When simulate random transfer fail for sdio write and read, it happened
"payload length exceeds max htc length" and recovery later sometimes.
Test steps:
1. Add config and update kernel:
CONFIG_FAIL_MMC_REQUEST=y
CONFIG_FAULT_INJECTION=y
CONFIG_FAULT_INJECTION_DEBUG_FS=y
2. Run simulate fail:
cd /sys/kernel/debug/mmc1/fail_mmc_request
echo 10 > probability
echo 10 > times # repeat until hitting issues
3. It happened payload length exceeds max htc length.
[ 199.935506] ath10k_sdio mmc1:0001:1: payload length 57005 exceeds max htc length: 4088
....
[ 264.990191] ath10k_sdio mmc1:0001:1: payload length 57005 exceeds max htc length: 4088
4. after some time, such as 60 seconds, it start recovery which triggered
by wmi command timeout for periodic scan.
[ 269.229232] ieee80211 phy0: Hardware restart was requested
[ 269.734693] ath10k_sdio mmc1:0001:1: device successfully recovered
The simulate fail of sdio is not a real sdio transter fail, it only
set an error status in mmc_should_fail_request after the transfer end,
actually the transfer is success, then sdio_io_rw_ext_helper will
return error status and stop transfer the left data. For example,
the really RX len is 286 bytes, then it will split to 2 blocks in
sdio_io_rw_ext_helper, one is 256 bytes, left is 30 bytes, if the
first 256 bytes get an error status by mmc_should_fail_request,then
the left 30 bytes will not read in this RX operation. Then when the
next RX arrive, the left 30 bytes will be considered as the header
of the read, the top 4 bytes of the 30 bytes will be considered as
lookaheads, but actually the 4 bytes is not the lookaheads, so the len
from this lookaheads is not correct, it exceeds max htc length 4088
sometimes. When happened exceeds, the buffer chain is not matched between
firmware and ath10k, then it need to start recovery ASAP. Recently then
recovery will be started by wmi command timeout, but it will be long time
later, for example, it is 60+ seconds later from the periodic scan, if
it does not have periodic scan, it will be longer.
Start recovery when it happened "payload length exceeds max htc length"
will be reasonable.
This patch only effect sdio chips.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200108031957.22308-3-wgong@codeaurora.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The realtime bitmap and summary files are regular files that are hidden
away from the directory tree. Since they're regular files, inode
inactivation will try to purge what it thinks are speculative
preallocations beyond the incore size of the file. Unfortunately,
xfs_growfs_rt forgets to update the incore size when it resizes the
inodes, with the result that inactivating the rt inodes at unmount time
will cause their contents to be truncated.
Fix this by updating the incore size when we change the ondisk size as
part of updating the superblock. Note that we don't do this when we're
allocating blocks to the rt inodes because we actually want those blocks
to get purged if the growfs fails.
This fixes corruption complaints from the online rtsummary checker when
running xfs/233. Since that test requires rmap, one can also trigger
this by growing an rt volume, cycling the mount, and creating rt files.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Commit 6f24ff97e323 ("power: supply: bq27xxx_battery: Add the
BQ27Z561 Battery monitor") and commit d74534c27775 ("power:
bq27xxx_battery: Add support for additional bq27xxx family devices")
added support for new device types by copying most of the code and
adding necessary quirks.
However they did not copy the code in bq27xxx_battery_status()
responsible for returning POWER_SUPPLY_STATUS_NOT_CHARGING.
Unify the bq27xxx_battery_status() so for all types when charger is
supplied, it will return "not charging" status.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
This is commit fdfeff0f9e3d ("arm64: hw_breakpoint: Handle inexact
watchpoint addresses") but ported to arm32, which has the same
problem.
This problem was found by Android CTS tests, notably the
"watchpoint_imprecise" test [1]. I tested locally against a copycat
(simplified) version of the test though.
Link: https://lkml.kernel.org/r/20191019111216.1.I82eae759ca6dc28a245b043f485ca490e3015321@changeid Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Matthias Kaehlcke <mka@chromium.org> Acked-by: Will Deacon <will@kernel.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
First problem is we hit BUG_ON() in f2fs_get_sum_page given EIO on
f2fs_get_meta_page_nofail().
Quick fix was not to give any error with infinite loop, but syzbot caught
a case where it goes to that loop from fuzzed image. In turned out we abused
f2fs_get_meta_page_nofail() like in the below call stack.
INFO: task syz-executor178:6870 can't die for more than 143 seconds.
task:syz-executor178 state:R
stack:26960 pid: 6870 ppid: 6869 flags:0x00004006
Call Trace:
Showing all locks held in the system:
1 lock held by khungtaskd/1179:
#0: ffffffff8a554da0 (rcu_read_lock){....}-{1:2}, at: debug_show_all_locks+0x53/0x260 kernel/locking/lockdep.c:6242
1 lock held by systemd-journal/3920:
1 lock held by in:imklog/6769:
#0: ffff88809eebc130 (&f->f_pos_lock){+.+.}-{3:3}, at: __fdget_pos+0xe9/0x100 fs/file.c:930
1 lock held by syz-executor178/6870:
#0: ffff8880925120e0 (&type->s_umount_key#47/1){+.+.}-{3:3}, at: alloc_super+0x201/0xaf0 fs/super.c:229
Actually, we didn't have to use _nofail in this case, since we could return
error to mount(2) already with the error handler.
As a result, this patch tries to 1) remove _nofail callers as much as possible,
2) deal with error case in last remaining caller, f2fs_get_sum_page().
Reported-by: syzbot+ee250ac8137be41d7b13@syzkaller.appspotmail.com Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Currently we overflow save_area_sync and write over
save_area_async. Although this is not a real problem make
startup_pgm_check_handler consistent with late pgm check handler and
store [%r0,%r7] directly into gpregs_save_area.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
@blkno in f2fs_ra_meta_pages could exceed max segment count, causing panic
in following sanity check in current_sit_addr(), add check condition to
avoid this issue.
Reported-by: syzbot+3698081bcf0bb2d12174@syzkaller.appspotmail.com Signed-off-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
In f2fs_lookup(), @res_page could be used before being initialized,
because in __f2fs_find_entry(), once F2FS_I(dir)->i_current_depth was
been fuzzed to zero, then @res_page will never be initialized, causing
this kmsan warning, relocating @res_page initialization place to fix
this bug.
Reported-by: syzbot+0eac6f0bbd558fd866d7@syzkaller.appspotmail.com Signed-off-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The de facto (and apparently uncommented) standard for using an mm had,
thanks to this code in sparc if nothing else, been that you must have a
reference on mm_users *and that reference must have been obtained with
mmget()*, i.e., from a thread with a reference to mm_users that had used
the mm.
The introduction of mmget_not_zero() in commit d2005e3f41d4
("userfaultfd: don't pin the user memory in userfaultfd_file_create()")
allowed mm_count holders to aoperate on user mappings asynchronously
from the actual threads using the mm, but they were not to load those
mappings into their TLB (i.e., walking vmas and page tables is okay,
kthread_use_mm() is not).
io_uring 2b188cc1bb857 ("Add io_uring IO interface") added code which
does a kthread_use_mm() from a mmget_not_zero() refcount.
The problem with this is code which previously assumed mm == current->mm
and mm->mm_users == 1 implies the mm will remain single-threaded at
least until this thread creates another mm_users reference, has now
broken.
arch/sparc/kernel/smp_64.c:
if (atomic_read(&mm->mm_users) == 1) {
cpumask_copy(mm_cpumask(mm), cpumask_of(cpu));
goto local_flush_and_out;
}
vs fs/io_uring.c
if (unlikely(!(ctx->flags & IORING_SETUP_SQPOLL) ||
!mmget_not_zero(ctx->sqo_mm)))
return -EFAULT;
kthread_use_mm(ctx->sqo_mm);
mmget_not_zero() could come in right after the mm_users == 1 test, then
kthread_use_mm() which sets its CPU in the mm_cpumask. That update could
be lost if cpumask_copy() occurs afterward.
I propose we fix this by allowing mmget_not_zero() to be a first-class
reference, and not have this obscure undocumented and unchecked
restriction.
The basic fix for sparc64 is to remove its mm_cpumask clearing code. The
optimisation could be effectively restored by sending IPIs to mm_cpumask
members and having them remove themselves from mm_cpumask. This is more
tricky so I leave it as an exercise for someone with a sparc64 SMP.
powerpc has a (currently similarly broken) example.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200914045219.3736466-4-npiggin@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
powerpc uses IPIs in some situations to switch a kernel thread away
from a lazy tlb mm, which is subject to the TLB flushing race
described in the changelog introducing ARCH_WANT_IRQS_OFF_ACTIVATE_MM.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200914045219.3736466-3-npiggin@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Reading and modifying current->mm and current->active_mm and switching
mm should be done with irqs off, to prevent races seeing an intermediate
state.
This is similar to commit 38cf307c1f20 ("mm: fix kthread_use_mm() vs TLB
invalidate"). At exec-time when the new mm is activated, the old one
should usually be single-threaded and no longer used, unless something
else is holding an mm_users reference (which may be possible).
Absent other mm_users, there is also a race with preemption and lazy tlb
switching. Consider the kernel_execve case where the current thread is
using a lazy tlb active mm:
If we switch back to the kernel thread from a different mm, there is a
double free of the old active_mm, and a missing free of the new one.
Closing this race only requires interrupts to be disabled while ->mm
and ->active_mm are being switched, but the TLB problem requires also
holding interrupts off over activate_mm. Unfortunately not all archs
can do that yet, e.g., arm defers the switch if irqs are disabled and
expects finish_arch_post_lock_switch() to be called to complete the
flush; um takes a blocking lock in activate_mm().
So as a first step, disable interrupts across the mm/active_mm updates
to close the lazy tlb preempt race, and provide an arch option to
extend that to activate_mm which allows architectures doing IPI based
TLB shootdowns to close the second race.
This is a bit ugly, but in the interest of fixing the bug and backporting
before all architectures are converted this is a compromise.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200914045219.3736466-2-npiggin@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
When building with W=1 we get the following warning:
arch/powerpc/platforms/powernv/smp.c: In function ‘pnv_smp_cpu_kill_self’:
arch/powerpc/platforms/powernv/smp.c:276:16: error: suggest braces around
empty body in an ‘if’ statement [-Werror=empty-body]
276 | cpu, srr1);
| ^
cc1: all warnings being treated as errors
The full context is this block:
if (srr1 && !generic_check_cpu_restart(cpu))
DBG("CPU%d Unexpected exit while offline srr1=%lx!\n",
cpu, srr1);
When building with DEBUG undefined DBG() expands to nothing and GCC emits
the warning due to the lack of braces around an empty statement.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200804005410.146094-2-oohall@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
If should_futex_fail() returns true in futex_wake_pi(), then the 'ret'
variable is set to -EFAULT and then immediately overwritten. So the failure
injection is non-functional.
Fix it by actually leaving the function and returning -EFAULT.
The Fixes tag is kinda blury because the initial commit which introduced
failure injection was already sloppy, but the below mentioned commit broke
it completely.
[ tglx: Massaged changelog ]
Fixes: 6b4f4bc9cb22 ("locking/futex: Allow low-level atomic operations to return -EAGAIN") Signed-off-by: Mateusz Nosek <mateusznosek0@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20200927000858.24219-1-mateusznosek0@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
ata_qc_complete_multiple() has to be called with the tags physically
active, that is the hw tag is at bit 0. ap->qc_active has the same tag
at bit ATA_TAG_INTERNAL instead, so call ata_qc_get_active() to fix that
up. This is done in the vein of 8385d756e114 ("libata: Fix retrieving of
active qcs").
Each EMAD transaction stores the skb used to issue the EMAD request
('trans->tx_skb') so that the request could be retried in case of a
timeout. The skb can be freed when a corresponding response is received
or as part of the retry logic (e.g., failed retransmit, exceeded maximum
number of retries).
The two tasks (i.e., response processing and retransmits) are
synchronized by the atomic 'trans->active' field which ensures that
responses to inactive transactions are ignored.
In case of a failed retransmit the transaction is finished and all of
its resources are freed. However, the current code does not mark it as
inactive. Syzkaller was able to hit a race condition in which a
concurrent response is processed while the transaction's resources are
being freed, resulting in a use-after-free [1].
Fix the issue by making sure to mark the transaction as inactive after a
failed retransmit and free its resources only if a concurrent task did
not already do that.
[1]
BUG: KASAN: use-after-free in consume_skb+0x30/0x370
net/core/skbuff.c:833
Read of size 4 at addr ffff88804f570494 by task syz-executor.0/1004
Memory state around the buggy address: ffff88804f570380: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb ffff88804f570400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff88804f570480: fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc fc
^ ffff88804f570500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff88804f570580: 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc fc
Fixes: caf7297e7ab5f ("mlxsw: core: Introduce support for asynchronous EMAD register access") Signed-off-by: Amit Cohen <amcohen@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
GCC 10 optimizes the scheduler code differently than its predecessors.
When CONFIG_DEBUG_SECTION_MISMATCH=y, the Makefile forces GCC not
to inline some functions (-fno-inline-functions-called-once). Before GCC
10, "no-inlined" __schedule() starts with the usual prologue:
push %bp
mov %sp, %bp
So the ORC unwinder simply picks stack pointer from %bp and
unwinds from __schedule() just perfectly:
But now, with GCC 10, there is no %bp prologue in __schedule():
$ cat /proc/1/stack
<nothing>
The ORC entry of the point in __schedule() is:
sp:sp+88 bp:last_sp-48 type:call end:0
In this case, nobody subtracts sizeof "struct inactive_task_frame" in
__unwind_start(). The struct is put on the stack by __switch_to_asm() and
only then __switch_to_asm() stores %sp to task->thread.sp. But we start
unwinding from a point in __schedule() (stored in frame->ret_addr by
'call') and not in __switch_to_asm().
0xffffffff9376cad0 is __schedule+0x1f0 (after the call to
__switch_to_asm). Now follow those 88 bytes from the ORC entry (sp+88).
The entry is correct, __schedule() really pushes 48 bytes (8*7) + 32 bytes
via subq to store some local values (like 4U below). So to unwind, look
at the offset 88-sizeof(long) = 0x50 from here:
Here ^^^^^^^^^^^^^^^^ is the correct ret addr from
__schedule(). It translates to schedule+0x42 (insn after a call to
__schedule()).
BUT, unwind_next_frame() tries to take the address starting from
0xffff94b50001fdc8. That is exactly from thread.sp+88-sizeof(long) =
0xffff94b50001fdc8+88-8 = 0xffff94b50001fe18, which is garbage marked as
NOTE above. So this quits the unwinding as 7793fab6956b2d00 is obviously
not a kernel address.
There was a fix to skip 'struct inactive_task_frame' in
unwind_get_return_address_ptr in the following commit:
187b96db5ca7 ("x86/unwind/orc: Fix unwind_get_return_address_ptr() for inactive tasks")
But we need to skip the struct already in the unwinder proper. So
subtract the size (increase the stack pointer) of the structure in
__unwind_start() directly. This allows for removal of the code added by
commit 187b96db5ca7 completely, as the address is now at
'(unsigned long *)state->sp - 1', the same as in the generic case.
[ mingo: Cleaned up the changelog a bit, for better readability. ]
Few commands provide the list of description partially and require
to be called consecutively until all the descriptors are fetched
completely. In such cases, we don't release the buffers and reuse
them for consecutive transmits.
However, currently we don't reset the Rx size which will be set as
per the response for the last transmit. This may result in incorrect
response size being interpretted as the firmware may repond with size
greater than the one set but we read only upto the size set by previous
response.
Let us reset the receive buffer size to max possible in such cases as
we don't know the exact size of the response.
Link: https://lore.kernel.org/r/20201012141746.32575-1-sudeep.holla@arm.com Fixes: b6f20ff8bd94 ("firmware: arm_scmi: add common infrastructure and support for base protocol") Reported-by: Etienne Carriere <etienne.carriere@linaro.org> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
In order to avoid high dom0 load due to rogue guests sending events at
high frequency, block those events in case there was no action needed
in dom0 to handle the events.
This is done by adding a per-event counter, which set to zero in case
an EOI without the XEN_EOI_FLAG_SPURIOUS is received from a backend
driver, and incremented when this flag has been set. In case the
counter is 2 or higher delay the EOI by 1 << (cnt - 2) jiffies, but
not more than 1 second.
In order not to waste memory shorten the per-event refcnt to two bytes
(it should normally never exceed a value of 2). Add an overflow check
to evtchn_get() to make sure the 2 bytes really won't overflow.
This is part of XSA-332.
Cc: stable@vger.kernel.org Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Stefano Stabellini <sstabellini@kernel.org> Reviewed-by: Wei Liu <wl@xen.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
In case rogue guests are sending events at high frequency it might
happen that xen_evtchn_do_upcall() won't stop processing events in
dom0. As this is done in irq handling a crash might be the result.
In order to avoid that, delay further inter-domain events after some
time in xen_evtchn_do_upcall() by forcing eoi processing into a
worker on the same cpu, thus inhibiting new events coming in.
The time after which eoi processing is to be delayed is configurable
via a new module parameter "event_loop_timeout" which specifies the
maximum event loop time in jiffies (default: 2, the value was chosen
after some tests showing that a value of 2 was the lowest with an
only slight drop of dom0 network throughput while multiple guests
performed an event storm).
How long eoi processing will be delayed can be specified via another
parameter "event_eoi_delay" (again in jiffies, default 10, again the
value was chosen after testing with different delay values).
Today only fifo event channels have a cpu hotplug callback. In order
to prepare for more percpu (de)init work move that callback into
events_base.c and add percpu_init() and percpu_deinit() hooks to
struct evtchn_ops.
This is part of XSA-332.
Cc: stable@vger.kernel.org Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Wei Liu <wl@xen.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
In order to reduce the chance for the system becoming unresponsive due
to event storms triggered by a misbehaving pcifront use the lateeoi irq
binding for pciback and unmask the event channel only just before
leaving the event handling function.
Restructure the handling to support that scheme. Basically an event can
come in for two reasons: either a normal request for a pciback action,
which is handled in a worker, or in case the guest has finished an AER
request which was requested by pciback.
When an AER request is issued to the guest and a normal pciback action
is currently active issue an EOI early in order to be able to receive
another event when the AER request has been finished by the guest.
Let the worker processing the normal requests run until no further
request is pending, instead of starting a new worker ion that case.
Issue the EOI only just before leaving the worker.
This scheme allows to drop calling the generic function
xen_pcibk_test_and_schedule_op() after processing of any request as
the handling of both request types is now separated more cleanly.
This is part of XSA-332.
Cc: stable@vger.kernel.org Reported-by: Julien Grall <julien@xen.org> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Wei Liu <wl@xen.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
In order to reduce the chance for the system becoming unresponsive due
to event storms triggered by a misbehaving pvcallsfront use the lateeoi
irq binding for pvcallsback and unmask the event channel only after
handling all write requests, which are the ones coming in via an irq.
This requires modifying the logic a little bit to not require an event
for each write request, but to keep the ioworker running until no
further data is found on the ring page to be processed.
In order to reduce the chance for the system becoming unresponsive due
to event storms triggered by a misbehaving scsifront use the lateeoi
irq binding for scsiback and unmask the event channel only just before
leaving the event handling function.
In case of a ring protocol error don't issue an EOI in order to avoid
the possibility to use that for producing an event storm. This at once
will result in no further call of scsiback_irq_fn(), so the ring_error
struct member can be dropped and scsiback_do_cmd_fn() can signal the
protocol error via a negative return value.
This is part of XSA-332.
Cc: stable@vger.kernel.org Reported-by: Julien Grall <julien@xen.org> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Wei Liu <wl@xen.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
In order to reduce the chance for the system becoming unresponsive due
to event storms triggered by a misbehaving netfront use the lateeoi
irq binding for netback and unmask the event channel only just before
going to sleep waiting for new events.
Make sure not to issue an EOI when none is pending by introducing an
eoi_pending element to struct xenvif_queue.
When no request has been consumed set the spurious flag when sending
the EOI for an interrupt.
This is part of XSA-332.
Cc: stable@vger.kernel.org Reported-by: Julien Grall <julien@xen.org> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Wei Liu <wl@xen.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
In order to reduce the chance for the system becoming unresponsive due
to event storms triggered by a misbehaving blkfront use the lateeoi
irq binding for blkback and unmask the event channel only after
processing all pending requests.
As the thread processing requests is used to do purging work in regular
intervals an EOI may be sent only after having received an event. If
there was no pending I/O request flag the EOI as spurious.
This is part of XSA-332.
Cc: stable@vger.kernel.org Reported-by: Julien Grall <julien@xen.org> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Wei Liu <wl@xen.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
In order to avoid tight event channel related IRQ loops add a new
framework of "late EOI" handling: the IRQ the event channel is bound
to will be masked until the event has been handled and the related
driver is capable to handle another event. The driver is responsible
for unmasking the event channel via the new function xen_irq_lateeoi().
This is similar to binding an event channel to a threaded IRQ, but
without having to structure the driver accordingly.
In order to support a future special handling in case a rogue guest
is sending lots of unsolicited events, add a flag to xen_irq_lateeoi()
which can be set by the caller to indicate the event was a spurious
one.
This is part of XSA-332.
Cc: stable@vger.kernel.org Reported-by: Julien Grall <julien@xen.org> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Stefano Stabellini <sstabellini@kernel.org> Reviewed-by: Wei Liu <wl@xen.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
A follow-up patch will require certain write to happen before an event
channel is unmasked.
While the memory barrier is not strictly necessary for all the callers,
the main one will need it. In order to avoid an extra memory barrier
when using fifo event channels, mandate evtchn_unmask() to provide
write ordering.
The 2-level event handling unmask operation is missing an appropriate
barrier, so add it. Fifo event channels are fine in this regard due to
using sync_cmpxchg().
Today it can happen that an event channel is being removed from the
system while the event handling loop is active. This can lead to a
race resulting in crashes or WARN() splats when trying to access the
irq_info structure related to the event channel.
Fix this problem by using a rwlock taken as reader in the event
handling loop and as writer when deallocating the irq_info structure.
As the observed problem was a NULL dereference in evtchn_from_irq()
make this function more robust against races by testing the irq_info
pointer to be not NULL before dereferencing it.
And finally make all accesses to evtchn_to_irq[row][col] atomic ones
in order to avoid seeing partial updates of an array element in irq
handling. Note that irq handling can be entered only for event channels
which have been valid before, so any not populated row isn't a problem
in this regard, as rows are only ever added and never removed.
This is XSA-331.
Cc: stable@vger.kernel.org Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Reported-by: Jinoh Kang <luke1337@theori.io> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Stefano Stabellini <sstabellini@kernel.org> Reviewed-by: Wei Liu <wl@xen.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Driver ->power_on and ->power_off callbacks leaks internal SMCC firmware
return codes to phy caller. This patch converts SMCC error codes to
standard linux errno codes. Include file linux/arm-smccc.h already provides
defines for SMCC error codes, so use them instead of custom driver defines.
Note that return value is signed 32bit, but stored in unsigned long type
with zero padding.
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Link: https://lore.kernel.org/r/20200902144344.16684-2-pali@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
A build failure was raised by kbuild with the following error.
drivers/android/binder.c: Assembler messages:
drivers/android/binder.c:3861: Error: unrecognized keyword/register name `l.lwz ?ap,4(r24)'
drivers/android/binder.c:3866: Error: unrecognized keyword/register name `l.addi ?ap,r0,0'
The issue is with 64-bit get_user() calls on openrisc. I traced this to
a problem where in the internally in the get_user macros there is a cast
to long __gu_val this causes GCC to think the get_user call is 32-bit.
This binder code is really long and GCC allocates register r30, which
triggers the issue. The 64-bit get_user asm tries to get the 64-bit pair
register, which for r30 overflows the general register names and returns
the dummy register ?ap.
The fix here is to move the temporary variables into the asm macros. We
use a 32-bit __gu_tmp for 32-bit and smaller macro and a 64-bit tmp in
the 64-bit macro. The cast in the 64-bit macro has a trick of casting
through __typeof__((x)-(x)) which avoids the below warning. This was
barrowed from riscv.
arch/openrisc/include/asm/uaccess.h:240:8: warning: cast to pointer from integer of different size
I tested this in a small unit test to check reading between 64-bit and
32-bit pointers to 64-bit and 32-bit values in all combinations. Also I
ran make C=1 to confirm no new sparse warnings came up. It all looks
clean to me.
Link: https://lore.kernel.org/lkml/202008200453.ohnhqkjQ%25lkp@intel.com/ Signed-off-by: Stafford Horne <shorne@gmail.com> Reviewed-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
There seems to be a bug in the original code when gntdev_get_page()
is called with writeable=true then the page needs to be marked dirty
before being put.
To address this, a bool writeable is added in gnt_dev_copy_batch, set
it in gntdev_grant_copy_seg() (and drop `writeable` argument to
gntdev_get_page()) and then, based on batch->writeable, use
set_page_dirty_lock().
Fixes: a4cdb556cae0 (xen/gntdev: add ioctl for grant copy) Suggested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Juergen Gross <jgross@suse.com> Cc: David Vrabel <david.vrabel@citrix.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/1599375114-32360-1-git-send-email-jrdr.linux@gmail.com Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Before commit 9495b7e92f716ab2 ("driver core: platform: Initialize
dma_parms for platform devices"), the R-Car SATA device didn't have DMA
parameters. Hence the DMA boundary mask supplied by its driver was
silently ignored, as __scsi_init_queue() doesn't check the return value
of dma_set_seg_boundary(), and the default value of 0xffffffff was used.
Now the device has gained DMA parameters, the driver-supplied value is
used, and the following warning is printed on Salvator-XS:
DMA-API: sata_rcar ee300000.sata: mapping sg segment across boundary [start=0x00000000ffffe000] [end=0x00000000ffffefff] [boundary=0x000000001ffffffe]
WARNING: CPU: 5 PID: 38 at kernel/dma/debug.c:1233 debug_dma_map_sg+0x298/0x300
(the range of start/end values depend on whether IOMMU support is
enabled or not)
The issue here is that SATA_RCAR_DMA_BOUNDARY doesn't have bit 0 set, so
any typical end value, which is odd, will trigger the check.
Fix this by increasing the DMA boundary value by 1.
This also fixes the following WRITE DMA EXT timeout issue:
Commit 8234f6734c5d ("PM-runtime: Switch autosuspend over to using
hrtimers") switched PM runtime autosuspend to use hrtimers and all
related time accounting in ns, but missed to update the timer_expires
data type in struct dev_pm_info to u64.
This causes the timer_expires value to be truncated on 32-bit
architectures when assignment is done from u64 values:
The issue being that CPU0 takes 'port_lock' on the irq path in pl011_int()
before taking 'console_owner' on the printk() path, whereas CPU1 takes
the two locks in the opposite order on the printk() path due to setting
the "console_owner" prior to calling into into the actual console driver.
Fix this in the same way as the msm-serial driver by dropping 'port_lock'
before handling the sysrq.
Cc: <stable@vger.kernel.org> # 4.19+ Cc: Russell King <linux@armlinux.org.uk> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jirislaby@kernel.org> Link: https://lore.kernel.org/r/20200811101313.GA6970@willie-the-truck Signed-off-by: Peter Zijlstra <peterz@infradead.org> Tested-by: Will Deacon <will@kernel.org> Signed-off-by: Will Deacon <will@kernel.org> Link: https://lore.kernel.org/r/20200930120432.16551-1-will@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
For QUP IP versions 2.5 and above the oversampling rate is
halved from 32 to 16.
Commit ce734600545f ("tty: serial: qcom_geni_serial: Update
the oversampling rate") is pushed to handle this scenario.
But the existing logic is failing to classify QUP Version 3.0
into the correct group ( 2.5 and above).
As result Serial Engine clocks are not configured properly for
baud rate and garbage data is sampled to FIFOs from the line.
So, fix the logic to detect QUP with versions 2.5 and above.
Fixes: ce734600545f ("tty: serial: qcom_geni_serial: Update the oversampling rate") Cc: stable <stable@vger.kernel.org> Signed-off-by: Paras Sharma <parashar@codeaurora.org> Reviewed-by: Akash Asthana <akashast@codeaurora.org> Link: https://lore.kernel.org/r/1601445926-23673-1-git-send-email-parashar@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
process_one_req() // again
req->callback() // BOOM
cancel_delayed_work_sync()
The solution is to always cancel the work once it is completed so any
in between set_timeout() does not result in it running again.
Cc: stable@vger.kernel.org Fixes: 44e75052bc2a ("RDMA/rdma_cm: Make rdma_addr_cancel into a fence") Link: https://lore.kernel.org/r/20200930072007.1009692-1-leon@kernel.org Reported-by: Dan Aloni <dan@kernelim.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
In p54p_tx(), skb->data is mapped to streaming DMA on line 337:
mapping = pci_map_single(..., skb->data, ...);
Then skb->data is accessed on line 349:
desc->device_addr = ((struct p54_hdr *)skb->data)->req_id;
This access may cause data inconsistency between CPU cache and hardware.
To fix this problem, ((struct p54_hdr *)skb->data)->req_id is stored in
a local variable before DMA mapping, and then the driver accesses this
local variable instead of skb->data.
Cc: <stable@vger.kernel.org> Signed-off-by: Jia-Ju Bai <baijiaju@tsinghua.edu.cn> Acked-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200802132949.26788-1-baijiaju@tsinghua.edu.cn Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
This patch checks the size for the EVM_IMA_XATTR_DIGSIG and
EVM_XATTR_PORTABLE_DIGSIG types to ensure that the algorithm is read from
the buffer returned by vfs_getxattr_alloc().
After unlock_request() pages from the ap->pages[] array may be put (e.g. by
aborting the connection) and the pages can be freed.
Prevent use after free by grabbing a reference to the page before calling
unlock_request().
The original patch was created by Pradeep P V K.
Reported-by: Pradeep P V K <ppvk@codeaurora.org> Cc: <stable@vger.kernel.org> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Older ATF does not provide SMC call for SATA phy power on functionality and
therefore initialization of ahci_mvebu is failing when older version of ATF
is using. In this case phy_power_on() function returns -EOPNOTSUPP.
This patch adds a new hflag AHCI_HFLAG_IGN_NOTSUPP_POWER_ON which cause
that ahci_platform_enable_phys() would ignore -EOPNOTSUPP errors from
phy_power_on() call.
It fixes initialization of ahci_mvebu on Espressobin boards where is older
Marvell's Arm Trusted Firmware without SMC call for SATA phy power.
This is regression introduced in commit 8e18c8e58da64 ("arm64: dts: marvell:
armada-3720-espressobin: declare SATA PHY property") where SATA phy was
defined and therefore ahci_platform_enable_phys() on Espressobin started
failing.
Fixes: 8e18c8e58da64 ("arm64: dts: marvell: armada-3720-espressobin: declare SATA PHY property") Signed-off-by: Pali Rohár <pali@kernel.org> Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Cc: <stable@vger.kernel.org> # 5.1+: ea17a0f153af: phy: marvell: comphy: Convert internal SMCC firmware return codes to errno Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Stephane Eranian found a bug in that IBS' current Fetch counter was not
being reset when the driver would write the new value to clear it along
with the enable bit set, and found that adding an MSR write that would
first disable IBS Fetch would make IBS Fetch reset its current count.
Indeed, the PPR for AMD Family 17h Model 31h B0 55803 Rev 0.54 - Sep 12,
2019 states "The periodic fetch counter is set to IbsFetchCnt [...] when
IbsFetchEn is changed from 0 to 1."
Explicitly set IbsFetchEn to 0 and then to 1 when re-enabling IBS Fetch,
so the driver properly resets the internal counter to 0 and IBS
Fetch starts counting again.
A family 15h machine tested does not have this problem, and the extra
wrmsr is also not needed on Family 19h, so only do the extra wrmsr on
families 16h through 18h.
Reported-by: Stephane Eranian <stephane.eranian@google.com> Signed-off-by: Kim Phillips <kim.phillips@amd.com>
[peterz: optimized] Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://bugzilla.kernel.org/show_bug.cgi?id=206537 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Don't recheck it since xattr_permission() already
checks CAP_SYS_ADMIN capability.
Just follow 5d3ce4f70172 ("f2fs: avoid duplicated permission check for "trusted." xattrs")
Reported-by: Hongyu Jin <hongyu.jin@unisoc.com>
[ Gao Xiang: since it could cause some complex Android overlay
permission issue as well on android-5.4+, it'd be better to
backport to 5.4+ rather than pure cleanup on mainline. ] Cc: <stable@vger.kernel.org> # 5.4+ Link: https://lore.kernel.org/r/20200811070020.6339-1-hsiangkao@redhat.com Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Gao Xiang <hsiangkao@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
As part of the commit b148bb238c02
("bnxt_en: Fix possible crash in bnxt_fw_reset_task()."),
cancel_delayed_work_sync() is called only for VFs to fix a possible
crash by cancelling any pending delayed work items. It was assumed
by mistake that the flush_workqueue() call on the PF would flush
delayed work items as well.
As flush_workqueue() does not cancel the delayed workqueue, extend
the fix for PFs. This fix will avoid the system crash, if there are
any pending delayed work items in fw_reset_task() during driver's
.remove() call.
Unify the workqueue cleanup logic for both PF and VF by calling
cancel_work_sync() and cancel_delayed_work_sync() directly in
bnxt_remove_one().
Fixes: b148bb238c02 ("bnxt_en: Fix possible crash in bnxt_fw_reset_task().") Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Reviewed-by: Andy Gospodarek <gospo@broadcom.com> Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
A recent patch has moved the workqueue cleanup logic before
calling unregister_netdev() in bnxt_remove_one(). This caused a
regression because the workqueue can be restarted if the device is
still open. Workqueue cleanup must be done after unregister_netdev().
The workqueue will not restart itself after the device is closed.
Call bnxt_cancel_sp_work() after unregister_netdev() and
call bnxt_dl_fw_reporters_destroy() after that. This fixes the
regession and the original NULL ptr dereference issue.
Fixes: b16939b59cc0 ("bnxt_en: Fix NULL ptr dereference crash in bnxt_fw_reset_task()") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
When a PCIe fatal error occurs, the internal latched BAR addresses
in the chip get reset even though the BAR register values in config
space are retained.
pci_restore_state() will not rewrite the BAR addresses if the
BAR address values are valid, causing the chip's internal BAR addresses
to stay invalid. So we need to zero the BAR registers during PCIe fatal
error to force pci_restore_state() to restore the BAR addresses. These
write cycles to the BAR registers will cause the proper BAR addresses to
latch internally.
Fixes: 6316ea6db93d ("bnxt_en: Enable AER support.") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
It looks like the BAR memory region had already been unmapped before we
start clearing CMDQ registers in it, which is pretty bad and the kernel
happily kills itself because of a Current EL Data Abort (on arm64).
Moving the CMDQ uninitialization a bit early fixes the issue for me.
Fixes: 862d969a3a4d ("net: hns3: do VF's pci re-initialization while PF doing FLR") Signed-off-by: Zenghui Yu <yuzenghui@huawei.com> Link: https://lore.kernel.org/r/20201023051550.793-1-yuzenghui@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Commit ed42989eab57 ("tipc: fix the skb_unshare() in tipc_buf_append()")
replaced skb_unshare() with skb_copy() to not reduce the data reference
counter of the original skb intentionally. This is not the correct
way to handle the cloned skb because it causes memory leak in 2
following cases:
1/ Sending multicast messages via broadcast link
The original skb list is cloned to the local skb list for local
destination. After that, the data reference counter of each skb
in the original list has the value of 2. This causes each skb not
to be freed after receiving ACK:
tipc_link_advance_transmq()
{
...
/* release skb */
__skb_unlink(skb, &l->transmq);
kfree_skb(skb); <-- memory exists after being freed
}
2/ Sending multicast messages via replicast link
Similar to the above case, each skb cannot be freed after purging
the skb list:
tipc_mcast_xmit()
{
...
__skb_queue_purge(pkts); <-- memory exists after being freed
}
This commit fixes this issue by using skb_unshare() instead. Besides,
to avoid use-after-free error reported by KASAN, the pointer to the
fragment is set to NULL before calling skb_unshare() to make sure that
the original skb is not freed after freeing the fragment 2 times in
case skb_unshare() returns NULL.
Fixes: ed42989eab57 ("tipc: fix the skb_unshare() in tipc_buf_append()") Acked-by: Jon Maloy <jmaloy@redhat.com> Reported-by: Thang Hoang Ngo <thang.h.ngo@dektech.com.au> Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au> Reviewed-by: Xin Long <lucien.xin@gmail.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Link: https://lore.kernel.org/r/20201027032403.1823-1-tung.q.nguyen@dektech.com.au Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
With SO_RCVLOWAT, under memory pressure,
it is possible to enter a state where:
1. We have not received enough bytes to satisfy SO_RCVLOWAT.
2. We have not entered buffer pressure (see tcp_rmem_pressure()).
3. But, we do not have enough buffer space to accept more packets.
In this case, we advertise 0 rwnd (due to #3) but the application does
not drain the receive queue (no wakeup because of #1 and #2) so the
flow stalls.
Modify the heuristic for SO_RCVLOWAT so that, if we are advertising
rwnd<=rcv_mss, force a wakeup to prevent a stall.
Without this patch, setting tcp_rmem to 6143 and disabling TCP
autotune causes a stalled flow. With this patch, no stall occurs. This
is with RPC-style traffic with large messages.
Fixes: 03f45c883c6f ("tcp: avoid extra wakeups for SO_RCVLOWAT users") Signed-off-by: Arjun Roy <arjunroy@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20201023184709.217614-1-arjunroy.kdev@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
In the function ravb_hwtstamp_get() in ravb_main.c with the existing
values for RAVB_RXTSTAMP_TYPE_V2_L2_EVENT (0x2) and RAVB_RXTSTAMP_TYPE_ALL
(0x6)
if (priv->tstamp_rx_ctrl & RAVB_RXTSTAMP_TYPE_V2_L2_EVENT)
config.rx_filter = HWTSTAMP_FILTER_PTP_V2_L2_EVENT;
else if (priv->tstamp_rx_ctrl & RAVB_RXTSTAMP_TYPE_ALL)
config.rx_filter = HWTSTAMP_FILTER_ALL;
if the test on RAVB_RXTSTAMP_TYPE_ALL should be true,
it will never be reached.
This issue can be verified with 'hwtstamp_config' testing program
(tools/testing/selftests/net/hwtstamp_config.c). Setting filter type
to ALL and subsequent retrieving it gives incorrect value:
$ hwtstamp_config eth0 OFF ALL
flags = 0
tx_type = OFF
rx_filter = ALL
$ hwtstamp_config eth0
flags = 0
tx_type = OFF
rx_filter = PTP_V2_L2_EVENT
Correct this by converting if-else's to switch.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper") Reported-by: Julia Lawall <julia.lawall@inria.fr> Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com> Link: https://lore.kernel.org/r/20201026102130.29368-1-andrew_gabbasov@mentor.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
As reported by Serge flag IRQF_NO_THREAD causes an error if the
interrupt is actually shared and the other driver(s) don't have this
flag set. This situation can occur if a PCI(e) legacy interrupt is
used in combination with forced threading.
There's no good way to deal with this properly, therefore we have to
remove flag IRQF_NO_THREAD. For fixing the original forced threading
issue switch to napi_schedule().
Guillaume Nault [Mon, 26 Oct 2020 10:29:45 +0000 (11:29 +0100)]
net/sched: act_mpls: Add softdep on mpls_gso.ko
BugLink: https://bugs.launchpad.net/bugs/1904445
TCA_MPLS_ACT_PUSH and TCA_MPLS_ACT_MAC_PUSH might be used on gso
packets. Such packets will thus require mpls_gso.ko for segmentation.
v2: Drop dependency on CONFIG_NET_MPLS_GSO in Kconfig (from Jakub and
David).
Fixes: 2a2ea50870ba ("net: sched: add mpls manipulation actions to TC") Signed-off-by: Guillaume Nault <gnault@redhat.com> Link: https://lore.kernel.org/r/1f6cab15bbd15666795061c55563aaf6a386e90e.1603708007.git.gnault@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Currently it is possible to craft a special netlink RTM_NEWQDISC
command that can result in jitter being equal to 0x80000000. It is
enough to set the 32 bit jitter to 0x02000000 (it will later be
multiplied by 2^6) or just set the 64 bit jitter via
TCA_NETEM_JITTER64. This causes an overflow during the generation of
uniformly distributed numbers in tabledist(), which in turn leads to
division by zero (sigma != 0, but sigma * 2 is 0).
The related fragment of code needs 32-bit division - see commit 9b0ed89 ("netem: remove unnecessary 64 bit modulus"), so switching to
64 bit is not an option.
Fix the issue by keeping the value of jitter within the range that can
be adequately handled by tabledist() - [0;INT_MAX]. As negative std
deviation makes no sense, take the absolute value of the passed value
and cap it at INT_MAX. Inside tabledist(), switch to unsigned 32 bit
arithmetic in order to prevent overflows.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Aleksandr Nogikh <nogikh@google.com> Reported-by: syzbot+ec762a6342ad0d3c0d8f@syzkaller.appspotmail.com Acked-by: Stephen Hemminger <stephen@networkplumber.org> Link: https://lore.kernel.org/r/20201028170731.1383332-1-aleksandrnogikh@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Jakub Kicinski brought up a concern in ibmvnic_set_mac().
ibmvnic_set_mac() does this:
ether_addr_copy(adapter->mac_addr, addr->sa_data);
if (adapter->state != VNIC_PROBED)
rc = __ibmvnic_set_mac(netdev, addr->sa_data);
So if state == VNIC_PROBED, the user can assign an invalid address to
adapter->mac_addr, and ibmvnic_set_mac() will still return 0.
The fix is to validate ethernet address at the beginning of
ibmvnic_set_mac(), and move the ether_addr_copy to
the case of "adapter->state != VNIC_PROBED".
Fixes: c26eba03e407 ("ibmvnic: Update reset infrastructure to support tunable parameters") Signed-off-by: Lijun Pan <ljp@linux.ibm.com> Link: https://lore.kernel.org/r/20201027220456.71450-1-ljp@linux.ibm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The current code sets up the filter action field before
rewrites are set up. When the action 'switch' is used
with rewrites, this may result in initial few packets
that get switched out don't have rewrites applied
on them.
So, make sure filter action is set up along with rewrites
or only after everything else is set up for rewrites.
Fixes: 12b276fbf6e0 ("cxgb4: add support to create hash filters") Signed-off-by: Raju Rangoju <rajur@chelsio.com> Link: https://lore.kernel.org/r/20201023115852.18262-1-rajur@chelsio.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
chtls_pt_recvmsg() receives a skb with tls header and subsequent
skb with data, need to finalize the data copy whenever next skb
with tls header is available. but here current tls header is
overwritten by next available tls header, ends up corrupting
user buffer data. fixing it by finalizing current record whenever
next skb contains tls header.
v1->v2:
- Improved commit message.
Fixes: 17a7d24aa89d ("crypto: chtls - generic handling of data and hdr") Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com> Link: https://lore.kernel.org/r/20201022190556.21308-1-vinay.yadav@chelsio.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
CPL handler functions chtls_pass_open_rpl() and
chtls_close_listsrv_rpl() should return CPL_RET_BUF_DONE
so that caller function will do skb free to avoid leak.
In chtls_pass_establish() we hold child socket lock using bh_lock_sock
and we are again trying bh_lock_sock in add_to_reap_list, causing deadlock.
Remove bh_lock_sock in add_to_reap_list() as lock is already held.
In the AER or firmware reset flow, if we are in fatal error state or
if pci_channel_offline() is true, we don't send any commands to the
firmware because the commands will likely not reach the firmware and
most commands don't matter much because the firmware is likely to be
reset imminently.
However, the HWRM_FUNC_RESET command is different and we should always
attempt to send it. In the AER flow for example, the .slot_reset()
call will trigger this fw command and we need to try to send it to
effect the proper reset.
Fixes: b340dc680ed4 ("bnxt_en: Avoid sending firmware messages when AER error is detected.") Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
bnxt_open_nic() is called during configuration changes that require
the NIC to be closed and then opened. This call is protected by
rtnl_lock. Firmware reset can be happening at the same time. Only
critical portions of the entire firmware reset sequence are protected
by the rtnl_lock. It is possible that bnxt_open_nic() can be called
when the firmware reset sequence is aborting. In that case,
bnxt_open_nic() needs to check if the ABORT_ERR flag is set and
abort if it is. The configuration change that resulted in the
bnxt_open_nic() call will fail but the NIC will be brought to a
consistent IF_DOWN state.
Without this patch, if bnxt_open_nic() were to continue in this error
state, it may crash like this:
Fix build error when CONFIG_ACPI is not set/enabled by adding the header
file <asm/acpi.h> which contains a stub for the function in the build
error.
../arch/x86/pci/intel_mid_pci.c: In function ‘intel_mid_pci_init’:
../arch/x86/pci/intel_mid_pci.c:303:2: error: implicit declaration of function ‘acpi_noirq_set’; did you mean ‘acpi_irq_get’? [-Werror=implicit-function-declaration]
acpi_noirq_set();
Fixes: a912a7584ec3 ("x86/platform/intel-mid: Move PCI initialization to arch_init()") Link: https://lore.kernel.org/r/ea903917-e51b-4cc9-2680-bc1e36efa026@infradead.org Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Jesse Barnes <jsbarnes@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org # v4.16+ Cc: Jacob Pan <jacob.jun.pan@linux.intel.com> Cc: Len Brown <lenb@kernel.org> Cc: Jesse Barnes <jsbarnes@google.com> Cc: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
With CONFIG_EXPERT=y, CONFIG_KASAN=y, CONFIG_RANDOMIZE_BASE=n,
CONFIG_RELOCATABLE=n, we observe the following failure when trying to
link the kernel image with LD=ld.lld:
error: section: .exit.data is not contiguous with other relro sections
ld.lld defaults to -z relro while ld.bfd defaults to -z norelro. This
was previously fixed, but only for CONFIG_RELOCATABLE=y.
Fixes: 3bbd3db86470 ("arm64: relocatable: fix inconsistencies in linker script and options") Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20201016175339.2429280-1-ndesaulniers@google.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Commit 606f8e7b27bf ("arm64: capabilities: Use linear array for
detection and verification") changed the way we deal with per-CPU errata
by only calling the .matches() callback until one CPU is found to be
affected. At this point, .matches() stop being called, and .cpu_enable()
will be called on all CPUs.
This breaks the ARCH_WORKAROUND_2 handling, as only a single CPU will be
mitigated.
In order to address this, forcefully call the .matches() callback from a
.cpu_enable() callback, which brings us back to the original behaviour.
Fixes: 606f8e7b27bf ("arm64: capabilities: Use linear array for detection and verification") Cc: <stable@vger.kernel.org> Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Commit 73f381660959 ("arm64: Advertise mitigation of Spectre-v2, or lack
thereof") changed the way we deal with ARCH_WORKAROUND_1, by moving most
of the enabling code to the .matches() callback.
This has the unfortunate effect that the workaround gets only enabled on
the first affected CPU, and no other.
In order to address this, forcefully call the .matches() callback from a
.cpu_enable() callback, which brings us back to the original behaviour.
Fixes: 73f381660959 ("arm64: Advertise mitigation of Spectre-v2, or lack thereof") Cc: <stable@vger.kernel.org> Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
When building for an embedded target using Yocto, we're sometimes
observing that the version string that gets built into vmlinux (and
thus what uname -a reports) differs from the path under /lib/modules/
where modules get installed in the rootfs, but only in the length of
the -gabc123def suffix. Hence modprobe always fails.
The problem is that Yocto has the concept of "sstate" (shared state),
which allows different developers/buildbots/etc. to share build
artifacts, based on a hash of all the metadata that went into building
that artifact - and that metadata includes all dependencies (e.g. the
compiler used etc.). That normally works quite well; usually a clean
build (without using any sstate cache) done by one developer ends up
being binary identical to a build done on another host. However, one
thing that can cause two developers to end up with different builds
[and thus make one's vmlinux package incompatible with the other's
kernel-dev package], which is not captured by the metadata hashing, is
this `git describe`: The output of that can be affected by
(1) git version: before 2.11 git defaulted to a minimum of 7, since
2.11 (git.git commit e6c587) the default is dynamic based on the
number of objects in the repo
(2) hence even if both run the same git version, the output can differ
based on how many remotes are being tracked (or just lots of local
development branches or plain old garbage)
(3) and of course somebody could have a core.abbrev config setting in
~/.gitconfig
So in order to avoid `uname -a` output relying on such random details
of the build environment which are rather hard to ensure are
consistent between developers and buildbots, make sure the abbreviated
sha1 always consists of exactly 12 hex characters. That is consistent
with the current rule for -stable patches, and is almost always enough
to identify the head commit unambigously - in the few cases where it
does not, the v5.4.3-00021- prefix would certainly nail it down.
[Adapt to `` vs $() differences between 5.4 and upstream.] Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
When compiling the kernel with AS=clang, objtool produces a lot of
warnings:
warning: objtool: missing symbol for section .text
warning: objtool: missing symbol for section .init.text
warning: objtool: missing symbol for section .ref.text
It then fails to generate the ORC table.
The problem is that objtool assumes text section symbols always exist.
But the Clang assembler is aggressive about removing them.
When generating relocations for the ORC table, objtool always tries to
reference instructions by their section symbol offset. If the section
symbol doesn't exist, it bails.
Do a fallback: when a section symbol isn't available, reference a
function symbol instead.
Reported-by: Dmitry Golovin <dima@golovin.in> Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Borislav Petkov <bp@suse.de> Tested-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Miroslav Benes <mbenes@suse.cz> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://github.com/ClangBuiltLinux/linux/issues/669 Link: https://lkml.kernel.org/r/9a9cae7fcf628843aabe5a086b1a3c5bf50f42e8.1585761021.git.jpoimboe@redhat.com Cc: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
SOCK_TSTAMP_NEW (timespec64 instead of timespec) is also used for
hardware time stamps (configured via SO_TIMESTAMPING_NEW).
User space (ptp4l) first configures hardware time stamping via
SO_TIMESTAMPING_NEW which sets SOCK_TSTAMP_NEW. In the next step, ptp4l
disables SO_TIMESTAMPNS(_NEW) (software time stamps), but this must not
switch hardware time stamps back to "32 bit mode".
This problem happens on 32 bit platforms were the libc has already
switched to struct timespec64 (from SO_TIMExxx_OLD to SO_TIMExxx_NEW
socket options). ptp4l complains with "missing timestamp on transmitted
peer delay request" because the wrong format is received (and
discarded).
Fixes: 887feae36aee ("socket: Add SO_TIMESTAMP[NS]_NEW") Fixes: 783da70e8396 ("net: add sock_enable_timestamps") Signed-off-by: Christian Eggers <ceggers@arri.de> Acked-by: Willem de Bruijn <willemb@google.com> Acked-by: Deepa Dinamani <deepa.kernel@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
BUG: KASAN: slab-out-of-bounds in nft_flow_rule_create+0x622/0x6a2
net/netfilter/nf_tables_offload.c:40
Read of size 8 at addr ffff888103910b58 by task syz-executor227/16244
The error happens when expr->ops is accessed early on before performing the boundary check and after nft_expr_next() moves the expr to go out-of-bounds.
This patch checks the boundary condition before expr->ops that fixes the slab-out-of-bounds Read issue.
Add nft_expr_more() and use it to fix this problem.
Signed-off-by: Saeed Mirzamohammadi <saeed.mirzamohammadi@oracle.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
fs/btrfs/extent-tree.c: In function '__btrfs_free_extent':
fs/btrfs/extent-tree.c:3187:4: warning: format '%lu' expects argument of type 'long unsigned int', but argument 8 has type 'unsigned int' [-Wformat=]
Fixes: 1c2a07f598d5 ("btrfs: extent-tree: kill BUG_ON() in __btrfs_free_extent()") Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Pujin Shi <shipujin.t@gmail.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
(backported from commit cad69d139651423b9cb8917f514740ed3f08b10a) Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Colin Ian King <colin.king@canonical.com> Acked-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Niklas Schnelle [Thu, 12 Nov 2020 09:44:29 +0000 (10:44 +0100)]
s390/pci: fix hot-plug of PCI function missing bus
BugLink: https://bugs.launchpad.net/bugs/1903682
Under some circumstances in particular with "Reconfigure I/O Path"
a zPCI function may first appear in Standby through a PCI event with
PEC 0x0302 which initially makes it visible to the zPCI subsystem,
Only after that is it configured with a zPCI event with PEC 0x0301.
If the zbus is still missing a PCI function zero (devfn == 0) when the
PCI event 0x0301 is handled zdev->zbus->bus is still NULL and gets
dereferenced in common code.
Check for this case and enable but don't scan the zPCI function.
This matches what would happen if we immediately got the 0x0301
configuration request or the function was included in CLP List PCI.
In all cases the PCI functions with devfn != 0 will be scanned once
function 0 appears.
Fixes: 3047766bc6ec ("s390/pci: fix enabling a reserved PCI function") Cc: <stable@vger.kernel.org> # 5.8 Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com> Acked-by: Pierre Morel <pmorel@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
(cherry picked from commit 0b2ca2c7d0c9e2731d01b6c862375d44a7e13923) Signed-off-by: Frank Heimes <frank.heimes@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>