Paolo Bonzini [Tue, 10 Oct 2017 10:51:56 +0000 (12:51 +0200)]
KVM: SVM: unconditionally wake up VCPU on IOMMU interrupt
Checking the mode is unnecessary, and is done without a memory barrier
separating the LAPIC write from the vcpu->mode read; in addition,
kvm_vcpu_wake_up is already doing a check for waiters on the wait queue
that has the same effect.
In practice it's safe because spin_lock has full-barrier semantics on x86,
but don't be too clever.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Wanpeng Li [Mon, 9 Oct 2017 22:51:53 +0000 (15:51 -0700)]
KVM: VMX: Don't expose unrestricted_guest is enabled if ept is disabled
SDM mentioned:
"If either the “unrestricted guest†VM-execution control or the “mode-based
execute control for EPT†VM- execution control is 1, the “enable EPTâ€
VM-execution control must also be 1."
However, we can still observe unrestricted_guest is Y after inserting the kvm-intel.ko
w/ ept=N. It depends on later starts a guest in order that the function
vmx_compute_secondary_exec_control() can be executed, then both the module parameter
and exec control fields will be amended.
This patch fixes it by amending module parameter immediately during vmcs data setup.
Reviewed-by: Jim Mattson <jmattson@google.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Jim Mattson <jmattson@google.com> Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Wanpeng Li [Wed, 11 Oct 2017 12:10:19 +0000 (05:10 -0700)]
KVM: X86: Processor States following Reset or INIT
- XCR0 is reset to 1 by RESET but not INIT
- XSS is zeroed by both RESET and INIT
- BNDCFGU, BND0-BND3, BNDCFGS, BNDSTATUS are zeroed by both RESET and INIT
This patch does this according to SDM.
Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Jim Mattson <jmattson@google.com> Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Radim Krčmář [Fri, 6 Oct 2017 17:25:55 +0000 (19:25 +0200)]
KVM: x86: thoroughly disarm LAPIC timer around TSC deadline switch
Our routines look at tscdeadline and period when deciding state of a
timer. The timer is disarmed when switching between TSC deadline and
other modes, so we should set everything to disarmed state.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Reviewed-by: Wanpeng Li <wanpeng.li@hotmail.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Shakeel Butt [Fri, 6 Oct 2017 01:07:24 +0000 (18:07 -0700)]
kvm, mm: account kvm related kmem slabs to kmemcg
The kvm slabs can consume a significant amount of system memory
and indeed in our production environment we have observed that
a lot of machines are spending significant amount of memory that
can not be left as system memory overhead. Also the allocations
from these slabs can be triggered directly by user space applications
which has access to kvm and thus a buggy application can leak
such memory. So, these caches should be accounted to kmemcg.
Signed-off-by: Shakeel Butt <shakeelb@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
No need for another enable_ept check. kvm->arch.ept_identity_map_addr
only has to be inititalized once. Having alloc_identity_pagetable() is
overkill and dropping BUG_ONs is always nice.
Wanpeng Li [Fri, 6 Oct 2017 14:38:32 +0000 (07:38 -0700)]
KVM: LAPIC: Apply change to TDCR right away to the timer
The description in the Intel SDM of how the divide configuration
register is used: "The APIC timer frequency will be the processor's bus
clock or core crystal clock frequency divided by the value specified in
the divide configuration register."
Observation of baremetal shown that when the TDCR is change, the TMCCT
does not change or make a big jump in value, but the rate at which it
count down change.
The patch update the emulation to APIC timer to so that a change to the
divide configuration would be reflected in the value of the counter and
when the next interrupt is triggered.
Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
[Fixed some whitespace and added a check for negative delta and running
timer. - Radim] Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Wanpeng Li [Fri, 6 Oct 2017 01:54:25 +0000 (18:54 -0700)]
KVM: LAPIC: Keep timer running when switching between one-shot and periodic mode
If we take TSC-deadline mode timer out of the picture, the Intel SDM
does not say that the timer is disable when the timer mode is change,
either from one-shot to periodic or vice versa.
After this patch, the timer is no longer disarmed on change of mode, so
the counter (TMCCT) keeps counting down.
So what does a write to LVTT changes ? On baremetal, the change of mode
is probably taken into account only when the counter reach 0. When this
happen, LVTT is use to figure out if the counter should restard counting
down from TMICT (so periodic mode) or stop counting (if one-shot mode).
This patch is based on observation of the behavior of the APIC timer on
baremetal as well as check that they does not go against the description
written in the Intel SDM.
Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
[Fixed rate limiting of periodic timer.] Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Wanpeng Li [Thu, 5 Oct 2017 10:53:51 +0000 (03:53 -0700)]
KVM: LAPIC: Fix lapic timer mode transition
SDM 10.5.4.1 TSC-Deadline Mode mentioned that "Transitioning between TSC-Deadline
mode and other timer modes also disarms the timer". So the APIC Timer Initial Count
Register for one-shot/periodic mode should be reset. This patch do it.
Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
[Removed unnecessary definition of APIC_LVT_TIMER_MASK.] Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Jeremy Cline [Wed, 4 Oct 2017 03:08:11 +0000 (03:08 +0000)]
tools/kvm_stat: Add Python 3 support to kvm_stat
Make kvm_stat support Python 3 by changing the use of "print" to a
function rather than a statement, switching from "iteritems" and
"iterkeys" (removed in Python 3) to "items" and "keys" respectively,
and decoding bytes to strings when dealing with text.
With this change, kvm_stat is usable with Python 2.6 and greater.
Signed-off-by: Jeremy Cline <jeremy@jcline.org> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Wanpeng Li [Fri, 29 Sep 2017 01:06:24 +0000 (18:06 -0700)]
KVM: VMX: Don't expose PLE enable if there is no hardware support
KVM doesn't expose the PLE capability to the L1 hypervisor, however,
ple_window still shows the default value on L1 hypervisor. This patch
fixes it by clearing all the PLE related module parameter if there is
no PLE capability.
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Haozhong Zhang [Tue, 10 Oct 2017 07:01:22 +0000 (15:01 +0800)]
KVM: nVMX: fix guest CR4 loading when emulating L2 to L1 exit
When KVM emulates an exit from L2 to L1, it loads L1 CR4 into the
guest CR4. Before this CR4 loading, the guest CR4 refers to L2
CR4. Because these two CR4's are in different levels of guest, we
should vmx_set_cr4() rather than kvm_set_cr4() here. The latter, which
is used to handle guest writes to its CR4, checks the guest change to
CR4 and may fail if the change is invalid.
The failure may cause trouble. Consider we start
a L1 guest with non-zero L1 PCID in use,
(i.e. L1 CR4.PCIDE == 1 && L1 CR3.PCID != 0)
and
a L2 guest with L2 PCID disabled,
(i.e. L2 CR4.PCIDE == 0)
and following events may happen:
1. If kvm_set_cr4() is used in load_vmcs12_host_state() to load L1 CR4
into guest CR4 (in VMCS01) for L2 to L1 exit, it will fail because
of PCID check. As a result, the guest CR4 recorded in L0 KVM (i.e.
vcpu->arch.cr4) is left to the value of L2 CR4.
2. Later, if L1 attempts to change its CR4, e.g., clearing VMXE bit,
kvm_set_cr4() in L0 KVM will think L1 also wants to enable PCID,
because the wrong L2 CR4 is used by L0 KVM as L1 CR4. As L1
CR3.PCID != 0, L0 KVM will inject GP to L1 guest.
Fixes: 4704d0befb072 ("KVM: nVMX: Exiting from L2 to L1") Cc: qemu-stable@nongnu.org Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Ladi Prosek [Thu, 5 Oct 2017 09:10:23 +0000 (11:10 +0200)]
KVM: MMU: always terminate page walks at level 1
is_last_gpte() is not equivalent to the pseudo-code given in commit 6bb69c9b69c31 ("KVM: MMU: simplify last_pte_bitmap") because an incorrect
value of last_nonleaf_level may override the result even if level == 1.
It is critical for is_last_gpte() to return true on level == 1 to
terminate page walks. Otherwise memory corruption may occur as level
is used as an index to various data structures throughout the page
walking code. Even though the actual bug would be wherever the MMU is
initialized (as in the previous patch), be defensive and ensure here
that is_last_gpte() returns the correct value.
This patch is also enough to fix CVE-2017-12188.
Fixes: 6bb69c9b69c315200ddc2bc79aee14c0184cf5b2 Cc: stable@vger.kernel.org Cc: Andy Honig <ahonig@google.com> Signed-off-by: Ladi Prosek <lprosek@redhat.com>
[Panic if walk_addr_generic gets an incorrect level; this is a serious
bug and it's not worth a WARN_ON where the recovery path might hide
further exploitable issues; suggested by Andrew Honig. - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Ladi Prosek [Thu, 5 Oct 2017 09:10:22 +0000 (11:10 +0200)]
KVM: nVMX: update last_nonleaf_level when initializing nested EPT
The function updates context->root_level but didn't call
update_last_nonleaf_level so the previous and potentially wrong value
was used for page walks. For example, a zero value of last_nonleaf_level
would allow a potential out-of-bounds access in arch/x86/mmu/paging_tmpl.h's
walk_addr_generic function (CVE-2017-12188).
Fixes: 155a97a3d7c78b46cef6f1a973c831bc5a4f82bb Signed-off-by: Ladi Prosek <lprosek@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Linus Torvalds [Sat, 7 Oct 2017 17:07:51 +0000 (10:07 -0700)]
Merge branch 'i2c/for-current-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C has three driver fixes for the newly introduced drivers and one ID
addition for the i801 driver"
* 'i2c/for-current-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i2c-stm32f7: make structure stm32f7_setup static const
i2c: ensure termination of *_device_id tables
i2c: i801: Add support for Intel Cedar Fork
i2c: stm32f7: fix setup structure
Linus Torvalds [Sat, 7 Oct 2017 17:03:03 +0000 (10:03 -0700)]
Merge tag 'mmc-v4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix driver strength selection when selecting hs400es
- Delete bounce buffer handling:
This change fixes a problem related to how bounce buffers are being
allocated. However, instead of trying to fix that, let's just
remove the mmc bounce buffer code altogether, as it has practically
no use.
MMC host:
- meson-gx: A couple of fixes related to clock/phase/tuning
- sdhci-xenon: Fix clock resource by adding an optional bus clock"
* tag 'mmc-v4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-xenon: Fix clock resource by adding an optional bus clock
mmc: meson-gx: include tx phase in the tuning process
mmc: meson-gx: fix rx phase reset
mmc: meson-gx: make sure the clock is rounded down
mmc: Delete bounce buffer handling
mmc: core: add driver strength selection when selecting hs400es
Linus Torvalds [Sat, 7 Oct 2017 00:59:32 +0000 (17:59 -0700)]
Merge tag 'hwmon-for-linus-v4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Fix up error path in xgene driver"
* tag 'hwmon-for-linus-v4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (xgene) Fix up error handling path mixup in 'xgene_hwmon_probe()'
Linus Torvalds [Fri, 6 Oct 2017 23:25:08 +0000 (16:25 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
- build fix to export the clk_bulk_prepare() symbol
- suspend fix for Samsung Exynos SoCs where we need to keep clks on
across suspend
- two critical clk markings for clks that shouldn't ever turn off on
Rockchip SoCs
- a fix for a copy-paste mistake on Rockchip rk3128 causing some clks
to touch the same bit and trample over one another
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: samsung: exynos4: Enable VPLL and EPLL clocks for suspend/resume cycle
clk: Export clk_bulk_prepare()
clk: rockchip: add sclk_timer5 as critical clock on rk3128
clk: rockchip: fix up rk3128 pvtm and mipi_24m gate regs error
clk: rockchip: add pclk_pmu as critical clock on rk3128
Linus Torvalds [Fri, 6 Oct 2017 22:57:08 +0000 (15:57 -0700)]
Merge tag 'arc-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC udpates from Vineet Gupta:
- updates for various platforms
- boot log updates for upcoming HS48 family of cores (dual issue)
* tag 'arc-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [plat-hsdk]: Add reset controller node to manage ethernet reset
ARC: [plat-hsdk]: Temporary fix to set CPU frequency to 1GHz
ARC: fix allnoconfig build warning
ARCv2: boot log: identify HS48 cores (dual issue)
ARC: boot log: decontaminate ARCv2 ISA_CONFIG register
arc: remove redundant UTS_MACHINE define in arch/arc/Makefile
ARC: [plat-eznps] Update platform maintainer as Noam left
ARC: [plat-hsdk] use actual clk driver to manage cpu clk
ARC: [*defconfig] Reenable soft lock-up detector
ARC: [plat-axs10x] sdio: Temporary fix of sdio ciu frequency
ARC: [plat-hsdk] sdio: Temporary fix of sdio ciu frequency
ARC: [plat-axs103] Add temporary quirk to reset ethernet IP
Linus Torvalds [Fri, 6 Oct 2017 22:53:36 +0000 (15:53 -0700)]
Merge tag 'xfs-4.14-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
- fix a race between overlapping copy on write aio
- fix cow fork swapping when we defragment reflinked files
* tag 'xfs-4.14-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: handle racy AIO in xfs_reflink_end_cow
xfs: always swap the cow forks when swapping extents
Linus Torvalds [Fri, 6 Oct 2017 19:13:50 +0000 (12:13 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A collection of fixes for this series. This contains:
- NVMe pull request from Christoph, one uuid attribute fix, and one
fix for the controller memory buffer address for remapped BARs.
- use-after-free fix for bsg, from Benjamin Block.
- bcache race/use-after-free fix for a list traversal, fixing a
regression in this merge window. From Coly Li.
- null_blk change configfs dependency change from a 'depends' to a
'select'. This is a change from this merge window as well. From me.
- nbd signal fix from Josef, fixing a regression introduced with the
status code changes.
- nbd MAINTAINERS mailing list entry update.
- blk-throttle stall fix from Joseph Qi.
- blk-mq-debugfs fix from Omar, fixing an issue where we don't
register the IO scheduler debugfs directory, if the driver is
loaded with it. Only shows up if you switch through the sysfs
interface"
* 'for-linus' of git://git.kernel.dk/linux-block:
bsg-lib: fix use-after-free under memory-pressure
nvme-pci: Use PCI bus address for data/queues in CMB
blk-mq-debugfs: fix device sched directory for default scheduler
null_blk: change configfs dependency to select
blk-throttle: fix possible io stall when upgrade to max
MAINTAINERS: update list for NBD
nbd: fix -ERESTARTSYS handling
nvme: fix visibility of "uuid" ns attribute
bcache: use llist_for_each_entry_safe() in __closure_wake_up()
Linus Torvalds [Fri, 6 Oct 2017 19:07:09 +0000 (12:07 -0700)]
Merge tag 'pci-v4.14-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Fix legacy IDE probe issues exposed by recent PCI core IRQ mapping
changes (Bartlomiej Zolnierkiewicz, Lorenzo Pieralisi)"
* tag 'pci-v4.14-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
ide: fix IRQ assignment for PCI bus order probing
ide: pci: free PCI BARs on initialization failure
ide: free hwif->portdev on hwif_init() failure
Linus Torvalds [Fri, 6 Oct 2017 18:31:46 +0000 (11:31 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Bring initialisation of user space undefined instruction handling
early (core_initcall) since late_initcall() happens after modprobe in
initramfs is invoked. Similar fix for fpsimd initialisation
- Increase the kernel stack when KASAN is enabled
- Bring the PCI ACS enabling earlier via the
iort_init_platform_devices()
- Fix misleading data abort address printing (decimal vs hex)
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Ensure fpsimd support is ready before userspace is active
arm64: Ensure the instruction emulation is ready for userspace
arm64: Use larger stacks when KASAN is selected
ACPI/IORT: Fix PCI ACS enablement
arm64: fix misleading data abort decoding
Linus Torvalds [Fri, 6 Oct 2017 18:28:34 +0000 (11:28 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
- fix PPC XIVE interrupt delivery
- fix x86 RCU breakage from asynchronous page faults when built without
PREEMPT_COUNT
- fix x86 build with -frecord-gcc-switches
- fix x86 build without X86_LOCAL_APIC
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: add X86_LOCAL_APIC dependency
x86/kvm: Move kvm_fastop_exception to .fixup section
kvm/x86: Avoid async PF preempting the kernel incorrectly
KVM: PPC: Book3S: Fix server always zero from kvmppc_xive_get_xive()
Linus Torvalds [Fri, 6 Oct 2017 18:25:55 +0000 (11:25 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"This is a pretty small pull request. Only 6 patches in total. There
are no outstanding -rc patches on the mailing list after this pull
request, so only if some new issues are discovered in the remainder of
the rc cycles will you hear from me again.
Summary:
- a fix for iwpm netlink usage
- a fix for error unwinding in mlx5
- two fixes to vlan handling in qedr
- a couple small i40iw fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
i40iw: Fix port number for query QP
i40iw: Add missing memory barriers
RDMA/qedr: Parse vlan priority as sl
RDMA/qedr: Parse VLAN ID correctly and ignore the value of zero
IB/mlx5: Fix label order in error path handling
RDMA/iwpm: Properly mark end of NL messages
Linus Torvalds [Fri, 6 Oct 2017 16:03:08 +0000 (09:03 -0700)]
Merge branch 'for-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"Two more fixes for bugs introduced in 4.13.
The sector_t problem with 32bit architecture and !LBDAF config seems
serious but the number of affected deployments is hopefully low.
The clashing status bits could lead to a confusing in-memory state of
the whole-filesystem operations if used with the quota override sysfs
knob"
* 'for-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: fix overlap of fs_info::flags values
btrfs: avoid overflow when sector_t is 32 bit
Linus Torvalds [Fri, 6 Oct 2017 16:01:45 +0000 (09:01 -0700)]
Merge tag 'ceph-for-4.14-rc4' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"Two fixups for CephFS snapshot-handling patches in -rc1"
* tag 'ceph-for-4.14-rc4' of git://github.com/ceph/ceph-client:
ceph: fix __choose_mds() for LSSNAP request
ceph: properly queue cap snap for newly created snap realm
Linus Torvalds [Fri, 6 Oct 2017 15:52:53 +0000 (08:52 -0700)]
Merge branch 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull overlayfs fixes from Miklos Szeredi:
"Fix a regression in 4.14 and one in 4.13. The latter is a case when
Docker is doing something it really shouldn't and gets away with it.
We now print a warning instead of erroring out.
There are also fixes to several error paths"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: fix regression caused by exclusive upper/work dir protection
ovl: fix missing unlock_rename() in ovl_do_copy_up()
ovl: fix dentry leak in ovl_indexdir_cleanup()
ovl: fix dput() of ERR_PTR in ovl_cleanup_index()
ovl: fix error value printed in ovl_lookup_index()
ovl: fix may_write_real() for overlayfs directories
Linus Torvalds [Fri, 6 Oct 2017 15:47:21 +0000 (08:47 -0700)]
Merge tag 'powerpc-4.14-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Nine small fixes, really nothing that stands out.
A work-around for a spurious MCE on Power9. A CXL fault handling fix,
some fixes to the new XIVE code, and a fix to the new 32-bit
STRICT_KERNEL_RWX code.
Fixes for old code/stable: an fix to an incorrect TLB flush on boot
but not on any current machines, a compile error on 4xx and a fix to
memory hotplug when using radix (Power9).
Thanks to: Anton Blanchard, Cédric Le Goater, Christian Lamparter,
Christophe Leroy, Christophe Lombard, Guenter Roeck, Jeremy Kerr,
Michael Neuling, Nicholas Piggin"
* tag 'powerpc-4.14-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/powernv: Increase memory block size to 1GB on radix
powerpc/mm: Call flush_tlb_kernel_range with interrupts enabled
powerpc/xive: Clear XIVE internal structures when a CPU is removed
powerpc/xive: Fix IPI reset
powerpc/4xx: Fix compile error with 64K pages on 40x, 44x
powerpc: Fix action argument for cpufeatures-based TLB flush
cxl: Fix memory page not handled
powerpc: Fix workaround for spurious MCE on POWER9
powerpc: Handle MCE on POWER9 with only DSISR bit 30 set
Linus Torvalds [Fri, 6 Oct 2017 15:42:06 +0000 (08:42 -0700)]
Merge tag 'drm-fixes-for-v4.14-rc4' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Some i915 fixes from the last two weeks (as they were on a strange
base and I just waited for rc3), also a single sun4i hdmi fix"
* tag 'drm-fixes-for-v4.14-rc4' of git://people.freedesktop.org/~airlied/linux:
drm/i915/glk: Fix DMC/DC state idleness calculation
drm/i915/cnl: Reprogram DMC firmware after S3/S4 resume
drm/i915: Fix DDI PHY init if it was already on
drm/sun4i: hdmi: Disable clks in bind function error path and unbind function
drm/i915/bios: ignore HDMI on port A
drm/i915: remove redundant variable hw_check
drm/i915: always update ELD connector type after get modes
Linus Torvalds [Fri, 6 Oct 2017 15:36:41 +0000 (08:36 -0700)]
Merge branch 'core-watchdog-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull watchddog clean-up and fixes from Thomas Gleixner:
"The watchdog (hard/softlockup detector) code is pretty much broken in
its current state. The patch series addresses this by removing all
duct tape and refactoring it into a workable state.
The reasons why I ask for inclusion that late in the cycle are:
1) The code causes lockdep splats vs. hotplug locking which get
reported over and over. Unfortunately there is no easy fix.
2) The risk of breakage is minimal because it's already broken
3) As 4.14 is a long term stable kernel, I prefer to have working
watchdog code in that and the lockdep issues resolved. I wouldn't
ask you to pull if 4.14 wouldn't be a LTS kernel or if the
solution would be easy to backport.
4) The series was around before the merge window opened, but then got
delayed due to the UP failure caused by the for_each_cpu()
surprise which we discussed recently.
Changes vs. V1:
- Addressed your review points
- Addressed the warning in the powerpc code which was discovered late
- Changed two function names which made sense up to a certain point
in the series. Now they match what they do in the end.
- Fixed a 'unused variable' warning, which got not detected by the
intel robot. I triggered it when trying all possible related config
combinations manually. Randconfig testing seems not random enough.
The changes have been tested by and reviewed by Don Zickus and tested
and acked by Micheal Ellerman for powerpc"
* 'core-watchdog-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
watchdog/core: Put softlockup_threads_initialized under ifdef guard
watchdog/core: Rename some softlockup_* functions
powerpc/watchdog: Make use of watchdog_nmi_probe()
watchdog/core, powerpc: Lock cpus across reconfiguration
watchdog/core, powerpc: Replace watchdog_nmi_reconfigure()
watchdog/hardlockup/perf: Fix spelling mistake: "permanetely" -> "permanently"
watchdog/hardlockup/perf: Cure UP damage
watchdog/hardlockup: Clean up hotplug locking mess
watchdog/hardlockup/perf: Simplify deferred event destroy
watchdog/hardlockup/perf: Use new perf CPU enable mechanism
watchdog/hardlockup/perf: Implement CPU enable replacement
watchdog/hardlockup/perf: Implement init time detection of perf
watchdog/hardlockup/perf: Implement init time perf validation
watchdog/core: Get rid of the racy update loop
watchdog/core, powerpc: Make watchdog_nmi_reconfigure() two stage
watchdog/sysctl: Clean up sysctl variable name space
watchdog/sysctl: Get rid of the #ifdeffery
watchdog/core: Clean up header mess
watchdog/core: Further simplify sysctl handling
watchdog/core: Get rid of the thread teardown/setup dance
...
arm64: Ensure fpsimd support is ready before userspace is active
We register the pm/hotplug callbacks for FPSIMD as late_initcall,
which happens after the userspace is active (from initramfs via
populate_rootfs, a rootfs_initcall). Make sure we are ready even
before the userspace could potentially use it, by promoting to
a core_initcall.
Cc: Will Deacon <will.deacon@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Dave Martin <dave.martin@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
arm64: Ensure the instruction emulation is ready for userspace
We trap and emulate some instructions (e.g, mrs, deprecated instructions)
for the userspace. However the handlers for these are registered as
late_initcalls and the userspace could be up and running from the initramfs
by that time (with populate_rootfs, which is a rootfs_initcall()). This
could cause problems for the early applications ending up in failure
like :
Anton Blanchard [Thu, 7 Sep 2017 05:05:51 +0000 (15:05 +1000)]
powerpc/powernv: Increase memory block size to 1GB on radix
Memory hot unplug on PowerNV radix hosts is broken. Our memory block
size is 256MB but since we map the linear region with very large
pages, each pte we tear down maps 1GB.
A hot unplug of one 256MB memory block results in 768MB of memory
getting unintentionally unmapped. At this point we are likely to oops.
Fix this by increasing our memory block size to 1GB on PowerNV radix
hosts.
Fixes: 4b5d62ca17a1 ("powerpc/mm: add radix__remove_section_mapping()") Cc: stable@vger.kernel.org # v4.11+ Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Dave Airlie [Fri, 6 Oct 2017 01:09:47 +0000 (11:09 +1000)]
Merge tag 'drm-misc-fixes-2017-10-05' of git://anongit.freedesktop.org/git/drm-misc into drm-fixes
One bugfix in sun4i for 4.14
* tag 'drm-misc-fixes-2017-10-05' of git://anongit.freedesktop.org/git/drm-misc:
drm/sun4i: hdmi: Disable clks in bind function error path and unbind function
Dave Airlie [Fri, 6 Oct 2017 01:09:29 +0000 (11:09 +1000)]
Merge tag 'drm-intel-fixes-2017-10-04' of git://anongit.freedesktop.org/git/drm-intel into drm-fixes
drm/i915 fixes for 4.14-rc4:
All 3 highest GLK bugs fixed by Imre:
- GLK drv reload - Fix DDI Phy init if it was already on.
- GLK suspend resume - Reprogram DMC firmware after s3/s4.
- GLK DC states - Fix idleness calculation.
* tag 'drm-intel-fixes-2017-10-04' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915/glk: Fix DMC/DC state idleness calculation
drm/i915/cnl: Reprogram DMC firmware after S3/S4 resume
drm/i915: Fix DDI PHY init if it was already on
Linus Torvalds [Thu, 5 Oct 2017 22:51:37 +0000 (15:51 -0700)]
Merge tag 'pm-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"This fixes a code ordering issue in the main suspend-to-idle loop that
causes some "low power S0 idle" conditions to be incorrectly reported
as unmet with suspend/resume debug messages enabled"
* tag 'pm-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / s2idle: Invoke the ->wake() platform callback earlier
Linus Torvalds [Thu, 5 Oct 2017 22:17:40 +0000 (15:17 -0700)]
Merge tag 'for-4.14/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- a stable fix for the alignment of the event number reported at the
end of the 'DM_LIST_DEVICES' ioctl.
- a couple stable fixes for the DM crypt target.
- a DM raid health status reporting fix.
* tag 'for-4.14/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm raid: fix incorrect status output at the end of a "recover" process
dm crypt: reject sector_size feature if device length is not aligned to it
dm crypt: fix memory leak in crypt_ctr_cipher_old()
dm ioctl: fix alignment of event number in the device list
dm raid: fix incorrect status output at the end of a "recover" process
There are three important fields that indicate the overall health and
status of an array: dev_health, sync_ratio, and sync_action. They tell
us the condition of the devices in the array, and the degree to which
the array is synchronized.
This commit fixes a condition that is reported incorrectly. When a member
of the array is being rebuilt or a new device is added, the "recover"
process is used to synchronize it with the rest of the array. When the
process is complete, but the sync thread hasn't yet been reaped, it is
possible for the state of MD to be:
mddev->recovery = [ MD_RECOVERY_RUNNING MD_RECOVERY_RECOVER MD_RECOVERY_DONE ]
curr_resync_completed = <max dev size> (but not MaxSector)
and all rdevs to be In_sync.
This causes the 'array_in_sync' output parameter that is passed to
rs_get_progress() to be computed incorrectly and reported as 'false' --
or not in-sync. This in turn causes the dev_health status characters to
be reported as all 'a', rather than the proper 'A'.
This can cause erroneous output for several seconds at a time when tools
will want to be checking the condition due to events that are raised at
the end of a sync process. Fix this by properly calculating the
'array_in_sync' return parameter in rs_get_progress().
Also, remove an unnecessary intermediate 'recovery_cp' variable in
rs_get_progress().
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Linus Torvalds [Thu, 5 Oct 2017 17:39:29 +0000 (10:39 -0700)]
Merge tag 'sound-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes, mostly with stable ones:
- X32 ABI fix for PCM; likely not so many people suffer from it, but
still better to fix
- Two minor kernel warning fixes on USB audio devices spotted by
syzkaller
- Regression fix of echoaudio due to its inconsistent dimension
- Fix for HBR support on Intel DP audio, on some recent chips
- USB-audio quirk for yet another Plantronics devices
- Fix for potential double-fetch in ASIHPI FIFO queue"
* tag 'sound-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usx2y: Suppress kernel warning at page allocation failures
Revert "ALSA: echoaudio: purge contradictions between dimension matrix members and total number of members"
ALSA: usb-audio: Check out-of-bounds access by corrupted buffer descriptor
ALSA: pcm: Fix structure definition for X32 ABI
ALSA: usb-audio: Add sample rate quirk for Plantronics C310/C520-M
ALSA: hda - program ICT bits to support HBR audio
ALSA: asihpi: fix a potential double-fetch bug when copying puhm
ALSA: compress: Remove unused variable
Linus Torvalds [Thu, 5 Oct 2017 17:28:12 +0000 (10:28 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID subsystem fixes from Jiri Kosina:
- buffer management size fix for i2c-hid driver, from Adrian Salido
- tool ID regression fixes for Wacom driver from Jason Gerecke
- a few small assorted fixes and a few device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
Revert "HID: multitouch: Support ALPS PTP stick with pid 0x120A"
HID: hidraw: fix power sequence when closing device
HID: wacom: Always increment hdev refcount within wacom_get_hdev_data
HID: wacom: generic: Clear ABS_MISC when tool leaves proximity
HID: wacom: generic: Send MSC_SERIAL and ABS_MISC when leaving prox
HID: i2c-hid: allocate hid buffers for real worst case
HID: rmi: Make sure the HID device is opened on resume
HID: multitouch: Support ALPS PTP stick with pid 0x120A
HID: multitouch: support buttons and trackpoint on Lenovo X1 Tab Gen2
HID: wacom: Correct coordinate system of touchring and pen twist
HID: wacom: Properly report negative values from Intuos Pro 2 Bluetooth
HID: multitouch: Fix system-control buttons not working
HID: add multi-input quirk for IDC6680 touchscreen
HID: wacom: leds: Don't try to control the EKR's read-only LEDs
HID: wacom: bits shifted too much for 9th and 10th buttons
Jens Axboe [Thu, 5 Oct 2017 16:44:04 +0000 (10:44 -0600)]
Merge branch 'nvme-4.14' of git://git.infradead.org/nvme into for-linus
Pull NVMe fixes from Christoph:
"A trivial one-liner from Martin to fix the visible of the uuid attr,
and another one (originally from Abhishek Shah, rewritten by me) to fix
the CMB addresses passed back to the controller in case of a system that
remaps BAR addresses between host and device."
1) Check iwlwifi 9000 reorder buffer out-of-space condition properly,
from Sara Sharon.
2) Fix RCU splat in qualcomm rmnet driver, from Subash Abhinov
Kasiviswanathan.
3) Fix session and tunnel release races in l2tp, from Guillaume Nault
and Sabrina Dubroca.
4) Fix endian bug in sctp_diag_dump(), from Dan Carpenter.
5) Several mlx5 driver fixes from the Mellanox folks (max flow counters
cap check, invalid memory access in IPoIB support, etc.)
6) tun_get_user() should bail if skb->len is zero, from Alexander
Potapenko.
7) Fix RCU lookups in inetpeer, from Eric Dumazet.
8) Fix locking in packet_do_bund().
9) Handle cb->start() error properly in netlink dump code, from Jason
A. Donenfeld.
10) Handle multicast properly in UDP socket early demux code. From Paolo
Abeni.
11) Several erspan bug fixes in ip_gre, from Xin Long.
12) Fix use-after-free in socket filter code, in order to handle the
fact that listener lock is no longer taken during the three-way TCP
handshake. From Eric Dumazet.
13) Fix infoleak in RTM_GETSTATS, from Nikolay Aleksandrov.
14) Fix tail call generation in x86-64 BPF JIT, from Alexei Starovoitov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (77 commits)
net: 8021q: skip packets if the vlan is down
bpf: fix bpf_tail_call() x64 JIT
net: stmmac: dwmac-rk: Add RK3128 GMAC support
rndis_host: support Novatel Verizon USB730L
net: rtnetlink: fix info leak in RTM_GETSTATS call
socket, bpf: fix possible use after free
mlxsw: spectrum_router: Track RIF of IPIP next hops
mlxsw: spectrum_router: Move VRF refcounting
net: hns3: Fix an error handling path in 'hclge_rss_init_hw()'
net: mvpp2: Fix clock resource by adding an optional bus clock
r8152: add Linksys USB3GIGV1 id
l2tp: fix l2tp_eth module loading
ip_gre: erspan device should keep dst
ip_gre: set tunnel hlen properly in erspan_tunnel_init
ip_gre: check packet length and mtu correctly in erspan_xmit
ip_gre: get key from session_id correctly in erspan_rcv
tipc: use only positive error codes in messages
ppp: fix __percpu annotation
udp: perform source validation for mcast early demux
IPv4: early demux can return an error code
...
Amir Goldstein [Fri, 29 Sep 2017 07:21:21 +0000 (10:21 +0300)]
ovl: fix regression caused by exclusive upper/work dir protection
Enforcing exclusive ownership on upper/work dirs caused a docker
regression: https://github.com/moby/moby/issues/34672.
Euan spotted the regression and pointed to the offending commit.
Vivek has brought the regression to my attention and provided this
reproducer:
Terminal 1:
mount -t overlay -o workdir=work,lowerdir=lower,upperdir=upper none
merged/
Terminal 2:
unshare -m
Terminal 1:
umount merged
mount -t overlay -o workdir=work,lowerdir=lower,upperdir=upper none
merged/
mount: /root/overlay-testing/merged: none already mounted or mount point
busy
To fix the regression, I replaced the error with an alarming warning.
With index feature enabled, mount does fail, but logs a suggestion to
override exclusive dir protection by disabling index.
Note that index=off mount does take the inuse locks, so a concurrent
index=off will issue the warning and a concurrent index=on mount will fail.
Documentation was updated to reflect this change.
Fixes: 2cac0c00a6cd ("ovl: get exclusive ownership on upper/work dirs") Cc: <stable@vger.kernel.org> # v4.13 Reported-by: Euan Kemp <euank@euank.com> Reported-by: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Amir Goldstein [Sun, 24 Sep 2017 19:19:10 +0000 (22:19 +0300)]
ovl: fix dentry leak in ovl_indexdir_cleanup()
index dentry was not released when breaking out of the loop
due to index verification error.
Fixes: 415543d5c64f ("ovl: cleanup bad and stale index entries on mount") Cc: <stable@vger.kernel.org> # v4.13 Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Colin Ian King [Mon, 18 Sep 2017 08:15:39 +0000 (09:15 +0100)]
i2c: i2c-stm32f7: make structure stm32f7_setup static const
The structure stm32f7_setup is local to the source and does not need
to be in global scope, make it static const.
Cleans up sparse warning:
symbol 'stm32f7_setup' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Jarkko Nikula [Thu, 21 Sep 2017 13:23:16 +0000 (16:23 +0300)]
i2c: i801: Add support for Intel Cedar Fork
Add PCI ID for Intel Cedar Fork PCH.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the vlan is down, free the packet instead of proceeding with other
processing, or counting it as received. If vlan interfaces are used
as slaves for bonding, with arp monitoring for connectivity, if the rx
counter is seen to be incrementing, then the bond device will not
observe that the interface is down.
CC: David S. Miller <davem@davemloft.net> Signed-off-by: Vishakha Narvekar <Vishakha.Narvekar@dell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 5 Oct 2017 00:16:05 +0000 (17:16 -0700)]
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Our first batch of fixes this release cycle, unfortunately a bit
noisier than usual. Two major groups stand out:
- Some pinctril dts/dtsi changes for stm32 due to a new driver being
merged during the merge window, and this aligns the DT contents
between the old format and the new. This could arguably be moved to
the next merge window but it also seemed relatively harmless to
include now.
- Amlogic/meson had driver changes merged that required devicetree
changes to avoid functional/performance regressions. I've already
asked them to be more careful about this going forward, and making
sure drivers are compatible with older DTs when they make these
kind of changes. The platform is actively being upstreamed so
there's a few things in flight, we've seen this happen before and
sometimes it's hard to catch in time.
Besides that there is the usual mix of minor fixes"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
ARM: dts: stm32: use right pinctrl compatible for stm32f469
ARM: dts: stm32: Fix STMPE1600 binding on stm32429i-eval board
ARM: defconfig: update Gemini defconfig
ARM: defconfig: FRAMEBUFFER_CONSOLE can no longer be =m
arm64: dts: rockchip: add the grf clk for dw-mipi-dsi on rk3399
reset: Restrict RESET_HSDK to ARC_SOC_HSDK or COMPILE_TEST
ARM: dts: da850-evm: add serial and ethernet aliases
ARM: dts: am43xx-epos-evm: Remove extra CPSW EMAC entry
ARM: dts: am33xx: Add spi alias to match SOC schematics
ARM: OMAP2+: hsmmc: fix logic to call either omap_hsmmc_init or omap_hsmmc_late_init but not both
ARM: dts: dra7: Set a default parent to mcasp3_ahclkx_mux
ARM: OMAP2+: dra7xx: Set OPT_CLKS_IN_RESET flag for gpio1
ARM: dts: nokia n900: drop unneeded/undocumented parts of the dts
arm64: dts: rockchip: Correct MIPI DPHY PLL clock on rk3399
arm64: dt marvell: Fix AP806 system controller size
MAINTAINERS: add Macchiatobin maintainers entry
ARC: reset: remove the misleading v1 suffix all over
ARC: reset: add missing DT binding documentation for HSDKv1 reset driver
ARC: reset: Only build on archs that have IOMEM
ARM: at91: Replace uses of virt_to_phys with __pa_symbol
...
James Hogan [Wed, 4 Oct 2017 22:10:59 +0000 (23:10 +0100)]
Update James Hogan's email address
Update my imgtec.com and personal email address to my kernel.org one in
a few places as MIPS will soon no longer be part of Imagination
Technologies, and add mappings in .mailcap so get_maintainer.pl reports
the right address.
Signed-off-by: James Hogan <jhogan@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mustafa Ismail [Tue, 3 Oct 2017 16:11:49 +0000 (11:11 -0500)]
i40iw: Add missing memory barriers
Remove duplicate set_64bit_val call to offset 24.
Replace some instances of set_64bit_val with
i40iw_insert_wqe_hdr as valid bit needs a write
barrier and should be the last write operation for the WQE.
Amrani, Ram [Tue, 3 Oct 2017 11:47:26 +0000 (14:47 +0300)]
RDMA/qedr: Parse VLAN ID correctly and ignore the value of zero
Rename vlan_id field name to vlan as it contains more than the vlan_id.
Mask out non vlan id fields from vlan tag of the QED LL2 RX GSI
vlan output. As it is expected to be vlan id only.
Ignore vlan_id with value of zero.
Olof Johansson [Wed, 4 Oct 2017 17:31:00 +0000 (10:31 -0700)]
Merge tag 'stm32-dt-fixes-for-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into fixes
STM32 fixes for v4.14:
---------------------
-Fix STMPE1600 bindings for stm32429i-eval board
-Use right compatible for stm32f469 pinctrl. It implies to use
pinctrl dedicated files for F4 SoCs.
* tag 'stm32-dt-fixes-for-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: use right pinctrl compatible for stm32f469
ARM: dts: stm32: Fix STMPE1600 binding on stm32429i-eval board
Mark Rutland [Tue, 3 Oct 2017 17:25:46 +0000 (18:25 +0100)]
arm64: Use larger stacks when KASAN is selected
AddressSanitizer instrumentation can significantly bloat the stack, and
with GCC 7 this can result in stack overflows at boot time in some
configurations.
We can avoid this by doubling our stack size when KASAN is in use, as is
already done on x86 (and has been since KASAN was introduced).
Regardless of other patches to decrease KASAN's stack utilization,
kernels built with KASAN will always require more stack space than those
built without, and we should take this into account.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
commit f6810c15cf97 ("iommu/arm-smmu: Clean up early-probing
workarounds") removed kernel code that was allowing to initialize
and probe the SMMU devices early (ie earlier than PCI devices, through
linker script callback entries) in the boot process because it was not
needed any longer in that the SMMU devices/drivers now support deferred
probing.
Since the SMMUs probe routines are also in charge of requesting global
PCI ACS kernel enablement, commit f6810c15cf97 ("iommu/arm-smmu: Clean
up early-probing workarounds") also postponed PCI ACS enablement to
SMMUs devices probe time, which is too late given that PCI devices needs
to detect if PCI ACS is enabled to init the respective capability
through the following call path:
Add code in the ACPI IORT SMMU platform devices initialization path
(that is called before ACPI PCI enumeration) to detect if there
exists firmware mappings to map root complexes ids to SMMU ids
and if so enable ACS for the system.
Fixes: f6810c15cf97 ("iommu/arm-smmu: Clean up early-probing workarounds") Reviewed-by: Robin Murphy <robin.murphy@arm.com> Tested-by: Nate Watterson <nwatters@codeaurora.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: Hanjun Guo <hanjun.guo@linaro.org> Cc: Sudeep Holla <sudeep.holla@arm.com> Cc: Zhou Wang <wangzhou1@hisilicon.com> Cc: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Linus Torvalds [Wed, 4 Oct 2017 16:30:50 +0000 (09:30 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"A lot of stuff, sorry about that. A week on a beach, then a bunch of
time catching up then more time letting it bake in -next. Shan't do
that again!"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (51 commits)
include/linux/fs.h: fix comment about struct address_space
checkpatch: fix ignoring cover-letter logic
m32r: fix build failure
lib/ratelimit.c: use deferred printk() version
kernel/params.c: improve STANDARD_PARAM_DEF readability
kernel/params.c: fix an overflow in param_attr_show
kernel/params.c: fix the maximum length in param_get_string
mm/memory_hotplug: define find_{smallest|biggest}_section_pfn as unsigned long
mm/memory_hotplug: change pfn_to_section_nr/section_nr_to_pfn macro to inline function
kernel/kcmp.c: drop branch leftover typo
memremap: add scheduling point to devm_memremap_pages
mm, page_alloc: add scheduling point to memmap_init_zone
mm, memory_hotplug: add scheduling point to __add_pages
lib/idr.c: fix comment for idr_replace()
mm: memcontrol: use vmalloc fallback for large kmem memcg arrays
kernel/sysctl.c: remove duplicate UINT_MAX check on do_proc_douintvec_conv()
include/linux/bitfield.h: remove 32bit from FIELD_GET comment block
lib/lz4: make arrays static const, reduces object code size
exec: binfmt_misc: kill the onstack iname[BINPRM_BUF_SIZE] array
exec: binfmt_misc: fix race between load_misc_binary() and kill_node()
...
Boqun Feng [Tue, 3 Oct 2017 13:36:51 +0000 (21:36 +0800)]
kvm/x86: Avoid async PF preempting the kernel incorrectly
Currently, in PREEMPT_COUNT=n kernel, kvm_async_pf_task_wait() could call
schedule() to reschedule in some cases. This could result in
accidentally ending the current RCU read-side critical section early,
causing random memory corruption in the guest, or otherwise preempting
the currently running task inside between preempt_disable and
preempt_enable.
The difficulty to handle this well is because we don't know whether an
async PF delivered in a preemptible section or RCU read-side critical section
for PREEMPT_COUNT=n, since preempt_disable()/enable() and rcu_read_lock/unlock()
are both no-ops in that case.
To cure this, we treat any async PF interrupting a kernel context as one
that cannot be preempted, preventing kvm_async_pf_task_wait() from choosing
the schedule() path in that case.
To do so, a second parameter for kvm_async_pf_task_wait() is introduced,
so that we know whether it's called from a context interrupting the
kernel, and the parameter is set properly in all the callsites.
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Wanpeng Li <wanpeng.li@hotmail.com> Cc: stable@vger.kernel.org Signed-off-by: Boqun Feng <boqun.feng@gmail.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Linus Torvalds [Wed, 4 Oct 2017 16:21:58 +0000 (09:21 -0700)]
Merge branch 'fixes-v4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull smack fix from James Morris:
"It fixes a bug in xattr_getsecurity() where security_release_secctx()
was being called instead of kfree(), which leads to a memory leak in
the capabilities code. smack_inode_getsecurity is also fixed to behave
correctly when called from there"
* 'fixes-v4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
lsm: fix smack_inode_removexattr and xattr_getsecurity memleak
Marek Szyprowski [Tue, 19 Sep 2017 10:01:08 +0000 (12:01 +0200)]
clk: samsung: exynos4: Enable VPLL and EPLL clocks for suspend/resume cycle
Commit 6edfa11cb396 ("clk: samsung: Add enable/disable operation for
PLL36XX clocks") added enable/disable operations to PLL clocks. Prior that
VPLL and EPPL clocks were always enabled because the enable bit was never
touched. Those clocks have to be enabled during suspend/resume cycle,
because otherwise board fails to enter sleep mode. This patch enables them
unconditionally before entering system suspend state. System restore
function will set them to the previous state saved in the register cache
done before that unconditional enable.
Fixes: 6edfa11cb396 ("clk: samsung: Add enable/disable operation for PLL36XX clocks") CC: stable@vger.kernel.org # v4.13 Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Linus Torvalds [Wed, 4 Oct 2017 15:34:01 +0000 (08:34 -0700)]
Merge tag 'trace-v4.14-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixlets from Steven Rostedt:
"Two updates:
- A memory fix with left over code from spliting out ftrace_ops and
function graph tracer, where the function graph tracer could reset
the trampoline pointer, leaving the old trampoline not to be freed
(memory leak).
- The update to Paul's patch that added the unnecessary READ_ONCE().
This removes the unnecessary READ_ONCE() instead of having to
rebase the branch to update the patch that added it"
* tag 'trace-v4.14-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
rcu: Remove extraneous READ_ONCE()s from rcu_irq_{enter,exit}()
ftrace: Fix kmemleak in unregister_ftrace_graph
Milan Broz [Wed, 13 Sep 2017 13:45:56 +0000 (15:45 +0200)]
dm crypt: reject sector_size feature if device length is not aligned to it
If a crypt mapping uses optional sector_size feature, additional
restrictions to mapped device segment size must be applied in
constructor, otherwise the device activation will fail later.
Fixes: 8f0009a225 ("dm crypt: optionally support larger encryption sector size") Cc: stable@vger.kernel.org # 4.12+ Signed-off-by: Milan Broz <gmazyland@gmail.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Benjamin Block [Tue, 3 Oct 2017 10:48:37 +0000 (12:48 +0200)]
bsg-lib: fix use-after-free under memory-pressure
When under memory-pressure it is possible that the mempool which backs
the 'struct request_queue' will make use of up to BLKDEV_MIN_RQ count
emergency buffers - in case it can't get a regular allocation. These
buffers are preallocated and once they are also used, they are
re-supplied with old finished requests from the same request_queue (see
mempool_free()).
The bug is, when re-supplying the emergency pool, the old requests are
not again ran through the callback mempool_t->alloc(), and thus also not
through the callback bsg_init_rq(). Thus we skip initialization, and
while the sense-buffer still should be good, scsi_request->cmd might
have become to be an invalid pointer in the meantime. When the request
is initialized in bsg.c, and the user's CDB is larger than BLK_MAX_CDB,
bsg will replace it with a custom allocated buffer, which is freed when
the user's command is finished, thus it dangles afterwards. When next a
command is sent by the user that has a smaller/similar CDB as
BLK_MAX_CDB, bsg will assume that scsi_request->cmd is backed by
scsi_request->__cmd, will not make a custom allocation, and write into
undefined memory.
Fix this by splitting bsg_init_rq() into two functions:
- bsg_init_rq() is changed to only do the allocation of the
sense-buffer, which is used to back the bsg job's reply buffer. This
pointer should never change during the lifetime of a scsi_request, so
it doesn't need re-initialization.
- bsg_initialize_rq() is a new function that makes use of
'struct request_queue's initialize_rq_fn callback (which was
introduced in v4.12). This is always called before the request is
given out via blk_get_request(). This function does the remaining
initialization that was previously done in bsg_init_rq(), and will
also do it when the request is taken from the emergency-pool of the
backing mempool.
Fixes: 50b4d485528d ("bsg-lib: fix kernel panic resulting from missing allocation of reply-buffer") Cc: <stable@vger.kernel.org> # 4.11+ Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
projects / mirror_ubuntu-bionic-kernel.git / log