Xin Long [Sun, 26 Mar 2017 16:21:15 +0000 (00:21 +0800)]
sctp: change to save MSG_MORE flag into assoc
David Laight noticed the support for MSG_MORE with datamsg->force_delay
didn't really work as we expected, as the first msg with MSG_MORE set
would always block the following chunks' dequeuing.
This Patch is to rewrite it by saving the MSG_MORE flag into assoc as
David Laight suggested.
asoc->force_delay is used to save MSG_MORE flag before a msg is sent.
All chunks in queue would not be sent out if asoc->force_delay is set
by the msg with MSG_MORE flag, until a new msg without MSG_MORE flag
clears asoc->force_delay.
Note that this change would not affect the flush is generated by other
triggers, like asoc->state != ESTABLISHED, queue size > pmtu etc.
v1->v2:
Not clear asoc->force_delay after sending the msg with MSG_MORE flag.
Fixes: 4ea0c32f5f42 ("sctp: add support for MSG_MORE") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: David Laight <david.laight@aculab.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Rutland [Mon, 27 Mar 2017 17:00:14 +0000 (18:00 +0100)]
net: ipconfig: fix ic_close_devs() use-after-free
Our chosen ic_dev may be anywhere in our list of ic_devs, and we may
free it before attempting to close others. When we compare d->dev and
ic_dev->dev, we're potentially dereferencing memory returned to the
allocator. This causes KASAN to scream for each subsequent ic_dev we
check.
As there's a 1-1 mapping between ic_devs and netdevs, we can instead
compare d and ic_dev directly, which implicitly handles the !ic_dev
case, and avoids the use-after-free. The ic_dev pointer may be stale,
but we will not dereference it.
Original splat:
[ 6.487446] ==================================================================
[ 6.494693] BUG: KASAN: use-after-free in ic_close_devs+0xc4/0x154 at addr ffff800367efa708
[ 6.503013] Read of size 8 by task swapper/0/1
[ 6.507452] CPU: 5 PID: 1 Comm: swapper/0 Not tainted 4.11.0-rc3-00002-gda42158 #8
[ 6.514993] Hardware name: AppliedMicro Mustang/Mustang, BIOS 3.05.05-beta_rc Jan 27 2016
[ 6.523138] Call trace:
[ 6.525590] [<ffff200008094778>] dump_backtrace+0x0/0x570
[ 6.530976] [<ffff200008094d08>] show_stack+0x20/0x30
[ 6.536017] [<ffff200008bee928>] dump_stack+0x120/0x188
[ 6.541231] [<ffff20000856d5e4>] kasan_object_err+0x24/0xa0
[ 6.546790] [<ffff20000856d924>] kasan_report_error+0x244/0x738
[ 6.552695] [<ffff20000856dfec>] __asan_report_load8_noabort+0x54/0x80
[ 6.559204] [<ffff20000aae86ac>] ic_close_devs+0xc4/0x154
[ 6.564590] [<ffff20000aaedbac>] ip_auto_config+0x2ed4/0x2f1c
[ 6.570321] [<ffff200008084b04>] do_one_initcall+0xcc/0x370
[ 6.575882] [<ffff20000aa31de8>] kernel_init_freeable+0x5f8/0x6c4
[ 6.581959] [<ffff20000a16df00>] kernel_init+0x18/0x190
[ 6.587171] [<ffff200008084710>] ret_from_fork+0x10/0x40
[ 6.592468] Object at ffff800367efa700, in cache kmalloc-128 size: 128
[ 6.598969] Allocated:
[ 6.601324] PID = 1
[ 6.603427] save_stack_trace_tsk+0x0/0x418
[ 6.607603] save_stack_trace+0x20/0x30
[ 6.611430] kasan_kmalloc+0xd8/0x188
[ 6.615087] ip_auto_config+0x8c4/0x2f1c
[ 6.619002] do_one_initcall+0xcc/0x370
[ 6.622832] kernel_init_freeable+0x5f8/0x6c4
[ 6.627178] kernel_init+0x18/0x190
[ 6.630660] ret_from_fork+0x10/0x40
[ 6.634223] Freed:
[ 6.636233] PID = 1
[ 6.638334] save_stack_trace_tsk+0x0/0x418
[ 6.642510] save_stack_trace+0x20/0x30
[ 6.646337] kasan_slab_free+0x88/0x178
[ 6.650167] kfree+0xb8/0x478
[ 6.653131] ic_close_devs+0x130/0x154
[ 6.656875] ip_auto_config+0x2ed4/0x2f1c
[ 6.660875] do_one_initcall+0xcc/0x370
[ 6.664705] kernel_init_freeable+0x5f8/0x6c4
[ 6.669051] kernel_init+0x18/0x190
[ 6.672534] ret_from_fork+0x10/0x40
[ 6.676098] Memory state around the buggy address:
[ 6.680880] ffff800367efa600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 6.688078] ffff800367efa680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 6.695276] >ffff800367efa700: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 6.702469] ^
[ 6.705952] ffff800367efa780: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 6.713149] ffff800367efa800: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 6.720343] ==================================================================
[ 6.727536] Disabling lock debugging due to kernel taint
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: David S. Miller <davem@davemloft.net> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Cc: James Morris <jmorris@namei.org> Cc: Patrick McHardy <kaber@trash.net> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Fri, 24 Mar 2017 22:02:50 +0000 (23:02 +0100)]
net: hns: avoid gcc-7.0.1 warning for uninitialized data
hns_dsaf_set_mac_key() calls dsaf_set_field() on an uninitialized field,
which will then change only a few of its bits, causing a warning with
the latest gcc:
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_set_mac_uc_entry':
hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
(origin) &= (~(mask)); \
^~
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_set_mac_mc_entry':
hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_add_mac_mc_port':
hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_del_mac_entry':
hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_rm_mac_addr':
hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_del_mac_mc_port':
hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_get_mac_uc_entry':
hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_get_mac_mc_entry':
hisilicon/hns/hns_dsaf_reg.h:1046:12: error: 'mac_key.low.bits.port_vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The code is actually correct since we always set all 16 bits of the
port_vlan field, but gcc correctly points out that the first
access does contain uninitialized data.
This initializes the field to zero first before setting the
individual bits.
Fixes: 5483bfcb169c ("net: hns: modify tcam table and set mac key") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Fri, 24 Mar 2017 22:02:49 +0000 (23:02 +0100)]
net: hns: fix uninitialized data use
When dev_dbg() is enabled, we print uninitialized data, as gcc-7.0.1
now points out:
ethernet/hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_set_promisc_tcam':
ethernet/hisilicon/hns/hns_dsaf_main.c:2947:75: error: 'tbl_tcam_data.low.val' may be used uninitialized in this function [-Werror=maybe-uninitialized]
ethernet/hisilicon/hns/hns_dsaf_main.c:2947:75: error: 'tbl_tcam_data.high.val' may be used uninitialized in this function [-Werror=maybe-uninitialized]
We also pass the data into hns_dsaf_tcam_mc_cfg(), which might later
use it (not sure about that), so it seems safer to just always initialize
the tbl_tcam_data structure.
Fixes: 1f5fa2dd1cfa ("net: hns: fix for promisc mode in HNS driver") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
llvm can optimize the 'if (ptr > data_end)' checks to be in the order
slightly different than the original C code which will confuse verifier.
Like:
if (ptr + 16 > data_end)
return TC_ACT_SHOT;
// may be followed by
if (ptr + 14 > data_end)
return TC_ACT_SHOT;
while llvm can see that 'ptr' is valid for all 16 bytes,
the verifier could not.
Fix verifier logic to account for such case and add a test.
Reported-by: Huapeng Zhou <hzhou@fb.com> Fixes: 969bf05eb3ce ("bpf: direct packet access") Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
->disconnect() is not called with socket lock held.
Fix this by acquiring ping rwlock earlier.
Thanks to Daniel, Alexander and Andrey for letting us know this problem.
Fixes: c319b4d76b9e ("net: ipv4: add IPPROTO_ICMP socket kind") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Daniel Jiang <danieljiang0415@gmail.com> Reported-by: Solar Designer <solar@openwall.com> Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 24 Mar 2017 22:01:42 +0000 (15:01 -0700)]
i40e: Do not enable NAPI on q_vectors that have no rings
When testing the epoll w/ busy poll code I found that I could get into a
state where the i40e driver had q_vectors w/ active NAPI that had no rings.
This was resulting in a divide by zero error. To correct it I am updating
the driver code so that we only support NAPI on q_vectors that have 1 or
more rings allocated to them.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 24 Mar 2017 16:38:03 +0000 (09:38 -0700)]
net: Do not allow negative values for busy_read and busy_poll sysctl interfaces
This change basically codifies what I think was already the limitations on
the busy_poll and busy_read sysctl interfaces. We weren't checking the
lower bounds and as such could input negative values. The behavior when
that was used was dependent on the architecture. In order to prevent any
issues with that I am just disabling support for values less than 0 since
this way we don't have to worry about any odd behaviors.
By limiting the sysctl values this way it also makes it consistent with how
we handle the SO_BUSY_POLL socket option since the value appears to be
reported as a signed integer value and negative values are rejected.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
After additional regression testing, several users are experiencing
kernel panics during shutdown on e1000e devices. Reverting this
change resolves the issue.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Thu, 23 Mar 2017 18:03:31 +0000 (11:03 -0700)]
kcm: return immediately after copy_from_user() failure
There is no reason to continue after a copy_from_user()
failure.
Fixes: ab7ac4eb9832 ("kcm: Kernel Connection Multiplexor module") Cc: Tom Herbert <tom@herbertland.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Thu, 23 Mar 2017 16:07:26 +0000 (17:07 +0100)]
bna: avoid writing uninitialized data into hw registers
The latest gcc-7 snapshot warns about bfa_ioc_send_enable/bfa_ioc_send_disable
writing undefined values into the hardware registers:
drivers/net/ethernet/brocade/bna/bfa_ioc.c: In function 'bfa_iocpf_sm_disabling_entry':
arch/arm/include/asm/io.h:109:22: error: '*((void *)&disable_req+4)' is used uninitialized in this function [-Werror=uninitialized]
arch/arm/include/asm/io.h:109:22: error: '*((void *)&disable_req+8)' is used uninitialized in this function [-Werror=uninitialized]
The two functions look like they should do the same thing, but only one
of them initializes the time stamp and clscode field. The fact that we
only get a warning for one of the two functions seems to be arbitrary,
based on the inlining decisions in the compiler.
To address this, I'm making both functions do the same thing:
- set the clscode from the ioc structure in both
- set the time stamp from ktime_get_real_seconds (which also
avoids the signed-integer overflow in 2038 and extends the
well-defined behavior until 2106).
- zero-fill the reserved field
Fixes: 8b230ed8ec96 ("bna: Brocade 10Gb Ethernet device driver") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 24 Mar 2017 19:40:00 +0000 (12:40 -0700)]
Merge branch 's390-net'
Ursula Braun says:
====================
s390/qeth patches for net
here are 2 s390/qeth patches built for net fixing a problem with AF_IUCV
traffic through HiperSockets.
And we come up with an update for the MAINTAINERS file to establish
Julian as Co-Maintainer for drivers/s390/net and net/iucv.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 23 Mar 2017 13:55:09 +0000 (14:55 +0100)]
s390/qeth: no ETH header for outbound AF_IUCV
With AF_IUCV traffic, the skb passed to hard_start_xmit() has a 14 byte
slot at skb->data, intended for an ETH header. qeth_l3_fill_af_iucv_hdr()
fills this ETH header... and then immediately moves it to the
skb's headroom, where it disappears and is never seen again.
But it's still possible for us to return NETDEV_TX_BUSY after the skb has
been modified. Since we didn't get a private copy of the skb, the next
time the skb is delivered to hard_start_xmit() it no longer has the
expected layout (we moved the ETH header to the headroom, so skb->data
now starts at the IUCV_TRANS header). So when qeth_l3_fill_af_iucv_hdr()
does another round of rebuilding, the resulting qeth header ends up
all wrong. On transmission, the buffer is then rejected by
the HiperSockets device with SBALF15 = x'04'.
When this error is passed back to af_iucv as TX_NOTIFY_UNREACHABLE, it
tears down the offending socket.
As the ETH header for AF_IUCV serves no purpose, just align the code to
what we do for IP traffic on L3 HiperSockets: keep the ETH header at
skb->data, and pass down data_offset = ETH_HLEN to qeth_fill_buffer().
When mapping the payload into the SBAL elements, the ETH header is then
stripped off. This avoids the skb manipulations in
qeth_l3_fill_af_iucv_hdr(), and any buffer re-entering hard_start_xmit()
after NETDEV_TX_BUSY is now processed properly.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 23 Mar 2017 13:55:08 +0000 (14:55 +0100)]
s390/qeth: size calculation outbound buffers
Depending on the device type, hard_start_xmit() builds different output
buffer formats. For instance with HiperSockets, on both L2 and L3 we
strip the ETH header from the skb - L3 doesn't need it, and L2 carries
it in the buffer's header element.
For this, we pass data_offset = ETH_HLEN all the way down to
__qeth_fill_buffer(), where skb->data is then adjusted accordingly.
But the initial size calculation still considers the *full* skb length
(including the ETH header). So qeth_get_elements_no() can erroneously
reject a skb as too big, even though it would actually fit into an
output buffer once the ETH header has been trimmed off later.
Fix this by passing an additional offset to qeth_get_elements_no(),
that indicates where in the skb the on-wire data actually begins.
Since the current code uses data_offset=-1 for some special handling
on OSA, we need to clamp data_offset to 0...
On HiperSockets this helps when sending ~MTU-size skbs with weird page
alignment. No change for OSA or AF_IUCV.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fix for missing initialization aq_ring header.lock spinlock.
Fixes: 018423e90bee ("net: ethernet: aquantia: Add ring support code") Signed-off-by: Pavel Belous <pavel.belous@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Belous [Thu, 23 Mar 2017 11:19:42 +0000 (14:19 +0300)]
net:ethernet:aquantia: Fix packet type detection (TCP/UDP) for IPv6.
In order for the checksum offloads to work correctly we need to set the
packet type bit (TCP/UDP) in the TX context buffer.
Fixes: 97bde5c4f909 ("net: ethernet: aquantia: Support for NIC-specific code") Signed-off-by: Pavel Belous <pavel.belous@aquantia.com> Tested-by: David Arcari <darcari@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Belous [Thu, 23 Mar 2017 11:19:41 +0000 (14:19 +0300)]
net:ethernet:aquantia: Remove adapter re-opening when MTU changed.
Closing/opening the adapter is not needed at all.
The new MTU settings take effect immediately.
Fixes: 97bde5c4f909 ("net: ethernet: aquantia: Support for NIC-specific code") Signed-off-by: Pavel Belous <pavel.belous@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
hayeswang [Thu, 23 Mar 2017 11:14:19 +0000 (19:14 +0800)]
r8152: prevent the driver from transmitting packets with carrier off
The linking status may be changed when autosuspend. And, after
autoresume, the driver may try to transmit packets when the device
is carrier off, because the interrupt transfer doesn't update the
linking status, yet. And, if the device is in ALDPS mode, the device
would stop working.
The another similar case is
1. unplug the cable.
2. interrupt transfer queue a work_queue for linking change.
3. device enters the ALDPS mode.
4. a tx occurs before the work_queue is called.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Sullivan [Wed, 22 Mar 2017 20:27:01 +0000 (15:27 -0500)]
net: phy: handle state correctly in phy_stop_machine
If the PHY is halted on stop, then do not set the state to PHY_UP. This
ensures the phy will be restarted later in phy_start when the machine is
started again.
Fixes: 00db8189d984 ("This patch adds a PHY Abstraction Layer to the Linux Kernel, enabling ethernet drivers to remain as ignorant as is reasonable of the connected PHY's design and operation details.") Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com> Signed-off-by: Brad Mouring <brad.mouring@ni.com> Acked-by: Xander Huff <xander.huff@ni.com> Acked-by: Kyle Roeschley <kyle.roeschley@ni.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 23 Mar 2017 19:39:21 +0000 (12:39 -0700)]
net: neigh: guard against NULL solicit() method
Dmitry posted a nice reproducer of a bug triggering in neigh_probe()
when dereferencing a NULL neigh->ops->solicit method.
This can happen for arp_direct_ops/ndisc_direct_ops and similar,
which can be used for NUD_NOARP neighbours (created when dev->header_ops
is NULL). Admin can then force changing nud_state to some other state
that would fire neigh timer.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 23 Mar 2017 05:40:30 +0000 (22:40 -0700)]
net: phy: Export mdiobus_register_board_info()
We can build modular code that uses mdiobus_register_board_info() which would
lead to linking failure since this symbol is not expoerted.
Fixes: 648ea0134069 ("net: phy: Allow pre-declaration of MDIO devices") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 23 Mar 2017 18:58:08 +0000 (11:58 -0700)]
Merge tag 'sound-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains the collection of small fixes for 4.11 that were pending
during my vacation:
- a few HD-audio quirks (more Dell headset support, docking station
support on HP laptops)
- a regression fix for the previous ctxfi DMA mask fix
- a correction of the new CONFIG_SND_X86 menu entry
- a fix for the races in ALSA sequencer core spotted by syzkaller"
* tag 'sound-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Adding a group of pin definition to fix headset problem
ALSA: seq: Fix racy cell insertions during snd_seq_pool_done()
ALSA: x86: Make CONFIG_SND_X86 bool
ALSA: hda - add support for docking station for HP 840 G3
ALSA: hda - add support for docking station for HP 820 G2
ALSA: ctxfi: Fix the incorrect check of dma_set_mask() call
Linus Torvalds [Thu, 23 Mar 2017 18:39:33 +0000 (11:39 -0700)]
Merge branch 'for-linus-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"Zygo tracked down a very old bug with inline compressed extents.
I didn't tag this one for stable because I want to do individual
tested backports. It's a little tricky and I'd rather do some extra
testing on it along the way"
* 'for-linus-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: add missing memset while reading compressed inline extents
Btrfs: fix regression in lock_delalloc_pages
btrfs: remove btrfs_err_str function from uapi/linux/btrfs.h
1) Several netfilter fixes from Pablo and the crew:
- Handle fragmented packets properly in netfilter conntrack, from
Florian Westphal.
- Fix SCTP ICMP packet handling, from Ying Xue.
- Fix big-endian bug in nftables, from Liping Zhang.
- Fix alignment of fake conntrack entry, from Steven Rostedt.
2) Fix feature flags setting in fjes driver, from Taku Izumi.
3) Openvswitch ipv6 tunnel source address not set properly, from Or
Gerlitz.
4) Fix jumbo MTU handling in amd-xgbe driver, from Thomas Lendacky.
5) sk->sk_frag.page not released properly in some cases, from Eric
Dumazet.
6) Fix RTNL deadlocks in nl80211, from Johannes Berg.
7) Fix erroneous RTNL lockdep splat in crypto, from Herbert Xu.
8) Cure improper inflight handling during AF_UNIX GC, from Andrey
Ulanov.
9) sch_dsmark doesn't write to packet headers properly, from Eric
Dumazet.
10) Fix SCM_TIMESTAMPING_OPT_STATS handling in TCP, from Soheil Hassas
Yeganeh.
11) Add some IDs for Motorola qmi_wwan chips, from Tony Lindgren.
12) Fix nametbl deadlock in tipc, from Ying Xue.
13) GRO and LRO packets not counted correctly in mlx5 driver, from Gal
Pressman.
14) Fix reset of internal PHYs in bcmgenet, from Doug Berger.
15) Fix hashmap allocation handling, from Alexei Starovoitov.
16) nl_fib_input() needs stronger netlink message length checking, from
Eric Dumazet.
17) Fix double-free of sk->sk_filter during sock clone, from Daniel
Borkmann.
18) Fix RX checksum offloading in aquantia driver, from Pavel Belous.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (85 commits)
net:ethernet:aquantia: Fix for RX checksum offload.
amd-xgbe: Fix the ECC-related bit position definitions
sfc: cleanup a condition in efx_udp_tunnel_del()
Bluetooth: btqcomsmd: fix compile-test dependency
inet: frag: release spinlock before calling icmp_send()
tcp: initialize icsk_ack.lrcvtime at session start time
genetlink: fix counting regression on ctrl_dumpfamily()
socket, bpf: fix sk_filter use after free in sk_clone_lock
ipv4: provide stronger user input validation in nl_fib_input()
bpf: fix hashmap extra_elems logic
enic: update enic maintainers
net: bcmgenet: remove bcmgenet_internal_phy_setup()
ipv6: make sure to initialize sockc.tsflags before first use
fjes: Do not load fjes driver if extended socket device is not power on.
fjes: Do not load fjes driver if system does not have extended socket device.
net/mlx5e: Count LRO packets correctly
net/mlx5e: Count GSO packets correctly
net/mlx5: Increase number of max QPs in default profile
net/mlx5e: Avoid supporting udp tunnel port ndo for VF reps
net/mlx5e: Use the proper UAPI values when offloading TC vlan actions
...
Hui Wang [Thu, 23 Mar 2017 02:00:25 +0000 (10:00 +0800)]
ALSA: hda - Adding a group of pin definition to fix headset problem
A new Dell laptop needs to apply ALC269_FIXUP_DELL1_MIC_NO_PRESENCE to
fix the headset problem, and the pin definiton of this machine is not
in the pin quirk table yet, now adding it to the table.
Signed-off-by: Hui Wang <hui.wang@canonical.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lendacky, Thomas [Wed, 22 Mar 2017 22:25:27 +0000 (17:25 -0500)]
amd-xgbe: Fix the ECC-related bit position definitions
The ECC bit positions that describe whether the ECC interrupt is for
Tx, Rx or descriptor memory and whether the it is a single correctable
or double detected error were defined in incorrectly (reversed order).
Fix the bit position definitions for these settings so that the proper
ECC handling is performed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 22 Mar 2017 09:10:02 +0000 (12:10 +0300)]
sfc: cleanup a condition in efx_udp_tunnel_del()
Presumably if there is an "add" function, there is also a "del"
function. But it causes a static checker warning because it looks like
a common cut and paste bug.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Mon, 20 Mar 2017 22:31:10 +0000 (15:31 -0700)]
Bluetooth: btqcomsmd: fix compile-test dependency
compile-testing fails when QCOM_SMD is a loadable module:
drivers/bluetooth/built-in.o: In function `btqcomsmd_send':
btqca.c:(.text+0xa8): undefined reference to `qcom_smd_send'
drivers/bluetooth/built-in.o: In function `btqcomsmd_probe':
btqca.c:(.text+0x3ec): undefined reference to `qcom_wcnss_open_channel'
btqca.c:(.text+0x46c): undefined reference to `qcom_smd_set_drvdata'
This clarifies the dependency to allow compile-testing only when
SMD is completely disabled, otherwise the dependency on QCOM_SMD
will make sure we can link against it.
Fixes: e27ee2b16bad ("Bluetooth: btqcomsmd: Allow driver to build if COMPILE_TEST is enabled") Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[bjorn: Restructure and clarify dependency to QCOM_WCNSS_CTRL] Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: David S. Miller <davem@davemloft.net>
genetlink: fix counting regression on ctrl_dumpfamily()
Commit 2ae0f17df1cd ("genetlink: use idr to track families") replaced
if (++n < fams_to_skip)
continue;
into:
if (n++ < fams_to_skip)
continue;
This subtle change cause that on retry ctrl_dumpfamily() call we omit
one family that failed to do ctrl_fill_info() on previous call, because
cb->args[0] = n number counts also family that failed to do
ctrl_fill_info().
Patch fixes the problem and avoid confusion in the future just decrease
n counter when ctrl_fill_info() fail.
User visible problem caused by this bug is failure to get access to
some genetlink family i.e. nl80211. However problem is reproducible
only if number of registered genetlink families is big enough to
cause second call of ctrl_dumpfamily().
Cc: Xose Vazquez Perez <xose.vazquez@gmail.com> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: Johannes Berg <johannes@sipsolutions.net> Fixes: 2ae0f17df1cd ("genetlink: use idr to track families") Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 22 Mar 2017 12:08:08 +0000 (13:08 +0100)]
socket, bpf: fix sk_filter use after free in sk_clone_lock
In sk_clone_lock(), we create a new socket and inherit most of the
parent's members via sock_copy() which memcpy()'s various sections.
Now, in case the parent socket had a BPF socket filter attached,
then newsk->sk_filter points to the same instance as the original
sk->sk_filter.
sk_filter_charge() is then called on the newsk->sk_filter to take a
reference and should that fail due to hitting max optmem, we bail
out and release the newsk instance.
The issue is that commit 278571baca2a ("net: filter: simplify socket
charging") wrongly combined the dismantle path with the failure path
of xfrm_sk_clone_policy(). This means, even when charging failed, we
call sk_free_unlock_clone() on the newsk, which then still points to
the same sk_filter as the original sk.
Thus, sk_free_unlock_clone() calls into __sk_destruct() eventually
where it tests for present sk_filter and calls sk_filter_uncharge()
on it, which potentially lets sk_omem_alloc wrap around and releases
the eBPF prog and sk_filter structure from the (still intact) parent.
Fix it by making sure that when sk_filter_charge() failed, we reset
newsk->sk_filter back to NULL before passing to sk_free_unlock_clone(),
so that we don't mess with the parents sk_filter.
Only if xfrm_sk_clone_policy() fails, we did reach the point where
either the parent's filter was NULL and as a result newsk's as well
or where we previously had a successful sk_filter_charge(), thus for
that case, we do need sk_filter_uncharge() to release the prior taken
reference on sk_filter.
Fixes: 278571baca2a ("net: filter: simplify socket charging") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 22 Mar 2017 02:22:28 +0000 (19:22 -0700)]
ipv4: provide stronger user input validation in nl_fib_input()
Alexander reported a KMSAN splat caused by reads of uninitialized
field (tb_id_in) from user provided struct fib_result_nl
It turns out nl_fib_input() sanity tests on user input is a bit
wrong :
User can pretend nlh->nlmsg_len is big enough, but provide
at sendmsg() time a too small buffer.
Reported-by: Alexander Potapenko <glider@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In both kmalloc and prealloc mode the bpf_map_update_elem() is using
per-cpu extra_elems to do atomic update when the map is full.
There are two issues with it. The logic can be misused, since it allows
max_entries+num_cpus elements to be present in the map. And alloc_extra_elems()
at map creation time can fail percpu alloc for large map values with a warn:
WARNING: CPU: 3 PID: 2752 at ../mm/percpu.c:892 pcpu_alloc+0x119/0xa60
illegal size (32824) or align (8) for percpu allocation
The fixes for both of these issues are different for kmalloc and prealloc modes.
For prealloc mode allocate extra num_possible_cpus elements and store
their pointers into extra_elems array instead of actual elements.
Hence we can use these hidden(spare) elements not only when the map is full
but during bpf_map_update_elem() that replaces existing element too.
That also improves performance, since pcpu_freelist_pop/push is avoided.
Unfortunately this approach cannot be used for kmalloc mode which needs
to kfree elements after rcu grace period. Therefore switch it back to normal
kmalloc even when full and old element exists like it was prior to
commit 6c9059817432 ("bpf: pre-allocate hash map elements").
Add tests to check for over max_entries and large map values.
Reported-by: Dave Jones <davej@codemonkey.org.uk> Fixes: 6c9059817432 ("bpf: pre-allocate hash map elements") Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6ac3ce8295e6 ("net: bcmgenet: Remove excessive PHY reset")
removed the bcmgenet_mii_reset() function from bcmgenet_power_up() and
bcmgenet_internal_phy_setup() functions. In so doing it broke the reset
of the internal PHY devices used by the GENETv1-GENETv3 which required
this reset before the UniMAC was enabled. It also broke the internal
GPHY devices used by the GENETv4 because the config_init that installed
the AFE workaround was no longer occurring after the reset of the GPHY
performed by bcmgenet_phy_power_set() in bcmgenet_internal_phy_setup().
In addition the code in bcmgenet_internal_phy_setup() related to the
"enable APD" comment goes with the bcmgenet_mii_reset() so it should
have also been removed.
Commit bd4060a6108b ("net: bcmgenet: Power on integrated GPHY in
bcmgenet_power_up()") moved the bcmgenet_phy_power_set() call to the
bcmgenet_power_up() function, but failed to remove it from the
bcmgenet_internal_phy_setup() function. Had it done so, the
bcmgenet_internal_phy_setup() function would have been empty and could
have been removed at that time.
Commit 5dbebbb44a6a ("net: bcmgenet: Software reset EPHY after power on")
was submitted to correct the functional problems introduced by
commit 6ac3ce8295e6 ("net: bcmgenet: Remove excessive PHY reset"). It
was included in v4.4 and made available on 4.3-stable. Unfortunately,
it didn't fully revert the commit because this bcmgenet_mii_reset()
doesn't apply the soft reset to the internal GPHY used by GENETv4 like
the previous one did. This prevents the restoration of the AFE work-
arounds for internal GPHY devices after the bcmgenet_phy_power_set() in
bcmgenet_internal_phy_setup().
This commit takes the alternate approach of removing the unnecessary
bcmgenet_internal_phy_setup() function which shouldn't have been in v4.3
so that when bcmgenet_mii_reset() was restored it should have only gone
into bcmgenet_power_up(). This will avoid the problems while also
removing the redundancy (and hopefully some of the confusion).
Fixes: 6ac3ce8295e6 ("net: bcmgenet: Remove excessive PHY reset") Signed-off-by: Doug Berger <opendmb@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6: make sure to initialize sockc.tsflags before first use
In the case udp_sk(sk)->pending is AF_INET6, udpv6_sendmsg() would
jump to do_append_data, skipping the initialization of sockc.tsflags.
Fix the problem by moving sockc.tsflags initialization earlier.
The bug was detected with KMSAN.
Fixes: c14ac9451c34 ("sock: enable timestamping using control messages") Signed-off-by: Alexander Potapenko <glider@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 22 Mar 2017 19:38:17 +0000 (12:38 -0700)]
Merge branch 'fjes-fixes'
YASUAKI ISHIMATSU says:
====================
fjes: Do not load fjes driver
The fjes driver is used only by FUJITSU servers and almost of all
servers in the world never use it. But currently if ACPI PNP0C02
is defined in the ACPI table, the following message is always shown:
fjes: Do not load fjes driver if extended socket device is not power on.
The extended device socket cannot turn on/off while system is running.
So when system boots up and the device is not power on, the fjes driver
does not need be loaded.
To check the status of the device, the patch adds ACPI _STA method check.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> CC: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
fjes: Do not load fjes driver if system does not have extended socket device.
The fjes driver is used only by FUJITSU servers and almost of all
servers in the world never use it. But currently if ACPI PNP0C02
is defined in the ACPI table, the following message is always shown:
The message makes users confused because there is no reason that
the message is shown in other vendor servers.
To avoid the confusion, the patch adds a check that the server
has a extended socket device or not.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> CC: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gal Pressman [Tue, 21 Mar 2017 13:59:19 +0000 (15:59 +0200)]
net/mlx5e: Count LRO packets correctly
RX packets statistics ('rx_packets' counter) used to count LRO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.
Note that no information is lost in this patch due to 'rx_lro_packets'
counter existence.
Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets"
rx_packets: 1935066
rx_lro_packets: 35847
rx_packets_phy: 1935066
Fixes: e586b3b0baee ("net/mlx5: Ethernet Datapath files") Signed-off-by: Gal Pressman <galp@mellanox.com> Cc: kernel-team@fb.com Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Gal Pressman [Tue, 21 Mar 2017 13:59:18 +0000 (15:59 +0200)]
net/mlx5e: Count GSO packets correctly
TX packets statistics ('tx_packets' counter) used to count GSO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.
Note that no information is lost in this patch due to 'tx_tso_packets'
counter existence.
Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets"
tx_packets: 2451115
tx_tso_packets: 60954
tx_packets_phy: 2451115
Fixes: e586b3b0baee ("net/mlx5: Ethernet Datapath files") Signed-off-by: Gal Pressman <galp@mellanox.com> Cc: kernel-team@fb.com Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Maor Gottlieb [Tue, 21 Mar 2017 13:59:17 +0000 (15:59 +0200)]
net/mlx5: Increase number of max QPs in default profile
With ConnectX-4 sharing SRQs from the same space as QPs, we hit a
limit preventing some applications to allocate needed QPs amount.
Double the size to 256K.
Fixes: e126ba97dba9e ('mlx5: Add driver for Mellanox Connect-IB adapters') Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Blakey [Tue, 21 Mar 2017 13:59:16 +0000 (15:59 +0200)]
net/mlx5e: Avoid supporting udp tunnel port ndo for VF reps
This was added to allow the TC offloading code to identify offloading
encap/decap vxlan rules.
The VF reps are effectively related to the same mlx5 PCI device as the
PF. Since the kernel invokes the (say) delete ndo for each netdev, the
FW erred on multiple vxlan dst port deletes when the port was deleted
from the system.
We fix that by keeping the registration to be carried out only by the
PF. Since the PF serves as the uplink device, the VF reps will look
up a port there and realize if they are ok to offload that.
Tested:
<SETUP VFS>
<SETUP switchdev mode to have representors>
ip link add vxlan1 type vxlan id 44 dev ens5f0 dstport 9999
ip link set vxlan1 up
ip link del dev vxlan1
Fixes: 4a25730eb202 ('net/mlx5e: Add ndo_udp_tunnel_add to VF representors') Signed-off-by: Paul Blakey <paulb@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Roi Dayan [Tue, 21 Mar 2017 13:59:14 +0000 (15:59 +0200)]
net/mlx5: E-Switch, Don't allow changing inline mode when flows are configured
Changing the eswitch inline mode can potentially cause already configured
flows not to match the policy. E.g. set policy L4, add some L4 rules,
set policy to L2 --> bad! Hence we disallow it.
Keep track of how many offloaded rules are now set and refuse
inline mode changes if this isn't zero.
Fixes: bffaa916588e ("net/mlx5: E-Switch, Add control for inline mode") Signed-off-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Tue, 21 Mar 2017 13:59:13 +0000 (15:59 +0200)]
net/mlx5e: Change the TC offload rule add/del code path to be per NIC or E-Switch
Refactor the code to deal with add/del TC rules to have handler per NIC/E-switch
offloading use case, and push the latter into the e-switch code. This provides
better separation and is to be used in down-stream patch for applying a fix.
Fixes: bffaa916588e ("net/mlx5: E-Switch, Add control for inline mode") Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Tue, 21 Mar 2017 13:59:12 +0000 (15:59 +0200)]
net/mlx5: Add missing entries for set/query rate limit commands
The switch cases for the rate limit set and query commands were
missing, which could get us wrong under fw error or driver reset
flow, fix that.
Fixes: 1466cc5b23d1 ('net/mlx5: Rate limit tables support') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 22 Mar 2017 19:06:49 +0000 (12:06 -0700)]
Merge tag 'wireless-drivers-for-davem-2017-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.11
iwlwifi
* fix a user reported warning in DQA
mwifiex
* fix a potential double free
* fix lost early debug logs
* fix init wakeup warning message from device framework
* add Ganapathi and Xinming as maintainers
ath10k
* fix regression with QCA6174 during resume and firmware crash
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ying Xue [Tue, 21 Mar 2017 09:47:49 +0000 (10:47 +0100)]
tipc: fix nametbl deadlock at tipc_nametbl_unsubscribe
Until now, tipc_nametbl_unsubscribe() is called at subscriptions
reference count cleanup. Usually the subscriptions cleanup is
called at subscription timeout or at subscription cancel or at
subscriber delete.
We have ignored the possibility of this being called from other
locations, which causes deadlock as we try to grab the
tn->nametbl_lock while holding it already.
Xin Long [Mon, 20 Mar 2017 09:46:27 +0000 (17:46 +0800)]
sctp: declare struct sctp_stream before using it
sctp_stream_free uses struct sctp_stream as a param, but struct sctp_stream
is defined after it's declaration.
This patch is to declare struct sctp_stream before sctp_stream_free.
Fixes: a83863174a61 ("sctp: prepare asoc stream for stream reconf") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Mon, 20 Mar 2017 08:58:33 +0000 (09:58 +0100)]
cpsw/netcp: cpts depends on posix_timers
With posix timers having become optional, we get a build error with
the cpts time sync option of the CPSW driver:
drivers/net/ethernet/ti/cpts.c: In function 'cpts_find_ts':
drivers/net/ethernet/ti/cpts.c:291:23: error: implicit declaration of function 'ptp_classify_raw';did you mean 'ptp_classifier_init'? [-Werror=implicit-function-declaration]
This adds a hard dependency on PTP_CLOCK to avoid the problem, as
building it without PTP support makes no sense anyway.
Fixes: baa73d9e478f ("posix-timers: Make them configurable") Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: stable@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Mon, 20 Mar 2017 08:52:50 +0000 (09:52 +0100)]
cpsw/netcp: work around reverse cpts dependency
The dependency is reversed: cpsw and netcp call into cpts,
but cpts depends on the other two in Kconfig. This can lead
to cpts being a loadable module and its callers built-in:
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_remove':
cpsw.c:(.text.cpsw_remove+0xd0): undefined reference to `cpts_release'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_rx_handler':
cpsw.c:(.text.cpsw_rx_handler+0x2dc): undefined reference to `cpts_rx_timestamp'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_tx_handler':
cpsw.c:(.text.cpsw_tx_handler+0x7c): undefined reference to `cpts_tx_timestamp'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_ndo_stop':
As a workaround, I'm introducing another Kconfig symbol to
control the compilation of cpts, while making the actual
module controlled by a silent symbol that is =y when necessary.
Fixes: 6246168b4a38 ("net: ethernet: ti: netcp: add support of cpts") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 22 Mar 2017 17:50:37 +0000 (10:50 -0700)]
Merge branch 'r8152-rx-settings'
Hayes Wang says:
====================
r8152: fix the rx settings of RTL8153
The RMS and the rx early size should base on the same rx size. However,
the RMS is set to 9K bytes now and the rx early depends on mtu. For using
the rx buffer effectively, sync the two settings according to the mtu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
hayeswang [Mon, 20 Mar 2017 08:13:44 +0000 (16:13 +0800)]
r8152: set the RMS of RTL8153 according to the mtu
Set the received maximum size (RMS) according to the mtu size. It is
unnecessary to receive a packet which is more than the size we could
transmit. Besides, this could let the rx buffer be used effectively.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tejun Heo [Tue, 14 Mar 2017 23:25:56 +0000 (19:25 -0400)]
cgroup, net_cls: iterate the fds of only the tasks which are being migrated
The net_cls controller controls the classid field of each socket which
is associated with the cgroup. Because the classid is per-socket
attribute, when a task migrates to another cgroup or the configured
classid of the cgroup changes, the controller needs to walk all
sockets and update the classid value, which was implemented by 3b13758f51de ("cgroups: Allow dynamically changing net_classid").
While the approach is not scalable, migrating tasks which have a lot
of fds attached to them is rare and the cost is born by the ones
initiating the operations. However, for simplicity, both the
migration and classid config change paths call update_classid() which
scans all fds of all tasks in the target css. This is an overkill for
the migration path which only needs to cover a much smaller subset of
tasks which are actually getting migrated in.
On cgroup v1, this can lead to unexpected scalability issues when one
tries to migrate a task or process into a net_cls cgroup which already
contains a lot of fds. Even if the migration traget doesn't have many
to get scanned, update_classid() ends up scanning all fds in the
target cgroup which can be extremely numerous.
Unfortunately, on cgroup v2 which doesn't use net_cls, the problem is
even worse. Before bfc2cf6f61fc ("cgroup: call subsys->*attach() only
for subsystems which are actually affected by migration"), cgroup core
would call the ->css_attach callback even for controllers which don't
see actual migration to a different css.
As net_cls is always disabled but still mounted on cgroup v2, whenever
a process is migrated on the cgroup v2 hierarchy, net_cls sees
identity migration from root to root and cgroup core used to call
->css_attach callback for those. The net_cls ->css_attach ends up
calling update_classid() on the root net_cls css to which all
processes on the system belong to as the controller isn't used. This
makes any cgroup v2 migration O(total_number_of_fds_on_the_system)
which is horrible and easily leads to noticeable stalls triggering RCU
stall warnings and so on.
The worst symptom is already fixed in upstream by bfc2cf6f61fc
("cgroup: call subsys->*attach() only for subsystems which are
actually affected by migration"); however, backporting that commit is
too invasive and we want to avoid other cases too.
This patch updates net_cls's cgrp_attach() to iterate fds of only the
processes which are actually getting migrated. This removes the
surprising migration cost which is dependent on the total number of
fds in the target cgroup. As this leaves write_classid() the only
user of update_classid(), open-code the helper into write_classid().
Reported-by: David Goode <dgoode@fb.com> Fixes: 3b13758f51de ("cgroups: Allow dynamically changing net_classid") Cc: stable@vger.kernel.org # v4.4+ Cc: Nina Schiff <ninasc@fb.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Lindgren [Sun, 19 Mar 2017 16:19:57 +0000 (09:19 -0700)]
net: qmi_wwan: Add USB IDs for MDM6600 modem on Motorola Droid 4
This gets qmicli working with the MDM6600 modem.
Cc: Bjørn Mork <bjorn@mork.no> Reviewed-by: Sebastian Reichel <sre@kernel.org> Tested-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
Zi Shen Lim [Mon, 20 Mar 2017 06:03:14 +0000 (23:03 -0700)]
selftests/bpf: fix broken build, take 2
Merge of 'linux-kselftest-4.11-rc1':
1. Partially removed use of 'test_objs' target, breaking force rebuild of
BPFOBJ, introduced in commit d498f8719a09 ("bpf: Rebuild bpf.o for any
dependency update").
Update target so dependency on BPFOBJ is restored.
2. Introduced commit 2047f1d8ba28 ("selftests: Fix the .c linking rule")
which fixes order of LDLIBS.
Commit d02d8986a768 ("bpf: Always test unprivileged programs") added
libcap dependency into CFLAGS. Use LDLIBS instead to fix linking of
test_verifier.
3. Introduced commit d83c3ba0b926 ("selftests: Fix selftests build to
just build, not run tests").
Reordering the Makefile allows us to remove the 'all' target.
Tested both:
selftests/bpf$ make
and
selftests$ make TARGETS=bpf
on Ubuntu 16.04.2.
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Tested-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Tested-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Shuah Khan <shuahkh@osg.samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
SOF_TIMESTAMPING_OPT_STATS can be enabled and disabled
while packets are collected on the error queue.
So, checking SOF_TIMESTAMPING_OPT_STATS in sk->sk_tsflags
is not enough to safely assume that the skb contains
OPT_STATS data.
Add a bit in sock_exterr_skb to indicate whether the
skb contains opt_stats data.
Fixes: 1c885808e456 ("tcp: SOF_TIMESTAMPING_OPT_STATS option for SO_TIMESTAMPING") Reported-by: JongHwan Kim <zzoru007@gmail.com> Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tcp: fix SCM_TIMESTAMPING_OPT_STATS for normal skbs
__sock_recv_timestamp can be called for both normal skbs (for
receive timestamps) and for skbs on the error queue (for transmit
timestamps).
Commit 1c885808e456
(tcp: SOF_TIMESTAMPING_OPT_STATS option for SO_TIMESTAMPING)
assumes any skb passed to __sock_recv_timestamp are from
the error queue, containing OPT_STATS in the content of the skb.
This results in accessing invalid memory or generating junk
data.
To fix this, set skb->pkt_type to PACKET_OUTGOING for packets
on the error queue. This is safe because on the receive path
on local sockets skb->pkt_type is never set to PACKET_OUTGOING.
With that, copy OPT_STATS from a packet, only if its pkt_type
is PACKET_OUTGOING.
Fixes: 1c885808e456 ("tcp: SOF_TIMESTAMPING_OPT_STATS option for SO_TIMESTAMPING") Reported-by: JongHwan Kim <zzoru007@gmail.com> Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sat, 18 Mar 2017 11:12:22 +0000 (19:12 +0800)]
sctp: remove temporary variable confirm from sctp_packet_transmit
Commit c86a773c7802 ("sctp: add dst_pending_confirm flag") introduced
a temporary variable "confirm" in sctp_packet_transmit.
But it broke the rule that longer lines should be above shorter ones.
Besides, this variable is not necessary, so this patch is to just
remove it and use tp->dst_pending_confirm directly.
Fixes: c86a773c7802 ("sctp: add dst_pending_confirm flag") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Fri, 17 Mar 2017 23:07:11 +0000 (16:07 -0700)]
net: vrf: Reset rt6i_idev in local dst after put
The VRF driver takes a reference to the inet6_dev on the VRF device for
its rt6_local dst when handling local traffic through the VRF device as
a loopback. When the device is deleted the driver does a put on the idev
but does not reset rt6i_idev in the rt6_info struct. When the dst is
destroyed, dst_destroy calls ip6_dst_destroy which does a second put for
what is essentially the same reference causing it to be prematurely freed.
Reset rt6i_idev after the put in the vrf driver.
Fixes: b4869aa2f881e ("net: vrf: ipv6 support for local traffic to
local addresses") Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Fri, 17 Mar 2017 20:52:35 +0000 (23:52 +0300)]
bna: integer overflow bug in debugfs
We could allocate less memory than intended because we do:
bnad->regdata = kzalloc(len << 2, GFP_KERNEL);
The shift can overflow leading to a crash. This is debugfs code so the
impact is very small.
Fixes: 7afc5dbde091 ("bna: Add debugfs interface.") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Rasesh Mody <rasesh.mody@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 17 Mar 2017 15:05:28 +0000 (08:05 -0700)]
sch_dsmark: fix invalid skb_cow() usage
skb_cow(skb, sizeof(ip header)) is not very helpful in this context.
First we need to use pskb_may_pull() to make sure the ip header
is in skb linear part, then use skb_try_make_writable() to
address clones issues.
Fixes: 4c30719f4f55 ("[PKT_SCHED] dsmark: handle cloned and non-linear skb's") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey Ulanov [Wed, 15 Mar 2017 03:16:42 +0000 (20:16 -0700)]
net: unix: properly re-increment inflight counter of GC discarded candidates
Dmitry has reported that a BUG_ON() condition in unix_notinflight()
may be triggered by a simple code that forwards unix socket in an
SCM_RIGHTS message.
That is caused by incorrect unix socket GC implementation in unix_gc().
The GC first collects list of candidates, then (a) decrements their
"children's" inflight counter, (b) checks which inflight counters are
now 0, and then (c) increments all inflight counters back.
(a) and (c) are done by calling scan_children() with inc_inflight or
dec_inflight as the second argument.
Commit 6209344f5a37 ("net: unix: fix inflight counting bug in garbage
collector") changed scan_children() such that it no longer considers
sockets that do not have UNIX_GC_CANDIDATE flag. It also added a block
of code that that unsets this flag _before_ invoking
scan_children(, dec_iflight, ). This may lead to incorrect inflight
counters for some sockets.
This change fixes this bug by changing order of operations:
UNIX_GC_CANDIDATE is now unset only after all inflight counters are
restored to the original state.
David S. Miller [Tue, 21 Mar 2017 21:41:47 +0000 (14:41 -0700)]
Merge branch 'vsock-pkt-cancel'
Peng Tao says:
====================
vsock: cancel connect packets when failing to connect
Currently, if a connect call fails on a signal or timeout (e.g., guest is still
in the process of starting up), we'll just return to caller and leave the connect
packet queued and they are sent even though the connection is considered a failure,
which can confuse applications with unwanted false connect attempt.
The patchset enables vsock (both host and guest) to cancel queued packets when
a connect attempt is considered to fail.
v5 changelog:
- change virtio_vsock_pkt->cancel_token back to virtio_vsock_pkt->vsk
v4 changelog:
- drop two unnecessary void * cast
- update new callback comment
v3 changelog:
- define cancel_pkt callback in struct vsock_transport rather than struct virtio_transport
- rename virtio_vsock_pkt->vsk to virtio_vsock_pkt->cancel_token
v2 changelog:
- fix queued_replies counting and resume tx/rx when necessary
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Tao [Wed, 15 Mar 2017 01:32:17 +0000 (09:32 +0800)]
vsock: cancel packets when failing to connect
Otherwise we'll leave the packets queued until releasing vsock device.
E.g., if guest is slow to start up, resulting ETIMEDOUT on connect, guest
will get the connect requests from failed host sockets.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Reviewed-by: Jorgen Hansen <jhansen@vmware.com> Signed-off-by: Peng Tao <bergwolf@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Tao [Wed, 15 Mar 2017 01:32:15 +0000 (09:32 +0800)]
vhost-vsock: add pkt cancel capability
To allow canceling all packets of a connection.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Reviewed-by: Jorgen Hansen <jhansen@vmware.com> Signed-off-by: Peng Tao <bergwolf@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 14 Mar 2017 10:25:57 +0000 (18:25 +0800)]
crypto: deadlock between crypto_alg_sem/rtnl_mutex/genl_mutex
On Tue, Mar 14, 2017 at 10:44:10AM +0100, Dmitry Vyukov wrote:
>
> Yes, please.
> Disregarding some reports is not a good way long term.
Please try this patch.
---8<---
Subject: netlink: Annotate nlk cb_mutex by protocol
Currently all occurences of nlk->cb_mutex are annotated by lockdep
as a single class. This causes a false lcokdep cycle involving
genl and crypto_user.
This patch fixes it by dividing cb_mutex into individual classes
based on the netlink protocol. As genl and crypto_user do not
use the same netlink protocol this breaks the false dependency
loop.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
hayeswang [Tue, 14 Mar 2017 06:15:20 +0000 (14:15 +0800)]
r8152: fix the list rx_done may be used without initialization
The list rx_done would be initialized when the linking on occurs.
Therefore, if a napi is scheduled without any linking on before,
the following kernel panic would happen.
BUG: unable to handle kernel NULL pointer dereference at 000000000000008
IP: [<ffffffffc085efde>] r8152_poll+0xe1e/0x1210 [r8152]
PGD 0
Oops: 0002 [#1] SMP
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huang Ying [Mon, 20 Mar 2017 06:26:42 +0000 (14:26 +0800)]
mm, swap: Remove WARN_ON_ONCE() in free_swap_slot()
Before commit 452b94b8c8c7 ("mm/swap: don't BUG_ON() due to
uninitialized swap slot cache"), the following bug is reported,
------------[ cut here ]------------
kernel BUG at mm/swap_slots.c:270!
invalid opcode: 0000 [#1] SMP
CPU: 5 PID: 1745 Comm: (sd-pam) Not tainted 4.11.0-rc1-00243-g24c534bb161b #1
Hardware name: System manufacturer System Product Name/Z170-K, BIOS 1803 05/06/2016
RIP: 0010:free_swap_slot+0xba/0xd0
Call Trace:
swap_free+0x36/0x40
do_swap_page+0x360/0x6d0
__handle_mm_fault+0x880/0x1080
handle_mm_fault+0xd0/0x240
__do_page_fault+0x232/0x4d0
do_page_fault+0x20/0x70
page_fault+0x22/0x30
---[ end trace aefc9ede53e0ab21 ]---
This is raised by the BUG_ON(!swap_slot_cache_initialized) in
free_swap_slot(). This is incorrect, because even if the swap slots
cache fails to be initialized, the swap should operate properly without
the swap slots cache. And the use_swap_slot_cache check later in the
function will protect the uninitialized swap slots cache case.
In commit 452b94b8c8c7, the BUG_ON() is replaced by WARN_ON_ONCE(). In
the patch, the WARN_ON_ONCE() is removed too.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: Tim Chen <tim.c.chen@linux.intel.com> Cc: Michal Hocko <mhocko@suse.com> Signed-off-by: "Huang, Ying" <ying.huang@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 21 Mar 2017 20:10:17 +0000 (13:10 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Nine small fixes: the biggest is probably finally sorting out Kconfig
issues with lpfc nvme. There are some performance fixes for megaraid
and hpsa and a static checker fix"
[ Johannes Thumshirn points out that there still seems to be more lpfc
vs nvme config issues. Oh well. - Linus ]
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: Finalize Kconfig options for nvme
scsi: ufs: don't check unsigned type for a negative value
scsi: hpsa: do not timeout reset operations
scsi: hpsa: limit outstanding rescans
scsi: hpsa: update check for logical volume status
scsi: megaraid_sas: Driver version upgrade
scsi: megaraid_sas: raid6 also require cpuSel check same as raid5
scsi: megaraid_sas: add correct return type check for ldio hint logic for raid1
scsi: megaraid_sas: enable intx only if msix request fails
Linus Torvalds [Tue, 21 Mar 2017 20:07:18 +0000 (13:07 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- regression fixes for Wacom devices, from Aaron Armstrong Skomra and
Ping Cheng
- memory leak in hid-sony driver from Roderick Colenbrander
- new device IDs support from Oscar Campos and Daniel Drake
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wacom: generic: Wacom mouse is only provided for opaque tablets
HID: corsair: Add driver Scimitar Pro RGB gaming mouse 1b1c:1b3e support to hid-corsair
HID: corsair: support for K65-K70 Rapidfire and Scimitar Pro RGB
HID: wacom: don't manually release resources for the EKR
HID: wacom: Correct Intuos Pro 2 resolution
HID: sony: Fix input device leak when connecting a DS4 twice using USB/BT
HID: chicony: Add support for another ASUS Zen AiO keyboard
Linus Torvalds [Tue, 21 Mar 2017 20:01:53 +0000 (13:01 -0700)]
Merge tag 'gpio-v4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Here is the first set of GPIO fixes for 4.11. It was delayed a bit
beacuse I was chicken when linux-next was not rotating last week.
This hits the ST serial driver in drivers/tty/serial and that has an
ACK from Greg, he suggested to keep the old GPIO fwnode API around to
smoothen things in the merge Windod and those have now served their
purpose so we take them out and convert the last driver to the new
API.
Apart from that it's fixes as usual.
Summary:
- set the parent on the Altera A10SR driver, also fix high level
IRQs.
- fix error path on the mockup driver.
- compilation noise about unused functions fixed.
- fix missed interrupts on the MCP23S08 expander, this is also tagged
for stable.
- retire the interrim helpers devm_get_gpiod_from_child() used to
smoothen merging in the merge window"
* tag 'gpio-v4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio:mcp23s08 Fixed missing interrupts
serial: st-asc: Use new GPIOD API to obtain RTS pin
gpio: altera: Use handle_level_irq when configured as a level_high
gpio: xgene: mark PM functions as __maybe_unused
gpio: mockup: return -EFAULT if copy_from_user() fails
gpio: altera-a10sr: Set gpio_chip parent property
Linus Torvalds [Tue, 21 Mar 2017 19:27:06 +0000 (12:27 -0700)]
Merge tag 'for-f2fs-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs fixes from Jaegeuk Kim:
- fix performance regression reported by lkp-rebot
- fix potential data lost after power-cut due to SSR reallocation
* tag 'for-f2fs-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs:
f2fs: combine nat_bits and free_nid_bitmap cache
f2fs: skip scanning free nid bitmap of full NAT blocks
f2fs: use __set{__clear}_bit_le
f2fs: declare static functions
f2fs: don't overwrite node block by SSR
Ping Cheng [Wed, 15 Mar 2017 00:08:16 +0000 (17:08 -0700)]
HID: wacom: generic: Wacom mouse is only provided for opaque tablets
Commit f85c9dc ("Support tool ID and additional tool types") introduced mouse
and lens cursor tools to generic codepath, which covers both display (direct)
and opaque tablets (indirect devices). However, mouse and lens cursor tools are
only provided for opaque tablets. This patch ignores mouse and lens cursor tools
if the device is a display tablet.
Oscar Campos [Mon, 6 Mar 2017 21:02:39 +0000 (21:02 +0000)]
HID: corsair: Add driver Scimitar Pro RGB gaming mouse 1b1c:1b3e support to hid-corsair
This mouse sold by Corsair as Scimitar PRO RGB defines two consecutive
Logical Minimum items in its Application (Consumer.0001) report making
it non parseable. This patch fixes the report descriptor overriding
byte 77 in rdesc from 0x16 (Logical Minimum with 16 bits value) to 0x26
(Logical Maximum with 16 bits value).
Signed-off-by: Oscar Campos <oscar.campos@member.fsf.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
HID: wacom: don't manually release resources for the EKR
Commit 5b779fc introduces the manual release of resources in wacom_remove() as
an addition to the driver's use of devm. The EKR resources can only be
released through wacom_remote_destroy_one() so we skip the manual release for
it.
Fixes: 5b779fc ("HID: wacom: release the resources before leaving despite devm") Signed-off-by: Aaron Armstrong Skomra <skomra@gmail.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Takashi Iwai [Tue, 21 Mar 2017 12:56:04 +0000 (13:56 +0100)]
ALSA: seq: Fix racy cell insertions during snd_seq_pool_done()
When snd_seq_pool_done() is called, it marks the closing flag to
refuse the further cell insertions. But snd_seq_pool_done() itself
doesn't clear the cells but just waits until all cells are cleared by
the caller side. That is, it's racy, and this leads to the endless
stall as syzkaller spotted.
This patch addresses the racy by splitting the setup of pool->closing
flag out of snd_seq_pool_done(), and calling it properly before
snd_seq_pool_done().
Takashi Iwai [Tue, 21 Mar 2017 12:26:02 +0000 (13:26 +0100)]
ALSA: x86: Make CONFIG_SND_X86 bool
CONFIG_SND_X86 is a menu config to filter only for x86-specific
drivers in its sub-menu, and this doesn't have to be tristate but
rather it should be a bool. Also, like other sub-menu configs, it's
more user-friendly to be default=y; it's merely a menu config and the
actual drivers are configured in the sub-menu, after all.
projects / mirror_ubuntu-artful-kernel.git / log