##
{ 'command': 'query-commands', 'returns': ['CommandInfo'] }
+##
+# @MigrationStats
+#
+# Detailed migration status.
+#
+# @transferred: amount of bytes already transferred to the target VM
+#
+# @remaining: amount of bytes remaining to be transferred to the target VM
+#
+# @total: total amount of bytes involved in the migration process
+#
+# Since: 0.14.0.
+##
+{ 'type': 'MigrationStats',
+ 'data': {'transferred': 'int', 'remaining': 'int', 'total': 'int' } }
+
+##
+# @MigrationInfo
+#
+# Information about current migration process.
+#
+# @status: #optional string describing the current migration status.
+# As of 0.14.0 this can be 'active', 'completed', 'failed' or
+# 'cancelled'. If this field is not returned, no migration process
+# has been initiated
+#
+# @ram: #optional @MigrationStats containing detailed migration status,
+# only returned if status is 'active'
+#
+# @disk: #optional @MigrationStats containing detailed disk migration
+# status, only returned if status is 'active' and it is a block
+# migration
+#
+# Since: 0.14.0
+##
+{ 'type': 'MigrationInfo',
+ 'data': {'*status': 'str', '*ram': 'MigrationStats',
+ '*disk': 'MigrationStats'} }
+
+##
+# @query-migrate
+#
+# Returns information about current migration process.
+#
+# Returns: @MigrationInfo
+#
+# Since: 0.14.0
+##
+{ 'command': 'query-migrate', 'returns': 'MigrationInfo' }
+
##
# @MouseInfo:
#
{ 'command': 'query-mice', 'returns': ['MouseInfo'] }
##
-# @quit:
+# @CpuInfo:
#
-# This command will cause the QEMU process to exit gracefully. While every
-# attempt is made to send the QMP response before terminating, this is not
-# guaranteed. When using this interface, a premature EOF would not be
-# unexpected.
+# Information about a virtual CPU
+#
+# @CPU: the index of the virtual CPU
+#
+# @current: this only exists for backwards compatible and should be ignored
+#
+# @halted: true if the virtual CPU is in the halt state. Halt usually refers
+# to a processor specific low power mode.
+#
+# @pc: #optional If the target is i386 or x86_64, this is the 64-bit instruction
+# pointer.
+# If the target is Sparc, this is the PC component of the
+# instruction pointer.
+#
+# @nip: #optional If the target is PPC, the instruction pointer
+#
+# @npc: #optional If the target is Sparc, the NPC component of the instruction
+# pointer
+#
+# @PC: #optional If the target is MIPS, the instruction pointer
+#
+# @thread_id: ID of the underlying host thread
#
# Since: 0.14.0
+#
+# Notes: @halted is a transient state that changes frequently. By the time the
+# data is sent to the client, the guest may no longer be halted.
##
-{ 'command': 'quit' }
+{ 'type': 'CpuInfo',
+ 'data': {'CPU': 'int', 'current': 'bool', 'halted': 'bool', '*pc': 'int',
+ '*nip': 'int', '*npc': 'int', '*PC': 'int', 'thread_id': 'int'} }
##
-# @stop:
+# @query-cpus:
#
-# Stop all guest VCPU execution.
+# Returns a list of information about each virtual CPU.
+#
+# Returns: a list of @CpuInfo for each virtual CPU
+#
+# Since: 0.14.0
+##
+{ 'command': 'query-cpus', 'returns': ['CpuInfo'] }
+
+##
+# @BlockDeviceInfo:
+#
+# Information about the backing device for a block device.
+#
+# @file: the filename of the backing device
+#
+# @ro: true if the backing device was open read-only
+#
+# @drv: the name of the block format used to open the backing device. As of
+# 0.14.0 this can be: 'blkdebug', 'bochs', 'cloop', 'cow', 'dmg',
+# 'file', 'file', 'ftp', 'ftps', 'host_cdrom', 'host_device',
+# 'host_floppy', 'http', 'https', 'nbd', 'parallels', 'qcow',
+# 'qcow2', 'raw', 'tftp', 'vdi', 'vmdk', 'vpc', 'vvfat'
+#
+# @backing_file: #optional the name of the backing file (for copy-on-write)
+#
+# @encrypted: true if the backing device is encrypted
+#
+# @bps: total throughput limit in bytes per second is specified
+#
+# @bps_rd: read throughput limit in bytes per second is specified
+#
+# @bps_wr: write throughput limit in bytes per second is specified
+#
+# @iops: total I/O operations per second is specified
+#
+# @iops_rd: read I/O operations per second is specified
+#
+# @iops_wr: write I/O operations per second is specified
+#
+# Since: 0.14.0
+#
+# Notes: This interface is only found in @BlockInfo.
+##
+{ 'type': 'BlockDeviceInfo',
+ 'data': { 'file': 'str', 'ro': 'bool', 'drv': 'str',
+ '*backing_file': 'str', 'encrypted': 'bool',
+ 'bps': 'int', 'bps_rd': 'int', 'bps_wr': 'int',
+ 'iops': 'int', 'iops_rd': 'int', 'iops_wr': 'int'} }
+
+##
+# @BlockDeviceIoStatus:
+#
+# An enumeration of block device I/O status.
+#
+# @ok: The last I/O operation has succeeded
+#
+# @failed: The last I/O operation has failed
+#
+# @nospace: The last I/O operation has failed due to a no-space condition
+#
+# Since: 1.0
+##
+{ 'enum': 'BlockDeviceIoStatus', 'data': [ 'ok', 'failed', 'nospace' ] }
+
+##
+# @BlockInfo:
+#
+# Block device information. This structure describes a virtual device and
+# the backing device associated with it.
+#
+# @device: The device name associated with the virtual device.
+#
+# @type: This field is returned only for compatibility reasons, it should
+# not be used (always returns 'unknown')
+#
+# @removable: True if the device supports removable media.
+#
+# @locked: True if the guest has locked this device from having its media
+# removed
+#
+# @tray_open: #optional True if the device has a tray and it is open
+# (only present if removable is true)
+#
+# @io-status: #optional @BlockDeviceIoStatus. Only present if the device
+# supports it and the VM is configured to stop on errors
+#
+# @inserted: #optional @BlockDeviceInfo describing the device if media is
+# present
#
# Since: 0.14.0
+##
+{ 'type': 'BlockInfo',
+ 'data': {'device': 'str', 'type': 'str', 'removable': 'bool',
+ 'locked': 'bool', '*inserted': 'BlockDeviceInfo',
+ '*tray_open': 'bool', '*io-status': 'BlockDeviceIoStatus'} }
+
+##
+# @query-block:
#
-# Notes: This function will succeed even if the guest is already in the stopped
-# state
+# Get a list of BlockInfo for all virtual block devices.
+#
+# Returns: a list of @BlockInfo describing each virtual block device
+#
+# Since: 0.14.0
##
-{ 'command': 'stop' }
+{ 'command': 'query-block', 'returns': ['BlockInfo'] }
##
-# @system_reset:
+# @BlockDeviceStats:
#
-# Performs a hard reset of a guest.
+# Statistics of a virtual block device or a block backing device.
+#
+# @rd_bytes: The number of bytes read by the device.
+#
+# @wr_bytes: The number of bytes written by the device.
+#
+# @rd_operations: The number of read operations performed by the device.
+#
+# @wr_operations: The number of write operations performed by the device.
+#
+# @flush_operations: The number of cache flush operations performed by the
+# device (since 0.15.0)
+#
+# @flush_total_time_ns: Total time spend on cache flushes in nano-seconds
+# (since 0.15.0).
+#
+# @wr_total_time_ns: Total time spend on writes in nano-seconds (since 0.15.0).
+#
+# @rd_total_time_ns: Total_time_spend on reads in nano-seconds (since 0.15.0).
+#
+# @wr_highest_offset: The offset after the greatest byte written to the
+# device. The intended use of this information is for
+# growable sparse files (like qcow2) that are used on top
+# of a physical device.
#
# Since: 0.14.0
##
-{ 'command': 'system_reset' }
+{ 'type': 'BlockDeviceStats',
+ 'data': {'rd_bytes': 'int', 'wr_bytes': 'int', 'rd_operations': 'int',
+ 'wr_operations': 'int', 'flush_operations': 'int',
+ 'flush_total_time_ns': 'int', 'wr_total_time_ns': 'int',
+ 'rd_total_time_ns': 'int', 'wr_highest_offset': 'int' } }
##
-# @system_powerdown:
+# @BlockStats:
#
-# Requests that a guest perform a powerdown operation.
+# Statistics of a virtual block device or a block backing device.
+#
+# @device: #optional If the stats are for a virtual block device, the name
+# corresponding to the virtual block device.
+#
+# @stats: A @BlockDeviceStats for the device.
+#
+# @parent: #optional This may point to the backing block device if this is a
+# a virtual block device. If it's a backing block, this will point
+# to the backing file is one is present.
#
# Since: 0.14.0
+##
+{ 'type': 'BlockStats',
+ 'data': {'*device': 'str', 'stats': 'BlockDeviceStats',
+ '*parent': 'BlockStats'} }
+
+##
+# @query-blockstats:
#
-# Notes: A guest may or may not respond to this command. This command
-# returning does not indicate that a guest has accepted the request or
-# that it has shut down. Many guests will respond to this command by
-# prompting the user in some way.
+# Query the @BlockStats for all virtual block devices.
+#
+# Returns: A list of @BlockStats for each virtual block devices.
+#
+# Since: 0.14.0
##
-{ 'command': 'system_powerdown' }
+{ 'command': 'query-blockstats', 'returns': ['BlockStats'] }
+
+##
+# @VncClientInfo:
+#
+# Information about a connected VNC client.
+#
+# @host: The host name of the client. QEMU tries to resolve this to a DNS name
+# when possible.
+#
+# @family: 'ipv6' if the client is connected via IPv6 and TCP
+# 'ipv4' if the client is connected via IPv4 and TCP
+# 'unix' if the client is connected via a unix domain socket
+# 'unknown' otherwise
+#
+# @service: The service name of the client's port. This may depends on the
+# host system's service database so symbolic names should not be
+# relied on.
+#
+# @x509_dname: #optional If x509 authentication is in use, the Distinguished
+# Name of the client.
+#
+# @sasl_username: #optional If SASL authentication is in use, the SASL username
+# used for authentication.
+#
+# Since: 0.14.0
+##
+{ 'type': 'VncClientInfo',
+ 'data': {'host': 'str', 'family': 'str', 'service': 'str',
+ '*x509_dname': 'str', '*sasl_username': 'str'} }
+
+##
+# @VncInfo:
+#
+# Information about the VNC session.
+#
+# @enabled: true if the VNC server is enabled, false otherwise
+#
+# @host: #optional The hostname the VNC server is bound to. This depends on
+# the name resolution on the host and may be an IP address.
+#
+# @family: #optional 'ipv6' if the host is listening for IPv6 connections
+# 'ipv4' if the host is listening for IPv4 connections
+# 'unix' if the host is listening on a unix domain socket
+# 'unknown' otherwise
+#
+# @service: #optional The service name of the server's port. This may depends
+# on the host system's service database so symbolic names should not
+# be relied on.
+#
+# @auth: #optional the current authentication type used by the server
+# 'none' if no authentication is being used
+# 'vnc' if VNC authentication is being used
+# 'vencrypt+plain' if VEncrypt is used with plain text authentication
+# 'vencrypt+tls+none' if VEncrypt is used with TLS and no authentication
+# 'vencrypt+tls+vnc' if VEncrypt is used with TLS and VNC authentication
+# 'vencrypt+tls+plain' if VEncrypt is used with TLS and plain text auth
+# 'vencrypt+x509+none' if VEncrypt is used with x509 and no auth
+# 'vencrypt+x509+vnc' if VEncrypt is used with x509 and VNC auth
+# 'vencrypt+x509+plain' if VEncrypt is used with x509 and plain text auth
+# 'vencrypt+tls+sasl' if VEncrypt is used with TLS and SASL auth
+# 'vencrypt+x509+sasl' if VEncrypt is used with x509 and SASL auth
+#
+# @clients: a list of @VncClientInfo of all currently connected clients
+#
+# Since: 0.14.0
+##
+{ 'type': 'VncInfo',
+ 'data': {'enabled': 'bool', '*host': 'str', '*family': 'str',
+ '*service': 'str', '*auth': 'str', '*clients': ['VncClientInfo']} }
+
+##
+# @query-vnc:
+#
+# Returns information about the current VNC server
+#
+# Returns: @VncInfo
+# If VNC support is not compiled in, FeatureDisabled
+#
+# Since: 0.14.0
+##
+{ 'command': 'query-vnc', 'returns': 'VncInfo' }
+
+##
+# @SpiceChannel
+#
+# Information about a SPICE client channel.
+#
+# @host: The host name of the client. QEMU tries to resolve this to a DNS name
+# when possible.
+#
+# @family: 'ipv6' if the client is connected via IPv6 and TCP
+# 'ipv4' if the client is connected via IPv4 and TCP
+# 'unix' if the client is connected via a unix domain socket
+# 'unknown' otherwise
+#
+# @port: The client's port number.
+#
+# @connection-id: SPICE connection id number. All channels with the same id
+# belong to the same SPICE session.
+#
+# @connection-type: SPICE channel type number. "1" is the main control
+# channel, filter for this one if you want to track spice
+# sessions only
+#
+# @channel-id: SPICE channel ID number. Usually "0", might be different when
+# multiple channels of the same type exist, such as multiple
+# display channels in a multihead setup
+#
+# @tls: true if the channel is encrypted, false otherwise.
+#
+# Since: 0.14.0
+##
+{ 'type': 'SpiceChannel',
+ 'data': {'host': 'str', 'family': 'str', 'port': 'str',
+ 'connection-id': 'int', 'channel-type': 'int', 'channel-id': 'int',
+ 'tls': 'bool'} }
+
+##
+# @SpiceInfo
+#
+# Information about the SPICE session.
+#
+# @enabled: true if the SPICE server is enabled, false otherwise
+#
+# @host: #optional The hostname the SPICE server is bound to. This depends on
+# the name resolution on the host and may be an IP address.
+#
+# @port: #optional The SPICE server's port number.
+#
+# @compiled-version: #optional SPICE server version.
+#
+# @tls-port: #optional The SPICE server's TLS port number.
+#
+# @auth: #optional the current authentication type used by the server
+# 'none' if no authentication is being used
+# 'spice' uses SASL or direct TLS authentication, depending on command
+# line options
+#
+# @channels: a list of @SpiceChannel for each active spice channel
+#
+# Since: 0.14.0
+##
+{ 'type': 'SpiceInfo',
+ 'data': {'enabled': 'bool', '*host': 'str', '*port': 'int',
+ '*tls-port': 'int', '*auth': 'str', '*compiled-version': 'str',
+ '*channels': ['SpiceChannel']} }
+
+##
+# @query-spice
+#
+# Returns information about the current SPICE server
+#
+# Returns: @SpiceInfo
+#
+# Since: 0.14.0
+##
+{ 'command': 'query-spice', 'returns': 'SpiceInfo' }
+
+##
+# @BalloonInfo:
+#
+# Information about the guest balloon device.
+#
+# @actual: the number of bytes the balloon currently contains
+#
+# @mem_swapped_in: #optional number of pages swapped in within the guest
+#
+# @mem_swapped_out: #optional number of pages swapped out within the guest
+#
+# @major_page_faults: #optional number of major page faults within the guest
+#
+# @minor_page_faults: #optional number of minor page faults within the guest
+#
+# @free_mem: #optional amount of memory (in bytes) free in the guest
+#
+# @total_mem: #optional amount of memory (in bytes) visible to the guest
+#
+# Since: 0.14.0
+#
+# Notes: all current versions of QEMU do not fill out optional information in
+# this structure.
+##
+{ 'type': 'BalloonInfo',
+ 'data': {'actual': 'int', '*mem_swapped_in': 'int',
+ '*mem_swapped_out': 'int', '*major_page_faults': 'int',
+ '*minor_page_faults': 'int', '*free_mem': 'int',
+ '*total_mem': 'int'} }
+
+##
+# @query-balloon:
+#
+# Return information about the balloon device.
+#
+# Returns: @BalloonInfo on success
+# If the balloon driver is enabled but not functional because the KVM
+# kernel module cannot support it, KvmMissingCap
+# If no balloon device is present, DeviceNotActive
+#
+# Since: 0.14.0
+##
+{ 'command': 'query-balloon', 'returns': 'BalloonInfo' }
+
+##
+# @PciMemoryRange:
+#
+# A PCI device memory region
+#
+# @base: the starting address (guest physical)
+#
+# @limit: the ending address (guest physical)
+#
+# Since: 0.14.0
+##
+{ 'type': 'PciMemoryRange', 'data': {'base': 'int', 'limit': 'int'} }
+
+##
+# @PciMemoryRegion
+#
+# Information about a PCI device I/O region.
+#
+# @bar: the index of the Base Address Register for this region
+#
+# @type: 'io' if the region is a PIO region
+# 'memory' if the region is a MMIO region
+#
+# @prefetch: #optional if @type is 'memory', true if the memory is prefetchable
+#
+# @mem_type_64: #optional if @type is 'memory', true if the BAR is 64-bit
+#
+# Since: 0.14.0
+##
+{ 'type': 'PciMemoryRegion',
+ 'data': {'bar': 'int', 'type': 'str', 'address': 'int', 'size': 'int',
+ '*prefetch': 'bool', '*mem_type_64': 'bool' } }
+
+##
+# @PciBridgeInfo:
+#
+# Information about a PCI Bridge device
+#
+# @bus.number: primary bus interface number. This should be the number of the
+# bus the device resides on.
+#
+# @bus.secondary: secondary bus interface number. This is the number of the
+# main bus for the bridge
+#
+# @bus.subordinate: This is the highest number bus that resides below the
+# bridge.
+#
+# @bus.io_range: The PIO range for all devices on this bridge
+#
+# @bus.memory_range: The MMIO range for all devices on this bridge
+#
+# @bus.prefetchable_range: The range of prefetchable MMIO for all devices on
+# this bridge
+#
+# @devices: a list of @PciDeviceInfo for each device on this bridge
+#
+# Since: 0.14.0
+##
+{ 'type': 'PciBridgeInfo',
+ 'data': {'bus': { 'number': 'int', 'secondary': 'int', 'subordinate': 'int',
+ 'io_range': 'PciMemoryRange',
+ 'memory_range': 'PciMemoryRange',
+ 'prefetchable_range': 'PciMemoryRange' },
+ '*devices': ['PciDeviceInfo']} }
+
+##
+# @PciDeviceInfo:
+#
+# Information about a PCI device
+#
+# @bus: the bus number of the device
+#
+# @slot: the slot the device is located in
+#
+# @function: the function of the slot used by the device
+#
+# @class_info.desc: #optional a string description of the device's class
+#
+# @class_info.class: the class code of the device
+#
+# @id.device: the PCI device id
+#
+# @id.vendor: the PCI vendor id
+#
+# @irq: #optional if an IRQ is assigned to the device, the IRQ number
+#
+# @qdev_id: the device name of the PCI device
+#
+# @pci_bridge: if the device is a PCI bridge, the bridge information
+#
+# @regions: a list of the PCI I/O regions associated with the device
+#
+# Notes: the contents of @class_info.desc are not stable and should only be
+# treated as informational.
+#
+# Since: 0.14.0
+##
+{ 'type': 'PciDeviceInfo',
+ 'data': {'bus': 'int', 'slot': 'int', 'function': 'int',
+ 'class_info': {'*desc': 'str', 'class': 'int'},
+ 'id': {'device': 'int', 'vendor': 'int'},
+ '*irq': 'int', 'qdev_id': 'str', '*pci_bridge': 'PciBridgeInfo',
+ 'regions': ['PciMemoryRegion']} }
+
+##
+# @PciInfo:
+#
+# Information about a PCI bus
+#
+# @bus: the bus index
+#
+# @devices: a list of devices on this bus
+#
+# Since: 0.14.0
+##
+{ 'type': 'PciInfo', 'data': {'bus': 'int', 'devices': ['PciDeviceInfo']} }
+
+##
+# @query-pci:
+#
+# Return information about the PCI bus topology of the guest.
+#
+# Returns: a list of @PciInfo for each PCI bus
+#
+# Since: 0.14.0
+##
+{ 'command': 'query-pci', 'returns': ['PciInfo'] }
+
+##
+# @BlockJobInfo:
+#
+# Information about a long-running block device operation.
+#
+# @type: the job type ('stream' for image streaming)
+#
+# @device: the block device name
+#
+# @len: the maximum progress value
+#
+# @offset: the current progress value
+#
+# @speed: the rate limit, bytes per second
+#
+# Since: 1.1
+##
+{ 'type': 'BlockJobInfo',
+ 'data': {'type': 'str', 'device': 'str', 'len': 'int',
+ 'offset': 'int', 'speed': 'int'} }
+
+##
+# @query-block-jobs:
+#
+# Return information about long-running block device operations.
+#
+# Returns: a list of @BlockJobInfo for each active block job
+#
+# Since: 1.1
+##
+{ 'command': 'query-block-jobs', 'returns': ['BlockJobInfo'] }
+
+##
+# @quit:
+#
+# This command will cause the QEMU process to exit gracefully. While every
+# attempt is made to send the QMP response before terminating, this is not
+# guaranteed. When using this interface, a premature EOF would not be
+# unexpected.
+#
+# Since: 0.14.0
+##
+{ 'command': 'quit' }
+
+##
+# @stop:
+#
+# Stop all guest VCPU execution.
+#
+# Since: 0.14.0
+#
+# Notes: This function will succeed even if the guest is already in the stopped
+# state
+##
+{ 'command': 'stop' }
+
+##
+# @system_reset:
+#
+# Performs a hard reset of a guest.
+#
+# Since: 0.14.0
+##
+{ 'command': 'system_reset' }
+
+##
+# @system_powerdown:
+#
+# Requests that a guest perform a powerdown operation.
+#
+# Since: 0.14.0
+#
+# Notes: A guest may or may not respond to this command. This command
+# returning does not indicate that a guest has accepted the request or
+# that it has shut down. Many guests will respond to this command by
+# prompting the user in some way.
+##
+{ 'command': 'system_powerdown' }
+
+##
+# @cpu:
+#
+# This command is a nop that is only provided for the purposes of compatibility.
+#
+# Since: 0.14.0
+#
+# Notes: Do not use this command.
+##
+{ 'command': 'cpu', 'data': {'index': 'int'} }
+
+##
+# @memsave:
+#
+# Save a portion of guest memory to a file.
+#
+# @val: the virtual address of the guest to start from
+#
+# @size: the size of memory region to save
+#
+# @filename: the file to save the memory to as binary data
+#
+# @cpu-index: #optional the index of the virtual CPU to use for translating the
+# virtual address (defaults to CPU 0)
+#
+# Returns: Nothing on success
+# If @cpu is not a valid VCPU, InvalidParameterValue
+# If @filename cannot be opened, OpenFileFailed
+# If an I/O error occurs while writing the file, IOError
+#
+# Since: 0.14.0
+#
+# Notes: Errors were not reliably returned until 1.1
+##
+{ 'command': 'memsave',
+ 'data': {'val': 'int', 'size': 'int', 'filename': 'str', '*cpu-index': 'int'} }
+
+##
+# @pmemsave:
+#
+# Save a portion of guest physical memory to a file.
+#
+# @val: the physical address of the guest to start from
+#
+# @size: the size of memory region to save
+#
+# @filename: the file to save the memory to as binary data
+#
+# Returns: Nothing on success
+# If @filename cannot be opened, OpenFileFailed
+# If an I/O error occurs while writing the file, IOError
+#
+# Since: 0.14.0
+#
+# Notes: Errors were not reliably returned until 1.1
+##
+{ 'command': 'pmemsave',
+ 'data': {'val': 'int', 'size': 'int', 'filename': 'str'} }
+
+##
+# @cont:
+#
+# Resume guest VCPU execution.
+#
+# Since: 0.14.0
+#
+# Returns: If successful, nothing
+# If the QEMU is waiting for an incoming migration, MigrationExpected
+# If QEMU was started with an encrypted block device and a key has
+# not yet been set, DeviceEncrypted.
+#
+# Notes: This command will succeed if the guest is currently running.
+##
+{ 'command': 'cont' }
+
+##
+# @system_wakeup:
+#
+# Wakeup guest from suspend. Does nothing in case the guest isn't suspended.
+#
+# Since: 1.1
+#
+# Returns: nothing.
+##
+{ 'command': 'system_wakeup' }
+
+##
+# @inject-nmi:
+#
+# Injects an Non-Maskable Interrupt into all guest's VCPUs.
+#
+# Returns: If successful, nothing
+# If the Virtual Machine doesn't support NMI injection, Unsupported
+#
+# Since: 0.14.0
+#
+# Notes: Only x86 Virtual Machines support this command.
+##
+{ 'command': 'inject-nmi' }
+
+##
+# @set_link:
+#
+# Sets the link status of a virtual network adapter.
+#
+# @name: the device name of the virtual network adapter
+#
+# @up: true to set the link status to be up
+#
+# Returns: Nothing on success
+# If @name is not a valid network device, DeviceNotFound
+#
+# Since: 0.14.0
+#
+# Notes: Not all network adapters support setting link status. This command
+# will succeed even if the network adapter does not support link status
+# notification.
+##
+{ 'command': 'set_link', 'data': {'name': 'str', 'up': 'bool'} }
+
+##
+# @block_passwd:
+#
+# This command sets the password of a block device that has not been open
+# with a password and requires one.
+#
+# The two cases where this can happen are a block device is created through
+# QEMU's initial command line or a block device is changed through the legacy
+# @change interface.
+#
+# In the event that the block device is created through the initial command
+# line, the VM will start in the stopped state regardless of whether '-S' is
+# used. The intention is for a management tool to query the block devices to
+# determine which ones are encrypted, set the passwords with this command, and
+# then start the guest with the @cont command.
+#
+# @device: the name of the device to set the password on
+#
+# @password: the password to use for the device
+#
+# Returns: nothing on success
+# If @device is not a valid block device, DeviceNotFound
+# If @device is not encrypted, DeviceNotEncrypted
+# If @password is not valid for this device, InvalidPassword
+#
+# Notes: Not all block formats support encryption and some that do are not
+# able to validate that a password is correct. Disk corruption may
+# occur if an invalid password is specified.
+#
+# Since: 0.14.0
+##
+{ 'command': 'block_passwd', 'data': {'device': 'str', 'password': 'str'} }
+
+##
+# @balloon:
+#
+# Request the balloon driver to change its balloon size.
+#
+# @value: the target size of the balloon in bytes
+#
+# Returns: Nothing on success
+# If the balloon driver is enabled but not functional because the KVM
+# kernel module cannot support it, KvmMissingCap
+# If no balloon device is present, DeviceNotActive
+#
+# Notes: This command just issues a request to the guest. When it returns,
+# the balloon size may not have changed. A guest can change the balloon
+# size independent of this command.
+#
+# Since: 0.14.0
+##
+{ 'command': 'balloon', 'data': {'value': 'int'} }
+
+##
+# @block_resize
+#
+# Resize a block image while a guest is running.
+#
+# @device: the name of the device to get the image resized
+#
+# @size: new image size in bytes
+#
+# Returns: nothing on success
+# If @device is not a valid block device, DeviceNotFound
+# If @size is negative, InvalidParameterValue
+# If the block device has no medium inserted, DeviceHasNoMedium
+# If the block device does not support resize, Unsupported
+# If the block device is read-only, DeviceIsReadOnly
+# If a long-running operation is using the device, DeviceInUse
+#
+# Since: 0.14.0
+##
+{ 'command': 'block_resize', 'data': { 'device': 'str', 'size': 'int' }}
+
+##
+# @NewImageMode
+#
+# An enumeration that tells QEMU how to set the backing file path in
+# a new image file.
+#
+# @existing: QEMU should look for an existing image file.
+#
+# @absolute-paths: QEMU should create a new image with absolute paths
+# for the backing file.
+#
+# Since: 1.1
+##
+{ 'enum': 'NewImageMode'
+ 'data': [ 'existing', 'absolute-paths' ] }
+
+##
+# @BlockdevSnapshot
+#
+# @device: the name of the device to generate the snapshot from.
+#
+# @snapshot-file: the target of the new image. A new file will be created.
+#
+# @format: #optional the format of the snapshot image, default is 'qcow2'.
+#
+# @mode: #optional whether and how QEMU should create a new image, default is
+# 'absolute-paths'.
+##
+{ 'type': 'BlockdevSnapshot',
+ 'data': { 'device': 'str', 'snapshot-file': 'str', '*format': 'str',
+ '*mode': 'NewImageMode' } }
+
+##
+# @BlockdevAction
+#
+# A discriminated record of operations that can be performed with
+# @transaction.
+##
+{ 'union': 'BlockdevAction',
+ 'data': {
+ 'blockdev-snapshot-sync': 'BlockdevSnapshot',
+ } }
+
+##
+# @transaction
+#
+# Atomically operate on a group of one or more block devices. If
+# any operation fails, then the entire set of actions will be
+# abandoned and the appropriate error returned. The only operation
+# supported is currently blockdev-snapshot-sync.
+#
+# List of:
+# @BlockdevAction: information needed for the device snapshot
+#
+# Returns: nothing on success
+# If @device is not a valid block device, DeviceNotFound
+# If @device is busy, DeviceInUse will be returned
+# If @snapshot-file can't be created, OpenFileFailed
+# If @snapshot-file can't be opened, OpenFileFailed
+# If @format is invalid, InvalidBlockFormat
+#
+# Note: The transaction aborts on the first failure. Therefore, there will
+# be only one device or snapshot file returned in an error condition, and
+# subsequent actions will not have been attempted.
+#
+# Since 1.1
+##
+{ 'command': 'transaction',
+ 'data': { 'actions': [ 'BlockdevAction' ] } }
+
+##
+# @blockdev-snapshot-sync
+#
+# Generates a synchronous snapshot of a block device.
+#
+# @device: the name of the device to generate the snapshot from.
+#
+# @snapshot-file: the target of the new image. If the file exists, or if it
+# is a device, the snapshot will be created in the existing
+# file/device. If does not exist, a new file will be created.
+#
+# @format: #optional the format of the snapshot image, default is 'qcow2'.
+#
+# @mode: #optional whether and how QEMU should create a new image, default is
+# 'absolute-paths'.
+#
+# Returns: nothing on success
+# If @device is not a valid block device, DeviceNotFound
+# If @snapshot-file can't be opened, OpenFileFailed
+# If @format is invalid, InvalidBlockFormat
+#
+# Since 0.14.0
+##
+{ 'command': 'blockdev-snapshot-sync',
+ 'data': { 'device': 'str', 'snapshot-file': 'str', '*format': 'str',
+ '*mode': 'NewImageMode'} }
+
+##
+# @human-monitor-command:
+#
+# Execute a command on the human monitor and return the output.
+#
+# @command-line: the command to execute in the human monitor
+#
+# @cpu-index: #optional The CPU to use for commands that require an implicit CPU
+#
+# Returns: the output of the command as a string
+#
+# Since: 0.14.0
+#
+# Notes: This command only exists as a stop-gap. It's use is highly
+# discouraged. The semantics of this command are not guaranteed.
+#
+# Known limitations:
+#
+# o This command is stateless, this means that commands that depend
+# on state information (such as getfd) might not work
+#
+# o Commands that prompt the user for data (eg. 'cont' when the block
+# device is encrypted) don't currently work
+##
+{ 'command': 'human-monitor-command',
+ 'data': {'command-line': 'str', '*cpu-index': 'int'},
+ 'returns': 'str' }
+
+##
+# @migrate_cancel
+#
+# Cancel the current executing migration process.
+#
+# Returns: nothing on success
+#
+# Notes: This command succeeds even if there is no migration process running.
+#
+# Since: 0.14.0
+##
+{ 'command': 'migrate_cancel' }
+
+##
+# @migrate_set_downtime
+#
+# Set maximum tolerated downtime for migration.
+#
+# @value: maximum downtime in seconds
+#
+# Returns: nothing on success
+#
+# Since: 0.14.0
+##
+{ 'command': 'migrate_set_downtime', 'data': {'value': 'number'} }
+
+##
+# @migrate_set_speed
+#
+# Set maximum speed for migration.
+#
+# @value: maximum speed in bytes.
+#
+# Returns: nothing on success
+#
+# Notes: A value lesser than zero will be automatically round up to zero.
+#
+# Since: 0.14.0
+##
+{ 'command': 'migrate_set_speed', 'data': {'value': 'int'} }
+
+##
+# @ObjectPropertyInfo:
+#
+# @name: the name of the property
+#
+# @type: the type of the property. This will typically come in one of four
+# forms:
+#
+# 1) A primitive type such as 'u8', 'u16', 'bool', 'str', or 'double'.
+# These types are mapped to the appropriate JSON type.
+#
+# 2) A legacy type in the form 'legacy<subtype>' where subtype is the
+# legacy qdev typename. These types are always treated as strings.
+#
+# 3) A child type in the form 'child<subtype>' where subtype is a qdev
+# device type name. Child properties create the composition tree.
+#
+# 4) A link type in the form 'link<subtype>' where subtype is a qdev
+# device type name. Link properties form the device model graph.
+#
+# Since: 1.1
+#
+# Notes: This type is experimental. Its syntax may change in future releases.
+##
+{ 'type': 'ObjectPropertyInfo',
+ 'data': { 'name': 'str', 'type': 'str' } }
+
+##
+# @qom-list:
+#
+# This command will list any properties of a object given a path in the object
+# model.
+#
+# @path: the path within the object model. See @qom-get for a description of
+# this parameter.
+#
+# Returns: a list of @ObjectPropertyInfo that describe the properties of the
+# object.
+#
+# Since: 1.1
+#
+# Notes: This command is experimental. It's syntax may change in future
+# releases.
+##
+{ 'command': 'qom-list',
+ 'data': { 'path': 'str' },
+ 'returns': [ 'ObjectPropertyInfo' ] }
+
+##
+# @qom-get:
+#
+# This command will get a property from a object model path and return the
+# value.
+#
+# @path: The path within the object model. There are two forms of supported
+# paths--absolute and partial paths.
+#
+# Absolute paths are derived from the root object and can follow child<>
+# or link<> properties. Since they can follow link<> properties, they
+# can be arbitrarily long. Absolute paths look like absolute filenames
+# and are prefixed with a leading slash.
+#
+# Partial paths look like relative filenames. They do not begin
+# with a prefix. The matching rules for partial paths are subtle but
+# designed to make specifying objects easy. At each level of the
+# composition tree, the partial path is matched as an absolute path.
+# The first match is not returned. At least two matches are searched
+# for. A successful result is only returned if only one match is
+# found. If more than one match is found, a flag is return to
+# indicate that the match was ambiguous.
+#
+# @property: The property name to read
+#
+# Returns: The property value. The type depends on the property type. legacy<>
+# properties are returned as #str. child<> and link<> properties are
+# returns as #str pathnames. All integer property types (u8, u16, etc)
+# are returned as #int.
+#
+# Since: 1.1
+#
+# Notes: This command is experimental and may change syntax in future releases.
+##
+{ 'command': 'qom-get',
+ 'data': { 'path': 'str', 'property': 'str' },
+ 'returns': 'visitor',
+ 'gen': 'no' }
+
+##
+# @qom-set:
+#
+# This command will set a property from a object model path.
+#
+# @path: see @qom-get for a description of this parameter
+#
+# @property: the property name to set
+#
+# @value: a value who's type is appropriate for the property type. See @qom-get
+# for a description of type mapping.
+#
+# Since: 1.1
+#
+# Notes: This command is experimental and may change syntax in future releases.
+##
+{ 'command': 'qom-set',
+ 'data': { 'path': 'str', 'property': 'str', 'value': 'visitor' },
+ 'gen': 'no' }
+
+##
+# @set_password:
+#
+# Sets the password of a remote display session.
+#
+# @protocol: `vnc' to modify the VNC server password
+# `spice' to modify the Spice server password
+#
+# @password: the new password
+#
+# @connected: #optional how to handle existing clients when changing the
+# password. If nothing is specified, defaults to `keep'
+# `fail' to fail the command if clients are connected
+# `disconnect' to disconnect existing clients
+# `keep' to maintain existing clients
+#
+# Returns: Nothing on success
+# If Spice is not enabled, DeviceNotFound
+# If @protocol does not support connected, InvalidParameter
+# If @protocol is invalid, InvalidParameter
+# If any other error occurs, SetPasswdFailed
+#
+# Notes: If VNC is not enabled, SetPasswdFailed is returned.
+#
+# Since: 0.14.0
+##
+{ 'command': 'set_password',
+ 'data': {'protocol': 'str', 'password': 'str', '*connected': 'str'} }
+
+##
+# @expire_password:
+#
+# Expire the password of a remote display server.
+#
+# @protocol: the name of the remote display protocol `vnc' or `spice'
+#
+# @time: when to expire the password.
+# `now' to expire the password immediately
+# `never' to cancel password expiration
+# `+INT' where INT is the number of seconds from now (integer)
+# `INT' where INT is the absolute time in seconds
+#
+# Returns: Nothing on success
+# If @protocol is `spice' and Spice is not active, DeviceNotFound
+# If an error occurs setting password expiration, SetPasswdFailed
+# If @protocol is not `spice' or 'vnc', InvalidParameter
+#
+# Since: 0.14.0
+#
+# Notes: Time is relative to the server and currently there is no way to
+# coordinate server time with client time. It is not recommended to
+# use the absolute time version of the @time parameter unless you're
+# sure you are on the same machine as the QEMU instance.
+##
+{ 'command': 'expire_password', 'data': {'protocol': 'str', 'time': 'str'} }
+
+##
+# @eject:
+#
+# Ejects a device from a removable drive.
+#
+# @device: The name of the device
+#
+# @force: @optional If true, eject regardless of whether the drive is locked.
+# If not specified, the default value is false.
+#
+# Returns: Nothing on success
+# If @device is not a valid block device, DeviceNotFound
+# If @device is not removable and @force is false, DeviceNotRemovable
+# If @force is false and @device is locked, DeviceLocked
+#
+# Notes: Ejecting a device will no media results in success
+#
+# Since: 0.14.0
+##
+{ 'command': 'eject', 'data': {'device': 'str', '*force': 'bool'} }
+
+##
+# @change-vnc-password:
+#
+# Change the VNC server password.
+#
+# @target: the new password to use with VNC authentication
+#
+# Since: 1.1
+#
+# Notes: An empty password in this command will set the password to the empty
+# string. Existing clients are unaffected by executing this command.
+##
+{ 'command': 'change-vnc-password', 'data': {'password': 'str'} }
+
+##
+# @change:
+#
+# This command is multiple commands multiplexed together.
+#
+# @device: This is normally the name of a block device but it may also be 'vnc'.
+# when it's 'vnc', then sub command depends on @target
+#
+# @target: If @device is a block device, then this is the new filename.
+# If @device is 'vnc', then if the value 'password' selects the vnc
+# change password command. Otherwise, this specifies a new server URI
+# address to listen to for VNC connections.
+#
+# @arg: If @device is a block device, then this is an optional format to open
+# the device with.
+# If @device is 'vnc' and @target is 'password', this is the new VNC
+# password to set. If this argument is an empty string, then no future
+# logins will be allowed.
+#
+# Returns: Nothing on success.
+# If @device is not a valid block device, DeviceNotFound
+# If @format is not a valid block format, InvalidBlockFormat
+# If the new block device is encrypted, DeviceEncrypted. Note that
+# if this error is returned, the device has been opened successfully
+# and an additional call to @block_passwd is required to set the
+# device's password. The behavior of reads and writes to the block
+# device between when these calls are executed is undefined.
+#
+# Notes: It is strongly recommended that this interface is not used especially
+# for changing block devices.
+#
+# Since: 0.14.0
+##
+{ 'command': 'change',
+ 'data': {'device': 'str', 'target': 'str', '*arg': 'str'} }
+
+##
+# @block_set_io_throttle:
+#
+# Change I/O throttle limits for a block drive.
+#
+# @device: The name of the device
+#
+# @bps: total throughput limit in bytes per second
+#
+# @bps_rd: read throughput limit in bytes per second
+#
+# @bps_wr: write throughput limit in bytes per second
+#
+# @iops: total I/O operations per second
+#
+# @ops_rd: read I/O operations per second
+#
+# @iops_wr: write I/O operations per second
+#
+# Returns: Nothing on success
+# If @device is not a valid block device, DeviceNotFound
+# If the argument combination is invalid, InvalidParameterCombination
+#
+# Since: 1.1
+##
+{ 'command': 'block_set_io_throttle',
+ 'data': { 'device': 'str', 'bps': 'int', 'bps_rd': 'int', 'bps_wr': 'int',
+ 'iops': 'int', 'iops_rd': 'int', 'iops_wr': 'int' } }
+
+# @block_stream:
+#
+# Copy data from a backing file into a block device.
+#
+# The block streaming operation is performed in the background until the entire
+# backing file has been copied. This command returns immediately once streaming
+# has started. The status of ongoing block streaming operations can be checked
+# with query-block-jobs. The operation can be stopped before it has completed
+# using the block_job_cancel command.
+#
+# If a base file is specified then sectors are not copied from that base file and
+# its backing chain. When streaming completes the image file will have the base
+# file as its backing file. This can be used to stream a subset of the backing
+# file chain instead of flattening the entire image.
+#
+# On successful completion the image file is updated to drop the backing file
+# and the BLOCK_JOB_COMPLETED event is emitted.
+#
+# @device: the device name
+#
+# @base: #optional the common backing file name
+#
+# Returns: Nothing on success
+# If streaming is already active on this device, DeviceInUse
+# If @device does not exist, DeviceNotFound
+# If image streaming is not supported by this device, NotSupported
+# If @base does not exist, BaseNotFound
+#
+# Since: 1.1
+##
+{ 'command': 'block_stream', 'data': { 'device': 'str', '*base': 'str' } }
+
+##
+# @block_job_set_speed:
+#
+# Set maximum speed for a background block operation.
+#
+# This command can only be issued when there is an active block job.
+#
+# Throttling can be disabled by setting the speed to 0.
+#
+# @device: the device name
+#
+# @value: the maximum speed, in bytes per second
+#
+# Returns: Nothing on success
+# If the job type does not support throttling, NotSupported
+# If streaming is not active on this device, DeviceNotActive
+#
+# Since: 1.1
+##
+{ 'command': 'block_job_set_speed',
+ 'data': { 'device': 'str', 'value': 'int' } }
+
+##
+# @block_job_cancel:
+#
+# Stop an active block streaming operation.
+#
+# This command returns immediately after marking the active block streaming
+# operation for cancellation. It is an error to call this command if no
+# operation is in progress.
+#
+# The operation will cancel as soon as possible and then emit the
+# BLOCK_JOB_CANCELLED event. Before that happens the job is still visible when
+# enumerated using query-block-jobs.
+#
+# The image file retains its backing file unless the streaming operation happens
+# to complete just as it is being cancelled.
+#
+# A new block streaming operation can be started at a later time to finish
+# copying all data from the backing file.
+#
+# @device: the device name
+#
+# Returns: Nothing on success
+# If streaming is not active on this device, DeviceNotActive
+# If cancellation already in progress, DeviceInUse
+#
+# Since: 1.1
+##
+{ 'command': 'block_job_cancel', 'data': { 'device': 'str' } }
+
+##
+# @ObjectTypeInfo:
+#
+# This structure describes a search result from @qom-list-types
+#
+# @name: the type name found in the search
+#
+# Since: 1.1
+#
+# Notes: This command is experimental and may change syntax in future releases.
+##
+{ 'type': 'ObjectTypeInfo',
+ 'data': { 'name': 'str' } }
+
+##
+# @qom-list-types:
+#
+# This command will return a list of types given search parameters
+#
+# @implements: if specified, only return types that implement this type name
+#
+# @abstract: if true, include abstract types in the results
+#
+# Returns: a list of @ObjectTypeInfo or an empty list if no results are found
+#
+# Since: 1.1
+#
+# Notes: This command is experimental and may change syntax in future releases.
+##
+{ 'command': 'qom-list-types',
+ 'data': { '*implements': 'str', '*abstract': 'bool' },
+ 'returns': [ 'ObjectTypeInfo' ] }
+
+##
+# @migrate
+#
+# Migrates the current running guest to another Virtual Machine.
+#
+# @uri: the Uniform Resource Identifier of the destination VM
+#
+# @blk: #optional do block migration (full disk copy)
+#
+# @inc: #optional incremental disk copy migration
+#
+# @detach: this argument exists only for compatibility reasons and
+# is ignored by QEMU
+#
+# Returns: nothing on success
+#
+# Since: 0.14.0
+##
+{ 'command': 'migrate',
+ 'data': {'uri': 'str', '*blk': 'bool', '*inc': 'bool', '*detach': 'bool' } }
+
+# @xen-save-devices-state:
+#
+# Save the state of all devices to file. The RAM and the block devices
+# of the VM are not saved by this command.
+#
+# @filename: the file to save the state of the devices to as binary
+# data. See xen-save-devices-state.txt for a description of the binary
+# format.
+#
+# Returns: Nothing on success
+# If @filename cannot be opened, OpenFileFailed
+# If an I/O error occurs while writing the file, IOError
+#
+# Since: 1.1
+##
+{ 'command': 'xen-save-devices-state', 'data': {'filename': 'str'} }
+
+##
+# @device_del:
+#
+# Remove a device from a guest
+#
+# @id: the name of the device
+#
+# Returns: Nothing on success
+# If @id is not a valid device, DeviceNotFound
+# If the device does not support unplug, BusNoHotplug
+#
+# Notes: When this command completes, the device may not be removed from the
+# guest. Hot removal is an operation that requires guest cooperation.
+# This command merely requests that the guest begin the hot removal
+# process.
+#
+# Since: 0.14.0
+##
+{ 'command': 'device_del', 'data': {'id': 'str'} }
projects / qemu.git / blobdiff