/** @file\r
Header file for Sata Controller driver.\r
\r
- Copyright (c) 2011 - 2016, Intel Corporation. All rights reserved.<BR>\r
+ Copyright (c) 2011 - 2018, Intel Corporation. All rights reserved.<BR>\r
Copyright (c) 2018, ARM Ltd. All rights reserved.<BR>\r
This program and the accompanying materials\r
are licensed and made available under the terms and conditions of the BSD License\r
);\r
\r
/**\r
- This routine is called right after the .Supported() called and \r
+ This routine is called right after the .Supported() called and\r
Start this driver on ControllerHandle.\r
\r
@param This Protocol instance pointer.\r
@param This A pointer to the EFI_DRIVER_BINDING_PROTOCOL instance.\r
@param Controller A handle to the device being stopped.\r
@param NumberOfChildren The number of child device handles in ChildHandleBuffer.\r
- @param ChildHandleBuffer An array of child handles to be freed. \r
+ @param ChildHandleBuffer An array of child handles to be freed.\r
\r
@retval EFI_SUCCESS This driver is removed from this device.\r
@retval other Some error occurs when removing this driver from this device.\r
//\r
/**\r
Returns the information about the specified IDE channel.\r
- \r
+\r
This function can be used to obtain information about a particular IDE channel.\r
- The driver entity uses this information during the enumeration process. \r
- \r
- If Enabled is set to FALSE, the driver entity will not scan the channel. Note \r
+ The driver entity uses this information during the enumeration process.\r
+\r
+ If Enabled is set to FALSE, the driver entity will not scan the channel. Note\r
that it will not prevent an operating system driver from scanning the channel.\r
- \r
- For most of today's controllers, MaxDevices will either be 1 or 2. For SATA \r
- controllers, this value will always be 1. SATA configurations can contain SATA \r
+\r
+ For most of today's controllers, MaxDevices will either be 1 or 2. For SATA\r
+ controllers, this value will always be 1. SATA configurations can contain SATA\r
port multipliers. SATA port multipliers behave like SATA bridges and can support\r
- up to 16 devices on the other side. If a SATA port out of the IDE controller \r
- is connected to a port multiplier, MaxDevices will be set to the number of SATA \r
- devices that the port multiplier supports. Because today's port multipliers \r
- support up to fifteen SATA devices, this number can be as large as fifteen. The IDE \r
- bus driver is required to scan for the presence of port multipliers behind an SATA \r
- controller and enumerate up to MaxDevices number of devices behind the port \r
- multiplier. \r
- \r
- In this context, the devices behind a port multiplier constitute a channel. \r
- \r
+ up to 16 devices on the other side. If a SATA port out of the IDE controller\r
+ is connected to a port multiplier, MaxDevices will be set to the number of SATA\r
+ devices that the port multiplier supports. Because today's port multipliers\r
+ support up to fifteen SATA devices, this number can be as large as fifteen. The IDE\r
+ bus driver is required to scan for the presence of port multipliers behind an SATA\r
+ controller and enumerate up to MaxDevices number of devices behind the port\r
+ multiplier.\r
+\r
+ In this context, the devices behind a port multiplier constitute a channel.\r
+\r
@param[in] This The pointer to the EFI_IDE_CONTROLLER_INIT_PROTOCOL instance.\r
@param[in] Channel Zero-based channel number.\r
- @param[out] Enabled TRUE if this channel is enabled. Disabled channels \r
+ @param[out] Enabled TRUE if this channel is enabled. Disabled channels\r
are not scanned to see if any devices are present.\r
@param[out] MaxDevices The maximum number of IDE devices that the bus driver\r
- can expect on this channel. For the ATA/ATAPI \r
- specification, version 6, this number will either be \r
- one or two. For Serial ATA (SATA) configurations with a \r
+ can expect on this channel. For the ATA/ATAPI\r
+ specification, version 6, this number will either be\r
+ one or two. For Serial ATA (SATA) configurations with a\r
port multiplier, this number can be as large as fifteen.\r
\r
\r
/**\r
The notifications from the driver entity that it is about to enter a certain\r
phase of the IDE channel enumeration process.\r
- \r
- This function can be used to notify the IDE controller driver to perform \r
- specific actions, including any chipset-specific initialization, so that the \r
- chipset is ready to enter the next phase. Seven notification points are defined \r
- at this time. \r
- \r
- More synchronization points may be added as required in the future. \r
+\r
+ This function can be used to notify the IDE controller driver to perform\r
+ specific actions, including any chipset-specific initialization, so that the\r
+ chipset is ready to enter the next phase. Seven notification points are defined\r
+ at this time.\r
+\r
+ More synchronization points may be added as required in the future.\r
\r
@param[in] This The pointer to the EFI_IDE_CONTROLLER_INIT_PROTOCOL\r
instance.\r
@retval EFI_SUCCESS The notification was accepted without any errors.\r
@retval EFI_UNSUPPORTED Phase is not supported.\r
@retval EFI_INVALID_PARAMETER Channel is invalid (Channel >= ChannelCount).\r
- @retval EFI_NOT_READY This phase cannot be entered at this time; for \r
- example, an attempt was made to enter a Phase \r
- without having entered one or more previous \r
+ @retval EFI_NOT_READY This phase cannot be entered at this time; for\r
+ example, an attempt was made to enter a Phase\r
+ without having entered one or more previous\r
Phase.\r
\r
**/\r
/**\r
Submits the device information to the IDE controller driver.\r
\r
- This function is used by the driver entity to pass detailed information about \r
- a particular device to the IDE controller driver. The driver entity obtains \r
+ This function is used by the driver entity to pass detailed information about\r
+ a particular device to the IDE controller driver. The driver entity obtains\r
this information by issuing an ATA or ATAPI IDENTIFY_DEVICE command. IdentifyData\r
- is the pointer to the response data buffer. The IdentifyData buffer is owned \r
- by the driver entity, and the IDE controller driver must make a local copy \r
- of the entire buffer or parts of the buffer as needed. The original IdentifyData \r
+ is the pointer to the response data buffer. The IdentifyData buffer is owned\r
+ by the driver entity, and the IDE controller driver must make a local copy\r
+ of the entire buffer or parts of the buffer as needed. The original IdentifyData\r
buffer pointer may not be valid when\r
- \r
+\r
- EFI_IDE_CONTROLLER_INIT_PROTOCOL.CalculateMode() or\r
- EFI_IDE_CONTROLLER_INIT_PROTOCOL.DisqualifyMode() is called at a later point.\r
- \r
- The IDE controller driver may consult various fields of EFI_IDENTIFY_DATA to \r
- compute the optimum mode for the device. These fields are not limited to the \r
- timing information. For example, an implementation of the IDE controller driver \r
- may examine the vendor and type/mode field to match known bad drives. \r
- \r
- The driver entity may submit drive information in any order, as long as it \r
- submits information for all the devices belonging to the enumeration group \r
+\r
+ The IDE controller driver may consult various fields of EFI_IDENTIFY_DATA to\r
+ compute the optimum mode for the device. These fields are not limited to the\r
+ timing information. For example, an implementation of the IDE controller driver\r
+ may examine the vendor and type/mode field to match known bad drives.\r
+\r
+ The driver entity may submit drive information in any order, as long as it\r
+ submits information for all the devices belonging to the enumeration group\r
before EFI_IDE_CONTROLLER_INIT_PROTOCOL.CalculateMode() is called for any device\r
in that enumeration group. If a device is absent, EFI_IDE_CONTROLLER_INIT_PROTOCOL.SubmitData()\r
- should be called with IdentifyData set to NULL. The IDE controller driver may \r
- not have any other mechanism to know whether a device is present or not. Therefore, \r
- setting IdentifyData to NULL does not constitute an error condition. \r
- EFI_IDE_CONTROLLER_INIT_PROTOCOL.SubmitData() can be called only once for a \r
- given (Channel, Device) pair. \r
- \r
+ should be called with IdentifyData set to NULL. The IDE controller driver may\r
+ not have any other mechanism to know whether a device is present or not. Therefore,\r
+ setting IdentifyData to NULL does not constitute an error condition.\r
+ EFI_IDE_CONTROLLER_INIT_PROTOCOL.SubmitData() can be called only once for a\r
+ given (Channel, Device) pair.\r
+\r
@param[in] This A pointer to the EFI_IDE_CONTROLLER_INIT_PROTOCOL instance.\r
@param[in] Channel Zero-based channel number.\r
@param[in] Device Zero-based device number on the Channel.\r
/**\r
Disqualifies specific modes for an IDE device.\r
\r
- This function allows the driver entity or other drivers (such as platform \r
+ This function allows the driver entity or other drivers (such as platform\r
drivers) to reject certain timing modes and request the IDE controller driver\r
- to recalculate modes. This function allows the driver entity and the IDE \r
- controller driver to negotiate the timings on a per-device basis. This function \r
- is useful in the case of drives that lie about their capabilities. An example \r
- is when the IDE device fails to accept the timing modes that are calculated \r
+ to recalculate modes. This function allows the driver entity and the IDE\r
+ controller driver to negotiate the timings on a per-device basis. This function\r
+ is useful in the case of drives that lie about their capabilities. An example\r
+ is when the IDE device fails to accept the timing modes that are calculated\r
by the IDE controller driver based on the response to the Identify Drive command.\r
\r
- If the driver entity does not want to limit the ATA timing modes and leave that \r
- decision to the IDE controller driver, it can either not call this function for \r
- the given device or call this function and set the Valid flag to FALSE for all \r
+ If the driver entity does not want to limit the ATA timing modes and leave that\r
+ decision to the IDE controller driver, it can either not call this function for\r
+ the given device or call this function and set the Valid flag to FALSE for all\r
modes that are listed in EFI_ATA_COLLECTIVE_MODE.\r
- \r
- The driver entity may disqualify modes for a device in any order and any number \r
+\r
+ The driver entity may disqualify modes for a device in any order and any number\r
of times.\r
- \r
- This function can be called multiple times to invalidate multiple modes of the \r
- same type (e.g., Programmed Input/Output [PIO] modes 3 and 4). See the ATA/ATAPI \r
- specification for more information on PIO modes. \r
- \r
+\r
+ This function can be called multiple times to invalidate multiple modes of the\r
+ same type (e.g., Programmed Input/Output [PIO] modes 3 and 4). See the ATA/ATAPI\r
+ specification for more information on PIO modes.\r
+\r
For Serial ATA (SATA) controllers, this member function can be used to disqualify\r
a higher transfer rate mode on a given channel. For example, a platform driver\r
- may inform the IDE controller driver to not use second-generation (Gen2) speeds \r
+ may inform the IDE controller driver to not use second-generation (Gen2) speeds\r
for a certain SATA drive.\r
- \r
+\r
@param[in] This The pointer to the EFI_IDE_CONTROLLER_INIT_PROTOCOL instance.\r
@param[in] Channel The zero-based channel number.\r
@param[in] Device The zero-based device number on the Channel.\r
@retval EFI_INVALID_PARAMETER Channel is invalid (Channel >= ChannelCount).\r
@retval EFI_INVALID_PARAMETER Device is invalid.\r
@retval EFI_INVALID_PARAMETER IdentifyData is NULL.\r
- \r
+\r
**/\r
EFI_STATUS\r
EFIAPI\r
Returns the information about the optimum modes for the specified IDE device.\r
\r
This function is used by the driver entity to obtain the optimum ATA modes for\r
- a specific device. The IDE controller driver takes into account the following \r
+ a specific device. The IDE controller driver takes into account the following\r
while calculating the mode:\r
- The IdentifyData inputs to EFI_IDE_CONTROLLER_INIT_PROTOCOL.SubmitData()\r
- The BadModes inputs to EFI_IDE_CONTROLLER_INIT_PROTOCOL.DisqualifyMode()\r
\r
- The driver entity is required to call EFI_IDE_CONTROLLER_INIT_PROTOCOL.SubmitData() \r
- for all the devices that belong to an enumeration group before calling \r
- EFI_IDE_CONTROLLER_INIT_PROTOCOL.CalculateMode() for any device in the same group. \r
- \r
- The IDE controller driver will use controller- and possibly platform-specific \r
- algorithms to arrive at SupportedModes. The IDE controller may base its \r
- decision on user preferences and other considerations as well. This function \r
- may be called multiple times because the driver entity may renegotiate the mode \r
+ The driver entity is required to call EFI_IDE_CONTROLLER_INIT_PROTOCOL.SubmitData()\r
+ for all the devices that belong to an enumeration group before calling\r
+ EFI_IDE_CONTROLLER_INIT_PROTOCOL.CalculateMode() for any device in the same group.\r
+\r
+ The IDE controller driver will use controller- and possibly platform-specific\r
+ algorithms to arrive at SupportedModes. The IDE controller may base its\r
+ decision on user preferences and other considerations as well. This function\r
+ may be called multiple times because the driver entity may renegotiate the mode\r
with the IDE controller driver using EFI_IDE_CONTROLLER_INIT_PROTOCOL.DisqualifyMode().\r
- \r
- The driver entity may collect timing information for various devices in any \r
+\r
+ The driver entity may collect timing information for various devices in any\r
order. The driver entity is responsible for making sure that all the dependencies\r
- are satisfied. For example, the SupportedModes information for device A that \r
- was previously returned may become stale after a call to \r
+ are satisfied. For example, the SupportedModes information for device A that\r
+ was previously returned may become stale after a call to\r
EFI_IDE_CONTROLLER_INIT_PROTOCOL.DisqualifyMode() for device B.\r
- \r
- The buffer SupportedModes is allocated by the callee because the caller does \r
- not necessarily know the size of the buffer. The type EFI_ATA_COLLECTIVE_MODE \r
- is defined in a way that allows for future extensibility and can be of variable \r
- length. This memory pool should be deallocated by the caller when it is no \r
- longer necessary. \r
- \r
- The IDE controller driver for a Serial ATA (SATA) controller can use this \r
- member function to force a lower speed (first-generation [Gen1] speeds on a \r
- second-generation [Gen2]-capable hardware). The IDE controller driver can \r
- also allow the driver entity to stay with the speed that has been negotiated \r
+\r
+ The buffer SupportedModes is allocated by the callee because the caller does\r
+ not necessarily know the size of the buffer. The type EFI_ATA_COLLECTIVE_MODE\r
+ is defined in a way that allows for future extensibility and can be of variable\r
+ length. This memory pool should be deallocated by the caller when it is no\r
+ longer necessary.\r
+\r
+ The IDE controller driver for a Serial ATA (SATA) controller can use this\r
+ member function to force a lower speed (first-generation [Gen1] speeds on a\r
+ second-generation [Gen2]-capable hardware). The IDE controller driver can\r
+ also allow the driver entity to stay with the speed that has been negotiated\r
by the physical layer.\r
- \r
+\r
@param[in] This The pointer to the EFI_IDE_CONTROLLER_INIT_PROTOCOL instance.\r
@param[in] Channel A zero-based channel number.\r
@param[in] Device A zero-based device number on the Channel.\r
\r
@retval EFI_SUCCESS SupportedModes was returned.\r
@retval EFI_INVALID_PARAMETER Channel is invalid (Channel >= ChannelCount).\r
- @retval EFI_INVALID_PARAMETER Device is invalid. \r
+ @retval EFI_INVALID_PARAMETER Device is invalid.\r
@retval EFI_INVALID_PARAMETER SupportedModes is NULL.\r
- @retval EFI_NOT_READY Modes cannot be calculated due to a lack of \r
- data. This error may happen if \r
- EFI_IDE_CONTROLLER_INIT_PROTOCOL.SubmitData() \r
- and EFI_IDE_CONTROLLER_INIT_PROTOCOL.DisqualifyData() \r
- were not called for at least one drive in the \r
+ @retval EFI_NOT_READY Modes cannot be calculated due to a lack of\r
+ data. This error may happen if\r
+ EFI_IDE_CONTROLLER_INIT_PROTOCOL.SubmitData()\r
+ and EFI_IDE_CONTROLLER_INIT_PROTOCOL.DisqualifyData()\r
+ were not called for at least one drive in the\r
same enumeration group.\r
\r
**/\r
Commands the IDE controller driver to program the IDE controller hardware\r
so that the specified device can operate at the specified mode.\r
\r
- This function is used by the driver entity to instruct the IDE controller \r
- driver to program the IDE controller hardware to the specified modes. This \r
- function can be called only once for a particular device. For a Serial ATA \r
+ This function is used by the driver entity to instruct the IDE controller\r
+ driver to program the IDE controller hardware to the specified modes. This\r
+ function can be called only once for a particular device. For a Serial ATA\r
(SATA) Advanced Host Controller Interface (AHCI) controller, no controller-\r
specific programming may be required.\r
\r