Commit e5afdf9dd515 ("powerpc/vfio_spapr_tce: Add reference counting to
iommu_table") missed an iommu_table allocation in the pseries vio code.
The iommu_table is allocated with kzalloc and as a result the associated
kref gets a value of zero. This has the side effect that during a DLPAR
remove of the associated virtual IOA the iommu_tce_table_put() triggers
a use-after-free underflow warning.
If we compile tools/acpi target in the top source directory, we'd get a
compilation error showing as bellow:
# make tools/acpi
DESCEND power/acpi
DESCEND tools/acpidbg
CC tools/acpidbg/acpidbg.o
Assembler messages:
Fatal error: can't create /home/lzy/kernel-upstream/power/acpi/\
tools/acpidbg/acpidbg.o: No such file or directory
../../Makefile.rules:26: recipe for target '/home/lzy/kernel-upstream/\
power/acpi/tools/acpidbg/acpidbg.o' failed
make[3]: *** [/home/lzy/kernel-upstream//power/acpi/tools/acpidbg/\
acpidbg.o] Error 1
Makefile:19: recipe for target 'acpidbg' failed
make[2]: *** [acpidbg] Error 2
Makefile:54: recipe for target 'acpi' failed
make[1]: *** [acpi] Error 2
Makefile:1607: recipe for target 'tools/acpi' failed
make: *** [tools/acpi] Error 2
Fixes: d5a4b1a540b8 ("tools/power/acpi: Remove direct kernel source include reference") Signed-off-by: Zhengyuan Liu <liuzhengyuan@kylinos.cn> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently the maximum rate for peripheral clock is calculated based on a
typical 133MHz MCK. The maximum frequency is defined in the datasheet as a
ratio to MCK. Some sama5d3 platforms are using a 166MHz MCK. Update the
device trees to match the maximum rate based on 166MHz.
The driver gets driver_data from memory that is marked as const (which
is probably put to read-only memory) and it then modifies it. This
likely causes some sort of fault to happen.
Fix this by taking a copy of the structure.
Fixes: c94a8ff14de3 ("platform/x86: intel_mid_powerbtn: make mid_pb_ddata const") Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The rtc-cmos interrupt setting was changed in the commit 079062b28fb4
("rtc: cmos: prevent kernel warning on IRQ flags mismatch") in order
to allow shared interrupts; according to that commit's description,
some machine got kernel warnings due to the interrupt line being shared
between rtc-cmos and other hardware, and rtc-cmos didn't allow IRQ sharing
that time.
After the aforementioned commit though it was observed a huge increase
in lost HPET interrupts in some systems, observed through the following
kernel message:
[...] hpet1: lost 35 rtc interrupts
After investigation, it was narrowed down to the shared interrupts
usage when having the kernel option "irqpoll" enabled. In this case,
all IRQ handlers are called for non-timer interrupts, if such handlers
are setup in shared IRQ lines. The rtc-cmos IRQ handler could be set to
hpet_rtc_interrupt(), which will produce the kernel "lost interrupts"
message after doing work - lots of readl/writel to HPET registers, which
are known to be slow.
Although "irqpoll" is not a default kernel option, it's used in some contexts,
one being the kdump kernel (which is an already "impaired" kernel usually
running with 1 CPU available), so the performance burden could be considerable.
Also, the same issue would happen (in a shorter extent though) when using
"irqfixup" kernel option.
In a quick experiment, a virtual machine with uptime of 2 minutes produced
>300 calls to hpet_rtc_interrupt() when "irqpoll" was set, whereas without
sharing interrupts this number reduced to 1 interrupt. Machines with more
hardware than a VM should generate even more unnecessary HPET interrupts
in this scenario.
---8<---8<---8<---
After looking into the rtc-cmos driver history and DSDT table from
the Microsoft Surface 3, we may notice that Hans de Goede submitted
a correct fix (see dependency below). Thus, we simply revert
the culprit commit.
Fixes: 079062b28fb4 ("rtc: cmos: prevent kernel warning on IRQ flags mismatch")
Depends-on: a1e23a42f1bd ("rtc: cmos: Do not assume irq 8 for rtc when there are no legacy irqs") Reported-by: Guilherme G. Piccoli <gpiccoli@canonical.com> Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Guilherme G. Piccoli <gpiccoli@canonical.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20200123131437.28157-1-andriy.shevchenko@linux.intel.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The current code returns -EPERM when the voltage loss bit is set.
Since the bit indicates that the time value is not valid, return
-EINVAL instead, which is the appropriate error code for this
situation.
Instead of making assumptions about the commit verifier contents, change
the commit code to ensure we always check that the verifier was set
by the XDR code.
Fixes: f54bcf2ecee9 ("pnfs: Prepare for flexfiles by pulling out common code") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If CONFIG_SWAP=n, it does not make much sense to offer the user the
option to enable support for swapping over NFS, as that will still fail
at run time:
# swapon /swap
swapon: /swap: swapon failed: Function not implemented
Fix this by adding a dependency on CONFIG_SWAP.
Fixes: a564b8f0398636ba ("nfs: enable swap on NFS") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Some PCI bridges implement BARs in addition to bridge windows. For
example, here's a PLX switch:
04:00.0 PCI bridge: PLX Technology, Inc. PEX 8724 24-Lane, 6-Port PCI
Express Gen 3 (8 GT/s) Switch, 19 x 19mm FCBGA (rev ca)
(prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 30, NUMA node 0
Memory at 90a00000 (32-bit, non-prefetchable) [size=256K]
Bus: primary=04, secondary=05, subordinate=0a, sec-latency=0
I/O behind bridge: 00002000-00003fff
Memory behind bridge: 90000000-909fffff
Prefetchable memory behind bridge: 0000380000800000-0000380000bfffff
Previously, when the kernel assigned resource addresses (with the
pci=realloc command line parameter, for example) it could clear the struct
resource corresponding to the BAR. When this happened, lspci would report
this BAR as "ignored":
Region 0: Memory at <ignored> (32-bit, non-prefetchable) [size=256K]
This is because the kernel reports a zero start address and zero flags
in the corresponding sysfs resource file and in /proc/bus/pci/devices.
Investigation with 'lspci -x', however, shows the BIOS-assigned address
will still be programmed in the device's BAR registers.
It's clearly a bug that the kernel lost track of the BAR value, but in most
cases, this still won't result in a visible issue because nothing uses the
memory, so nothing is affected. However, when an IOMMU is in use, it will
not reserve this space in the IOVA because the kernel no longer thinks the
range is valid. (See dmar_init_reserved_ranges() for the Intel
implementation of this.)
Without the proper reserved range, a DMA mapping may allocate an IOVA that
matches a bridge BAR, which results in DMA accesses going to the BAR
instead of the intended RAM.
The problem was in pci_assign_unassigned_root_bus_resources(). When any
resource from a bridge device fails to get assigned, the code set the
resource's flags to zero. This makes sense for bridge windows, as they
will be re-enabled later, but for regular BARs, it makes the kernel
permanently lose track of the fact that they decode address space.
Change pci_assign_unassigned_root_bus_resources() and
pci_assign_unassigned_bridge_resources() so they only clear "res->flags"
for bridge *windows*, not bridge BARs.
Fixes: da7822e5ad71 ("PCI: update bridge resources to get more big ranges when allocating space (again)") Link: https://lore.kernel.org/r/20200108213208.4612-1-logang@deltatee.com
[bhelgaas: commit log, check for pci_is_bridge()] Reported-by: Kit Chow <kchow@gigaio.com> Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A non-zero error value likely being returned by ufshcd_scsi_add_wlus() in
case of failure of adding the WLs, but ufshcd_probe_hba() doesn't use this
value, and doesn't report this failure to upper caller. This patch is to
fix this issue.
Fixes: 2a8fa600445c ("ufs: manually add well known logical units") Link: https://lore.kernel.org/r/20200120130820.1737-2-huobean@gmail.com Reviewed-by: Asutosh Das <asutoshd@codeaurora.org> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com> Reviewed-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Bean Huo <beanhuo@micron.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In rdma_nl_rcv_skb(), the local variable err is assigned the return value
of the supplied callback function, which could be one of
ib_nl_handle_resolve_resp(), ib_nl_handle_set_timeout(), or
ib_nl_handle_ip_res_resp(). These three functions all return skb->len on
success.
rdma_nl_rcv_skb() is merely a copy of netlink_rcv_skb(). The callback
functions used by the latter have the convention: "Returns 0 on success or
a negative error code".
In particular, the statement (equal for both functions):
if (nlh->nlmsg_flags & NLM_F_ACK || err)
implies that rdma_nl_rcv_skb() always will ack a message, independent of
the NLM_F_ACK being set in nlmsg_flags or not.
The fix could be to change the above statement, but it is better to keep
the two *_rcv_skb() functions equal in this respect and instead change the
three callback functions in the rdma subsystem to the correct convention.
Fixes: 2ca546b92a02 ("IB/sa: Route SA pathrecord query through netlink") Fixes: ae43f8286730 ("IB/core: Add IP to GID netlink offload") Link: https://lore.kernel.org/r/20191216120436.3204814-1-haakon.bugge@oracle.com Suggested-by: Mark Haywood <mark.haywood@oracle.com> Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com> Tested-by: Mark Haywood <mark.haywood@oracle.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Reviewed-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently, hv_sock restricts the port the guest socket can accept
connections on. hv_sock divides the socket port namespace into two parts
for server side (listening socket), 0-0x7FFFFFFF & 0x80000000-0xFFFFFFFF
(there are no restrictions on client port namespace). The first part
(0-0x7FFFFFFF) is reserved for sockets where connections can be accepted.
The second part (0x80000000-0xFFFFFFFF) is reserved for allocating ports
for the peer (host) socket, once a connection is accepted.
This reservation of the port namespace is specific to hv_sock and not
known by the generic vsock library (ex: af_vsock). This is problematic
because auto-binds/ephemeral ports are handled by the generic vsock
library and it has no knowledge of this port reservation and could
allocate a port that is not compatible with hv_sock (and legitimately so).
The issue hasn't surfaced so far because the auto-bind code of vsock
(__vsock_bind_stream) prior to the change 'VSOCK: bind to random port for
VMADDR_PORT_ANY' would start walking up from LAST_RESERVED_PORT (1023) and
start assigning ports. That will take a large number of iterations to hit
0x7FFFFFFF. But, after the above change to randomize port selection, the
issue has started coming up more frequently.
There has really been no good reason to have this port reservation logic
in hv_sock from the get go. Reserving a local port for peer ports is not
how things are handled generally. Peer ports should reflect the peer port.
This fixes the issue by lifting the port reservation, and also returns the
right peer port. Since the code converts the GUID to the peer port (by
using the first 4 bytes), there is a possibility of conflicts, but that
seems like a reasonable risk to take, given this is limited to vsock and
that only applies to all local sockets.
Signed-off-by: Sunil Muthuswamy <sunilmut@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently, the trigger orders SND_SOC_DPCM_TRIGGER_PRE/POST
determine the order in which FE DAI and BE DAI are triggered.
In the case of SND_SOC_DPCM_TRIGGER_PRE, the FE DAI is
triggered before the BE DAI and in the case of
SND_SOC_DPCM_TRIGGER_POST, the BE DAI is triggered before
the FE DAI. And this order remains the same irrespective of the
trigger command.
In the case of the SOF driver, during playback, the FW
expects the BE DAI to be triggered before the FE DAI during
the START trigger. The BE DAI trigger handles the starting of
Link DMA and so it must be started before the FE DAI is started
to prevent xruns during pause/release. This can be addressed
by setting the trigger order for the FE dai link to
SND_SOC_DPCM_TRIGGER_POST. But during the STOP trigger,
the FW expects the FE DAI to be triggered before the BE DAI.
Retaining the same order during the START and STOP commands,
results in FW error as the DAI component in the FW is still
active.
The issue can be fixed by mirroring the trigger order of
FE and BE DAI's during the START and STOP trigger. So, with the
trigger order set to SND_SOC_DPCM_TRIGGER_PRE, the FE DAI will be
trigger first during SNDRV_PCM_TRIGGER_START/STOP/RESUME
and the BE DAI will be triggered first during the
STOP/SUSPEND/PAUSE commands. Conversely, with the trigger order
set to SND_SOC_DPCM_TRIGGER_POST, the BE DAI will be triggered
first during the SNDRV_PCM_TRIGGER_START/STOP/RESUME commands
and the FE DAI will be triggered first during the
SNDRV_PCM_TRIGGER_STOP/SUSPEND/PAUSE commands.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20191104224812.3393-2-ranjani.sridharan@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The recent patch that substituted a flag on an rxrpc_call for the
connection pointer being NULL as an indication that a call was disconnected
puts the set_bit in the wrong place for service calls. This is only a
problem if a call is implicitly terminated by a new call coming in on the
same connection channel instead of a terminating ACK packet.
In such a case, rxrpc_input_implicit_end_call() calls
__rxrpc_disconnect_call(), which is now (incorrectly) setting the
disconnection bit, meaning that when rxrpc_release_call() is later called,
it doesn't call rxrpc_disconnect_call() and so the call isn't removed from
the peer's error distribution list and the list gets corrupted.
KASAN finds the issue as an access after release on a call, but the
position at which it occurs is confusing as it appears to be related to a
different call (the call site is where the latter call is being removed
from the error distribution list and either the next or pprev pointer
points to a previously released call).
Fix this by moving the setting of the flag from __rxrpc_disconnect_call()
to rxrpc_disconnect_call() in the same place that the connection pointer
was being cleared.
Fixes: 5273a191dca6 ("rxrpc: Fix NULL pointer deref due to call->conn being cleared on disconnect") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Decreasing sysctl_perf_event_mlock between two consecutive perf_mmap()s of
a perf ring buffer may lead to an integer underflow in locked memory
accounting. This may lead to the undesired behaviors, such as failures in
BPF map creation.
Address this by adjusting the accounting logic to take into account the
possibility that the amount of already locked memory may exceed the
current limit.
Fixes: c4b75479741c ("perf/core: Make the mlock accounting simple again") Suggested-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: <stable@vger.kernel.org> Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Link: https://lkml.kernel.org/r/20200123181146.2238074-1-songliubraving@fb.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
kernel BUG at kernel/time/timer.c:1154!
BUG_ON(timer_pending(timer) || !timer->function) in add_timer_on().
At the same time another cpu got:
general protection fault: 0000 [#1] SMP PTI of poinson pointer 0xdead000000000200 in:
__hlist_del at include/linux/list.h:681
(inlined by) detach_timer at kernel/time/timer.c:818
(inlined by) expire_timers at kernel/time/timer.c:1355
(inlined by) __run_timers at kernel/time/timer.c:1686
(inlined by) run_timer_softirq at kernel/time/timer.c:1699
Unfortunately kernel logs are badly scrambled, stacktraces are lost.
Printing the timer->function before the BUG_ON() pointed to
clocksource_watchdog().
The execution of clocksource_watchdog() can race with a sequence of
clocksource_stop_watchdog() .. clocksource_start_watchdog():
If we have a soft mount we should fail commands for session-setup
failures (such as the password having changed/ account being deleted/ ...)
and return an error back to the application.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The initial CPU reset clobbers the userspace fpc and the store status
ioctl clobbers the guest acrs + fpr. As these calls are only done via
ioctl (and not via vcpu_run), no CPU context is loaded, so we can (and
must) act directly on the sync regs, not on the thread context.
Cc: stable@kernel.org Fixes: e1788bb995be ("KVM: s390: handle floating point registers in the run ioctl not in vcpu_put/load") Fixes: 31d8b8d41a7e ("KVM: s390: handle access registers in the run ioctl not in vcpu_put/load") Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Reviewed-by: David Hildenbrand <david@redhat.com> Reviewed-by: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Janosch Frank <frankja@linux.ibm.com> Link: https://lore.kernel.org/r/20200131100205.74720-2-frankja@linux.ibm.com Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Avoid the "writable" check in __gfn_to_hva_many(), which will always fail
on read-only memslots due to gfn_to_hva() assuming writes. Functionally,
this allows x86 to create large mappings for read-only memslots that
are backed by HugeTLB mappings.
Note, the changelog for commit 05da45583de9 ("KVM: MMU: large page
support") states "If the largepage contains write-protected pages, a
large pte is not used.", but "write-protected" refers to pages that are
temporarily read-only, e.g. read-only memslots didn't even exist at the
time.
Fixes: 4d8b81abc47b ("KVM: introduce readonly memslot") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
[Redone using kvm_vcpu_gfn_to_memslot_prot. - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In case writing to vmread destination operand result in a #PF, vmread
should not call nested_vmx_succeed() to set rflags to specify success.
Similar to as done in VMPTRST (See handle_vmptrst()).
Reviewed-by: Liran Alon <liran.alon@oracle.com> Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Cc: stable@vger.kernel.org Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Remove the bogus 64-bit only condition from the check that disables MMIO
spte optimization when the system supports the max PA, i.e. doesn't have
any reserved PA bits. 32-bit KVM always uses PAE paging for the shadow
MMU, and per Intel's SDM:
PAE paging translates 32-bit linear addresses to 52-bit physical
addresses.
The kernel's restrictions on max physical addresses are limits on how
much memory the kernel can reasonably use, not what physical addresses
are supported by hardware.
Fixes: ce88decffd17 ("KVM: MMU: mmio page fault support") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Unlike most state managed by XSAVE, MPX is initialized to zero on INIT.
Because INITs are usually recognized in the context of a VCPU_RUN call,
kvm_vcpu_reset() puts the guest's FPU so that the FPU state is resident
in memory, zeros the MPX state, and reloads FPU state to hardware. But,
in the unlikely event that an INIT is recognized during
kvm_arch_vcpu_ioctl_get_mpstate() via kvm_apic_accept_events(),
kvm_vcpu_reset() will call kvm_put_guest_fpu() without a preceding
kvm_load_guest_fpu() and corrupt the guest's FPU state (and possibly
userspace's FPU state as well).
Given that MPX is being removed from the kernel[*], fix the bug with the
simple-but-ugly approach of loading the guest's FPU during
KVM_GET_MP_STATE.
[*] See commit f240652b6032b ("x86/mpx: Remove MPX APIs").
Fixes: f775b13eedee2 ("x86,kvm: move qemu/guest FPU switching out to vcpu_run") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There exists a deadlock with range_cyclic that has existed forever. If
we loop around with a bio already built we could deadlock with a writer
who has the page locked that we're attempting to write but is waiting on
a page in our bio to be written out. The task traces are as follows
I used drgn to find the respective pages we were stuck on
page_entry.page 0xffffea00fbfc7500 index 8148 bit 15 pid 2167901
page_entry.page 0xffffea00f9bb7400 index 7680 bit 0 pid 1329874
As you can see the kworker is waiting for bit 0 (PG_locked) on index
7680, and aio-dio-invalid is waiting for bit 15 (PG_writeback) on index
8148. aio-dio-invalid has 7680, and the kworker epd looks like the
following
crash> struct extent_page_data ffffc900297bbbb0
struct extent_page_data {
bio = 0xffff889f747ed830,
tree = 0xffff889eed6ba448,
extent_locked = 0,
sync_io = 0
}
Probably worth mentioning as well that it waits for writeback of the
page to complete while holding a lock on it (at prepare_pages()).
Using drgn I walked the bio pages looking for page
0xffffea00fbfc7500 which is the one we're waiting for writeback on
bio = Object(prog, 'struct bio', address=0xffff889f747ed830)
for i in range(0, bio.bi_vcnt.value_()):
bv = bio.bi_io_vec[i]
if bv.bv_page.value_() == 0xffffea00fbfc7500:
print("FOUND IT")
which validated what I suspected.
The fix for this is simple, flush the epd before we loop back around to
the beginning of the file during writeout.
Fixes: b293f02e1423 ("Btrfs: Add writepages support") CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This fixes Spectre-v1/L1TF vulnerabilities in intel_find_fixed_event()
and intel_rdpmc_ecx_to_pmc().
kvm_rdpmc() (ancestor of intel_find_fixed_event()) and
reprogram_fixed_counter() (ancestor of intel_rdpmc_ecx_to_pmc()) are
exported symbols so KVM should treat them conservatively from a security
perspective.
Fixes: 25462f7f5295 ("KVM: x86/vPMU: Define kvm_pmu_ops to support vPMU function dispatch") Signed-off-by: Nick Finco <nifi@google.com> Signed-off-by: Marios Pomonis <pomonis@google.com> Reviewed-by: Andrew Honig <ahonig@google.com> Cc: stable@vger.kernel.org Reviewed-by: Jim Mattson <jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Changing pixel clock source without having this clock source enabled
will block the timing engine and the next operations after (in this case
setting ATMEL_HLCDC_CFG(5) settings in atmel_hlcdc_crtc_mode_set_nofb()
will fail). It is recomended (although in datasheet this is not present)
to actually enabled pixel clock source before doing any changes on timing
enginge (only SAM9X60 datasheet specifies that the peripheral clock and
pixel clock must be enabled before using LCD controller).
There is a race between adding and removing elements to the tree mod log
list and rbtree that can lead to use-after-free problems.
Consider the following example that explains how/why the problems happens:
1) Task A has mod log element with sequence number 200. It currently is
the only element in the mod log list;
2) Task A calls btrfs_put_tree_mod_seq() because it no longer needs to
access the tree mod log. When it enters the function, it initializes
'min_seq' to (u64)-1. Then it acquires the lock 'tree_mod_seq_lock'
before checking if there are other elements in the mod seq list.
Since the list it empty, 'min_seq' remains set to (u64)-1. Then it
unlocks the lock 'tree_mod_seq_lock';
3) Before task A acquires the lock 'tree_mod_log_lock', task B adds
itself to the mod seq list through btrfs_get_tree_mod_seq() and gets a
sequence number of 201;
4) Some other task, name it task C, modifies a btree and because there
elements in the mod seq list, it adds a tree mod elem to the tree
mod log rbtree. That node added to the mod log rbtree is assigned
a sequence number of 202;
5) Task B, which is doing fiemap and resolving indirect back references,
calls btrfs get_old_root(), with 'time_seq' == 201, which in turn
calls tree_mod_log_search() - the search returns the mod log node
from the rbtree with sequence number 202, created by task C;
6) Task A now acquires the lock 'tree_mod_log_lock', starts iterating
the mod log rbtree and finds the node with sequence number 202. Since
202 is less than the previously computed 'min_seq', (u64)-1, it
removes the node and frees it;
7) Task B still has a pointer to the node with sequence number 202, and
it dereferences the pointer itself and through the call to
__tree_mod_log_rewind(), resulting in a use-after-free problem.
This issue can be triggered sporadically with the test case generic/561
from fstests, and it happens more frequently with a higher number of
duperemove processes. When it happens to me, it either freezes the VM or
it produces a trace like the following before crashing:
Fix this by ensuring that btrfs_put_tree_mod_seq() computes the minimum
sequence number and iterates the rbtree while holding the lock
'tree_mod_log_lock' in write mode. Also get rid of the 'tree_mod_seq_lock'
lock, since it is now redundant.
Fixes: bd989ba359f2ac ("Btrfs: add tree modification log functions") Fixes: 097b8a7c9e48e2 ("Btrfs: join tree mod log code with the code holding back delayed refs") CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Sometimes when running generic/475 we would trip the
WARN_ON(cache->reserved) check when free'ing the block groups on umount.
This is because sometimes we don't commit the transaction because of IO
errors and thus do not cleanup the tree logs until at umount time.
These blocks are still reserved until they are cleaned up, but they
aren't cleaned up until _after_ we do the free block groups work. Fix
this by moving the free after free'ing the fs roots, that way all of the
tree logs are cleaned up and we have a properly cleaned fs. A bunch of
loops of generic/475 confirmed this fixes the problem.
CC: stable@vger.kernel.org # 4.9+ Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When using the NO_HOLES feature, if we punch a hole into a file and then
fsync it, there are cases where a subsequent fsync will miss the fact that
a hole was punched, resulting in the holes not existing after replaying
the log tree.
Essentially these cases all imply that, tree-log.c:copy_items(), is not
invoked for the leafs that delimit holes, because nothing changed those
leafs in the current transaction. And it's precisely copy_items() where
we currenly detect and log holes, which works as long as the holes are
between file extent items in the input leaf or between the beginning of
input leaf and the previous leaf or between the last item in the leaf
and the next leaf.
First example where we miss a hole:
*) The extent items of the inode span multiple leafs;
*) The punched hole covers a range that affects only the extent items of
the first leaf;
*) The fsync operation is done in full mode (BTRFS_INODE_NEEDS_FULL_SYNC
is set in the inode's runtime flags).
That results in the hole not existing after replaying the log tree.
For example, if the fs/subvolume tree has the following layout for a
particular inode:
If at transaction 11 we punch a hole coverting the range [0, 128K[, we end
up dropping the two extent items from leaf N, but we don't touch the other
leaf, so we end up in the following state:
Leaf N, generation 11:
[ ... INODE_ITEM INODE_REF ]
Leaf N + 1, generation 10:
[ EXTENT_ITEM (128K 64K) ... ]
A full fsync after punching the hole will only process leaf N because it
was modified in the current transaction, but not leaf N + 1, since it
was not modified in the current transaction (generation 10 and not 11).
As a result the fsync will not log any holes, because it didn't process
any leaf with extent items.
Second example where we will miss a hole:
*) An inode as its items spanning 5 (or more) leafs;
*) A hole is punched and it covers only the extents items of the 3rd
leaf. This resulsts in deleting the entire leaf and not touching any
of the other leafs.
So the only leaf that is modified in the current transaction, when
punching the hole, is the first leaf, which contains the inode item.
During the full fsync, the only leaf that is passed to copy_items()
is that first leaf, and that's not enough for the hole detection
code in copy_items() to determine there's a hole between the last
file extent item in the 2nd leaf and the first file extent item in
the 3rd leaf (which was the 4th leaf before punching the hole).
Fix this by scanning all leafs and punch holes as necessary when doing a
full fsync (less common than a non-full fsync) when the NO_HOLES feature
is enabled. The lack of explicit file extent items to mark holes makes it
necessary to scan existing extents to determine if holes exist.
A test case for fstests follows soon.
Fixes: 16e7549f045d33 ("Btrfs: incompatible format change to remove hole extents") CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We used to call btrfs_file_extent_inline_len() to get the uncompressed
data size of an inlined extent.
However this function is hiding evil, for compressed extent, it has no
choice but to directly read out ram_bytes from btrfs_file_extent_item.
While for uncompressed extent, it uses item size to calculate the real
data size, and ignoring ram_bytes completely.
In fact, for corrupted ram_bytes, due to above behavior kernel
btrfs_print_leaf() can't even print correct ram_bytes to expose the bug.
Since we have the tree-checker to verify all EXTENT_DATA, such mismatch
can be detected pretty easily, thus we can trust ram_bytes without the
evil btrfs_file_extent_inline_len().
Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
ext4_writepages() on an encrypted file has to encrypt the data, but it
can't modify the pagecache pages in-place, so it encrypts the data into
bounce pages and writes those instead. All bounce pages are allocated
from a mempool using GFP_NOFS.
This is not correct use of a mempool, and it can deadlock. This is
because GFP_NOFS includes __GFP_DIRECT_RECLAIM, which enables the "never
fail" mode for mempool_alloc() where a failed allocation will fall back
to waiting for one of the preallocated elements in the pool.
But since this mode is used for all a bio's pages and not just the
first, it can deadlock waiting for pages already in the bio to be freed.
This deadlock can be reproduced by patching mempool_alloc() to pretend
that pool->alloc() always fails (so that it always falls back to the
preallocations), and then creating an encrypted file of size > 128 KiB.
Fix it by only using GFP_NOFS for the first page in the bio. For
subsequent pages just use GFP_NOWAIT, and if any of those fail, just
submit the bio and start a new one.
This will need to be fixed in f2fs too, but that's less straightforward.
Fixes: c9af28fdd449 ("ext4 crypto: don't let data integrity writebacks fail with ENOMEM") Cc: stable@vger.kernel.org Signed-off-by: Eric Biggers <ebiggers@google.com> Link: https://lore.kernel.org/r/20191231181149.47619-1-ebiggers@kernel.org Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
syzbot managed to send an IPX packet through bond_alb_xmit()
and af_packet and triggered a use-after-free.
First, bond_alb_xmit() was using ipx_hdr() helper to reach
the IPX header, but ipx_hdr() was using the transport offset
instead of the network offset. In the particular syzbot
report transport offset was 0xFFFF
This patch removes ipx_hdr() since it was only (mis)used from bonding.
Then we need to make sure IPv4/IPv6/IPX headers are pulled
in skb->head before dereferencing anything.
BUG: KASAN: use-after-free in bond_alb_xmit+0x153a/0x1590 drivers/net/bonding/bond_alb.c:1452
Read of size 2 at addr ffff8801ce56dfff by task syz-executor.2/18108
(if (ipx_hdr(skb)->ipx_checksum != IPX_NO_CHECKSUM) ...)
GEM_MAX_TX_LEN currently resolves to 0x3FF8 for any IP version supporting
TSO with full 14bits of length field in payload descriptor. But an IP
errata causes false amba_error (bit 6 of ISR) when length in payload
descriptors is specified above 16387. The error occurs because the DMA
falsely concludes that there is not enough space in SRAM for incoming
payload. These errors were observed continuously under stress of large
packets using iperf on a version where SRAM was 16K for each queue. This
errata will be documented shortly and affects all versions since TSO
functionality was added. Hence limit the max length to 0x3FC0 (rounded).
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The IP TSO implementation does NOT require the length to be a
multiple of 8. That is only a requirement for UFO as per IP
documentation. Hence, exit macb_features_check function in the
beginning if the protocol is not UDP. Only when it is UDP,
proceed further to the alignment checks. Update comments to
reflect the same. Also remove dead code checking for protocol
TCP when calculating header length.
Fixes: 1629dd4f763c ("cadence: Add LSO support.") Signed-off-by: Harini Katakam <harini.katakam@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
After a number of suspend and resume cycles, it is possible for the RBUF
to be stuck in Wake-on-LAN mode, despite the MPD enable bit being
cleared which instructed the RBUF to exit that mode.
Avoid creating that problematic condition by clearing the RX_EN and
TX_EN bits in the UniMAC prior to disable the Magic Packet Detector
logic which is guaranteed to make the RBUF exit Wake-on-LAN mode.
Fixes: 83e82f4c706b ("net: systemport: add Wake-on-LAN support") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Jakub noticed there is a potential resource leak in
tcindex_set_parms(): when tcindex_filter_result_init() fails
and it jumps to 'errout1' which doesn't release the memory
and resources allocated by tcindex_alloc_perfect_hash().
We should just jump to 'errout_alloc' which calls
tcindex_free_perfect_hash().
Fixes: b9a24bb76bf6 ("net_sched: properly handle failure case of tcf_exts_init()") Reported-by: Jakub Kicinski <kuba@kernel.org> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The 7445 switch clocking profiles do not allow us to run the IMP port at
2Gb/sec in a way that it is reliable and consistent. Make sure that the
setting is only applied to the 7278 family.
Fixes: 8f1880cbe8d0 ("net: dsa: bcm_sf2: Configure IMP port for 2Gb/sec") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The watchdog driver compatible is "dlg,da9062-watchdog" and not
"dlg,da9062-wdt". Therefore the mfd-core can't populate the of_node and
fwnode. As result the watchdog driver can't parse the devicetree.
Fixes: 9b40b030c4ad ("mfd: da9062: Supply core driver") Signed-off-by: Marco Felsch <m.felsch@pengutronix.de> Acked-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
set_seen() sets the bit corresponding to the PEB number in the bitmap,
so when self_check_seen() wants to find PEBs that haven't been seen we
have to print the PEBs that have their bit cleared, not the ones which
have it set.
Fixes: 5d71afb00840 ("ubi: Use bitmaps in Fastmap self-check code") Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The nfsd4_blocked_lock->nbl_time timestamp is recorded in jiffies,
but then compared to a CLOCK_REALTIME timestamp later on, which makes
no sense.
For consistency with the other timestamps, change this to use a time_t.
This is a change in behavior, which may cause regressions, but the
current code is not sensible. On a system with CONFIG_HZ=1000,
the 'time_after((unsigned long)nbl->nbl_time, (unsigned long)cutoff))'
check is false for roughly the first 18 days of uptime and then true
for the next 49 days.
Fixes: 7919d0a27f1e ("nfsd: add a LRU list for blocked locks") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The nfsd4_cb_layout_done() function takes a 'time_t' value,
multiplied by NSEC_PER_SEC*2 to get a nanosecond value.
This works fine on 64-bit architectures, but on 32-bit, any
value over 1 second results in a signed integer overflow
with unexpected results.
Cast one input to a 64-bit type in order to produce the
same result that we have on 64-bit architectures, regarless
of the type of nfsd4_lease.
Fixes: 6b9b21073d3b ("nfsd: give up on CB_LAYOUTRECALLs after two lease periods") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The nr_pages argument of get_user_pages_remote() should always be in terms
of the system page size, not the MR page size. Use PAGE_SIZE instead of
umem_odp->page_shift.
Commit b0ffeb537f3a ("IB/mlx5: Fix iteration overrun in GSI qps") changed
the way outstanding WRs are tracked for the GSI QP. But the fix did not
cover the case when a call to ib_post_send() fails and updates index to
track outstanding.
Since the prior commmit outstanding_pi should not be bounded otherwise the
loop generate_completions() will fail.
Fixes: b0ffeb537f3a ("IB/mlx5: Fix iteration overrun in GSI qps") Link: https://lore.kernel.org/r/1576195889-23527-1-git-send-email-psajeepa@purestorage.com Signed-off-by: Prabhath Sajeepa <psajeepa@purestorage.com> Acked-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
../drivers/net/ethernet/dec/tulip/uli526x.c:1812:3: warning: misleading
indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
switch (mode) {
^
../drivers/net/ethernet/dec/tulip/uli526x.c:1809:2: note: previous
statement is here
if (cr6set)
^
1 warning generated.
../drivers/net/ethernet/dec/tulip/dmfe.c:2217:3: warning: misleading
indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
switch(mode) {
^
../drivers/net/ethernet/dec/tulip/dmfe.c:2214:2: note: previous
statement is here
if (cr6set)
^
1 warning generated.
This warning occurs because there is a space before the tab on these
lines. Remove them so that the indentation is consistent with the Linux
kernel coding style and clang no longer warns.
While we are here, adjust the default block in dmfe_init_module to have
a proper break between the label and assignment and add a space between
the switch and opening parentheses to avoid a checkpatch warning.
Fixes: e1c3e5014040 ("[PATCH] initialisation cleanup for ULI526x-net-driver") Link: https://github.com/ClangBuiltLinux/linux/issues/795 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
../drivers/net/ethernet/smsc/smc911x.c:939:3: warning: misleading
indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
if (!lp->ctl_rfduplx)
^
../drivers/net/ethernet/smsc/smc911x.c:936:2: note: previous statement
is here
if (lp->ctl_rspeed != 100)
^
1 warning generated.
This warning occurs because there is a space after the tab on this line.
Remove it so that the indentation is consistent with the Linux kernel
coding style and clang no longer warns.
Fixes: 0a0c72c9118c ("[PATCH] RE: [PATCH 1/1] net driver: Add support for SMSC LAN911x line of ethernet chips") Link: https://github.com/ClangBuiltLinux/linux/issues/796 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
../drivers/net/ppp/ppp_async.c:877:6: warning: misleading indentation;
statement is not part of the previous 'if' [-Wmisleading-indentation]
ap->rpkt = skb;
^
../drivers/net/ppp/ppp_async.c:875:5: note: previous statement is here
if (!skb)
^
1 warning generated.
This warning occurs because there is a space before the tab on this
line. Clean up this entire block's indentation so that it is consistent
with the Linux kernel coding style and clang no longer warns.
Fixes: 6722e78c9005 ("[PPP]: handle misaligned accesses") Link: https://github.com/ClangBuiltLinux/linux/issues/800 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
../drivers/nfc/pn544/pn544.c:696:4: warning: misleading indentation;
statement is not part of the previous 'if' [-Wmisleading-indentation]
return nfc_hci_send_cmd(hdev, NFC_HCI_RF_READER_A_GATE,
^
../drivers/nfc/pn544/pn544.c:692:3: note: previous statement is here
if (target->nfcid1_len != 4 && target->nfcid1_len != 7 &&
^
1 warning generated.
This warning occurs because there is a space after the tab on this line.
Remove it so that the indentation is consistent with the Linux kernel
coding style and clang no longer warns.
Fixes: da052850b911 ("NFC: Add pn544 presence check for different targets") Link: https://github.com/ClangBuiltLinux/linux/issues/814 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
../arch/powerpc/boot/4xx.c:231:3: warning: misleading indentation;
statement is not part of the previous 'else' [-Wmisleading-indentation]
val = SDRAM0_READ(DDR0_42);
^
../arch/powerpc/boot/4xx.c:227:2: note: previous statement is here
else
^
This is because there is a space at the beginning of this line; remove
it so that the indentation is consistent according to the Linux kernel
coding style and clang no longer warns.
Fixes: d23f5099297c ("[POWERPC] 4xx: Adds decoding of 440SPE memory size to boot wrapper library") Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://github.com/ClangBuiltLinux/linux/issues/780 Link: https://lore.kernel.org/r/20191209200338.12546-1-natechancellor@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
../fs/ext2/super.c:1076:3: warning: misleading indentation; statement is
not part of the previous 'if' [-Wmisleading-indentation]
sbi->s_groups_count = ((le32_to_cpu(es->s_blocks_count) -
^
../fs/ext2/super.c:1074:2: note: previous statement is here
if (EXT2_BLOCKS_PER_GROUP(sb) == 0)
^
1 warning generated.
This warning occurs because there is a space before the tab on this
line. Remove it so that the indentation is consistent with the Linux
kernel coding style and clang no longer warns.
../drivers/phy/qualcomm/phy-qcom-apq8064-sata.c:83:4: warning:
misleading indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
usleep_range(DELAY_INTERVAL_US, DELAY_INTERVAL_US + 50);
^
../drivers/phy/qualcomm/phy-qcom-apq8064-sata.c:80:3: note: previous
statement is here
if (readl_relaxed(addr) & mask)
^
1 warning generated.
This warning occurs because there is a space after the tab on this line.
Remove it so that the indentation is consistent with the Linux kernel
coding style and clang no longer warns.
Fixes: 1de990d8a169 ("phy: qcom: Add driver for QCOM APQ8064 SATA PHY") Link: https://github.com/ClangBuiltLinux/linux/issues/816 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
../drivers/scsi/qla4xxx/ql4_os.c:4148:3: warning: misleading
indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
if (ha->fw_dump)
^
../drivers/scsi/qla4xxx/ql4_os.c:4144:2: note: previous statement is
here
if (ha->queues)
^
1 warning generated.
This warning occurs because there is a space after the tab on this
line. Remove it so that the indentation is consistent with the Linux
kernel coding style and clang no longer warns.
Fixes: 068237c87c64 ("[SCSI] qla4xxx: Capture minidump for ISP82XX on firmware failure") Link: https://github.com/ClangBuiltLinux/linux/issues/819 Link: https://lore.kernel.org/r/20191218015252.20890-1-natechancellor@gmail.com Acked-by: Manish Rangankar <mrangankar@marvell.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
../drivers/scsi/csiostor/csio_scsi.c:1386:3: warning: misleading
indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
csio_lnodes_exit(hw, 1);
^
../drivers/scsi/csiostor/csio_scsi.c:1382:2: note: previous statement is
here
if (*buf != '1')
^
1 warning generated.
This warning occurs because there is a space after the tab on this
line. Remove it so that the indentation is consistent with the Linux
kernel coding style and clang no longer warns.
Since qla82xx_get_fw_size() returns a number in CPU-endian format, change
its return type from __le32 into u32. This patch does not change any
functionality.
Fixes: 9c2b297572bf ("[SCSI] qla2xxx: Support for loading Unified ROM Image (URI) format firmware file.") Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Quinn Tran <qutran@marvell.com> Cc: Martin Wilck <mwilck@suse.com> Cc: Daniel Wagner <dwagner@suse.de> Cc: Roman Bolshakov <r.bolshakov@yadro.com> Link: https://lore.kernel.org/r/20191219004905.39586-1-bvanassche@acm.org Reviewed-by: Daniel Wagner <dwagner@suse.de> Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For a little over a year, U-Boot on Tegra124 has configured the flow
controller to perform automatic RAM re-repair on off->on power
transitions of the CPU rail[1]. This is mandatory for correct operation
of Tegra124. However, RAM re-repair relies on certain clocks, which the
kernel must enable and leave running. The fuse clock is one of those
clocks. Mark this clock as critical so that LP1 power mode (system
suspend) operates correctly.
Free the vCPU's wbinvd_dirty_mask if vCPU creation fails after
kvm_arch_vcpu_init(), e.g. when installing the vCPU's file descriptor.
Do the freeing by calling kvm_arch_vcpu_free() instead of open coding
the freeing. This adds a likely superfluous, but ultimately harmless,
call to kvmclock_reset(), which only clears vcpu->arch.pv_time_enabled.
Using kvm_arch_vcpu_free() allows for additional cleanup in the future.
Fixes: f5f48ee15c2ee ("KVM: VMX: Execute WBINVD to keep data consistency with assigned devices") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Explicitly free the shared page if kvmppc_mmu_init() fails during
kvmppc_core_vcpu_create(), as the page is freed only in
kvmppc_core_vcpu_free(), which is not reached via kvm_vcpu_uninit().
Fixes: 96bc451a15329 ("KVM: PPC: Introduce shared page") Cc: stable@vger.kernel.org Reviewed-by: Greg Kurz <groug@kaod.org> Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Acked-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This fixes a Spectre-v1/L1TF vulnerability in fixed_msr_to_seg_unit().
This function contains index computations based on the
(attacker-controlled) MSR number.
Fixes: de9aef5e1ad6 ("KVM: MTRR: introduce fixed_mtrr_segment table") Signed-off-by: Nick Finco <nifi@google.com> Signed-off-by: Marios Pomonis <pomonis@google.com> Reviewed-by: Andrew Honig <ahonig@google.com> Cc: stable@vger.kernel.org Reviewed-by: Jim Mattson <jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This fixes a Spectre-v1/L1TF vulnerability in x86_decode_insn().
kvm_emulate_instruction() (an ancestor of x86_decode_insn()) is an exported
symbol, so KVM should treat it conservatively from a security perspective.
Fixes: 045a282ca415 ("KVM: emulator: implement fninit, fnstsw, fnstcw") Signed-off-by: Nick Finco <nifi@google.com> Signed-off-by: Marios Pomonis <pomonis@google.com> Reviewed-by: Andrew Honig <ahonig@google.com> Cc: stable@vger.kernel.org Reviewed-by: Jim Mattson <jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This fixes a Spectre-v1/L1TF vulnerability in set_msr_mce() and
get_msr_mce().
Both functions contain index computations based on the
(attacker-controlled) MSR number.
Fixes: 890ca9aefa78 ("KVM: Add MCE support") Signed-off-by: Nick Finco <nifi@google.com> Signed-off-by: Marios Pomonis <pomonis@google.com> Reviewed-by: Andrew Honig <ahonig@google.com> Cc: stable@vger.kernel.org Reviewed-by: Jim Mattson <jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This fixes a Spectre-v1/L1TF vulnerability in ioapic_read_indirect().
This function contains index computations based on the
(attacker-controlled) IOREGSEL register.
Fixes: a2c118bfab8b ("KVM: Fix bounds checking in ioapic indirect register reads (CVE-2013-1798)") Signed-off-by: Nick Finco <nifi@google.com> Signed-off-by: Marios Pomonis <pomonis@google.com> Reviewed-by: Andrew Honig <ahonig@google.com> Cc: stable@vger.kernel.org Reviewed-by: Jim Mattson <jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This fixes a Spectre-v1/L1TF vulnerability in the get_gp_pmc() and
get_fixed_pmc() functions.
They both contain index computations based on the (attacker-controlled)
MSR number.
Fixes: 25462f7f5295 ("KVM: x86/vPMU: Define kvm_pmu_ops to support vPMU function dispatch") Signed-off-by: Nick Finco <nifi@google.com> Signed-off-by: Marios Pomonis <pomonis@google.com> Reviewed-by: Andrew Honig <ahonig@google.com> Cc: stable@vger.kernel.org Reviewed-by: Jim Mattson <jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This fixes a Spectre-v1/L1TF vulnerability in ioapic_write_indirect().
This function contains index computations based on the
(attacker-controlled) IOREGSEL register.
This patch depends on patch
"KVM: x86: Protect ioapic_read_indirect() from Spectre-v1/L1TF attacks".
Fixes: 70f93dae32ac ("KVM: Use temporary variable to shorten lines.") Signed-off-by: Nick Finco <nifi@google.com> Signed-off-by: Marios Pomonis <pomonis@google.com> Reviewed-by: Andrew Honig <ahonig@google.com> Cc: stable@vger.kernel.org Reviewed-by: Jim Mattson <jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This fixes Spectre-v1/L1TF vulnerabilities in kvm_hv_msr_get_crash_data()
and kvm_hv_msr_set_crash_data().
These functions contain index computations that use the
(attacker-controlled) MSR number.
Fixes: e7d9513b60e8 ("kvm/x86: added hyper-v crash msrs into kvm hyperv context") Signed-off-by: Nick Finco <nifi@google.com> Signed-off-by: Marios Pomonis <pomonis@google.com> Reviewed-by: Andrew Honig <ahonig@google.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This fixes a Spectre-v1/L1TF vulnerability in kvm_lapic_reg_write().
This function contains index computations based on the
(attacker-controlled) MSR number.
Fixes: 0105d1a52640 ("KVM: x2apic interface to lapic") Signed-off-by: Nick Finco <nifi@google.com> Signed-off-by: Marios Pomonis <pomonis@google.com> Reviewed-by: Andrew Honig <ahonig@google.com> Cc: stable@vger.kernel.org Reviewed-by: Jim Mattson <jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This fixes a Spectre-v1/L1TF vulnerability in __kvm_set_dr() and
kvm_get_dr().
Both kvm_get_dr() and kvm_set_dr() (a wrapper of __kvm_set_dr()) are
exported symbols so KVM should tream them conservatively from a security
perspective.
Fixes: 020df0794f57 ("KVM: move DR register access handling into generic code") Signed-off-by: Nick Finco <nifi@google.com> Signed-off-by: Marios Pomonis <pomonis@google.com> Reviewed-by: Andrew Honig <ahonig@google.com> Cc: stable@vger.kernel.org Reviewed-by: Jim Mattson <jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This fixes Spectre-v1/L1TF vulnerabilities in
vmx_read_guest_seg_selector(), vmx_read_guest_seg_base(),
vmx_read_guest_seg_limit() and vmx_read_guest_seg_ar(). When
invoked from emulation, these functions contain index computations
based on the (attacker-influenced) segment value. Using constants
prevents the attack.
Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This fixes a Spectre-v1/L1TF vulnerability in picdev_write().
It replaces index computations based on the (attacked-controlled) port
number with constants through a minor refactoring.
Fixes: 85f455f7ddbe ("KVM: Add support for in-kernel PIC emulation") Signed-off-by: Nick Finco <nifi@google.com> Signed-off-by: Marios Pomonis <pomonis@google.com> Reviewed-by: Andrew Honig <ahonig@google.com> Cc: stable@vger.kernel.org Reviewed-by: Jim Mattson <jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 3aa6c19d2f38be ("xen/balloon: Support xend-based toolstack")
tried to fix a regression with running on rather ancient Xen versions.
Unfortunately the fix was based on the assumption that xend would
just use another Xenstore node, but in reality only some downstream
versions of xend are doing that. The upstream xend does not write
that Xenstore node at all, so the problem must be fixed in another
way.
The easiest way to achieve that is to fall back to the behavior
before commit 96edd61dcf4436 ("xen/balloon: don't online new memory
initially") in case the static memory maximum can't be read.
This is achieved by setting static_max to the current number of
memory pages known by the system resulting in target_diff becoming
zero.
Fixes: 3aa6c19d2f38be ("xen/balloon: Support xend-based toolstack") Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: <stable@vger.kernel.org> # 4.13 Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The filter name is fixed to "exit_reason" for some kvm_exit events, no
matter what architect we have. Actually, the filter name ("exit_reason")
is only applicable to x86, meaning it's broken on other architects
including aarch64.
This fixes the issue by providing various kvm_exit filter names, depending
on architect we're on. Afterwards, the variable filter name is picked and
applied through ioctl(fd, SET_FILTER).
Reported-by: Andrew Jones <drjones@redhat.com> Signed-off-by: Gavin Shan <gshan@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When upcalling gssproxy, cache_head.expiry_time is set as a
timeval, not seconds since boot. As such, RPC cache expiry
logic will not clean expired objects created under
auth.rpcsec.context cache.
This has proven to cause kernel memory leaks on field. Using
64 bit variants of getboottime/timespec
Expiration times have worked this way since 2010's c5b29f885afe "sunrpc:
use seconds since boot in expiry cache". The gssproxy code introduced
in 2012 added gss_proxy_save_rsc and introduced the bug. That's a while
for this to lurk, but it required a bit of an extreme case to make it
obvious.
Signed-off-by: Roberto Bergantinos Corpas <rbergant@redhat.com> Cc: stable@vger.kernel.org Fixes: 030d794bf498 "SUNRPC: Use gssproxy upcall for server..." Tested-By: Frank Sorenson <sorenson@redhat.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The IGTK keys are only removed by mac80211 after it has already
removed the AP station. This causes the driver to throw an error
because mac80211 is trying to remove the IGTK when the station doesn't
exist anymore.
The firmware is aware that the station has been removed and can deal
with it the next time we try to add an IGTK for a station, so we
shouldn't try to remove the key if the station ID is
IWL_MVM_INVALID_STA. Do this by removing the check for mvm_sta before
calling iwl_mvm_send_sta_igtk() and check return from that function
gracefully if the station ID is invalid.
Cc: stable@vger.kernel.org # 4.12+ Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For a little over a year, U-Boot has configured the flow controller to
perform automatic RAM re-repair on off->on power transitions of the CPU
rail[1]. This is mandatory for correct operation of Tegra124. However,
RAM re-repair relies on certain clocks, which the kernel must enable and
leave running. PLLP is one of those clocks. This clock is shut down
during LP1 in order to save power. Enable bypass (which I believe routes
osc_div_clk, essentially the crystal clock, to the PLL output) so that
this clock signal toggles even though the PLL is not active. This is
required so that LP1 power mode (system suspend) operates correctly.
The bypass configuration must then be undone when resuming from LP1, so
that all peripheral clocks run at the expected rate. Without this, many
peripherals won't work correctly; for example, the UART baud rate would
be incorrect.
NVIDIA's downstream kernel code only does this if not compiled for
Tegra30, so the added code is made conditional upon the chip ID.
NVIDIA's downstream code makes this change conditional upon the active
CPU cluster. The upstream kernel currently doesn't support cluster
switching, so this patch doesn't test the active CPU cluster ID.
If we abort a transaction we have the following sequence
if (!trans->dirty && list_empty(&trans->new_bgs))
return;
WRITE_ONCE(trans->transaction->aborted, err);
The idea being if we didn't modify anything with our trans handle then
we don't really need to abort the whole transaction, maybe the other
trans handles are fine and we can carry on.
However in the case of create_snapshot we add a pending_snapshot object
to our transaction and then commit the transaction. We don't actually
modify anything. sync() behaves the same way, attach to an existing
transaction and commit it. This means that if we have an IO error in
the right places we could abort the committing transaction with our
trans->dirty being not set and thus not set transaction->aborted.
This is a problem because in the create_snapshot() case we depend on
pending->error being set to something, or btrfs_commit_transaction
returning an error.
If we are not the trans handle that gets to commit the transaction, and
we're waiting on the commit to happen we get our return value from
cur_trans->aborted. If this was not set to anything because sync() hit
an error in the transaction commit before it could modify anything then
cur_trans->aborted would be 0. Thus we'd return 0 from
btrfs_commit_transaction() in create_snapshot.
This is a problem because we then try to do things with
pending_snapshot->snap, which will be NULL because we didn't create the
snapshot, and then we'll get a NULL pointer dereference like the
following
In order to fix this we need to make sure anybody who calls
commit_transaction has trans->dirty set so that they properly set the
trans->transaction->aborted value properly so any waiters know bad
things happened.
This was found while I was running generic/475 with my modified
fsstress, it reproduced within a few runs. I ran with this patch all
night and didn't see the problem again.
CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When a NFS directory page cache page is removed from the page cache,
its contents are freed through a call to nfs_readdir_clear_array().
To prevent the removal of the page cache entry until after we've
finished reading it, we must take the page lock.
Fixes: 11de3b11e08c ("NFS: Fix a memory leak in nfs_readdir") Cc: stable@vger.kernel.org # v2.6.37+ Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Reviewed-by: Benjamin Coddington <bcodding@redhat.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
nfs_readdir_xdr_to_array() must not exit without having initialised
the array, so that the page cache deletion routines can safely
call nfs_readdir_clear_array().
Furthermore, we should ensure that if we exit nfs_readdir_filler()
with an error, we free up any page contents to prevent a leak
if we try to fill the page again.
Fixes: 11de3b11e08c ("NFS: Fix a memory leak in nfs_readdir") Cc: stable@vger.kernel.org # v2.6.37+ Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Reviewed-by: Benjamin Coddington <bcodding@redhat.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On certain cases when response length is less than 32, NVME response data
is supplied inline in IOCB. This is indicated by some combination of state
flags. There was an instance when a high, and incorrect, response length
was indicated causing driver to overrun buffers. Fix this by checking and
limiting the response payload length.
The function crypto_spawn_alg is racy because it drops the lock
before shooting the dying algorithm. The algorithm could disappear
altogether before we shoot it.
This patch fixes it by moving the shooting into the locked section.
AMD Seattle incorporates a non-PCI version of the v3 CCP crypto
accelerator, and this version was left behind when the maximum
RSA modulus size was parameterized in order to support v5 hardware
which supports larger moduli than v3 hardware does. Due to this
oversight, RSA acceleration no longer works at all on these systems.
Fix this by setting the .rsamax property to the appropriate value
for v3 platform hardware.
Fixes: e28c190db66830c0 ("csrypto: ccp - Expand RSA support for a v5 ccp") Cc: Gary R Hook <gary.hook@amd.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Acked-by: Gary R Hook <gary.hook@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The 'clean' rule in the samples/bpf Makefile tries to remove backup
files (ending in ~). However, if no such files exist, it will instead try
to remove the user's home directory. While the attempt is mostly harmless,
it does lead to a somewhat scary warning like this:
rm: cannot remove '~': Is a directory
Fix this by using find instead of shell expansion to locate any actual
backup files that need to be removed.
Fixes: b62a796c109c ("samples/bpf: allow make to be run from samples/bpf/ directory") Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Link: https://lore.kernel.org/bpf/157952560126.1683545.7273054725976032511.stgit@toke.dk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
As function_graph tracer can run when RCU is not "watching", it can not be
protected by synchronize_rcu() it requires running a task on each CPU before
it can be freed. Calling schedule_on_each_cpu(ftrace_sync) needs to be used.
Link: https://lore.kernel.org/r/20200205131110.GT2935@paulmck-ThinkPad-P72 Cc: stable@vger.kernel.org Fixes: b9b0c831bed26 ("ftrace: Convert graph filter to use hash tables") Reported-by: "Paul E. McKenney" <paulmck@kernel.org> Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Because the function graph tracer can execute in sections where RCU is not
"watching", the rcu_dereference_sched() for the has needs to be open coded.
This is fine because the RCU "flavor" of the ftrace hash is protected by
its own RCU handling (it does its own little synchronization on every CPU
and does not rely on RCU sched).
Acked-by: Joel Fernandes (Google) <joel@joelfernandes.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Fix following instances of sparse error
kernel/trace/ftrace.c:5667:29: error: incompatible types in comparison
kernel/trace/ftrace.c:5813:21: error: incompatible types in comparison
kernel/trace/ftrace.c:5868:36: error: incompatible types in comparison
kernel/trace/ftrace.c:5870:25: error: incompatible types in comparison
Use rcu_dereference_protected to dereference the newly annotated pointer.
Fix following instances of sparse error
kernel/trace/ftrace.c:5664:29: error: incompatible types in comparison
kernel/trace/ftrace.c:5785:21: error: incompatible types in comparison
kernel/trace/ftrace.c:5864:36: error: incompatible types in comparison
kernel/trace/ftrace.c:5866:25: error: incompatible types in comparison
Use rcu_dereference_protected to access the __rcu annotated pointer.
Link: http://lkml.kernel.org/r/20200201072703.17330-1-frextrite@gmail.com Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org> Signed-off-by: Amol Grover <frextrite@gmail.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If benbi IV is used in AEAD construction, for example:
cryptsetup luksFormat <device> --cipher twofish-xts-benbi --key-size 512 --integrity=hmac-sha256
the constructor uses wrong skcipher function and crashes:
The space-maps track the reference counts for disk blocks allocated by
both the thin-provisioning and cache targets. There are variants for
tracking metadata blocks and data blocks.
Transactionality is implemented by never touching blocks from the
previous transaction, so we can rollback in the event of a crash.
When allocating a new block we need to ensure the block is free (has
reference count of 0) in both the current and previous transaction.
Prior to this fix we were doing this by searching for a free block in
the previous transaction, and relying on a 'begin' counter to track
where the last allocation in the current transaction was. This
'begin' field was not being updated in all code paths (eg, increment
of a data block reference count due to breaking sharing of a neighbour
block in the same btree leaf).
This fix keeps the 'begin' field, but now it's just a hint to speed up
the search. Instead the current transaction is searched for a free
block, and then the old transaction is double checked to ensure it's
free. Much simpler.
This fixes reports of sm_disk_new_block()'s BUG_ON() triggering when
DM thin-provisioning's snapshots are heavily used.
Reported-by: Eric Wheeler <dm-devel@lists.ewheeler.net> Cc: stable@vger.kernel.org Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
projects / mirror_ubuntu-bionic-kernel.git / log