Yuval Mintz [Wed, 11 May 2016 13:36:19 +0000 (16:36 +0300)]
qede: Add VF support
Adding a PCI callback for `sriov_configure' and a new PCI device id for
the VF [+ Some minor changes to accomodate differences between PF and VF
at the qede].
Following this, VF creation should be possible and the entire subset of
existing PF functionality that's allow to VFs should be supported.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Wed, 11 May 2016 13:36:18 +0000 (16:36 +0300)]
qed: Align TLVs
As the VF infrastructure is supposed to offer backward/forward
compatibility, the various types associated with VF<->PF communication
should be aligned across all various platforms that support IOV
on our family of adapters.
This adds a couple of currently missing values, specifically aligning
the enum for the various TLVs possible in the communication between them.
It then adds the PF implementation for some of those missing VF requests.
This support isn't really necessary for the Linux VF as those VFs aren't
requiring it [at least today], but are required by VFs running on other
OSes. LRO is an example of one such configuration.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Wed, 11 May 2016 13:36:17 +0000 (16:36 +0300)]
qed: Bulletin and Link
Up to this point, VF and PF communication always originates from VF.
As a result, VF cannot be notified of any async changes, and specifically
cannot be informed of the current link state.
This introduces the bulletin board, the mechanism through which the PF
is going to communicate async notifications back to the VF. basically,
it's a well-defined structure agreed by both PF and VF which the VF would
continuously poll and into which the PF would DMA messages when needed.
[Bulletin board is actually allocated and communicated in previous patches
but never before used]
Based on the bulletin infrastructure, the VF can query its link status
and receive said async carrier changes.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Wed, 11 May 2016 13:36:16 +0000 (16:36 +0300)]
qed: IOV l2 functionality
This adds sufficient changes to allow VFs l2-configuration flows to work.
While the fastpath of the VF and the PF are meant to be exactly the same,
the configuration of the VF is done by the PF.
This diverges all VF-related configuration flows that originate from a VF,
making them pass through the VF->PF channel and adding sufficient logic
on the PF side to support them.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Wed, 11 May 2016 13:36:15 +0000 (16:36 +0300)]
qed: IOV configure and FLR
While previous patches have already added the necessary logic to probe
VFs as well as enabling them in the HW, this patch adds the ability to
support VF FLR & SRIOV disable.
It then wraps both flows together into the first IOV callback to be
provided to the protocol driver - `configure'. This would later to be used
to enable and disable SRIOV in the adapter.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Wed, 11 May 2016 13:36:14 +0000 (16:36 +0300)]
qed: Introduce VFs
This adds the qed VFs for the first time -
The vfs are limited functions, with a very different PCI bar structure
[when compared with PFs] to better impose the related security demands
associated with them.
This patch includes the logic neccesary to allow VFs to successfully probe
[without actually adding the ability to enable iov].
This includes diverging all the flows that would occur as part of the pci
probe of the driver, preventing VF from accessing registers/memories it
can't and instead utilize the VF->PF channel to query the PF for needed
information.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Wed, 11 May 2016 13:36:13 +0000 (16:36 +0300)]
qed: Add VF->PF channel infrastructure
Communication between VF and PF is based on a dedicated HW channel;
VF will prepare a messge, and by signaling the HW the PF would get a
notification of that message existance. The PF would then copy the
message, process it and DMA an answer back to the VF as a response.
The messages themselves are TLV-based - allowing easier backward/forward
compatibility.
This patch adds the infrastructure of the channel on the PF side -
starting with the arrival of the notification and ending with DMAing
the response back to the VF.
It also adds a dummy-response as reference, as it only lays the
groundwork of the communication; it doesn't really add support of any
actual messages.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Wed, 11 May 2016 13:36:12 +0000 (16:36 +0300)]
qed: Add CONFIG_QED_SRIOV
Add support for a new Kconfig option for qed* driver which would allow
[eventually] the support in VFs.
This patch adds the necessary logic in the PF to learn about the possible
VFs it will have to support [Based on PCI configuration space and HW],
and prepare a database with an entry per-VF as infrastructure for future
interaction with said VFs.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 12 May 2016 00:00:54 +0000 (20:00 -0400)]
Merge tag 'nfc-next-4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz says:
====================
NFC 4.7 pull request
This is the first NFC pull request for 4.7. With this one we
mainly have:
- Support for NXP's pn532 NFC chipset. The pn532 is based on the same
microcontroller as the pn533, but it talks to the host through i2c
instead of USB. By separating the pn533 driver into core and PHY
parts, we can not add the i2c layer and support the pn532 chipset.
- Support for NCI's loopback mode. This is a testing mode where each
packet received by the NFCC is sent back to the DH, allowing the
host to test that the controller can receive and send data.
- A few ACPI related fixes for the STMicro drivers, in order to match
the device tree naming scheme.
- A bunch of cleanups for the st-nci and the st21nfca STMicro drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
CQE Compressing reduces PCI overhead by coalescing and compressing multiple CQEs into a
single merged CQE. Successful compressing improves message rate especially for small packet
traffic.
CQE Compressing in details:
Instead of writing full CQEs to memory, multiple almost identical CQEs are merged and compressed.
Information that is shared between the CQEs is written once, regardless of the number of
compressed CQEs. In addition, only the unique information (small amount of bytes compared to
full CQE size) is written per CQE.
CQE Compression Block:
This block contains multiple compressed CQEs. CQE Compression Block contains a single copy
of CQEs properties which are shared between all the compressed CQEs (called Title, see below)
and multiple mini CQEs (CQEs in compressed form).
Title:
The Title holds information which is shared between all the compressed CQEs in the CQE Compression
Block. In each Compression Block there is only a single Title regardless of the number
of compressed CQEs.
Mini CQE:
A CQE in compressed form that holds some data needed to extract a single full CQE, for example
8 Bytes instead of 64 Bytes.
The shared information between all compressed CQEs, which belong to the same CQE Compression
Block called Title, is written once, and only the unique information in each compressed
CQE, for example 8 bytes, is written per compressed CQE, called mini CQE.
Since CQE Compression can add overhead to the software (CPU),
it will be only enabled on "weak/slow" PCI slots, where it can actually help.
Saeed Mahameed [Tue, 10 May 2016 21:29:16 +0000 (00:29 +0300)]
net/mlx5e: Enable CQE compression when PCI is slower than link
We turn the feature ON, only for servers with PCI BW < MAX LINK BW, as it
helps reducing PCI pressure on weak PCI slots, but it adds some software
overhead.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Tue, 10 May 2016 21:29:15 +0000 (00:29 +0300)]
net/mlx5e: Expand WQE stride when CQE compression is enabled
Make the MPWQE/Striding RQ default configuration dynamic and not
statically set at compile time. Now at driver load we set
stride size and num strides dynamically.
By default we use same values as before, but when CQE compression
is enabled, we set larger stride size to benefit from CQE
compression for larger packets.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Tue, 10 May 2016 21:29:14 +0000 (00:29 +0300)]
net/mlx5e: CQE compression
CQE compression feature is meant to save PCIe bandwidth by
compressing few CQEs into smaller amount of bytes on PCIe.
CQE compression can be selectively enabled per CQ. By default
is disabled for now and will be enabled later on.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 11 May 2016 23:36:29 +0000 (19:36 -0400)]
Merge branch 'more-dsa-probing'
Andrew Lunn says:
====================
More enabler patches for DSA probing
The complete set of patches for the reworked DSA probing is too big to
post as once. These subset contains some enablers which are easy to
review.
Eventually, the Marvell driver will instantiate its own internal MDIO
bus, rather than have the framework do it, thus allows devices on the
bus to be listed in the device tree. Initialize the main mutex as soon
as it is created, to avoid lifetime issues with the mdio bus.
A previous patch renamed all the DSA probe functions to make room for
a true device probe. However the recent merging of all the Marvell
switch drivers resulted in mv88e6xxx going back to the old probe
name. Rename it again, so we can have a driver probe function.
Add minimum support for the Marvell switch driver to probe as an MDIO
device, as well as an DSA driver. Later patches will then register
this device with the new DSA core framework.
Move the GPIO reset code out of the DSA code. Different drivers may
need different reset mechanisms, e.g. via a reset controller for
memory mapped devices. Don't clutter up the core with this. Let each
driver implement what it needs.
master_dev is no longer needed in the switch drivers, since they have
access to a device pointer from the probe function. Remove it.
Let the switch parse the eeprom length from its one device tree
node. This is required with the new binding when the central DSA
platform device no longer exists.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Tue, 10 May 2016 21:27:25 +0000 (23:27 +0200)]
dsa: mv88e6xxx: Handle eeprom-length property
A switch can export an attached EEPROM using the standard ethtool API.
However the switch itself cannot determine the size of the EEPROM, and
multiple sizes are allowed. Thus a device tree property is supported
to indicate the length of the EEPROM. Parse this property during
device probe, and implement a callback function to retrieve it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Tue, 10 May 2016 21:27:24 +0000 (23:27 +0200)]
dsa: Rename switch chip data to cd
The dsa_switch structure contains a dsa_chip_data member called pd.
However in the rest of the code, pd is used for dsa_platform_data.
This is confusing. Rename it cd, which is already often used in dsa.c
and slave.c for this data type.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Tue, 10 May 2016 21:27:23 +0000 (23:27 +0200)]
dsa: Remove master_dev from switch structure
The switch drivers only use the master_dev member for dev_info()
messages. Now that the device is passed to the old style probe, and
new style drivers are probed as true linux drivers, this is no longer
needed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Tue, 10 May 2016 21:27:22 +0000 (23:27 +0200)]
dsa: Move gpio reset into switch driver
Resetting the switch is something the driver does, not the framework.
So move the parsing of this property into the driver.
There are no in kernel users of this property, so moving it does not
break anything. There is however a board which will make use of this
property making its way into the kernel.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Tue, 10 May 2016 21:27:21 +0000 (23:27 +0200)]
dsa: Add mdio device support to Marvell switches
Allow Marvell switches to be mdio devices. Currently the driver just
allocate the private structure and detects what device is on the
bus. Later patches will make them register with the DSA framework.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Tue, 10 May 2016 21:27:20 +0000 (23:27 +0200)]
dsa: mv88e6xxx: Rename probe function to fit the normal pattern
All other DSA drivers use _drv_ in there DSA probe function name, thus
allowing for a true linux driver probe function to use the
conventional name. Make mv88e6xxx fit this pattern.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Tue, 10 May 2016 19:44:29 +0000 (15:44 -0400)]
net: dsa: mv88e6xxx: add STU capability
Some switch models have a STU (per VLAN port state database). Add a new
capability flag to switches info, instead of checking their family.
Also if the 6165 family has an STU, it must have a VTU, so add the
MV88E6XXX_FLAG_VTU to its family flags.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Tue, 10 May 2016 19:44:28 +0000 (15:44 -0400)]
net: dsa: mv88e6xxx: abstract VTU/STU data access
Both VTU and STU operations use the same routine to access their
(common) data registers, with a different offset.
Add VTU and STU specific read and write functions to the data registers
to abstract the required offset.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 11 May 2016 23:31:40 +0000 (19:31 -0400)]
Merge branch 'vrf-pktinfo'
David Ahern says:
====================
net: vrf: Fixup PKTINFO to return enslaved device index
Applications such as OSPF and BFD need the original ingress device not
the VRF device; the latter can be derived from the former. To that end
move the packet intercept from an rx handler that is invoked by
__netif_receive_skb_core to the ipv4 and ipv6 receive processing.
IPv6 already saves the skb_iif to the control buffer in ipv6_rcv. Since
the skb->dev has not been switched the cb has the enslaved device. Make
the same happen for IPv4 by adding the skb_iif to inet_skb_parm and set
it in ipv4 code after clearing the skb control buffer similar to IPv6.
From there the pktinfo can just pull it from cb with the PKTINFO_SKB_CB
cast.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 10 May 2016 18:19:51 +0000 (11:19 -0700)]
net: original ingress device index in PKTINFO
Applications such as OSPF and BFD need the original ingress device not
the VRF device; the latter can be derived from the former. To that end
add the skb_iif to inet_skb_parm and set it in ipv4 code after clearing
the skb control buffer similar to IPv6. From there the pktinfo can just
pull it from cb with the PKTINFO_SKB_CB cast.
The previous patch moving the skb->dev change to L3 means nothing else
is needed for IPv6; it just works.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 10 May 2016 18:19:50 +0000 (11:19 -0700)]
net: l3mdev: Add hook in ip and ipv6
Currently the VRF driver uses the rx_handler to switch the skb device
to the VRF device. Switching the dev prior to the ip / ipv6 layer
means the VRF driver has to duplicate IP/IPv6 processing which adds
overhead and makes features such as retaining the ingress device index
more complicated than necessary.
This patch moves the hook to the L3 layer just after the first NF_HOOK
for PRE_ROUTING. This location makes exposing the original ingress device
trivial (next patch) and allows adding other NF_HOOKs to the VRF driver
in the future.
dev_queue_xmit_nit is exported so that the VRF driver can cycle the skb
with the switched device through the packet taps to maintain current
behavior (tcpdump can be used on either the vrf device or the enslaved
devices).
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Tue, 10 May 2016 14:08:17 +0000 (16:08 +0200)]
ipv6: fix 4in6 tunnel receive path
Protocol for 4in6 tunnel is IPPROTO_IPIP. This was wrongly changed by
the last cleanup.
CC: Tom Herbert <tom@herbertland.com> Fixes: 0d3c703a9d17 ("ipv6: Cleanup IPv6 tunnel receive path") Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lawrence Brakmo [Wed, 11 May 2016 17:02:13 +0000 (10:02 -0700)]
tcp: replace cnt & rtt with struct in pkts_acked()
Replace 2 arguments (cnt and rtt) in the congestion control modules'
pkts_acked() function with a struct. This will allow adding more
information without having to modify existing congestion control
modules (tcp_nv in particular needs bytes in flight when packet
was sent).
As proposed by Neal Cardwell in his comments to the tcp_nv patch.
Signed-off-by: Lawrence Brakmo <brakmo@fb.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 11 May 2016 03:36:14 +0000 (23:36 -0400)]
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
Included changes:
- remove useless skb size check in batadv_interface_rx
- basic netns support introduced by Andrew Lunn:
- prevent virtual interface from changing netns by setting
NETIF_F_NETNS_LOCAL
- create virtual interface within the netns of the first
hard-interface
- introduce detection of complex bridge loops and report event
to the user (via udev) when the Bridge Loop Avoidance mechanism
can't prevent them
- minor reference counting bugfixes for the hard_iface object that
couldn't make it via the net tree
- use kref_get() instead of kref_get_unless_zero() to make reference
counting bug more visible
- use batadv_compare_eth() all over the code when possible instead of
plain memcmp()
- minor code cleanup and style adjustments
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini Varadhan [Tue, 10 May 2016 16:38:08 +0000 (12:38 -0400)]
skbuff: remove unused variable `doff'
There are two instances of an unused variable, `doff' added by
commit 6fa01ccd8830 ("skbuff: Add pskb_extract() helper function")
in pskb_carve_inside_header() and pskb_carve_inside_nonlinear().
Remove these instances, they are not used.
Reported by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Tue, 10 May 2016 09:56:32 +0000 (11:56 +0200)]
ila: ipv6/ila: fix nlsize calculation for lwtunnel
The handler 'ila_fill_encap_info' adds two attributes: ILA_ATTR_LOCATOR
and ILA_ATTR_CSUM_MODE.
nla_total_size_64bit() must be use for ILA_ATTR_LOCATOR.
Also, do nla_put_u8 instead of nla_put_u64 for ILA_ATTR_CSUM_MODE.
Fixes: f13a82d87b21 ("ipv6: use nla_put_u64_64bit()") Fixes: 90bfe662db13 ("ila: add checksum neutral ILA translations") Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira [Tue, 10 May 2016 19:33:38 +0000 (21:33 +0200)]
gtp: reload GTPv1 header after pskb_may_pull()
The GTPv1 header flags indicate the presence of optional extensions
after this header. Refresh the pointer to the GTPv1 header as skb->head
might have be reallocated via pskb_may_pull().
Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)") Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Mon, 9 May 2016 09:40:20 +0000 (11:40 +0200)]
block/drbd: align properly u64 in nl messages
The attribute 0 is never used in drbd, so let's use it as pad attribute
in netlink messages. This minimizes the patch.
Note that this patch is only compile-tested.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool callbacks {get|set}_link_ksettings may be the
same for many drivers. So we add two generics callbacks
phy_ethtool_{get|set}_link_ksettings.
To use those generics callbacks, the ethernet driver must
use the pointer phydev contained in struct net_device, and
not use a private structure to store this pointer.
Changelog:
v3:
- rename function to phy_ethtool_{get|set}_link_ksettings
- move code to net/phy/phy.c
This feedback were provided by David Decotigny
v2:
- use generic function instead of macro
- ethernet driver use the pointer phydev provided by struct net_device
Those idea were provided by Ben Hutchings,
and Florian Fainelli acknowledge them.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes [Mon, 9 May 2016 22:19:42 +0000 (00:19 +0200)]
net: ethernet: fec: use phydev from struct net_device
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the one
contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool callbacks {get|set}_link_ksettings are often the same, so
we add two generics functions phy_ethtool_{get|set}_link_ksettings
to avoid writing severals times the same function.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Acked-By: David Decotigny <decot@googlers.com> Signed-off-by: David S. Miller <davem@davemloft.net>
this is a pull request of 12 patches for net-next/master.
Alexander Gerasiov and Nikita Edward Baruzdin each contribute a patch
improving the sja1000 driver. Amitoj Kaur Chawla's patch converts the
mcp251x driver to alloc_workqueue(). A patch by Oliver Hartkopp fixes
the handling of CAN config options. Andreas Gröger improves the error
handling in the janz-ican3 driver. The patch by Maximilian Schneider
for the gs_usb improves probing of the USB driver. Finally there are 6
improvement patches by Marek Vasut for the ifi CAN driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira [Sun, 8 May 2016 22:55:48 +0000 (00:55 +0200)]
gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)
This is an initial implementation of a netdev driver for GTP datapath
(GTP-U) v0 and v1, according to the GSM TS 09.60 and 3GPP TS 29.060
standards. This tunneling protocol is used to prevent subscribers from
accessing mobile carrier core network infrastructure.
This implementation requires a GGSN userspace daemon that implements the
signaling protocol (GTP-C), such as OpenGGSN [1]. This userspace daemon
updates the PDP context database that represents active subscriber
sessions through a genetlink interface.
For more context on this tunneling protocol, you can check the slides
that were presented during the NetDev 1.1 [2].
When comparing Ethernet address it is better to use the more
generic batadv_compare_eth. The latter is also optimised for
architectures having a fast unaligned access.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
[sven@narfation.org: fix conflicts with current version] Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Marek Lindner [Sun, 20 Mar 2016 10:39:56 +0000 (18:39 +0800)]
batman-adv: replace ethertype variable with ETH_P_BATMAN for readability
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Reviewed-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Mon, 22 Feb 2016 20:02:39 +0000 (21:02 +0100)]
batman-adv: Use bool as return type for boolean functions
It is easier to understand that the returned value of a specific function
doesn't have to be 0 when the functions was successful when the actual
return type is bool. This is especially true when all surrounding functions
with return type int use negative values to return the error code.
Reported-by: Nicholas Krause <xerofoify@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sat, 5 Mar 2016 18:05:24 +0000 (19:05 +0100)]
batman-adv: Use kref_get for _batadv_update_route
_batadv_update_route requires that the caller already has a valid reference
for neigh_node. It is therefore not possible that it has an reference
counter of 0 and was still given to this function
The kref_get function instead WARNs (with debug information) when the
reference counter would still be 0. This makes a bug in batman-adv better
visible because kref_get_unless_zero would have ignored this problem.
Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Mon, 11 Apr 2016 11:06:40 +0000 (13:06 +0200)]
batman-adv: Use kref_get for hard_iface subfunctions
The callers of the functions using batadv_hard_iface objects already make
sure that they hold a valid reference. The subfunctions don't have
to check whether the reference counter is > 0 because this was checked by
the callers.
The kref_get function instead WARNs (with debug information) when the
reference counter would still be 0. This makes a bug in batman-adv better
visible because kref_get_unless_zero would have ignored this problem.
Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sat, 5 Mar 2016 15:09:23 +0000 (16:09 +0100)]
batman-adv: Use kref_get for batadv_gw_node_add
batadv_gw_node_add requires that the caller already has a valid reference
for orig_node. It is therefore not possible that it has an reference
counter of 0 and was still given to this function
The kref_get function instead WARNs (with debug information) when the
reference counter would still be 0. This makes a bug in batman-adv better
visible because kref_get_unless_zero would have ignored this problem.
Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sat, 5 Mar 2016 15:09:22 +0000 (16:09 +0100)]
batman-adv: Use kref_get for batadv_gw_select
batadv_gw_select requires that the caller already has a valid reference for
new_gw_node. It is therefore not possible that it has an reference counter
of 0 and was still given to this function
The kref_get function instead WARNs (with debug information) when the
reference counter would still be 0. This makes a bug in batman-adv better
visible because kref_get_unless_zero would have ignored this problem.
Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sat, 5 Mar 2016 15:09:21 +0000 (16:09 +0100)]
batman-adv: Use kref_get for batadv_nc_get_nc_node
batadv_nc_get_nc_node requires that the caller already has a valid
reference for orig_neigh_node. It is therefore not possible that it has an
reference counter of 0 and was still given to this function
The kref_get function instead WARNs (with debug information) when the
reference counter would still be 0. This makes a bug in batman-adv better
visible because kref_get_unless_zero would have ignored this problem.
Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sat, 5 Mar 2016 15:09:20 +0000 (16:09 +0100)]
batman-adv: Use kref_get for batadv_tvlv_container_get
batadv_tvlv_container_get requires that tvlv.container_list_lock is held by
the caller. It is therefore not possible that an item in
tvlv.container_list has an reference counter of 0 and is still in the list
The kref_get function instead WARNs (with debug information) when the
reference counter would still be 0. This makes a bug in batman-adv better
visible because kref_get_unless_zero would have ignored this problem.
Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sat, 5 Mar 2016 15:09:18 +0000 (16:09 +0100)]
batman-adv: Increase hard_iface refcnt for ptype
The hard_iface is referenced in the packet_type for batman-adv. Increase
the refcounter of the hard_interface for it to have an explicit reference
for it in case this functionality gets refactorted and the currently
used implicit reference for it will be removed.
Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sat, 5 Mar 2016 15:09:17 +0000 (16:09 +0100)]
batman-adv: Check hard_iface refcnt when receiving skb
The receive function may start processing an incoming packet while the
hard_iface is shut down in a different context. All called functions called
with the batadv_hard_iface object belonging to the incoming interface would
have to check whether the reference counter is still > 0.
This is rather error-prone because this check can be forgotten easily.
Instead check the reference counter when receiving the object to make sure
that all called functions have a valid reference.
Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sat, 5 Mar 2016 15:09:16 +0000 (16:09 +0100)]
batman-adv: Check hard_iface refcnt before calling function
The batadv_hardif_list list is checked in many situations and the items
in this list are given to specialized functions to modify the routing
behavior. At the moment each of these called functions has to check
itself whether the received batadv_hard_iface has a refcount > 0 before
it can increase the reference counter and use it in other objects.
This can easily lead to problems because it is not easily visible where
all callers of a function got the batadv_hard_iface object from and
whether they already hold a valid reference.
Checking the reference counter directly before calling a subfunction
with a pointer from the batadv_hardif_list avoids this problem.
Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc>
Simon Wunderlich [Sat, 12 Mar 2016 09:49:33 +0000 (10:49 +0100)]
batman-adv: add detection for complex bridge loops
There are network setups where the current bridge loop avoidance can't
detect bridge loops. The minimal setup affected would consist of two
LANs and two separate meshes, connected in a ring like that:
Since both the meshes and backbones are separate, the bridge loop
avoidance has not enough information to detect and avoid the loop
in this case. Even if these scenarios can't be fixed easily,
these kind of loops can be detected.
This patch implements a periodic check (running every 60 seconds for
now) which sends a broadcast frame with a random MAC address on
each backbone VLAN. If a broadcast frame with the same MAC address
is received shortly after on the mesh, we know that there must be a
loop and report that incident as well as throw an uevent to let others
handle that problem.
Signed-off-by: Simon Wunderlich <simon.wunderlich@open-mesh.com>
[sven@narfation.org: fix conflicts with current version] Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc>
Andrew Lunn [Thu, 21 Apr 2016 10:57:27 +0000 (12:57 +0200)]
batman-adv: Create batman soft interfaces within correct netns.
When creating a soft interface, create it in the same netns as the
hard interface. Replace all references to init_net with the correct
name space for the interface being manipulated.
Suggested-by: Daniel Ehlers <danielehlers@mindeye.net> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Antonio Quartulli <a@unstable.cc> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc>
Andrew Lunn [Tue, 1 Mar 2016 21:19:05 +0000 (22:19 +0100)]
batman-adv: NETIF_F_NETNS_LOCAL feature to prevent netns moves
The batX soft interface should not be moved between network name
spaces. This is similar to bridges, bonds, tunnels, which are not
allowed to move between network namespaces.
Suggested-by: Daniel Ehlers <danielehlers@mindeye.net> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Antonio Quartulli <a@unstable.cc> Reviewed-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sun, 28 Feb 2016 10:38:52 +0000 (11:38 +0100)]
batman-adv: Remove hdr_size skb size check in batadv_interface_rx
The callers of batadv_interface_rx have to make sure that enough data can
be pulled from the skb when they read the batman-adv header. The only two
functions using it are either calling pskb_may_pull with hdr_size directly
(batadv_recv_bcast_packet) or indirectly via batadv_check_unicast_packet
(batadv_recv_unicast_packet).
Reported-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sun, 28 Feb 2016 10:38:51 +0000 (11:38 +0100)]
batman-adv: Remove unused parameter recv_if of batadv_interface_rx
Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc>
A recent commit introduced an unconditional use of an uninitialized
variable, as reported in this gcc warning:
net/netfilter/nf_conntrack_core.c: In function '__nf_conntrack_confirm':
net/netfilter/nf_conntrack_core.c:632:33: error: 'ctinfo' may be used uninitialized in this function [-Werror=maybe-uninitialized]
bytes = atomic64_read(&counter[CTINFO2DIR(ctinfo)].bytes);
^
net/netfilter/nf_conntrack_core.c:628:26: note: 'ctinfo' was declared here
enum ip_conntrack_info ctinfo;
The problem is that a local variable shadows the function parameter.
This removes the local variable, which looks like what Pablo originally
intended.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 71d8c47fc653 ("netfilter: conntrack: introduce clash resolution on insertion race") Acked-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Tested: Running netperf TCP_STREAM with gretap and keyid configured.
Visually verified that MTU is correctly being set. Did not test HW
offload (Alexander plese try)
====================
Tested-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Tue, 10 May 2016 00:12:08 +0000 (17:12 -0700)]
ip6_gre: Fix MTU setting
In ip6gre_tnl_link_config set t->tun_len and t->hlen correctly for the
configuration. For hard_header_len and mtu calculation include
IPv6 header and encapsulation overhead.
In ip6gre_tunnel_init_common set t->tun_len and t->hlen correctly for
the configuration. Revert to setting hard_header_len instead of
needed_headroom.
Tested:
./ip link add name tun8 type ip6gretap remote \
2401:db00:20:911a:face:0:27:0 local \
2401:db00:20:911a:face:0:25:0 ttl 225
Gives MTU of 1434. That is equal to 1500 - 40 - 14 - 4 - 8.
./ip link add name tun8 type ip6gretap remote \
2401:db00:20:911a:face:0:27:0 local \
2401:db00:20:911a:face:0:25:0 ttl 225 okey 123
Gives MTU of 1430. That is equal to 1500 - 40 - 14 - 4 - 8 - 4.
Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac: dwmac-socfpga: make socfpga_dwmac_pm_ops static
Fix the following sparse warning:
drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c:274:1: warning:
symbol 'socfpga_dwmac_pm_ops' was not declared. Should it be static?
Signed-off-by: Joachim Eastwood <manabian@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 10 May 2016 02:33:53 +0000 (22:33 -0400)]
Merge branch 'l3mdev-send-enslaved'
David Ahern says:
====================
net: l3mdev: Allow send on enslaved interface
First patch preps for the second. The second is required for several use
cases such as ping on an interface and BFD that need to send packets on
a specific interface, including ones enslaved to a VRF device.
v2
- fixed brackets on both patches per comment from DaveM
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Sat, 7 May 2016 23:49:00 +0000 (16:49 -0700)]
net: l3mdev: Allow send on enslaved interface
Allow udp and raw sockets to send by oif that is an enslaved interface
versus the l3mdev/VRF device. For example, this allows BFD to use ifindex
from IP_PKTINFO on a receive to send a response without the need to
convert to the VRF index. It also allows ping and ping6 to work when
specifying an enslaved interface (e.g., ping -I swp1 <ip>) which is
a natural use case.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Sat, 7 May 2016 23:48:59 +0000 (16:48 -0700)]
net: l3mdev: Move get_saddr and rt6_dst
Move l3mdev_rt6_dst_by_oif and l3mdev_get_saddr to l3mdev.c. Collapse
l3mdev_get_rt6_dst into l3mdev_rt6_dst_by_oif since it is the only
user and keep the l3mdev_get_rt6_dst name for consistency with other
hooks.
A follow-on patch adds more code to these functions making them long
for inlined functions.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
NFC: pn533: reset poll modulation list before calling targets_found
We need to reset the poll modulation list before calling
nfc_targets_found because otherwise userspace could run
before the modulation list is cleared and then get a "Cannot
activate target while polling" error upon calling activate_target.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In netdevice.h we removed the structure in net-next that is being
changes in 'net'. In macsec.c and rtnetlink.c we have overlaps
between fixes in 'net' and the u64 attribute changes in 'net-next'.
The mlx5 conflicts have to do with vxlan support dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Check klogctl failure correctly, from Colin Ian King.
2) Prevent OOM when under memory pressure in flowcache, from Steffen
Klassert.
3) Fix info leak in llc and rtnetlink ifmap code, from Kangjie Lu.
4) Memory barrier and multicast handling fixes in bnxt_en, from Michael
Chan.
5) Endianness bug in mlx5, from Daniel Jurgens.
6) Fix disconnect handling in VSOCK, from Ian Campbell.
7) Fix locking of netdev list walking in get_bridge_ifindices(), from
Nikolay Aleksandrov.
8) Bridge multicast MLD parser can look at wrong packet offsets, fix
from Linus Lüssing.
9) Fix chip hang in qede driver, from Sudarsana Reddy Kalluru.
10) Fix missing setting of encapsulation before inner handling completes
in udp_offload code, from Jarno Rajahalme.
11) Missing rollbacks during LAG join and flood configuration failures
in mlxsw driver, from Ido Schimmel.
12) Fix error code checks in netxen driver, from Dan Carpenter.
13) Fix key size in new macsec driver, from Sabrina Dubroca.
14) Fix mlx5/VXLAN dependencies, from Arnd Bergmann.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (29 commits)
net/mlx5e: make VXLAN support conditional
Revert "net/mlx5: Kconfig: Fix MLX5_EN/VXLAN build issue"
macsec: key identifier is 128 bits, not 64
Documentation/networking: more accurate LCO explanation
macvtap: segmented packet is consumed
tools: bpf_jit_disasm: check for klogctl failure
qede: uninitialized variable in qede_start_xmit()
netxen: netxen_rom_fast_read() doesn't return -1
netxen: reversed condition in netxen_nic_set_link_parameters()
netxen: fix error handling in netxen_get_flash_block()
mlxsw: spectrum: Add missing rollback in flood configuration
mlxsw: spectrum: Fix rollback order in LAG join failure
udp_offload: Set encapsulation before inner completes.
udp_tunnel: Remove redundant udp_tunnel_gro_complete().
qede: prevent chip hang when increasing channels
net: ipv6: tcp reset, icmp need to consider L3 domain
bridge: fix igmp / mld query parsing
net: bridge: fix old ioctl unlocked net device walk
VSOCK: do not disconnect socket when peer has shutdown SEND only
net/mlx4_en: Fix endianness bug in IPV6 csum calculation
...
====================
Netfilter updates for net-next
The following large patchset contains Netfilter updates for your
net-next tree. My initial intention was to send you this in two goes but
when I looked back twice I already had this burden on top of me.
Several updates for IPVS from Marco Angaroni:
1) Allow SIP connections originating from real-servers to be load
balanced by the SIP persistence engine as is already implemented
in the other direction.
2) Release connections immediately for One-packet-scheduling (OPS)
in IPVS, instead of making it via timer and rcu callback.
3) Skip deleting conntracks for each one packet in OPS, and don't call
nf_conntrack_alter_reply() since no reply is expected.
4) Enable drop on exhaustion for OPS + SIP persistence.
Miscelaneous conntrack updates from Florian Westphal, including fix for
hash resize:
5) Move conntrack generation counter out of conntrack pernet structure
since this is only used by the init_ns to allow hash resizing.
6) Use get_random_once() from packet path to collect hash random seed
instead of our compound.
7) Don't disable BH from ____nf_conntrack_find() for statistics,
use NF_CT_STAT_INC_ATOMIC() instead.
8) Fix lookup race during conntrack hash resizing.
9) Introduce clash resolution on conntrack insertion for connectionless
protocol.
Then, Florian's netns rework to get rid of per-netns conntrack table,
thus we use one single table for them all. There was consensus on this
change during the NFWS 2015 and, on top of that, it has recently been
pointed as a source of multiple problems from unpriviledged netns:
11) Use a single conntrack hashtable for all namespaces. Include netns
in object comparisons and make it part of the hash calculation.
Adapt early_drop() to consider netns.
12) Use single expectation and NAT hashtable for all namespaces.
13) Use a single slab cache for all namespaces for conntrack objects.
14) Skip full table scanning from nf_ct_iterate_cleanup() if the pernet
conntrack counter tells us the table is empty (ie. equals zero).
Fixes for nf_tables interval set element handling, support to set
conntrack connlabels and allow set names up to 32 bytes.
15) Parse element flags from element deletion path and pass it up to the
backend set implementation.
16) Allow adjacent intervals in the rbtree set type for dynamic interval
updates.
17) Add support to set connlabel from nf_tables, from Florian Westphal.
18) Allow set names up to 32 bytes in nf_tables.
Several x_tables fixes and updates:
19) Fix incorrect use of IS_ERR_VALUE() in x_tables, original patch
from Andrzej Hajda.
And finally, miscelaneous netfilter updates such as:
20) Disable automatic helper assignment by default. Note this proc knob
was introduced by a9006892643a ("netfilter: nf_ct_helper: allow to
disable automatic helper assignment") 4 years ago to start moving
towards explicit conntrack helper configuration via iptables CT
target.
21) Get rid of obsolete and inconsistent debugging instrumentation
in x_tables.
22) Remove unnecessary check for null after ip6_route_output().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Josh Poimboeuf [Fri, 6 May 2016 14:22:25 +0000 (09:22 -0500)]
compiler-gcc: require gcc 4.8 for powerpc __builtin_bswap16()
gcc support for __builtin_bswap16() was supposedly added for powerpc in
gcc 4.6, and was then later added for other architectures in gcc 4.8.
However, Stephen Rothwell reported that attempting to use it on powerpc
in gcc 4.6 fails with:
lib/vsprintf.c:160:2: error: initializer element is not constant
lib/vsprintf.c:160:2: error: (near initialization for 'decpair[0]')
lib/vsprintf.c:160:2: error: initializer element is not constant
lib/vsprintf.c:160:2: error: (near initialization for 'decpair[1]')
...
I'm not entirely sure what those errors mean, but I don't see them on
gcc 4.8. So let's consider gcc 4.8 to be the official starting point
for __builtin_bswap16().
Arnd Bergmann adds:
"I found the commit in gcc-4.8 that replaced the powerpc-specific
implementation of __builtin_bswap16 with an architecture-independent
one. Apparently the powerpc version (gcc-4.6 and 4.7) just mapped to
the lhbrx/sthbrx instructions, so it ended up not being a constant,
though the intent of the patch was mainly to add support for the
builtin to x86:
David S. Miller [Mon, 9 May 2016 18:26:14 +0000 (14:26 -0400)]
Merge branch 'dsa-mv88e6xxx-monolithic'
Vivien Didelot says:
====================
net: dsa: mv88e6xxx: turn into monolithic driver
This patchset merges all mv88e6* drivers supported by the shared
mv88e6xxx code into a single mv88e6xxx DSA switch driver.
Some flags are added to describe the capabilities of a switch model,
such as the presence of a PPU, EEPROM, some old or new registers, etc.
First these flags are used to conditionally support the same set of
functions in every driver, then specific driver files are removed in
favor of the common mv88e6xxx driver.
Only the merge of driver specific setup code assumes a few differences.
If these differences such as frames priorities are really needed for
some models, they can easily be brought back in a future patch.
Some inconsistencies might show up, such as the need for
MV88E6XXX_FLAG_PPU and MV88E6XXX_FLAG_PPU_ACTIVE flags. But this
patchset does not aim to fix them yet. A future patch can do that if
they end up being unwanted.
The patchset has been tested on interconnected 88E6352 and 88E6185.
Changes v1 -> v2:
- add missing MV88E6XXX_FLAG_EEPROM flag checks
- remove a few remaining _ prefixes
- remove MV88E6XXX_FLAG_CORE_TAG_TYPE which is a specific default
Changes RFC -> v1:
- introduce flags in a separate patch
- do not refactor anything yet
- do not add new functions prefixed with _
- drop packet discarding and mentioned tested platforms
- factorize family flags
- update text for NET_DSA_MV88E6XXX Kconfig entry
====================
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Mon, 9 May 2016 17:22:58 +0000 (13:22 -0400)]
net: dsa: mv88e6xxx: factorize the switch driver
Now that all drivers support the same set of functions and the same
setup code, drop every model-specific DSA switch driver and replace them
with a common mv88e6xxx driver.
This merges the info tables into one, removes the function exports, the
model-specific files, and update the defconfigs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Mon, 9 May 2016 17:22:57 +0000 (13:22 -0400)]
net: dsa: mv88e6131: use EDSA tag protocol
6131 is the only driver to set the tag protocol to DSA_TAG_PROTO_DSA.
Since it works fine with DSA_TAG_PROTO_EDSA, change its value, like all
other mv88e6xxx drivers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Mon, 9 May 2016 17:22:55 +0000 (13:22 -0400)]
net: dsa: mv88e6131: drop frames priorities setup
6131 is the only driver which setups the priority of IGMP/MLD snoop
frames and ARP frames to the highest setting. Drop such change until we
figure out a common configuration for all switch models.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
All switch models configure the GLOBAL_CONTROL register with slightly
differences.
Discarding packets with excessive collisions
(GLOBAL_CONTROL_DISCARD_EXCESS) is specific to 6352 and similar
switches, and setting a maximum frame size
(GLOBAL_CONTROL_MAX_FRAME_1632) is specific to 6185 and similar
switches.
As we are centralizing the chips setup, skip these settings and don't
discard any frames yet, until we found out that such discarding by the
hardware is necessary.
Assume a common setup to enable the PHY Polling Unit if present, don't
discard any packets, and mask all interrupt sources.
Vivien Didelot [Mon, 9 May 2016 17:22:44 +0000 (13:22 -0400)]
net: dsa: mv88e6xxx: factorize EEE access
Add a MV88E6XXX_FLAG_EEE flag to describe switch models featuring Energy
Efficient Ethernet. Use it to conditionally support such access in the
common code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Mon, 9 May 2016 17:22:43 +0000 (13:22 -0400)]
net: dsa: mv88e6xxx: factorize MAC address setting
Some switch models have a dedicated register for Switch MAC/WoF/WoL.
This register, when present, is used to indirectly set the switch MAC
address, instead of a direct write to 3 global registers.
Identify this feature and share a common mv88e6xxx_set_addr function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Mon, 9 May 2016 17:22:42 +0000 (13:22 -0400)]
net: dsa: mv88e6xxx: factorize temperature access
Add MV88E6XXX_FLAG_TEMP and MV88E6XXX_FLAG_TEMP_LIMIT flags to describe
switch models featuring a temperature access. Use them to centralize the
access to the temperature feature.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Mon, 9 May 2016 17:22:39 +0000 (13:22 -0400)]
net: dsa: mv88e6xxx: factorize PHY access with PPU
Add a MV88E6XXX_FLAG_PPU flag to describe switch models with a PHY
Polling Unit. This allows to merge PPU specific PHY access code in the
share code.
Make the mv88e6xxx_ppu_disable and mv88e6xxx_phy_{read,write}_ppu
functions use unlocked register accesses in order to call them in
mv88e6xxx_phy_{read,write} in a locked context.
Since the PPU code is shared, also remove NET_DSA_MV88E6XXX_NEED_PPU.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-kernels.git / log