[mirror_ubuntu-artful-kernel.git] / drivers / scsi / mesh.h

/*
 * mesh.h: definitions for the driver for the MESH SCSI bus adaptor
 * (Macintosh Enhanced SCSI Hardware) found on Power Macintosh computers.
 *
 * Copyright (C) 1996 Paul Mackerras.
 */
#ifndef _MESH_H
#define _MESH_H

/*
 * Registers in the MESH controller.
 */

struct mesh_regs {
	unsigned char	count_lo;
	char pad0[15];
	unsigned char	count_hi;
	char pad1[15];
	unsigned char	fifo;
	char pad2[15];
	unsigned char	sequence;
	char pad3[15];
	unsigned char	bus_status0;
	char pad4[15];
	unsigned char	bus_status1;
	char pad5[15];
	unsigned char	fifo_count;
	char pad6[15];
	unsigned char	exception;
	char pad7[15];
	unsigned char	error;
	char pad8[15];
	unsigned char	intr_mask;
	char pad9[15];
	unsigned char	interrupt;
	char pad10[15];
	unsigned char	source_id;
	char pad11[15];
	unsigned char	dest_id;
	char pad12[15];
	unsigned char	sync_params;
	char pad13[15];
	unsigned char	mesh_id;
	char pad14[15];
	unsigned char	sel_timeout;
	char pad15[15];
};

/* Bits in the sequence register. */
#define SEQ_DMA_MODE	0x80	/* use DMA for data transfer */
#define SEQ_TARGET	0x40	/* put the controller into target mode */
#define SEQ_ATN		0x20	/* assert ATN signal */
#define SEQ_ACTIVE_NEG	0x10	/* use active negation on REQ/ACK */
#define SEQ_CMD		0x0f	/* command bits: */
#define SEQ_ARBITRATE	1	/*  get the bus */
#define SEQ_SELECT	2	/*  select a target */
#define SEQ_COMMAND	3	/*  send a command */
#define SEQ_STATUS	4	/*  receive status */
#define SEQ_DATAOUT	5	/*  send data */
#define SEQ_DATAIN	6	/*  receive data */
#define SEQ_MSGOUT	7	/*  send a message */
#define SEQ_MSGIN	8	/*  receive a message */
#define SEQ_BUSFREE	9	/*  look for bus free */
#define SEQ_ENBPARITY	0x0a	/*  enable parity checking */
#define SEQ_DISPARITY	0x0b	/*  disable parity checking */
#define SEQ_ENBRESEL	0x0c	/*  enable reselection */
#define SEQ_DISRESEL	0x0d	/*  disable reselection */
#define SEQ_RESETMESH	0x0e	/*  reset the controller */
#define SEQ_FLUSHFIFO	0x0f	/*  clear out the FIFO */

/* Bits in the bus_status0 and bus_status1 registers:
   these correspond directly to the SCSI bus control signals. */
#define BS0_REQ		0x20
#define BS0_ACK		0x10
#define BS0_ATN		0x08
#define BS0_MSG		0x04
#define BS0_CD		0x02
#define BS0_IO		0x01
#define BS1_RST		0x80
#define BS1_BSY		0x40
#define BS1_SEL		0x20

/* Bus phases defined by the bits in bus_status0 */
#define BS0_PHASE	(BS0_MSG+BS0_CD+BS0_IO)
#define BP_DATAOUT	0
#define BP_DATAIN	BS0_IO
#define BP_COMMAND	BS0_CD
#define BP_STATUS	(BS0_CD+BS0_IO)
#define BP_MSGOUT	(BS0_MSG+BS0_CD)
#define BP_MSGIN	(BS0_MSG+BS0_CD+BS0_IO)

/* Bits in the exception register. */
#define EXC_SELWATN	0x20	/* (as target) we were selected with ATN */
#define EXC_SELECTED	0x10	/* (as target) we were selected w/o ATN */
#define EXC_RESELECTED	0x08	/* (as initiator) we were reselected */
#define EXC_ARBLOST	0x04	/* we lost arbitration */
#define EXC_PHASEMM	0x02	/* SCSI phase mismatch */
#define EXC_SELTO	0x01	/* selection timeout */

/* Bits in the error register */
#define ERR_UNEXPDISC	0x40	/* target unexpectedly disconnected */
#define ERR_SCSIRESET	0x20	/* SCSI bus got reset on us */
#define ERR_SEQERR	0x10	/* we did something the chip didn't like */
#define ERR_PARITY	0x01	/* parity error was detected */

/* Bits in the interrupt and intr_mask registers */
#define INT_ERROR	0x04	/* error interrupt */
#define INT_EXCEPTION	0x02	/* exception interrupt */
#define INT_CMDDONE	0x01	/* command done interrupt */

/* Fields in the sync_params register */
#define SYNC_OFF(x)	((x) >> 4)	/* offset field */
#define SYNC_PER(x)	((x) & 0xf)	/* period field */
#define SYNC_PARAMS(o, p)	(((o) << 4) | (p))
#define ASYNC_PARAMS	2	/* sync_params value for async xfers */

/*
 * Assuming a clock frequency of 50MHz:
 *
 * The transfer period with SYNC_PER(sync_params) == x
 * is (x + 2) * 40ns, except that x == 0 gives 100ns.
 *
 * The units of the sel_timeout register are 10ms.
 */


#endif /* _MESH_H */
Commit	Line	Data
1da177e4 LT	1	/*
	2	* mesh.h: definitions for the driver for the MESH SCSI bus adaptor
	3	* (Macintosh Enhanced SCSI Hardware) found on Power Macintosh computers.
	4	*
	5	* Copyright (C) 1996 Paul Mackerras.
	6	*/
	7	#ifndef _MESH_H
	8	#define _MESH_H
	9
	10	/*
	11	* Registers in the MESH controller.
	12	*/
	13
	14	struct mesh_regs {
	15	unsigned char count_lo;
	16	char pad0[15];
	17	unsigned char count_hi;
	18	char pad1[15];
	19	unsigned char fifo;
	20	char pad2[15];
	21	unsigned char sequence;
	22	char pad3[15];
	23	unsigned char bus_status0;
	24	char pad4[15];
	25	unsigned char bus_status1;
	26	char pad5[15];
	27	unsigned char fifo_count;
	28	char pad6[15];
	29	unsigned char exception;
	30	char pad7[15];
	31	unsigned char error;
	32	char pad8[15];
	33	unsigned char intr_mask;
	34	char pad9[15];
	35	unsigned char interrupt;
	36	char pad10[15];
	37	unsigned char source_id;
	38	char pad11[15];
	39	unsigned char dest_id;
	40	char pad12[15];
	41	unsigned char sync_params;
	42	char pad13[15];
	43	unsigned char mesh_id;
	44	char pad14[15];
	45	unsigned char sel_timeout;
	46	char pad15[15];
	47	};
	48
	49	/* Bits in the sequence register. */
	50	#define SEQ_DMA_MODE 0x80 /* use DMA for data transfer */
	51	#define SEQ_TARGET 0x40 /* put the controller into target mode */
	52	#define SEQ_ATN 0x20 /* assert ATN signal */
	53	#define SEQ_ACTIVE_NEG 0x10 /* use active negation on REQ/ACK */
	54	#define SEQ_CMD 0x0f /* command bits: */
	55	#define SEQ_ARBITRATE 1 /* get the bus */
	56	#define SEQ_SELECT 2 /* select a target */
	57	#define SEQ_COMMAND 3 /* send a command */
	58	#define SEQ_STATUS 4 /* receive status */
	59	#define SEQ_DATAOUT 5 /* send data */
	60	#define SEQ_DATAIN 6 /* receive data */
	61	#define SEQ_MSGOUT 7 /* send a message */
	62	#define SEQ_MSGIN 8 /* receive a message */
	63	#define SEQ_BUSFREE 9 /* look for bus free */
	64	#define SEQ_ENBPARITY 0x0a /* enable parity checking */
65	#define SEQ_DISPARITY 0x0b /* disable parity checking */
66	#define SEQ_ENBRESEL 0x0c /* enable reselection */
67	#define SEQ_DISRESEL 0x0d /* disable reselection */
68	#define SEQ_RESETMESH 0x0e /* reset the controller */
69	#define SEQ_FLUSHFIFO 0x0f /* clear out the FIFO */
70
71	/* Bits in the bus_status0 and bus_status1 registers:
72	these correspond directly to the SCSI bus control signals. */
73	#define BS0_REQ 0x20
74	#define BS0_ACK 0x10
75	#define BS0_ATN 0x08
76	#define BS0_MSG 0x04
77	#define BS0_CD 0x02
78	#define BS0_IO 0x01
79	#define BS1_RST 0x80
80	#define BS1_BSY 0x40
81	#define BS1_SEL 0x20
82
83	/* Bus phases defined by the bits in bus_status0 */
84	#define BS0_PHASE (BS0_MSG+BS0_CD+BS0_IO)
85	#define BP_DATAOUT 0
86	#define BP_DATAIN BS0_IO
87	#define BP_COMMAND BS0_CD
88	#define BP_STATUS (BS0_CD+BS0_IO)
89	#define BP_MSGOUT (BS0_MSG+BS0_CD)
90	#define BP_MSGIN (BS0_MSG+BS0_CD+BS0_IO)
91
92	/* Bits in the exception register. */
93	#define EXC_SELWATN 0x20 /* (as target) we were selected with ATN */
94	#define EXC_SELECTED 0x10 /* (as target) we were selected w/o ATN */
95	#define EXC_RESELECTED 0x08 /* (as initiator) we were reselected */
96	#define EXC_ARBLOST 0x04 /* we lost arbitration */
97	#define EXC_PHASEMM 0x02 /* SCSI phase mismatch */
98	#define EXC_SELTO 0x01 /* selection timeout */
99
100	/* Bits in the error register */
101	#define ERR_UNEXPDISC 0x40 /* target unexpectedly disconnected */
102	#define ERR_SCSIRESET 0x20 /* SCSI bus got reset on us */
103	#define ERR_SEQERR 0x10 /* we did something the chip didn't like */
104	#define ERR_PARITY 0x01 /* parity error was detected */
105
106	/* Bits in the interrupt and intr_mask registers */
107	#define INT_ERROR 0x04 /* error interrupt */
108	#define INT_EXCEPTION 0x02 /* exception interrupt */
109	#define INT_CMDDONE 0x01 /* command done interrupt */
110
111	/* Fields in the sync_params register */
112	#define SYNC_OFF(x) ((x) >> 4) /* offset field */
113	#define SYNC_PER(x) ((x) & 0xf) /* period field */
114	#define SYNC_PARAMS(o, p) (((o) << 4) \| (p))
115	#define ASYNC_PARAMS 2 /* sync_params value for async xfers */
116
117	/*
118	* Assuming a clock frequency of 50MHz:
119	*
120	* The transfer period with SYNC_PER(sync_params) == x
121	* is (x + 2) * 40ns, except that x == 0 gives 100ns.
122	*
123	* The units of the sel_timeout register are 10ms.
124	*/
125
126
127	#endif /* _MESH_H */