]>
Commit | Line | Data |
---|---|---|
7c673cae FG |
1 | /******************************************************************************* |
2 | ||
3 | Copyright (c) 2001-2015, Intel Corporation | |
4 | All rights reserved. | |
5 | ||
6 | Redistribution and use in source and binary forms, with or without | |
7 | modification, are permitted provided that the following conditions are met: | |
8 | ||
9 | 1. Redistributions of source code must retain the above copyright notice, | |
10 | this list of conditions and the following disclaimer. | |
11 | ||
12 | 2. Redistributions in binary form must reproduce the above copyright | |
13 | notice, this list of conditions and the following disclaimer in the | |
14 | documentation and/or other materials provided with the distribution. | |
15 | ||
16 | 3. Neither the name of the Intel Corporation nor the names of its | |
17 | contributors may be used to endorse or promote products derived from | |
18 | this software without specific prior written permission. | |
19 | ||
20 | THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" | |
21 | AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE | |
22 | IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE | |
23 | ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE | |
24 | LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR | |
25 | CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF | |
26 | SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS | |
27 | INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN | |
28 | CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) | |
29 | ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE | |
30 | POSSIBILITY OF SUCH DAMAGE. | |
31 | ||
32 | ***************************************************************************/ | |
33 | ||
34 | #ifndef _E1000_ICH8LAN_H_ | |
35 | #define _E1000_ICH8LAN_H_ | |
36 | ||
37 | #define ICH_FLASH_GFPREG 0x0000 | |
38 | #define ICH_FLASH_HSFSTS 0x0004 | |
39 | #define ICH_FLASH_HSFCTL 0x0006 | |
40 | #define ICH_FLASH_FADDR 0x0008 | |
41 | #define ICH_FLASH_FDATA0 0x0010 | |
42 | ||
43 | /* Requires up to 10 seconds when MNG might be accessing part. */ | |
44 | #define ICH_FLASH_READ_COMMAND_TIMEOUT 10000000 | |
45 | #define ICH_FLASH_WRITE_COMMAND_TIMEOUT 10000000 | |
46 | #define ICH_FLASH_ERASE_COMMAND_TIMEOUT 10000000 | |
47 | #define ICH_FLASH_LINEAR_ADDR_MASK 0x00FFFFFF | |
48 | #define ICH_FLASH_CYCLE_REPEAT_COUNT 10 | |
49 | ||
50 | #define ICH_CYCLE_READ 0 | |
51 | #define ICH_CYCLE_WRITE 2 | |
52 | #define ICH_CYCLE_ERASE 3 | |
53 | ||
54 | #define FLASH_GFPREG_BASE_MASK 0x1FFF | |
55 | #define FLASH_SECTOR_ADDR_SHIFT 12 | |
56 | ||
57 | #define ICH_FLASH_SEG_SIZE_256 256 | |
58 | #define ICH_FLASH_SEG_SIZE_4K 4096 | |
59 | #define ICH_FLASH_SEG_SIZE_8K 8192 | |
60 | #define ICH_FLASH_SEG_SIZE_64K 65536 | |
61 | ||
62 | #define E1000_ICH_FWSM_RSPCIPHY 0x00000040 /* Reset PHY on PCI Reset */ | |
63 | /* FW established a valid mode */ | |
64 | #define E1000_ICH_FWSM_FW_VALID 0x00008000 | |
65 | #define E1000_ICH_FWSM_PCIM2PCI 0x01000000 /* ME PCIm-to-PCI active */ | |
66 | #define E1000_ICH_FWSM_PCIM2PCI_COUNT 2000 | |
67 | ||
68 | #define E1000_ICH_MNG_IAMT_MODE 0x2 | |
69 | ||
70 | #define E1000_FWSM_WLOCK_MAC_MASK 0x0380 | |
71 | #define E1000_FWSM_WLOCK_MAC_SHIFT 7 | |
72 | #if !defined(EXTERNAL_RELEASE) || defined(ULP_SUPPORT) | |
73 | #define E1000_FWSM_ULP_CFG_DONE 0x00000400 /* Low power cfg done */ | |
74 | #endif /* !EXTERNAL_RELEASE || ULP_SUPPORT */ | |
75 | ||
76 | /* Shared Receive Address Registers */ | |
77 | #define E1000_SHRAL_PCH_LPT(_i) (0x05408 + ((_i) * 8)) | |
78 | #define E1000_SHRAH_PCH_LPT(_i) (0x0540C + ((_i) * 8)) | |
79 | ||
80 | #if !defined(EXTERNAL_RELEASE) || defined(ULP_SUPPORT) | |
81 | #define E1000_H2ME 0x05B50 /* Host to ME */ | |
82 | #endif /* !EXTERNAL_RELEASE || ULP_SUPPORT */ | |
83 | #if !defined(EXTERNAL_RELEASE) || defined(ULP_SUPPORT) | |
84 | #define E1000_H2ME_ULP 0x00000800 /* ULP Indication Bit */ | |
85 | #define E1000_H2ME_ENFORCE_SETTINGS 0x00001000 /* Enforce Settings */ | |
86 | ||
87 | #endif /* !EXTERNAL_RELEASE || ULP_SUPPORT */ | |
88 | #define ID_LED_DEFAULT_ICH8LAN ((ID_LED_DEF1_DEF2 << 12) | \ | |
89 | (ID_LED_OFF1_OFF2 << 8) | \ | |
90 | (ID_LED_OFF1_ON2 << 4) | \ | |
91 | (ID_LED_DEF1_DEF2)) | |
92 | ||
93 | #define E1000_ICH_NVM_SIG_WORD 0x13 | |
94 | #define E1000_ICH_NVM_SIG_MASK 0xC000 | |
95 | #define E1000_ICH_NVM_VALID_SIG_MASK 0xC0 | |
96 | #define E1000_ICH_NVM_SIG_VALUE 0x80 | |
97 | ||
98 | #define E1000_ICH8_LAN_INIT_TIMEOUT 1500 | |
99 | ||
100 | #if !defined(EXTERNAL_RELEASE) || defined(ULP_SUPPORT) | |
101 | /* FEXT register bit definition */ | |
102 | #define E1000_FEXT_PHY_CABLE_DISCONNECTED 0x00000004 | |
103 | ||
104 | #endif /* !EXTERNAL_RELEASE || ULP_SUPPORT */ | |
105 | #define E1000_FEXTNVM_SW_CONFIG 1 | |
106 | #define E1000_FEXTNVM_SW_CONFIG_ICH8M (1 << 27) /* different on ICH8M */ | |
107 | ||
108 | #define E1000_FEXTNVM3_PHY_CFG_COUNTER_MASK 0x0C000000 | |
109 | #define E1000_FEXTNVM3_PHY_CFG_COUNTER_50MSEC 0x08000000 | |
110 | ||
111 | #define E1000_FEXTNVM4_BEACON_DURATION_MASK 0x7 | |
112 | #define E1000_FEXTNVM4_BEACON_DURATION_8USEC 0x7 | |
113 | #define E1000_FEXTNVM4_BEACON_DURATION_16USEC 0x3 | |
114 | ||
115 | #define E1000_FEXTNVM6_REQ_PLL_CLK 0x00000100 | |
116 | #define E1000_FEXTNVM6_ENABLE_K1_ENTRY_CONDITION 0x00000200 | |
117 | #define E1000_FEXTNVM6_K1_OFF_ENABLE 0x80000000 | |
118 | /* bit for disabling packet buffer read */ | |
119 | #define E1000_FEXTNVM7_DISABLE_PB_READ 0x00040000 | |
120 | #define E1000_FEXTNVM7_SIDE_CLK_UNGATE 0x00000004 | |
121 | #if !defined(EXTERNAL_RELEASE) || defined(ULP_SUPPORT) | |
122 | #define E1000_FEXTNVM7_DISABLE_SMB_PERST 0x00000020 | |
123 | #endif /* !EXTERNAL_RELEASE || ULP_SUPPORT */ | |
124 | #define PCIE_ICH8_SNOOP_ALL PCIE_NO_SNOOP_ALL | |
125 | ||
126 | #define E1000_ICH_RAR_ENTRIES 7 | |
127 | #define E1000_PCH2_RAR_ENTRIES 5 /* RAR[0], SHRA[0-3] */ | |
128 | #define E1000_PCH_LPT_RAR_ENTRIES 12 /* RAR[0], SHRA[0-10] */ | |
129 | ||
130 | #define PHY_PAGE_SHIFT 5 | |
131 | #define PHY_REG(page, reg) (((page) << PHY_PAGE_SHIFT) | \ | |
132 | ((reg) & MAX_PHY_REG_ADDRESS)) | |
133 | #define IGP3_KMRN_DIAG PHY_REG(770, 19) /* KMRN Diagnostic */ | |
134 | #define IGP3_VR_CTRL PHY_REG(776, 18) /* Voltage Regulator Control */ | |
135 | ||
136 | #define IGP3_KMRN_DIAG_PCS_LOCK_LOSS 0x0002 | |
137 | #define IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK 0x0300 | |
138 | #define IGP3_VR_CTRL_MODE_SHUTDOWN 0x0200 | |
139 | ||
140 | /* PHY Wakeup Registers and defines */ | |
141 | #define BM_PORT_GEN_CFG PHY_REG(BM_PORT_CTRL_PAGE, 17) | |
142 | #define BM_RCTL PHY_REG(BM_WUC_PAGE, 0) | |
143 | #define BM_WUC PHY_REG(BM_WUC_PAGE, 1) | |
144 | #define BM_WUFC PHY_REG(BM_WUC_PAGE, 2) | |
145 | #define BM_WUS PHY_REG(BM_WUC_PAGE, 3) | |
146 | #define BM_RAR_L(_i) (BM_PHY_REG(BM_WUC_PAGE, 16 + ((_i) << 2))) | |
147 | #define BM_RAR_M(_i) (BM_PHY_REG(BM_WUC_PAGE, 17 + ((_i) << 2))) | |
148 | #define BM_RAR_H(_i) (BM_PHY_REG(BM_WUC_PAGE, 18 + ((_i) << 2))) | |
149 | #define BM_RAR_CTRL(_i) (BM_PHY_REG(BM_WUC_PAGE, 19 + ((_i) << 2))) | |
150 | #define BM_MTA(_i) (BM_PHY_REG(BM_WUC_PAGE, 128 + ((_i) << 1))) | |
151 | ||
152 | #define BM_RCTL_UPE 0x0001 /* Unicast Promiscuous Mode */ | |
153 | #define BM_RCTL_MPE 0x0002 /* Multicast Promiscuous Mode */ | |
154 | #define BM_RCTL_MO_SHIFT 3 /* Multicast Offset Shift */ | |
155 | #define BM_RCTL_MO_MASK (3 << 3) /* Multicast Offset Mask */ | |
156 | #define BM_RCTL_BAM 0x0020 /* Broadcast Accept Mode */ | |
157 | #define BM_RCTL_PMCF 0x0040 /* Pass MAC Control Frames */ | |
158 | #define BM_RCTL_RFCE 0x0080 /* Rx Flow Control Enable */ | |
159 | ||
160 | #define HV_LED_CONFIG PHY_REG(768, 30) /* LED Configuration */ | |
161 | #define HV_MUX_DATA_CTRL PHY_REG(776, 16) | |
162 | #define HV_MUX_DATA_CTRL_GEN_TO_MAC 0x0400 | |
163 | #define HV_MUX_DATA_CTRL_FORCE_SPEED 0x0004 | |
164 | #define HV_STATS_PAGE 778 | |
165 | /* Half-duplex collision counts */ | |
166 | #define HV_SCC_UPPER PHY_REG(HV_STATS_PAGE, 16) /* Single Collision */ | |
167 | #define HV_SCC_LOWER PHY_REG(HV_STATS_PAGE, 17) | |
168 | #define HV_ECOL_UPPER PHY_REG(HV_STATS_PAGE, 18) /* Excessive Coll. */ | |
169 | #define HV_ECOL_LOWER PHY_REG(HV_STATS_PAGE, 19) | |
170 | #define HV_MCC_UPPER PHY_REG(HV_STATS_PAGE, 20) /* Multiple Collision */ | |
171 | #define HV_MCC_LOWER PHY_REG(HV_STATS_PAGE, 21) | |
172 | #define HV_LATECOL_UPPER PHY_REG(HV_STATS_PAGE, 23) /* Late Collision */ | |
173 | #define HV_LATECOL_LOWER PHY_REG(HV_STATS_PAGE, 24) | |
174 | #define HV_COLC_UPPER PHY_REG(HV_STATS_PAGE, 25) /* Collision */ | |
175 | #define HV_COLC_LOWER PHY_REG(HV_STATS_PAGE, 26) | |
176 | #define HV_DC_UPPER PHY_REG(HV_STATS_PAGE, 27) /* Defer Count */ | |
177 | #define HV_DC_LOWER PHY_REG(HV_STATS_PAGE, 28) | |
178 | #define HV_TNCRS_UPPER PHY_REG(HV_STATS_PAGE, 29) /* Tx with no CRS */ | |
179 | #define HV_TNCRS_LOWER PHY_REG(HV_STATS_PAGE, 30) | |
180 | ||
181 | #define E1000_FCRTV_PCH 0x05F40 /* PCH Flow Control Refresh Timer Value */ | |
182 | ||
183 | #define E1000_NVM_K1_CONFIG 0x1B /* NVM K1 Config Word */ | |
184 | #define E1000_NVM_K1_ENABLE 0x1 /* NVM Enable K1 bit */ | |
185 | #define K1_ENTRY_LATENCY 0 | |
186 | #define K1_MIN_TIME 1 | |
187 | ||
188 | /* SMBus Control Phy Register */ | |
189 | #define CV_SMB_CTRL PHY_REG(769, 23) | |
190 | #define CV_SMB_CTRL_FORCE_SMBUS 0x0001 | |
191 | ||
192 | #if !defined(EXTERNAL_RELEASE) || defined(ULP_SUPPORT) | |
193 | /* I218 Ultra Low Power Configuration 1 Register */ | |
194 | #define I218_ULP_CONFIG1 PHY_REG(779, 16) | |
195 | #define I218_ULP_CONFIG1_START 0x0001 /* Start auto ULP config */ | |
196 | #define I218_ULP_CONFIG1_IND 0x0004 /* Pwr up from ULP indication */ | |
197 | #define I218_ULP_CONFIG1_STICKY_ULP 0x0010 /* Set sticky ULP mode */ | |
198 | #define I218_ULP_CONFIG1_INBAND_EXIT 0x0020 /* Inband on ULP exit */ | |
199 | #define I218_ULP_CONFIG1_WOL_HOST 0x0040 /* WoL Host on ULP exit */ | |
200 | #define I218_ULP_CONFIG1_RESET_TO_SMBUS 0x0100 /* Reset to SMBus mode */ | |
201 | #define I218_ULP_CONFIG1_DISABLE_SMB_PERST 0x1000 /* Disable on PERST# */ | |
202 | ||
203 | #endif /* !EXTERNAL_RELEASE || ULP_SUPPORT */ | |
204 | /* SMBus Address Phy Register */ | |
205 | #define HV_SMB_ADDR PHY_REG(768, 26) | |
206 | #define HV_SMB_ADDR_MASK 0x007F | |
207 | #define HV_SMB_ADDR_PEC_EN 0x0200 | |
208 | #define HV_SMB_ADDR_VALID 0x0080 | |
209 | #define HV_SMB_ADDR_FREQ_MASK 0x1100 | |
210 | #define HV_SMB_ADDR_FREQ_LOW_SHIFT 8 | |
211 | #define HV_SMB_ADDR_FREQ_HIGH_SHIFT 12 | |
212 | ||
213 | /* Strapping Option Register - RO */ | |
214 | #define E1000_STRAP 0x0000C | |
215 | #define E1000_STRAP_SMBUS_ADDRESS_MASK 0x00FE0000 | |
216 | #define E1000_STRAP_SMBUS_ADDRESS_SHIFT 17 | |
217 | #define E1000_STRAP_SMT_FREQ_MASK 0x00003000 | |
218 | #define E1000_STRAP_SMT_FREQ_SHIFT 12 | |
219 | ||
220 | /* OEM Bits Phy Register */ | |
221 | #define HV_OEM_BITS PHY_REG(768, 25) | |
222 | #define HV_OEM_BITS_LPLU 0x0004 /* Low Power Link Up */ | |
223 | #define HV_OEM_BITS_GBE_DIS 0x0040 /* Gigabit Disable */ | |
224 | #define HV_OEM_BITS_RESTART_AN 0x0400 /* Restart Auto-negotiation */ | |
225 | ||
226 | /* KMRN Mode Control */ | |
227 | #define HV_KMRN_MODE_CTRL PHY_REG(769, 16) | |
228 | #define HV_KMRN_MDIO_SLOW 0x0400 | |
229 | ||
230 | /* KMRN FIFO Control and Status */ | |
231 | #define HV_KMRN_FIFO_CTRLSTA PHY_REG(770, 16) | |
232 | #define HV_KMRN_FIFO_CTRLSTA_PREAMBLE_MASK 0x7000 | |
233 | #define HV_KMRN_FIFO_CTRLSTA_PREAMBLE_SHIFT 12 | |
234 | ||
235 | /* PHY Power Management Control */ | |
236 | #define HV_PM_CTRL PHY_REG(770, 17) | |
237 | #define HV_PM_CTRL_PLL_STOP_IN_K1_GIGA 0x100 | |
238 | #define HV_PM_CTRL_K1_ENABLE 0x4000 | |
239 | ||
240 | #define SW_FLAG_TIMEOUT 1000 /* SW Semaphore flag timeout in ms */ | |
241 | ||
242 | /* Inband Control */ | |
243 | #define I217_INBAND_CTRL PHY_REG(770, 18) | |
244 | #define I217_INBAND_CTRL_LINK_STAT_TX_TIMEOUT_MASK 0x3F00 | |
245 | #define I217_INBAND_CTRL_LINK_STAT_TX_TIMEOUT_SHIFT 8 | |
246 | ||
247 | /* Low Power Idle GPIO Control */ | |
248 | #define I217_LPI_GPIO_CTRL PHY_REG(772, 18) | |
249 | #define I217_LPI_GPIO_CTRL_AUTO_EN_LPI 0x0800 | |
250 | ||
251 | /* PHY Low Power Idle Control */ | |
252 | #define I82579_LPI_CTRL PHY_REG(772, 20) | |
253 | #define I82579_LPI_CTRL_100_ENABLE 0x2000 | |
254 | #define I82579_LPI_CTRL_1000_ENABLE 0x4000 | |
255 | #define I82579_LPI_CTRL_ENABLE_MASK 0x6000 | |
256 | ||
257 | /* 82579 DFT Control */ | |
258 | #define I82579_DFT_CTRL PHY_REG(769, 20) | |
259 | #define I82579_DFT_CTRL_GATE_PHY_RESET 0x0040 /* Gate PHY Reset on MAC Reset */ | |
260 | ||
261 | /* Extended Management Interface (EMI) Registers */ | |
262 | #define I82579_EMI_ADDR 0x10 | |
263 | #define I82579_EMI_DATA 0x11 | |
264 | #define I82579_LPI_UPDATE_TIMER 0x4805 /* in 40ns units + 40 ns base value */ | |
265 | #define I82579_MSE_THRESHOLD 0x084F /* 82579 Mean Square Error Threshold */ | |
266 | #define I82577_MSE_THRESHOLD 0x0887 /* 82577 Mean Square Error Threshold */ | |
267 | #define I82579_MSE_LINK_DOWN 0x2411 /* MSE count before dropping link */ | |
268 | #define I82579_RX_CONFIG 0x3412 /* Receive configuration */ | |
269 | #define I82579_LPI_PLL_SHUT 0x4412 /* LPI PLL Shut Enable */ | |
270 | #define I82579_EEE_PCS_STATUS 0x182E /* IEEE MMD Register 3.1 >> 8 */ | |
271 | #define I82579_EEE_CAPABILITY 0x0410 /* IEEE MMD Register 3.20 */ | |
272 | #define I82579_EEE_ADVERTISEMENT 0x040E /* IEEE MMD Register 7.60 */ | |
273 | #define I82579_EEE_LP_ABILITY 0x040F /* IEEE MMD Register 7.61 */ | |
274 | #define I82579_EEE_100_SUPPORTED (1 << 1) /* 100BaseTx EEE */ | |
275 | #define I82579_EEE_1000_SUPPORTED (1 << 2) /* 1000BaseTx EEE */ | |
276 | #define I82579_LPI_100_PLL_SHUT (1 << 2) /* 100M LPI PLL Shut Enabled */ | |
277 | #define I217_EEE_PCS_STATUS 0x9401 /* IEEE MMD Register 3.1 */ | |
278 | #define I217_EEE_CAPABILITY 0x8000 /* IEEE MMD Register 3.20 */ | |
279 | #define I217_EEE_ADVERTISEMENT 0x8001 /* IEEE MMD Register 7.60 */ | |
280 | #define I217_EEE_LP_ABILITY 0x8002 /* IEEE MMD Register 7.61 */ | |
281 | #define I217_RX_CONFIG 0xB20C /* Receive configuration */ | |
282 | ||
283 | #define E1000_EEE_RX_LPI_RCVD 0x0400 /* Tx LP idle received */ | |
284 | #define E1000_EEE_TX_LPI_RCVD 0x0800 /* Rx LP idle received */ | |
285 | ||
286 | /* Intel Rapid Start Technology Support */ | |
287 | #define I217_PROXY_CTRL BM_PHY_REG(BM_WUC_PAGE, 70) | |
288 | #define I217_PROXY_CTRL_AUTO_DISABLE 0x0080 | |
289 | #define I217_SxCTRL PHY_REG(BM_PORT_CTRL_PAGE, 28) | |
290 | #define I217_SxCTRL_ENABLE_LPI_RESET 0x1000 | |
291 | #define I217_CGFREG PHY_REG(772, 29) | |
292 | #define I217_CGFREG_ENABLE_MTA_RESET 0x0002 | |
293 | #define I217_MEMPWR PHY_REG(772, 26) | |
294 | #define I217_MEMPWR_DISABLE_SMB_RELEASE 0x0010 | |
295 | ||
296 | /* Receive Address Initial CRC Calculation */ | |
297 | #define E1000_PCH_RAICC(_n) (0x05F50 + ((_n) * 4)) | |
298 | ||
299 | #if defined(QV_RELEASE) || !defined(NO_PCH_LPT_B0_SUPPORT) | |
300 | #define E1000_PCI_REVISION_ID_REG 0x08 | |
301 | #endif /* defined(QV_RELEASE) || !defined(NO_PCH_LPT_B0_SUPPORT) */ | |
302 | void e1000_set_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw, | |
303 | bool state); | |
304 | void e1000_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw); | |
305 | void e1000_gig_downshift_workaround_ich8lan(struct e1000_hw *hw); | |
306 | void e1000_suspend_workarounds_ich8lan(struct e1000_hw *hw); | |
307 | u32 e1000_resume_workarounds_pchlan(struct e1000_hw *hw); | |
308 | s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable); | |
309 | s32 e1000_configure_k0s_lpt(struct e1000_hw *hw, u8 entry_latency, u8 min_time); | |
310 | void e1000_copy_rx_addrs_to_phy_ich8lan(struct e1000_hw *hw); | |
311 | s32 e1000_lv_jumbo_workaround_ich8lan(struct e1000_hw *hw, bool enable); | |
312 | s32 e1000_read_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 *data); | |
313 | s32 e1000_write_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 data); | |
314 | s32 e1000_set_eee_pchlan(struct e1000_hw *hw); | |
315 | #ifdef ULP_SUPPORT | |
316 | s32 e1000_enable_ulp_lpt_lp(struct e1000_hw *hw, bool to_sx); | |
317 | s32 e1000_disable_ulp_lpt_lp(struct e1000_hw *hw, bool force); | |
318 | #endif /* ULP_SUPPORT */ | |
319 | #endif /* _E1000_ICH8LAN_H_ */ | |
320 | void e1000_demote_ltr(struct e1000_hw *hw, bool demote, bool link); |