Default Configuration using a Bridge
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+[thumbnail="default-network-setup-bridge.svg"]
Bridges are like physical network switches implemented in software.
All VMs can share a single bridge, or you can create multiple bridges to
separate network domains. Each host can have up to 4094 bridges.
reasons, they disable networking as soon as they detect multiple MAC
addresses on a single interface.
-TIP: Some providers allows you to register additional MACs on there
+TIP: Some providers allows you to register additional MACs on their
management interface. This avoids the problem, but is clumsy to
configure because you need to register a MAC for each of your VMs.
interface. This makes sure that all network packets use the same MAC
address.
+[thumbnail="default-network-setup-routed.svg"]
A common scenario is that you have a public IP (assume `198.51.100.5`
for this example), and an additional IP block for your VMs
(`203.0.113.16/29`). We recommend the following setup for such
----
+[thumbnail="default-network-setup-bond.svg"]
Another possibility it to use the bond directly as bridge port.
This can be used to make the guest network fault-tolerant.
----
+
+VLAN 802.1Q
+~~~~~~~~~~~
+
+A virtual LAN (VLAN) is a broadcast domain that is partitioned and
+isolated in the network at layer two. So it is possible to have
+multiple networks (4096) in a physical network, each independent of
+the other ones.
+
+Each VLAN network is identified by a number often called 'tag'.
+Network packages are then 'tagged' to identify which virtual network
+they belong to.
+
+
+VLAN for Guest Networks
+^^^^^^^^^^^^^^^^^^^^^^^
+
+{pve} supports this setup out of the box. You can specify the VLAN tag
+when you create a VM. The VLAN tag is part of the guest network
+configuration. The networking layer supports differnet modes to
+implement VLANs, depending on the bridge configuration:
+
+* *VLAN awareness on the Linux bridge:*
+In this case, each guest's virtual network card is assigned to a VLAN tag,
+which is transparently supported by the Linux bridge.
+Trunk mode is also possible, but that makes the configuration
+in the guest necessary.
+
+* *"traditional" VLAN on the Linux bridge:*
+In contrast to the VLAN awareness method, this method is not transparent
+and creates a VLAN device with associated bridge for each VLAN.
+That is, if e.g. in our default network, a guest VLAN 5 is used
+to create eno1.5 and vmbr0v5, which remains until rebooting.
+
+* *Open vSwitch VLAN:*
+This mode uses the OVS VLAN feature.
+
+* *Guest configured VLAN:*
+VLANs are assigned inside the guest. In this case, the setup is
+completely done inside the guest and can not be influenced from the
+outside. The benefit is that you can use more than one VLAN on a
+single virtual NIC.
+
+
+VLAN on the Host
+^^^^^^^^^^^^^^^^
+
+To allow host communication with an isolated network. It is possible
+to apply VLAN tags to any network device (NIC, Bond, Bridge). In
+general, you should configure the VLAN on the interface with the least
+abstraction layers between itself and the physical NIC.
+
+For example, in a default configuration where you want to place
+the host management address on a separate VLAN.
+
+
+.Example: Use VLAN 5 for the {pve} management IP with traditional Linux bridge
+----
+auto lo
+iface lo inet loopback
+
+iface eno1 inet manual
+
+iface eno1.5 inet manual
+
+auto vmbr0v5
+iface vmbr0v5 inet static
+ address 10.10.10.2
+ netmask 255.255.255.0
+ gateway 10.10.10.1
+ bridge_ports eno1.5
+ bridge_stp off
+ bridge_fd 0
+
+auto vmbr0
+iface vmbr0 inet manual
+ bridge_ports eno1
+ bridge_stp off
+ bridge_fd 0
+
+----
+
+.Example: Use VLAN 5 for the {pve} management IP with VLAN aware Linux bridge
+----
+auto lo
+iface lo inet loopback
+
+iface eno1 inet manual
+
+
+auto vmbr0.5
+iface vmbr0.5 inet static
+ address 10.10.10.2
+ netmask 255.255.255.0
+ gateway 10.10.10.1
+
+auto vmbr0
+iface vmbr0 inet manual
+ bridge_ports eno1
+ bridge_stp off
+ bridge_fd 0
+ bridge_vlan_aware yes
+----
+
+The next example is the same setup but a bond is used to
+make this network fail-safe.
+
+.Example: Use VLAN 5 with bond0 for the {pve} management IP with traditional Linux bridge
+----
+auto lo
+iface lo inet loopback
+
+iface eno1 inet manual
+
+iface eno2 inet manual
+
+auto bond0
+iface bond0 inet manual
+ slaves eno1 eno2
+ bond_miimon 100
+ bond_mode 802.3ad
+ bond_xmit_hash_policy layer2+3
+
+iface bond0.5 inet manual
+
+auto vmbr0v5
+iface vmbr0v5 inet static
+ address 10.10.10.2
+ netmask 255.255.255.0
+ gateway 10.10.10.1
+ bridge_ports bond0.5
+ bridge_stp off
+ bridge_fd 0
+
+auto vmbr0
+iface vmbr0 inet manual
+ bridge_ports bond0
+ bridge_stp off
+ bridge_fd 0
+
+----
+
////
TODO: explain IPv6 support?
TODO: explain OVS