Documentation specifies that SYSMMU should be in blocked state while
performing TLB/FLPD cache invalidation, so add needed calls to
sysmmu_block/unblock.
Fixes: 66a7ed84b345d ("iommu/exynos: Apply workaround of caching fault page table entries") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
This was broken in commit cd979883b9ed ("xen/acpi-processor:
fix enabling interrupts on syscore_resume"). do_suspend (from
xen/manage.c) and thus xen_resume_notifier never get called on
the initial-domain at resume (it is if running as guest.)
The rationale for the breaking change was that upload_pm_data()
potentially does blocking work in syscore_resume(). This patch
addresses the original issue by scheduling upload_pm_data() to
execute in workqueue context.
Cc: Stanislaw Gruszka <sgruszka@redhat.com> Based-on-patch-by: Konrad Wilk <konrad.wilk@oracle.com> Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Ankur Arora <ankur.a.arora@oracle.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The intent of the original warning is make sure that the mdev vendor
driver has removed any group notifiers at the point where the group
is closed by the user. Theoretically this would be through an
orderly shutdown where any devices are release prior to the group
release. We can't always count on an orderly shutdown, the user can
close the group before the notifier can be removed or the user task
might be killed. We'd like to add this sanity test when the group is
idle and the only references are from the devices within the group
themselves, but we don't have a good way to do that. Instead check
both when the group itself is removed and when the group is opened.
A bit later than we'd prefer, but better than the current over
aggressive approach.
Fixes: ccd46dbae77d ("vfio: support notifier chain in vfio_group") Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Cc: Jike Song <jike.song@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Filesystem encryption ostensibly supported revoking a keyring key that
had been used to "unlock" encrypted files, causing those files to become
"locked" again. This was, however, buggy for several reasons, the most
severe of which was that when key revocation happened to be detected for
an inode, its fscrypt_info was immediately freed, even while other
threads could be using it for encryption or decryption concurrently.
This could be exploited to crash the kernel or worse.
This patch fixes the use-after-free by removing the code which detects
the keyring key having been revoked, invalidated, or expired. Instead,
an encrypted inode that is "unlocked" now simply remains unlocked until
it is evicted from memory. Note that this is no worse than the case for
block device-level encryption, e.g. dm-crypt, and it still remains
possible for a privileged user to evict unused pages, inodes, and
dentries by running 'sync; echo 3 > /proc/sys/vm/drop_caches', or by
simply unmounting the filesystem. In fact, one of those actions was
already needed anyway for key revocation to work even somewhat sanely.
This change is not expected to break any applications.
In the future I'd like to implement a real API for fscrypt key
revocation that interacts sanely with ongoing filesystem operations ---
waiting for existing operations to complete and blocking new operations,
and invalidating and sanitizing key material and plaintext from the VFS
caches. But this is a hard problem, and for now this bug must be fixed.
This bug affected almost all versions of ext4, f2fs, and ubifs
encryption, and it was potentially reachable in any kernel configured
with encryption support (CONFIG_EXT4_ENCRYPTION=y,
CONFIG_EXT4_FS_ENCRYPTION=y, CONFIG_F2FS_FS_ENCRYPTION=y, or
CONFIG_UBIFS_FS_ENCRYPTION=y). Note that older kernels did not use the
shared fs/crypto/ code, but due to the potential security implications
of this bug, it may still be worthwhile to backport this fix to them.
Fixes: b7236e21d55f ("ext4 crypto: reorganize how we store keys in the inode") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Acked-by: Michael Halcrow <mhalcrow@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The CCP driver generally uses a round-robin approach when
assigning operations to available CCPs. For the DMA engine,
however, the DMA mappings of the SGs are associated with a
specific CCP. When an IOMMU is enabled, the IOMMU is
programmed based on this specific device.
If the DMA operations are not performed by that specific
CCP then addressing errors and I/O page faults will occur.
Update the CCP driver to allow a specific CCP device to be
requested for an operation and use this in the DMA engine
support.
Signed-off-by: Gary R Hook <gary.hook@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
In the 'commit ebee76f7fa46 ("ath10k: allow setting coverage class")',
it inherits the design and the address offset from ath9k, but the address
is not applicable to QCA6174, which leads to a random crash while doing the
resume() operation, since the set_coverage_class.ops will be called from
ieee80211_reconfig() when resume() (if the wow is not configured).
Fix the incorrect address offset here to avoid the random crash.
Verified on QCA6174/hw3.0 with firmware WLAN.RM.4.4-00022-QCARMSWPZ-2.
kvalo: this also seems to fix a regression with firmware restart.
Fixes: ebee76f7fa46 ("ath10k: allow setting coverage class") Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
When PCIe FLR support was added, much of the remove/release code for
PCIe was migrated to ->down_dev(), but ->down_dev() is never called for
device removal. Let's refactor the cleanup to be done in both cases.
Also, drop the comments above mwifiex_cleanup_pcie(), because they were
clearly wrong, and it's better to have clear and obvious code than to
detail the code steps in comments anyway.
Fixes: 4c5dae59d2e9 ("mwifiex: add PCIe function level reset support") Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The MP style clocks support an mux with pre-dividers. While the driver
correctly accounted for them in the .determine_rate callback, it did
not in the .recalc_rate and .set_rate callbacks.
This means when calculating the factors in the .set_rate callback, they
would be off by a factor of the active pre-divider. Same goes for
reading back the clock rate after it is set.
After commit e9afc746299d ("hwrng: geode - Use linux/io.h instead of
asm/io.h") the geode-rng driver uses devres with pci_dev->dev to keep
track of resources, but does not actually register a PCI driver. This
results in the following issues:
1. The driver leaks memory because the driver does not attach to a
device. The driver only uses the PCI device as a reference. devm_*()
functions will release resources on driver detach, which the geode-rng
driver will never do. As a result,
2. The driver cannot be reloaded because there is always a use of the
ioport and region after the first load of the driver.
Revert the changes made by e9afc746299d ("hwrng: geode - Use linux/io.h
instead of asm/io.h").
After commit 31b2a73c9c5f ("hwrng: amd - Migrate to managed API"), the
amd-rng driver uses devres with pci_dev->dev to keep track of resources,
but does not actually register a PCI driver. This results in the
following issues:
1. The message
WARNING: CPU: 2 PID: 621 at drivers/base/dd.c:349 driver_probe_device+0x38c
is output when the i2c_amd756 driver loads and attempts to register a PCI
driver. The PCI & device subsystems assume that no resources have been
registered for the device, and the WARN_ON() triggers since amd-rng has
already do so.
2. The driver leaks memory because the driver does not attach to a
device. The driver only uses the PCI device as a reference. devm_*()
functions will release resources on driver detach, which the amd-rng
driver will never do. As a result,
3. The driver cannot be reloaded because there is always a use of the
ioport and region after the first load of the driver.
Revert the changes made by 31b2a73c9c5f ("hwrng: amd - Migrate to managed
API").
Disabling interrupts for even a millisecond can cause problems for some
devices. That can happen when Intel host controllers wait for the present
state to propagate.
The spin lock is not necessary here. Anything that is racing with changes
to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host.
Although the spin lock probably should be removed from the code paths that
lead to this point, such a patch would touch too much code to be suitable
for stable trees. Consequently, for this patch, just drop the spin lock
while waiting.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Disabling interrupts for even a millisecond can cause problems for some
devices. That can happen when sdhci changes clock frequency because it
waits for the clock to become stable under a spin lock.
The spin lock is not necessary here. Anything that is racing with changes
to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host.
Although the spin lock probably should be removed from the code paths that
lead to this point, such a patch would touch too much code to be suitable
for stable trees. Consequently, for this patch, just drop the spin lock
while waiting.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
sdhci_arasan_get_timeout_clock() divides the frequency it has with (1 <<
(13 + divisor)).
However, the divisor is not some Arasan-specific value, but instead is
just the Data Timeout Counter Value from the SDHCI Timeout Control
Register.
Applying it here like this is wrong as the sdhci driver already takes
that value into account when calculating timeouts, and in fact it *sets*
that register value based on how long a timeout is wanted.
Additionally, sdhci core interprets the .get_timeout_clock callback
return value as if it were read from hardware registers, i.e. the unit
should be kHz or MHz depending on SDHCI_TIMEOUT_CLK_UNIT capability bit.
This bit is set at least on the tested Zynq-7000 SoC.
With the tested hardware (SDHCI_TIMEOUT_CLK_UNIT set) this results in
too high a timeout clock rate being reported, causing the core to use
longer-than-needed timeouts. Additionally, on a partitioned MMC
(therefore having erase_group_def bit set) mmc_calc_max_discard()
disables discard support as it looks like controller does not support
the long timeouts needed for that.
Do not apply the extra divisor and return the timeout clock in the
expected unit.
Tested with a Zynq-7000 SoC and a partitioned Toshiba THGBMAG5A1JBAWR
eMMC card.
The SDHCI controller in the SAMA5D2 chip requires a valid voltage set
in the power control register, otherwise commands will fail with a
timeout error.
When using the regulator framework to specify the regulator used by the
mmc device, the voltage is not configured, and it is not possible to use
the connected device.
Implement a custom 'set_power' function for this specific hardware, that
configures the voltage in the register in all cases.
What started as a rather straightforward race condition reported by
Dmitry using the syzkaller fuzzer ended up revealing some major
problems with how the audit subsystem managed its netlink sockets and
its connection with the userspace audit daemon. Fixing this properly
had quite the cascading effect and what we are left with is this rather
large and complicated patch. My initial goal was to try and decompose
this patch into multiple smaller patches, but the way these changes
are intertwined makes it difficult to split these changes into
meaningful pieces that don't break or somehow make things worse for
the intermediate states.
The patch makes a number of changes, but the most significant are
highlighted below:
* The auditd tracking variables, e.g. audit_sock, are now gone and
replaced by a RCU/spin_lock protected variable auditd_conn which is
a structure containing all of the auditd tracking information.
* We no longer track the auditd sock directly, instead we track it
via the network namespace in which it resides and we use the audit
socket associated with that namespace. In spirit, this is what the
code was trying to do prior to this patch (at least I think that is
what the original authors intended), but it was done rather poorly
and added a layer of obfuscation that only masked the underlying
problems.
* Big backlog queue cleanup, again. In v4.10 we made some pretty big
changes to how the audit backlog queues work, here we haven't changed
the queue design so much as cleaned up the implementation. Brought
about by the locking changes, we've simplified kauditd_thread() quite
a bit by consolidating the queue handling into a new helper function,
kauditd_send_queue(), which allows us to eliminate a lot of very
similar code and makes the looping logic in kauditd_thread() clearer.
* All netlink messages sent to auditd are now sent via
auditd_send_unicast_skb(). Other than just making sense, this makes
the lock handling easier.
* Change the audit_log_start() sleep behavior so that we never sleep
on auditd events (unchanged) or if the caller is holding the
audit_cmd_mutex (changed). Previously we didn't sleep if the caller
was auditd or if the message type fell between a certain range; the
type check was a poor effort of doing what the cmd_mutex check now
does. Richard Guy Briggs originally proposed not sleeping the
cmd_mutex owner several years ago but his patch wasn't acceptable
at the time. At least the idea lives on here.
* A problem with the lost record counter has been resolved. Steve
Grubb and I both happened to notice this problem and according to
some quick testing by Steve, this problem goes back quite some time.
It's largely a harmless problem, although it may have left some
careful sysadmins quite puzzled.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
We concluded there may be a window where the idle wakeup code could get
to pnv_wakeup_tb_loss() (which clobbers non-volatile GPRs), but the
hardware may set SRR1[46:47] to 01b (no state loss) which would result
in the wakeup code failing to restore non-volatile GPRs.
I was not able to trigger this condition with trivial tests on real
hardware or simulator, but the ISA (at least 2.07) seems to allow for
it, and Gautham says that it can happen if there is an exception pending
when the sleep/winkle instruction is executed.
Fixes: 1706567117ba ("powerpc/kvm: make hypervisor state restore a function") Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Acked-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
If ext4_convert_inline_data() was called on a directory with inline
data, the filesystem was left in an inconsistent state (as considered by
e2fsck) because the file size was not increased to cover the new block.
This happened because the inode was not marked dirty after i_disksize
was updated. Fix this by marking the inode dirty at the end of
ext4_finish_convert_inline_dir().
This bug was probably not noticed before because most users mark the
inode dirty afterwards for other reasons. But if userspace executed
FS_IOC_SET_ENCRYPTION_POLICY with invalid parameters, as exercised by
'kvm-xfstests -c adv generic/396', then the inode was never marked dirty
after updating i_disksize.
Fixes: 3c47d54170b6a678875566b1b8d6dcf57904e49b Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Usually every parallel port will have a single pardev registered with
it. But ppdev driver is an exception. This userspace parallel port
driver allows to create multiple parrallel port devices for a single
parallel port. And as a result we were having a big warning like:
"sysfs: cannot create duplicate filename '/devices/parport0/ppdev0.0'".
And with that many parallel port printers stopped working.
We have been using the minor number as the id field while registering
a parralel port device with a parralel port. But when there are
multiple parrallel port device for one single parallel port, they all
tried to register with the same name like 'pardev0.0' and everything
started failing.
Use an incremented index as the id instead of the minor number.
Fixes: 8b7d3a9d903e ("ppdev: use new parport device model")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1414656
Bugzilla: https://bugs.archlinux.org/task/52322 Tested-by: James Feeney <james@nurealm.net> Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Usually every parallel port will have a single pardev registered with
it. But ppdev driver is an exception. This userspace parallel port
driver allows to create multiple parrallel port devices for a single
parallel port. And as a result we were having a nice warning like:
"sysctl table check failed:
/dev/parport/parport0/devices/ppdev0/timeslice Sysctl already exists"
Use the same logic as used in parport_register_device() and register
the proc files only once for each parallel port.
Fixes: 6fa45a226897 ("parport: add device-model to parport subsystem")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1414656
Bugzilla: https://bugs.archlinux.org/task/52322 Tested-by: James Feeney <james@nurealm.net> Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The driver still struggles with firmwares that do not replay to the OS
version request. It is safe not waiting for the replay. First, the driver
doesn't do anything with the replay second the connection is closed
immediately, hence the packet will be just safely discarded in case it
is received and last the driver won't get stuck if the firmware won't
reply.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
This patch fixes 'mei: synchronize irq before initiating a reset'
The patch had introduced a deadlock between irq thread and mei_reset()
as they are both holding the same device lock.
Even if bus is not hot-pluggable, devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
In function _hid_sensor_power_state(), when hid_sensor_read_poll_value()
is called, sensor's all properties will be updated by the value from
sensor hardware/firmware.
In some implementation, sensor hardware/firmware will do a power cycle
during S3. In this case, after resume, once hid_sensor_read_poll_value()
is called, sensor's all properties which are kept by driver during S3
will be changed to default value.
But instead, if a set feature function is called first, sensor
hardware/firmware will be recovered to the last status. So change the
sensor_hub_set_feature() calling order to behind of set feature function
to avoid sensor properties lose.
Signed-off-by: Song Hongyan <hongyan.song@intel.com> Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Use the IS_ENABLED() helper macro to ensure that the configfs group is
initialized either when configfs is built-in or when configfs is built as a
module. Otherwise software device creation will result in undefined
behaviour when configfs is built as a module since the configfs group for
the device not properly initialized.
Similar to commit b2f0c09664b7 ("iio: sw-trigger: Fix config group
initialization").
Fixes: 0f3a8c3f34f7 ("iio: Add support for creating IIO devices via configfs") Reported-by: Miguel Robles <miguel.robles@farole.net> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The tiadc_irq_h(int irq, void *private) function is handling FIFO
overruns by clearing flags, disabling and enabling the ADC to
recover.
If the ADC is running in continuous mode a FIFO overrun happens
regularly. If the disabling of the ADC happens concurrently with
a new conversion. It might happen that the enabling of the ADC
is ignored by the hardware. This stops the ADC permanently. No
more interrupts are triggered.
According to the AM335x Reference Manual (SPRUH73H October 2011 -
Revised April 2013 - Chapter 12.4 and 12.5) it is necessary to
check the ADC FSM bits in REG_ADCFSM before enabling the ADC
again. Because the disabling of the ADC is done right after the
current conversion has been finished.
To trigger this bug it is necessary to run the ADC in continuous
mode. The ADC values of all channels need to be read in an endless
loop. The bug appears within the first 6 hours (~5.4 million
handled FIFO overruns). The user space application will hang on
reading new values from the character device.
Fixes: ca9a563805f7a ("iio: ti_am335x_adc: Add continuous sampling support") Signed-off-by: Michael Engl <michael.engl@wjw-solutions.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
HS400-ES devices fail to initialize with the following error messages.
mmc1: power class selection to bus width 8 ddr 0 failed
mmc1: error -110 whilst initialising MMC card
This was seen on Samsung Chromebook Plus. Code analysis points to
commit 3d4ef329757c ("mmc: core: fix multi-bit bus width without
high-speed mode"), which attempts to set the bus width for all but
HS200 devices unconditionally. However, for HS400-ES, the bus width
is already selected.
Cc: Anssi Hannula <anssi.hannula@bitwise.fi> Cc: Douglas Anderson <dianders@chromium.org> Cc: Brian Norris <briannorris@chromium.org> Fixes: 3d4ef329757c ("mmc: core: fix multi-bit bus width ...") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Shawn Lin <shawn.lin@rock-chip.com> Tested-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Sowmini pointed out Dmitry's RTNL deadlock report to me, and it turns out
to be perfectly accurate - there are various error paths that miss unlock
of the RTNL.
To fix those, change the locking a bit to not be conditional in all those
nl80211_prepare_*_dump() functions, but make those require the RTNL to
start with, and fix the buggy error paths. This also let me use sparse
(by appropriately overriding the rtnl_lock/rtnl_unlock functions) to
validate the changes.
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Make sure to initialise the return value to avoid having allocation
failures going unnoticed when allocating interrupt-endpoint resources.
This prevents use-after-free or worse when the device is later unbound.
Fixes: dbf3e7f654c0 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation.") Cc: Dave Penkler <dpenkler@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
USBTMC devices are required to have a bulk-in and a bulk-out endpoint,
but the driver failed to verify this, something which could lead to the
endpoint addresses being taken from uninitialised memory.
Make sure to zero all private data as part of allocation, and add the
missing endpoint sanity check.
Note that this also addresses a more recently introduced issue, where
the interrupt-in-presence flag would also be uninitialised whenever the
optional interrupt-in endpoint is not present. This in turn could lead
to an interrupt urb being allocated, initialised and submitted based on
uninitialised values.
Fixes: dbf3e7f654c0 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation.") Fixes: 5b775f672cc9 ("USB: add USB test and measurement class driver") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
If usb_get_bos_descriptor() returns an error, usb->bos will be NULL.
Nevertheless, it is dereferenced unconditionally in
hub_set_initial_usb2_lpm_policy() if usb2_hw_lpm_capable is set.
This results in a crash.
The CPPI 4.1 driver polls register to workaround the premature TX
interrupt issue, but it causes audio playback underrun when triggered in
Isoch transfers.
Isoch doesn't do back-to-back transfers, the TX should be done by the
time the next transfer is scheduled. So skip this polling workaround for
Isoch transfer.
Fixes: a655f481d83d6 ("usb: musb: musb_cppi41: handle pre-mature TX complete interrupt") Reported-by: Alexandre Bailon <abailon@baylibre.com> Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Tested-by: Alexandre Bailon <abailon@baylibre.com> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
This specifically fixes the NULL-pointer dereference when probing HWA HC
devices.
Fixes: df3654236e31 ("wusb: add the Wire Adapter (WA) core") Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Cc: David Vrabel <david.vrabel@csr.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Note that the endpoint access that causes the NULL-deref is currently
only used for debugging purposes during probe so the oops only happens
when dynamic debugging is enabled. This means the driver could be
rewritten to continue to accept device with only two endpoints, should
such devices exist.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Some USB 2.0 devices erroneously report millisecond values in
bInterval. The generic config code manages to catch most of them,
but in some cases it's not completely enough.
The case at stake here is a USB 2.0 braille device, which wants to
announce 10ms and thus sets bInterval to 10, but with the USB 2.0
computation that yields to 64ms. It happens that one can type fast
enough to reach this interval and get the device buffers overflown,
leading to problematic latencies. The generic config code does not
catch this case because the 64ms is considered a sane enough value.
This change thus adds a USB_QUIRK_LINEAR_FRAME_INTR_BINTERVAL quirk
to mark devices which actually report milliseconds in bInterval,
and marks Vario Ultra devices as needing it.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The buffer allocation for the firmware data was changed in
commit 43fab9793c1f ("[media] dvb-usb: don't use stack for firmware load")
but the same applies for the reset value.
Fixes: 43fab9793c1f ("[media] dvb-usb: don't use stack for firmware load") Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The streaming_maxburst module parameter is 0 offset (0..15)
so we must add 1 while using it for wBytesPerInterval
calculation for the SuperSpeed companion descriptor.
Without this host uvcvideo driver will always see the wrong
wBytesPerInterval for SuperSpeed uvc gadget and may not find
a suitable video interface endpoint.
e.g. for streaming_maxburst = 0 case it will always
fail as wBytePerInterval was evaluating to 0.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The gadget code exports the bitfield for serial status changes
over the wire in its internal endianness. The fix is to convert
to little endian before sending it over the wire.
Signed-off-by: Oliver Neukum <oneukum@suse.com> Tested-by: 家瑋 <momo1208@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Add Quectel UC15, UC20, EC21, and EC25. The EC20 is handled by
qcserial due to a USB VID/PID conflict with an existing Acer
device.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
A new Dell laptop needs to apply ALC269_FIXUP_DELL1_MIC_NO_PRESENCE to
fix the headset problem, and the pin definiton of this machine is not
in the pin quirk table yet, now adding it to the table.
Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
In the commit [15c75b09f8d1: ALSA: ctxfi: Fallback DMA mask to 32bit],
I forgot to put "!" at dam_set_mask() call check in cthw20k1.c (while
cthw20k2.c is OK). This patch fixes that obvious bug.
(As a side note: although the original commit was completely wrong,
it's still working for most of machines, as it sets to 32bit DMA mask
in the end. So the bug severity is low.)
When snd_seq_pool_done() is called, it marks the closing flag to
refuse the further cell insertions. But snd_seq_pool_done() itself
doesn't clear the cells but just waits until all cells are cleared by
the caller side. That is, it's racy, and this leads to the endless
stall as syzkaller spotted.
This patch addresses the racy by splitting the setup of pool->closing
flag out of snd_seq_pool_done(), and calling it properly before
snd_seq_pool_done().
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory that lie beyond the end of the endpoint
array should a malicious device lack the expected endpoints.
Fixes: bdb5c57f209c ("Input: add sur40 driver for Samsung SUR40... ") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: c04148f915e5 ("Input: add driver for USB VoIP phones with CM109...") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory that lie beyond the end of the endpoint
array should a malicious device lack the expected endpoints.
Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
EeeBook X205TA is yet another ASUS device with a special touchpad
firmware that needs to be accounted for during initialization, or
else the touchpad will go into an invalid state upon suspend/resume.
Adding the appropriate ic_type and product_id check fixes the problem.
Devices identified as E7="73 03 28" use slightly modified version of V8
protocol, with lower count per electrode, different offsets, and different
feature bits in OTP data.
Fixes: aeaa881f9b17 ("Input: ALPS - set DualPoint flag for 74 03 28 devices") Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com> Acked-by: Pali Rohar <pali.rohar@gmail.com> Tested-by: Paul Donohue <linux-kernel@PaulSD.com> Tested-by: Nick Fletcher <nick.m.fletcher@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
When a user connects a DS4 twice using USB and BT, we reject the
second device connection after the setup work. We then perform
a cleanup, but during cleanup we are not removing the touchpad
device. This leads to leakage of an input device, which we would
never remove. It can likely result into a kernel oops as well
when the touchpad evdev node is accessed and the underlaying HID
device has been removed from the system.
[jkosina@suse.cz: added stable annotation] Fixes: ac797b95f532 ("HID: sony: Make the DS4 touchpad a separate device") Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
While playing with mlx4 hardware timestamping of RX packets, I found
that some packets were received by TCP stack with a ~200 ms delay...
Since the timestamp was provided by the NIC, and my probe was added
in tcp_v4_rcv() while in BH handler, I was confident it was not
a sender issue, or a drop in the network.
This would happen with a very low probability, but hurting RPC
workloads.
A NAPI driver normally arms the IRQ after the napi_complete_done(),
after NAPI_STATE_SCHED is cleared, so that the hard irq handler can grab
it.
Problem is that if another point in the stack grabs NAPI_STATE_SCHED bit
while IRQ are not disabled, we might have later an IRQ firing and
finding this bit set, right before napi_complete_done() clears it.
This can happen with busy polling users, or if gro_flush_timeout is
used. But some other uses of napi_schedule() in drivers can cause this
as well.
thread 1 thread 2 (could be on same cpu, or not)
// busy polling or napi_watchdog()
napi_schedule();
...
napi->poll()
device polling:
read 2 packets from ring buffer
Additional 3rd packet is
available.
device hard irq
// does nothing because
NAPI_STATE_SCHED bit is owned by thread 1
napi_schedule();
napi_complete_done(napi, 2);
rearm_irq();
Note that rearm_irq() will not force the device to send an additional
IRQ for the packet it already signaled (3rd packet in my example)
This patch adds a new NAPI_STATE_MISSED bit, that napi_schedule_prep()
can set if it could not grab NAPI_STATE_SCHED
Then napi_complete_done() properly reschedules the napi to make sure
we do not miss something.
Since we manipulate multiple bits at once, use cmpxchg() like in
sk_busy_loop() to provide proper transactions.
In v2, I changed napi_watchdog() to use a relaxed variant of
napi_schedule_prep() : No need to set NAPI_STATE_MISSED from this point.
In v3, I added more details in the changelog and clears
NAPI_STATE_MISSED in busy_poll_stop()
In v4, I added the ideas given by Alexander Duyck in v3 review
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Alexander Duyck <alexander.duyck@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The ECC bit positions that describe whether the ECC interrupt is for
Tx, Rx or descriptor memory and whether the it is a single correctable
or double detected error were defined in incorrectly (reversed order).
Fix the bit position definitions for these settings so that the proper
ECC handling is performed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
icsk_ack.lrcvtime has a 0 value at socket creation time.
tcpi_last_data_recv can have bogus value if no payload is ever received.
This patch initializes icsk_ack.lrcvtime for active sessions
in tcp_finish_connect(), and for passive sessions in
tcp_create_openreq_child()
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Commit 2ae0f17df1cd ("genetlink: use idr to track families") replaced
if (++n < fams_to_skip)
continue;
into:
if (n++ < fams_to_skip)
continue;
This subtle change cause that on retry ctrl_dumpfamily() call we omit
one family that failed to do ctrl_fill_info() on previous call, because
cb->args[0] = n number counts also family that failed to do
ctrl_fill_info().
Patch fixes the problem and avoid confusion in the future just decrease
n counter when ctrl_fill_info() fail.
User visible problem caused by this bug is failure to get access to
some genetlink family i.e. nl80211. However problem is reproducible
only if number of registered genetlink families is big enough to
cause second call of ctrl_dumpfamily().
Cc: Xose Vazquez Perez <xose.vazquez@gmail.com> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: Johannes Berg <johannes@sipsolutions.net> Fixes: 2ae0f17df1cd ("genetlink: use idr to track families") Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
In sk_clone_lock(), we create a new socket and inherit most of the
parent's members via sock_copy() which memcpy()'s various sections.
Now, in case the parent socket had a BPF socket filter attached,
then newsk->sk_filter points to the same instance as the original
sk->sk_filter.
sk_filter_charge() is then called on the newsk->sk_filter to take a
reference and should that fail due to hitting max optmem, we bail
out and release the newsk instance.
The issue is that commit 278571baca2a ("net: filter: simplify socket
charging") wrongly combined the dismantle path with the failure path
of xfrm_sk_clone_policy(). This means, even when charging failed, we
call sk_free_unlock_clone() on the newsk, which then still points to
the same sk_filter as the original sk.
Thus, sk_free_unlock_clone() calls into __sk_destruct() eventually
where it tests for present sk_filter and calls sk_filter_uncharge()
on it, which potentially lets sk_omem_alloc wrap around and releases
the eBPF prog and sk_filter structure from the (still intact) parent.
Fix it by making sure that when sk_filter_charge() failed, we reset
newsk->sk_filter back to NULL before passing to sk_free_unlock_clone(),
so that we don't mess with the parents sk_filter.
Only if xfrm_sk_clone_policy() fails, we did reach the point where
either the parent's filter was NULL and as a result newsk's as well
or where we previously had a successful sk_filter_charge(), thus for
that case, we do need sk_filter_uncharge() to release the prior taken
reference on sk_filter.
Fixes: 278571baca2a ("net: filter: simplify socket charging") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Alexander reported a KMSAN splat caused by reads of uninitialized
field (tb_id_in) from user provided struct fib_result_nl
It turns out nl_fib_input() sanity tests on user input is a bit
wrong :
User can pretend nlh->nlmsg_len is big enough, but provide
at sendmsg() time a too small buffer.
Reported-by: Alexander Potapenko <glider@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Commit 6ac3ce8295e6 ("net: bcmgenet: Remove excessive PHY reset")
removed the bcmgenet_mii_reset() function from bcmgenet_power_up() and
bcmgenet_internal_phy_setup() functions. In so doing it broke the reset
of the internal PHY devices used by the GENETv1-GENETv3 which required
this reset before the UniMAC was enabled. It also broke the internal
GPHY devices used by the GENETv4 because the config_init that installed
the AFE workaround was no longer occurring after the reset of the GPHY
performed by bcmgenet_phy_power_set() in bcmgenet_internal_phy_setup().
In addition the code in bcmgenet_internal_phy_setup() related to the
"enable APD" comment goes with the bcmgenet_mii_reset() so it should
have also been removed.
Commit bd4060a6108b ("net: bcmgenet: Power on integrated GPHY in
bcmgenet_power_up()") moved the bcmgenet_phy_power_set() call to the
bcmgenet_power_up() function, but failed to remove it from the
bcmgenet_internal_phy_setup() function. Had it done so, the
bcmgenet_internal_phy_setup() function would have been empty and could
have been removed at that time.
Commit 5dbebbb44a6a ("net: bcmgenet: Software reset EPHY after power on")
was submitted to correct the functional problems introduced by
commit 6ac3ce8295e6 ("net: bcmgenet: Remove excessive PHY reset"). It
was included in v4.4 and made available on 4.3-stable. Unfortunately,
it didn't fully revert the commit because this bcmgenet_mii_reset()
doesn't apply the soft reset to the internal GPHY used by GENETv4 like
the previous one did. This prevents the restoration of the AFE work-
arounds for internal GPHY devices after the bcmgenet_phy_power_set() in
bcmgenet_internal_phy_setup().
This commit takes the alternate approach of removing the unnecessary
bcmgenet_internal_phy_setup() function which shouldn't have been in v4.3
so that when bcmgenet_mii_reset() was restored it should have only gone
into bcmgenet_power_up(). This will avoid the problems while also
removing the redundancy (and hopefully some of the confusion).
Fixes: 6ac3ce8295e6 ("net: bcmgenet: Remove excessive PHY reset") Signed-off-by: Doug Berger <opendmb@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
In the case udp_sk(sk)->pending is AF_INET6, udpv6_sendmsg() would
jump to do_append_data, skipping the initialization of sockc.tsflags.
Fix the problem by moving sockc.tsflags initialization earlier.
The bug was detected with KMSAN.
Fixes: c14ac9451c34 ("sock: enable timestamping using control messages") Signed-off-by: Alexander Potapenko <glider@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
RX packets statistics ('rx_packets' counter) used to count LRO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.
Note that no information is lost in this patch due to 'rx_lro_packets'
counter existence.
Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets"
rx_packets: 1935066
rx_lro_packets: 35847
rx_packets_phy: 1935066
Fixes: e586b3b0baee ("net/mlx5: Ethernet Datapath files") Signed-off-by: Gal Pressman <galp@mellanox.com> Cc: kernel-team@fb.com Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
TX packets statistics ('tx_packets' counter) used to count GSO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.
Note that no information is lost in this patch due to 'tx_tso_packets'
counter existence.
Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets"
tx_packets: 2451115
tx_tso_packets: 60954
tx_packets_phy: 2451115
Fixes: e586b3b0baee ("net/mlx5: Ethernet Datapath files") Signed-off-by: Gal Pressman <galp@mellanox.com> Cc: kernel-team@fb.com Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
With ConnectX-4 sharing SRQs from the same space as QPs, we hit a
limit preventing some applications to allocate needed QPs amount.
Double the size to 256K.
Fixes: e126ba97dba9e ('mlx5: Add driver for Mellanox Connect-IB adapters') Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The switch cases for the rate limit set and query commands were
missing, which could get us wrong under fw error or driver reset
flow, fix that.
Fixes: 1466cc5b23d1 ('net/mlx5: Rate limit tables support') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
The VRF driver takes a reference to the inet6_dev on the VRF device for
its rt6_local dst when handling local traffic through the VRF device as
a loopback. When the device is deleted the driver does a put on the idev
but does not reset rt6i_idev in the rt6_info struct. When the dst is
destroyed, dst_destroy calls ip6_dst_destroy which does a second put for
what is essentially the same reference causing it to be prematurely freed.
Reset rt6i_idev after the put in the vrf driver.
Fixes: b4869aa2f881e ("net: vrf: ipv6 support for local traffic to
local addresses") Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
This is a Dell branded Sierra Wireless EM7455. It is operating in
MBIM mode by default, but can be configured to provide two QMI/RMNET
functions.
Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Dmitry has reported that a BUG_ON() condition in unix_notinflight()
may be triggered by a simple code that forwards unix socket in an
SCM_RIGHTS message.
That is caused by incorrect unix socket GC implementation in unix_gc().
The GC first collects list of candidates, then (a) decrements their
"children's" inflight counter, (b) checks which inflight counters are
now 0, and then (c) increments all inflight counters back.
(a) and (c) are done by calling scan_children() with inc_inflight or
dec_inflight as the second argument.
Commit 6209344f5a37 ("net: unix: fix inflight counting bug in garbage
collector") changed scan_children() such that it no longer considers
sockets that do not have UNIX_GC_CANDIDATE flag. It also added a block
of code that that unsets this flag _before_ invoking
scan_children(, dec_iflight, ). This may lead to incorrect inflight
counters for some sockets.
This change fixes this bug by changing order of operations:
UNIX_GC_CANDIDATE is now unset only after all inflight counters are
restored to the original state.
Added a case for OVS_TUNNEL_KEY_ATTR_PAD to the switch statement
in ip_tun_from_nlattr in order to prevent the default case
returning an error.
Fixes: b46f6ded906e ("libnl: nla_put_be64(): align on a 64-bit area") Signed-off-by: Kris Murphy <kriskend@linux.vnet.ibm.com> Acked-by: Joe Stringer <joe@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Newer hardware does not provide a cumulative payload length when multiple
descriptors are needed to handle the data. Once the MTU increases beyond
the size that can be handled by a single descriptor, the SKB does not get
built properly by the driver.
The driver will now calculate the size of the data buffers used by the
hardware. The first buffer of the first descriptor is for packet headers
or packet headers and data when the headers can't be split. Subsequent
descriptors in a multi-descriptor chain will not use the first buffer. The
second buffer is used by all the descriptors in the chain for payload data.
Based on whether the driver is processing the first, intermediate, or last
descriptor it can calculate the buffer usage and build the SKB properly.
Tested and verified on both old and new hardware.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
I mistakenly added the code to release sk->sk_frag in
sk_common_release() instead of sk_destruct()
TCP sockets using sk->sk_allocation == GFP_ATOMIC do no call
sk_common_release() at close time, thus leaking one (order-3) page.
iSCSI is using such sockets.
Fixes: 5640f7685831 ("net: use a per task frag allocator") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
When dealing with ipv6 source tunnel key address attribute
(OVS_TUNNEL_KEY_ATTR_IPV6_SRC) we are wrongly setting the tunnel
dst ip, fix that.
Fixes: 6b26ba3a7d95 ('openvswitch: netlink attributes for IPv6 tunneling') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reported-by: Paul Blakey <paulb@mellanox.com> Acked-by: Jiri Benc <jbenc@redhat.com> Acked-by: Joe Stringer <joe@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1676786
In NETDEV_CHANGEUPPER event the upper_info field is valid
only when linking is true. Otherwise it should be ignored.
Fixes: 7907f23adc18 (net/mlx5: Implement RoCE LAG feature) Signed-off-by: Talat Batheesh <talatb@mellanox.com> Reviewed-by: Aviv Heller <avivh@mellanox.com> Reviewed-by: Moni Shoua <monis@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
drivers: hv: Turn off write permission on the hypercall page
BugLink: http://bugs.launchpad.net/bugs/1676635
The hypercall page only needs to be executable but currently it is setup to
be writable as well. Fix the issue.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Cc: <stable@vger.kernel.org> Acked-by: Kees Cook <keescook@chromium.org> Reported-by: Stephen Hemminger <stephen@networkplumber.org> Tested-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 372b1e91343e657a7cc5e2e2bcecd5140ac28119) Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1676635
With TimeSync version 4 protocol support we started updating system time
continuously through the whole lifetime of Hyper-V guests. Every 5 seconds
there is a time sample from the host which triggers do_settimeofday[64]().
While the time from the host is very accurate such adjustments may cause
issues:
- Time is jumping forward and backward, some applications may misbehave.
- In case an NTP server runs in parallel and uses something else for time
sync (network, PTP,...) system time will never converge.
- Systemd starts annoying you by printing "Time has been changed" every 5
seconds to the system log.
Instead of doing in-kernel time adjustments offload the work to an
NTP client by exposing TimeSync messages as a PTP device. Users may now
decide what they want to use as a source.
I tested the solution with chrony, the config was:
refclock PHC /dev/ptp0 poll 3 dpoll -2 offset 0
The result I'm seeing is accurate enough, the time delta between the guest
and the host is almost always within [-10us, +10us], the in-kernel solution
was giving us comparable results.
I also tried implementing PPS device instead of PTP by using not currently
used Hyper-V synthetic timers (we use only one of four for clockevent) but
with PPS source only chrony wasn't able to give me the required accuracy,
the delta often more that 100us.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 3716a49a81ba19dda7202633a68b28564ba95eb5) Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1676635
As a preparation to implementing Hyper-V PTP device supporting
.getcrosststamp we need to export a reference to the current Hyper-V
clocksource in use (MSR or TSC page).
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit dee863b571b0a76e9c549ee99e8782bb4bc6502b) Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Fixes: 352c9624242d ("Drivers: hv: vmbus: Move the definition of generate_guest_id()") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 9b06e1018abc65585b07c75c5b3f406dbabe7005) Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Alex Ng <alexng@messages.microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 1274a690f6b2bd2b37447c47e3062afa8aa43f93) Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Alex Ng [Sat, 28 Jan 2017 19:37:17 +0000 (12:37 -0700)]
Drivers: hv: vmbus: Use all supported IC versions to negotiate
BugLink: http://bugs.launchpad.net/bugs/1676635
Previously, we were assuming that each IC protocol version was tied to a
specific host version. For example, some Windows 10 preview hosts only
support v3 TimeSync even though driver assumes v4 is supported by all
Windows 10 hosts.
The guest will stop trying to negotiate even though older supported
versions may still be offered by the host.
Make IC version negotiation more robust by going through all versions
that are supported by the guest.
Fixes: 3da0401b4d0e ("Drivers: hv: utils: Fix the mapping between host
version and protocol to use")
Reported-by: Rolf Neugebauer <rolf.neugebauer@docker.com> Signed-off-by: Alex Ng <alexng@messages.microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit a1656454131880980bc3a5313c8bf66ef5990c91) Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Vitaly Kuznetsov [Sat, 28 Jan 2017 19:37:16 +0000 (12:37 -0700)]
Drivers: hv: balloon: add a fall through comment to hv_memory_notifier()
BugLink: http://bugs.launchpad.net/bugs/1676635
Coverity scan gives a warning when there is fall through in a switch
without a comment. This fall through is intentional as ol_waitevent needs
to be completed to unblock hv_mem_hot_add() allowing it to process next
requests regardless of the result of if we were able to online this block.
Reported-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit ad6d41253bf91eabb41626683c35a712ba27a20c) Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Vitaly Kuznetsov [Sat, 28 Jan 2017 19:37:15 +0000 (12:37 -0700)]
Drivers: hv: restore TSC page cleanup before kexec
BugLink: http://bugs.launchpad.net/bugs/1676635
We need to cleanup the TSC page before doing kexec/kdump or the new kernel
may crash if it tries to use it.
Fixes: 63ed4e0c67df ("Drivers: hv: vmbus: Consolidate all Hyper-V specific clocksource code") Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 5647dbf8f0807a35421bd0232247b02413ef2cab) Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Vitaly Kuznetsov [Sat, 28 Jan 2017 19:37:14 +0000 (12:37 -0700)]
Drivers: hv: restore hypervcall page cleanup before kexec
BugLink: http://bugs.launchpad.net/bugs/1676635
We need to cleanup the hypercall page before doing kexec/kdump or the new
kernel may crash if it tries to use it. Reuse the now-empty hv_cleanup
function renaming it to hyperv_cleanup and moving to the arch specific
code.
Fixes: 8730046c1498 ("Drivers: hv vmbus: Move Hypercall page setup out of common code") Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit d6f3609d2b4c6d0eec01f398cb685e50da3e6013) Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Acked-by: John Stultz <john.stultz@linaro.org> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 17244623a4c0f68d3f02c9c74d9b6ae259425826) Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 8e27a236312c4ab6dc8dbd303552b771d3569cf1) Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 37e11d5c7052a5ca55ef807731c75218ea341b4c) Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
K. Y. Srinivasan [Thu, 19 Jan 2017 18:51:57 +0000 (11:51 -0700)]
Drivers: hv: vmbus: Define an API to retrieve virtual processor index
BugLink: http://bugs.launchpad.net/bugs/1676635
As part of cleaning up architecture specific code, define an API
to retrieve the virtual procesor index.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 7297ff0ca9db7e2d830841035b95d8b94b529142) Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
K. Y. Srinivasan [Thu, 19 Jan 2017 18:51:56 +0000 (11:51 -0700)]
Drivers: hv: vmbus: Define APIs to manipulate the synthetic interrupt controller
BugLink: http://bugs.launchpad.net/bugs/1676635
As part of cleaning up architecture specific code, define APIs
to manipulate the interrupt controller state.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 06d1d98a839f196e94cb726008fb2118e430f356) Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 8e307bf82d76ab02e95a00d132d926f04db6ccab) Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 155e4a2f28a59e5344dfa7c5d003161fe59a5bf2) Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
projects / mirror_ubuntu-zesty-kernel.git / log