Philippe Guibert [Thu, 11 Oct 2018 16:37:01 +0000 (18:37 +0200)]
bgpd: allow vrf validity and bgp vrf import/export, when zebra is off
if zebra is not started, then vrf identifiers are not available. This
prevents import/exportation to be available. This commit permits having
import/export available, even when zebra is not started.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Don Slice [Thu, 8 Nov 2018 19:47:27 +0000 (19:47 +0000)]
staticd: install static routes in a vrf when next-hop interface comes up
Problem reported with cross-vrf static routes that the routes weren't
installed when the target interface is bounced. Determined that we did
not initiate re-install of the statics in that particular case, so added
it. Test case previously failing now passes.
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
Mitch Skiba [Wed, 9 May 2018 23:10:02 +0000 (23:10 +0000)]
bgpd: Re-use TX Addpath IDs where possible
The motivation for this patch is to address a concerning behavior of
tx-addpath-bestpath-per-AS. Prior to this patch, all paths' TX ID was
pre-determined as the path was received from a peer. However, this meant
that any time the path selected as best from an AS changed, bgpd had no
choice but to withdraw the previous best path, and advertise the new
best-path under a new TX ID. This could cause significant network
disruption, especially for the subset of prefixes coming from only one
AS that were also communicated over a bestpath-per-AS session.
The patch's general approach is best illustrated by
txaddpath_update_ids. After a bestpath run (required for best-per-AS to
know what will and will not be sent as addpaths) ID numbers will be
stripped from paths that no longer need to be sent, and held in a pool.
Then, paths that will be sent as addpaths and do not already have ID
numbers will allocate new ID numbers, pulling first from that pool.
Finally, anything left in the pool will be returned to the allocator.
In order for this to work, ID numbers had to be split by strategy. The
tx-addpath-All strategy would keep every ID number "in use" constantly,
preventing IDs from being transferred to different paths. Rather than
create two variables for ID, this patch create a more generic array that
will easily enable more addpath strategies to be implemented. The
previously described ID manipulations will happen per addpath strategy,
and will only be run for strategies that are enabled on at least one
peer.
Finally, the ID numbers are allocated from an allocator that tracks per
AFI/SAFI/Addpath Strategy which IDs are in use. Though it would be very
improbable, there was the possibility with the free-running counter
approach for rollover to cause two paths on the same prefix to get
assigned the same TX ID. As remote as the possibility is, we prefer to
not leave it to chance.
This ID re-use method is not perfect. In some cases you could still get
withdraw-then-add behaviors where not strictly necessary. In the case of
bestpath-per-AS this requires one AS to advertise a prefix for the first
time, then a second AS withdraws that prefix, all within the space of an
already pending MRAI timer. In those situations a withdraw-then-add is
more forgivable, and fixing it would probably require a much more
significant effort, as IDs would need to be moved to ADVs instead of
paths.
Mitch Skiba [Thu, 17 May 2018 19:06:08 +0000 (19:06 +0000)]
lib: Implement an allocator for 32 bit ID numbers
This commit introduces lib/id_alloc, which has facilities for both an ID number
allocator, and less efficient ID holding pools. The pools are meant to be a
temporary holding area for ID numbers meant to be re-used, and are implemented
as a linked-list stack.
The allocator itself is much more efficient with memory. Based on sizeof
values on my 64 bit desktop, the allocator requires around 155 KiB per
million IDs tracked.
IDs are ultimately tracked in a bit-map split into many "pages." The
allocator tracks a list of pages that have free bits, and which sections
of each page have free IDs, so there isn't any scanning required to find
a free ID. (The library utility ffs, or "Find First Set," is generally a
single CPU instruction.) At the moment, totally empty pages will not be
freed, so the memory utilization of this allocator will remain at the
high water mark.
The initial intended use case is for BGP's TX Addpath IDs to be pulled
from an allocator that tracks which IDs are in use, rather than a free
running counter. The allocator reserves ID #0 as a sentinel value for
an invalid ID numbers, and BGP will want ID #1 reserved as well. To
support this, the allocator allows for IDs to be explicitly reserved,
though be aware this is only practical to use with low numbered IDs
because the allocator must allocate pages in order.
Rafael Zalamena [Sat, 3 Nov 2018 22:08:33 +0000 (19:08 -0300)]
bfdd: fix BGP unnumbered peer setup
The session key uses the scope id to figure out which interface we are
using with that link-local address, so if we don't set it when
registering a session we'll end up with multiple IPv6 sessions.
Olivier Dugeon [Fri, 26 Oct 2018 17:12:41 +0000 (19:12 +0200)]
OSPF: Add support to multi-area to Router Info.
Router Information needs to specify the area ID when flooding scope is set to
AREA. However, this authorize only one AREA. Thus, Area Border Router (ABR) are
unable to flood Router Information Opaque LSA in all areas they are belongs to.
The path implies that the area ID is no more necessary for the command
'router-info area'. It remains suported for compatibility, but mark as
deprecated. Documentation has been updated accordingly.
Donald Sharp [Tue, 6 Nov 2018 20:55:36 +0000 (15:55 -0500)]
bgpd: Late registration of Extended Nexthop should allow RA's to happen
When we have a late registration of the Extended Nexthop capability
for BGP and the peer already has nexthop information stored, go
through and enable RA on the important interfaces.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
watchfrr: Echo statements are blocking the execution of frr script
1) Certain echo statements present in the script before/after SSD process
restart are causing the FRR script to hang. This is breaking the frr script
functionality for start/stop/restart. Removed such echo statements.
Tests:
1. Multiple start, stop, restart
2. Multiple restarts/kill of same process.
Signed-off-by: Sri Mohana Singamsetty <msingamsetty@vmware.com>
Renato Westphal [Sat, 3 Nov 2018 17:27:33 +0000 (15:27 -0200)]
doc: update libyang build instructions
The --with-yangmodelsdir and --with-libyang-pluginsdir build-time options
pertain to FRR so they shouldn't be placed along with the libyang build
instructions. Move these instructions to where they belong to avoid
confusion.
Donald Sharp [Tue, 30 Oct 2018 19:12:07 +0000 (15:12 -0400)]
pimd: Send 1 on all systems for MRT_INIT
When sending a sockoption for MRT_INIT, *bsd requires that
the data passed in must be 1. While linux does not, the
code was sending in a positive value that was causing issues
on *bsd of protocol not supported.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
projects / mirror_frr.git / log