]> git.proxmox.com Git - mirror_ubuntu-bionic-kernel.git/commit
clk: renesas: cpg-mssr: Fix reset control race condition
authorGeert Uytterhoeven <geert+renesas@glider.be>
Thu, 11 Jul 2019 13:03:59 +0000 (15:03 +0200)
committerKleber Sacilotto de Souza <kleber.souza@canonical.com>
Tue, 17 Sep 2019 16:02:18 +0000 (18:02 +0200)
commit7b9674fc63d00e72cba76b27a20fee755b106d24
tree75f1ca8caede0d9e070716d0bd8a0148c317cc9a
parentdb71b9cf0e89c801a2da5c30590fdf83c6133325
clk: renesas: cpg-mssr: Fix reset control race condition

BugLink: https://bugs.launchpad.net/bugs/1841652
[ Upstream commit e1f1ae8002e4b06addc52443fcd975bbf554ae92 ]

The module reset code in the Renesas CPG/MSSR driver uses
read-modify-write (RMW) operations to write to a Software Reset Register
(SRCRn), and simple writes to write to a Software Reset Clearing
Register (SRSTCLRn), as was mandated by the R-Car Gen2 and Gen3 Hardware
User's Manuals.

However, this may cause a race condition when two devices are reset in
parallel: if the reset for device A completes in the middle of the RMW
operation for device B, device A may be reset again, causing subtle
failures (e.g. i2c timeouts):

thread A thread B
-------- --------

val = SRCRn
val |= bit A
SRCRn = val

delay

val = SRCRn (bit A is set)

SRSTCLRn = bit A
(bit A in SRCRn is cleared)

val |= bit B
SRCRn = val (bit A and B are set)

This can be reproduced on e.g. Salvator-XS using:

    $ while true; do i2cdump -f -y 4 0x6A b > /dev/null; done &
    $ while true; do i2cdump -f -y 2 0x10 b > /dev/null; done &

    i2c-rcar e6510000.i2c: error -110 : 40000002
    i2c-rcar e66d8000.i2c: error -110 : 40000002

According to the R-Car Gen3 Hardware Manual Errata for Rev.
0.80 of Feb 28, 2018, reflected in Rev. 1.00 of the R-Car Gen3 Hardware
User's Manual, writes to SRCRn do not require read-modify-write cycles.

Note that the R-Car Gen2 Hardware User's Manual has not been updated
yet, and still says a read-modify-write sequence is required.  According
to the hardware team, the reset hardware block is the same on both R-Car
Gen2 and Gen3, though.

Hence fix the issue by replacing the read-modify-write operations on
SRCRn by simple writes.

Reported-by: Yao Lihua <Lihua.Yao@desay-svautomotive.com>
Fixes: 6197aa65c4905532 ("clk: renesas: cpg-mssr: Add support for reset control")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Linh Phung <linh.phung.jy@renesas.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
drivers/clk/renesas/renesas-cpg-mssr.c