If IRQ handlers are threaded (either because CONFIG_PREEMPT_RT_BASE is
enabled or "threadirqs" was passed on the command line) and if system
load is sufficiently high that wakeup latency of IRQ threads degrades,
SPI DMA transactions on the BCM2835 occasionally break like this:
ks8851 spi0.0: SPI transfer timed out
bcm2835-dma 3f007000.dma: DMA transfer could not be terminated
ks8851 spi0.0 eth2: ks8851_rdfifo: spi_sync() failed
The root cause is an assumption made by the DMA driver which is
documented in a code comment in bcm2835_dma_terminate_all():
/*
* Stop DMA activity: we assume the callback will not be called
* after bcm_dma_abort() returns (even if it does, it will see
* c->desc is NULL and exit.)
*/
That assumption falls apart if the IRQ handler bcm2835_dma_callback() is
threaded: A client may terminate a descriptor and issue a new one
before the IRQ handler had a chance to run. In fact the IRQ handler may
miss an *arbitrary* number of descriptors. The result is the following
race condition:
1. A descriptor finishes, its interrupt is deferred to the IRQ thread.
2. A client calls dma_terminate_async() which sets channel->desc = NULL.
3. The client issues a new descriptor. Because channel->desc is NULL,
bcm2835_dma_issue_pending() immediately starts the descriptor.
4. Finally the IRQ thread runs and writes BCM2835_DMA_INT to the CS
register to acknowledge the interrupt. This clears the ACTIVE flag,
so the newly issued descriptor is paused in the middle of the
transaction. Because channel->desc is not NULL, the IRQ thread
finalizes the descriptor and tries to start the next one.
I see two possible solutions: The first is to call synchronize_irq()
in bcm2835_dma_issue_pending() to wait until the IRQ thread has
finished before issuing a new descriptor. The downside of this approach
is unnecessary latency if clients desire rapidly terminating and
re-issuing descriptors and don't have any use for an IRQ callback.
(The SPI TX DMA channel is a case in point.)
A better alternative is to make the IRQ thread recognize that it has
missed descriptors and avoid finalizing the newly issued descriptor.
So first of all, set the ACTIVE flag when acknowledging the interrupt.
This keeps a newly issued descriptor running.
If the descriptor was finished, the channel remains idle despite the
ACTIVE flag being set. However the ACTIVE flag can then no longer be
used to check whether the channel is idle, so instead check whether
the register containing the current control block address is zero
and finalize the current descriptor only if so.
That way, there is no impact on latency and throughput if the client
doesn't care for the interrupt: Only minimal additional overhead is
introduced for non-cyclic descriptors as one further MMIO read is
necessary per interrupt to check for idleness of the channel. Cyclic
descriptors are sped up slightly by removing one MMIO write per
interrupt.
Fixes: 96286b576690 ("dmaengine: Add support for BCM2835") Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: stable@vger.kernel.org # v3.14+ Cc: Frank Pavlic <f.pavlic@kunbus.de> Cc: Martin Sperl <kernel@martin.sperl.org> Cc: Florian Meier <florian.meier@koalo.de> Cc: Clive Messer <clive.m.messer@gmail.com> Cc: Matthias Reichl <hias@horus.com> Tested-by: Stefan Wahren <stefan.wahren@i2se.com> Acked-by: Florian Kauer <florian.kauer@koalo.de> Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In the current code, the codec registration may happen both at the
codec bind time and the end of the controller probe time. In a rare
occasion, they race with each other, leading to Oops due to the still
uninitialized card device.
This patch introduces a simple flag to prevent the codec registration
at the codec bind time as long as the controller probe is going on.
The controller probe invokes snd_card_register() that does the whole
registration task, and we don't need to register each piece
beforehand.
It is normal user behaviour to start, stop, then start a stream
again without closing it. Currently this works for compressed
playback streams but not capture ones.
The states on a compressed capture stream go directly from OPEN to
PREPARED, unlike a playback stream which moves to SETUP and waits
for a write of data before moving to PREPARED. Currently however,
when a stop is sent the state is set to SETUP for both types of
streams. This leaves a capture stream in the situation where a new
start can't be sent as that requires the state to be PREPARED and
a new set_params can't be sent as that requires the state to be
OPEN. The only option being to close the stream, and then reopen.
Correct this issues by allowing snd_compr_drain_notify to set the
state depending on the stream direction, as we already do in
set_params.
Fixes: 49bb6402f1aa ("ALSA: compress_core: Add support for capture streams") Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The unbalance of master's promiscuity or allmulti will happen after ifdown
and ifup a slave interface which is in a bridge.
When we ifdown a slave interface , both the 'dsa_slave_close' and
'dsa_slave_change_rx_flags' will clear the master's flags. The flags
of master will be decrease twice.
In the other hand, if we ifup the slave interface again, since the
slave's flags were cleared the 'dsa_slave_open' won't set the master's
flag, only 'dsa_slave_change_rx_flags' that triggered by 'br_add_if'
will set the master's flags. The flags of master is increase once.
Only propagating flag changes when a slave interface is up makes
sure this does not happen. The 'vlan_dev_change_rx_flags' had the
same problem and was fixed, and changes here follows that fix.
Fixes: 91da11f870f0 ("net: Distributed Switch Architecture protocol support") Signed-off-by: Rundong Ge <rdong.ge@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When an ethernet frame is padded to meet the minimum ethernet frame
size, the padding octets are not covered by the hardware checksum.
Fortunately the padding octets are usually zero's, which don't affect
checksum. However, we have a switch which pads non-zero octets, this
causes kernel hardware checksum fault repeatedly.
Prior to:
commit '88078d98d1bb ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE ...")'
skb checksum was forced to be CHECKSUM_NONE when padding is detected.
After it, we need to keep skb->csum updated, like what we do for RXFCS.
However, fixing up CHECKSUM_COMPLETE requires to verify and parse IP
headers, it is not worthy the effort as the packets are so small that
CHECKSUM_COMPLETE can't save anything.
Fixes: 88078d98d1bb ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"), Cc: Eric Dumazet <edumazet@google.com> Cc: Tariq Toukan <tariqt@mellanox.com> Cc: Nikola Ciprich <nikola.ciprich@linuxbox.cz> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Broadcom STB chips support a deep sleep mode where all register
contents are lost. Because we were stashing the MagicPacket password
into some of these registers a suspend into that deep sleep then a
resumption would not lead to being able to wake-up from MagicPacket with
password again.
Fix this by keeping a software copy of the password and program it
during suspend.
Fixes: 83e82f4c706b ("net: systemport: add Wake-on-LAN support") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The "p" buffer is 0x4000 bytes long. B3_RI_WTO_R1 is 0x190. The value
of "regs->len" is in the 1-0x4000 range. The bug here is that
"regs->len - B3_RI_WTO_R1" can be a negative value which would lead to
memory corruption and an abrupt crash.
Fixes: c3f8be961808 ("[PATCH] skge: expand ethtool debug register dump") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When either "goto wait_interrupted;" or "goto wait_error;"
paths are taken, socket lock has already been released.
This patch fixes following syzbot splat :
WARNING: bad unlock balance detected!
5.0.0-rc4+ #59 Not tainted
-------------------------------------
syz-executor223/8256 is trying to release lock (sk_lock-AF_RXRPC) at:
[<ffffffff86651353>] rxrpc_recvmsg+0x6d3/0x3099 net/rxrpc/recvmsg.c:598
but there are no more locks to release!
other info that might help us debug this:
1 lock held by syz-executor223/8256:
#0: 00000000fa9ed0f4 (slock-AF_RXRPC){+...}, at: spin_lock_bh include/linux/spinlock.h:334 [inline]
#0: 00000000fa9ed0f4 (slock-AF_RXRPC){+...}, at: release_sock+0x20/0x1c0 net/core/sock.c:2798
Fixes: 248f219cb8bc ("rxrpc: Rewrite the data and ack handling code") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: David Howells <dhowells@redhat.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
During sendmsg() a cloned skb is saved via dp83640_txtstamp() in
->tx_queue. After the NIC sends this packet, the PHY will reply with a
timestamp for that TX packet. If the cable is pulled at the right time I
don't see that packet. It might gets flushed as part of queue shutdown
on NIC's side.
Once the link is up again then after the next sendmsg() we enqueue
another skb in dp83640_txtstamp() and have two on the list. Then the PHY
will send a reply and decode_txts() attaches it to the first skb on the
list.
No crash occurs since refcounting works but we are one packet behind.
linuxptp/ptp4l usually closes the socket and opens a new one (in such a
timeout case) so those "stale" replies never get there. However it does
not resume normal operation anymore.
Purge old skbs in decode_txts().
Fixes: cb646e2b02b2 ("ptp: Added a clock driver for the National Semiconductor PHYTER.") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Avoid warnings like this:
thermal_hwmon.h:29:1: warning: ‘thermal_remove_hwmon_sysfs’ defined but not used [-Wunused-function]
thermal_remove_hwmon_sysfs(struct thermal_zone_device *tz)
Fixes: 0dd88793aacd ("thermal: hwmon: move hwmon support to single file") Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Eduardo Valentin <edubezval@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A bug is present in GDB which causes early string termination when
parsing variables. This has been reported [0], but we should ensure
that we can support at least basic printing of the core kernel strings.
For current gdb version (has been tested with 7.3 and 8.1), 'lx-version'
only prints one character.
(gdb) lx-version
L(gdb)
This can be fixed by casting 'linux_banner' as (char *).
(gdb) lx-version
Linux version 4.19.0-rc1+ (changbin@acer) (gcc version 7.3.0 (Ubuntu 7.3.0-16ubuntu3)) #21 SMP Sat Sep 1 21:43:30 CST 2018
The ep->ovflist is a secondary ready-list to temporarily store events
that might occur when doing sproc without holding the ep->wq.lock. This
accounts for every time we check for ready events and also send events
back to userspace; both callbacks, particularly the latter because of
copy_to_user, can account for a non-trivial time.
As such, the unlikely() check to see if the pointer is being used, seems
both misleading and sub-optimal. In fact, we go to an awful lot of
trouble to sync both lists, and populating the ovflist is far from an
uncommon scenario.
For example, profiling a concurrent epoll_wait(2) benchmark, with
CONFIG_PROFILE_ANNOTATED_BRANCHES shows that for a two threads a 33%
incorrect rate was seen; and when incrementally increasing the number of
epoll instances (which is used, for example for multiple queuing load
balancing models), up to a 90% incorrect rate was seen.
Similarly, by deleting the prediction, 3% throughput boost was seen
across incremental threads.
Link: http://lkml.kernel.org/r/20181108051006.18751-4-dave@stgolabs.net Signed-off-by: Davidlohr Bueso <dbueso@suse.de> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Jason Baron <jbaron@akamai.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Based on commit 401c636a0eeb ("kernel/hung_task.c: show all hung tasks
before panic"), we could get the call stack of hung task.
However, if the console loglevel is not high, we still can not see the
useful panic information in practice, and in most cases users don't set
console loglevel to high level.
This patch is to force console verbose before system panic, so that the
real useful information can be seen in the console, instead of being
like the following, which doesn't have hung task information.
INFO: task init:1 blocked for more than 120 seconds.
Tainted: G U W 4.19.0-quilt-2e5dc0ac-g51b6c21d76cc #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
Kernel panic - not syncing: hung_task: blocked tasks
CPU: 2 PID: 479 Comm: khungtaskd Tainted: G U W 4.19.0-quilt-2e5dc0ac-g51b6c21d76cc #1
Call Trace:
dump_stack+0x4f/0x65
panic+0xde/0x231
watchdog+0x290/0x410
kthread+0x12c/0x150
ret_from_fork+0x35/0x40
reboot: panic mode set: p,w
Kernel Offset: 0x34000000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffffbfffffff)
Link: http://lkml.kernel.org/r/27240C0AC20F114CBF8149A2696CBE4A6015B675@SHSMSX101.ccr.corp.intel.com Signed-off-by: Chuansheng Liu <chuansheng.liu@intel.com> Reviewed-by: Petr Mladek <pmladek@suse.com> Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There are three processing functions dealing with digital parameters,
__do_proc_dointvec/__do_proc_douintvec/__do_proc_doulongvec_minmax.
This patch deals with __do_proc_doulongvec_minmax, just as
__do_proc_dointvec does, adding a check for parameters 'left'. In
__do_proc_douintvec, its code implementation explicitly does not support
multiple inputs.
static int __do_proc_douintvec(...){
...
/*
* Arrays are not supported, keep this simple. *Do not* add
* support for them.
*/
if (vleft != 1) {
*lenp = 0;
return -EINVAL;
}
...
}
So, just __do_proc_doulongvec_minmax has the problem. And most use of
proc_doulongvec_minmax/proc_doulongvec_ms_jiffies_minmax just have one
parameter.
Link: http://lkml.kernel.org/r/1544081775-15720-1-git-send-email-cheng.lin130@zte.com.cn Signed-off-by: Cheng Lin <cheng.lin130@zte.com.cn> Acked-by: Luis Chamberlain <mcgrof@kernel.org> Reviewed-by: Kees Cook <keescook@chromium.org> Cc: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
check_hung_uninterruptible_tasks() is currently calling rcu_lock_break()
for every 1024 threads. But check_hung_task() is very slow if printk()
was called, and is very fast otherwise.
If many threads within some 1024 threads called printk(), the RCU grace
period might be extended enough to trigger RCU stall warnings.
Therefore, calling rcu_lock_break() for every some fixed jiffies will be
safer.
Link: http://lkml.kernel.org/r/1544800658-11423-1-git-send-email-penguin-kernel@I-love.SAKURA.ne.jp Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Acked-by: Paul E. McKenney <paulmck@linux.ibm.com> Cc: Petr Mladek <pmladek@suse.com> Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com> Cc: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
First correct the edge case to return the last element if we're
outside the range, rather than at the last element, so that
interpolation is not omitted for points between the two last entries in
the table.
Then correct the formula to perform linear interpolation based the two
points surrounding the read ADC value. The indices for temp are kept as
"hi" and "lo" to pair with the adc indices, but there's no requirement
that the temperature is provided in descendent order. mult_frac() is
used to prevent issues with overflowing the int.
If you have a CPU that fails to round up and then run 'btc' you'll end
up crashing in kdb becaue we dereferenced NULL. Let's add a check.
It's wise to also set the task to NULL when leaving the debugger so
that if we fail to round up on a later entry into the debugger we
won't backtrace a stale task.
Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
By defaul of-based thermal driver do not enable hwmon.
This patch does this explicitly, so that the temperature can be read
through the common hwmon sysfs.
When the block device is opened with FMODE_EXCL, ref_count is set to -1.
This value doesn't get reset when the device is closed which means the
device cannot be opened again. Fix this by checking for refcount <= 0
in the release method.
Reported-and-tested-by: Stan Johnson <userm57@yahoo.com> Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Signed-off-by: Scott Wood <oss@buserror.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In probe_gdrom(), the buffer pointed by 'gd.cd_info' is allocated through
kzalloc() and is used to hold the information of the gdrom device. To
register and unregister the device, the pointer 'gd.cd_info' is passed to
the functions register_cdrom() and unregister_cdrom(), respectively.
However, this buffer is not freed after it is used, which can cause a
memory leak bug.
This patch simply frees the buffer 'gd.cd_info' in exit_gdrom() to fix the
above issue.
Signed-off-by: Wenwen Wang <wang6495@umn.edu> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In drivers/isdn/hisax/hfc_pci.c, the functions hfcpci_interrupt() and
HFCPCI_l1hw() may be concurrently executed.
HFCPCI_l1hw()
line 1173: if (!cs->tx_skb)
hfcpci_interrupt()
line 942: spin_lock_irqsave();
line 1066: dev_kfree_skb_irq(cs->tx_skb);
Thus, a possible concurrency use-after-free bug may occur
in HFCPCI_l1hw().
To fix these bugs, the calls to spin_lock_irqsave() and
spin_unlock_irqrestore() are added in HFCPCI_l1hw(), to protect the
access to cs->tx_skb.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Included file path was hard-wired in the ocfs2 makefile, which might
causes some confusion when compiling ocfs2 as an external module.
Say if we compile ocfs2 module as following.
cp -r /kernel/tree/fs/ocfs2 /other/dir/ocfs2
cd /other/dir/ocfs2
make -C /path/to/kernel_source M=`pwd` modules
Acutally, the compiler wil try to find included file in
/kernel/tree/fs/ocfs2, rather than the directory /other/dir/ocfs2.
To fix this little bug, we introduce the var $(src) provided by kbuild.
$(src) means the absolute path of the running kbuild file.
Link: http://lkml.kernel.org/r/20181108085546.15149-1-lchen@suse.com Signed-off-by: Larry Chen <lchen@suse.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <jiangqi903@gmail.com> Cc: Changwei Ge <ge.changwei@h3c.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For sync io read in ocfs2_read_blocks_sync(), first clear bh uptodate flag
and submit the io, second wait io done, last check whether bh uptodate, if
not return io error.
If two sync io for the same bh were issued, it could be the first io done
and set uptodate flag, but just before check that flag, the second io came
in and cleared uptodate, then ocfs2_read_blocks_sync() for the first io
will return IO error.
Indeed it's not necessary to clear uptodate flag, as the io end handler
end_buffer_read_sync() will set or clear it based on io succeed or failed.
The following message was found from a nfs server but the underlying
storage returned no error.
[4106438.567376] (nfsd,7146,3):ocfs2_get_suballoc_slot_bit:2780 ERROR: read block 1238823695 failed -5
[4106438.567569] (nfsd,7146,3):ocfs2_get_suballoc_slot_bit:2812 ERROR: status = -5
[4106438.567611] (nfsd,7146,3):ocfs2_test_inode_bit:2894 ERROR: get alloc slot and bit failed -5
[4106438.567643] (nfsd,7146,3):ocfs2_test_inode_bit:2932 ERROR: status = -5
[4106438.567675] (nfsd,7146,3):ocfs2_get_dentry:94 ERROR: test inode bit failed -5
Same issue in non sync read ocfs2_read_blocks(), fixed it as well.
Link: http://lkml.kernel.org/r/20181121020023.3034-4-junxiao.bi@oracle.com Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Reviewed-by: Changwei Ge <ge.changwei@h3c.com> Reviewed-by: Yiwen Jiang <jiangyiwen@huawei.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Joseph Qi <jiangqi903@gmail.com> Cc: Jun Piao <piaojun@huawei.com> Cc: Mark Fasheh <mfasheh@versity.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
leads to interested results where not only the leading "." gets stripped
from the displayed paths, but also anywhere in the string, displaying
something like:
This fixes the case where all mount options specified are consumed by an
LSM and all that's left is an empty string. In this case cgroupfs should
accept the string and not fail.
How to reproduce (with SELinux enabled):
# umount /sys/fs/cgroup/unified
# mount -o context=system_u:object_r:cgroup_t:s0 -t cgroup2 cgroup2 /sys/fs/cgroup/unified
mount: /sys/fs/cgroup/unified: wrong fs type, bad option, bad superblock on cgroup2, missing codepage or helper program, or other error.
# dmesg | tail -n 1
[ 31.575952] cgroup: cgroup2: unknown option ""
Fixes: 67e9c74b8a87 ("cgroup: replace __DEVEL__sane_behavior with cgroup2 fs type")
[NOTE: should apply on top of commit 5136f6365ce3 ("cgroup: implement "nsdelegate" mount option"), older versions need manual rebase] Suggested-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When there is a failure in f2fs_fill_super() after/during
the recovery of fsync'd nodes, it frees the current sbi and
retries again. This time the mount is successful, but the files
that got recovered before retry, still holds the extent tree,
whose extent nodes list is corrupted since sbi and sbi->extent_list
is freed up. The list_del corruption issue is observed when the
file system is getting unmounted and when those recoverd files extent
node is being freed up in the below context.
list_del corruption. prev->next should be fffffff1e1ef5480, but was (null)
<...>
kernel BUG at kernel/msm-4.14/lib/list_debug.c:53!
lr : __list_del_entry_valid+0x94/0xb4
pc : __list_del_entry_valid+0x94/0xb4
<...>
Call trace:
__list_del_entry_valid+0x94/0xb4
__release_extent_node+0xb0/0x114
__free_extent_tree+0x58/0x7c
f2fs_shrink_extent_tree+0xdc/0x3b0
f2fs_leave_shrinker+0x28/0x7c
f2fs_put_super+0xfc/0x1e0
generic_shutdown_super+0x70/0xf4
kill_block_super+0x2c/0x5c
kill_f2fs_super+0x44/0x50
deactivate_locked_super+0x60/0x8c
deactivate_super+0x68/0x74
cleanup_mnt+0x40/0x78
__cleanup_mnt+0x1c/0x28
task_work_run+0x48/0xd0
do_notify_resume+0x678/0xe98
work_pending+0x8/0x14
Fix this by not creating extents for those recovered files if shrinker is
not registered yet. Once mount is successful and shrinker is registered,
those files can have extents again.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
niu_pci_eeprom_read() may fail, so we should check its return value
before using the read data.
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Acked-by: Shannon Nelson <shannon.lee.nelson@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Changing protection is a very high cost operation in UML
because in addition to an extra syscall it also interrupts
mmap merge sequences generated by the tlb.
While the condition is not particularly common it is worth
avoiding.
Signed-off-by: Anton Ivanov <anton.ivanov@cambridgegreys.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There is an issue where when multiple threads open/close the same directory
ntwrk_buf_start might end up being NULL, causing the call to smbCalcSize
later to oops with a NULL deref.
The real bug is why this happens and why this can become NULL for an
open cfile, which should not be allowed.
This patch tries to avoid a oops until the time when we fix the underlying
issue.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Testing has shown, that when using mainline U-Boot on MT7688 based
boards, the system may hang or crash while mounting the root-fs. The
main issue here is that mainline U-Boot configures EBase to a value
near the end of system memory. And with CONFIG_CPU_MIPSR2_IRQ_VI
disabled, trap_init() will not allocate a new area to place the
exception handler. The original value will be used and the handler
will be copied to this location, which might already be used by some
userspace application.
The MT7688 supports VI - its config3 register is 0x00002420, so VInt
(Bit 5) is set. But without setting CONFIG_CPU_MIPSR2_IRQ_VI this
bit will not be evaluated to result in "cpu_has_vi" being set. This
patch now selects CONFIG_CPU_MIPSR2_IRQ_VI on MT7620/8 which results
trap_init() to allocate some memory for the exception handler.
Please note that this issue was not seen with the Mediatek U-Boot
version, as it does not touch EBase (stays at default of 0x8000.0000).
This is strictly also not correct as the kernel (_text) resides
here.
Signed-off-by: Stefan Roese <sr@denx.de>
[paul.burton@mips.com: s/beeing/being/] Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: John Crispin <blogic@openwrt.org> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Clang warns when one enumerated type is implicitly converted to another:
drivers/crypto/ux500/hash/hash_core.c:169:4: warning: implicit
conversion from enumeration type 'enum dma_data_direction' to different
enumeration type 'enum dma_transfer_direction' [-Wenum-conversion]
direction, DMA_CTRL_ACK | DMA_PREP_INTERRUPT);
^~~~~~~~~
1 warning generated.
dmaengine_prep_slave_sg expects an enum from dma_transfer_direction.
We know that the only direction supported by this function is
DMA_TO_DEVICE because of the check at the top of this function so we can
just use the equivalent value from dma_transfer_direction.
DMA_TO_DEVICE = DMA_MEM_TO_DEV = 1
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Clang warns when one enumerated type is implicitly converted to another:
drivers/crypto/ux500/cryp/cryp_core.c:559:5: warning: implicit
conversion from enumeration type 'enum dma_data_direction' to different
enumeration type 'enum dma_transfer_direction' [-Wenum-conversion]
direction, DMA_CTRL_ACK);
^~~~~~~~~
drivers/crypto/ux500/cryp/cryp_core.c:583:5: warning: implicit
conversion from enumeration type 'enum dma_data_direction' to different
enumeration type 'enum dma_transfer_direction' [-Wenum-conversion]
direction,
^~~~~~~~~
2 warnings generated.
dmaengine_prep_slave_sg expects an enum from dma_transfer_direction.
Because we know the value of the dma_data_direction enum from the
switch statement, we can just use the proper value from
dma_transfer_direction so there is no more conversion.
Currently seq_buf_puts() will happily create a non null-terminated
string for you in the buffer. This is particularly dangerous if the
buffer is on the stack.
In lm80_probe(), if lm80_read_value() fails, it returns a negative
error number which is stored to data->fan[f_min] and will be further
used. We should avoid using the data if the read fails.
The fix checks if lm80_read_value() fails, and if so, returns with the
error number.
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This patch removes the check from nfs_compare_mount_options to see if a
`sec' option was passed for the current mount before comparing auth
flavors and instead just always compares auth flavors.
Consider the following scenario:
You have a server with the address 192.168.1.1 and two exports /export/a
and /export/b. The first export supports `sys' and `krb5' security, the
second just `sys'.
Assume you start with no mounts from the server.
The following results in EIOs being returned as the kernel nfs client
incorrectly thinks it can share the underlying `struct nfs_server's:
Since the offset is added directly to the hva from the
gfn_to_hva_cache, a negative offset could result in an out of bounds
write. The existing BUG_ON only checks for addresses beyond the end of
the gfn_to_hva_cache, not for addresses before the start of the
gfn_to_hva_cache.
Note that all current call sites have non-negative offsets.
For fadump to work successfully there should not be any holes in reserved
memory ranges where kernel has asked firmware to move the content of old
kernel memory in event of crash. Now that fadump uses CMA for reserved
area, this memory area is now not protected from hot-remove operations
unless it is cma allocated. Hence, fadump service can fail to re-register
after the hot-remove operation, if hot-removed memory belongs to fadump
reserved region. To avoid this make sure that memory from fadump reserved
area is not hot-removable if fadump is registered.
However, if user still wants to remove that memory, he can do so by
manually stopping fadump service before hot-remove operation.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
AMD doesn't seem to implement MSR_IA32_MCG_EXT_CTL and svm code in kvm
knows nothing about it, however, this MSR is among emulated_msrs and
thus returned with KVM_GET_MSR_INDEX_LIST. The consequent KVM_GET_MSRS,
of course, fails.
Report the MSR as unsupported to not confuse userspace.
The GPIOAO pins (as well as the two exotic GPIO_BSD_EN and GPIO_TEST_N)
only belong to the pin controller in the AO domain. With the current
definition these pins cannot be referred to in .dts files as group
(which is possible on GXBB and GXL for example).
Add a separate "gpio_aobus" function to fix the mapping between the pin
controller and the GPIO pins in the AO domain. This is similar to how
the GXBB and GXL drivers implement this functionality.
Fixes: 9dab1868ec0db4 ("pinctrl: amlogic: Make driver independent from two-domain configuration") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The GPIOAO pins (as well as the two exotic GPIO_BSD_EN and GPIO_TEST_N)
only belong to the pin controller in the AO domain. With the current
definition these pins cannot be referred to in .dts files as group
(which is possible on GXBB and GXL for example).
Add a separate "gpio_aobus" function to fix the mapping between the pin
controller and the GPIO pins in the AO domain. This is similar to how
the GXBB and GXL drivers implement this functionality.
Fixes: 9dab1868ec0db4 ("pinctrl: amlogic: Make driver independent from two-domain configuration") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When unregistering fbdev using unregister_framebuffer(), any bound
console will unbind automatically. This is working fine if this is the
only framebuffer, resulting in a switch to the dummy console. However if
there is a fb0 and I unregister fb1 having a bound console, I eventually
get a crash. The fastest way for me to trigger the crash is to do a
reboot, resulting in this splat:
The problem is in the console rebinding in fbcon_fb_unbind(). It uses the
virtual console index as the new framebuffer index to bind the console(s)
to. The correct way is to use the con2fb_map lookup table to find the
framebuffer index.
In __ghes_panic() clear the block status in the APEI generic
error status block for that generic hardware error source before
calling panic() to prevent a second panic() in the crash kernel
for exactly the same fatal error.
Otherwise ghes_probe(), running in the crash kernel, would see
an unhandled error in the APEI generic error status block and
panic again, thereby precluding any crash dump.
Signed-off-by: Lenny Szubowicz <lszubowi@redhat.com> Signed-off-by: David Arcari <darcari@redhat.com> Tested-by: Tyler Baicar <baicar.tyler@gmail.com> Acked-by: Borislav Petkov <bp@suse.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
i40iw_net_event() reads unconditionally 16 bytes from
neigh->primary_key while the memory allocated for
"neighbour" struct is evaluated in neigh_alloc() as
tbl->entry_size + dev->neigh_priv_len
where "dev" is a net_device.
But the driver does not setup dev->neigh_priv_len and
we read beyond the neigh entry allocated memory,
so the patch in the next mail fixes this.
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Blitting an image with "negative" offsets is not working since there
is no clipping. It hopefully just crashes. For the bootup logo, there
is protection so that blitting does not happen as the image is drawn
further and further to the right (ROTATE_UR) or further and further
down (ROTATE_CW). There is however no protection when drawing in the
opposite directions (ROTATE_UD and ROTATE_CCW).
Add back this protection.
The regression is 20-odd years old but the mindless warning-killing
mentality displayed in commit 34bdb666f4b2 ("fbdev: fbmem: remove
positive test on unsigned values") is also to blame, methinks.
Fixes: 448d479747b8 ("fbdev: fb_do_show_logo() updates") Signed-off-by: Peter Rosin <peda@axentia.se> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Fabian Frederick <ffrederick@users.sourceforge.net> Cc: Geert Uytterhoeven <geert+renesas@glider.be>
cc: Geoff Levand <geoff@infradead.org> Cc: James Simmons <jsimmons@users.sf.net> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There are several warnings from Clang about no case statement matching
the constant 0:
In file included from drivers/block/drbd/drbd_receiver.c:48:
In file included from drivers/block/drbd/drbd_int.h:48:
In file included from ./include/linux/drbd_genl_api.h:54:
In file included from ./include/linux/genl_magic_struct.h:236:
./include/linux/drbd_genl.h:321:1: warning: no case matching constant
switch condition '0'
GENL_struct(DRBD_NLA_HELPER, 24, drbd_helper_info,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/genl_magic_struct.h:220:10: note: expanded from macro
'GENL_struct'
switch (0) {
^
Silence this warning by adding a 'case 0:' statement. Additionally,
adjust the alignment of the statements in the ct_assert_unique macro to
avoid a checkpatch warning.
This solution was originally sent by Arnd Bergmann with a default case
statement: https://lore.kernel.org/patchwork/patch/756723/
If you try to promote a Secondary while connected to a Primary
and allow-two-primaries is NOT set, we will wait for "ping-timeout"
to give this node a chance to detect a dead primary,
in case the cluster manager noticed faster than we did.
But if we then are *still* connected to a Primary,
we fail (after an additional timeout of ping-timout).
This change skips the spurious second timeout.
Most people won't notice really,
since "ping-timeout" by default is half a second.
But in some installations, ping-timeout may be 10 or 20 seconds or more,
and spuriously delaying the error return becomes annoying.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
With "on-no-data-accessible suspend-io", DRBD requires the next attach
or connect to be to the very same data generation uuid tag it lost last.
If we first lost connection to the peer,
then later lost connection to our own disk,
we would usually refuse to re-connect to the peer,
because it presents the wrong data set.
However, if the peer first connects without a disk,
and then attached its disk, we accepted that same wrong data set,
which would be "unexpected" by any user of that DRBD
and cause "undefined results" (read: very likely data corruption).
The fix is to forcefully disconnect as soon as we notice that the peer
attached to the "wrong" dataset.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
MMCRA[34:36] and MMCRA[38:44] expose the thresholding counter value.
Thresholding counter can be used to count latency cycles such as
load miss to reload. But threshold counter value is not relevant
when the sampled instruction type is unknown or reserved. Patch to
fix the thresholding counter value to zero when sampled instruction
type is unknown or reserved.
Fixes: 170a315f41c6('powerpc/perf: Support to export MMCRA[TEC*] field to userspace') Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The function cw1200_bss_info_changed() and cw1200_hw_scan() can be
concurrently executed.
The two functions both access a possible shared variable "frame.skb".
This shared variable is freed by dev_kfree_skb() in cw1200_upload_beacon(),
which is called by cw1200_bss_info_changed(). The free operation is
protected by a mutex lock "priv->conf_mutex" in cw1200_bss_info_changed().
In cw1200_hw_scan(), this shared variable is accessed without the
protection of the mutex lock "priv->conf_mutex".
Thus, concurrency use-after-free bugs may occur.
To fix these bugs, the original calls to mutex_lock(&priv->conf_mutex) and
mutex_unlock(&priv->conf_mutex) are moved to the places, which can
protect the accesses to the shared variable.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
- fix race condition when a unit is deleted after an RLL,
and before we have gotten the LV_STATUS page of the unit.
- In this case we will get a standard inquiry, rather than
the desired page. This will result in a unit presented
which no longer exists.
- If we ask for LV_STATUS, insure we get LV_STATUS
Reviewed-by: Murthy Bhat <murthy.bhat@microsemi.com> Reviewed-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com> Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Dave Carroll <david.carroll@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When a LAG device or a VLAN device on top of it is enslaved to a bridge,
the driver propagates the CHANGEUPPER event to the LAG's slaves.
This causes each physical port to increase the reference count of the
internal representation of the bridge port by calling
mlxsw_sp_port_bridge_join().
However, when a port is removed from a LAG, the corresponding leave()
function is not called and the reference count is not decremented. This
leads to ugly hacks such as mlxsw_sp_bridge_port_should_destroy() that
try to understand if the bridge port should be destroyed even when its
reference count is not 0.
Instead, make sure that when a port is unlinked from a LAG it would see
the same events as if the LAG (or its uppers) were unlinked from a
bridge.
The above is achieved by walking the LAG's uppers when a port is
unlinked and calling mlxsw_sp_port_bridge_leave() for each upper that is
enslaved to a bridge.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Due to the alignment handling, it actually matters where in the code
we add the 4 bytes for the presence bitmap to the length; the first
field is the timestamp with 8 byte alignment so we need to add the
space for the extra vendor namespace presence bitmap *before* we do
any alignment for the fields.
Move the presence bitmap length accounting to the right place to fix
the alignment for the data properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
From Michael Cree:
"Bisection lead to commit b38d08f3181c ("percpu: restructure
locking") as being the cause of lockups at initial boot on
the kernel built for generic Alpha.
On a suggestion by Tejun Heo that:
So, the only thing I can think of is that it's calling
spin_unlock_irq() while irq handling isn't set up yet.
Can you please try the followings?
1. Convert all spin_[un]lock_irq() to
spin_lock_irqsave/unlock_irqrestore()."
Fixes: b38d08f3181c ("percpu: restructure locking") Reported-and-tested-by: Michael Cree <mcree@orcon.net.nz> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Dennis Zhou <dennis@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Due to lack of ID pin interrupt event on AM335x devices, the musb dsps
driver uses polling to detect usb device attach for dual-role port.
But in the case if a micro-A cable adapter is attached without a USB device
attached to the cable, the musb state machine gets stuck in a_wait_vrise
state waiting for the MUSB_CONNECT interrupt which won't happen due to the
usb device is not attached. The state is stuck in a_wait_vrise even after
the micro-A cable is detached, which could cause VBUS retention if then the
dual-role port is attached to a host port.
To fix the problem, make a_wait_vrise as a transient state, then move the
state to either a_wait_bcon for host port or a_idle state for dual-role
port, if no usb device is attached to the port.
Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When we emulate an MMIO instruction, we advance the CPU state within
decode_hsr(), before emulating the instruction effects.
Having this logic in decode_hsr() is opaque, and advancing the state
before emulation is problematic. It gets in the way of applying
consistent single-step logic, and it prevents us from being able to fail
an MMIO instruction with a synchronous exception.
Clean this up by only advancing the CPU state *after* the effects of the
instruction are emulated.
Cc: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Alex Bennée <alex.bennee@linaro.org> Reviewed-by: Christoffer Dall <christoffer.dall@arm.com> Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The strncpy() function may leave the destination string buffer
unterminated, better use strlcpy() that we have a __weak fallback
implementation for systems without it.
In this case the 'target' buffer is coming from a list of build-ids that
are expected to have a len of at most (SBUILD_ID_SIZE - 1) chars, so
probably we're safe, but since we're using strncpy() here, use strlcpy()
instead to provide the intended safety checking without the using the
problematic strncpy() function.
This fixes this warning on an Alpine Linux Edge system with gcc 8.2:
util/probe-file.c: In function 'probe_cache__open.isra.5':
util/probe-file.c:427:3: error: 'strncpy' specified bound 41 equals destination size [-Werror=stringop-truncation]
strncpy(sbuildid, target, SBUILD_ID_SIZE);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Cc: Namhyung Kim <namhyung@kernel.org> Fixes: 1f3736c9c833 ("perf probe: Show all cached probes") Link: https://lkml.kernel.org/n/tip-l7n8ggc9kl38qtdlouke5yp5@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The strncpy() function may leave the destination string buffer
unterminated, better use strlcpy() that we have a __weak fallback
implementation for systems without it.
This fixes this warning on an Alpine Linux Edge system with gcc 8.2:
util/header.c: In function 'perf_event__synthesize_event_update_unit':
util/header.c:3586:2: error: 'strncpy' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
strncpy(ev->data, evsel->unit, size);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
util/header.c:3579:16: note: length computed here
size_t size = strlen(evsel->unit);
^~~~~~~~~~~~~~~~~~~
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Fixes: a6e5281780d1 ("perf tools: Add event_update event unit type") Link: https://lkml.kernel.org/n/tip-fiikh5nay70bv4zskw2aa858@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 391f93f2ec9f ("serial: core: Rework hw-assited flow control support")
has changed the way the autoCTS mode is handled.
According to that change, serial drivers which enable H/W autoCTS mode must
set UPSTAT_AUTOCTS to prevent the serial core from inadvertently disabling
TX. This patch adds proper handling of UPSTAT_AUTOCTS flag.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
[mszyprow: rephrased commit message] Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The bcm2835 mmc host tends to lock up for unknown reason so reset it on
timeout. The upper mmc block layer tries retransimitting with single
blocks which tends to work out after a long wait.
This is better than giving up and leaving the machine broken for no
obvious reason.
Fixes: 660fc733bd74 ("mmc: bcm2835: Add new driver for the sdhost controller.") Signed-off-by: Michal Suchanek <msuchanek@suse.de> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Acked-by: Eric Anholt <eric@anholt.net> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If the user issues an "mmc extcsd read", the SD controller receives
what it thinks is a SEND_IF_COND command with an unexpected data block.
The resulting operations leave the FSM stuck in READWAIT, a state which
persists until the MMC framework resets the controller, by which point
the root filesystem is likely to have been unmounted.
A less heavyweight solution is to detect the condition and nudge the
FSM by asserting the (self-clearing) FORCE_DATA_MODE bit.
Link: https://github.com/raspberrypi/linux/issues/2728 Signed-off-by: Phil Elwell <phil@raspberrypi.org> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Acked-by: Eric Anholt <eric@anholt.net> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The kvm capability KVM_CAP_SPAPR_TCE_VFIO is used to indicate the
availability of in kernel tce acceleration for vfio. However it is
currently the case that this is only available on a powernv machine,
not for a pseries machine.
Thus make this capability dependent on having the cpu feature
CPU_FTR_HVMODE.
[paulus@ozlabs.org - fixed compilation for Book E.]
eukrea-tlv320.c machine driver runs on non-DT platforms
and include <asm/mach-types.h> header file in order to be able
to use some machine_is_eukrea_xxx() macros.
Building it for ARM64 causes the following build error:
sound/soc/fsl/eukrea-tlv320.c:28:10: fatal error: asm/mach-types.h: No such file or directory
Avoid this error by not allowing to build the SND_SOC_EUKREA_TLV320
driver when ARM64 is selected.
This is needed in preparation for the i.MX8M support.
Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Fabio Estevam <festevam@gmail.com> Acked-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
WARNING: vmlinux.o(.text+0x19f90): Section mismatch in reference from the function littleton_init_lcd() to the function .init.text:pxa_set_fb_info()
The function littleton_init_lcd() references
the function __init pxa_set_fb_info().
This is often because littleton_init_lcd lacks a __init
annotation or the annotation of pxa_set_fb_info is wrong.
WARNING: vmlinux.o(.text+0xf824): Section mismatch in reference from the function zeus_register_ohci() to the function .init.text:pxa_set_ohci_info()
The function zeus_register_ohci() references
the function __init pxa_set_ohci_info().
This is often because zeus_register_ohci lacks a __init
annotation or the annotation of pxa_set_ohci_info is wrong.
WARNING: vmlinux.o(.text+0xf95c): Section mismatch in reference from the function cm_x300_init_u2d() to the function .init.text:pxa3xx_set_u2d_info()
The function cm_x300_init_u2d() references
the function __init pxa3xx_set_u2d_info().
This is often because cm_x300_init_u2d lacks a __init
annotation or the annotation of pxa3xx_set_u2d_info is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For some reason, my older GCC (< 4.8) isn't smart enough to optimize the
!__builtin_constant_p() branch in bpf_htons, I see:
error: implicit declaration of function '__builtin_bswap16'
Let's use __bpf_constant_htons as suggested by Daniel Borkmann.
I tried to use simple htons, but it produces the following:
test_progs.c:54:17: error: braced-group within expression allowed only
inside a function
.eth.h_proto = htons(ETH_P_IP),
Signed-off-by: Stanislav Fomichev <sdf@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In the ioctl_event_ctl() SWITCHTEC_IOCTL_EVENT_IDX_ALL case, we call
event_ctl() several times with the same "ctl" struct. Each call clobbers
ctl.flags, which leads to the problem that we may not actually enable or
disable all events as the user requested.
Preserve the event flag value with a temporary variable.
When inode is corrupted so that extent type is invalid, some functions
(such as udf_truncate_extents()) will just BUG. Check that extent type
is valid when loading the inode to memory.
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
It was observed that when using seqentional mode contrary to the
documentation, the SS bit (which is supposed to only be set if
automatic/sequence command completed normally), is sometimes set
together with NA (NAK in address phase) causing transfer to falsely be
considered successful.
My assumption is that this does not happen during manual mode since the
controller is stopping its work the moment it sets NA/ND bit in status
register. This is not the case in Automatic/Sequentional mode where it
is still working to send STOP condition and the actual status we get
depends on the time when the ISR is run.
This patch changes the order of checking status bits in ISR - error
conditions are checked first and only if none of them occurred, the
transfer may be considered successful. This is required to introduce
using of sequentional mode in next patch.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com> Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The value of opp_table->regulator_count is not very consistent right now
and it may end up being 0 while we do have a "opp-microvolt" property in
the OPP table. It was kept that way as we used to check if any
regulators are set with the OPP core for a device or not using value of
regulator_count.
Lets use opp_table->regulators for that purpose as the meaning of
regulator_count is going to change in the later patches.
of_find_node_by_path() acquires a reference to the node
returned by it and that reference needs to be dropped by its caller.
bl_idle_init() doesn't do that, so fix it.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Same as other i.MX6 SoCs, ensure unused MMDC channel's
handshake is bypassed, this is to make sure no request
signal will be generated when periphe_clk_sel is changed
or SRC warm reset is triggered.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The driver overrides the error codes returned by platform_get_irq() to
-EINVAL, so if it returns -EPROBE_DEFER, the driver would fail the probe
permanently instead of the deferred probing. Switch to propagating the
error code upstream, still checking/overriding IRQ0 as libata regards it
as "no IRQ" (thus polling) anyway...
Fixes: 9ec36cafe43b ("of/irq: do irq resolution in platform_get_irq") Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
After removing an entry from a queue (e.g. reading an event in
arm_smmu_evtq_thread()) it is necessary to advance the MMIO consumer
pointer to free the queue slot back to the SMMU. A memory barrier is
required here so that all reads targetting the queue entry have
completed before the consumer pointer is updated.
The implementation of queue_inc_cons() relies on a writel() to complete
the previous reads, but this is incorrect because writel() is only
guaranteed to complete prior writes. This patch replaces the call to
writel() with an mb(); writel_relaxed() sequence, which gives us the
read->write ordering which we require.
Cc: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
qcom,smmu-v2 is an arm,smmu-v2 implementation with specific
clock and power requirements.
On msm8996, multiple cores, viz. mdss, video, etc. use this
smmu. On sdm845, this smmu is used with gpu.
Add bindings for the same.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org> Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Tomasz Figa <tfiga@chromium.org> Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Reviewed-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In stream mode, when fast-forwarding TRBs, the stream number
is not cleared causing the new stream to not get assigned. So
we don't want controller to carry on transfers when short packet
is received. So disable the CSP for stream capable endpoint.
This is based on the 3.30a Programming guide, where table 3-1
device descriptor structure field definitions says for CSP bit
If this bit is 0, the controller generates an XferComplete event
and remove the stream. So if we keep CSP as 1 then switching between
streams would not happen as in stream mode, when fast-forwarding
TRBs, the stream number is not cleared causing the new stream to not get
assigned.
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The datasheet says we must stop the timer before changing the clock
divider. This can happen when the restart handler is called while the
watchdog is running.
Here "flash" is obviously the whole device and we know "rootfs"
is a bogus hack to point to a squashfs rootfs inside of the main
"upgrade partition". We know "RedBoot" is the first 0x40000 of
the flash and the "upgrade" partition follows from 0x40000 to
0x1f8000. So we have mtd0, 1, 4 and 6 covered.
Add support for the third loop filter mode
V4L2_MPEG_VIDEO_H264_LOOP_FILTER_MODE_DISABLED_AT_SLICE_BOUNDARY,
and fix V4L2_CID_MPEG_VIDEO_H264_LOOP_FILTER_ALPHA and
V4L2_CID_MPEG_VIDEO_H264_LOOP_FILTER_BETA controls.
The filter offset controls are signed values in the -6 to 6 range and
are stored into the slice header fields slice_alpha_c0_offset_div2 and
slice_beta_offset_div2. The actual filter offsets FilterOffsetA/B are
double their value, in range of -12 to 12.
Rename variables to more closely match the nomenclature in the H.264
specification.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For micro-mips, srlv inside POOL32A encoding space should use 0x50
sub-opcode, NOT 0x90.
Some early version ISA doc describes the encoding as 0x90 for both srlv and
srav, this looks to me was a typo. I checked Binutils libopcode
implementation which is using 0x50 for srlv and 0x90 for srav.
v1->v2:
- Keep mm_srlv32_op sorted by value.
Fixes: f31318fdf324 ("MIPS: uasm: Add srlv uasm instruction") Cc: Markos Chandras <markos.chandras@imgtec.com> Cc: Paul Burton <paul.burton@mips.com> Cc: linux-mips@vger.kernel.org Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Song Liu <songliubraving@fb.com> Signed-off-by: Jiong Wang <jiong.wang@netronome.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
It was noticed that unbinding and rebinding the KSZ8851 ethernet
resulted in the driver reporting "failed to read device ID" at probe.
Probing the reset line with a 'scope while repeatedly attempting to
bind the driver in a shell loop revealed that the KSZ8851 RSTN pin is
constantly held at zero, meaning the device is held in reset, and
does not respond on the SPI bus.
Experimentation with the startup delay on the regulator set to 50ms
shows that the reset is positively released after 20ms.
Schematics for this board are not available, and the traces are buried
in the inner layers of the board which makes tracing where the RSTN pin
extremely difficult. We can only guess that the RSTN pin is wired to a
reset generator chip driven off the ethernet supply, which fits the
observed behaviour.
Include this delay in the regulator startup delay - effectively
treating the reset as a "supply stable" indicator.
This can not be modelled as a delay in the KSZ8851 driver since the
reset generation is board specific - if the RSTN pin had been wired to
a GPIO, reset could be released earlier via the already provided support
in the KSZ8851 driver.
This also got confirmed by Peter Ujfalusi <peter.ujfalusi@ti.com> based
on Blaze schematics that should be very close to SDP4430:
TPS22902YFPR is used as the regulator switch (gpio48 controlled):
Convert arm boot_lock to raw The VOUT is routed to TPS3808G01DBV.
(SCH Note: Threshold set at 90%. Vsense: 0.405V).
According to the TPS3808 data sheet the RESET delay time when Ct is
open (this is the case in the schema): MIN/TYP/MAX: 12/20/28 ms.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated with notes from schematics from Peter] Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The parameter is still there but it's ignored. We need to check its
value before deciding to go into passthrough mode for AMD IOMMU v2
capable device.
We occasionally use this parameter to force v2 capable device into
translation mode to debug memory corruption that we suspect is
caused by DMA writes.
To address the following comment from Joerg Roedel on the first
version, v2 capability of device is completely ignored.
> This breaks the iommu_v2 use-case, as it needs a direct mapping for the
> devices that support it.
And from Documentation/admin-guide/kernel-parameters.txt:
This option does not override iommu=pt
devm_kstrdup() may return NULL if internal allocation failed.
Thus using label, name is unsafe without checking. Therefor
in the unlikely case of allocation failure, sx150x_probe() simply
returns -ENOMEM.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Fixes: 9e80f9064e73 ("pinctrl: Add SX150X GPIO Extender Pinctrl Driver") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The missed break statement in the outer switch makes the code fall through
always and thus always same value will be printed.
Besides that, compiler warns about missed fall through marker:
drivers/usb/dwc3/./trace.h: In function ‘trace_raw_output_dwc3_log_trb’:
drivers/usb/dwc3/./trace.h:246:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
switch (pcm) {
^~~~~~
Add the missing break statement to work correctly without compilation
warnings.
Fixes: fa8d965d736b ("usb: dwc3: trace: pretty print high-bandwidth transfers too") Cc: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently, When a reserved operation is completed, its entry in the send
queue will not be unreserved, which leads to the miscalculation of
qp->s_avail and thus the triggering of a WARN_ON call trace. This patch
fixes the problem by unreserving the reserved operation when it is
completed.
Fixes: 856cc4c237ad ("IB/hfi1: Add the capability for reserved operations") Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
projects / mirror_ubuntu-bionic-kernel.git / log