The SR-IOV spec requires that VFs must report zero for the INTx pin
register as VFs are precluded from INTx support. It's much easier for
the host kernel to understand whether a device is a VF and therefore
whether a non-zero pin register value is bogus than it is to do the
same in userspace. Override the INTx count for such devices and
virtualize the pin register to provide a consistent view of the device
to the user.
As this is clearly a spec violation, warn about it to support hardware
validation, but also provide a known whitelist as it doesn't do much
good to continue complaining if the hardware vendor doesn't plan to
fix it.
The function should return -EFAULT when copy_from_user fails. Even
though the caller does not distinguish them. but we should keep backward
compatibility.
drivers/misc/kgdbts.c: In function ‘configure_kgdbts’:
drivers/misc/kgdbts.c:1070:2: error: ‘strcpy’ source argument is the same as destination [-Werror=restrict]
strcpy(config, opt);
^~~~~~~~~~~~~~~~~~~
As the error says, config is being used in both the source and destination.
Refactor the code to avoid the extra copy and put the parsing closer to
the actual location.
Signed-off-by: Laura Abbott <labbott@redhat.com> Acked-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
>From the comment in the code, it claims the requirement for byte-address
alignment for RRP register: 'for 32-bit, 64-bit and 128-bit wide trace
memory, the four LSBs must be 0s. For 256-bit wide trace memory, the
five LSBs must be 0s'. This isn't consistent with the program, the
program sets five LSBs as zeros for 32/64/128-bit wide trace memory and
set six LSBs zeros for 256-bit wide trace memory.
After checking with the CoreSight Trace Memory Controller technical
reference manual (ARM DDI 0461B, section 3.3.4 RAM Read Pointer
Register), it proves the comment is right and the program does wrong
setting.
This patch fixes byte-address alignment for RRP by following correct
definition in the technical reference manual.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Mike Leach <mike.leach@linaro.org> Signed-off-by: Leo Yan <leo.yan@linaro.org> Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For non-VHE systems host kernel runs at EL1 and jumps to EL2 whenever
hypervisor code should be executed. In this case ETM4x driver must
restrict configuration to EL1 when it setups kernel tracing.
However, there is no separate hypervisor privilege level when VHE
is enabled, the host kernel runs at EL2.
This patch fixes configuration of TRCACATRn register for VHE systems
so that ETM_EXLEVEL_NS_HYP bit is used instead of ETM_EXLEVEL_NS_OS
to on/off kernel tracing. At the same time, it moves common code
to new helper.
We enable the trace path, before activating the source.
If we fail to enable the source, we must disable the path
to make sure it is available for another session.
We create a coresight trace path for each online CPU when
we start the event. We rely on the number of online CPUs
and then go on to allocate an array matching the "number of
online CPUs" for holding the path and then uses normal
CPU id as the index to the array. This is problematic as
we could have some offline CPUs causing us to access beyond
the actual array size (e.g, on a dual SMP system, if CPU0 is
offline, CPU1 could be really accessing beyond the array).
The solution is to switch to per-cpu array for holding the path.
The coresight components could be operated either in sysfs mode or in perf
mode. For some of the components, the mode of operation doesn't matter as
they simply relay the data to the next component in the trace path. But for
sinks, they need to be able to provide the trace data back to the user.
Thus we need to make sure that "mode" is handled appropriately. e.g,
the sysfs mode could have multiple sources driving the trace data, while
perf mode doesn't allow sharing the sink.
The coresight_enable_sink() however doesn't really allow this check to
trigger as it skips the "enable_sink" callback if the component is
already enabled, irrespective of the mode. This could cause mixing
of data from different modes or even same mode (in perf), if the
sources are different. Also, if we fail to enable the sink while
enabling a path (where sink is the first component enabled),
we could end up in disabling the components in the "entire"
path which were not enabled in this trial, causing disruptions
in the existing trace paths.
When USB requests for video data fail to be submitted, the driver
signals a problem to the host by halting the video streaming endpoint.
This is only valid in bulk mode, as isochronous transfers have no
handshake phase and can't thus report a stall. The usb_ep_set_halt()
call returns an error when using isochronous endpoints, which we happily
ignore, but some UDCs complain in the kernel log. Fix this by only
trying to halt the endpoint in bulk mode.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Paul Elder <paul.elder@ideasonboard.com> Tested-by: Paul Elder <paul.elder@ideasonboard.com> Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
USB requests for video data are queued from two different locations in
the driver, with the same code block occurring twice. Factor it out to a
function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Paul Elder <paul.elder@ideasonboard.com> Tested-by: Paul Elder <paul.elder@ideasonboard.com> Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When runtime is not enabled, pm_runtime_get_sync() returns -EACCESS,
the counter will be incremented but the resume callback not called,
so enumeration and charging will not start properly.
To avoid that happen, disable irq on suspend and recheck on resume.
Practically this happens when the device is woken up from suspend by
plugging in usb.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Broadcom ARM-based DSL SoCs (BCM63xx product line) have the same
Broadcom SATA PHY that other SoCs are using, make it possible to select
that driver on these platforms.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The function that computes clock parameters from divisors did not
respect the maximum size of the bitfields that the parameters were
written to. This fixes the bug.
This bug can be reproduced with (and this fix verified with) the test
at: https://kunit-review.googlesource.com/c/linux/+/1035/
While checks are in place to avoid attributes and children of a format
being manipulated after the format is linked into the streaming header,
the linked flag was never actually set, invalidating the protections.
Update the flag as appropriate in the header link calls.
Some of the .allow_link() and .drop_link() operations implementations
call config_group_find_item() and then leak the reference to the
returned item. Fix this by dropping those references where needed.
It is good practice to make the setting of gpio-pinctrls explicitly in the
devicetree, and in this case even necessary.
Rockchip boards start with iomux settings set to gpio for most pins and
while the linux pinctrl driver also implicitly sets the gpio function if
a pin is requested as gpio that is not necessarily true for other drivers.
The issue in question stems from uboot, where the sdmmc_pwr pin is set
to function 1 (sdmmc-power) by the bootrom when reading the 1st-stage
loader. The regulator controlled by the pin is active-low though, so
when the dwmmc hw-block sets its enabled bit, it actually disables the
regulator. By changing the pin back to gpio we fix that behaviour.
Clang warns when one enumerated type is implicitly converted to another.
drivers/media/platform/davinci/vpbe_display.c:524:24: warning: implicit
conversion from enumeration type 'enum osd_v_exp_ratio' to different
enumeration type 'enum osd_h_exp_ratio' [-Wenum-conversion]
layer_info->h_exp = V_EXP_6_OVER_5;
~ ^~~~~~~~~~~~~~
1 warning generated.
This appears to be a copy and paste error judging from the couple of
lines directly above this statement and the way that height is handled
in the if block above this one.
Reported-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The microSD card slot in the Sapphire board is not working because of
several issues:
1.- The vmmc power supply is missing in the DTS. It is capable of 3.0V
and has a GPIO-based enable control.
2.- The vqmmc power supply can provide up to 3.3V, but it is capped in
the DTS to just 3.0V because of the vmmc capability. This results in a
conflict from the mmc driver requesting an unsupportable voltage range
from 3.3V to 3.0V (min > max) as reported in dmesg. So, extend the
range up to 3.3V. The hw should be able to stand this 0.3V tolerance.
See mmc_regulator_set_vqmmc in drivers/mmc/core/core.c.
3.- The card detect signal is non-working. There is a known conflict
with jtag, but the workaround in drivers/soc/rockchip/grf.c does not
work. Adding the broken-cd attribute to the DTS fixes the issue.
Presently we check first if CPUID is enabled. If it is not already
enabled, then we next call identify_cpu_without_cpuid() and clear
X86_FEATURE_CPUID.
Unfortunately, identify_cpu_without_cpuid() is the function where CPUID
becomes _enabled_ on Cyrix 6x86/6x86L CPUs.
Reverse the calling sequence so that CPUID is first enabled, and then
check a second time to see if the feature has now been activated.
[ bp: Massage commit message and remove trailing whitespace. ]
Suggested-by: Andy Lutomirski <luto@amacapital.net> Signed-off-by: Matthew Whitehead <tedheadster@gmail.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Andy Lutomirski <luto@amacapital.net> Cc: David Woodhouse <dwmw@amazon.co.uk> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20180921212041.13096-3-tedheadster@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This is because it expands the macro into a non-functioning calling
sequence. The calling order must be:
outb(CX86_CCR2, 0x22);
inb(0x23);
From the comments:
* When using the old macros a line like
* setCx86(CX86_CCR2, getCx86(CX86_CCR2) | 0x88);
* gets expanded to:
* do {
* outb((CX86_CCR2), 0x22);
* outb((({
* outb((CX86_CCR2), 0x22);
* inb(0x23);
* }) | 0x88), 0x23);
* } while (0);
The new macros fix this problem, so use them instead.
Signed-off-by: Matthew Whitehead <tedheadster@gmail.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Andy Lutomirski <luto@amacapital.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Jia Zhang <qianyue.zj@alibaba-inc.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Philippe Ombredanne <pombredanne@nexb.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20180921212041.13096-2-tedheadster@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Allow the configuration of the MDIO clock divider when the Device Tree
contains 'clock-frequency' property (similar to I2C and SPI buses).
Because the hardware may have lost its state during suspend/resume,
re-apply the MDIO clock divider upon resumption.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
following commit:
commit d58e468b1112 ("flow_dissector: implements flow dissector BPF hook")
added struct bpf_flow_keys which conflicts with the struct with
same name in sockex2_kern.c and sockex3_kern.c
similar to commit:
commit 534e0e52bc23 ("samples/bpf: fix a compilation failure")
we tried the rename it "flow_keys" but it also conflicted with struct
having same name in include/net/flow_dissector.h. Hence renaming the
struct to "flow_key_record". Also, this commit doesn't fix the
compilation error completely because the similar struct is present in
sockex3_kern.c. Hence renaming it in both files sockex3_user.c and
sockex3_kern.c
Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp> Acked-by: Song Liu <songliubraving@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This is a workaround for FW bug -
MFW generates bandwidth attention in single function mode, which
is only expected to be generated in multi function mode.
This undesired attention in SF mode results in incorrect HW
configuration and resulting into Tx timeout.
Signed-off-by: Shahed Shaikh <Shahed.Shaikh@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
dtc has new checks for I2C and SPI buses. Fix the warnings in node names
and unit-addresses.
arch/arm/boot/dts/dove-cubox.dtb: Warning (i2c_bus_reg): /i2c-mux/i2c@0/clock-generator: I2C bus unit address format error, expected "60"
arch/arm/boot/dts/dove-cubox-es.dtb: Warning (i2c_bus_reg): /i2c-mux/i2c@0/clock-generator: I2C bus unit address format error, expected "60"
arch/arm/boot/dts/dove-cubox.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@10600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dove-cubox-es.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@10600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dove-dove-db.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@10600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dove-sbc-a510.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@10600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dove-sbc-a510.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@14600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/orion5x-kuroboxpro.dtb: Warning (i2c_bus_reg): /soc/internal-regs/i2c@11000/rtc: I2C bus unit address format error, expected "32"
arch/arm/boot/dts/orion5x-linkstation-lschl.dtb: Warning (i2c_bus_reg): /soc/internal-regs/i2c@11000/rtc: I2C bus unit address format error, expected "32"
arch/arm/boot/dts/orion5x-linkstation-lsgl.dtb: Warning (i2c_bus_reg): /soc/internal-regs/i2c@11000/rtc: I2C bus unit address format error, expected "32"
arch/arm/boot/dts/orion5x-linkstation-lswtgl.dtb: Warning (i2c_bus_reg): /soc/internal-regs/i2c@11000/rtc: I2C bus unit address format error, expected "32"
Cc: Jason Cooper <jason@lakedaemon.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Cc: Gregory Clement <gregory.clement@bootlin.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The table id (second) argument to MODULE_DEVICE_TABLE is often
referenced otherwise. This is not the case for CPU features. This
leads to a warning when building the kernel with Clang:
arch/arm/crypto/crc32-ce-glue.c:239:33: warning: variable
'crc32_cpu_feature' is not needed and will not be emitted
[-Wunneeded-internal-declaration]
static const struct cpu_feature crc32_cpu_feature[] = {
^
Avoid warnings by using __maybe_unused, similar to commit 1f318a8bafcf
("modules: mark __inittest/__exittest as __maybe_unused").
Fixes: 2a9faf8b7e43 ("crypto: arm/crc32 - enable module autoloading based on CPU feature bits") Signed-off-by: Stefan Agner <stefan@agner.ch> Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The table id (second) argument to MODULE_DEVICE_TABLE is often
referenced otherwise. This is not the case for CPU features. This
leads to warnings when building the kernel with Clang:
arch/arm/crypto/aes-ce-glue.c:450:1: warning: variable
'cpu_feature_match_AES' is not needed and will not be emitted
[-Wunneeded-internal-declaration]
module_cpu_feature_match(AES, aes_init);
^
Avoid warnings by using __maybe_unused, similar to commit 1f318a8bafcf
("modules: mark __inittest/__exittest as __maybe_unused").
Fixes: 67bad2fdb754 ("cpu: add generic support for CPU feature based module autoloading") Signed-off-by: Stefan Agner <stefan@agner.ch> Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Clang warns when one enumerated type is converted implicitly to another:
drivers/spi/spi-pic32.c:323:8: warning: implicit conversion from
enumeration type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
DMA_FROM_DEVICE,
^~~~~~~~~~~~~~~
drivers/spi/spi-pic32.c:333:8: warning: implicit conversion from
enumeration type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
DMA_TO_DEVICE,
^~~~~~~~~~~~~
2 warnings generated.
Use the proper enums from dma_transfer_direction (DMA_FROM_DEVICE =
DMA_DEV_TO_MEM = 2, DMA_TO_DEVICE = DMA_MEM_TO_DEV = 1) to satify Clang.
Link: https://github.com/ClangBuiltLinux/linux/issues/159 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
am335x-evm has only one CPSW external port physically wired, but DT defines
2 ext. ports. As result, PHY connection failure reported for the second
ext. port.
Update DT to reflect am335x-evm board HW configuration, and, while here,
switch to use phy-handle instead of phy_id.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
With introduction of MC-aware mode to mlxsw, it became necessary to
configure TCs above 7 as well. There is now code in mlxsw to disable ETS
for these higher classes, but disablement of max shaper was neglected.
By default, max shaper is currently disabled to begin with, so the
problem is just cosmetic. However, for symmetry, do like we do for ETS
configuration, and call mlxsw_sp_port_ets_maxrate_set() for both TC i
and i + 8.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
At OTG work running time, it's possible that several events need to be
addressed (e.g. ID and VBUS events). The current implementation handles
only one event at a time which leads to ignoring the other one. Fix it.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When initializing the USB subsystem before starting the kernel,
OTG overcurrent detection is disabled. In case the OTG polarity of
overcurrent is low active, the overcurrent detection is never enabled
again and events cannot be reported as expected. Because imx usb
overcurrent polarity is low active by default, only detection needs
to be enable in usbmisc init function.
Signed-off-by: Nicolas Adell <nicolas.adell@actia.fr> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
NFP supports fairly enormous ring sizes (up to 256k descriptors).
In commit 466271703867 ("nfp: use kvcalloc() to allocate SW buffer
descriptor arrays") we have started using kvcalloc() functions to
make sure the allocation of software state arrays doesn't hit
the MAX_ORDER limit. Unfortunately, we can't use virtual mappings
for the DMA region holding HW descriptors. In case this allocation
fails instead of the generic (and fairly scary) warning/splat in
the logs print a helpful message explaining what happened and
suggesting how to fix it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Shannon Nelson <shannon.nelson@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This avoids getting woken up from suspend after power interruptions
when the bci wrongly thinks the battery is full just because
of input current going low because of low input power
Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
the charging current uses unsigned int variables, if we step back
if the current is still low, we would run into negative which
means setting the target to a huge value.
Better add checks here.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The next update of libfdt has a new dependency on INT_MAX. Update the
instances of libfdt_env.h in the kernel to either include the necessary
header with the definition or define it locally.
Cc: Russell King <linux@armlinux.org.uk> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: linux-arm-kernel@lists.infradead.org Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit f27b4746f378 ("i40iw: add connection management code") uses an
incorrect rcu iterator, whilst holding the rtnl_lock. Since the
critical region invokes i40iw_manage_qhash(), which is a sleeping
function, the rcu locking and traversal cannot be used.
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This re-applies commit b91c1e3e7a6f ("powerpc: Fix duplicate const
clang warning in user access code") (Jun 2015) which was undone in
commits: f2ca80905929 ("powerpc/sparse: Constify the address pointer in __get_user_nosleep()") (Feb 2017) d466f6c5cac1 ("powerpc/sparse: Constify the address pointer in __get_user_nocheck()") (Feb 2017) f84ed59a612d ("powerpc/sparse: Constify the address pointer in __get_user_check()") (Feb 2017)
We see a large number of duplicate const errors in the user access
code when building with llvm/clang:
The problem is we are doing const __typeof__(*(ptr)), which will hit
the warning if ptr is marked const.
Removing const does not seem to have any effect on GCC code
generation.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When performing partition migrations all present CPUs must be online
as all present CPUs must make the H_JOIN call as part of the migration
process. Once all present CPUs make the H_JOIN call, one CPU is returned
to make the rtas call to perform the migration to the destination system.
During testing of migration and changing the SMT state we have found
instances where CPUs are offlined, as part of the SMT state change,
before they make the H_JOIN call. This results in a hung system where
every CPU is either in H_JOIN or offline.
To prevent this this patch disables CPU hotplug during the migration
process.
This causes SLB alloation to start 1 beyond the start of the SLB.
There is no real problem because after it wraps it stats behaving
properly, it's just surprisig to see when looking at SLB traces.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, also the implementation in this
driver has returns 'netdev_tx_t' value, so just change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Looking at logs from systems all over the place, it looks like tons
of broken systems exist that set the base address to zero. I can
only guess that is some sort of non-standard idea to mark the
interface as not being present. It can't be zero, anyway, so just
complain and ignore it.
Mediatek SPI driver modifies some fields (tx_buf, rx_buf, len, tx_dma,
rx_dma) of the spi_transfer* passed in when doing transfer_one and in
interrupt handler. This is somewhat unexpected, and there are some
caller (e.g. Cr50 spi driver) that reuse the spi_transfer for multiple
messages. Add a field to record how many bytes have been transferred,
and calculate the right len / buffer based on it instead.
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Change-Id: I23e218cd964f16c0b2b26127d4a5ca6529867673 Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
samples/bpf build failed with the following errors:
$ make samples/bpf/
...
HOSTCC samples/bpf/sockex3_user.o
/data/users/yhs/work/net-next/samples/bpf/sockex3_user.c:16:8: error: redefinition of ‘struct bpf_flow_keys’
struct bpf_flow_keys {
^
In file included from /data/users/yhs/work/net-next/samples/bpf/sockex3_user.c:4:0:
./usr/include/linux/bpf.h:2338:9: note: originally defined here
struct bpf_flow_keys *flow_keys;
^
make[3]: *** [samples/bpf/sockex3_user.o] Error 1
Commit d58e468b1112d ("flow_dissector: implements flow dissector BPF hook")
introduced struct bpf_flow_keys in include/uapi/linux/bpf.h and hence
caused the naming conflict with samples/bpf/sockex3_user.c.
The fix is to rename struct bpf_flow_keys in samples/bpf/sockex3_user.c
to flow_keys to avoid the conflict.
Signed-off-by: Yonghong Song <yhs@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On the error path of mxs_auart_request_gpio_irq() is performed
backward iterating with index i of enum type. Underline enum type
may be unsigned char. In this case check (--i >= 0) will be always
true and error handling goes into infinite loop.
The patch changes the check so that it is valid for signed and unsigned
types.
Found by Linux Driver Verification project (linuxtesting.org).
The driver's suspend/resume functions were buggy.
If UART node contains any child node in the DT and
the child is established a communication path with
the parent UART. The relevant /dev/ttyPS* node will
be not available for other operations.
If the driver is trying to do any operations like
suspend/resume without checking the tty->dev status
it leads to the kernel crash/hang.
This patch fix this issue by call the device_may_wake()
with the generic parameter of type struct device.
in the uart suspend and resume paths.
It also fixes a race condition in the uart suspend
path(i.e uart_suspend_port() should be called at the
end of cdns_uart_suspend API this path updates the same)
Signed-off-by: Nava kishore Manne <navam@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Calling napi_schedule() from process context does not ensure that the
NET_RX softirq is run in a timely fashion. So trigger it manually.
This is no big issue with current code. A call to ndo_open() is usually
followed by a ndo_set_rx_mode() call, and for qeth this contains a
spin_unlock_bh(). Except for OSN, where qeth_l2_set_rx_mode() bails out
early.
Nevertheless it's best to not depend on this behaviour, and just fix
the issue at its source like all other drivers do. For instance see
commit 83a0c6e58901 ("i40e: Invoke softirqs after napi_reschedule").
Fixes: a1c3ed4c9ca0 ("qeth: NAPI support for l2 and l3 discipline") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We tried to revert commit d9c52fd17cb4 ("ath9k: fix tx99 with monitor
mode interface") but accidentally missed part of the locking change.
The lock has to be held earlier so that we're holding it when we do
"sc->tx99_vif = vif;" and also there in the current code there is a
stray unlock before we have taken the lock.
Fixes: 6df0580be8bc ("ath9k: add back support for using active monitor interfaces for tx99") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
lpss_iosf_enter_d3_state() checks if all hw-blocks using the DMA
controllers are in d3 before powering down the DMA controllers.
But on devices, where the I2C bus connected to the PMIC is shared by
the PUNIT, the controller for that bus will never reach d3 since it has
an effectively empty _PS3 method. Instead it appears to automatically
power-down during S0i3 and we never see it as being in d3.
This causes the DMA controllers to never be powered-down on these devices,
causing them to never reach S0i3. This commit uses the ACPI _SEM method
to detect if an I2C bus is shared with the PUNIT and if it is, it removes
it from the mask of devices which lpss_iosf_enter_d3_state() checks for.
This fixes these devices never reaching any S0ix states.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
dtc has new checks for SPI buses. The rk3036 dts file has a node named
spi' which causes false positive warnings. As the node is a pinctrl child
node, change the node name to be 'spi-pins' to fix the warnings.
arch/arm/boot/dts/rk3036-evb.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #address-cells for SPI bus
arch/arm/boot/dts/rk3036-kylin.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #address-cells for SPI bus
arch/arm/boot/dts/rk3036-evb.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #size-cells for SPI bus
arch/arm/boot/dts/rk3036-kylin.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #size-cells for SPI bus
gre_parse_header stops parsing when csum_err is encountered, which means
tpi->key is undefined and ip_tunnel_lookup will return NULL improperly.
This patch introduce a NULL pointer as csum_err parameter. Even when
csum_err is encountered, it won't return error and continue parsing gre
header as expected.
Fixes: 9f57c67c379d ("gre: Remove support for sharing GRE protocol hook.") Reported-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The terminating NUL byte is only there because the buffer is
allocated with kzalloc(PAGE_SIZE, GFP_KERNEL), but since the
range-check is off-by-one, and PAGE_SIZE==PATH_MAX, the
returned string may not be zero-terminated if it is exactly
PATH_MAX characters long. Furthermore also the initial loop
may theoretically exceed PATH_MAX and cause a fault.
During component_bind_all(), if bind() fails for any
particular component associated with a master, unbind()
should be called for all previous components in that
master's match array, whose bind() might have completed
successfully. As per the current logic, if bind() fails
for the component at position 'n' in the master's match
array, it would start calling unbind() from component in
'n'th position itself and work backwards, and will always
skip calling unbind() for component in 0th position in the
master's match array.
Fix this by updating the loop condition, and the logic to
refer to the components in master's match array, so that
unbind() is called for all components starting from 'n-1'st
position in the array, until (and including) component in
0th position.
Since the max8998 MFD driver supports instantiation by DT, platform data
retrieval is handled in MFD probe and cell drivers should get use
the pdata field of max8998_dev struct to obtain them.
Fixes: ee999fb3f17f ("mfd: max8998: Add support for Device Tree") Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com> Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There should be only one instance of struct shdwc in the system. This is
referenced through at91_shdwc. Return in probe if at91_shdwc is already
allocated.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If kstrtoul() fails then we print "charge_full" when it's uninitialized.
The debug printk doesn't add anything so I deleted it and cleaned these
two functions up a bit.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
dtc has new checks for SPI buses. The meson dts files have a node named
spi' which causes false positive warnings. As the node is a pinctrl child
node, change the node name to be 'spi-pins' to fix the warnings.
arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dtb: Warning (spi_bus_bridge): /soc/periphs@c8834000/pinctrl@4b0/spi: incorrect #address-cells for SPI bus
Cc: Carlo Caione <carlo@caione.org> Cc: Kevin Hilman <khilman@baylibre.com> Cc: linux-amlogic@lists.infradead.org Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
To reduce latency for interactive and soft real-time applications, bfq
privileges the bfq_queues containing the I/O of these
applications. These privileged queues, referred-to as weight-raised
queues, get a much higher share of the device throughput
w.r.t. non-privileged queues. To preserve this higher share, the I/O
of any non-weight-raised queue must be plugged whenever a sync
weight-raised queue, while being served, remains temporarily empty. To
attain this goal, bfq simply plugs any I/O (from any queue), if a sync
weight-raised queue remains empty while in service.
Unfortunately, this plugging typically lowers throughput with random
I/O, on devices with internal queueing (because it reduces the filling
level of the internal queues of the device).
This commit addresses this issue by restricting the cases where
plugging is performed: if a sync weight-raised queue remains empty
while in service, then I/O plugging is performed only if some of the
active bfq_queues are *not* weight-raised (which is actually the only
circumstance where plugging is needed to preserve the higher share of
the throughput of weight-raised queues). This restriction proved able
to boost throughput in really many use cases needing only maximum
throughput.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Do not put host-endian 0 or 1 into big endian feild.
Reported-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Sharing the same irqchip with multiple gpiochips is not a good
practice. For instance, when installing hooks, we change the state
of the irqchip. The initial state of the irqchip for the second
gpiochip to register is then disrupted.
dtc has new checks for I2C buses. Fix the warnings in unit-addresses.
arch/arm/boot/dts/socfpga_cyclone5_de0_sockit.dtb: Warning (i2c_bus_reg): /soc/i2c@ffc04000/adxl345@0: I2C bus unit address format error, expected "53"
Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Dinh Nguyen <dinguyen@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
while compiling an ipq4019 target, dtc will complain:
regulator@b089000 unit address format error, expected "2089000"
The saw0 regulator reg value seems to be
copied and pasted from qcom-ipq8064.dtsi.
This patch fixes the reg value to match that of the
unit address which in turn silences the warning.
(There is no driver for qcom,saw2 right now.
So this went unnoticed)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: John Crispin <john@phrozen.org> Signed-off-by: Andy Gross <andy.gross@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
llc_sap_close() is called by llc_sap_put() which
could be called in BH context in llc_rcv(). We can't
block in BH.
There is no reason to block it here, kfree_rcu() should
be sufficient.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The "has_config" variable is either uninitialized or true. The
"num_pins" variable is unsigned and we verified that it is non-zero on
the lines before so we know "num_pines >= 1" is true. Really, we could
just check "num_configs" directly and remove the "has_config" variable.
The interrupt handler has to be acquired after the other resource
initialization when allocated with IRQF_SHARED. Otherwise it's
triggered before the resource gets ready, and may lead to unpleasant
behavior.
The VIDEO_GET_EVENT and VIDEO_STILLPICTURE was added back in 2005 but
it never worked because the command number is wrong.
Using the right command number means we have a better chance of them
actually doing the right thing, though clearly nobody has ever tried
it successfully.
I noticed these while auditing the remaining users of compat_time_t
for y2038 bugs. This one is fine in that regard, it just never did
anything.
Motion eye video4linux driver for Sony Vaio PictureBook desn't validate user-controlled parameter
'vma->vm_pgoff', a malicious process might access all of kernel memory from user space by trying
pass different arbitrary address.
Discussion: http://www.openwall.com/lists/oss-security/2018/07/06/1
If hv_synic_alloc() errors out, the state of the per-cpu context
for some CPUs is unknown since the zero'ing is done as each
CPU is iterated over. In such case, hv_synic_cleanup() may try to
free memory based on uninitialized values. Fix this by zero'ing
the per-cpu context for all CPUs before doing any memory
allocations that might fail.
Signed-off-by: Michael Kelley <mikelley@microsoft.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Instead of calling BUG_ON(), if we find a kprobe in use on free kprobe
list, just remove it from the list and keep it on kprobe hash list
as same as other in-use kprobes.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com> Cc: David S . Miller <davem@davemloft.net> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Naveen N . Rao <naveen.n.rao@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/153666126882.21306.10738207224288507996.stgit@devbox Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When the firmware is not responding, execution of kexec boot causes a system
hang. When firmware assertion happened, driver get notified with interrupt
vector updated in MPI configuration table. Then, the driver will read
scratchpad register and set controller_fatal_error flag to true.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com> Signed-off-by: Viswas G <Viswas.G@microchip.com> Acked-by: Jack Wang <jinpu.wang@profitbricks.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For the function dma_unmap_sg(), the <nents> parameter should be number of
elements in the scatter list prior to the mapping, not after the mapping.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com> Signed-off-by: Viswas G <Viswas.G@microchip.com> Acked-by: Jack Wang <jinpu.wang@profitbricks.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
One of the Freescale recommended sequences for power off with external
PMIC is the following:
...
3. SoC is programming PMIC for power off when standby is asserted.
4. In CCM STOP mode, Standby is asserted, PMIC gates SoC supplies.
sym_int_sir() in sym_hipd.c does not check the command pointer for NULL before
using it in debug message prints.
Suggested-by: Matthew Wilcox <matthew.wilcox@oracle.com> Signed-off-by: George Kennedy <george.kennedy@oracle.com> Reviewed-by: Mark Kanda <mark.kanda@oracle.com> Acked-by: Matthew Wilcox <matthew.wilcox@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Message 6408 is displayed for each entry in an array, but the cpu and queue
numbers were incorrect for the entry. Message 6001 includes an extraneous
character.
Resolve both issues
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When FW rejects a command due to "entry_status" error (malform IOCB), the srb
resource needs to be returned back for cleanup. The filter to catch this is
in the wrong location.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For target mode, any chip reset triggered before target mode is enabled will
be held off until user is ready to enable. This prevents the chip from
starting or running before it is intended.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>