{
int result;
int channel = 0;
- dev_dbg(&xr_usb_serial->control->dev, "%s Channel:%d 0x%02x = 0x%02x\n", __func__,channel,regnum, value);
+ //dev_info(&xr_usb_serial->control->dev, "%s Channel:%d 0x%02x = 0x%02x\n", __func__,channel,regnum, value);
if((xr_usb_serial->DeviceProduct&0xfff0) == 0x1400)
{
int XR2280xaddr = XR2280x_FUNC_MGR_OFFSET + regnum;
result = -1;
}
if(result < 0)
- dev_dbg(&xr_usb_serial->control->dev, "%s Error:%d\n", __func__,result);
+ dev_err(&xr_usb_serial->control->dev, "%s Error:%d\n", __func__,result);
return result;
{
int result;
int XR2280xaddr = XR2280x_FUNC_MGR_OFFSET + regnum;
- dev_dbg(&xr_usb_serial->control->dev, "%s channel:%d 0x%02x = 0x%02x\n", __func__,channel,regnum, value);
+ //dev_info(&xr_usb_serial->control->dev, "%s channel:%d 0x%02x = 0x%02x\n", __func__,channel,regnum, value);
if((xr_usb_serial->DeviceProduct&0xfff0) == 0x1400)
{
result = usb_control_msg(xr_usb_serial->dev, /* usb device */
result = -1;
}
if(result < 0)
- dev_dbg(&xr_usb_serial->control->dev, "%s Error:%d\n", __func__,result);
+ dev_err(&xr_usb_serial->control->dev, "%s Error:%d\n", __func__,result);
return result;
}
if(result < 0)
- dev_dbg(&xr_usb_serial->control->dev, "%s channel:%d Reg 0x%x Error:%d\n", __func__,channel,regnum,result);
- else
- dev_dbg(&xr_usb_serial->control->dev, "%s channel:%d 0x%x = 0x%04x\n", __func__,channel,regnum, *value);
+ dev_err(&xr_usb_serial->control->dev, "%s channel:%d Reg 0x%x Error:%d\n", __func__,channel,regnum,result);
+ //else
+ //dev_info(&xr_usb_serial->control->dev, "%s channel:%d 0x%x = 0x%04x\n", __func__,channel,regnum, *value);
return result;
®_value, /* data */
1, /* size */
5000); /* timeout */
- dev_dbg(&xr_usb_serial->control->dev, "xr_usb_serial_get_reg_ext reg:%x\n",reg_value);
+ //dev_dbg(&xr_usb_serial->control->dev, "xr_usb_serial_get_reg_ext reg:%x\n",reg_value);
*value = reg_value;
}
else if(xr_usb_serial->DeviceProduct == 0x1411)
}
if(result < 0)
- dev_dbg(&xr_usb_serial->control->dev, "%s Error:%d\n", __func__,result);
- else
- dev_dbg(&xr_usb_serial->control->dev, "%s channel:%d 0x%x = 0x%04x\n", __func__,channel,regnum, *value);
+ dev_err(&xr_usb_serial->control->dev, "%s Error:%d\n", __func__,result);
+ //else
+ //dev_info(&xr_usb_serial->control->dev, "%s channel:%d 0x%x = 0x%04x\n", __func__,channel,regnum, *value);
return result;
unsigned int tx_mask = xr21v141x_baud_rates[i].tx;
unsigned int rx_mask = (divisor & 1) ? xr21v141x_baud_rates[i].rx1 : xr21v141x_baud_rates[i].rx0;
- dev_dbg(&xr_usb_serial->control->dev, "Setting baud rate to %d: i=%u div=%u tx=%03x rx=%03x\n", rate, i, divisor, tx_mask, rx_mask);
+ //dev_info(&xr_usb_serial->control->dev, "Setting baud rate to %d: i=%u div=%u tx=%03x rx=%03x\n", rate, i, divisor, tx_mask, rx_mask);
xr_usb_serial_set_reg(xr_usb_serial,UART_CLOCK_DIVISOR_0, (divisor >> 0) & 0xff);
xr_usb_serial_set_reg(xr_usb_serial,UART_CLOCK_DIVISOR_1, (divisor >> 8) & 0xff);
if (cflag & CRTSCTS)
{
- dev_dbg(&xr_usb_serial->control->dev, "xr_usb_serial_set_flow_mode:hardware\n");
+ //dev_dbg(&xr_usb_serial->control->dev, "xr_usb_serial_set_flow_mode:hardware\n");
flow = UART_FLOW_MODE_HW;
gpio_mode = UART_GPIO_MODE_SEL_RTS_CTS;
}
{
unsigned char start_char = START_CHAR(tty);
unsigned char stop_char = STOP_CHAR(tty);
- dev_dbg(&xr_usb_serial->control->dev, "xr_usb_serial_set_flow_mode:software\n");
+ //dev_dbg(&xr_usb_serial->control->dev, "xr_usb_serial_set_flow_mode:software\n");
flow = UART_FLOW_MODE_SW;
gpio_mode = UART_GPIO_MODE_SEL_GPIO;
}
else
{
- dev_dbg(&xr_usb_serial->control->dev, "xr_usb_serial_set_flow_mode:none\n");
+ //dev_dbg(&xr_usb_serial->control->dev, "xr_usb_serial_set_flow_mode:none\n");
flow = UART_FLOW_MODE_NONE;
gpio_mode = UART_GPIO_MODE_SEL_GPIO;
}
- // rs485,rs422 FD/HD mode
- if (xr_usb_serial->rs485_422_en) {
- xr_usb_serial_set_reg(xr_usb_serial, xr_usb_serial->reg_map.uart_flow_addr, 0x00);
- xr_usb_serial_set_reg(xr_usb_serial, xr_usb_serial->reg_map.uart_gpio_mode_addr, 0x0B);
- } else {
- //rs232, default mode
- xr_usb_serial_set_reg(xr_usb_serial, xr_usb_serial->reg_map.uart_flow_addr, flow);
- xr_usb_serial_set_reg(xr_usb_serial, xr_usb_serial->reg_map.uart_gpio_mode_addr, gpio_mode);
+
+ if((xr_usb_serial->DeviceProduct == 0x1420)||
+ (xr_usb_serial->DeviceProduct == 0x1422)||
+ (xr_usb_serial->DeviceProduct == 0x1424))
+ {//Add support for the TXT and RXT function for 0x1420, 0x1422, 0x1424, by setting GPIO_MODE [9:8] = '11'
+ gpio_mode |= 0x300;
+ }
+
+ if((xr_usb_serial->DeviceProduct == 0x1412)||
+ (xr_usb_serial->DeviceProduct == 0x1414))
+ {
+ if(xr_usb_serial->found_smbios_exar_config)
+ {
+ if((xr_usb_serial->channel_config == 2)
+ ||(xr_usb_serial->channel_config == 3))
+ //if find the exar channel config in the smbios, the value can not be changed by the application
+ //dev_info(&xr_usb_serial->control->dev, "Sorry, Application can not change the channel gpio&flow mode,because there are config at SMBIOS\n");
+ return 0;
+ }
+ }
+
+ xr_usb_serial_set_reg(xr_usb_serial, xr_usb_serial->reg_map.uart_flow_addr, flow);
+
+ if((xr_usb_serial->found_smbios_exar_config == 1)&&(xr_usb_serial->channel_config == 1))
+ {
+ //dev_info(&xr_usb_serial->control->dev, "Sorry, Application can not change the channel gpio mode,because there are config at SMBIOS\n");
}
+ else
+ xr_usb_serial_set_reg(xr_usb_serial, xr_usb_serial->reg_map.uart_gpio_mode_addr, gpio_mode);
+
return 0;
}
+
+
+
int xr_usb_serial_send_break(struct xr_usb_serial *xr_usb_serial, int state)
{
#define URM_ENABLE_BASE 0x010
#define URM_ENABLE_0_TX 0x001
#define URM_ENABLE_0_RX 0x002
+#define URM_RESET_RX_FIFO_BASE 0x018
+#define URM_RESET_TX_FIFO_BASE 0x01C
+
+
int xr_usb_serial_enable(struct xr_usb_serial *xr_usb_serial)
{
int ret = 0;
int channel = xr_usb_serial->channel;
+ //dev_info(&xr_usb_serial->control->dev, "xr_usb_serial_enable channel=%d\n",channel);
+ if(channel) channel--;
if((xr_usb_serial->DeviceProduct == 0x1410)||
(xr_usb_serial->DeviceProduct == 0x1412)||
(xr_usb_serial->DeviceProduct == 0x1414))
return ret;
}
+int xr_usb_serial_fifo_reset(struct xr_usb_serial *xr_usb_serial)
+{
+ int ret = 0;
+ int channel = xr_usb_serial->channel;
+
+ if(channel) channel--;
+ if((xr_usb_serial->DeviceProduct == 0x1410)||
+ (xr_usb_serial->DeviceProduct == 0x1412)||
+ (xr_usb_serial->DeviceProduct == 0x1414))
+ {
+
+ ret = xr_usb_serial_set_reg_ext(xr_usb_serial,URM_REG_BLOCK,URM_RESET_RX_FIFO_BASE + channel,0xff);
+ ret |= xr_usb_serial_set_reg_ext(xr_usb_serial,URM_REG_BLOCK,URM_RESET_TX_FIFO_BASE + channel,0xff);
+
+ }
+ return ret;
+}
+
+
int xr_usb_serial_disable(struct xr_usb_serial *xr_usb_serial)
{
int ret = 0;
int channel = xr_usb_serial->channel;
+ //dev_info(&xr_usb_serial->control->dev, "xr_usb_serial_disable channel=%d\n",channel);
+ if(channel) channel--;
ret = xr_usb_serial_set_reg(xr_usb_serial,xr_usb_serial->reg_map.uart_enable_addr,0);
if((xr_usb_serial->DeviceProduct == 0x1410)||
(xr_usb_serial->DeviceProduct == 0x1412)||
{
int ret = 0;
xr_usb_serial_disable(xr_usb_serial);
- ret = xr_usb_serial_set_reg_ext(xr_usb_serial,channel,
+
+ if((xr_usb_serial->DeviceProduct == 0x1410) ||
+ (xr_usb_serial->DeviceProduct == 0x1412) ||
+ (xr_usb_serial->DeviceProduct == 0x1414))
+ {
+ switch (channel)
+ {
+ case 0:
+ ret = xr_usb_serial_set_reg_ext(xr_usb_serial,channel,
+ xr_usb_serial->reg_map.uart_loopback_addr,0x40);
+ break;
+ case 1:
+ ret = xr_usb_serial_set_reg_ext(xr_usb_serial,channel,
+ xr_usb_serial->reg_map.uart_loopback_addr,0x41);
+ break;
+ case 2:
+ ret = xr_usb_serial_set_reg_ext(xr_usb_serial,channel,
+ xr_usb_serial->reg_map.uart_loopback_addr,0x42);
+ break;
+ case 3:
+ ret = xr_usb_serial_set_reg_ext(xr_usb_serial,channel,
+ xr_usb_serial->reg_map.uart_loopback_addr,0x43);
+ break;
+ default:
+
+ break;
+ }
+ }
+ else if((xr_usb_serial->DeviceProduct == 0x1420)||
+ (xr_usb_serial->DeviceProduct == 0x1422)||
+ (xr_usb_serial->DeviceProduct == 0x1424))
+ {
+ ret = xr_usb_serial_set_reg_ext(xr_usb_serial,channel,
xr_usb_serial->reg_map.uart_loopback_addr,0x07);
+ }
xr_usb_serial_enable(xr_usb_serial);
return ret;
}
+#define XR21V1414_WIDE_MODE_OFFSET 3
+#define XR21B142X_WIDE_MODE_TX_OFFSET 0x42
+#define XR21B142X_WIDE_MODE_RX_OFFSET 0x45
+int xr_usb_serial_set_wide_mode(struct xr_usb_serial *xr_usb_serial, int preciseflags)
+{
+ int ret = 0;
+ int channel = xr_usb_serial->channel;
+ xr_usb_serial_disable(xr_usb_serial);
+ if((xr_usb_serial->DeviceProduct&0xfff0) == 0x1400)
+ {
+
+ }
+ else if((xr_usb_serial->DeviceProduct == 0x1410)||
+ (xr_usb_serial->DeviceProduct == 0x1412)||
+ (xr_usb_serial->DeviceProduct == 0x1414))
+ {
+
+ if(channel) channel--;
+ xr_usb_serial_set_reg_ext(xr_usb_serial, 0x66, channel*8 + XR21V1414_WIDE_MODE_OFFSET, preciseflags);
+
+ }
+ else if(xr_usb_serial->DeviceProduct == 0x1411)
+ {
+ xr_usb_serial_set_reg(xr_usb_serial,0xd02, preciseflags);
+ }
+ else if((xr_usb_serial->DeviceProduct == 0x1420)||
+ (xr_usb_serial->DeviceProduct == 0x1422)||
+ (xr_usb_serial->DeviceProduct == 0x1424))
+ {
+ xr_usb_serial_set_reg(xr_usb_serial, XR21B142X_WIDE_MODE_TX_OFFSET, preciseflags);
+ xr_usb_serial_set_reg(xr_usb_serial, XR21B142X_WIDE_MODE_RX_OFFSET, preciseflags);
+ }
+ xr_usb_serial_enable(xr_usb_serial);
+ return ret;
+}
+
static int xr_usb_serial_tiocmget(struct xr_usb_serial *xr_usb_serial)
short data;
int result;
result = xr_usb_serial_get_reg(xr_usb_serial,xr_usb_serial->reg_map.uart_gpio_status_addr, &data);
- dev_dbg(&xr_usb_serial->control->dev, "xr_usb_serial_tiocmget uart_gpio_status_addr:0x%04x\n",data);
+ //dev_info(&xr_usb_serial->control->dev, "xr_usb_serial_tiocmget uart_gpio_status_addr:0x%04x\n",data);
if (result)
return ((data & 0x8) ? 0: TIOCM_DTR) | ((data & 0x20) ? 0:TIOCM_RTS ) | ((data & 0x4) ? 0:TIOCM_DSR) | ((data & 0x1) ? 0 : TIOCM_RI) | ((data & 0x2) ? 0:TIOCM_CD) | ((data & 0x10) ? 0 : TIOCM_CTS);
else
xr21b140x_reg_map.uart_custom_driver = 0x60;
xr21b140x_reg_map.uart_low_latency = 0x46;
}
-
+int smbios_check_if_have_exar_config(unsigned char *config0,unsigned char *config1);
int xr_usb_serial_pre_setup(struct xr_usb_serial *xr_usb_serial)
{
int ret = 0;
-
+ unsigned char channel1_config = 255;
+ unsigned char channel2_config = 255;
init_xr21b140x_reg_map();
init_xr21b1411_reg_map();
init_xr21v141x_reg_map();
xr_usb_serial_set_reg(xr_usb_serial, xr_usb_serial->reg_map.uart_gpio_dir_addr, 0x28);
xr_usb_serial_set_reg(xr_usb_serial, xr_usb_serial->reg_map.uart_gpio_set_addr, UART_GPIO_SET_DTR | UART_GPIO_SET_RTS);
+ if((xr_usb_serial->DeviceProduct == 0x1412)||
+ (xr_usb_serial->DeviceProduct == 0x1414))
+ {
+ xr_usb_serial->found_smbios_exar_config = 0;
+ if(smbios_check_if_have_exar_config(&channel1_config,&channel2_config) == 0)
+ {
+
+ if(xr_usb_serial->channel == 1)
+ {
+ xr_usb_serial->found_smbios_exar_config = 1;
+ xr_usb_serial->channel_config = channel1_config;
+ switch (channel1_config)
+ {
+ case 1://for RS232 Mode
+ //dev_info(&xr_usb_serial->control->dev, "SMBIOS Set Channel Mode to RS232\n");
+ xr_usb_serial_set_reg(xr_usb_serial, xr_usb_serial->reg_map.uart_gpio_mode_addr, 0);
+
+ break;
+ case 2://RS-485 HALF DUPLEX
+ //dev_info(&xr_usb_serial->control->dev, "SMBIOS Set Channel Mode to RS-485 HALF DUPLEX\n");
+ xr_usb_serial_set_reg(xr_usb_serial, xr_usb_serial->reg_map.uart_gpio_mode_addr, 0x0b);
+ xr_usb_serial_set_reg(xr_usb_serial, xr_usb_serial->reg_map.uart_flow_addr, 0x00);
+ break;
+ case 3://RS-485/422 FULL DUPLEX
+ //dev_info(&xr_usb_serial->control->dev, "SMBIOS Set Channel Mode to RS-485/422 FULL DUPLEX\n");
+ xr_usb_serial_set_reg(xr_usb_serial, xr_usb_serial->reg_map.uart_gpio_mode_addr, 0x0b);
+ xr_usb_serial_set_reg(xr_usb_serial, xr_usb_serial->reg_map.uart_flow_addr, 0x00);
+ break;
+ default:
+ xr_usb_serial->found_smbios_exar_config = 0;
+ break;
+ }
+
+ }
+ else if(xr_usb_serial->channel == 2)
+ {
+ xr_usb_serial->found_smbios_exar_config = 1;
+ xr_usb_serial->channel_config = channel2_config;
+ switch (channel2_config)
+ {
+ case 1://for RS232 Mode
+ //dev_info(&xr_usb_serial->control->dev, "SMBIOS Set Channel Mode to RS232\n");
+ xr_usb_serial_set_reg(xr_usb_serial, xr_usb_serial->reg_map.uart_gpio_mode_addr, 0);
+
+ break;
+ case 2://RS-485 HALF DUPLEX
+ //dev_info(&xr_usb_serial->control->dev, "SMBIOS Set Channel Mode to RS-485 HALF DUPLEX\n");
+ xr_usb_serial_set_reg(xr_usb_serial, xr_usb_serial->reg_map.uart_gpio_mode_addr, 0x0b);
+ xr_usb_serial_set_reg(xr_usb_serial, xr_usb_serial->reg_map.uart_flow_addr, 0x00);
+ break;
+ case 3://RS-485/422 FULL DUPLEX
+ //dev_info(&xr_usb_serial->control->dev, "SMBIOS Set Channel Mode to RS-485/422 FULL DUPLEX\n");
+ xr_usb_serial_set_reg(xr_usb_serial, xr_usb_serial->reg_map.uart_gpio_mode_addr, 0x0b);
+ xr_usb_serial_set_reg(xr_usb_serial, xr_usb_serial->reg_map.uart_flow_addr, 0x00);
+ break;
+ default:
+ xr_usb_serial->found_smbios_exar_config = 0;
+ break;
+ }
+ }
+ else
+ {
+ //Nothing to do
+ }
+ }
+
+ }
return ret;
}
-
-
projects / mirror_ubuntu-bionic-kernel.git / blobdiff