Calculate the divisor for the SCR (Serial Clock Rate), avoiding
that the SSP transmission rate can be greater than the device rate.
When the division between the SSP clock and the device rate generates
a reminder, we have to increment by one the divisor.
In this way the resulting SSP clock will never be greater than the
device SPI max frequency.
For example, with:
- ssp_clk = 50 MHz
- dev freq = 15 MHz
without this patch the SSP clock will be greater than 15 MHz:
- 25 MHz for PXA25x_SSP and CE4100_SSP
- 16,56 MHz for the others
Instead, with this patch, we have in both case an SSP clock of 12.5MHz,
so the max rate of the SPI device clock is respected.
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it> Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
sound/soc/fsl/imx-ssi.o: In function `imx_ssi_remove':
imx-ssi.c:(.text+0x28): undefined reference to `imx_pcm_fiq_exit'
sound/soc/fsl/imx-ssi.o: In function `imx_ssi_probe':
imx-ssi.c:(.text+0xa64): undefined reference to `imx_pcm_fiq_init'
The Kconfig warning is a result of the symbol being defined inside of
the "if SND_IMX_SOC" block, and is otherwise harmless. The link error
is more tricky and happens with SND_SOC_IMX_SSI=y, which may or may not
imply FIQ support. However, if SND_SOC_FSL_SSI is set to =m at the same
time, that selects SND_SOC_IMX_PCM_FIQ as a loadable module dependency,
which then causes a link failure from imx-ssi.
The solution here is to make SND_SOC_IMX_PCM_FIQ built-in whenever
one of its potential users is built-in.
Fixes: ff40260f79dc ("ASoC: fsl: refine DMA/FIQ dependencies") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Nest hardware counter memory resides in a per-chip reserve-memory.
During nest_imc_event_init(), chip-id of the event-cpu is considered to
calculate the base memory addresss for that cpu. Return, proper error
condition if the chip_id calculated is invalid.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: 885dcd709ba91 ("powerpc/perf: Add nest IMC PMU support") Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com> Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If the hdmi codec startup fails, it should clear the current_substream
pointer to free the device. This is properly done for the audio_startup()
callback but for snd_pcm_hw_constraint_eld().
Make sure the pointer cleared if an error is reported.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/pinctrl/zte/pinctrl-zx.c:415:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 407, but without a corresponding object release within this function.
./drivers/pinctrl/zte/pinctrl-zx.c:422:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 407, but without a corresponding object release within this function.
./drivers/pinctrl/zte/pinctrl-zx.c:436:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 407, but without a corresponding object release within this function.
./drivers/pinctrl/zte/pinctrl-zx.c:444:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 407, but without a corresponding object release within this function.
./drivers/pinctrl/zte/pinctrl-zx.c:448:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 407, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Jun Nie <jun.nie@linaro.org> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: linux-gpio@vger.kernel.org Cc: linux-kernel@vger.kernel.org Acked-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
GCC 8 contains a number of new warnings as well as enhancements to existing
checkers. The warning - Wstringop-truncation - warns for calls to bounded
string manipulation functions such as strncat, strncpy, and stpncpy that
may either truncate the copied string or leave the destination unchanged.
In our case the destination string length (32 bytes) is much shorter than
the source string (64 bytes) which causes this warning to show up. In
general the destination has to be at least a byte larger than the length
of the source string with strncpy for this warning not to showup.
This can be easily fixed by using strlcpy instead which already does the
truncation to the string. Documentation for this function can be
found here:
In device probe(), of_dma_controller_register() registers DMA controller.
But when driver is removed, this is not freed. During driver reload this
results in data abort and kernel panic. Add of_dma_controller_free() in
driver remove path to fix the issue.
Fixes: f46b195799b5 ("dmaengine: tegra-adma: Add support for Tegra210 ADMA") Signed-off-by: Sameer Pujar <spujar@nvidia.com> Reviewed-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When build perf for ARC recently, there was a build failure due to lack
of __NR_bpf.
| Auto-detecting system features:
|
| ... get_cpuid: [ OFF ]
| ... bpf: [ on ]
|
| # error __NR_bpf not defined. libbpf does not support your arch.
^~~~~
| bpf.c: In function 'sys_bpf':
| bpf.c:66:17: error: '__NR_bpf' undeclared (first use in this function)
| return syscall(__NR_bpf, cmd, attr, size);
| ^~~~~~~~
| sys_bpf
The SD Physical Layer Spec says the following: Since the SD Memory Card
shall support at least the two bus modes 1-bit or 4-bit width, then any SD
Card shall set at least bits 0 and 2 (SD_BUS_WIDTH="0101").
This change verifies the card has specified a bus width.
AMD SDHC Device 7806 can get into a bad state after a card disconnect
where anything transferred via the DATA lines will always result in a
zero filled buffer. Currently the driver will continue without error if
the HC is in this condition. A block device will be created, but reading
from it will result in a zero buffer. This makes it seem like the SD
device has been erased, when in actuality the data is never getting
copied from the DATA lines to the data buffer.
SCR is the first command in the SD initialization sequence that uses the
DATA lines. By checking that the response was invalid, we can abort
mounting the card.
This patch has to do with the life cycle of glocks and buffers. When
gfs2 metadata or journaled data is queued to be written, a gfs2_bufdata
object is assigned to track the buffer, and that is queued to various
lists, including the glock's gl_ail_list to indicate it's on the active
items list. Once the page associated with the buffer has been written,
it is removed from the ail list, but its life isn't over until a revoke
has been successfully written.
So after the block is written, its bufdata object is moved from the
glock's gl_ail_list to a file-system-wide list of pending revokes,
sd_log_le_revoke. At that point the glock still needs to track how many
revokes it contributed to that list (in gl_revokes) so that things like
glock go_sync can ensure all the metadata has been not only written, but
also revoked before the glock is granted to a different node. This is
to guarantee journal replay doesn't replay the block once the glock has
been granted to another node.
Ross Lagerwall recently discovered a race in which an inode could be
evicted, and its glock freed after its ail list had been synced, but
while it still had unwritten revokes on the sd_log_le_revoke list. The
evict decremented the glock reference count to zero, which allowed the
glock to be freed. After the revoke was written, function
revoke_lo_after_commit tried to adjust the glock's gl_revokes counter
and clear its GLF_LFLUSH flag, at which time it referenced the freed
glock.
This patch fixes the problem by incrementing the glock reference count
in gfs2_add_revoke when the glock's first bufdata object is moved from
the glock to the global revokes list. Later, when the glock's last such
bufdata object is freed, the reference count is decremented. This
guarantees that whichever process finishes last (the revoke writing or
the evict) will properly free the glock, and neither will reference the
glock after it has been freed.
Reported-by: Ross Lagerwall <ross.lagerwall@citrix.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since QP destruction frees memory, hfi1_wq should have the WQ_MEM_RECLAIM.
The hfi1_wq does not allocate memory with GFP_KERNEL or otherwise become
entangled with memory reclaim, so this flag is appropriate.
Fixes: 0a226edd203f ("staging/rdma/hfi1: Use parallel workqueue for SDMA engines") Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Actually we don't do anything with return value from
nfs_wait_client_init_complete in nfs_match_client, as a
consequence if we get a fatal signal and client is not
fully initialised, we'll loop to "again" label
This has been proven to cause soft lockups on some scenarios
(no-carrier but configured network interfaces)
Signed-off-by: Roberto Bergantinos Corpas <rbergant@redhat.com> Reviewed-by: Benjamin Coddington <bcodding@redhat.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Under certain conditions, lru_count may drop below zero resulting in
a large amount of log spam like this:
vmscan: shrink_slab: gfs2_dump_glock+0x3b0/0x630 [gfs2] \
negative objects to delete nr=-1
This happens as follows:
1) A glock is moved from lru_list to the dispose list and lru_count is
decremented.
2) The dispose function calls cond_resched() and drops the lru lock.
3) Another thread takes the lru lock and tries to add the same glock to
lru_list, checking if the glock is on an lru list.
4) It is on a list (actually the dispose list) and so it avoids
incrementing lru_count.
5) The glock is moved to lru_list.
5) The original thread doesn't dispose it because it has been re-added
to the lru list but the lru_count has still decreased by one.
Fix by checking if the LRU flag is set on the glock rather than checking
if the glock is on some list and rearrange the code so that the LRU flag
is added/removed precisely when the glock is added/removed from lru_list.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When building the erspan header for either v1 or v2, the eth_hdr()
does not point to the right inner packet's eth_hdr,
causing kasan report use-after-free and slab-out-of-bouds read.
The patch fixes the following syzkaller issues:
[1] BUG: KASAN: slab-out-of-bounds in erspan_xmit+0x22d4/0x2430 net/ipv4/ip_gre.c:735
[2] BUG: KASAN: slab-out-of-bounds in erspan_build_header+0x3bf/0x3d0 net/ipv4/ip_gre.c:698
[3] BUG: KASAN: use-after-free in erspan_xmit+0x22d4/0x2430 net/ipv4/ip_gre.c:735
[4] BUG: KASAN: use-after-free in erspan_build_header+0x3bf/0x3d0 net/ipv4/ip_gre.c:698
Syzbot has reported some issues with the locking assumptions made for
the multicast tt/tvlv worker: It was able to trigger the WARN_ON() in
batadv_mcast_mla_tt_retract() and batadv_mcast_mla_tt_add().
While hard/not reproduceable for us so far it seems that the
delayed_work_pending() we use might not be quite safe from reordering.
Therefore this patch adds an explicit, new spinlock to protect the
update of the mla_list and flags in bat_priv and then removes the
WARN_ON(delayed_work_pending()).
Reported-by: syzbot+83f2d54ec6b7e417e13f@syzkaller.appspotmail.com Reported-by: syzbot+050927a651272b145a5d@syzkaller.appspotmail.com Reported-by: syzbot+979ffc89b87309b1b94b@syzkaller.appspotmail.com Reported-by: syzbot+f9f3f388440283da2965@syzkaller.appspotmail.com Fixes: cbebd363b2e9 ("batman-adv: Use own timer for multicast TT and TVLV updates") Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
synchronize_rcu() is fine when the rcu callbacks only need
to free memory (kfree_rcu() or direct kfree() call rcu call backs)
__dev_map_entry_free() is a bit more complex, so we need to make
sure that call queued __dev_map_entry_free() callbacks have completed.
sysbot report:
BUG: KASAN: use-after-free in dev_map_flush_old kernel/bpf/devmap.c:365
[inline]
BUG: KASAN: use-after-free in __dev_map_entry_free+0x2a8/0x300
kernel/bpf/devmap.c:379
Read of size 8 at addr ffff8801b8da38c8 by task ksoftirqd/1/18
Memory state around the buggy address: ffff8801b8da3780: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb ffff8801b8da3800: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
> ffff8801b8da3880: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff8801b8da3900: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8801b8da3980: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
Fixes: 546ac1ffb70d ("bpf: add devmap, a map for storing net device references") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot+457d3e2ffbcf31aee5c0@syzkaller.appspotmail.com Acked-by: Toke Høiland-Jørgensen <toke@redhat.com> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In ssb_modinit, it does not fail SSB init when ssb_host_pcmcia_init failed,
however in ssb_modexit, ssb_host_pcmcia_exit calls pcmcia_unregister_driver
unconditionally, which may tigger a NULL pointer dereference issue as above.
Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: 399500da18f7 ("ssb: pick PCMCIA host code support from b43 driver") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
syzkaller reported crashes on kfree() called from
vivid_vid_cap_s_selection(). This looks like a simple typo, as
dev->bitmap_cap is allocated with vzalloc() throughout the file.
Fixes: ef834f7836ec0 ("[media] vivid: add the video capture and output
parts")
Signed-off-by: Alexander Potapenko <glider@google.com> Reported-by: Syzbot <syzbot+6c0effb5877f6b0344e2@syzkaller.appspotmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Memory state around the buggy address: ffff8881dc7adf00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff8881dc7adf80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff8881dc7ae000: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff8881dc7ae080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8881dc7ae100: fc fc fc fc fc fc fc fc 00 00 00 00 00 00 00 00
There are already cleanup handlings in serial_ir_init error path,
no need to call serial_ir_exit do it again in serial_ir_init_module,
otherwise will trigger a use-after-free issue.
Fixes: fa5dc29c1fcc ("[media] lirc_serial: move out of staging and rename to serial_ir") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Memory state around the buggy address: ffff8881f59a6a00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff8881f59a6a80: 00 00 00 00 00 00 00 00 00 00 fc fc fc fc fc fc
>ffff8881f59a6b00: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
^ ffff8881f59a6b80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8881f59a6c00: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
cpia2_init does not check return value of cpia2_init, if it failed
in usb_register_driver, there is already cleanup using driver_unregister.
No need call cpia2_usb_cleanup on module exit.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Qgroups will do the old roots lookup at delayed ref time, which could be
while walking down the extent root while running a delayed ref. This
should be fine, except we specifically lock eb's in the backref walking
code irrespective of path->skip_locking, which deadlocks the system.
Fix up the backref code to honor path->skip_locking, nobody will be
modifying the commit_root when we're searching so it's completely safe
to do.
This happens since fb235dc06fac ("btrfs: qgroup: Move half of the qgroup
accounting time out of commit trans"), kernel may lockup with quota
enabled.
There is one backref trace triggered by snapshot dropping along with
write operation in the source subvolume. The example can be reliably
reproduced:
When dropping snapshots with qgroup enabled, we will trigger backref
walk.
However such backref walk at that timing is pretty dangerous, as if one
of the parent nodes get WRITE locked by other thread, we could cause a
dead lock.
For example:
FS 260 FS 261 (Dropped)
node A node B
/ \ / \
node C node D node E
/ \ / \ / \
leaf F|leaf G|leaf H|leaf I|leaf J|leaf K
The lock sequence would be:
Thread A (cleaner) | Thread B (other writer)
-----------------------------------------------------------------------
write_lock(B) |
write_lock(D) |
^^^ called by walk_down_tree() |
| write_lock(A)
| write_lock(D) << Stall
read_lock(H) << for backref walk |
read_lock(D) << lock owner is |
the same thread A |
so read lock is OK |
read_lock(A) << Stall |
So thread A hold write lock D, and needs read lock A to unlock.
While thread B holds write lock A, while needs lock D to unlock.
This will cause a deadlock.
This is not only limited to snapshot dropping case. As the backref
walk, even only happens on commit trees, is breaking the normal top-down
locking order, makes it deadlock prone.
Fixes: fb235dc06fac ("btrfs: qgroup: Move half of the qgroup accounting time out of commit trans") CC: stable@vger.kernel.org # 4.14+ Reported-and-tested-by: David Sterba <dsterba@suse.com> Reported-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: Filipe Manana <fdmanana@suse.com>
[ rebase to latest branch and fix lock assert bug in btrfs/007 ]
[ backport to linux-4.19.y branch, solve minor conflicts ] Signed-off-by: Qu Wenruo <wqu@suse.com>
[ copy logs and deadlock analysis from Qu's patch ] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A failed call to kobject_init_and_add() must be followed by a call to
kobject_put(). Currently in the error path when adding fs_devices we
are missing this call. This could be fixed by calling
btrfs_sysfs_remove_fsid() if btrfs_sysfs_add_fsid() returns an error or
by adding a call to kobject_put() directly in btrfs_sysfs_add_fsid().
Here we choose the second option because it prevents the slightly
unusual error path handling requirements of kobject from leaking out
into btrfs functions.
Add a call to kobject_put() in the error path of kobject_add_and_init().
This causes the release method to be called if kobject_init_and_add()
fails. open_tree() is the function that calls btrfs_sysfs_add_fsid()
and the error code in this function is already written with the
assumption that the release method is called during the error path of
open_tree() (as seen by the call to btrfs_sysfs_remove_fsid() under the
fail_fsdev_sysfs label).
Cc: stable@vger.kernel.org # v4.4+ Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tobin C. Harding <tobin@kernel.org> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If a call to kobject_init_and_add() fails we must call kobject_put()
otherwise we leak memory.
Calling kobject_put() when kobject_init_and_add() fails drops the
refcount back to 0 and calls the ktype release method (which in turn
calls the percpu destroy and kfree).
Add call to kobject_put() in the error path of call to
kobject_init_and_add().
Cc: stable@vger.kernel.org # v4.4+ Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tobin C. Harding <tobin@kernel.org> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When we do a full fsync (the bit BTRFS_INODE_NEEDS_FULL_SYNC is set in the
inode) that happens to be ranged, which happens during a msync() or writes
for files opened with O_SYNC for example, we can end up with a corrupt log,
due to different file extent items representing ranges that overlap with
each other, or hit some assertion failures.
When doing a ranged fsync we only flush delalloc and wait for ordered
exents within that range. If while we are logging items from our inode
ordered extents for adjacent ranges complete, we end up in a race that can
make us insert the file extent items that overlap with others we logged
previously and the assertion failures.
For example, if tree-log.c:copy_items() receives a leaf that has the
following file extents items, all with a length of 4K and therefore there
is an implicit hole in the range 68K to 72K - 1:
It copies them to the log tree. However due to the need to detect implicit
holes, it may release the path, in order to look at the previous leaf to
detect an implicit hole, and then later it will search again in the tree
for the first file extent item key, with the goal of locking again the
leaf (which might have changed due to concurrent changes to other inodes).
However when it locks again the leaf containing the first key, the key
corresponding to the extent at offset 72K may not be there anymore since
there is an ordered extent for that range that is finishing (that is,
somewhere in the middle of btrfs_finish_ordered_io()), and it just
removed the file extent item but has not yet replaced it with a new file
extent item, so the part of copy_items() that does hole detection will
decide that there is a hole in the range starting from 68K to 76K - 1,
and therefore insert a file extent item to represent that hole, having
a key offset of 68K. After that we now have a log tree with 2 different
extent items that have overlapping ranges:
1) The file extent item copied before copy_items() released the path,
which has a key offset of 72K and a length of 4K, representing the
file range 72K to 76K - 1.
2) And a file extent item representing a hole that has a key offset of
68K and a length of 8K, representing the range 68K to 76K - 1. This
item was inserted after releasing the path, and overlaps with the
extent item inserted before.
The overlapping extent items can cause all sorts of unpredictable and
incorrect behaviour, either when replayed or if a fast (non full) fsync
happens later, which can trigger a BUG_ON() when calling
btrfs_set_item_key_safe() through __btrfs_drop_extents(), producing a
trace like the following:
A sample of a corrupt log tree leaf with overlapping extents I got from
running btrfs/072:
item 14 key (295 108 200704) itemoff 2599 itemsize 53
extent data disk bytenr 0 nr 0
extent data offset 0 nr 458752 ram 458752
item 15 key (295 108 659456) itemoff 2546 itemsize 53
extent data disk bytenr 4343541760 nr 770048
extent data offset 606208 nr 163840 ram 770048
item 16 key (295 108 663552) itemoff 2493 itemsize 53
extent data disk bytenr 4343541760 nr 770048
extent data offset 610304 nr 155648 ram 770048
item 17 key (295 108 819200) itemoff 2440 itemsize 53
extent data disk bytenr 4334788608 nr 4096
extent data offset 0 nr 4096 ram 4096
The file extent item at offset 659456 (item 15) ends at offset 823296
(659456 + 163840) while the next file extent item (item 16) starts at
offset 663552.
Another different problem that the race can trigger is a failure in the
assertions at tree-log.c:copy_items(), which expect that the first file
extent item key we found before releasing the path exists after we have
released path and that the last key we found before releasing the path
also exists after releasing the path:
$ cat -n fs/btrfs/tree-log.c
4080 if (need_find_last_extent) {
4081 /* btrfs_prev_leaf could return 1 without releasing the path */
4082 btrfs_release_path(src_path);
4083 ret = btrfs_search_slot(NULL, inode->root, &first_key,
4084 src_path, 0, 0);
4085 if (ret < 0)
4086 return ret;
4087 ASSERT(ret == 0);
(...)
4103 if (i >= btrfs_header_nritems(src_path->nodes[0])) {
4104 ret = btrfs_next_leaf(inode->root, src_path);
4105 if (ret < 0)
4106 return ret;
4107 ASSERT(ret == 0);
4108 src = src_path->nodes[0];
4109 i = 0;
4110 need_find_last_extent = true;
4111 }
(...)
The second assertion implicitly expects that the last key before the path
release still exists, because the surrounding while loop only stops after
we have found that key. When this assertion fails it produces a stack like
this:
So fix this race between a full ranged fsync and writeback of adjacent
ranges by flushing all delalloc and waiting for all ordered extents to
complete before logging the inode. This is the simplest way to solve the
problem because currently the full fsync path does not deal with ranges
at all (it assumes a full range from 0 to LLONG_MAX) and it always needs
to look at adjacent ranges for hole detection. For use cases of ranged
fsyncs this can make a few fsyncs slower but on the other hand it can
make some following fsyncs to other ranges do less work or no need to do
anything at all. A full fsync is rare anyway and happens only once after
loading/creating an inode and once after less common operations such as a
shrinking truncate.
This is an issue that exists for a long time, and was often triggered by
generic/127, because it does mmap'ed writes and msync (which triggers a
ranged fsync). Adding support for the tree checker to detect overlapping
extents (next patch in the series) and trigger a WARN() when such cases
are found, and then calling btrfs_check_leaf_full() at the end of
btrfs_insert_file_extent() made the issue much easier to detect. Running
btrfs/072 with that change to the tree checker and making fsstress open
files always with O_SYNC made it much easier to trigger the issue (as
triggering it with generic/127 is very rare).
CC: stable@vger.kernel.org # 3.16+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When we are doing a full fsync (bit BTRFS_INODE_NEEDS_FULL_SYNC set) of a
file that has holes and has file extent items spanning two or more leafs,
we can end up falling to back to a full transaction commit due to a logic
bug that leads to failure to insert a duplicate file extent item that is
meant to represent a hole between the last file extent item of a leaf and
the first file extent item in the next leaf. The failure (EEXIST error)
leads to a transaction commit (as most errors when logging an inode do).
For example, we have the two following leafs:
Leaf N:
-----------------------------------------------
| ..., ..., ..., (257, FILE_EXTENT_ITEM, 64K) |
-----------------------------------------------
The file extent item at the end of leaf N has a length of 4Kb,
representing the file range from 64K to 68K - 1.
Leaf N + 1:
-----------------------------------------------
| (257, FILE_EXTENT_ITEM, 72K), ..., ..., ... |
-----------------------------------------------
The file extent item at the first slot of leaf N + 1 has a length of
4Kb too, representing the file range from 72K to 76K - 1.
During the full fsync path, when we are at tree-log.c:copy_items() with
leaf N as a parameter, after processing the last file extent item, that
represents the extent at offset 64K, we take a look at the first file
extent item at the next leaf (leaf N + 1), and notice there's a 4K hole
between the two extents, and therefore we insert a file extent item
representing that hole, starting at file offset 68K and ending at offset
72K - 1. However we don't update the value of *last_extent, which is used
to represent the end offset (plus 1, non-inclusive end) of the last file
extent item inserted in the log, so it stays with a value of 68K and not
with a value of 72K.
Then, when copy_items() is called for leaf N + 1, because the value of
*last_extent is smaller then the offset of the first extent item in the
leaf (68K < 72K), we look at the last file extent item in the previous
leaf (leaf N) and see it there's a 4K gap between it and our first file
extent item (again, 68K < 72K), so we decide to insert a file extent item
representing the hole, starting at file offset 68K and ending at offset
72K - 1, this insertion will fail with -EEXIST being returned from
btrfs_insert_file_extent() because we already inserted a file extent item
representing a hole for this offset (68K) in the previous call to
copy_items(), when processing leaf N.
The -EEXIST error gets propagated to the fsync callback, btrfs_sync_file(),
which falls back to a full transaction commit.
Fix this by adjusting *last_extent after inserting a hole when we had to
look at the next leaf.
Fixes: 4ee3fad34a9c ("Btrfs: fix fsync after hole punching when using no-holes feature") Cc: stable@vger.kernel.org # 4.14+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently when we fail to COW a path at btrfs_update_root() we end up
always aborting the transaction. However all the current callers of
btrfs_update_root() are able to deal with errors returned from it, many do
end up aborting the transaction themselves (directly or not, such as the
transaction commit path), other BUG_ON() or just gracefully cancel whatever
they were doing.
When syncing the fsync log, we call btrfs_update_root() through
tree-log.c:update_log_root(), and if it returns an -ENOSPC error, the log
sync code does not abort the transaction, instead it gracefully handles
the error and returns -EAGAIN to the fsync handler, so that it falls back
to a transaction commit. Any other error different from -ENOSPC, makes the
log sync code abort the transaction.
So remove the transaction abort from btrfs_update_log() when we fail to
COW a path to update the root item, so that if an -ENOSPC failure happens
we avoid aborting the current transaction and have a chance of the fsync
succeeding after falling back to a transaction commit.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203413 Fixes: 79787eaab46121 ("btrfs: replace many BUG_ONs with proper error handling") Cc: stable@vger.kernel.org # 4.4+ Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 4d207133e9c3 changed the types of the statistic values in struct
gfs2_lkstats from s64 to u64. Because of that, what should be a signed
value in gfs2_update_stats turned into an unsigned value. When shifted
right, we end up with a large positive value instead of a small negative
value, which results in an incorrect variance estimate.
Fixes: 4d207133e9c3 ("gfs2: Make statistics unsigned, suitable for use with do_div()") Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Cc: stable@vger.kernel.org # v4.4+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
DMA allocations that can't sleep may return non-remapped addresses, but
we do not properly handle them in the mmap and get_sgtable methods.
Resolve non-vmalloc addresses using virt_to_page to handle this corner
case.
Cc: <stable@vger.kernel.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Reviewed-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Jeff discovered that performance improves from ~375K iops to ~519K iops
on a simple psync-write fio workload when moving the location of 'struct
page' from the default PMEM location to DRAM. This result is surprising
because the expectation is that 'struct page' for dax is only needed for
third party references to dax mappings. For example, a dax-mapped buffer
passed to another system call for direct-I/O requires 'struct page' for
sending the request down the driver stack and pinning the page. There is
no usage of 'struct page' for first party access to a file via
read(2)/write(2) and friends.
However, this "no page needed" expectation is violated by
CONFIG_HARDENED_USERCOPY and the check_copy_size() performed in
copy_from_iter_full_nocache() and copy_to_iter_mcsafe(). The
check_heap_object() helper routine assumes the buffer is backed by a
slab allocator (DRAM) page and applies some checks. Those checks are
invalid, dax pages do not originate from the slab, and redundant,
dax_iomap_actor() has already validated that the I/O is within bounds.
Specifically that routine validates that the logical file offset is
within bounds of the file, then it does a sector-to-pfn translation
which validates that the physical mapping is within bounds of the block
device.
Bypass additional hardened usercopy overhead and call the 'no check'
versions of the copy_{to,from}_iter operations directly.
Fixes: 0aed55af8834 ("x86, uaccess: introduce copy_from_iter_flushcache...") Cc: <stable@vger.kernel.org> Cc: Jeff Moyer <jmoyer@redhat.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Matthew Wilcox <willy@infradead.org> Reported-and-tested-by: Jeff Smits <jeff.smits@intel.com> Acked-by: Kees Cook <keescook@chromium.org> Acked-by: Jan Kara <jack@suse.cz> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Current logic does not allow VCPU to be loaded onto CPU with
APIC ID 255. This should be allowed since the host physical APIC ID
field in the AVIC Physical APIC table entry is an 8-bit value,
and APIC ID 255 is valid in system with x2APIC enabled.
Instead, do not allow VCPU load if the host APIC ID cannot be
represented by an 8-bit value.
Also, use the more appropriate AVIC_PHYSICAL_ID_ENTRY_HOST_PHYSICAL_ID_MASK
instead of AVIC_MAX_PHYSICAL_ID_COUNT.
The iproc host eMMC/SD controller hold time does not meet the
specification in the HS50 mode. This problem can be mitigated
by disabling the HISPD bit; thus forcing the controller output
data to be driven on the falling clock edges rather than the
rising clock edges.
Stable tag (v4.12+) chosen to assist stable kernel maintainers so that
the change does not produce merge conflicts backporting to older kernel
versions. In reality, the timing bug existed since the driver was first
introduced but there is no need for this driver to be supported in kernel
versions that old.
The iproc host eMMC/SD controller hold time does not meet the
specification in the HS50 mode. This problem can be mitigated
by disabling the HISPD bit; thus forcing the controller output
data to be driven on the falling clock edges rather than the
rising clock edges.
This change applies only to the Cygnus platform.
Stable tag (v4.12+) chosen to assist stable kernel maintainers so that
the change does not produce merge conflicts backporting to older kernel
versions. In reality, the timing bug existed since the driver was first
introduced but there is no need for this driver to be supported in kernel
versions that old.
The kernel self-tests picked up an issue with CTR mode:
alg: skcipher: p8_aes_ctr encryption test failed (wrong result) on test vector 3, cfg="uneven misaligned splits, may sleep"
In the aesp8-ppc code from OpenSSL, there are two paths that
increment IVs: the bulk (8 at a time) path, and the individual
path which is used when there are fewer than 8 AES blocks to
process.
In the bulk path, the IV is incremented with vadduqm: "Vector
Add Unsigned Quadword Modulo", which does 128-bit addition.
In the individual path, however, the IV is incremented with
vadduwm: "Vector Add Unsigned Word Modulo", which instead
does 4 32-bit additions. Thus the IV would instead become FFFFFFFFFFFFFFFFFFFFFFFF00000000, throwing off the result.
Use vadduqm.
This was probably a typo originally, what with q and w being
adjacent. It is a pretty narrow edge case: I am really
impressed by the quality of the kernel self-tests!
Fixes: 5c380d623ed3 ("crypto: vmx - Add support for VMS instructions by ASM") Cc: stable@vger.kernel.org Signed-off-by: Daniel Axtens <dja@axtens.net> Acked-by: Nayna Jain <nayna@linux.ibm.com> Tested-by: Nayna Jain <nayna@linux.ibm.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This patch introduced regressions for devices that come online in
read-only state and subsequently switch to read-write.
Given how the partition code is currently implemented it is not
possible to persist the read-only flag across a device revalidate
call. This may need to get addressed in the future since it is common
for user applications to proactively call BLKRRPART.
Reverting this commit will re-introduce a regression where a
device-initiated revalidate event will cause the admin state to be
forgotten. A separate patch will address this issue.
Fixes: 20bd1d026aac ("scsi: sd: Keep disk read-only when re-reading partition") Cc: <stable@vger.kernel.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This barrier only applies to the read-modify-write operations; in
particular, it does not apply to the atomic_set() primitive.
Replace the barrier with an smp_mb().
Fixes: dac56212e8127 ("bio: skip atomic inc/dec of ->bi_cnt for most use cases") Cc: stable@vger.kernel.org Reported-by: "Paul E. McKenney" <paulmck@linux.ibm.com> Reported-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Andrea Parri <andrea.parri@amarulasolutions.com> Reviewed-by: Ming Lei <ming.lei@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Ming Lei <ming.lei@redhat.com> Cc: linux-block@vger.kernel.org Cc: "Paul E. McKenney" <paulmck@linux.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 11988499e62b ("KVM: x86: Skip EFER vs. guest CPUID checks for
host-initiated writes", 2019-04-02) introduced a "return false" in a
function returning int, and anyway set_efer has a "nonzero on error"
conventon so it should be returning 1.
Reported-by: Pavel Machek <pavel@denx.de> Fixes: 11988499e62b ("KVM: x86: Skip EFER vs. guest CPUID checks for host-initiated writes") Cc: Sean Christopherson <sean.j.christopherson@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For a single device mount using a zoned block device, the zone
information for the device is stored in the sbi->devs single entry
array and sbi->s_ndevs is set to 1. This differs from a single device
mount using a regular block device which does not allocate sbi->devs
and sets sbi->s_ndevs to 0.
However, sbi->s_devs == 0 condition is used throughout the code to
differentiate a single device mount from a multi-device mount where
sbi->s_ndevs is always larger than 1. This results in problems with
single zoned block device volumes as these are treated as multi-device
mounts but do not have the start_blk and end_blk information set. One
of the problem observed is skipping of zone discard issuing resulting in
write commands being issued to full zones or unaligned to a zone write
pointer.
Fix this problem by simply treating the cases sbi->s_ndevs == 0 (single
regular block device mount) and sbi->s_ndevs == 1 (single zoned block
device mount) in the same manner. This is done by introducing the
helper function f2fs_is_multi_device() and using this helper in place
of direct tests of sbi->s_ndevs value, improving code readability.
Fixes: 7bb3a371d199 ("f2fs: Fix zoned block device support") Cc: <stable@vger.kernel.org> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
It is possible that unlinked inode enters ext4_setattr() (e.g. if
somebody calls ftruncate(2) on unlinked but still open file). In such
case we should not delete the inode from the orphan list if truncate
fails. Note that this is mostly a theoretical concern as filesystem is
corrupted if we reach this path anyway but let's be consistent in our
orphan handling.
Reviewed-by: Ira Weiny <ira.weiny@intel.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
User Mode Linux does not have access to the ip or sp fields of the pt_regs,
and accessing them causes UML to fail to build. Hide the int3_emulate_jmp()
and int3_emulate_call() instructions from UML, as it doesn't need them
anyway.
Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Denis Efremov [Thu, 1 Aug 2019 17:45:17 +0000 (10:45 -0700)]
floppy: fix out-of-bounds read in copy_buffer
CVE-2019-14283
This fixes a global out-of-bounds read access in the copy_buffer
function of the floppy driver.
The FDDEFPRM ioctl allows one to set the geometry of a disk. The sect
and head fields (unsigned int) of the floppy_drive structure are used to
compute the max_sector (int) in the make_raw_rw_request function. It is
possible to overflow the max_sector. Next, max_sector is passed to the
copy_buffer function and used in one of the memcpy calls.
An unprivileged user could trigger the bug if the device is accessible,
but requires a floppy disk to be inserted.
The patch adds the check for the .sect * .head multiplication for not
overflowing in the set_geometry function.
The bug was found by syzkaller.
Signed-off-by: Denis Efremov <efremov@ispras.ru> Tested-by: Willy Tarreau <w@1wt.eu> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(cherry picked from commit da99466ac243f15fbba65bd261bfc75ffa1532b6) Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Acked-by: Colin Ian King <colin.king@canonical.com> Acked-by: Tyler Hicks <tyhicks@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This fixes a divide by zero error in the setup_format_params function of
the floppy driver.
Two consecutive ioctls can trigger the bug: The first one should set the
drive geometry with such .sect and .rate values for the F_SECT_PER_TRACK
to become zero. Next, the floppy format operation should be called.
A floppy disk is not required to be inserted. An unprivileged user
could trigger the bug if the device is accessible.
The patch checks F_SECT_PER_TRACK for a non-zero value in the
set_geometry function. The proper check should involve a reasonable
upper limit for the .sect and .rate fields, but it could change the
UAPI.
The patch also checks F_SECT_PER_TRACK in the setup_format_params, and
cancels the formatting operation in case of zero.
(cherry picked from commit f3554aeb991214cbfafd17d55e2bfddb50282e32) Signed-off-by: Sultan Alsawaf <sultan.alsawaf@canonical.com> Acked-by: Colin Ian King <colin.king@canonical.com> Acked-by: Po-Hsu Lin <po-hsu.lin@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 993f70b886c0062fb5ec7c3c556d074bb3380b9d, which is 14a1336e6fff47dd1028b484d6c802105c58e2ee upstream, has been wrongly
backported to bionic/linux changing a different function, causing
the build to failure when CONFIG_NVM is disabled. The function which it
fixed isn't implemented yet on 4.15, so it can be safely reverted.
Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Acked-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Andrea Righi <andrea.righi@canonical.com> Acked-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For iptable module to load a bpf program from a pinned location, it
only retrieve a loaded program and cannot change the program content so
requiring a write permission for it might not be necessary.
Also when adding or removing an unrelated iptable rule, it might need to
flush and reload the xt_bpf related rules as well and triggers the inode
permission check. It might be better to remove the write premission
check for the inode so we won't need to grant write access to all the
processes that flush and restore iptables rules.
MI_00 ZTE Mobile Broadband Diagnostics Port
MI_01 ZTE Mobile Broadband AT Port
MI_02 ZTE Mobile Broadband Modem
MI_03 ZTE Mobile Broadband NDIS Port (qmi_wwan)
MI_04 ZTE Mobile Broadband ADB Port
Reported-by: Lars Melin <larsm17@gmail.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Starting from commit 9c225f2655e3 ("vfs: atomic f_pos accesses as per
POSIX") files opened even via nonseekable_open gate read and write via lock
and do not allow them to be run simultaneously. This can create read vs
write deadlock if a filesystem is trying to implement a socket-like file
which is intended to be simultaneously used for both read and write from
filesystem client. See commit 10dce8af3422 ("fs: stream_open - opener for
stream-like files so that read and write can run simultaneously without
deadlock") for details and e.g. commit 581d21a2d02a ("xenbus: fix deadlock
on writes to /proc/xen/xenbus") for a similar deadlock example on
/proc/xen/xenbus.
To avoid such deadlock it was tempting to adjust fuse_finish_open to use
stream_open instead of nonseekable_open on just FOPEN_NONSEEKABLE flags,
but grepping through Debian codesearch shows users of FOPEN_NONSEEKABLE,
and in particular GVFS which actually uses offset in its read and write
handlers
so if we would do such a change it will break a real user.
Add another flag (FOPEN_STREAM) for filesystem servers to indicate that the
opened handler is having stream-like semantics; does not use file position
and thus the kernel is free to issue simultaneous read and write request on
opened file handle.
This patch together with stream_open() should be added to stable kernels
starting from v3.14+. This will allow to patch OSSPD and other FUSE
filesystems that provide stream-like files to return FOPEN_STREAM |
FOPEN_NONSEEKABLE in open handler and this way avoid the deadlock on all
kernel versions. This should work because fuse_finish_open ignores unknown
open flags returned from a filesystem and so passing FOPEN_STREAM to a
kernel that is not aware of this flag cannot hurt. In turn the kernel that
is not aware of FOPEN_STREAM will be < v3.14 where just FOPEN_NONSEEKABLE
is sufficient to implement streams without read vs write deadlock.
Reestablish the PCIe link very early in the resume process in case it
went down to prevent PCI accesses from hanging the bus. Such accesses
can happen early in the PCI resume process, as early as the
SUSPEND_RESUME_NOIRQ step, thus the link must be reestablished in the
driver resume_noirq() callback.
Fixes: e015f88c368d ("PCI: rcar: Add support for R-Car H3 to pcie-rcar") Signed-off-by: Kazufumi Ikeda <kaz-ikeda@xc.jp.nec.com> Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
[lorenzo.pieralisi@arm.com: reformatted commit log] Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Cc: stable@vger.kernel.org Cc: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Phil Edworthy <phil.edworthy@renesas.com> Cc: Simon Horman <horms+renesas@verge.net.au> Cc: Wolfram Sang <wsa@the-dreams.de> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
PLLs with tuner_en bit, such as APLL1, need to disable
tuner_en before apply new frequency settings, or the new frequency
settings (pcw) will not be applied.
The tuner_en bit will be disabled during changing PLL rate
and be restored after new settings applied.
Currently if many flush requests are submitted to an md device is quick
succession, they are serialized and can take a long to process them all.
We don't really need to call flush all those times - a single flush call
can satisfy all requests submitted before it started.
So keep track of when the current flush started and when it finished,
allow any pending flush that was requested before the flush started
to complete without waiting any more.
Test results from Xiao:
Test is done on a raid10 device which is created by 4 SSDs. The tool is
dbench.
Prevent userspace from changing the the /proc/PID/attr values if the
task's credentials are currently overriden. This not only makes sense
conceptually, it also prevents some really bizarre error cases caused
when trying to commit credentials to a task with overridden
credentials.
Cc: <stable@vger.kernel.org> Reported-by: "chengjian (D)" <cj.chengjian@huawei.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Acked-by: John Johansen <john.johansen@canonical.com> Acked-by: James Morris <james.morris@microsoft.com> Acked-by: Casey Schaufler <casey@schaufler-ca.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
__GFP_HIGHMEM is disabled if dax is enabled on brd, however
dax support for brd has been removed since commit (7a862fbbdec6
"brd: remove dax support"), so restore __GFP_HIGHMEM in
brd_insert_page().
Also remove the no longer applicable comments about DAX and highmem.
Currently, nla_put_iflink() doesn't put the IFLA_LINK attribute when
iflink == ifindex.
In some cases, a device can be created in a different netns with the
same ifindex as its parent. That device will not dump its IFLA_LINK
attribute, which can confuse some userspace software that expects it.
For example, if the last ifindex created in init_net and foo are both
8, these commands will trigger the issue:
ip link add parent type dummy # ifindex 9
ip link add link parent netns foo type macvlan # ifindex 9 in ns foo
So, in case a device puts the IFLA_LINK_NETNSID attribute in a dump,
always put the IFLA_LINK attribute as well.
Thanks to Dan Winship for analyzing the original OpenShift bug down to
the missing netlink attribute.
v2: change Fixes tag, it's been here forever, as Nicolas Dichtel said
add Nicolas' ack
v3: change Fixes tag
fix subject typo, spotted by Edward Cree
Analyzed-by: Dan Winship <danw@redhat.com> Fixes: d8a5ec672768 ("[NET]: netlink support for moving devices between network namespaces.") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A fallthrough in switch/case was introduced in f627caf55b8e ("fbdev:
sm712fb: fix crashes and garbled display during DPMS modesetting"),
due to my copy-paste error, which would cause the memory clock frequency
for SM720 to be programmed to SM712.
Since it only reprograms the clock to a different frequency, it's only
a benign issue without visible side-effect, so it also evaded Sudip
Mukherjee's code review and regression tests. scripts/checkpatch.pl
also failed to discover the issue, possibly due to nested switch
statements.
This issue was found by Stephen Rothwell by building linux-next with
-Wimplicit-fallthrough.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Fixes: f627caf55b8e ("fbdev: sm712fb: fix crashes and garbled display during DPMS modesetting") Signed-off-by: Yifeng Li <tomli@tomli.me> Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Cc: "Gustavo A. R. Silva" <gustavo@embeddedor.com> Cc: Kees Cook <keescook@chromium.org> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
One of the biggest issues we face right now with picking LRU map over
regular hash table is that a map walk out of user space, for example,
to just dump the existing entries or to remove certain ones, will
completely mess up LRU eviction heuristics and wrong entries such
as just created ones will get evicted instead. The reason for this
is that we mark an entry as "in use" via bpf_lru_node_set_ref() from
system call lookup side as well. Thus upon walk, all entries are
being marked, so information of actual least recently used ones
are "lost".
In case of Cilium where it can be used (besides others) as a BPF
based connection tracker, this current behavior causes disruption
upon control plane changes that need to walk the map from user space
to evict certain entries. Discussion result from bpfconf [0] was that
we should simply just remove marking from system call side as no
good use case could be found where it's actually needed there.
Therefore this patch removes marking for regular LRU and per-CPU
flavor. If there ever should be a need in future, the behavior could
be selected via map creation flag, but due to mentioned reason we
avoid this here.
[0] http://vger.kernel.org/bpfconf.html
Fixes: 29ba732acbee ("bpf: Add BPF_MAP_TYPE_LRU_HASH") Fixes: 8f8449384ec3 ("bpf: Add BPF_MAP_TYPE_LRU_PERCPU_HASH") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Add a callback map_lookup_elem_sys_only() that map implementations
could use over map_lookup_elem() from system call side in case the
map implementation needs to handle the latter differently than from
the BPF data path. If map_lookup_elem_sys_only() is set, this will
be preferred pick for map lookups out of user space. This hook is
used in a follow-up fix for LRU map, but once development window
opens, we can convert other map types from map_lookup_elem() (here,
the one called upon BPF_MAP_LOOKUP_ELEM cmd is meant) over to use
the callback to simplify and clean up the latter.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In commit 376991db4b64 ("driver core: Postpone DMA tear-down until after
devres release"), we changed the ordering of tearing down the device DMA
ops and releasing all the device's resources; this was because the DMA ops
should be maintained until we release the device's managed DMA memories.
However, we have seen another crash on an arm64 system when a
device driver probe fails:
hisi_sas_v3_hw 0000:74:02.0: Adding to iommu group 2
scsi host1: hisi_sas_v3_hw
BUG: Bad page state in process swapper/0 pfn:313f5
page:ffff7e0000c4fd40 count:1 mapcount:0
mapping:0000000000000000 index:0x0
flags: 0xfffe00000001000(reserved)
raw: 0fffe00000001000ffff7e0000c4fd48ffff7e0000c4fd48 0000000000000000
raw: 0000000000000000000000000000000000000001ffffffff 0000000000000000
page dumped because: PAGE_FLAGS_CHECK_AT_FREE flag(s) set
bad because of flags: 0x1000(reserved)
Modules linked in:
CPU: 49 PID: 1 Comm: swapper/0 Not tainted 5.1.0-rc1-43081-g22d97fd-dirty #1433
Hardware name: Huawei D06/D06, BIOS Hisilicon D06 UEFI
RC0 - V1.12.01 01/29/2019
Call trace:
dump_backtrace+0x0/0x118
show_stack+0x14/0x1c
dump_stack+0xa4/0xc8
bad_page+0xe4/0x13c
free_pages_check_bad+0x4c/0xc0
__free_pages_ok+0x30c/0x340
__free_pages+0x30/0x44
__dma_direct_free_pages+0x30/0x38
dma_direct_free+0x24/0x38
dma_free_attrs+0x9c/0xd8
dmam_release+0x20/0x28
release_nodes+0x17c/0x220
devres_release_all+0x34/0x54
really_probe+0xc4/0x2c8
driver_probe_device+0x58/0xfc
device_driver_attach+0x68/0x70
__driver_attach+0x94/0xdc
bus_for_each_dev+0x5c/0xb4
driver_attach+0x20/0x28
bus_add_driver+0x14c/0x200
driver_register+0x6c/0x124
__pci_register_driver+0x48/0x50
sas_v3_pci_driver_init+0x20/0x28
do_one_initcall+0x40/0x25c
kernel_init_freeable+0x2b8/0x3c0
kernel_init+0x10/0x100
ret_from_fork+0x10/0x18
Disabling lock debugging due to kernel taint
BUG: Bad page state in process swapper/0 pfn:313f6
page:ffff7e0000c4fd80 count:1 mapcount:0
mapping:0000000000000000 index:0x0
[ 89.322983] flags: 0xfffe00000001000(reserved)
raw: 0fffe00000001000ffff7e0000c4fd88ffff7e0000c4fd88 0000000000000000
raw: 0000000000000000000000000000000000000001ffffffff 0000000000000000
The crash occurs for the same reason.
In this case, on the really_probe() failure path, we are still clearing
the DMA ops prior to releasing the device's managed memories.
This patch fixes this issue by reordering the DMA ops teardown and the
call to devres_release_all() on the failure path.
Reported-by: Xiang Chen <chenxiang66@hisilicon.com> Tested-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Reviewed-by: Robin Murphy <robin.murphy@arm.com>
[jpg: backport to 4.19.x and earlier] Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The problem is that any 'uptodate' vs 'disks' check is not precise
in this path. Put a "WARN_ON(!test_bit(R5_UPTODATE, &dev->flags)" on the
device that might try to kick off writes and then skip the action.
Better to prevent the raid driver from taking unexpected action *and* keep
the system alive vs killing the machine with BUG_ON.
Note: fixed warning reported by kbuild test robot <lkp@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Nigel Croxon <ncroxon@redhat.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
While cross building perf to the ARC architecture on a fedora 30 host,
we were failing with:
CC /tmp/build/perf/bench/numa.o
bench/numa.c: In function ‘worker_thread’:
bench/numa.c:1261:12: error: ‘RUSAGE_THREAD’ undeclared (first use in this function); did you mean ‘SIGEV_THREAD’?
getrusage(RUSAGE_THREAD, &rusage);
^~~~~~~~~~~~~
SIGEV_THREAD
bench/numa.c:1261:12: note: each undeclared identifier is reported only once for each function it appears in
[perfbuilder@60d5802468f6 perf]$ /arc_gnu_2019.03-rc1_prebuilt_uclibc_le_archs_linux_install/bin/arc-linux-gcc --version | head -1
arc-linux-gcc (ARCv2 ISA Linux uClibc toolchain 2019.03-rc1) 8.3.1 20190225
[perfbuilder@60d5802468f6 perf]$
Trying to reproduce a report by Vineet, I noticed that, with just
cross-built zlib and numactl libraries, I ended up with the above
failure.
So, since RUSAGE_THREAD is available as a define, check for that and
numactl libraries, I ended up with the above failure.
So, since RUSAGE_THREAD is available as a define in the system headers,
check if it is defined in the 'perf bench numa' sources and define it if
not.
Now it builds and I have to figure out if the problem reported by Vineet
only takes place if we have libelf or some other library available.
Cc: Arnd Bergmann <arnd@arndb.de> Cc: Jiri Olsa <jolsa@kernel.org> Cc: linux-snps-arc@lists.infradead.org Cc: Namhyung Kim <namhyung@kernel.org> Cc: Vineet Gupta <Vineet.Gupta1@synopsys.com> Link: https://lkml.kernel.org/n/tip-2wb4r1gir9xrevbpq7qp0amk@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
To choose whether to pick the GID from the old (16bit) or new (32bit)
field, we should check if the old gid field is set to 0xffff. Mainline
checks the old *UID* field instead - cut'n'paste from the corresponding
code in ufs_get_inode_uid().
Fixes: 252e211e90ce Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Enablement of AMD's Secure Memory Encryption feature is determined very
early after start_kernel() is entered. Part of this procedure involves
scanning the command line for the parameter 'mem_encrypt'.
To determine intended state, the function sme_enable() uses library
functions cmdline_find_option() and strncmp(). Their use occurs early
enough such that it cannot be assumed that any instrumentation subsystem
is initialized.
For example, making calls to a KASAN-instrumented function before KASAN
is set up will result in the use of uninitialized memory and a boot
failure.
When AMD's SME support is enabled, conditionally disable instrumentation
of these dependent functions in lib/string.c and arch/x86/lib/cmdline.c.
[ bp: Get rid of intermediary nostackp var and cleanup whitespace. ]
Fixes: aca20d546214 ("x86/mm: Add support to make use of Secure Memory Encryption") Reported-by: Li RongQing <lirongqing@baidu.com> Signed-off-by: Gary R Hook <gary.hook@amd.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Boris Brezillon <bbrezillon@kernel.org> Cc: Coly Li <colyli@suse.de> Cc: "dave.hansen@linux.intel.com" <dave.hansen@linux.intel.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Kees Cook <keescook@chromium.org> Cc: Kent Overstreet <kent.overstreet@gmail.com> Cc: "luto@kernel.org" <luto@kernel.org> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: "mingo@redhat.com" <mingo@redhat.com> Cc: "peterz@infradead.org" <peterz@infradead.org> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/155657657552.7116.18363762932464011367.stgit@sosrh3.amd.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We don't check for the validity of the lengths in the packet received
from the firmware. If the MPDU length received in the rx descriptor
is too short to contain the header length and the crypt length
together, we may end up trying to copy a negative number of bytes
(headlen - hdrlen < 0) which will underflow and cause us to try to
copy a huge amount of data. This causes oopses such as this one:
Fix a similar endless event loop as was done in commit 8dcf32175b4e ("i2c: prevent endless uevent loop with
CONFIG_I2C_DEBUG_CORE"):
The culprit is the dev_dbg printk in the i2c uevent handler. If
this is activated (for instance by CONFIG_I2C_DEBUG_CORE) it results
in an endless loop with systemd-journald.
This happens if user-space scans the system log and reads the uevent
file to get information about a newly created device, which seems
fair use to me. Unfortunately reading the "uevent" file uses the
same function that runs for creating the uevent for a new device,
generating the next syslog entry
Both CONFIG_I2C_DEBUG_CORE and CONFIG_POWER_SUPPLY_DEBUG were reported
in https://bugs.freedesktop.org/show_bug.cgi?id=76886 but only former
seems to have been fixed. Drop debug prints as it was done in I2C
subsystem to resolve the issue.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Chris Healy <cphealy@gmail.com> Cc: linux-pm@vger.kernel.org Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A failed KVM_ARM_VCPU_INIT should not set the vcpu target,
as the vcpu target is used by kvm_vcpu_initialized() to
determine if other vcpu ioctls may proceed. We need to set
the target before calling kvm_reset_vcpu(), but if that call
fails, we should then unset it and clear the feature bitmap
while we're at it.
Signed-off-by: Andrew Jones <drjones@redhat.com>
[maz: Simplified patch, completed commit message] Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The txq of vif is added to active_txqs list for ATF TXQ scheduling
in the function ieee80211_queue_skb(), but it was not properly removed
before freeing the txq object. It was causing use after free of the txq
objects from the active_txqs list, result was kernel panic
due to invalid memory access.
Fix kernel invalid memory access by properly removing txq object
from active_txqs list before free the object.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org> Acked-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
symlink body shouldn't be freed without an RCU delay. Switch apparmorfs
to ->destroy_inode() and use of call_rcu(); free both the inode and symlink
body in the callback.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
symlink body shouldn't be freed without an RCU delay. Switch securityfs
to ->destroy_inode() and use of call_rcu(); free both the inode and symlink
body in the callback.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We currently don't reload pointers pointing into skb header
after doing pskb_may_pull() in _decode_session4(). So in case
pskb_may_pull() changed the pointers, we read from random
memory. Fix this by putting all the needed infos on the
stack, so that we don't need to access the header pointers
after doing pskb_may_pull().
esp_output_udp_encap can produce a length that doesn't fit in the 16
bits of a UDP header's length field. In that case, we'll send a
fragmented packet whose length is larger than IP_MAX_MTU (resulting in
"Oversized IP packet" warnings on receive) and with a bogus UDP
length.
To prevent this, add a length check to esp_output_udp_encap and return
-EMSGSIZE on failure.
If tunnel registration failed during module initialization, the module
would fail to deregister the IPPROTO_COMP protocol and would attempt to
deregister the tunnel.
The tunnel was not deregistered during module-exit.
Fixes: dd9ee3444014e ("vti4: Fix a ipip packet processing bug in 'IPCOMP' virtual tunnel") Signed-off-by: Jeremy Sowden <jeremy@azazel.net> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When unloading xfrm6_tunnel module, xfrm6_tunnel_fini directly
frees the xfrm6_tunnel_spi_kmem. Maybe someone has gotten the
xfrm6_tunnel_spi, so need to wait it.
Fixes: 91cc3bb0b04ff("xfrm6_tunnel: RCU conversion") Signed-off-by: Su Yanjun <suyj.fnst@cn.fujitsu.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
xfrm_add_policy
-->verify_newpolicy_info //check the index provided by user with XFRM_POLICY_MAX
//In my case, the index is 0x6E6BB6, so it pass the check.
-->xfrm_policy_construct //copy the user's policy and set xfrm_policy_timer
-->xfrm_policy_insert
--> __xfrm_policy_link //use the orgin dir, in my case is 2
--> xfrm_gen_index //generate policy index, there is 0x6E6BB6
then xfrm_policy_timer be fired
xfrm_policy_timer
--> xfrm_policy_id2dir //get dir from (policy index & 7), in my case is 6
--> xfrm_policy_delete
--> __xfrm_policy_unlink //access policy_count[dir], trigger out of range access
Add xfrm_policy_id2dir check in verify_newpolicy_info, make sure the computed dir is
valid, to fix the issue.
Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: e682adf021be ("xfrm: Try to honor policy index if it's supplied by user") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When the target line contains an invalid device, delay_ctr() will call
delay_dtr() with NULL workqueue. Attempting to destroy the NULL
workqueue causes a crash.
The function blkdev_report_zones() returns success even if no zone
information is reported (empty report). Empty zone reports can only
happen if the report start sector passed exceeds the device capacity.
The conditions for this to happen are either a bug in the caller code,
or, a change in the device that forced the low level driver to change
the device capacity to a value that is lower than the report start
sector. This situation includes a failed disk revalidation resulting in
the disk capacity being changed to 0.
If this change happens while dm-zoned is in its initialization phase
executing dmz_init_zones(), this function may enter an infinite loop
and hang the system. To avoid this, add a check to disallow empty zone
reports and bail out early. Also fix the function dmz_update_zone() to
make sure that the report for the requested zone was correctly obtained.
Fixes: 3b1a94c88b79 ("dm zoned: drive-managed zoned block device target") Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Reviewed-by: Shaun Tancheff <shaun@tancheff.com> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Due to an erratum in some Pericom PCIe-to-PCI bridges in reverse mode
(conventional PCI on primary side, PCIe on downstream side), the Retrain
Link bit needs to be cleared manually to allow the link training to
complete successfully.
If it is not cleared manually, the link training is continuously restarted
and no devices below the PCI-to-PCIe bridge can be accessed. That means
drivers for devices below the bridge will be loaded but won't work and may
even crash because the driver is only reading 0xffff.
See the Pericom Errata Sheet PI7C9X111SLB_errata_rev1.2_102711.pdf for
details. Devices known as affected so far are: PI7C9X110, PI7C9X111SL,
PI7C9X130.
Add a new flag, clear_retrain_link, in struct pci_dev. Quirks for affected
devices set this bit.
Note that pcie_retrain_link() lives in aspm.c because that's currently the
only place we use it, but this erratum is not specific to ASPM, and we may
retrain links for other reasons in the future.
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
[bhelgaas: apply regardless of CONFIG_PCIEASPM] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> CC: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When using PCI passthrough with this device, the host machine locks up
completely when starting the VM, requiring a hard reboot. Add a quirk to
avoid bus resets on this device.
Fixes: c3e59ee4e766 ("PCI: Mark Atheros AR93xx to avoid bus reset") Link: https://lore.kernel.org/linux-pci/20190107213248.3034-1-james.prestwood@linux.intel.com Signed-off-by: James Prestwood <james.prestwood@linux.intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: stable@vger.kernel.org # v3.14+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
ATS is broken on the Radeon R7 GPU (at least for Stoney Ridge based laptop)
and causes IOMMU stalls and system failure. Disable ATS on these devices
to make them usable again with IOMMU enabled.
Thanks to Joerg Roedel <jroedel@suse.de> for help.
[bhelgaas: In the email thread mentioned below, Alex suspects the real
problem is in sbios or iommu, so it may affect only certain systems, and it
may affect other devices in those systems as well. However, per Joerg we
lack the ability to debug further, so this quirk is the best we can do for
now.]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194521 Link: https://lore.kernel.org/lkml/20190408103725.30426-1-nickel@altlinux.org Fixes: 9b44b0b09dec ("PCI: Mark AMD Stoney GPU ATS as broken") Signed-off-by: Nikolai Kostrigin <nickel@altlinux.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Joerg Roedel <jroedel@suse.de> CC: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On a Thinkpad s30 (Pentium III / i440MX, Lynx3DM), blanking the display
or starting the X server will crash and freeze the system, or garble the
display.
Experiments showed this problem can mostly be solved by adjusting the
order of register writes. Also, sm712fb failed to consider the difference
of clock frequency when unblanking the display, and programs the clock for
SM712 to SM720.
Fix them by adjusting the order of register writes, and adding an
additional check for SM720 for programming the clock frequency.
Loongson MIPS netbooks use 1024x600 LCD panels, which is the original
target platform of this driver, but nearly all old x86 laptops have
1024x768. Lighting 768 panels using 600's timings would partially
garble the display. Since it's not possible to distinguish them reliably,
we change the default to 768, but keep 600 as-is on MIPS.
Further, earlier laptops, such as IBM Thinkpad 240X, has a 800x600 LCD
panel, this driver would probably garbled those display. As we don't
have one for testing, the original behavior of the driver is kept as-is,
but the problem has been documented is the comments.
In order to support the 1024x600 panel on Yeeloong Loongson MIPS
laptop, the original 1024x768-16 table was modified to 1024x600-16,
without leaving the original. It causes problem on x86 laptop as
the 1024x768-16 support was still claimed but not working.
On a Thinkpad s30 (Pentium III / i440MX, Lynx3DM), running fbtest or X
will crash the machine instantly, because the VRAM/framebuffer is not
mapped correctly.
On SM712, the framebuffer starts at the beginning of address space, but
SM720's framebuffer starts at the 1 MiB offset from the beginning. However,
sm712fb fails to take this into account, as a result, writing to the
framebuffer will destroy all the registers and kill the system immediately.
Another problem is the driver assumes 8 MiB of VRAM for SM720, but some
SM720 system, such as this IBM Thinkpad, only has 4 MiB of VRAM.
Fix this problem by removing the hardcoded VRAM size, adding a function to
query the amount of VRAM from register MCR76 on SM720, and adding proper
framebuffer offset.
Please note that the memory map may have additional problems on Big-Endian
system, which is not available for testing by myself. But I highly suspect
that the original code is also broken on Big-Endian machines for SM720, so
at least we are not making the problem worse. More, the driver also assumed
SM710/SM712 has 4 MiB of VRAM, but it has a 2 MiB version as well, and used
in earlier laptops, such as IBM Thinkpad 240X, the driver would probably
crash on them. I've never seen one of those machines and cannot fix it, but
I have documented these problems in the comments.
When the machine is booted in VGA mode, loading sm712fb would cause
a glitch of random pixels shown on the screen. To prevent it from
happening, we first clear the entire framebuffer, and we also need
to stop calling smtcfb_setmode() during initialization, the fbdev
layer will call it for us later when it's ready.
On a Thinkpad s30 (Pentium III / i440MX, Lynx3DM), rebooting with
sm712fb framebuffer driver would cause a white screen of death on
the next POST, presumably the proper timings for the LCD panel was
not reprogrammed properly by the BIOS.
Experiments showed a few CRTC Scratch Registers, including CRT3D,
CRT3E and CRT3F may be used internally by BIOS as some flags. CRT3B is
a hardware testing register, we shouldn't mess with it. CRT3C has
blanking signal and line compare control, which is not needed for this
driver.
Stop writing to CR3B-CR3F (a.k.a CRT3B-CRT3F) registers. Even if these
registers don't have side-effect on other systems, writing to them is
also highly questionable.
On a Thinkpad s30 (Pentium III / i440MX, Lynx3DM), the amount of Video
RAM is not detected correctly by the xf86-video-siliconmotion driver.
This is because sm712fb overwrites the GPR71 Scratch Pad Register, which
is set by BIOS on x86 and used to indicate amount of VRAM.
Other Scratch Pad Registers, including GPR70/74/75, don't have the same
side-effect, but overwriting to them is still questionable, as they are
not related to modesetting.
Stop writing to SR70/71/74/75 (a.k.a GPR70/71/74/75).
On a Thinkpad s30 (Pentium III / i440MX, Lynx3DM), rebooting with
sm712fb framebuffer driver would cause the role of brightness up/down
button to swap.
Experiments showed the FPR30 register caused this behavior. Moreover,
even if this register don't have side-effect on other systems, over-
writing it is also highly questionable, since it was originally
configurated by the motherboard manufacturer by hardwiring pull-down
resistors to indicate the type of LCD panel. We should not mess with
it.
The sample timestamp is updated to ensure that the timestamp represents
the time of the sample and not a branch that the decoder is still
walking towards. The sample timestamp is updated when the decoder
returns, but the decoder does not return for non-taken branches. Update
the sample timestamp then also.
Note that commit 3f04d98e972b5 ("perf intel-pt: Improve sample
timestamp") was also a stable fix and appears, for example, in v4.4
stable tree as commit a4ebb58fd124 ("perf intel-pt: Improve sample
timestamp").
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: stable@vger.kernel.org # v4.4+ Fixes: 3f04d98e972b ("perf intel-pt: Improve sample timestamp") Link: http://lkml.kernel.org/r/20190510124143.27054-4-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The decoder uses its current timestamp in samples. Usually that is a
timestamp that has already passed, but in some cases it is a timestamp
for a branch that the decoder is walking towards, and consequently
hasn't reached.
The intel_pt_sample_time() function decides which is which, but was not
handling TNT packets exactly correctly.
In the case of TNT, the timestamp applies to the first branch, so the
decoder must first walk to that branch.
That means intel_pt_sample_time() should return true for TNT, and this
patch makes that change. However, if the first branch is a non-taken
branch (i.e. a 'N'), then intel_pt_sample_time() needs to return false
for subsequent taken branches in the same TNT packet.
To handle that, introduce a new state INTEL_PT_STATE_TNT_CONT to
distinguish the cases.
Note that commit 3f04d98e972b5 ("perf intel-pt: Improve sample
timestamp") was also a stable fix and appears, for example, in v4.4
stable tree as commit a4ebb58fd124 ("perf intel-pt: Improve sample
timestamp").
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: stable@vger.kernel.org # v4.4+ Fixes: 3f04d98e972b5 ("perf intel-pt: Improve sample timestamp") Link: http://lkml.kernel.org/r/20190510124143.27054-3-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The timestamp used to determine if an instruction sample is made, is an
estimate based on the number of instructions since the last known
timestamp. A consequence is that it might go backwards, which results in
extra samples. Change it so that a sample is only made when the
timestamp goes forwards.
Note this does not affect a sampling period of 0 or sampling periods
specified as a count of instructions.
Example:
Before:
$ perf script --itrace=i10us
ls 13812 [003] 2167315.222583: 3270 instructions:u: 7fac71e2e494 __GI___tunables_init+0xf4 (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222667: 30902 instructions:u: 7fac71e2da0f _dl_cache_libcmp+0x2f (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222667: 10 instructions:u: 7fac71e2d9ff _dl_cache_libcmp+0x1f (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222667: 8 instructions:u: 7fac71e2d9ea _dl_cache_libcmp+0xa (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222667: 14 instructions:u: 7fac71e2d9ea _dl_cache_libcmp+0xa (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222667: 6 instructions:u: 7fac71e2d9ff _dl_cache_libcmp+0x1f (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222667: 14 instructions:u: 7fac71e2d9ff _dl_cache_libcmp+0x1f (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222667: 4 instructions:u: 7fac71e2dab2 _dl_cache_libcmp+0xd2 (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222728: 16423 instructions:u: 7fac71e2477a _dl_map_object_deps+0x1ba (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222734: 12731 instructions:u: 7fac71e27938 _dl_name_match_p+0x68 (/lib/x86_64-linux-gnu/ld-2.28.so)
...
projects / mirror_ubuntu-bionic-kernel.git / log