The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
With CONFIG_FORTIFY_SOURCE, memcpy uses the declared size of operands to
detect buffer overflows. If src or dest is declared as a char, attempts to
copy more than byte will result in a fortify_panic().
Address this problem in mvebu_setup_boot_addr_wa() by declaring
mvebu_boot_wa_start and mvebu_boot_wa_end as character arrays. Also remove
a couple addressof operators to avoid "arithmetic on pointer to an
incomplete type" compiler error.
See commit 54a7d50b9205 ("x86: mark kprobe templates as character arrays,
not single characters") for a similar fix.
Fixes "detected buffer overflow in memcpy" error during init on some mvebu
systems (armada-370-xp, armada-375):
(fortify_panic) from (mvebu_setup_boot_addr_wa+0xb0/0xb4)
(mvebu_setup_boot_addr_wa) from (mvebu_v7_cpu_pm_init+0x154/0x204)
(mvebu_v7_cpu_pm_init) from (do_one_initcall+0x7c/0x1a8)
(do_one_initcall) from (kernel_init_freeable+0x1bc/0x254)
(kernel_init_freeable) from (kernel_init+0x8/0x114)
(kernel_init) from (ret_from_fork+0x14/0x2c)
The last value in the log_table wraps around to a negative value
since s16 has a value range of -32768 to 32767. This is not what
the table intends to represent. Use the closest positive value
32767.
This fixes a warning seen with clang:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_qmath.c:216:2: warning:
implicit conversion from 'int' to 's16' (aka 'short') changes
value from 32768
to -32768 [-Wconstant-conversion]
32768
^~~~~
1 warning generated.
Fixes: 4c0bfeaae9f9 ("brcmsmac: fix array out-of-bounds access in qm_log10") Cc: Tobias Regnery <tobias.regnery@gmail.com> Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This is a static checker fix, not something I have tested. The issue
is that on the second iteration through the loop, we jump forward by
le32_to_cpu(auth_req->length) bytes. The problem is that if the length
is more than "buflen" then we end up with a negative "buflen". A
negative buflen is type promoted to a high positive value and the loop
continues but it's accessing beyond the end of the buffer.
I believe the "auth_req->length" comes from the firmware and if the
firmware is malicious or buggy, you're already toasted so the impact of
this bug is probably not very severe.
Fixes: 030645aceb3d ("rndis_wlan: handle 802.11 indications from device") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There are frames in the ieee80211_txq and there are frames that have
been removed from from this queue, but haven't yet been sent on the wire
(num_pending_tx).
When num_pending_tx reaches max_num_pending_tx, we will stop the queues
by calling ieee80211_stop_queues().
As frames that have previously been sent for transmission
(num_pending_tx) are completed, we will decrease num_pending_tx and wake
the queues by calling ieee80211_wake_queue(). ieee80211_wake_queue()
does not call wake_tx_queue, so we might still have frames in the
queue at this point.
While the queues were stopped, the socket buffer might have filled up,
and in order for user space to write more, we need to free the frames
in the queue, since they are accounted to the socket. In order to free
them, we first need to transmit them.
This problem cannot be reproduced on low-latency devices, e.g. pci,
since they call ath10k_mac_tx_push_pending() from
ath10k_htt_txrx_compl_task(). ath10k_htt_txrx_compl_task() is not called
on high-latency devices.
Fix the problem by calling ath10k_mac_tx_push_pending(), after
processing rx packets, just like for low-latency devices, also in the
SDIO case. Since we are calling ath10k_mac_tx_push_pending() directly,
we also need to export it.
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since a phy_device is added to the global mdio_bus list during
phy_device_register(), but a phy_device's phy_driver doesn't get
attached until phy_probe(). It's possible of_phy_find_device() in
xgmiitorgmii will return a valid phy with a NULL phy_driver. Leading to
a NULL pointer access during the memcpy().
Fixes this Oops:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.14.40 #1
Hardware name: Xilinx Zynq Platform
task: ce4c8d00 task.stack: ce4ca000
PC is at memcpy+0x48/0x330
LR is at xgmiitorgmii_probe+0x90/0xe8
pc : [<c074bc68>] lr : [<c0529548>] psr: 20000013
sp : ce4cbb54 ip : 00000000 fp : ce4cbb8c
r10: 00000000 r9 : 00000000 r8 : c0c49178
r7 : 00000000 r6 : cdc14718 r5 : ce762800 r4 : cdc14710
r3 : 00000000 r2 : 00000054 r1 : 00000000 r0 : cdc14718
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 18c5387d Table: 0000404a DAC: 00000051
Process swapper/0 (pid: 1, stack limit = 0xce4ca210)
...
[<c074bc68>] (memcpy) from [<c0529548>] (xgmiitorgmii_probe+0x90/0xe8)
[<c0529548>] (xgmiitorgmii_probe) from [<c0526a94>] (mdio_probe+0x28/0x34)
[<c0526a94>] (mdio_probe) from [<c04db98c>] (driver_probe_device+0x254/0x414)
[<c04db98c>] (driver_probe_device) from [<c04dbd58>] (__device_attach_driver+0xac/0x10c)
[<c04dbd58>] (__device_attach_driver) from [<c04d96f4>] (bus_for_each_drv+0x84/0xc8)
[<c04d96f4>] (bus_for_each_drv) from [<c04db5bc>] (__device_attach+0xd0/0x134)
[<c04db5bc>] (__device_attach) from [<c04dbdd4>] (device_initial_probe+0x1c/0x20)
[<c04dbdd4>] (device_initial_probe) from [<c04da8fc>] (bus_probe_device+0x98/0xa0)
[<c04da8fc>] (bus_probe_device) from [<c04d8660>] (device_add+0x43c/0x5d0)
[<c04d8660>] (device_add) from [<c0526cb8>] (mdio_device_register+0x34/0x80)
[<c0526cb8>] (mdio_device_register) from [<c0580b48>] (of_mdiobus_register+0x170/0x30c)
[<c0580b48>] (of_mdiobus_register) from [<c05349c4>] (macb_probe+0x710/0xc00)
[<c05349c4>] (macb_probe) from [<c04dd700>] (platform_drv_probe+0x44/0x80)
[<c04dd700>] (platform_drv_probe) from [<c04db98c>] (driver_probe_device+0x254/0x414)
[<c04db98c>] (driver_probe_device) from [<c04dbc58>] (__driver_attach+0x10c/0x118)
[<c04dbc58>] (__driver_attach) from [<c04d9600>] (bus_for_each_dev+0x8c/0xd0)
[<c04d9600>] (bus_for_each_dev) from [<c04db1fc>] (driver_attach+0x2c/0x30)
[<c04db1fc>] (driver_attach) from [<c04daa98>] (bus_add_driver+0x50/0x260)
[<c04daa98>] (bus_add_driver) from [<c04dc440>] (driver_register+0x88/0x108)
[<c04dc440>] (driver_register) from [<c04dd6b4>] (__platform_driver_register+0x50/0x58)
[<c04dd6b4>] (__platform_driver_register) from [<c0b31248>] (macb_driver_init+0x24/0x28)
[<c0b31248>] (macb_driver_init) from [<c010203c>] (do_one_initcall+0x60/0x1a4)
[<c010203c>] (do_one_initcall) from [<c0b00f78>] (kernel_init_freeable+0x15c/0x1f8)
[<c0b00f78>] (kernel_init_freeable) from [<c0763d10>] (kernel_init+0x18/0x124)
[<c0763d10>] (kernel_init) from [<c0112d74>] (ret_from_fork+0x14/0x20)
Code: ba000002f5d1f03cf5d1f05cf5d1f07c (e8b151f8)
---[ end trace 3e4ec21905820a1f ]---
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
While debugging driver crashes related to a buggy firmware
crashing under load, I noticed that ath10k_htt_rx_ring_free
could be called without being under lock. I'm not sure if this
is the root cause of the crash or not, but it seems prudent to
protect it.
Originally tested on 4.16+ kernel with ath10k-ct 10.4 firmware
running on 9984 NIC.
Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The ashmem driver did not check that the size/offset of the vma passed
to its .mmap() function was not larger than the ashmem object being
mapped. This could cause mmap() to succeed, even though accessing parts
of the mapping would later fail with a segmentation fault.
Ensure an error is returned by the ashmem_mmap() function if the vma
size is larger than the ashmem object size. This enables safer handling
of the problem in userspace.
The struct clk_init_data init variable is declared in the isp_xclk_init()
function so is an automatic variable allocated in the stack. But it's not
explicitly zero-initialized, so some init fields are left uninitialized.
This causes the data structure to have undefined values that may confuse
the common clock framework when the clock is registered.
For example, the uninitialized .flags field could have the CLK_IS_CRITICAL
bit set, causing the framework to wrongly prepare the clk on registration.
This leads to the isp_xclk_prepare() callback being called, which in turn
calls to the omap3isp_get() function that increments the isp dev refcount.
Since this omap3isp_get() call is unexpected, this leads to an unbalanced
omap3isp_get() call that prevents the requested IRQ to be later enabled,
due the refcount not being 0 when the correct omap3isp_get() call happens.
Fixes: 9b28ee3c9122 ("[media] omap3isp: Use the common clock framework") Signed-off-by: Javier Martinez Canillas <javierm@redhat.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The banding filter ON/OFF is controlled via bit 5 of COM8 register. It
is attempted to be enabled in ov772x_set_params() by the following line.
ret = ov772x_mask_set(client, COM8, BNDF_ON_OFF, 1);
But this unexpectedly results disabling the banding filter, because the
mask and set bits are exclusive.
On the other hand, ov772x_s_ctrl() correctly sets the bit by:
ret = ov772x_mask_set(client, COM8, BNDF_ON_OFF, BNDF_ON_OFF);
The same fix was already applied to non-soc_camera version of ov772x
driver in the commit commit a024ee14cd36 ("media: ov772x: correct setting
of banding filter")
When the subdevice doesn't provide s_power core ops callback, the
v4l2_subdev_call for s_power returns -ENOIOCTLCMD. If the subdevice
doesn't have the special handling for its power saving mode, the s_power
isn't required. So -ENOIOCTLCMD from the v4l2_subdev_call should be
ignored.
Cc: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Acked-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Both calls to of_find_node_by_name() and of_get_next_child() return a
node pointer with refcount incremented thus it must be explicidly
decremented here after the last usage. As we are assured to have a
refcounted np either from the initial
of_find_node_by_name(NULL, name); or from the of_get_next_child(gpio, np)
in the while loop if we reached the error code path below, an
x of_node_put(np) is needed.
The posix timer ti_overrun handling is broken because the forwarding
functions can return a huge number of overruns which does not fit in an
int. As a consequence timer_getoverrun(2) and siginfo::si_overrun can turn
into random number generators.
As a first step to address that let the timer_forward() callbacks return
the full 64 bit value.
Cast it to (int) temporarily until k_itimer::ti_overrun is converted to
64bit and the conversion to user space visible values is sanitized.
Reported-by: Team OWL337 <icytxw@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: John Stultz <john.stultz@linaro.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Michael Kerrisk <mtk.manpages@gmail.com> Link: https://lkml.kernel.org/r/20180626132704.922098090@linutronix.de Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently the address field in iio_chan_spec is filled with an accel
data register address for the corresponding axis.
In preparation for adding calibration offset support, this sets the
address field to the index of accel data registers instead of the actual
register address.
This change makes it easier to access both accel registers and
calibration offset registers with fewer lines of code as these are
located in X-axis, Y-axis, Z-axis order.
Cc: Eva Rachel Retuya <eraretuya@gmail.com> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On a sama5d31 with a Full-HD dual LVDS panel (132MHz pixel clock) NAND
flash accesses have a tendency to cause display disturbances. Add a
module param to disable DMA from the NAND controller, since that fixes
the display problem for me.
Signed-off-by: Peter Rosin <peda@axentia.se> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
arch/s390/mm/extmem.c: In function '__segment_load':
arch/s390/mm/extmem.c:436:2: warning: 'strncat' specified bound 7 equals
source length [-Wstringop-overflow=]
strncat(seg->res_name, " (DCSS)", 7);
What gcc complains about here is the misuse of strncat function, which
in this case does not limit a number of bytes taken from "src", so it is
in the end the same as strcat(seg->res_name, " (DCSS)");
Keeping in mind that a res_name is 15 bytes, strncat in this case
would overflow the buffer and write 0 into alignment byte between the
fields in the struct. To avoid that increasing res_name size to 16,
and reusing strlcat.
The numa_node field of the tag_set struct has to be explicitly
initialized, otherwise it stays as 0, which is a valid numa node id and
cause memory allocation failure if node 0 is offline.
Acked-by: Sebastian Ott <sebott@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The numa_node field of the tag_set struct has to be explicitly
initialized, otherwise it stays as 0, which is a valid numa node id and
cause memory allocation failure if node 0 is offline.
Acked-by: Stefan Haberland <sth@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
UBSAN: Undefined behaviour in kernel/time/alarmtimer.c:811:7
signed integer overflow: 1529859276030040771 + 9223372036854775807 cannot be represented in type 'long long int'
Call Trace:
alarm_timer_nsleep+0x44c/0x510 kernel/time/alarmtimer.c:811
__do_sys_clock_nanosleep kernel/time/posix-timers.c:1235 [inline]
__se_sys_clock_nanosleep kernel/time/posix-timers.c:1213 [inline]
__x64_sys_clock_nanosleep+0x326/0x4e0 kernel/time/posix-timers.c:1213
do_syscall_64+0xb8/0x3a0 arch/x86/entry/common.c:290
alarm_timer_nsleep() uses ktime_add() to add the current time and the
relative expiry value. ktime_add() has no sanity checks so the addition
can overflow when the relative timeout is large enough.
Use ktime_add_safe() which has the necessary sanity checks in place and
limits the result to the valid range.
Fixes: 9a7adcf5c6de ("timers: Posix interface for alarm-timers") Reported-by: Team OWL337 <icytxw@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: John Stultz <john.stultz@linaro.org> Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1807020926360.1595@nanos.tec.linutronix.de Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
CC arch/s390/kernel/sysinfo.o
arch/s390/kernel/sysinfo.c:275:12: warning: 'sysinfo_show' defined but not used [-Wunused-function]
static int sysinfo_show(struct seq_file *m, void *v)
We use PHB in mode1 which uses bit 59 to select a correct DMA window.
However there is mode2 which uses bits 59:55 and allows up to 32 DMA
windows per a PE.
Even though documentation does not clearly specify that, it seems that
the actual hardware does not support bits 59:55 even in mode1, in other
words we can create a window as big as 1<<58 but DMA simply won't work.
This reduces the upper limit from 59 to 55 bits to let the userspace know
about the hardware limits.
Fixes: 7aafac11e3 "powerpc/powernv/ioda2: Gracefully fail if too many TCE levels requested" Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
All packets in a bundle should use the same endpoint id as the
first lookahead.
This matches how things are done is ath6kl, however,
this patch can theoretically handle several bundles
in ath10k_sdio_mbox_rx_process_packets().
Without this patch we get lots of errors about invalid endpoint id:
ath10k_sdio mmc2:0001:1: invalid endpoint in look-ahead: 224
ath10k_sdio mmc2:0001:1: failed to get pending recv messages: -12
ath10k_sdio mmc2:0001:1: failed to process pending SDIO interrupts: -12
Comparing an int to a size, which is unsigned, causes the int to become
unsigned, giving the wrong result. usb_get_descriptor can return a
negative error code.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
int x;
expression e,e1;
identifier f;
@@
*x = f(...);
... when != x = e1
when != if (x < 0 || ...) { ... return ...; }
*x < sizeof(e)
// </smpl>
The approach for adding a device to the devices_idr data structure and for
removing it is as follows:
* &dev->dev_group.cg_item is initialized before a device is added to
devices_idr.
* If the reference count of a device drops to zero then
target_free_device() removes the device from devices_idr.
* All devices_idr manipulations are protected by device_mutex.
This means that increasing the reference count of a device is sufficient to
prevent removal from devices_idr and also that it is safe access
dev_group.cg_item for any device that is referenced by devices_idr. Use
this to modify target_find_device() and target_for_each_device() such that
these functions no longer introduce a dependency between device_mutex and
the configfs root inode mutex.
Note: it is safe to pass a NULL pointer to config_item_put() and also to
config_item_get_unless_zero().
This patch prevents that lockdep reports the following complaint:
======================================================
WARNING: possible circular locking dependency detected
4.12.0-rc1-dbg+ #1 Not tainted
------------------------------------------------------
rmdir/12053 is trying to acquire lock:
(device_mutex#2){+.+.+.}, at: [<ffffffffa010afce>]
target_free_device+0xae/0xf0 [target_core_mod]
but task is already holding lock:
(&sb->s_type->i_mutex_key#14){++++++}, at: [<ffffffff811c5c30>]
vfs_rmdir+0x50/0x140
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Currently an open firmware property is copied into partition_name variable
without keeping a room for \0.
Later one, this variable (partition_name), which is 97 bytes long, is
strncpyed into ibmvcsci_host_data->madapter_info->partition_name, which is
96 bytes long, possibly truncating it 'again' and removing the \0.
This patch simply decreases the partition name to 96 and just copy using
strlcpy() which guarantees that the string is \0 terminated. I think there
is no issue if this there is a truncation in this very first copy, i.e,
when the open firmware property is read and copied into the driver for the
very first time;
This issue also causes the following warning on GCC 8:
drivers/scsi/ibmvscsi/ibmvscsi.c:281:2: warning: strncpy output may be truncated copying 96 bytes from a string of length 96 [-Wstringop-truncation]
...
inlined from ibmvscsi_probe at drivers/scsi/ibmvscsi/ibmvscsi.c:2221:7:
drivers/scsi/ibmvscsi/ibmvscsi.c:265:3: warning: strncpy specified bound 97 equals destination size [-Wstringop-truncation]
CC: Bart Van Assche <bart.vanassche@wdc.com> CC: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: Breno Leitao <leitao@debian.org> Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In the scsi_transport_srp implementation it cannot be avoided to
iterate over a klist from atomic context when using the legacy block
layer instead of blk-mq. Hence this patch that makes it safe to use
klists in atomic context. This patch avoids that lockdep reports the
following:
WARNING: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected
Possible interrupt unsafe locking scenario:
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
... there are two more instances which want to be adjusted.
As said there, omitting suffixes from instructions in AT&T mode is bad
practice when operand size cannot be determined by the assembler from
register operands, and is likely going to be warned about by upstream
gas in the future (mine does already).
Add the other missing suffixes here as well.
Signed-off-by: Jan Beulich <jbeulich@suse.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/5B3A02DD02000078001CFB78@prv1-mh.provo.novell.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When the RTC lock and unlock functions were introduced it was likely
assumed that they would always be called from irq enabled context, hence
the use of local_irq_disable/enable. This is no longer true as the
RTC+DDR path makes a late call during the suspend path after irqs
have been disabled to enable the RTC hwmod which calls both unlock and
lock, leading to IRQs being reenabled through the local_irq_enable call
in omap_hwmod_rtc_lock call.
To avoid this change the local_irq_disable/enable to
local_irq_save/restore to ensure that from whatever context this is
called the proper IRQ configuration is maintained.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Add a missing header otherwise compiler warns about missed prototype:
CC arch/x86/kernel/tsc_msr.o
arch/x86/kernel/tsc_msr.c:73:15: warning: no previous prototype for ‘cpu_khz_from_msr’ [-Wmissing-prototypes]
unsigned long cpu_khz_from_msr(void)
^~~~~~~~~~~~~~~~
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Pavel Tatashin <pasha.tatashin@oracle.com> Link: https://lkml.kernel.org/r/20180629193113.84425-4-andriy.shevchenko@linux.intel.com Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
0:00:00.716640334 349 0x164f720 WARN v4l2bufferpool gstv4l2bufferpool.c:1195:gst_v4l2_buffer_pool_dqbuf:<v4l2src0:pool:src> Driver should never set v4l2_buffer.field to ANY
- fixes v4l2-compliance test failure:
Streaming ioctls:
test read/write: OK (Not Supported)
Video Capture:
Buffer: 0 Sequence: 0 Field: Any Timestamp: 58.383658s
fail: v4l2-test-buffers.cpp(297): g_field() == V4L2_FIELD_ANY
Signed-off-by: Peter Seiderer <ps.report@gmx.net> Reviewed-by: Steve Longerbeam <steve_longerbeam@mentor.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Memory reservation for crashkernel could fail if there are holes around
kdump kernel offset (128M). Fail gracefully in such cases and print an
error message.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com> Tested-by: David Gibson <dgibson@redhat.com> Reviewed-by: Dave Young <dyoung@redhat.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
rdma_ah_find_type() can reach into ib_device->port_immutable with a
potentially out-of-bounds port number, so check that the port number is
valid first.
Fixes: 44c58487d51a ("IB/core: Define 'ib' and 'roce' rdma_ah_attr types") Signed-off-by: Tarick Bedeir <tarick@google.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
"nents" is an unsigned int, so if ib_map_mr_sg() returns a negative
error code then it's type promoted to a high unsigned int which is
treated as success.
The sgid_tbl->tbl[] array is allocated in bnxt_qplib_alloc_sgid_tbl().
It has sgid_tbl->max elements. So the > should be >= to prevent
accessing one element beyond the end of the array.
Fixes: 1ac5a4047975 ("RDMA/bnxt_re: Add bnxt_re RoCE driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Selvin Xavier <selvin.xavier@broadcom.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When one node leaves cluster or stops the resyncing
(resync or recovery) array, then other nodes need to
call recover_bitmaps to continue the unfinished task.
But we need to clear suspend_area later after other
nodes copy the resync information to their bitmap
(by call bitmap_copy_from_slot). Otherwise, all nodes
could write to the suspend_area even the suspend_area
is not handled by any node, because area_resyncing
returns 0 at the beginning of raid1_write_request.
Which means one node could write suspend_area while
another node is resyncing the same area, then data
could be inconsistent.
So let's clear suspend_area later to avoid above issue
with the protection of bm lock. Also it is straightforward
to clear suspend_area after nodes have copied the resync
info to bitmap.
If a device gets removed right after having registered a power_supply node,
we might enter in a deadlock between the remove call (that has a lock on
the parent device) and the deferred register work.
Allow the deferred register work to exit without taking the lock when
we are in the remove state.
Since proc_dointvec does not perform value range control,
proc_dointvec_minmax should be used to limit value range, which is
clearly intended here, as the internal representation of the value:
After decompression of 6lowpan socket data, an IPv6 header is inserted
before the existing socket payload. After this, we reset the
network_header value of the skb to account for the difference in payload
size from prior to decompression + the addition of the IPv6 header.
However, we fail to reset the mac_header value.
Leaving the mac_header value untouched here, can cause a calculation
error in net/packet/af_packet.c packet_rcv() function when an
AF_PACKET socket is opened in SOCK_RAW mode for use on a 6lowpan
interface.
On line 2088, the data pointer is moved backward by the value returned
from skb_mac_header(). If skb->data is adjusted so that it is before
the skb->head pointer (which can happen when an old value of mac_header
is left in place) the kernel generates a panic in net/core/skbuff.c
line 1717.
This panic can be generated by BLE 6lowpan interfaces (such as bt0) and
802.15.4 interfaces (such as lowpan0) as they both use the same 6lowpan
sources for compression and decompression.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com> Acked-by: Alexander Aring <aring@mojatatu.com> Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Although the mapping has already been removed in the page table, it maybe
still exist in TLB. Suppose the freed IOVAs is reused by others before the
flush operation completed, the new user can not correctly access to its
meomory.
Vexpress platforms provide two different restart handlers: SYS_REBOOT
that restart the entire system, while DB_RESET only restarts the
daughter board containing the CPU. DB_RESET is overridden by SYS_REBOOT
if it exists.
notifier_chain_register used in register_restart_handler by design
relies on notifiers to be registered once only, however vexpress restart
notifier can get registered twice. When this happen it corrupts list
of notifiers, as result some notifiers can be not called on proper
event, traverse on list can be cycled forever, and second unregister
can access already freed memory.
So far, since this was the only restart handler in the system, no issue
was observed even if the same notifier was registered twice. However
commit 6c5c0d48b686 ("watchdog: sp805: add restart handler") added
support for SP805 restart handlers and since the system under test
contains two vexpress restart and two SP805 watchdog instances, it was
observed that during the boot traversing the restart handler list looped
forever as there's a cycle in that list resulting in boot hang.
This patch fixes the issues by ensuring that the notifier is installed
only once.
Cc: Sebastian Reichel <sre@kernel.org> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Fixes: 46c99ac66222 ("power/reset: vexpress: Register with kernel restart handler") Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently the check on error return from the call to rtsx_write_register
is checking the error status from the previous call. Fix this by adding
in the missing assignment of retval.
Detected by CoverityScan, CID#709877
Fixes: fa590c222fba ("staging: rts5208: add support for rts5208 and rts5288") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The problem is that if get_user_pages_fast() fails and returns a
negative error code, it gets type promoted to a high positive value and
treated as a success.
ADC channel 0 photodiode detects both infrared + visible light,
but ADC channel 1 just detects infrared. However, the latter is a bit
more sensitive in that range so complete darkness or low light causes
a error condition in which the chan0 - chan1 is negative that
results in a -EAGAIN.
This patch changes the resulting lux1_input sysfs attribute message from
"Resource temporarily unavailable" to a user-grokable lux value of 0.
When the buffer is enabled for ina2xx driver, a dedicated kthread is
invoked to capture mesurement data. When the buffer is disabled, the
kthread is stopped.
However if the kthread gets register access errors, it immediately exits
and when the malfunctional buffer is disabled, the stale task_struct
pointer is accessed as there is no kthread to be stopped.
A similar issue in the usbip driver is prevented by kthread_get_run and
kthread_stop_put helpers by increasing usage count of the task_struct.
This change applies the same solution.
Cc: Stefan Brüns <stefan.bruens@rwth-aachen.de> Cc: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Fixes: c43a102e67db ("iio: ina2xx: add support for TI INA2xx Power Monitors") Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Sync syscall to DAX file needs to flush processor cache, but it
currently does not flush to existing DAX files. This is because
'ext4_da_aops' is set to address_space_operations of existing DAX
files, instead of 'ext4_dax_aops', since S_DAX flag is set after
ext4_set_aops() in the open path.
New file
--------
lookup_open
ext4_create
__ext4_new_inode
ext4_set_inode_flags // Set S_DAX flag
ext4_set_aops // Set aops to ext4_dax_aops
Existing file
-------------
lookup_open
ext4_lookup
ext4_iget
ext4_set_aops // Set aops to ext4_da_aops
ext4_set_inode_flags // Set S_DAX flag
Change ext4_iget() to initialize i_flags before ext4_set_aops().
Since actual hotplug notifications don't get disabled until
nouveau_display_fini() is called, all this will do is cause any hotplugs
that happen between this drm_kms_helper_poll_disable() call and the
actual hotplug disablement to potentially be dropped if ACPI isn't
around to help us.
Signed-off-by: Lyude Paul <lyude@redhat.com> Acked-by: Karol Herbst <kherbst@redhat.com> Acked-by: Daniel Vetter <daniel@ffwll.ch> Cc: stable@vger.kernel.org Cc: Lukas Wunner <lukas@wunner.de> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently, nouveau will re-write the DP_MSTM_CTRL register for an MST
hub every time it receives a long HPD pulse on DP. This isn't actually
necessary and additionally, has some unintended side effects.
With the P50 I've got here, rewriting DP_MSTM_CTRL constantly seems to
make it rather likely (1 out of 5 times usually) that bringing up MST
with it's ThinkPad dock will fail and result in sideband messages timing
out in the middle. Afterwards, successive probes don't manage to get the
dock to communicate properly over MST sideband properly.
Many times sideband message timeouts from MST hubs are indicative of
either the source or the sink dropping an ESI event, which can cause
DRM's perspective of the topology's current state to go out of sync with
reality. While it's tough to really know for sure what's happening to
the dock, using userspace tools to write to DP_MSTM_CTRL in the middle
of the MST link probing process does appear to make things flaky. It's
possible that when we write to DP_MSTM_CTRL, the function that gets
triggered to respond in the dock's firmware temporarily puts it in a
state where it might end up not reporting an ESI to the source, or ends
up dropping a sideband message we sent it.
So, to fix this we make it so that when probing an MST topology, we
respect it's current state. If the dock's already enabled, we simply
read DP_MSTM_CTRL and disable the topology if it's value is not what we
expected. Otherwise, we perform the normal MST probing dance. We avoid
taking any action except if the state of the MST topology actually
changes.
This fixes MST sideband message timeouts and detection failures on my
P50 with its ThinkPad dock.
Signed-off-by: Lyude Paul <lyude@redhat.com> Cc: stable@vger.kernel.org Cc: Karol Herbst <karolherbst@gmail.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When probing a new MST device, it's not safe to make any assumptions
about it's current state. While most well mannered MST hubs will just
disable the branching unit on hotplug disconnects, this isn't enough to
save us from various other scenarios that might have resulted in
something writing to the MST branching unit before we got control of it.
This could happen if a previous probe we tried failed, if we're booting
in kexec context and the hub is still in the state the last kernel put
it in, etc.
Luckily; there is no reason we can't just reset the branching unit
every time we enable a new topology. So, fix this by resetting it on
enabling new topologies to ensure that we always start off with a clean,
unmodified topology state on MST sinks.
This fixes occasional hard-lockups on my P50's laptop dock (e.g. AUX
times out all DPCD trasactions) observed after multiple docks, undocks,
and module reloads.
Signed-off-by: Lyude Paul <lyude@redhat.com> Cc: stable@vger.kernel.org Cc: Karol Herbst <karolherbst@gmail.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
hen we're comparing the hardware completion mask passed in from the
driver with the internal tag pending mask, we need to account for the
fact that the internal tag is different from the hardware tag. If not,
then we can end up either prematurely completing the internal tag (since
it's not set in the hw mask), or simply flag an error:
Deferred struct page init is needed only on systems with large amount of
physical memory to improve boot performance. 32-bit systems do not
benefit from this feature.
Jiri reported a problem where deferred struct pages do not work well with
x86-32:
Make the clone and fork syscalls return EAGAIN when the limit on the
number of pids /proc/sys/kernel/pid_max is exceeded.
Currently, when the pid_max limit is exceeded, the kernel will return
ENOSPC from the fork and clone syscalls. This is contrary to the
documented behaviour, which explicitly calls out the pid_max case as one
where EAGAIN should be returned. It also leads to really confusing error
messages in userspace programs which will complain about a lack of disk
space when they fail to create processes/threads for this reason.
This error is being returned because alloc_pid() uses the idr api to find
a new pid; when there are none available, idr_alloc_cyclic() returns
-ENOSPC, and this is being propagated back to userspace.
This behaviour has been broken before, and was explicitly fixed in
commit 35f71bc0a09a ("fork: report pid reservation failure properly"),
so I think -EAGAIN is definitely the right thing to return in this case.
The current behaviour change dates from commit 95846ecf9dac ("pid:
replace pid bitmap implementation with IDR AIP") and was I believe
unintentional.
This patch has no impact on the case where allocating a pid fails because
the child reaper for the namespace is dead; that case will still return
-ENOMEM.
Link: http://lkml.kernel.org/r/20180903111016.46461-1-ktsanaktsidis@zendesk.com Fixes: 95846ecf9dac ("pid: replace pid bitmap implementation with IDR AIP") Signed-off-by: KJ Tsanaktsidis <ktsanaktsidis@zendesk.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Gargi Sharma <gs051095@gmail.com> Cc: Rik van Riel <riel@redhat.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
I thought the read-back of the DMA_ENABLE register was unnecessary
(at least it is working on my boards), then deleted it in commit 586a2c52909d ("mtd: nand: denali: squash denali_enable_dma() helper
into caller"). Sorry, I was wrong - it caused a timing issue on
Cyclone5 SoCFPGAs.
Revive the register read-back, commenting why this is necessary.
This fix addresses https://bugzilla.kernel.org/show_bug.cgi?id=201071
Commit 5025f7f7d506 wrongly relied on __dev_change_flags to notify users of
dev flag changes in the case when dev->rtnl_link_state = RTNL_LINK_INITIALIZED.
Fix it by indicating flag changes explicitly to __dev_notify_flags.
Fixes: 5025f7f7d506 ("rtnetlink: add rtnl_link_state check in rtnl_configure_link") Reported-By: Liam mcbirnie <liam.mcbirnie@boeing.com> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The recent commit to always forward the VF MAC address to the PF for
approval may not work if the PF driver or the firmware is older. This
will cause the VF driver to fail during probe:
bnxt_en 0000:00:03.0 (unnamed net_device) (uninitialized): hwrm req_type 0xf seq id 0x5 error 0xffff
bnxt_en 0000:00:03.0 (unnamed net_device) (uninitialized): VF MAC address 00:00:17:02:05:d0 not approved by the PF
bnxt_en 0000:00:03.0: Unable to initialize mac address.
bnxt_en: probe of 0000:00:03.0 failed with error -99
We fix it by treating the error as fatal only if the VF MAC address is
locally generated by the VF.
Fixes: 707e7e966026 ("bnxt_en: Always forward VF MAC address to the PF.") Reported-by: Seth Forshee <seth.forshee@canonical.com> Reported-by: Siwei Liu <loseweigh@gmail.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When netvsc device is removed it can call reschedule in RCU context.
This happens because canceling the subchannel setup work could (in theory)
cause a reschedule when manipulating the timer.
To reproduce, run with lockdep enabled kernel and unbind
a network device from hv_netvsc (via sysfs).
Thomas Gleixner [Thu, 30 Aug 2018 15:05:19 +0000 (17:05 +0200)]
tick/nohz: Prevent bogus softirq pending warning
BugLink: https://bugs.launchpad.net/bugs/1836287
Commit 0a0e0829f990 ("nohz: Fix missing tick reprogram when interrupting an
inline softirq") got backported to stable trees and now causes the NOHZ
softirq pending warning to trigger. It's not an upstream issue as the NOHZ
update logic has been changed there.
The problem is when a softirq disabled section gets interrupted and on
return from interrupt the tick/nohz state is evaluated, which then can
observe pending soft interrupts. These soft interrupts are legitimately
pending because they cannot be processed as long as soft interrupts are
disabled and the interrupted code will correctly process them when soft
interrupts are reenabled.
Add a check for softirqs disabled to the pending check to prevent the
warning.
Once the qp has been flushed, it cannot be flushed again. The user qp
flush logic wasn't enforcing it however. The bug can cause
touch-after-free crashes like:
Unable to handle kernel paging request for data at address 0x000001ec
Faulting instruction address: 0xc008000016069100
Oops: Kernel access of bad area, sig: 11 [#1]
...
NIP [c008000016069100] flush_qp+0x80/0x480 [iw_cxgb4]
LR [c00800001606cd6c] c4iw_modify_qp+0x71c/0x11d0 [iw_cxgb4]
Call Trace:
[c00800001606cd6c] c4iw_modify_qp+0x71c/0x11d0 [iw_cxgb4]
[c00800001606e868] c4iw_ib_modify_qp+0x118/0x200 [iw_cxgb4]
[c0080000119eae80] ib_security_modify_qp+0xd0/0x3d0 [ib_core]
[c0080000119c4e24] ib_modify_qp+0xc4/0x2c0 [ib_core]
[c008000011df0284] iwcm_modify_qp_err+0x44/0x70 [iw_cm]
[c008000011df0fec] destroy_cm_id+0xcc/0x370 [iw_cm]
[c008000011ed4358] rdma_destroy_id+0x3c8/0x520 [rdma_cm]
[c0080000134b0540] ucma_close+0x90/0x1b0 [rdma_ucm]
[c000000000444da4] __fput+0xe4/0x2f0
So fix flush_qp() to only flush the wq once.
Cc: stable@vger.kernel.org Signed-off-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The PCIE I/O and MEM resource allocation mechanism is that root bus
goes through the following steps:
1. Check PCI bridges' range and computes I/O and Mem base/limits.
2. Sort all subordinate devices I/O and MEM resource requirements and
allocate the resources and writes/updates subordinate devices'
requirements to PCI bridges I/O and Mem MEM/limits registers.
Currently, PCI Aardvark driver only handles the second step and lacks
the first step, so there is an I/O and MEM resource allocation failure
when using a PCI switch. This commit fixes that by sizing bridges
before doing the resource allocation.
When a task which previously ran on a given CPU is remotely queued to
wake up on that same CPU, there is a period where the task's state is
TASK_WAKING and its vruntime is not normalized. This is not accounted
for in vruntime_normalized() which will cause an error in the task's
vruntime if it is switched from the fair class during this time.
For example if it is boosted to RT priority via rt_mutex_setprio(),
rq->min_vruntime will not be subtracted from the task's vruntime but
it will be added again when the task returns to the fair class. The
task's vruntime will have been erroneously doubled and the effective
priority of the task will be reduced.
Note this will also lead to inflation of all vruntimes since the doubled
vruntime value will become the rq's min_vruntime when other tasks leave
the rq. This leads to repeated doubling of the vruntime and priority
penalty.
Fix this by recognizing a WAKING task's vruntime as normalized only if
sched_remote_wakeup is true. This indicates a migration, in which case
the vruntime would have been normalized in migrate_task_rq_fair().
Based on a similar patch from John Dias <joaodias@google.com>.
Suggested-by: Peter Zijlstra <peterz@infradead.org> Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com> Signed-off-by: Steve Muckle <smuckle@google.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Chris Redpath <Chris.Redpath@arm.com> Cc: John Dias <joaodias@google.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Miguel de Dios <migueldedios@google.com> Cc: Morten Rasmussen <Morten.Rasmussen@arm.com> Cc: Patrick Bellasi <Patrick.Bellasi@arm.com> Cc: Paul Turner <pjt@google.com> Cc: Quentin Perret <quentin.perret@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Todd Kjos <tkjos@google.com> Cc: kernel-team@android.com Fixes: b5179ac70de8 ("sched/fair: Prepare to fix fairness problems on migration") Link: http://lkml.kernel.org/r/20180831224217.169476-1-smuckle@google.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Marking mmp bh dirty before writing it will make writeback
pick up mmp block later and submit a write, we don't want the
duplicate write as kmmpd thread should have full control of
reading and writing the mmp block.
Another reason is we will also have random I/O error on
the writeback request when blk integrity is enabled, because
kmmpd could modify the content of the mmp block(e.g. setting
new seq and time) while the mmp block is under I/O requested
by writeback.
Signed-off-by: Li Dongyang <dongyangli@ddn.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Andreas Dilger <adilger@dilger.ca> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
An online resize of a file system with the bigalloc feature enabled
and a 1k block size would be refused since ext4_resize_begin() did not
understand s_first_data_block is 0 for all bigalloc file systems, even
when the block size is 1k.
Avoid growing the file system to an extent so that the last block
group is too small to hold all of the metadata that must be stored in
the block group.
This problem can be triggered with the following reproducer:
When mounting the superblock, ext4_fill_super() calculates the free
blocks and free inodes and stores them in the superblock. It's not
strictly necessary, since we don't use them any more, but it's nice to
keep them roughly aligned to reality.
Since it's not critical for file system correctness, the code doesn't
call ext4_commit_super(). The problem is that it's in
ext4_commit_super() that we recalculate the superblock checksum. So
if we're not going to call ext4_commit_super(), we need to call
ext4_superblock_csum_set() to make sure the superblock checksum is
consistent.
Most of the time, this doesn't matter, since we end up calling
ext4_commit_super() very soon thereafter, and definitely by the time
the file system is unmounted. However, it doesn't work in this
sequence:
A specially crafted file system can trick empty_inline_dir() into
reading past the last valid entry in a inline directory, and then run
into the end of xattr marker. This will trigger a divide by zero
fault. Fix this by using the size of the inline directory instead of
dir->i_size.
Also clean up error reporting in __ext4_check_dir_entry so that the
message is clearer and more understandable --- and avoids the division
by zero trap if the size passed in is zero. (I'm not sure why we
coded it that way in the first place; printing offset % size is
actually more confusing and less useful.)
If the destination of the rename(2) system call exists, the inode's
link count (i_nlinks) must be non-zero. If it is, the inode can end
up on the orphan list prematurely, leading to all sorts of hilarity,
including a use-after-free.
This fixes a NULL pointer dereference that can happen if the UDL
driver is unloaded before the framebuffer is initialized. This can
happen e.g. if the USB device is unplugged right after it was plugged
in.
As explained by Stéphane Marchesin:
It happens when fbdev is disabled (which is the case for Chrome OS).
Even though intialization of the fbdev part is optional (it's done in
udlfb_create which is the callback for fb_probe()), the teardown isn't
optional (udl_driver_unload -> udl_fbdev_cleanup ->
udl_fbdev_destroy).
Note that udl_fbdev_cleanup *tries* to be conditional (you can see it
does if (!udl->fbdev)) but that doesn't work, because udl->fbdev is
always set during udl_fbdev_init.
Cc: stable@vger.kernel.org Suggested-by: Sean Paul <seanpaul@chromium.org> Reviewed-by: Sean Paul <seanpaul@chromium.org> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Emil Lundmark <lndmrk@chromium.org> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20180528142711.142466-1-lndmrk@chromium.org Signed-off-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When there's no scaling requested ->is_unity should be true no matter
the format.
Also, when no scaling is requested and we have a multi-planar YUV
format, we should leave ->y_scaling[0] to VC4_SCALING_NONE and only
set ->x_scaling[0] to VC4_SCALING_PPF.
Doing this fixes an hardly visible artifact (seen when using modetest
and a rather big overlay plane in YUV420).
Fixes: fc04023fafec ("drm/vc4: Add support for YUV planes.") Cc: <stable@vger.kernel.org> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Reviewed-by: Eric Anholt <eric@anholt.net> Link: https://patchwork.freedesktop.org/patch/msgid/20180725122907.13702-1-boris.brezillon@bootlin.com Signed-off-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On most systems with ACPI hotplugging support, it seems that we always
receive a hotplug event once we re-enable EC interrupts even if the GPU
hasn't even been resumed yet.
This can cause problems since even though we schedule hpd_work to handle
connector reprobing for us, hpd_work synchronizes on
pm_runtime_get_sync() to wait until the device is ready to perform
reprobing. Since runtime suspend/resume callbacks are disabled before
the PM core calls ->suspend(), any calls to pm_runtime_get_sync() during
this period will grab a runtime PM ref and return immediately with
-EACCES. Because we schedule hpd_work from our ACPI HPD handler, and
hpd_work synchronizes on pm_runtime_get_sync(), this causes us to launch
a connector reprobe immediately even if the GPU isn't actually resumed
just yet. This causes various warnings in dmesg and occasionally, also
prevents some displays connected to the dedicated GPU from coming back
up after suspend. Example:
So, to fix this we attempt to grab a runtime PM reference in the ACPI
handler itself asynchronously. If the GPU is already awake (it will have
normal hotplugging at this point) or runtime PM callbacks are currently
disabled on the device, we drop our reference without updating the
autosuspend delay. We only schedule connector reprobes when we
successfully managed to queue up a resume request with our asynchronous
PM ref.
This also has the added benefit of preventing redundant connector
reprobes from ACPI while the GPU is runtime resumed!
Signed-off-by: Lyude Paul <lyude@redhat.com> Cc: stable@vger.kernel.org Cc: Karol Herbst <kherbst@redhat.com>
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1477182#c41 Signed-off-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
It's true we can't resume the device from poll workers in
nouveau_connector_detect(). We can however, prevent the autosuspend
timer from elapsing immediately if it hasn't already without risking any
sort of deadlock with the runtime suspend/resume operations. So do that
instead of entirely avoiding grabbing a power reference.
Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Karol Herbst <kherbst@redhat.com> Acked-by: Daniel Vetter <daniel@ffwll.ch> Cc: stable@vger.kernel.org Cc: Lukas Wunner <lukas@wunner.de> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Turns out this part is my fault for not noticing when reviewing 9a2eba337cace ("drm/nouveau: Fix drm poll_helper handling"). Currently
we call drm_kms_helper_poll_enable() from nouveau_display_hpd_work().
This makes basically no sense however, because that means we're calling
drm_kms_helper_poll_enable() every time we schedule the hotplug
detection work. This is also against the advice mentioned in
drm_kms_helper_poll_enable()'s documentation:
Note that calls to enable and disable polling must be strictly ordered,
which is automatically the case when they're only call from
suspend/resume callbacks.
Of course, hotplugs can't really be ordered. They could even happen
immediately after we called drm_kms_helper_poll_disable() in
nouveau_display_fini(), which can lead to all sorts of issues.
Additionally; enabling polling /after/ we call
drm_helper_hpd_irq_event() could also mean that we'd miss a hotplug
event anyway, since drm_helper_hpd_irq_event() wouldn't bother trying to
probe connectors so long as polling is disabled.
So; simply move this back into nouveau_display_init() again. The race
condition that both of these patches attempted to work around has
already been fixed properly in
d61a5c106351 ("drm/nouveau: Fix deadlock on runtime suspend")
Fixes: 9a2eba337cace ("drm/nouveau: Fix drm poll_helper handling") Signed-off-by: Lyude Paul <lyude@redhat.com> Acked-by: Karol Herbst <kherbst@redhat.com> Acked-by: Daniel Vetter <daniel@ffwll.ch> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Ujfalusi <peter.ujfalusi@ti.com> Cc: stable@vger.kernel.org Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently, there's nothing in nouveau that actually cancels this work
struct. So, cancel it on suspend/unload. Otherwise, if we're unlucky
enough hpd_work might try to keep running up until the system is
suspended.
Signed-off-by: Lyude Paul <lyude@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When we disable hotplugging on the GPU, we need to be able to
synchronize with each connector's hotplug interrupt handler before the
interrupt is finally disabled. This can be a problem however, since
nouveau_connector_detect() currently grabs a runtime power reference
when handling connector probing. This will deadlock the runtime suspend
handler like so:
[ 861.559507] NMI backtrace for cpu 2
[ 861.560363] CPU: 2 PID: 64 Comm: khungtaskd Tainted: G O 4.18.0-rc6Lyude-Test+ #1
[ 861.561197] Hardware name: LENOVO 20EQS64N0B/20EQS64N0B, BIOS N1EET78W (1.51 ) 05/18/2018
[ 861.561948] Call Trace:
[ 861.562757] dump_stack+0x8e/0xd3
[ 861.563516] nmi_cpu_backtrace.cold.3+0x14/0x5a
[ 861.564269] ? lapic_can_unplug_cpu.cold.27+0x42/0x42
[ 861.565029] nmi_trigger_cpumask_backtrace+0xa1/0xae
[ 861.565789] arch_trigger_cpumask_backtrace+0x19/0x20
[ 861.566558] watchdog+0x316/0x580
[ 861.567355] kthread+0x12b/0x150
[ 861.568114] ? reset_hung_task_detector+0x20/0x20
[ 861.568863] ? kthread_create_worker_on_cpu+0x70/0x70
[ 861.569598] ret_from_fork+0x3a/0x50
[ 861.570370] Sending NMI from CPU 2 to CPUs 0-1,3-7:
[ 861.571426] NMI backtrace for cpu 6 skipped: idling at intel_idle+0x7f/0x120
[ 861.571429] NMI backtrace for cpu 7 skipped: idling at intel_idle+0x7f/0x120
[ 861.571432] NMI backtrace for cpu 3 skipped: idling at intel_idle+0x7f/0x120
[ 861.571464] NMI backtrace for cpu 5 skipped: idling at intel_idle+0x7f/0x120
[ 861.571467] NMI backtrace for cpu 0 skipped: idling at intel_idle+0x7f/0x120
[ 861.571469] NMI backtrace for cpu 4 skipped: idling at intel_idle+0x7f/0x120
[ 861.571472] NMI backtrace for cpu 1 skipped: idling at intel_idle+0x7f/0x120
[ 861.572428] Kernel panic - not syncing: hung_task: blocked tasks
So: fix this by making it so that normal hotplug handling /only/ happens
so long as the GPU is currently awake without any pending runtime PM
requests. In the event that a hotplug occurs while the device is
suspending or resuming, we can simply defer our response until the GPU
is fully runtime resumed again.
Changes since v4:
- Use a new trick I came up with using pm_runtime_get() instead of the
hackish junk we had before
Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Karol Herbst <kherbst@redhat.com> Acked-by: Daniel Vetter <daniel@ffwll.ch> Cc: stable@vger.kernel.org Cc: Lukas Wunner <lukas@wunner.de> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
While reading block, it is possible that io error return due to underlying
storage issue, in this case, BH_NeedsValidate was left in the buffer head.
Then when reading the very block next time, if it was already linked into
journal, that will trigger the following panic.
projects / mirror_ubuntu-bionic-kernel.git / log