Andrew Lunn [Wed, 9 Aug 2017 16:56:13 +0000 (11:56 -0500)]
eigrpd: Add missing install_element for debug eigrp transmit
debug eigrp transmit command is added to the ENABLE_NODE list, but not
CONFIG_NODE. As a result the command cannot be used in the
configuration file. Add the missing call.
David Lamparter [Wed, 9 Aug 2017 10:37:45 +0000 (12:37 +0200)]
zebra: fix pseudowire code re. upstream changes
- VTY_NEWLINE is out
- thread API changed with the extra arg
- struct rib got renamed to struct route_entry
- MPLS_NO_LABEL was removed
- RB-tree implementation has some extra args
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
In some scenarios, it's possible to send a Label Withdraw to a neighbor
and not receive a corresponding Label Release right away. This can happen
during reconvergence after a network failure or configuration change.
When this happens, the list of upstream mappings of a given FEC might
not be empty even after sending a Label Withdraw to all neighbors. This
situation holds until all neighbors either send a Label Release or are
torn down (e.g. keepalive timeout).
With that said, we shouldn't check for 'RB_EMPTY(&fn->upstream)'
in lde_kernel_update() because it can prevent ldpd from sending label
mappings in such circumstances. This check was introduced to avoid sending
the same label mapping more than once to the same neighbor, but we need
to remove this optimization for now until we find a better solution (which
probably involves refactoring the whole zebra<->ldpd communication).
While here, add a new debug message in lde_send_labelmapping() which
can aid in troubleshooting label problems in the future.
Renato Westphal [Fri, 30 Jun 2017 15:19:39 +0000 (12:19 -0300)]
ldpd: integrate with the pseudowire manager in zebra
If we receive a notification from zebra indicating that the installation
of a pseudowire has failed (e.g. no reachability), send a PW Status
notification to the remote peer (or a Label Withdraw if the remote peer
doesn't support the PW Status TLV).
Renato Westphal [Thu, 8 Jun 2017 23:29:12 +0000 (20:29 -0300)]
zebra: add new flag to detect nexthop label updates
With the introduction of the pseudowire manager, the NHT tracking code
needs to detect label updates as well.
Create a specific nexthop flag for that. We can't reuse the
RIB_ENTRY_NEXTHOPS_CHANGED flag for this porpose because this flag is
always cleared and reevaluated in rib_process(), setting it outside that
function is a nop.
Renato Westphal [Fri, 30 Jun 2017 15:26:04 +0000 (12:26 -0300)]
zebra: add nexthop tracking for pseudowires
If the remote end of a pseudowire becomes unreachable (no route or an
unlabeled route), then it must be uninstalled. In the same way, when
the remote end becomes reachable, the pseudowire must be installed.
ßingen [Mon, 15 May 2017 15:09:28 +0000 (17:09 +0200)]
zebra: add pseudowire manager
Base framework for supporting MPLS pseudowires in FRR.
A consistent zserv interface is provided so that any client daemon
(e.g. ldpd, bgpd) can install/uninstall pseudowires in a standard
way. Static pseudowires can also be implemented by using the same
interface.
When zebra receives a request to install a pseudowire and the installation
in the kernel or hardware fails, a notification is sent back to the
client daemon and a new install attempt is made every 60 seconds (until
it succeeds).
Support for external dataplanes is provided by the use of hooks to
install/uninstall pseudowires.
ßingen [Tue, 1 Aug 2017 09:38:19 +0000 (11:38 +0200)]
ospf: Fix segfault if compiled with DEBUG
If OSPF_LS_REFRESH_TIME is 60, min_delay in ospf_refresher_register_lsa
function (ospf_lsa.c) would be negative, so index (which is unsigned)
would be out of range, causing a segfault.
We were assuming that a neighbor can be deleted only when all of its
adjacencies are dead. This is not the case for dual-stack neighbors. If
the transport-preference is IPv4 and all adjacencies are IPv6 (or
vice-versa), then it should be deleted and everything cleaned-up
accordingly.
Bug exposed by the new RB tree implementation on master, but the fix
also applies to stable/3.0.
OpenBSD uses ioctl to fetch interface information on startup and the
SIOCGIFMEDIA command is just too cumbersome to use.
The best way to fix the problem for OpenBSD is probably to stop treating
it differently from the other BSDs for no apparent reason. There should
be nothing preventing us to make OpenBSD use the routing socket to fetch
interface information on startup (we already do it to detect runtime
changes). This is something that should be done in a separate commit
after a careful analysis.
David Lamparter [Sun, 6 Aug 2017 05:35:50 +0000 (07:35 +0200)]
*: remove --enable-tcp-zebra, rework ZAPI path
This adds "@tcp" as new choice on the -z option present in zebra and the
protocol daemons. The --enable-tcp-zebra option on configure is no
longer needed, both UNIX and TCP socket support is always available.
Note that @tcp should not be used by default (e.g. in an init script),
and --enable-tcp-zebra should never have been in any distro package
builds, because
**** TCP-ZEBRA IS A SECURITY PROBLEM ****
It allows arbitrary local users to mess with the routing table and
inject bogus data -- and also ZAPI is not designed to be robust against
attacks.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Brian Rak [Mon, 7 Aug 2017 18:37:21 +0000 (14:37 -0400)]
rhel: Don't obsolete bird
The FRR RPM was obsoleting BIRD, which meant that as soon as you added a FRR RPM to a repository, you could no longer install BIRD. This patch switches it over to Conflicts instead, which should be much nicer behavior
David Lamparter [Mon, 7 Aug 2017 13:05:34 +0000 (15:05 +0200)]
lib: cli: don't run off graph "pre-end"
Behind END_TKN, there is another graph node whose data pointer is
actually struct cmd_element instead of struct cmd_token. Don't try to
interpret that as cmd_token. This causes very interesting crashes when
ASLR decides to give one of the strings of a command definition a lower
32-bit value that is a valid cmd_token_type (e.g. FORK_TKN).
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
David Lamparter [Sun, 6 Aug 2017 03:14:39 +0000 (05:14 +0200)]
zebra: static: update on ifindex changes
Whenever an interface is created or deleted in the system, we need to
check whether we have static routes referencing that interface by name.
If so, we need to [un]install these routes.
This has the unfortunate side effect of making static routes with
non-existent interfaces disappear from "show ip route", but I think
that's acceptable (and I don't see a "good" fix for that).
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
David Lamparter [Sun, 6 Aug 2017 03:14:39 +0000 (05:14 +0200)]
zebra: static: update on ifindex changes
Whenever an interface is created or deleted in the system, we need to
check whether we have static routes referencing that interface by name.
If so, we need to [un]install these routes.
This has the unfortunate side effect of making static routes with
non-existent interfaces disappear from "show ip route", but I think
that's acceptable (and I don't see a "good" fix for that).
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Jorge Boncompte [Fri, 4 Aug 2017 17:33:15 +0000 (19:33 +0200)]
bgpd: remove bogus change in attrhash_key_make()
Commit c8e7b895 ("bgpd: use Jenkins hash for BGP transit, cluster and
attr hashes") changed attrhash_key_make() to use Jenkins hash, commit c8f3fe30 ("bgpd: Remove AS Path limit/TTL functionality") introduced
a bogus change with a snippet of code that was deleted in the first
one.
Chirag Shah [Thu, 3 Aug 2017 23:34:17 +0000 (16:34 -0700)]
ospfd: Fix MI-OSPF configuraton clis
Multi-Instance OSPF configuration CLI would fail because
first client return error upon seeing qobj_index being 0.
With new marco generate new error code to return from each
instance (vtysh client) and if the command is intended for given
instance, its qobj_index would be nonzero and process the command
and push correct ospf context. Other instance would return the error.
On vtysh end, check all instance return an error log a message to a
file.
Testing Done:
Verfied various MI-OSPF configuration CLI with multi instances.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
isisd: don't validate dict integrity for regular builds
This method is intended to be only used for debugging as per the author
and profiling shows we are spending a lot of cycles on it. Remove it for
regular builds by guarding it with a define.
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Donald Sharp [Thu, 3 Aug 2017 12:42:29 +0000 (08:42 -0400)]
lib: Add ETH_ALEN to prefix.h and deprecate ETHER_ADDR_LEN
From discussion we decided that we should use ETH_ALEN instead
of ETHER_ADDR_LEN. Add ETH_ALEN to prefix.h and make
ETHER_ADDR_LEN generate a warning when used( but still work ).
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Donald Sharp [Thu, 3 Aug 2017 11:43:47 +0000 (07:43 -0400)]
zebra: Fix crash when OOM happens.
The hash key function choosen for mac vni's would tend
to clump the key value to the same number. Use a better
hash key generator to spread the hash values out.
A bad hash key might lead to O(2^n) memory consumption
because the hash size is doubled, each time a backet
exceeds a predefined threshold. This quickly leads
to OOM. Fixing this issue by fixing the hash
key generation to actually spread the keys out.
Ticket: CM-17412 Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
David Lamparter [Fri, 4 Aug 2017 08:36:34 +0000 (10:36 +0200)]
build: clean up BUILT_SOURCES
BUILT_SOURCES doesn't do what the name suggests. What it actually means
is "these files should be built first when doing a 'make' without
explicit target" (or "make all").
It's pretty much almost always wrong to use BUILT_SOURCES, the only
correct use is when a file is needed by an unspecified / large set of
files.
Also remove version.h and route_types.h from dist tarball while we're at
it. configure will create them anyway.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
David Lamparter [Fri, 4 Aug 2017 07:59:00 +0000 (09:59 +0200)]
build: pre-generate built headers in configure
zebra.h includes route_types.h, which means almost all of our Makefile
targets have a dependency on route_types.h. While BUILT_SOURCES ensures
that this dependency is fulfilled on a "make all", this doesn't work
when building specific targets (e.g. "make lib/libfrr.la").
There seems to be no good way to add a dependency on everything, so the
best fix for this is to just generate the file during ./configure.
(The Makefile rule is still there, so if route_types.txt is changed,
route_types.h will be rebuilt.)
This only affects "initial" builds from a clean directory and/or builds
with --disable-dependency-tracking; other than that gcc will output
Makefile dependencies during compilation so that route_types.h will
become a dependency for all output files.
gitversion.h has the same problem on a smaller scope.
command_lex.h & command_parse.h *don't* have the problem because they're
only used in specific files, and these files have the dependency
explicitly listed in the Makefile. Hence, they can also be removed from
BUILT_SOURCES.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
projects / mirror_frr.git / log