value 0xf indicates a non-architected PMU is implemented,
values 0x1 to 0xe indicate an increasingly featureful architected PMU,
as if the field were unsigned.
For more details, see ARM DDI 0487C.a, D10.1.4, "Alternative ID scheme
used for the Performance Monitors Extension version".
Currently, we treat the field as signed, and erroneously bail out for
values 0x8 to 0xe. Let's correct that.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Reviewed-by: Robin Murphy <robin.murphy@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The plane buffer address/stride/height was incorrectly updated in the
plane_atomic_update operation instead of the vsync irq.
This patch delays this operation in the vsync irq along with the
other plane delayed setup.
This issue was masked using legacy framebuffer and X11 modesetting, but
is clearly visible using gbm rendering when buffer is submitted late after
vblank, like using software decoding and OpenGL rendering in Kodi.
With this patch, tearing and other artifacts disappears completely.
Cc: Michal Lazo <michal.lazo@gmail.com> Fixes: bbbe775ec5b5 ("drm: Add support for Amlogic Meson Graphic Controller") Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/1518689976-23292-1-git-send-email-narmstrong@baylibre.com Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The exynos DRM driver uses real-time 'struct timeval' values
for exporting its timestamps to user space. This has multiple
problems:
1. signed seconds overflow in y2038
2. the 'struct timeval' definition is deprecated in the kernel
3. time may jump or go backwards after a 'settimeofday()' syscall
4. other DRM timestamps are in CLOCK_MONOTONIC domain, so they
can't be compared
5. exporting microseconds requires a division by 1000, which may
be slow on some architectures.
The code existed in two places before, but the IPP portion was
removed in 8ded59413ccc ("drm/exynos: ipp: Remove Exynos DRM
IPP subsystem"), so we no longer need to worry about it.
Ideally timestamps should just use 64-bit nanoseconds instead, but
of course we can't change that now. Instead, this tries to address
the first four points above by using monotonic 'timespec' values.
According to Tobias Jakobi, user space doesn't care about the
timestamp at the moment, so we can change the format. Even if
there is something looking at them, it will work just fine with
monotonic times as long as the application only looks at the
relative values between two events.
In the case of 'recover', an r10bio with R10BIO_WriteError &
R10BIO_IsRecover will be progressed by handle_write_completed().
This function traverses all r10bio->devs[copies].
If devs[m].repl_bio != NULL, it thinks conf->mirrors[dev].replacement
is also not NULL. However, this is not always true.
When there is an rdev of raid10 has replacement, then each r10bio
->devs[m].repl_bio != NULL in conf->r10buf_pool. However, in 'recover',
even if corresponded replacement is NULL, it doesn't clear r10bio
->devs[m].repl_bio, resulting in replacement NULL deference.
This bug was introduced when replacement support for raid10 was
added in Linux 3.3.
As NeilBrown suggested:
Elsewhere the determination of "is this device part of the
resync/recovery" is made by resting bio->bi_end_io.
If this is end_sync_write, then we tried to write here.
If it is NULL, then we didn't try to write.
In case an ADDBA request is received while there is already
an ongoing BA sessions with the same parameters, i.e., update
flow, an ADBBA response with decline status was sent twice. Fix it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Some APs include a non global operating class in their extended channel
switch information element. In such a case, as the operating class is not
known, mac80211 would decide to disconnect.
However the specification states that the operating class needs to be
taken from Annex E, but it does not specify from which table it should be
taken, so it is valid for an AP to use a non global operating class.
To avoid possibly unneeded disconnection, in such a case ignore the
operating class and assume that the current band is used, and if the
resulting channel and band configuration is invalid disconnect.
Signed-off-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When a low level driver calls cfg80211_disconnected(), wep keys are
not cleared. As a result, following connection requests will fail
since cfg80211 internal state shows a connection is still in progress.
Fix this by clearing the wep keys when disconnecting.
This ensures that mac80211 allocated management frames are properly
aligned, which makes copying them more efficient.
For instance, mt76 uses iowrite32_copy to copy beacon frames to beacon
template memory on the chip.
Misaligned 32-bit accesses cause CPU exceptions on MIPS and should be
avoided.
Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When xfrm_policy_get_afinfo returns NULL, it will not hold rcu
read lock. In this case, rcu_read_unlock should not be called
in xfrm_get_tos, just like other places where it's calling
xfrm_policy_get_afinfo.
Internal DASD device driver I/O such as query host access count or
path verification is started using the _sleep_on() function.
To mark a request as started or ended the callback_data is set to either
DASD_SLEEPON_START_TAG or DASD_SLEEPON_END_TAG.
In cases where the request has to be stopped unconditionally the status is
set to DASD_SLEEPON_END_TAG as well which leads to immediate clearing of
the request.
But the request might still be on a device request queue for normal
operation which might lead to a panic because of a BUG() statement in
__dasd_device_process_final_queue() or a list corruption of the device
request queue.
Fix by removing the setting of DASD_SLEEPON_END_TAG in the
dasd_cancel_req() and dasd_generic_requeue_all_requests() functions and
ensure that the request is not deleted in the requeue function.
Trigger the device tasklet in the requeue function and let the normal
processing cleanup the request.
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com> Reviewed-by: Jan Hoeppner <hoeppner@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If no metadata devices are configured on raid1/4/5/6/10
(e.g. via dm-raid), md_write_start() unconditionally waits
for superblocks to be written thus deadlocking.
Fix introduces mddev->has_superblocks bool, defines it in md_run()
and checks for it in md_write_start() to conditionally avoid waiting.
Once on it, check for non-existing superblocks in md_super_write().
Link: https://bugzilla.kernel.org/show_bug.cgi?id=198647 Fixes: cc27b0c78c796 ("md: fix deadlock between mddev_suspend() and md_write_start()") Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com> Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Due to a check recently added to copy_to_user(), it's now not permitted to
copy from slab-held data to userspace unless the slab is whitelisted. This
affects rxrpc_recvmsg() when it attempts to place an RXRPC_USER_CALL_ID
control message in the userspace control message buffer. A warning is
generated by usercopy_warn() because the source is the copy of the
user_call_ID retained in the rxrpc_call struct.
Work around the issue by copying the user_call_ID to a variable on the
stack and passing that to put_cmsg().
The tlv_len is u8, so we need to limit the size of the SDP URI. Enforce
this both in the NLA policy and in the code that performs the allocation
and copy, to avoid writing past the end of the allocated buffer.
Fixes: d9b8d8e19b073 ("NFC: llcp: Service Name Lookup netlink interface") Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In AP mode, when a new station associates, rs is initialized immediately
upon association completion, before the phy context is updated with the
association parameters, so the sta bandwidth might be wider than the phy
context allows.
To avoid this issue, always initialize rs with 20mhz bandwidth rate, and
after authorization, when the phy context is already up-to-date, re-init
rs with the correct bw.
In IBSS, the mac80211 sets the cab_queue to be invalid.
However, the multicast station uses it, so we need to override it.
A previous patch did it, but it was nested inside the if's and was
applied only for legacy FWs that don't support the new station type
API, instead of being applied for all paths.
In addition, add a missing NL80211_IFTYPE_ADHOC to the initialization
of the queues in iwl_mvm_mac_ctxt_init()
Fixes: ee48b72211f8 ("iwlwifi: mvm: support ibss in dqa mode") Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A previous patch allowed the same PN for packets originating from the
same AMSDU by copying PN only for the last packet in the series.
This however is bogus since we cannot assume the last frame will be
received on the same queue, and if it is received on a different ueue
we will end up not incrementing the PN and possibly let the next
packet to have the same PN and pass through.
Change the logic instead to driver explicitly indicate for the second
sub frame and on to be allowed to have the same PN as the first
subframe. Indicate it to mac80211 as well for the fallback queue.
Fixes: f1ae02b186d9 ("iwlwifi: mvm: allow same PN for de-aggregated AMSDU") Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Trying to boot an RK3328 box with an HS200-capable eMMC, I see said eMMC
fail to initialise as it can't run its tuning procedure, because the
sample clock is missing. Upon closer inspection, whilst the clock is
present in the DT, its name is subtly incorrect per the binding, so
__of_clk_get_by_name() never finds it. By inspection, the drive clock
suffers from a similar problem, so has never worked properly either.
This error has propagated across the 32-bit DTs too, so fix those up.
Trying to boot an RK3328 box with an HS200-capable eMMC, I see said eMMC
fail to initialise as it can't run its tuning procedure, because the
sample clock is missing. Upon closer inspection, whilst the clock is
present in the DT, its name is subtly incorrect per the binding, so
__of_clk_get_by_name() never finds it. By inspection, the drive clock
suffers from a similar problem, so has never worked properly either.
Fix up all instances of the incorrect clock names across the 64-bit DTs.
Fixes: d717f7352ec6 ("arm64: dts: rockchip: add sdmmc/sdio/emmc nodes for RK3328 SoCs") Fixes: b790c2cab5ca ("arm64: dts: add Rockchip rk3368 core dtsi and board dts for the r88 board") Signed-off-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If remove_commit fails then the lock is left locked while the uobj still
exists. Eventually the kernel will deadlock.
lockdep detects this and says:
test/4221 is leaving the kernel with locks still held!
1 lock held by test/4221:
#0: (&ucontext->cleanup_rwsem){.+.+}, at: [<000000001e5c7523>] rdma_explicit_destroy+0x37/0x120 [ib_uverbs]
Fixes: 4da70da23e9b ("IB/core: Explicitly destroy an object while keeping uobject") Signed-off-by: Leon Romanovsky <leon@kernel.org> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If the same attribute is listed twice by the user in the ioctl attribute
list then error unwind can cause the kernel to deref garbage.
This happens when an object with WRITE access is sent twice. The second
parse properly fails but corrupts the state required for the error unwind
it triggers.
Fixing this by making duplicates in the attribute list invalid. This is
not something we need to support.
The ioctl interface is currently recommended to be disabled in kConfig.
Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For AMD Promontory xHCI host, although you can disable USB ports in
BIOS settings, those ports will be enabled anyway after you remove a
device on that port and re-plug it in again. It's a known limitation of
the chip. As a workaround we can clear the PORT_WAKE_BITS.
[commit and code comment rephrasing -Mathias] Signed-off-by: Joe Lee <asmt.swfae@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When exposing data access through debugfs, the correct
debugfs_create_*() functions must be used, depending on data type.
Remove all casts from data pointers passed to debugfs_create_*()
functions, as such casts prevent the compiler from flagging bugs.
Correct all wrong usage:
- clk.rate is unsigned long, not u32,
- clk.flags is u8, not u32, which exposed the successive
clk.rate_offset and clk.src_offset fields.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
HS omaps use irq_save_secure_context() instead of irq_save_context()
so sar_base will never get initialized and irq_sar_clear() gets called
with a wrong address for HS omaps from irq_restore_context().
Starting with commit f4b9f40ae95b ("ARM: OMAP4+: Initialize SAR RAM
base early for proper CPU1 reset for kexec") we have it available,
and this ideally would been fixed with that commit already.
Fixes: f4b9f40ae95b ("ARM: OMAP4+: Initialize SAR RAM base early for
proper CPU1 reset for kexec") Cc: Andrew F. Davis <afd@ti.com> Cc: Dave Gerlach <d-gerlach@ti.com> Cc: Keerthy <j-keerthy@ti.com> Cc: Santosh Shilimkar <ssantosh@kernel.org> Cc: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For platform_suspend_ops, the finish call is too late to re-enable wake
irqs and we need re-enable wake irqs on wake call instead.
Otherwise noirq resume for devices has already happened. And then
dev_pm_disarm_wake_irq() has already disabled the dedicated wake irqs
when the interrupt triggers and the wake irq is never handled.
For devices that are already in PM runtime suspended state when we
enter suspend this means that a possible wake irq will never trigger.
And this can lead into a situation where a device has a pending padconf
wake irq, and the device will stay unresponsive to any further wake
irqs.
This issue can be easily reproduced by setting serial console log level
to zero, letting the serial console idle, and suspend the system from
an ssh terminal. Then try to wake up the system by typing to the serial
console.
Note that this affects only omap3 PRM interrupt as that's currently
the only omap variant that does anything in omap_pm_wake().
In general, for the wake irqs to work, the interrupt must have either
IRQF_NO_SUSPEND or IRQF_EARLY_RESUME set for it to trigger before
dev_pm_disarm_wake_irq() disables the wake irqs.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When more than one GP timers are used as kernel system timers and the
corresponding nodes in device-tree are marked with the same "disabled"
property, then the "attr" field of the property will be initialized
more than once as the property being added to sys file system via
__of_add_property_sysfs().
In __of_add_property_sysfs(), the "name" field of pp->attr.attr is set
directly to the return value of safe_name(), without taking care of
whether it's already a valid pointer to a memory block. If it is, its
old value will always be overwritten by the new one and the memory block
allocated before will a "ghost", then a kmemleak happened.
That the same "disabled" property being added to different nodes of device
tree would cause that kind of kmemleak overhead, at least once.
To fix it, allocate the property dynamically, and delete static one.
Based on patch: https://patchwork.kernel.org/patch/10042045/
arch64-linux-gnu-gcc -c sync.c -o sync/sync.o
sync.c:42:29: fatal error: linux/sync_file.h: No such file or directory
#include <linux/sync_file.h>
^
CFLAGS is not used during the compile step, so the system instead of
kernel headers are used. Fix this by adding CFLAGS to the OBJS compile
rule.
Reported-by: Lei Yang <Lei.Yang@windriver.com> Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org> Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This fixs the following comile warnings with ATA_DEBUG enabled,
which detected by Linaro GCC 5.2-2015.11:
drivers/ata/libata-scsi.c: In function 'ata_scsi_dump_cdb':
./include/linux/kern_levels.h:5:18: warning: format '%d' expects
argument of type 'int', but argument 6 has type 'u64 {aka long
long unsigned int}' [-Wformat=]
This commit enables thresh dma mode as this forces to disable checksuming,
and chooses delay values which make the interface stable.
These changes are needed, because ROCK64 is faced with two problems:
1. tx checksuming does not work with packets larger than 1498,
2. the default delays for tx/rx are not stable when using 1Gbps connection.
Delays were found out with:
https://github.com/ayufan-rock64/linux-build/tree/master/recipes/gmac-delays-test
Switch to use dividing to prevent integer overflow when size is too
big to calculate allocation size properly.
Reported-by: Eric Biggers <ebiggers3@gmail.com> Fixes: 6e6e41c31122 ("ptr_ring: fail early if queue occupies more than KMALLOC_MAX_SIZE") Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
'default N' should be 'default n', though they happen to have the same
effect here, due to undefined symbols (N in this case) evaluating to n
in a tristate sense.
Remove the default from ARC_EMUL_UNALIGNED instead of changing it. bool
and tristate symbols implicitly default to n.
Discovered with the
https://urldefense.proofpoint.com/v2/url?u=https-3A__github.com_ulfalizer_Kconfiglib_blob_master_examples_list-5Fundefined.py&d=DwIBAg&c=DPL6_X_6JkXFx7AXWqB0tg&r=c14YS-cH-kdhTOW89KozFhBtBJgs1zXscZojEZQ0THs&m=WxxD8ozR7QQUVzNCBksiznaisBGO_crN7PBOvAoju8s&s=1LmxsNqxwT-7wcInVpZ6Z1J27duZKSoyKxHIJclXU_M&e=
script.
mesh TTL offset in Mesh Channel Switch Parameters element depends on
not only Secondary Channel Offset element, but also affected by
HT Control field and Wide Bandwidth Channel Switch element.
So use element structure to manipulate mesh channel swich param IE
after removing its constant attribution to correct the miscalculation.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We now have a platform (Ranchu) in the "generic" platform which matches
based on the FDT compatible string using mips_machine_is_compatible(),
however that function doesn't stop at a blank struct
of_device_id::compatible as that is an array in the struct, not a
pointer to a string.
Fix the loop completion to check the first byte of the compatible array
rather than the address of the compatible array in the struct.
The recent LPM changes to setup_rfi_flush() are causing some section
mismatch warnings because we removed the __init annotation on
setup_rfi_flush():
The function setup_rfi_flush() references
the function __init ppc64_bolted_size().
the function __init memblock_alloc_base().
The references are actually in init_fallback_flush(), but that is
inlined into setup_rfi_flush().
These references are safe because:
- only pseries calls setup_rfi_flush() at runtime
- pseries always passes L1D_FLUSH_FALLBACK at boot
- so the fallback flush area will always be allocated
- so the check in init_fallback_flush() will always return early:
/* Only allocate the fallback flush area once (at boot time). */
if (l1d_flush_fallback_area)
return;
- and therefore we won't actually call the freed init routines.
We should rework the code to make it safer by default rather than
relying on the above, but for now as a quick-fix just add a __ref
annotation to squash the warning.
Fixes: abf110f3e1ce ("powerpc/rfi-flush: Make it possible to call setup_rfi_flush() again") Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
After migration the security feature flags might have changed (e.g.,
destination system with unpatched firmware), but some flags are not
set/clear again in init_cpu_char_feature_flags() because it assumes
the security flags to be the defaults.
Additionally, if the H_GET_CPU_CHARACTERISTICS hypercall fails then
init_cpu_char_feature_flags() does not run again, which potentially
might leave the system in an insecure or sub-optimal configuration.
So, just restore the security feature flags to the defaults assumed
by init_cpu_char_feature_flags() so it can set/clear them correctly,
and to ensure safe settings are in place in case the hypercall fail.
Fixes: f636c14790ea ("powerpc/pseries: Set or clear security feature flags")
Depends-on: 19887d6a28e2 ("powerpc: Move default security feature flags") Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The fallback RFI flush is used when firmware does not provide a way
to flush the cache. It's a "displacement flush" that evicts useful
data by displacing it with an uninteresting buffer.
The flush has to take care to work with implementation specific cache
replacment policies, so the recipe has been in flux. The initial
slow but conservative approach is to touch all lines of a congruence
class, with dependencies between each load. It has since been
determined that a linear pattern of loads without dependencies is
sufficient, and is significantly faster.
Measuring the speed of a null syscall with RFI fallback flush enabled
gives the relative improvement:
P8 - 1.83x
P9 - 1.75x
The flush also becomes simpler and more adaptable to different cache
geometries.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If there is a possibility that a VM may migrate to a Skylake host,
then the hypervisor should report IA32_ARCH_CAPABILITIES.RSBA[bit 2]
as being set (future work, of course). This implies that
CPUID.(EAX=7,ECX=0):EDX.ARCH_CAPABILITIES[bit 29] should be
set. Therefore, kvm should report this CPUID bit as being supported
whether or not the host supports it. Userspace is still free to clear
the bit if it chooses.
For more information on RSBA, see Intel's white paper, "Retpoline: A
Branch Target Injection Mitigation" (Document Number 337131-001),
currently available at https://bugzilla.kernel.org/show_bug.cgi?id=199511.
Since the IA32_ARCH_CAPABILITIES MSR is emulated in kvm, there is no
dependency on hardware support for this feature.
The CPUID bits of OSXSAVE (function=0x1) and OSPKE (func=0x7, leaf=0x0)
allows user apps to detect if OS has set CR4.OSXSAVE or CR4.PKE. KVM is
supposed to update these CPUID bits when CR4 is updated. Current KVM
code doesn't handle some special cases when updates come from emulator.
Here is one example:
Step 1: guest boots
Step 2: guest OS enables XSAVE ==> CR4.OSXSAVE=1 and CPUID.OSXSAVE=1
Step 3: guest hot reboot ==> QEMU reset CR4 to 0, but CPUID.OSXAVE==1
Step 4: guest os checks CPUID.OSXAVE, detects 1, then executes xgetbv
Step 4 above will cause an #UD and guest crash because guest OS hasn't
turned on OSXAVE yet. This patch solves the problem by comparing the the
old_cr4 with cr4. If the related bits have been changed,
kvm_update_cpuid() needs to be called.
Fix this by sanitizing *resource* before using it to index
current->signal->rlim
Notice that given that speculation windows are large, the policy is to
kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
KASAN uses different routines to map shadow for hot added memory and
memory obtained in boot process. Attempt to offline memory onlined by
normal boot process leads to this:
Trying to vfree() nonexistent vm area (000000005d3b34b9)
WARNING: CPU: 2 PID: 13215 at mm/vmalloc.c:1525 __vunmap+0x147/0x190
Obviously we can't call vfree() to free memory that wasn't allocated via
vmalloc(). Use find_vm_area() to see if we can call vfree().
Unfortunately it's a bit tricky to properly unmap and free shadow
allocated during boot, so we'll have to keep it. If memory will come
online again that shadow will be reused.
Matthew asked: how can you call vfree() on something that isn't a
vmalloc address?
vfree() is able to free any address returned by
__vmalloc_node_range(). And __vmalloc_node_range() gives you any
address you ask. It doesn't have to be an address in [VMALLOC_START,
VMALLOC_END] range.
That's also how the module_alloc()/module_memfree() works on
architectures that have designated area for modules.
[aryabinin@virtuozzo.com: improve comments] Link: http://lkml.kernel.org/r/dabee6ab-3a7a-51cd-3b86-5468718e0390@virtuozzo.com
[akpm@linux-foundation.org: fix typos, reflow comment] Link: http://lkml.kernel.org/r/20180201163349.8700-1-aryabinin@virtuozzo.com Fixes: fa69b5989bb0 ("mm/kasan: add support for memory hotplug") Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Reported-by: Paul Menzel <pmenzel+linux-kasan-dev@molgen.mpg.de> Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
shmat()'s SHM_REMAP option forbids passing a nil address for; this is in
fact the very first thing we check for. Andrea reported that for
SHM_RND|SHM_REMAP cases we can end up bypassing the initial addr check,
but we need to check again if the address was rounded down to nil. As
of this patch, such cases will return -EINVAL.
Link: http://lkml.kernel.org/r/20180503204934.kk63josdu6u53fbd@linux-n805 Signed-off-by: Davidlohr Bueso <dbueso@suse.de> Reported-by: Andrea Arcangeli <aarcange@redhat.com> Cc: Joe Lawrence <joe.lawrence@redhat.com> Cc: Manfred Spraul <manfred@colorfullife.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Patch series "ipc/shm: shmat() fixes around nil-page".
These patches fix two issues reported[1] a while back by Joe and Andrea
around how shmat(2) behaves with nil-page.
The first reverts a commit that it was incorrectly thought that mapping
nil-page (address=0) was a no no with MAP_FIXED. This is not the case,
with the exception of SHM_REMAP; which is address in the second patch.
I chose two patches because it is easier to backport and it explicitly
reverts bogus behaviour. Both patches ought to be in -stable and ltp
testcases need updated (the added testcase around the cve can be
modified to just test for SHM_RND|SHM_REMAP).
Commit 95e91b831f87 ("ipc/shm: Fix shmat mmap nil-page protection")
worked on the idea that we should not be mapping as root addr=0 and
MAP_FIXED. However, it was reported that this scenario is in fact
valid, thus making the patch both bogus and breaks userspace as well.
For example X11's libint10.so relies on shmat(1, SHM_RND) for lowmem
initialization[1].
[1] https://cgit.freedesktop.org/xorg/xserver/tree/hw/xfree86/os-support/linux/int10/linux.c#n347 Link: http://lkml.kernel.org/r/20180503203243.15045-2-dave@stgolabs.net Fixes: 95e91b831f87 ("ipc/shm: Fix shmat mmap nil-page protection") Signed-off-by: Davidlohr Bueso <dbueso@suse.de> Reported-by: Joe Lawrence <joe.lawrence@redhat.com> Reported-by: Andrea Arcangeli <aarcange@redhat.com> Cc: Manfred Spraul <manfred@colorfullife.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>