Recently while investigating a problem with rr and signals I noticed
that siglock is dropped in ptrace_signal and get_signal does not jump
to relock.
Looking farther to see if the problem is anywhere else I see that
do_signal_stop also returns if signal_group_exit is true. I believe
that test can now never be true, but it is a bit hard to trace
through and be certain.
Testing signal_group_exit is not expensive, so move the test for
signal_group_exit into the for loop inside of get_signal to ensure
the test is never skipped improperly.
This has been a potential problem since I added the test for
signal_group_exit was added.
Fixes: 35634ffa1751 ("signal: Always notice exiting tasks") Reviewed-by: Kees Cook <keescook@chromium.org> Link: https://lkml.kernel.org/r/875yssekcd.fsf_-_@email.froward.int.ebiederm.org Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
As it was before the blamed commit, s3an_nor_scan() was called
after mtd size was set with params->size, and it overwrote the mtd
size value with '8 * nor->page_size * nor->info->n_sectors' when
XSR_PAGESIZE was set. With the introduction of
s3an_post_sfdp_fixups(), we missed to update the mtd size for the
s3an flashes. Fix the mtd size by updating both nor->params->size,
(which will update the mtd_info size later on) and nor->mtd.size
(which is used in spi_nor_set_addr_width()).
The Linux NFS server currently responds to a zero-length NFSv3 WRITE
request with NFS3ERR_IO. It responds to a zero-length NFSv4 WRITE
with NFS4_OK and count of zero.
RFC 1813 says of the WRITE procedure's @count argument:
count
The number of bytes of data to be written. If count is
0, the WRITE will succeed and return a count of 0,
barring errors due to permissions checking.
RFC 8881 has similar language for NFSv4, though NFSv4 removed the
explicit @count argument because that value is already contained in
the opaque payload array.
The synthetic client pynfs's WRT4 and WRT15 tests do emit zero-
length WRITEs to exercise this spec requirement. Commit fdec6114ee1f
("nfsd4: zero-length WRITE should succeed") addressed the same
problem there with the same fix.
But interestingly the Linux NFS client does not appear to emit zero-
length WRITEs, instead squelching them. I'm not aware of a test that
can generate such WRITEs for NFSv3, so I wrote a naive C program to
generate a zero-length WRITE and test this fix.
Fixes: 8154ef2776aa ("NFSD: Clean up legacy NFS WRITE argument XDR decoders") Reported-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Cc: stable@vger.kernel.org Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Now that the NFSv2 and NFSv3 XDR decoders have been converted to
use xdr_streams, the WRITE decoder functions can use
xdr_stream_subsegment() to extract the WRITE payload into its own
xdr_buf, just as the NFSv4 WRITE XDR decoder currently does.
That makes it possible to pass the first kvec, pages array + length,
page_base, and total payload length via a single function parameter.
The payload's page_base is not yet assigned or used, but will be in
subsequent patches.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
While investigating on why a synchronize_net() has been added recently
in ipv6_mc_down(), I found that igmp6_event_query() and igmp6_event_report()
might drop skbs in some cases.
Discussion about removing synchronize_net() from ipv6_mc_down()
will happen in a different thread.
Fixes: f185de28d9ae ("mld: add new workqueues for process mld events") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Taehee Yoo <ap420073@gmail.com> Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20220303173728.937869-1-eric.dumazet@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Since referencing user space pointers is special, if the user wants to
filter on a field that is a pointer to user space, then they need to
specify it.
Add a ".ustring" attribute to the field name for filters to state that the
field is pointing to user space such that the kernel can take the
appropriate action to read that pointer.
Link: https://lore.kernel.org/all/yt9d8rvmt2jq.fsf@linux.ibm.com/ Fixes: 77360f9bbc7e ("tracing: Add test for user space strings when filtering on string pointers") Tested-by: Sven Schnelle <svens@linux.ibm.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Workstation application ANSA/META v21.1.4 get this error dmesg when
running CI test suite provided by ANSA/META:
[drm:amdgpu_gem_va_ioctl [amdgpu]] *ERROR* Couldn't update BO_VA (-16)
This is caused by:
1. create a 256MB buffer in invisible VRAM
2. CPU map the buffer and access it causes vm_fault and try to move
it to visible VRAM
3. force visible VRAM space and traverse all VRAM bos to check if
evicting this bo is valuable
4. when checking a VM bo (in invisible VRAM), amdgpu_vm_evictable()
will set amdgpu_vm->evicting, but latter due to not in visible
VRAM, won't really evict it so not add it to amdgpu_vm->evicted
5. before next CS to clear the amdgpu_vm->evicting, user VM ops
ioctl will pass amdgpu_vm_ready() (check amdgpu_vm->evicted)
but fail in amdgpu_vm_bo_update_mapping() (check
amdgpu_vm->evicting) and get this error log
This error won't affect functionality as next CS will finish the
waiting VM ops. But we'd better clear the error log by checking
the amdgpu_vm->evicting flag in amdgpu_vm_ready() to stop calling
amdgpu_vm_bo_update_mapping() later.
Another reason is amdgpu_vm->evicted list holds all BOs (both
user buffer and page table), but only page table BOs' eviction
prevent VM ops. amdgpu_vm->evicting flag is set only for page
table BOs, so we should use evicting flag instead of evicted list
in amdgpu_vm_ready().
The side effect of this change is: previously blocked VM op (user
buffer in "evicted" list but no page table in it) gets done
immediately.
v2: update commit comments.
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Qiang Yu <qiang.yu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The f_CNT register (at the PCI config. address 0x78) is 16-bit, not
8-bit! The bug was there from the very start... :-(
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Fixes: 669a5db411d8 ("[libata] Add a bunch of PATA drivers.") Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Syzbot found a GPF in reweight_entity. This has been bisected to
commit 4ef0c5c6b5ba ("kernel/sched: Fix sched_fork() access an invalid
sched_task_group")
There is a race between sched_post_fork() and setpriority(PRIO_PGRP)
within a thread group that causes a null-ptr-deref in
reweight_entity() in CFS. The scenario is that the main process spawns
number of new threads, which then call setpriority(PRIO_PGRP, 0, -20),
wait, and exit. For each of the new threads the copy_process() gets
invoked, which adds the new task_struct and calls sched_post_fork()
for it.
In the above scenario there is a possibility that
setpriority(PRIO_PGRP) and set_one_prio() will be called for a thread
in the group that is just being created by copy_process(), and for
which the sched_post_fork() has not been executed yet. This will
trigger a null pointer dereference in reweight_entity(), as it will
try to access the run queue pointer, which hasn't been set.
Before the mentioned change the cfs_rq pointer for the task has been
set in sched_fork(), which is called much earlier in copy_process(),
before the new task is added to the thread_group. Now it is done in
the sched_post_fork(), which is called after that. To fix the issue
the remove the update_load param from the update_load param() function
and call reweight_task() only if the task flag doesn't have the
TASK_NEW flag set.
Fixes: 4ef0c5c6b5ba ("kernel/sched: Fix sched_fork() access an invalid sched_task_group") Reported-by: syzbot+af7a719bc92395ee41b3@syzkaller.appspotmail.com Signed-off-by: Tadeusz Struk <tadeusz.struk@linaro.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20220203161846.1160750-1-tadeusz.struk@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
in the follow scenario:
1. jbd start transaction n
2. task A get new handle for transaction n+1
3. task A do some actions and add inode to FC_Q_MAIN fc_q
4. jbd complete transaction n and clear FC_Q_MAIN fc_q
5. task A call fsync
Fast commit will lost the file actions during a full commit.
we should also add updates to staging queue during a full commit.
and in ext4_fc_cleanup(), when reset a inode's fc track range, check
it's i_sync_tid, if it bigger than current transaction tid, do not
rest it, or we will lost the track range.
And EXT4_MF_FC_COMMITTING is not needed anymore, so drop it.
Signed-off-by: Xin Yin <yinxin.x@bytedance.com> Link: https://lore.kernel.org/r/20220117093655.35160-3-yinxin.x@bytedance.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: stable@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
For the follow scenario:
1. jbd start commit transaction n
2. task A get new handle for transaction n+1
3. task A do some ineligible actions and mark FC_INELIGIBLE
4. jbd complete transaction n and clean FC_INELIGIBLE
5. task A call fsync
In this case fast commit will not fallback to full commit and
transaction n+1 also not handled by jbd.
Make ext4_fc_mark_ineligible() also record transaction tid for
latest ineligible case, when call ext4_fc_cleanup() check
current transaction tid, if small than latest ineligible tid
do not clear the EXT4_MF_FC_INELIGIBLE.
Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Reported-by: Ritesh Harjani <riteshh@linux.ibm.com> Suggested-by: Harshad Shirwadkar <harshadshirwadkar@gmail.com> Signed-off-by: Xin Yin <yinxin.x@bytedance.com> Link: https://lore.kernel.org/r/20220117093655.35160-2-yinxin.x@bytedance.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: stable@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
This patch drops ext4_fc_start_ineligible() and
ext4_fc_stop_ineligible() APIs. Fast commit ineligible transactions
should simply call ext4_fc_mark_ineligible() after starting the
trasaction.
Signed-off-by: Harshad Shirwadkar <harshadshirwadkar@gmail.com> Link: https://lore.kernel.org/r/20211223202140.2061101-3-harshads@google.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
When sending x_char in stm32_usart_transmit_chars(), driver can overwrite
the value of TDR register by the value of x_char. If this happens, the
previous value that was present in TDR register will not be sent through
uart.
This code checks if the previous value in TDR register is sent before
writing the x_char value into register.
Mark the start_backtrace() as notrace and NOKPROBE_SYMBOL
because this function is called from ftrace and lockdep to
get the caller address via return_address(). The lockdep
is used in kprobes, it should also be NOKPROBE_SYMBOL.
Fixes: b07f3499661c ("arm64: stacktrace: Move start_backtrace() out of the header") Cc: <stable@vger.kernel.org> # 5.13.x Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Reviewed-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/164301227374.1433152.12808232644267107415.stgit@devnote2 Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The reason is that trace event filter treats the user space pointer
defined by "filename" as a normal pointer to compare against the "cpu"
string. The following bug happened:
The above happened because the kernel tried to access user space directly
and triggered a "supervisor read access in kernel mode" fault. Worse yet,
the memory could not even be loaded yet, and a SEGFAULT could happen as
well. This could be true for kernel space accessing as well.
To be even more robust, test both kernel and user space strings. If the
string fails to read, then simply have the filter fail.
Note, TASK_SIZE is used to determine if the pointer is user or kernel space
and the appropriate strncpy_from_kernel/user_nofault() function is used to
copy the memory. For some architectures, the compare to TASK_SIZE may always
pick user space or kernel space. If it gets it wrong, the only thing is that
the filter will fail to match. In the future, this needs to be fixed to have
the event denote which should be used. But failing a filter is much better
than panicing the machine, and that can be solved later.
Link: https://lore.kernel.org/all/20220107044951.22080-1-kernelfans@gmail.com/ Link: https://lkml.kernel.org/r/20220110115532.536088fd@gandalf.local.home Cc: stable@vger.kernel.org Cc: Ingo Molnar <mingo@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Tom Zanussi <zanussi@kernel.org> Reported-by: Pingfan Liu <kernelfans@gmail.com> Tested-by: Pingfan Liu <kernelfans@gmail.com> Fixes: 87a342f5db69d ("tracing/filters: Support filtering for char * strings") Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
In exfat_truncate(), the computation of inode->i_blocks is wrong if
the file is larger than 4 GiB because a 32-bit variable is used as a
mask. This is fixed and simplified by using round_up().
Also fix the same buggy computation in exfat_read_root() and another
(correct) one in exfat_fill_inode(). The latter was fixed another way
last month but can be simplified by using round_up() as well. See:
commit 0c336d6e33f4 ("exfat: fix incorrect loading of i_blocks for
large files")
Fixes: 98d917047e8b ("exfat: add file operations") Cc: stable@vger.kernel.org # v5.7+ Suggested-by: Matthew Wilcox <willy@infradead.org> Reviewed-by: Sungjong Seo <sj1557.seo@samsung.com> Signed-off-by: Christophe Vu-Brugier <christophe.vu-brugier@seagate.com> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Add quirk CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE for Telit FN990
0x1071 composition in order to avoid bind error.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Driver builds fine with COMPILE_TEST. Enable it for wider test coverage
and easier maintenance.
Signed-off-by: Wolfram Sang <wsa@kernel.org> Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
pm_runtime_get_() increments the runtime PM usage counter even
when it returns an error code, thus a matching decrement is needed on
the error handling path to keep the counter balanced.
Correct the UMD pstate profiling clocks for Dimgrey Cavefish and Beige
Goby.
Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
seccomp_bpf failed on tests 47 global.user_notification_filter_empty
and 48 global.user_notification_filter_empty_threaded when it's
tested on updated kernel but with old kernel headers. Because old
kernel headers don't have definition of macro __NR_clone3 which is
required for these two tests. Since under selftests/, we can install
headers once for all tests (the default INSTALL_HDR_PATH is
usr/include), fix it by adding usr/include to the list of directories
to be searched. Use "-isystem" to indicate it's a system directory as
the real kernel headers directories are.
Signed-off-by: Sherry Yang <sherry.yang@oracle.com> Tested-by: Sherry Yang <sherry.yang@oracle.com> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
When we create a file with modefromsids we set an ACL that
has one ACE for the magic modefromsid as well as a second ACE that
grants full access to all authenticated users.
When later we chante the mode on the file we strip away this, and other,
ACE for authenticated users in set_chmod_dacl() and then just add back/update
the modefromsid ACE.
Thus leaving the file with a single ACE that is for the mode and no ACE
to grant any user any rights to access the file.
Fix this by always adding back also the modefromsid ACE so that we do not
drop the rights to access the file.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
When cifs_get_root() fails during cifs_smb3_do_mount() we call
deactivate_locked_super() which eventually will call delayed_free() which
will free the context.
In this situation we should not proceed to enter the out: section in
cifs_smb3_do_mount() and free the same resources a second time.
[Thu Feb 10 12:59:06 2022] BUG: KASAN: use-after-free in rcu_cblist_dequeue+0x32/0x60
[Thu Feb 10 12:59:06 2022] Read of size 8 at addr ffff888364f4d110 by task swapper/1/0
[Thu Feb 10 12:59:06 2022] CPU: 1 PID: 0 Comm: swapper/1 Tainted: G OE 5.17.0-rc3+ #4
[Thu Feb 10 12:59:06 2022] Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v4.0 12/17/2019
[Thu Feb 10 12:59:06 2022] Call Trace:
[Thu Feb 10 12:59:06 2022] <IRQ>
[Thu Feb 10 12:59:06 2022] dump_stack_lvl+0x5d/0x78
[Thu Feb 10 12:59:06 2022] print_address_description.constprop.0+0x24/0x150
[Thu Feb 10 12:59:06 2022] ? rcu_cblist_dequeue+0x32/0x60
[Thu Feb 10 12:59:06 2022] kasan_report.cold+0x7d/0x117
[Thu Feb 10 12:59:06 2022] ? rcu_cblist_dequeue+0x32/0x60
[Thu Feb 10 12:59:06 2022] __asan_load8+0x86/0xa0
[Thu Feb 10 12:59:06 2022] rcu_cblist_dequeue+0x32/0x60
[Thu Feb 10 12:59:06 2022] rcu_core+0x547/0xca0
[Thu Feb 10 12:59:06 2022] ? call_rcu+0x3c0/0x3c0
[Thu Feb 10 12:59:06 2022] ? __this_cpu_preempt_check+0x13/0x20
[Thu Feb 10 12:59:06 2022] ? lock_is_held_type+0xea/0x140
[Thu Feb 10 12:59:06 2022] rcu_core_si+0xe/0x10
[Thu Feb 10 12:59:06 2022] __do_softirq+0x1d4/0x67b
[Thu Feb 10 12:59:06 2022] __irq_exit_rcu+0x100/0x150
[Thu Feb 10 12:59:06 2022] irq_exit_rcu+0xe/0x30
[Thu Feb 10 12:59:06 2022] sysvec_hyperv_stimer0+0x9d/0xc0
...
[Thu Feb 10 12:59:07 2022] Freed by task 58179:
[Thu Feb 10 12:59:07 2022] kasan_save_stack+0x26/0x50
[Thu Feb 10 12:59:07 2022] kasan_set_track+0x25/0x30
[Thu Feb 10 12:59:07 2022] kasan_set_free_info+0x24/0x40
[Thu Feb 10 12:59:07 2022] ____kasan_slab_free+0x137/0x170
[Thu Feb 10 12:59:07 2022] __kasan_slab_free+0x12/0x20
[Thu Feb 10 12:59:07 2022] slab_free_freelist_hook+0xb3/0x1d0
[Thu Feb 10 12:59:07 2022] kfree+0xcd/0x520
[Thu Feb 10 12:59:07 2022] cifs_smb3_do_mount+0x149/0xbe0 [cifs]
[Thu Feb 10 12:59:07 2022] smb3_get_tree+0x1a0/0x2e0 [cifs]
[Thu Feb 10 12:59:07 2022] vfs_get_tree+0x52/0x140
[Thu Feb 10 12:59:07 2022] path_mount+0x635/0x10c0
[Thu Feb 10 12:59:07 2022] __x64_sys_mount+0x1bf/0x210
[Thu Feb 10 12:59:07 2022] do_syscall_64+0x5c/0xc0
[Thu Feb 10 12:59:07 2022] entry_SYSCALL_64_after_hwframe+0x44/0xae
[Thu Feb 10 12:59:07 2022] Last potentially related work creation:
[Thu Feb 10 12:59:07 2022] kasan_save_stack+0x26/0x50
[Thu Feb 10 12:59:07 2022] __kasan_record_aux_stack+0xb6/0xc0
[Thu Feb 10 12:59:07 2022] kasan_record_aux_stack_noalloc+0xb/0x10
[Thu Feb 10 12:59:07 2022] call_rcu+0x76/0x3c0
[Thu Feb 10 12:59:07 2022] cifs_umount+0xce/0xe0 [cifs]
[Thu Feb 10 12:59:07 2022] cifs_kill_sb+0xc8/0xe0 [cifs]
[Thu Feb 10 12:59:07 2022] deactivate_locked_super+0x5d/0xd0
[Thu Feb 10 12:59:07 2022] cifs_smb3_do_mount+0xab9/0xbe0 [cifs]
[Thu Feb 10 12:59:07 2022] smb3_get_tree+0x1a0/0x2e0 [cifs]
[Thu Feb 10 12:59:07 2022] vfs_get_tree+0x52/0x140
[Thu Feb 10 12:59:07 2022] path_mount+0x635/0x10c0
[Thu Feb 10 12:59:07 2022] __x64_sys_mount+0x1bf/0x210
[Thu Feb 10 12:59:07 2022] do_syscall_64+0x5c/0xc0
[Thu Feb 10 12:59:07 2022] entry_SYSCALL_64_after_hwframe+0x44/0xae
Reported-by: Shyam Prasad N <sprasad@microsoft.com> Reviewed-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
When idsfromsid is used we create a special SID for owner/group.
This structure must be initialized or else the first 5 bytes
of the Authority field of the SID will contain uninitialized data
and thus not be a valid SID.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
msg_data_sz return a 32bit value, but size is 16bit. This may lead to a
bit overflow.
Signed-off-by: Hangyu Hua <hbh25y@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
If backing file's filesystem has implemented ->fallocate(), we think the
loop device can support discard, then pass sb->s_blocksize as
discard_granularity. However, some underlying FS, such as overlayfs,
doesn't set sb->s_blocksize, and causes discard_granularity to be set as
zero, then the warning in __blkdev_issue_discard() is triggered.
Christoph suggested to pass kstatfs.f_bsize as discard granularity, and
this way is fine because kstatfs.f_bsize means 'Optimal transfer block
size', which still matches with definition of discard granularity.
So fix the issue by setting discard_granularity as kstatfs.f_bsize if it
is available, otherwise claims discard isn't supported.
Cc: Christoph Hellwig <hch@lst.de> Cc: Vivek Goyal <vgoyal@redhat.com> Reported-by: Pei Zhang <pezhang@redhat.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20220126035830.296465-1-ming.lei@redhat.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
It appears that a read access to GIC[DR]_I[CS]PENDRn doesn't always
result in the pending interrupts being accurately reported if they are
mapped to a HW interrupt. This is particularily visible when acking
the timer interrupt and reading the GICR_ISPENDR1 register immediately
after, for example (the interrupt appears as not-pending while it really
is...).
This is because a HW interrupt has its 'active and pending state' kept
in the *physical* distributor, and not in the virtual one, as mandated
by the spec (this is what allows the direct deactivation). The virtual
distributor only caries the pending and active *states* (note the
plural, as these are two independent and non-overlapping states).
Fix it by reading the HW state back, either from the timer itself or
from the distributor if necessary.
Reported-by: Ricardo Koller <ricarkol@google.com> Tested-by: Ricardo Koller <ricarkol@google.com> Reviewed-by: Ricardo Koller <ricarkol@google.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20220208123726.3604198-1-maz@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
This is because we started using writeback_inodes_sb() to flush delalloc
when committing a transaction (when using -o flushoncommit), in order to
avoid deadlocks with filesystem freeze operations. This change was made
by commit ce8ea7cc6eb313 ("btrfs: don't call btrfs_start_delalloc_roots
in flushoncommit"). After that change we started producing that warning,
and every now and then a user reports this since the warning happens too
often, it spams dmesg/syslog, and a user is unsure if this reflects any
problem that might compromise the filesystem's reliability.
We can not just lock the sb->s_umount semaphore before calling
writeback_inodes_sb(), because that would at least deadlock with
filesystem freezing, since at fs/super.c:freeze_super() sync_filesystem()
is called while we are holding that semaphore in write mode, and that can
trigger a transaction commit, resulting in a deadlock. It would also
trigger the same type of deadlock in the unmount path. Possibly, it could
also introduce some other locking dependencies that lockdep would report.
To fix this call try_to_writeback_inodes_sb() instead of
writeback_inodes_sb(), because that will try to read lock sb->s_umount
and then will only call writeback_inodes_sb() if it was able to lock it.
This is fine because the cases where it can't read lock sb->s_umount
are during a filesystem unmount or during a filesystem freeze - in those
cases sb->s_umount is write locked and sync_filesystem() is called, which
calls writeback_inodes_sb(). In other words, in all cases where we can't
take a read lock on sb->s_umount, writeback is already being triggered
elsewhere.
An alternative would be to call btrfs_start_delalloc_roots() with a
number of pages different from LONG_MAX, for example matching the number
of delalloc bytes we currently have, in which case we would end up
starting all delalloc with filemap_fdatawrite_wbc() and not with an
async flush via filemap_flush() - that is only possible after the rather
recent commit e076ab2a2ca70a ("btrfs: shrink delalloc pages instead of
full inodes"). However that creates a whole new can of worms due to new
lock dependencies, which lockdep complains, like for example:
[ 8948.247280] ======================================================
[ 8948.247823] WARNING: possible circular locking dependency detected
[ 8948.248353] 5.17.0-rc1-btrfs-next-111 #1 Not tainted
[ 8948.248786] ------------------------------------------------------
[ 8948.249320] kworker/u16:18/933570 is trying to acquire lock:
[ 8948.249812] ffff9b3de1591690 (sb_internal#2){.+.+}-{0:0}, at: find_free_extent+0x141e/0x1590 [btrfs]
[ 8948.250638]
but task is already holding lock:
[ 8948.251140] ffff9b3e09c717d8 (&root->delalloc_mutex){+.+.}-{3:3}, at: start_delalloc_inodes+0x78/0x400 [btrfs]
[ 8948.252018]
which lock already depends on the new lock.
It all comes from the fact that btrfs_start_delalloc_roots() takes the
delalloc_root_mutex, in the transaction commit path we are holding a
read lock on one of the superblock's freeze semaphores (via
sb_start_intwrite()), the async reclaim task can also do a call to
btrfs_start_delalloc_roots(), which ends up triggering writeback with
calls to filemap_fdatawrite_wbc(), resulting in extent allocation which
in turn can call btrfs_start_transaction(), which will result in taking
the freeze semaphore via sb_start_intwrite(), forming a nasty dependency
on all those locks which can be taken in different orders by different
code paths.
So just adopt the simple approach of calling try_to_writeback_inodes_sb()
at btrfs_start_delalloc_flush().
Buttonpads are expected to map the INPUT_PROP_BUTTONPAD property bit
and the BTN_LEFT key bit.
As explained in the specification, where a device has a button type
value of 0 (click-pad) or 1 (pressure-pad) there should not be
discrete buttons:
https://docs.microsoft.com/en-us/windows-hardware/design/component-guidelines/touchpad-windows-precision-touchpad-collection#device-capabilities-feature-report
However, some drivers map the BTN_RIGHT and/or BTN_MIDDLE key bits even
though the device is a buttonpad and therefore does not have those
buttons.
This behavior has forced userspace applications like libinput to
implement different workarounds and quirks to detect buttonpads and
offer to the user the right set of features and configuration options.
For more information:
https://gitlab.freedesktop.org/libinput/libinput/-/merge_requests/726
In order to avoid this issue clear the BTN_RIGHT and BTN_MIDDLE key
bits when the input device is register if the INPUT_PROP_BUTTONPAD
property bit is set.
Notice that this change will not affect udev because it does not check
for buttons. See systemd/src/udev/udev-builtin-input_id.c.
List of known affected hardware:
- Chuwi AeroBook Plus
- Chuwi Gemibook
- Framework Laptop
- GPD Win Max
- Huawei MateBook 2020
- Prestigio Smartbook 141 C2
- Purism Librem 14v1
- StarLite Mk II - AMI firmware
- StarLite Mk II - Coreboot firmware
- StarLite Mk III - AMI firmware
- StarLite Mk III - Coreboot firmware
- StarLabTop Mk IV - AMI firmware
- StarLabTop Mk IV - Coreboot firmware
- StarBook Mk V
Acked-by: Peter Hutterer <peter.hutterer@who-t.net> Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Acked-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: José Expósito <jose.exposito89@gmail.com> Link: https://lore.kernel.org/r/20220208174806.17183-1-jose.exposito89@gmail.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The check done by regulator_late_cleanup() to detect whether a regulator
is on was inconsistent with the check done by _regulator_is_enabled().
While _regulator_is_enabled() takes the enable GPIO into account,
regulator_late_cleanup() was not doing that.
This resulted in a false positive, e.g. when a GPIO-controlled fixed
regulator was used, which was not enabled at boot time, e.g.
Such regulator doesn't have an is_enabled() operation. Nevertheless
it's state can be determined based on the enable GPIO. The check in
regulator_late_cleanup() wrongly assumed that the regulator is on and
tried to disable it.
Signed-off-by: Oliver Barta <oliver.barta@aptiv.com> Link: https://lore.kernel.org/r/20220208084645.8686-1-oliver.barta@aptiv.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The current rt5682_jack_detect_handler() assumes the component
and card will always show up and implements an infinite usleep
loop waiting for them to show up.
This does not hold true if a codec interrupt (or other
event) occurs when the card is unbound. The codec driver's
remove or shutdown functions cannot cancel the workqueue due
to the wait loop. As a result, code can either end up blocking
the workqueue, or hit a kernel oops when the card is freed.
Fix the issue by rescheduling the jack detect handler in
case the card is not ready. In case card never shows up,
the shutdown/remove/suspend calls can now cancel the detect
task.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Shuming Fan <shumingf@realtek.com> Link: https://lore.kernel.org/r/20220207153000.3452802-3-kai.vehmanen@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The current rt5668_jack_detect_handler() assumes the component
and card will always show up and implements an infinite usleep
loop waiting for them to show up.
This does not hold true if a codec interrupt (or other
event) occurs when the card is unbound. The codec driver's
remove or shutdown functions cannot cancel the workqueue due
to the wait loop. As a result, code can either end up blocking
the workqueue, or hit a kernel oops when the card is freed.
Fix the issue by rescheduling the jack detect handler in
case the card is not ready. In case card never shows up,
the shutdown/remove/suspend calls can now cancel the detect
task.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Shuming Fan <shumingf@realtek.com> Link: https://lore.kernel.org/r/20220207153000.3452802-2-kai.vehmanen@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The CLKT register contains at poweron 0x40, which at our typical 100kHz
bus rate means .64ms. But there is no specified limit to how long devices
should be able to stretch the clocks, so just disable the timeout. We
still have a timeout wrapping the entire transfer.
Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> BugLink: https://github.com/raspberrypi/linux/issues/3064 Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
In mac80211_hwsim, the probe_req frame is created and sent while
scanning. It is sent with ieee80211_tx_info which is not initialized.
Uninitialized ieee80211_tx_info can cause problems when using
mac80211_hwsim with wmediumd. wmediumd checks the tx_rates field of
ieee80211_tx_info and doesn't relay probe_req frame to other clients
even if it is a broadcasting message.
Call ieee80211_tx_prepare_skb() to initialize ieee80211_tx_info for
the probe_req that is created by hw_scan_work in mac80211_hwsim.
Signed-off-by: JaeMan Park <jaeman@google.com> Link: https://lore.kernel.org/r/20220113060235.546107-1-jaeman@google.com
[fix memory leak] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
(cherry picked from commit ce05b997426df4c5321358e369f1f32f257c57a9) Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Mika Westerberg [Tue, 8 Mar 2022 08:49:08 +0000 (16:49 +0800)]
thunderbolt: Do not program path HopIDs for USB4 routers
BugLink: https://bugs.launchpad.net/bugs/1955016
These fields are marked read-only for USB4 routers so do not touch them
in that case. Update the kernel-doc of tb_dp_port_set_hops() to reflect
this too.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
(cherry picked from commit e5bb88e961e5e3e72e3cc3a866a232115bd15e1e) Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Mika Westerberg [Tue, 8 Mar 2022 08:49:07 +0000 (16:49 +0800)]
thunderbolt: Do not allow subtracting more NFC credits than configured
BugLink: https://bugs.launchpad.net/bugs/1955016
This might happen if the boot firmware uses different amount of NFC
credits than what the router suggests, or we are dealing with pre-USB4
device.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
(cherry picked from commit 6cb27a04fb779717c4a3d20233b93596885838cf) Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
thunderbolt 1-0:3.1: runtime PM trying to activate child device 1-0:3.1 but parent (usb4_port3) is not active
This happens because the parent USB4 port was still runtime suspended.
Fix this by runtime resuming the USB4 port before scanning the retimers
below it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
(cherry picked from commit 1e56c88adecc2dfe14973fa47898861a839e62d4) Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Mika Westerberg [Tue, 8 Mar 2022 08:49:05 +0000 (16:49 +0800)]
thunderbolt: Tear down existing tunnels when resuming from hibernate
BugLink: https://bugs.launchpad.net/bugs/1955016
If the boot firmware implements connection manager of its own it may not
create the paths in the same way or order we do. For example it may
create first PCIe tunnel and then USB3 tunnel. When we restore our
tunnels (first de-activating them) we may be doing that over completely
different tunnels and that leaves them possibly non-functional. For this
reason we re-use the tunnel discovery functionality and find out all the
existing tunnels, and tear them down. Once that is done we can restore
our tunnels.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
(cherry picked from commit 43bddb26e20af916249b5318200cfe1734c1700c) Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Juerg Haefliger [Wed, 9 Mar 2022 09:50:33 +0000 (10:50 +0100)]
UBUNTU: Remove ubuntu/hio driver
The third-party Huawei hio driver provided by the Ubuntu kernel was
added back in Xenial (LP: #1603483). It has been disabled since Impish
because it no longer compiles. Nobody has complained so far, so get rid
of it.
Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
If mt7921e gets started with not ASPM L0, it would be possible that the
driver encounters time to time failure in mt7921_pci_probe, like a
weird chip identifier is read
[ 215.514503] mt7921e 0000:05:00.0: ASIC revision: feed0000
[ 216.604741] mt7921e: probe of 0000:05:00.0 failed with error -110
or failing to init hardware because the driver is not allowed to access the
register until the device is in ASPM L0 state. So, we call
__mt7921e_mcu_drv_pmctrl in early mt7921_pci_probe to force the device
to bring back to the L0 state for we can safely access registers in any
case.
In the patch, we move all functions from dma.c to pci.c and register mt76
bus operation earilier, that is the __mt7921e_mcu_drv_pmctrl depends on.
Fixes: bf3747ae2e25 ("mt76: mt7921: enable aspm by default") Reported-by: Kai-Chuan Hsieh <kaichuan.hsieh@canonical.com> Co-developed-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link:https://lore.kernel.org/r/70e27cbc652cbdb78277b9c691a3a5ba02653afb.1641540175.git.objelf@gmail.com
(backported from
https://patchwork.kernel.org/project/linux-mediatek/patch/70e27cbc652cbdb78277b9c691a3a5ba02653afb.1641540175.git.objelf@gmail.com/) Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Sean Wang [Tue, 8 Mar 2022 03:39:34 +0000 (11:39 +0800)]
mt76: mt7921: enable aspm by default
BugLink: https://bugs.launchpad.net/bugs/1955882
mt7921 is mainly used in NB, CE and IoT application where battery life is
much concerned so the patch enabled PCIe ASPM by default to shut off the
clocks related PCIe as much as possible when MT7921 is either in suspend
state or in runtime pm to lower power consumption.
We still leave disable aspm as an option with module_param for users to
disable ASPM if necessary.
Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit bf3747ae2e25dda6a9e6c464a717c66118c588c8) Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Ricky WU [Fri, 4 Mar 2022 06:55:26 +0000 (14:55 +0800)]
mmc: rtsx: add 74 Clocks in power on flow
BugLink: https://bugs.launchpad.net/bugs/1963615
SD spec definition:
"Host provides at least 74 Clocks before issuing first command"
After 1ms for the voltage stable then start issuing the Clock signals
if POWER STATE is
MMC_POWER_OFF to MMC_POWER_UP to issue Clock signal to card
MMC_POWER_UP to MMC_POWER_ON to stop issuing signal to card
Ulf Hansson [Fri, 4 Mar 2022 06:55:25 +0000 (14:55 +0800)]
mmc: rtsx: Fix build errors/warnings for unused variable
BugLink: https://bugs.launchpad.net/bugs/1963615
The struct device *dev, is no longer needed at various functions, let's
therefore drop it to fix the build errors/warnings.
Fixes: 7570fb41e450 ("mmc: rtsx: Let MMC core handle runtime PM") Cc: Kai-Heng Feng <kai.heng.feng@canonical.com> Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Link: https://lore.kernel.org/r/20220301115300.64332-1-ulf.hansson@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 3dd9a926ec2308e49445f22abef149fc64e9332e linux-next) Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Ricky WU [Fri, 4 Mar 2022 06:55:24 +0000 (14:55 +0800)]
misc: rtsx: rts522a rts5228 rts5261 support Runtime PM
BugLink: https://bugs.launchpad.net/bugs/1963615
rts522a, rts5228, rts5261
add extra init flow for rtd3
add more power_down setting for avoid being woken up
by plugging or unplugging card when system in S3
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Ricky Wu <ricky_wu@realtek.com> Link: https://lore.kernel.org/r/dace32f573a445908fec0a10482c394c@realtek.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 86f4c65fd5003c894dd3082d53e26307fbc211cc linux-next) Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1963615
On s390 allyesconfig, there is this build error
rtsx_pcr.c:1084:13: error: 'rtsx_pm_power_saving'
defined but not used
1084 | static void rtsx_pm_power_saving(struct rtsx_pcr *pcr)
| ^~~~~~~~~~~~~~~~~~~~
rtsx_pm_power_saving() is only used by rtsx_pci_runtime_idle()
which is conditional on CONFIG_PM. So conditionally build
rtsx_pm_power_saving() and the similar
rtsx_comm_pm_power_saving() and rtsx_enable_aspm().
Kai-Heng Feng [Fri, 4 Mar 2022 06:55:22 +0000 (14:55 +0800)]
mmc: rtsx: Let MMC core handle runtime PM
BugLink: https://bugs.launchpad.net/bugs/1963615
Since MMC core handles runtime PM reference counting, we can avoid doing
redundant runtime PM work in the driver. That means the only thing
commit 5b4258f6721f ("misc: rtsx: rts5249 support runtime PM") misses is
to always enable runtime PM, to let its parent driver enable ASPM in the
runtime idle routine.
Fixes: 7499b529d97f ("mmc: rtsx: Use pm_runtime_{get,put}() to handle runtime PM") Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Link: https://lore.kernel.org/r/20220216055435.2335297-1-kai.heng.feng@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 7570fb41e450ba37bf9335fe3751fa9f502c30fa linux-next) Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Kai-Heng Feng [Fri, 4 Mar 2022 06:55:18 +0000 (14:55 +0800)]
mmc: rtsx: Use pm_runtime_{get, put}() to handle runtime PM
BugLink: https://bugs.launchpad.net/bugs/1963615
Commit 5b4258f6721f ("misc: rtsx: rts5249 support runtime PM") doesn't
use pm_runtime_{get,put}() helpers when it should, so the RPM refcount
keeps at zero, hence its parent driver, rtsx_pci, has to do lots of
weird tricks to keep it from runtime suspending.
So use those helpers at right places to properly manage runtime PM.
Fixes: 5b4258f6721f ("misc: rtsx: rts5249 support runtime PM") Cc: Ricky WU <ricky_wu@realtek.com> Tested-by: Ricky WU <ricky_wu@realtek.com> Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Link: https://lore.kernel.org/r/20220125055010.1866563-1-kai.heng.feng@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 7499b529d97f752124fa62fefa1d6d44b371215a linux-next) Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Heiko Carstens [Thu, 24 Feb 2022 19:11:08 +0000 (20:11 +0100)]
s390/crypto: fix compile error for ChaCha20 module
BugLink: https://bugs.launchpad.net/bugs/1853152
The clgfi instruction used within the ChaCha20 assembly is only
available for z9-109 and newer machines, and therefore this will
generate a compile error if compiled e.g. with MARCH_Z900.
Given that the assembler code will only be executed on machines with
vector instructions, which became much later available than z9-109,
use insn notation to generate the clgfi instruction, and avoid compile
errors due to unknown instructions.
Fixes: b087dfab4d39 ("s390/crypto: add SIMD implementation for ChaCha20") Reported-by: kernel test robot <lkp@intel.com> Reviewed-by: Harald Freudenberger <freude@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
(cherry picked from commit 39d02827ed40fd421a758a36264c255d69f5d035) Signed-off-by: Frank Heimes <frank.heimes@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Patrick Steuer [Thu, 24 Feb 2022 19:11:07 +0000 (20:11 +0100)]
s390/crypto: add SIMD implementation for ChaCha20
BugLink: https://bugs.launchpad.net/bugs/1853152
Add an implementation of the ChaCha20 stream cipher (see e.g. RFC 7539)
that makes use of z13's vector instruction set extension.
The original implementation is by Andy Polyakov which is
adapted for kernel use.
Four to six blocks are processed in parallel resulting in a performance
gain for inputs >= 256 bytes.
chacha20-generic
1 operation in 622 cycles (256 bytes)
1 operation in 2346 cycles (1024 bytes)
chacha20-s390
1 operation in 218 cycles (256 bytes)
1 operation in 647 cycles (1024 bytes)
Cc: Andy Polyakov <appro@openssl.org> Reviewed-by: Harald Freudenberger <freude@de.ibm.com> Signed-off-by: Patrick Steuer <patrick.steuer@de.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
(cherry picked from commit b087dfab4d3902681550fd1f5ff9c3e942059478) Signed-off-by: Frank Heimes <frank.heimes@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1959890
The hardware generation that used OSX devices (OSA-Express for zBX)
is obsolete now. Therefore, IBM pulls the support from all Linux distros
going forward.
Hence the deactivation of the CONFIG_QETH_OSX kernel config option
for jammy and onwards.
v2: set policy to "no" instead of removing it and leaving a note
Signed-off-by: Frank Heimes <frank.heimes@canonical.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Stefan Bader [Tue, 22 Feb 2022 16:56:07 +0000 (17:56 +0100)]
UBUNTU: [Packaging] Move VM DRM drivers into modules
BugLink: https://bugs.launchpad.net/bugs/1960633
We already have vboxvideo included in the linux-modules package which is
also included when using the linux-virtual meta. But there is a couple
of other DRM drivers which could be used by various VM installations
which run a desktop:
- bochs-drm (? Qemu)
- cirrus (old standard when it comes to emulated graphics)
- drm_xen_front (Xen)
- virtio-gpu (KVM)
- vmwgfx (VMWare)
All of those drivers direct dependencies are already part of
linux-modules.
Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
HID: amd_sfh: Add interrupt handler to process interrupts
BugLink: https://bugs.launchpad.net/bugs/1961121
On newer AMD platforms with SFH, it is observed that random interrupts
get generated on the SFH hardware and until this is cleared the firmware
sensor processing is stalled, resulting in no data been received to
driver side.
Add routines to handle these interrupts, so that firmware operations are
not stalled.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
(cherry picked from commit 7f016b35ca7623c71b31facdde080e8ce171a697) Signed-off-by: Alex Hung <alex.hung@canonical.com> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
HID: amd_sfh: Add functionality to clear interrupts
BugLink: https://bugs.launchpad.net/bugs/1961121
Newer AMD platforms with SFH may generate interrupts on some events
which are unwarranted. Until this is cleared the actual MP2 data
processing maybe stalled in some cases.
Add a mechanism to clear the pending interrupts (if any) during the
driver initialization and sensor command operations.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
(cherry picked from commit fb75a3791a8032848c987db29b622878d8fe2b1c) Signed-off-by: Alex Hung <alex.hung@canonical.com> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
HID: amd_sfh: Handle amd_sfh work buffer in PM ops
BugLink: https://bugs.launchpad.net/bugs/1961121
Since in the current amd_sfh design the sensor data is periodically
obtained in the form of poll data, during the suspend/resume cycle,
scheduling a delayed work adds no value.
So, cancel the work and restart back during the suspend/resume cycle
respectively.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
(cherry picked from commit 0cf74235f4403b760a37f77271d2ca3424001ff9) Signed-off-by: Alex Hung <alex.hung@canonical.com> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Sven Schnelle [Thu, 17 Feb 2022 19:02:47 +0000 (20:02 +0100)]
s390: support command lines longer than 896 bytes
BugLink: https://bugs.launchpad.net/bugs/1960580
Currently s390 supports a fixed maximum command line length of 896
bytes. This isn't enough as some installers are trying to pass all
configuration data via kernel command line, and even with zfcp alone
it is easy to generate really long command lines. Therefore extend
the command line to 4 kbytes.
In the parm area where the command line is stored there is no indication
of the maximum allowed length, so a new field which contains the maximum
length is added.
The parm area has always been initialized to zero, so with old kernels
this field would read zero. This is important because tools like zipl
could read this field. If it contains a number larger than zero zipl
knows the maximum length that can be stored in the parm area, otherwise
it must assume that it is booting a legacy kernel and only 896 bytes are
available.
The removing of trailing whitespace in head.S is also removed because
code to do this is already present in setup_boot_command_line().
Signed-off-by: Sven Schnelle <svens@linux.ibm.com> Reviewed-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
(cherry picked from commit 5ecb2da660ab8eddafe059a6a8a708465db89ca2) Signed-off-by: Frank Heimes <frank.heimes@canonical.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Sven Schnelle [Thu, 17 Feb 2022 19:02:46 +0000 (20:02 +0100)]
s390/kexec_file: move kernel image size check
BugLink: https://bugs.launchpad.net/bugs/1960580
In preparation of adding support for command lines with variable
sizes on s390, the check whether the new kernel image is at least HEAD_END
bytes long isn't correct. Move the check to kexec_file_add_components()
so we can get the size of the parm area and check the size there.
The '.org HEAD_END' directive can now also be removed from head.S. This
was used in the past to reserve space for the early sccb buffer, but with
commit 9a5131b87cac1 ("s390/boot: move sclp early buffer from fixed address
in asm to C") this is no longer required.
Signed-off-by: Sven Schnelle <svens@linux.ibm.com> Reviewed-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
(backported from commit 277c8389386e2ccb8417afe4e36f67fc5dcd735d) Signed-off-by: Frank Heimes <frank.heimes@canonical.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Thomas Richter [Wed, 16 Feb 2022 11:43:38 +0000 (12:43 +0100)]
s390/cpumf: Support for CPU Measurement Sampling Facility LS bit
BugLink: https://bugs.launchpad.net/bugs/1960182
Adds support for the CPU Measurement Sampling Facility limit sampling
bit in the sampling device driver.
Limited samples have no valueable information are not collected.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com> Acked-by: Sumanth Korikkar <sumanthk@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
(cherry picked from commit 745f5d20e7936931f924410f32d8b0e599b5990e) Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com> Acked-by: Sumanth Korikkar <sumanthk@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
(cherry picked from commit a87b0fd4f9003f8521226e226cf92b18147b3519) Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Adrian Huang [Wed, 16 Feb 2022 05:01:40 +0000 (00:01 -0500)]
PCI: vmd: Do not disable MSI-X remapping if interrupt remapping is enabled by IOMMU
BugLink: https://bugs.launchpad.net/bugs/1937295
When enabling VMD in BIOS setup (Ice Lake Processor: Whitley platform),
the host OS cannot boot successfully with the following error message:
nvme nvme0: I/O 12 QID 0 timeout, completion polled
nvme nvme0: Shutdown timeout set to 6 seconds
DMAR: DRHD: handling fault status reg 2
DMAR: [INTR-REMAP] Request device [0x00:0x00.5] fault index 0xa00 [fault reason 0x25] Blocked a compatibility format interrupt request
The request device is the VMD controller:
# lspci -s 0000:00.5 -nn
0000:00:00.5 RAID bus controller [0104]: Intel Corporation Volume
Management Device NVMe RAID Controller [8086:28c0] (rev 04)
`git bisect` points to this offending commit ee81ee84f873 ("PCI:
vmd: Disable MSI-X remapping when possible"), which disables VMD MSI
remapping. The IOMMU hardware blocks the compatibility format
interrupt request because Interrupt Remapping Enable Status (IRES) and
Extended Interrupt Mode Enable (EIME) are enabled. Please refer to
section "5.1.4 Interrupt-Remapping Hardware Operation" in Intel VT-d
spec.
To fix the issue, VMD driver still enables the interrupt remapping
irrespective of VMD_FEAT_CAN_BYPASS_MSI_REMAP if the IOMMU subsystem
enables the interrupt remapping.
Test configuration is shown as follows:
* Two VMD controllers
1. 8086:28c0 (Whitley's VMD)
2. 8086:201d (Purley's VMD: The issue does not appear in this
controller. Just make sure if any side effect occurs.)
* w/wo intremap=off
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=214219 Link: https://lore.kernel.org/r/20210901124047.1615-1-adrianhuang0701@gmail.com Signed-off-by: Adrian Huang <ahuang12@lenovo.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Jon Derrick <jonathan.derrick@intel.com> Cc: Jon Derrick <jonathan.derrick@intel.com> Cc: Nirmal Patel <nirmal.patel@linux.intel.com> Cc: Joerg Roedel <jroedel@suse.de>
(cherry picked from commit 2565e5b69c44b4e42469afea3cc5a97e74d1ed45) Signed-off-by: Jeff Lane <jeffrey.lane@canonical.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Commit c503e63200c6 ("ice: Stop processing VF messages during teardown")
introduced a driver state flag, ICE_VF_DEINIT_IN_PROGRESS, which is
intended to prevent some issues with concurrently handling messages from
VFs while tearing down the VFs.
This change was motivated by crashes caused while tearing down and
bringing up VFs in rapid succession.
It turns out that the fix actually introduces issues with the VF driver
caused because the PF no longer responds to any messages sent by the VF
during its .remove routine. This results in the VF potentially removing
its DMA memory before the PF has shut down the device queues.
Additionally, the fix doesn't actually resolve concurrency issues within
the ice driver. It is possible for a VF to initiate a reset just prior
to the ice driver removing VFs. This can result in the remove task
concurrently operating while the VF is being reset. This results in
similar memory corruption and panics purportedly fixed by that commit.
Fix this concurrency at its root by protecting both the reset and
removal flows using the existing VF cfg_lock. This ensures that we
cannot remove the VF while any outstanding critical tasks such as a
virtchnl message or a reset are occurring.
This locking change also fixes the root cause originally fixed by commit c503e63200c6 ("ice: Stop processing VF messages during teardown"), so we
can simply revert it.
Note that I kept these two changes together because simply reverting the
original commit alone would leave the driver vulnerable to worse race
conditions.
Fixes: c503e63200c6 ("ice: Stop processing VF messages during teardown") Cc: <stable@vger.kernel.org> # e6ba5273d4ed: ice: Fix race conditions between virtchnl handling and VF ndo ops Cc: <stable@vger.kernel.org> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The VF can be configured via the PF's ndo ops at the same time the PF is
receiving/handling virtchnl messages. This has many issues, with
one of them being the ndo op could be actively resetting a VF (i.e.
resetting it to the default state and deleting/re-adding the VF's VSI)
while a virtchnl message is being handled. The following error was seen
because a VF ndo op was used to change a VF's trust setting while the
VIRTCHNL_OP_CONFIG_VSI_QUEUES was ongoing:
[35274.192484] ice 0000:88:00.0: Failed to set LAN Tx queue context, error: ICE_ERR_PARAM
[35274.193074] ice 0000:88:00.0: VF 0 failed opcode 6, retval: -5
[35274.193640] iavf 0000:88:01.0: PF returned error -5 (IAVF_ERR_PARAM) to our request 6
Fix this by making sure the virtchnl handling and VF ndo ops that
trigger VF resets cannot run concurrently. This is done by adding a
struct mutex cfg_lock to each VF structure. For VF ndo ops, the mutex
will be locked around the critical operations and VFR. Since the ndo ops
will trigger a VFR, the virtchnl thread will use mutex_trylock(). This
is done because if any other thread (i.e. VF ndo op) has the mutex, then
that means the current VF message being handled is no longer valid, so
just ignore it.
This issue can be seen using the following commands:
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
done
Fixes: 7c710869d64e ("ice: Add handlers for VF netdevice operations") Cc: <stable@vger.kernel.org> Signed-off-by: Brett Creeley <brett.creeley@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
[I had to fix the cherry-pick manually as the patch added a line around
some context that was missing.] Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
memblock.{reserved,memory}.regions may be allocated using kmalloc() in
memblock_double_array(). Use kfree() to release these kmalloced regions
indicated by memblock_{reserved,memory}_in_slab.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Fixes: 3010f876500f ("mm: discard memblock data later") Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The tegra186 GPIO driver makes the assumption that the pointer
returned by irq_data_get_irq_chip_data() is a pointer to a
tegra_gpio structure. Unfortunately, it is actually a pointer
to the inner gpio_chip structure, as mandated by the gpiolib
infrastructure. Nice try.
The saving grace is that the gpio_chip is the first member of
tegra_gpio, so the bug has gone undetected since... forever.
Fix it by performing a container_of() on the pointer. This results
in no additional code, and makes it possible to understand how
the whole thing works.
In the current implementation the user may open a virtual tty which then
could fail to establish the underlying DLCI. The function gsmtty_open()
gets stuck in tty_port_block_til_ready() while waiting for a carrier rise.
This happens if the remote side fails to acknowledge the link establishment
request in time or completely. At some point gsm_dlci_close() is called
to abort the link establishment attempt. The function tries to inform the
associated virtual tty by performing a hangup. But the blocking loop within
tty_port_block_til_ready() is not informed about this event.
The patch proposed here fixes this by resetting the initialization state of
the virtual tty to ensure the loop exits and triggering it to make
tty_port_block_til_ready() return.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline") Cc: stable@vger.kernel.org Signed-off-by: Daniel Starke <daniel.starke@siemens.com> Link: https://lore.kernel.org/r/20220218073123.2121-7-daniel.starke@siemens.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The function gsm_process_modem() exists to handle modem status bits of
incoming frames. This includes incoming MSC (modem status command) frames
and convergence layer type 2 data frames. The function, however, was only
designed to handle MSC frames as it expects the command length. Within
gsm_dlci_data() it is wrongly assumed that this is the same as the data
frame length. This is only true if the data frame contains only 1 byte of
payload.
This patch names the length parameter of gsm_process_modem() in a generic
manner to reflect its association. It also corrects all calls to the
function to handle the variable number of modem status octets correctly in
both cases.
Fixes: 7263287af93d ("tty: n_gsm: Fixed logic to decode break signal from modem status") Cc: stable@vger.kernel.org Signed-off-by: Daniel Starke <daniel.starke@siemens.com> Link: https://lore.kernel.org/r/20220218073123.2121-6-daniel.starke@siemens.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
tty flow control is handled via gsmtty_throttle() and gsmtty_unthrottle().
Both functions propagate the outgoing hardware flow control state to the
remote side via MSC (modem status command) frames. The local state is taken
from the RTS (ready to send) flag of the tty. However, RTS gets mapped to
DTR (data terminal ready), which is wrong.
This patch corrects this by mapping RTS to RTS.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline") Cc: stable@vger.kernel.org Signed-off-by: Daniel Starke <daniel.starke@siemens.com> Link: https://lore.kernel.org/r/20220218073123.2121-5-daniel.starke@siemens.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The here fixed commit made the tty hangup asynchronous to avoid a circular
locking warning. I could not reproduce this warning. Furthermore, due to
the asynchronous hangup the function call now gets queued up while the
underlying tty is being freed. Depending on the timing this results in a
NULL pointer access in the global work queue scheduler. To be precise in
process_one_work(). Therefore, the previous commit made the issue worse
which it tried to fix.
This patch fixes this by falling back to the old behavior which uses a
blocking tty hangup call before freeing up the associated tty.
Fixes: 7030082a7415 ("tty: n_gsm: avoid recursive locking with async port hangup") Cc: stable@vger.kernel.org Signed-off-by: Daniel Starke <daniel.starke@siemens.com> Link: https://lore.kernel.org/r/20220218073123.2121-4-daniel.starke@siemens.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Trying to open a DLCI by sending a SABM frame may fail with a timeout.
The link is closed on the initiator side without informing the responder
about this event. The responder assumes the link is open after sending a
UA frame to answer the SABM frame. The link gets stuck in a half open
state.
This patch fixes this by initiating the proper link termination procedure
after link setup timeout instead of silently closing it down.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline") Cc: stable@vger.kernel.org Signed-off-by: Daniel Starke <daniel.starke@siemens.com> Link: https://lore.kernel.org/r/20220218073123.2121-3-daniel.starke@siemens.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.3.7 describes the encoding of the
control signal octet used by the MSC (modem status command). The same
encoding is also used in convergence layer type 2 as described in chapter
5.5.2. Table 7 and 24 both require the DV (data valid) bit to be set 1 for
outgoing control signal octets sent by the DTE (data terminal equipment),
i.e. for the initiator side.
Currently, the DV bit is only set if CD (carrier detect) is on, regardless
of the side.
This patch fixes this behavior by setting the DV bit on the initiator side
unconditionally.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline") Cc: stable@vger.kernel.org Signed-off-by: Daniel Starke <daniel.starke@siemens.com> Link: https://lore.kernel.org/r/20220218073123.2121-1-daniel.starke@siemens.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The trace_hardirqs_{on,off}() require the caller to setup frame pointer
properly. This because these two functions use macro 'CALLER_ADDR1' (aka.
__builtin_return_address(1)) to acquire caller info. If the $fp is used
for other purpose, the code generated this macro (as below) could trigger
memory access fault.
The patch below has two "linkcontrol" names causing the duplication.
Fix by using the correct "diag_counters" name on the second instance.
Fixes: 4a7aaf88c89f ("RDMA/qib: Use attributes for the port sysfs") Link: https://lore.kernel.org/r/1645106372-23004-1-git-send-email-mike.marciniszyn@cornelisnetworks.com Cc: <stable@vger.kernel.org> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The interrupt mask is enabled before any potential failure points in
the driver, which can leave a failure path where we exit with
interrupts enabled but the device not live. This causes an infinite
stream of interrupts on an Apple M1 Pro laptop on USB-C.
Add a failure label that's used post enabling interrupts, where we
mask them again before returning an error.
Suggested-by: Sven Peter <sven@svenpeter.dev> Cc: stable <stable@vger.kernel.org> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Link: https://lore.kernel.org/r/e6b80669-20f3-06e7-9ed5-8951a9c6db6f@kernel.dk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
In rare cases the display is flipped or mirrored. This was observed more
often in a low temperature environment. A clean reset on init_display()
should help to get registers in a sane state.
Fixes: ef8f317795da (staging: fbtft: use init function instead of init sequence) Cc: stable@vger.kernel.org Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com> Link: https://lore.kernel.org/r/20220210085322.15676-1-oliver.graute@kococonnector.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
If the state is not idle then resolve_prepare_src() should immediately
fail and no change to global state should happen. However, it
unconditionally overwrites the src_addr trying to build a temporary any
address.
For instance if the state is already RDMA_CM_LISTEN then this will corrupt
the src_addr and would cause the test in cma_cancel_operation():
if (cma_any_addr(cma_src_addr(id_priv)) && !id_priv->cma_dev)
Which would manifest as this trace from syzkaller:
BUG: KASAN: use-after-free in __list_add_valid+0x93/0xa0 lib/list_debug.c:26
Read of size 8 at addr ffff8881546491e0 by task syz-executor.1/32204
This is indicating that an rdma_id_private was destroyed without doing
cma_cancel_listens().
Instead of trying to re-use the src_addr memory to indirectly create an
any address derived from the dst build one explicitly on the stack and
bind to that as any other normal flow would do. rdma_bind_addr() will copy
it over the src_addr once it knows the state is valid.
This is similar to commit bc0bdc5afaa7 ("RDMA/cma: Do not change
route.addr.src_addr.ss_family")
Link: https://lore.kernel.org/r/0-v2-e975c8fd9ef2+11e-syz_cma_srcaddr_jgg@nvidia.com Cc: stable@vger.kernel.org Fixes: 732d41c545bb ("RDMA/cma: Make the locking for automatic state transition more clear") Reported-by: syzbot+c94a3675a626f6333d74@syzkaller.appspotmail.com Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Compressed length can be corrupted to be a lot larger than memory
we have allocated for buffer.
This will cause memcpy in copy_compressed_segment to write outside
of allocated memory.
This mostly results in stuck read syscall but sometimes when using
btrfs send can get #GP
When unbinding/binding a driver with DMA mapped memory, the DMA map is
not freed before the driver is reloaded. This leads to a memory leak
when the DMA map is overwritten when reprobing the driver.
This can be reproduced with a platform driver having a dma-range:
Wp-gpios property can be used on NVMEM nodes and the same property can
be also used on MTD NAND nodes. In case of the wp-gpios property is
defined at NAND level node, the GPIO management is done at NAND driver
level. Write protect is disabled when the driver is probed or resumed
and is enabled when the driver is released or suspended.
When no partitions are defined in the NAND DT node, then the NAND DT node
will be passed to NVMEM framework. If wp-gpios property is defined in
this node, the GPIO resource is taken twice and the NAND controller
driver fails to probe.
A new Boolean flag named ignore_wp has been added in nvmem_config.
In case ignore_wp is set, it means that the GPIO is handled by the
provider. Lets set this flag in MTD layer to avoid the conflict on
wp_gpios property.
Fixes: 2a127da461a9 ("nvmem: add support for the write-protect pin") Cc: stable@vger.kernel.org Acked-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20220220151432.16605-3-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Wp-gpios property can be used on NVMEM nodes and the same property can
be also used on MTD NAND nodes. In case of the wp-gpios property is
defined at NAND level node, the GPIO management is done at NAND driver
level. Write protect is disabled when the driver is probed or resumed
and is enabled when the driver is released or suspended.
When no partitions are defined in the NAND DT node, then the NAND DT node
will be passed to NVMEM framework. If wp-gpios property is defined in
this node, the GPIO resource is taken twice and the NAND controller
driver fails to probe.
It would be possible to set config->wp_gpio at MTD level before calling
nvmem_register function but NVMEM framework will toggle this GPIO on
each write when this GPIO should only be controlled at NAND level driver
to ensure that the Write Protect has not been enabled.
A way to fix this conflict is to add a new boolean flag in nvmem_config
named ignore_wp. In case ignore_wp is set, the GPIO resource will
be managed by the provider.
Fixes: 2a127da461a9 ("nvmem: add support for the write-protect pin") Cc: stable@vger.kernel.org Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20220220151432.16605-2-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>