The struct is passed between skb_find_text and its callbacks
skb_prepare_seq_read, skb_seq_read and skb_abort_seq read through
the textsearch interface using TS_SKB_CB.
I assumed that this mapped to skb->cb like other .._SKB_CB wrappers.
skb->cb is 48B. But it maps to ts_state->cb, which is only 40B.
skb->cb was increased from 40B to 48B after ts_state was introduced,
in commit 3e3850e989c5 ("[NETFILTER]: Fix xfrm lookup in
ip_route_me_harder/ip6_route_me_harder").
Increase ts_state.cb[] to 48 to fit the struct.
Also add a BUILD_BUG_ON to avoid a repeat.
The alternative is to directly add a dependency from textsearch onto
linux/skbuff.h, but I think the intent is textsearch to have no such
dependencies on its callers.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=211911 Fixes: 97550f6fa592 ("net: compound page support in skb_seq_read") Reported-by: Kris Karas <bugs-a17@moonlit-rail.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
We bypass IOPOLL completion polling (and reaping) for the SQPOLL thread,
but if it's the thread itself invoking cancelations, then we still need
to perform it or no one will.
52-bit VA kernels can run on hardware that is only 48-bit capable, but
configure the ID map as 52-bit by default. This was not a problem until
recently, because the special T0SZ value for a 52-bit VA space was never
programmed into the TCR register anwyay, and because a 52-bit ID map
happens to use the same number of translation levels as a 48-bit one.
This behavior was changed by commit 1401bef703a4 ("arm64: mm: Always update
TCR_EL1 from __cpu_set_tcr_t0sz()"), which causes the unsupported T0SZ
value for a 52-bit VA to be programmed into TCR_EL1. While some hardware
simply ignores this, Mark reports that Amberwing systems choke on this,
resulting in a broken boot. But even before that commit, the unsupported
idmap_t0sz value was exposed to KVM and used to program TCR_EL2 incorrectly
as well.
Given that we already have to deal with address spaces being either 48-bit
or 52-bit in size, the cleanest approach seems to be to simply default to
a 48-bit VA ID map, and only switch to a 52-bit one if the placement of the
kernel in DRAM requires it. This is guaranteed not to happen unless the
system is actually 52-bit VA capable.
Commit b0841eefd969 ("configfs: provide exclusion between IO and removals")
uses ->frag_dead to mark the fragment state, thus no bothering with extra
refcount on config_item when opening a file. The configfs_get_config_item
was removed in __configfs_open_file, but not with config_item_put. So the
refcount on config_item will lost its balance, causing use-after-free
issues in some occasions like this:
2. Then run:
for file in /config
do
echo $file
grep -R 'key' $file
done
3. __configfs_open_file will be called in parallel, the first one
got called will do:
if (file->f_mode & FMODE_READ) {
if (!(inode->i_mode & S_IRUGO))
goto out_put_module;
config_item_put(buffer->item);
kref_put()
package_details_release()
kfree()
the other one will run into use-after-free issues like this:
BUG: KASAN: use-after-free in __configfs_open_file+0x1bc/0x3b0
Read of size 8 at addr fffffff155f02480 by task grep/13096
CPU: 0 PID: 13096 Comm: grep VIP: 00 Tainted: G W 4.14.116-kasan #1
TGID: 13096 Comm: grep
Call trace:
dump_stack+0x118/0x160
kasan_report+0x22c/0x294
__asan_load8+0x80/0x88
__configfs_open_file+0x1bc/0x3b0
configfs_open_file+0x28/0x34
do_dentry_open+0x2cc/0x5c0
vfs_open+0x80/0xe0
path_openat+0xd8c/0x2988
do_filp_open+0x1c4/0x2fc
do_sys_open+0x23c/0x404
SyS_openat+0x38/0x48
Recent patch to prevent calling __nvme_fc_abort_outstanding_ios in
interrupt context results in a possible race condition. A controller
reset results in errored io completions, which schedules error
work. The change of error work to a work element allows it to fire
after the ctrl state transition to NVME_CTRL_CONNECTING, causing
any outstanding io (used to initialize the controller) to fail and
cause problems for connect_work.
Add a state check to only schedule error work if not in the RESETTING
state.
Fixes: 19fce0470f05 ("nvme-fc: avoid calling _nvme_fc_abort_outstanding_ios from interrupt context") Signed-off-by: Nigel Kirkland <nkirkland2304@gmail.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Freed pages are not subtracted from the allocated_pages counter in
ttm_pool_type_fini(), causing a leak in the count on device removal.
The next shrinker invocation loops forever trying to free pages that are
no longer in the pool:
Using ttm_pool_type_take() to remove pages from the pool before freeing
them correctly accounts for the freed pages.
Fixes: d099fc8f540a ("drm/ttm: new TT backend allocation pool v3") Signed-off-by: Anthony DeRossi <ajderossi@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210303011723.22512-1-ajderossi@gmail.com Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
An xattr 'get' handler is expected to return the length of the value on
success, yet _nfs4_get_security_label() (and consequently also
nfs4_xattr_get_nfs4_label(), which is used as an xattr handler) returns
just 0 on success.
Fix this by returning label.len instead, which contains the length of
the result.
Fixes: aa9c2669626c ("NFS: Client implementation of Labeled-NFS") Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com> Reviewed-by: James Morris <jamorris@linux.microsoft.com> Reviewed-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
There should be no reason to expect the directory permissions to change
just because the directory contents changed or a negative lookup timed
out. So let's avoid doing a full call to nfs_mark_for_revalidate() in
that case.
Furthermore, if this is a negative dentry, and we haven't actually done
a new lookup, then we have no reason yet to believe the directory has
changed at all. So let's remove the gratuitous directory inode
invalidation altogether when called from
nfs_lookup_revalidate_negative().
We could recurse into NFS doing memory reclaim while sending a sync task,
which might result in a deadlock. Set memalloc_nofs_save for sync task
execution.
Fixes: a1231fda7e94 ("SUNRPC: Set memalloc_nofs_save() on all rpciod/xprtiod jobs") Signed-off-by: Benjamin Coddington <bcodding@redhat.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
pfn_valid() validates a pfn but basically it checks for a valid struct page
backing for that pfn. It should always return positive for memory ranges
backed with struct page mapping. But currently pfn_valid() fails for all
ZONE_DEVICE based memory types even though they have struct page mapping.
pfn_valid() asserts that there is a memblock entry for a given pfn without
MEMBLOCK_NOMAP flag being set. The problem with ZONE_DEVICE based memory is
that they do not have memblock entries. Hence memblock_is_map_memory() will
invariably fail via memblock_search() for a ZONE_DEVICE based address. This
eventually fails pfn_valid() which is wrong. memblock_is_map_memory() needs
to be skipped for such memory ranges. As ZONE_DEVICE memory gets hotplugged
into the system via memremap_pages() called from a driver, their respective
memory sections will not have SECTION_IS_EARLY set.
Normal hotplug memory will never have MEMBLOCK_NOMAP set in their memblock
regions. Because the flag MEMBLOCK_NOMAP was specifically designed and set
for firmware reserved memory regions. memblock_is_map_memory() can just be
skipped as its always going to be positive and that will be an optimization
for the normal hotplug memory. Like ZONE_DEVICE based memory, all normal
hotplugged memory too will not have SECTION_IS_EARLY set for their sections
Skipping memblock_is_map_memory() for all non early memory sections would
fix pfn_valid() problem for ZONE_DEVICE based memory and also improve its
performance for normal hotplug memory as well.
In case of error, the function ioremap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
There is no usrio config defined for default gem config leading to
a kernel panic devices that don't define a data. This issue can be
reprdouced with microchip polar fire soc where compatible string
is defined as "cdns,macb".
Fixes: edac63861db7 ("add userio bits as platform configuration") Signed-off-by: Atish Patra <atish.patra@wdc.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Commit af99da74333b ("powerpc/sstep: Support VSX vector paired storage
access instructions") added loading and storing 32 word long data into
adjacent VSRs. However the calculation used to determine if two VSRs
needed to be loaded/stored inadvertently prevented the load/storing
taking place for instructions with a data length less than 16 words.
This causes the emulation to not function correctly, which can be seen
by the alignment_handler selftest:
According to the RZ/A1H Group, RZ/A1M Group User's Manual: Hardware,
Rev. 4.00, the TRSCER register has bit 9 reserved, hence we can't use
the driver's default TRSCER mask. Add the explicit initializer for
sh_eth_cpu_data::trscer_err_mask for R7S72100.
Fixes: db893473d313 ("sh_eth: Add support for r7s72100") Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The previous implementation of .handle_interrupt() did not take into
account the fact that all the interrupt status registers should be
acknowledged since multiple interrupt sources could be asserted.
Fix this by reading all the status registers before exiting with
IRQ_NONE or triggering the PHY state machine.
Routes are currently processed from a workqueue whereas nexthop objects
are processed in system call context. This can result in the driver not
finding a suitable nexthop group for a route and issuing a warning [1].
Fix this by ignoring such routes earlier in the process. The subsequent
deletion notification will be ignored as well.
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the call to
`comedi_buf_write_samples()` is passing the address of a 32-bit integer
parameter. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the parameter
holding the sample value to `unsigned short`.
[Note: the bug was introduced in commit edf4537bcbf5 ("staging: comedi:
pcl818: use comedi_buf_write_samples()") but the patch applies better to
commit d615416de615 ("staging: comedi: pcl818: introduce
pcl818_ai_write_sample()").]
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the call to
`comedi_buf_write_samples()` is passing the address of a 32-bit integer
variable. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the variable
holding the sample value to `unsigned short`.
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the calls to
`comedi_buf_write_samples()` are passing the address of a 32-bit integer
variable. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the variable
holding the sample value to `unsigned short`.
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the call to
`comedi_buf_write_samples()` is passing the address of a 32-bit integer
variable. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the variable
holding the sample value to `unsigned short`.
[Note: the bug was introduced in commit 1700529b24cc ("staging: comedi:
dmm32at: use comedi_buf_write_samples()") but the patch applies better
to the later (but in the same kernel release) commit 0c0eadadcbe6e
("staging: comedi: dmm32at: introduce dmm32_ai_get_sample()").]
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the call to
`comedi_buf_write_samples()` is passing the address of a 32-bit integer
variable. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the variable
holding the sample value to `unsigned short`.
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the call to
`comedi_buf_write_samples()` is passing the address of a 32-bit integer
variable. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the variable
holding the sample value to `unsigned short`.
Fixes: d1d24cb65ee3 ("staging: comedi: das6402: read analog input samples in interrupt handler") Cc: <stable@vger.kernel.org> # 3.19+ Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Link: https://lore.kernel.org/r/20210223143055.257402-5-abbotti@mev.co.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the calls to
`comedi_buf_write_samples()` are passing the address of a 32-bit integer
variable. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the variables
holding the sample value to `unsigned short`. The type of the `val`
parameter of `pci1710_ai_read_sample()` is changed to `unsigned short *`
accordingly. The type of the `val` variable in `pci1710_ai_insn_read()`
is also changed to `unsigned short` since its address is passed to
`pci1710_ai_read_sample()`.
The digital input subdevice supports Comedi asynchronous commands that
read interrupt status information. This uses 16-bit Comedi samples (of
which only the bottom 8 bits contain status information). However, the
interrupt handler is calling `comedi_buf_write_samples()` with the
address of a 32-bit variable `unsigned int status`. On a bigendian
machine, this will copy 2 bytes from the wrong end of the variable. Fix
it by changing the type of the variable to `unsigned short`.
Fixes: a8c66b684efa ("staging: comedi: addi_apci_1500: rewrite the subdevice support functions") Cc: <stable@vger.kernel.org> #4.0+ Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Link: https://lore.kernel.org/r/20210223143055.257402-3-abbotti@mev.co.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The Change-Of-State (COS) subdevice supports Comedi asynchronous
commands to read 16-bit change-of-state values. However, the interrupt
handler is calling `comedi_buf_write_samples()` with the address of a
32-bit integer `&s->state`. On bigendian architectures, it will copy 2
bytes from the wrong end of the 32-bit integer. Fix it by transferring
the value via a 16-bit integer.
Function _rtl92e_wx_set_scan calls memcpy without checking the length.
A user could control that length and trigger a buffer overflow.
Fix by checking the length is within the maximum allowed size.
Function r8712_sitesurvey_cmd calls memcpy without checking the length.
A user could control that length and trigger a buffer overflow.
Fix by checking the length is within the maximum allowed size.
The "ie_len" is a value in the 1-255 range that comes from the user. We
have to cap it to ensure that it's not too large or it could lead to
memory corruption.
Fixes: 9a7fe54ddc3a ("staging: r8188eu: Add source files for new driver - part 1") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/YEHyQCrFZKTXyT7J@mwanda Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The memdup_user() function does not necessarily return a NUL terminated
string so this can lead to a read overflow. Switch from memdup_user()
to strndup_user() to fix this bug.
Verify that user applications are not using the kernel RPC message
handle to restrict them from directly attaching to guest OS on the
remote subsystem. This is a port of CVE-2019-2308 fix.
Fixes: c68cfb718c8f ("misc: fastrpc: Add support for context Invoke method") Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Cc: Jonathan Marek <jonathan@marek.ca> Cc: stable@vger.kernel.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20210212192658.3476137-1-dmitry.baryshkov@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Export the module FDT device table to ensure the FDT compatible strings
are listed in the module alias. This help the pvpanic driver can be
loaded on boot automatically not only the ACPI device, but also the FDT
device.
Fixes: 46f934c9a12fc ("misc/pvpanic: add support to get pvpanic device info FDT") Signed-off-by: Shile Zhang <shile.zhang@linux.alibaba.com> Link: https://lore.kernel.org/r/20210218123116.207751-1-shile.zhang@linux.alibaba.com Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
FIFO is triggered 4 intervals after receiving a byte, it's good
when we don't care about the time of reception, but are only
interested in the presence of any activity on the line.
Unfortunately, this method is not suitable for all tasks,
for example, the RS-485 protocol will not work properly,
since the state machine must track the request-response time
and after the timeout expires, a decision is made that the device
on the line is not responding.
usbip_sockfd_store() is invoked when user requests attach (import)
detach (unimport) usb gadget device from usbip host. vhci_hcd sends
import request and usbip_sockfd_store() exports the device if it is
free for export.
Export and unexport are governed by local state and shared state
- Shared state (usbip device status, sockfd) - sockfd and Device
status are used to determine if stub should be brought up or shut
down. Device status is shared between host and client.
- Local state (tcp_socket, rx and tx thread task_struct ptrs)
A valid tcp_socket controls rx and tx thread operations while the
device is in exported state.
- While the device is exported, device status is marked used and socket,
sockfd, and thread pointers are valid.
Export sequence (stub-up) includes validating the socket and creating
receive (rx) and transmit (tx) threads to talk to the client to provide
access to the exported device. rx and tx threads depends on local and
shared state to be correct and in sync.
Unexport (stub-down) sequence shuts the socket down and stops the rx and
tx threads. Stub-down sequence relies on local and shared states to be
in sync.
There are races in updating the local and shared status in the current
stub-up sequence resulting in crashes. These stem from starting rx and
tx threads before local and global state is updated correctly to be in
sync.
1. Doesn't handle kthread_create() error and saves invalid ptr in local
state that drives rx and tx threads.
2. Updates tcp_socket and sockfd, starts stub_rx and stub_tx threads
before updating usbip_device status to SDEV_ST_USED. This opens up a
race condition between the threads and usbip_sockfd_store() stub up
and down handling.
Fix the above problems:
- Stop using kthread_get_run() macro to create/start threads.
- Create threads and get task struct reference.
- Add kthread_create() failure handling and bail out.
- Hold usbip_device lock to update local and shared states after
creating rx and tx threads.
- Update usbip_device status to SDEV_ST_USED.
- Update usbip_device tcp_socket, sockfd, tcp_rx, and tcp_tx
- Start threads after usbip_device (tcp_socket, sockfd, tcp_rx, tcp_tx,
and status) is complete.
Credit goes to syzbot and Tetsuo Handa for finding and root-causing the
kthread_get_run() improper error handling problem and others. This is a
hard problem to find and debug since the races aren't seen in a normal
case. Fuzzing forces the race window to be small enough for the
kthread_get_run() error path bug and starting threads before updating the
local and shared state bug in the stub-up sequence.
attach_store() is invoked when user requests import (attach) a device
from usbip host.
Attach and detach are governed by local state and shared state
- Shared state (usbip device status) - Device status is used to manage
the attach and detach operations on import-able devices.
- Local state (tcp_socket, rx and tx thread task_struct ptrs)
A valid tcp_socket controls rx and tx thread operations while the
device is in exported state.
- Device has to be in the right state to be attached and detached.
Attach sequence includes validating the socket and creating receive (rx)
and transmit (tx) threads to talk to the host to get access to the
imported device. rx and tx threads depends on local and shared state to
be correct and in sync.
Detach sequence shuts the socket down and stops the rx and tx threads.
Detach sequence relies on local and shared states to be in sync.
There are races in updating the local and shared status in the current
attach sequence resulting in crashes. These stem from starting rx and
tx threads before local and global state is updated correctly to be in
sync.
1. Doesn't handle kthread_create() error and saves invalid ptr in local
state that drives rx and tx threads.
2. Updates tcp_socket and sockfd, starts stub_rx and stub_tx threads
before updating usbip_device status to VDEV_ST_NOTASSIGNED. This opens
up a race condition between the threads, port connect, and detach
handling.
Fix the above problems:
- Stop using kthread_get_run() macro to create/start threads.
- Create threads and get task struct reference.
- Add kthread_create() failure handling and bail out.
- Hold vhci and usbip_device locks to update local and shared states after
creating rx and tx threads.
- Update usbip_device status to VDEV_ST_NOTASSIGNED.
- Update usbip_device tcp_socket, sockfd, tcp_rx, and tcp_tx
- Start threads after usbip_device (tcp_socket, sockfd, tcp_rx, tcp_tx,
and status) is complete.
Credit goes to syzbot and Tetsuo Handa for finding and root-causing the
kthread_get_run() improper error handling problem and others. This is
hard problem to find and debug since the races aren't seen in a normal
case. Fuzzing forces the race window to be small enough for the
kthread_get_run() error path bug and starting threads before updating the
local and shared state bug in the attach sequence.
- Update usbip_device tcp_rx and tcp_tx pointers holding vhci and
usbip_device locks.
Tested with syzbot reproducer:
- https://syzkaller.appspot.com/text?tag=ReproC&x=14801034d00000
usbip_sockfd_store() is invoked when user requests attach (import)
detach (unimport) usb device from usbip host. vhci_hcd sends import
request and usbip_sockfd_store() exports the device if it is free
for export.
Export and unexport are governed by local state and shared state
- Shared state (usbip device status, sockfd) - sockfd and Device
status are used to determine if stub should be brought up or shut
down.
- Local state (tcp_socket, rx and tx thread task_struct ptrs)
A valid tcp_socket controls rx and tx thread operations while the
device is in exported state.
- While the device is exported, device status is marked used and socket,
sockfd, and thread pointers are valid.
Export sequence (stub-up) includes validating the socket and creating
receive (rx) and transmit (tx) threads to talk to the client to provide
access to the exported device. rx and tx threads depends on local and
shared state to be correct and in sync.
Unexport (stub-down) sequence shuts the socket down and stops the rx and
tx threads. Stub-down sequence relies on local and shared states to be
in sync.
There are races in updating the local and shared status in the current
stub-up sequence resulting in crashes. These stem from starting rx and
tx threads before local and global state is updated correctly to be in
sync.
1. Doesn't handle kthread_create() error and saves invalid ptr in local
state that drives rx and tx threads.
2. Updates tcp_socket and sockfd, starts stub_rx and stub_tx threads
before updating usbip_device status to SDEV_ST_USED. This opens up a
race condition between the threads and usbip_sockfd_store() stub up
and down handling.
Fix the above problems:
- Stop using kthread_get_run() macro to create/start threads.
- Create threads and get task struct reference.
- Add kthread_create() failure handling and bail out.
- Hold usbip_device lock to update local and shared states after
creating rx and tx threads.
- Update usbip_device status to SDEV_ST_USED.
- Update usbip_device tcp_socket, sockfd, tcp_rx, and tcp_tx
- Start threads after usbip_device (tcp_socket, sockfd, tcp_rx, tcp_tx,
and status) is complete.
Credit goes to syzbot and Tetsuo Handa for finding and root-causing the
kthread_get_run() improper error handling problem and others. This is a
hard problem to find and debug since the races aren't seen in a normal
case. Fuzzing forces the race window to be small enough for the
kthread_get_run() error path bug and starting threads before updating the
local and shared state bug in the stub-up sequence.
Tested with syzbot reproducer:
- https://syzkaller.appspot.com/text?tag=ReproC&x=14801034d00000
Fix usbip_sockfd_store() to validate the passed in file descriptor is
a stream socket. If the file descriptor passed was a SOCK_DGRAM socket,
sock_recvmsg() can't detect end of stream.
Fix attach_store() to validate the passed in file descriptor is a
stream socket. If the file descriptor passed was a SOCK_DGRAM socket,
sock_recvmsg() can't detect end of stream.
Fix usbip_sockfd_store() to validate the passed in file descriptor is
a stream socket. If the file descriptor passed was a SOCK_DGRAM socket,
sock_recvmsg() can't detect end of stream.
Add PID for CH340 that's found on cheap programmers.
The driver works flawlessly as soon as the new PID (0x9986) is added to it.
These look like ANU232MI but ship with a ch341 inside. They have no special
identifiers (mine only has the string "DB9D20130716" printed on the PCB and
nothing identifiable on the packaging. The merchant i bought it from
doesn't sell these anymore).
the lsusb -v output is:
Bus 001 Device 009: ID 9986:7523
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x9986
idProduct 0x7523
bcdDevice 2.54
iManufacturer 0
iProduct 0
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0027
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 96mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 1
bInterfaceProtocol 2
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 1
I've confirmed that both the ASMedia ASM1042A and ASM3242 have the same
problem as the ASM1142 and ASM2142/ASM3142, where they lose some of the
upper bits of 64-bit DMA addresses. As with the other chips, this can
cause problems on systems where the upper bits matter, and adding the
XHCI_NO_64BIT_SUPPORT quirk completely fixes the issue.
A xHC USB 3 port might miss the first wake signal from a USB 3 device
if the port LFPS reveiver isn't enabled fast enough after xHC resume.
xHC host will anyway be resumed by a PME# signal, but will go back to
suspend if no port activity is seen.
The device resends the U3 LFPS wake signal after a 100ms delay, but
by then host is already suspended, starting all over from the
beginning of this issue.
USB 3 specs say U3 wake LFPS signal is sent for max 10ms, then device
needs to delay 100ms before resending the wake.
Don't suspend immediately if port activity isn't detected in resume.
Instead add a retry. If there is no port activity then delay for 120ms,
and re-check for port activity.
On some systems rt2800usb and mt7601u devices are unable to operate since
commit f8f80be501aa ("xhci: Use soft retry to recover faster from
transaction errors")
Seems that some xHCI controllers can not perform Soft Retry correctly,
affecting those devices.
To avoid the problem add xhci->quirks flag that restore pre soft retry
xhci behaviour for affected xHCI controllers. Currently those are
AMD_PROMONTORYA_4 and AMD_PROMONTORYA_2, since it was confirmed
by the users: on those xHCI hosts issue happen and is gone after
disabling Soft Retry.
[minor commit message rewording for checkpatch -Mathias]
Fixes: f8f80be501aa ("xhci: Use soft retry to recover faster from transaction errors") Cc: <stable@vger.kernel.org> # 4.20+ Reported-by: Bernhard <bernhard.gebetsberger@gmx.at> Tested-by: Bernhard <bernhard.gebetsberger@gmx.at> Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202541 Link: https://lore.kernel.org/r/20210311115353.2137560-2-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
According to the datasheet, this controller has a restriction
which "set an endpoint number so that combinations of the DIR bit and
the EPNUM bits do not overlap.". However, since the udc core driver is
possible to assign a bulk pipe as an interrupt endpoint, an endpoint
number may not match the pipe number. After that, when user rebinds
another gadget driver, this driver broke the restriction because
the driver didn't clear any configuration in usb_ep_disable().
Example:
# modprobe g_ncm
Then, EP3 = pipe 3, EP4 = pipe 4, EP5 = pipe 6
# rmmod g_ncm
# modprobe g_hid
Then, EP3 = pipe 6, EP4 = pipe 7.
So, pipe 3 and pipe 6 are set as EP3.
Apparently an application that opens a device and calls select()
on it, will hang if the decice is disconnected. It's a little
surprising that we had this bug for 15 years, but apparently
nobody ever uses select() with a printer: only write() and read(),
and those work fine. Well, you can also select() with a timeout.
The fix is modeled after devio.c. A few other drivers check the
condition first, then do not add the wait queue in case the
device is disconnected. We doubt that's completely race-free.
So, this patch adds the process first, then locks properly
and checks for the disconnect.
The dwc3-qcom currently enables wakeup interrupts unconditionally
when suspending, however this should not be done when wakeup is
disabled (e.g. through the sysfs attribute power/wakeup). Only
enable wakeup interrupts when device_may_wakeup() returns true.
It enables USB Host support for sc8180x ACPI boot, both the standalone
one and the one behind URS (USB Role Switch). And they share the
the same dwc3_acpi_pdata with sdm845.
For sdm845 ACPI boot, the URS (USB Role Switch) node in ACPI DSDT table
holds the memory resource, while interrupt resources reside in the child
nodes USB0 and UFN0. It adds USB0 host support by probing URS node,
creating platform device for USB0 node, and then retrieve interrupt
resources from USB0 platform device.
of_get_child_by_name() increments the reference counter of the OF node it
managed to find. So after the code is done using the device node, the
refcount must be decremented. Add missing of_node_put() invocation then
to the dwc3_qcom_of_register_core() method, since DWC3 OF node is being
used only there.
As per UAC2 Audio Data Formats spec (2.3.1.1 USB Packets),
if the sampling rate is a constant, the allowable variation
of number of audio slots per virtual frame is +/- 1 audio slot.
It means that endpoint should be able to accept/send +1 audio
slot.
Previous endpoint max_packet_size calculation code
was adding sometimes +1 audio slot due to DIV_ROUND_UP
behaviour which was rounding up to closest integer.
However this doesn't work if the numbers are divisible.
It had no any impact with Linux hosts which ignore
this issue, but in case of more strict Windows it
caused rejected enumeration
Thus always add +1 audio slot to endpoint's max packet size
Fixes: 913e4a90b6f9 ("usb: gadget: f_uac2: finalize wMaxPacketSize according to bandwidth") Cc: Peter Chen <peter.chen@freescale.com> Cc: <stable@vger.kernel.org> #v4.3+ Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com> Link: https://lore.kernel.org/r/1614599375-8803-2-git-send-email-ruslan.bilovol@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
In case of error, the function devm_platform_ioremap_resource()
returns ERR_PTR() and never returns NULL. The NULL test in the
return value check should be replaced with IS_ERR().
The CDC ACM driver is false matching the Goodix Fingerprint device
against the USB_CDC_ACM_PROTO_AT_V25TER.
The Goodix Fingerprint device is a biometrics sensor that should be
handled in user-space. libfprint has some support for Goodix
fingerprint sensors, although not for this particular one. It is
possible that the vendor allocates a PID per OEM (Lenovo, Dell etc).
If this happens to be the case then more devices from the same vendor
could potentially match the ACM modem module table.
In case of interrupted syscalls, prevent sending CLOSE commands for
compound CREATE+CLOSE requests by introducing an
CIFS_CP_CREATE_CLOSE_OP flag to indicate lower layers that it should
not send a CLOSE command to the MIDs corresponding the compound
CREATE+CLOSE request.
A simple reproducer:
#!/bin/bash
mount //server/share /mnt -o username=foo,password=***
tc qdisc add dev eth0 root netem delay 450ms
stat -f /mnt &>/dev/null & pid=$!
sleep 0.01
kill $pid
tc qdisc del dev eth0 root
umount /mnt
The problem occurs when cqhci_request() get called after cqhci_disable() as
it leads to access of allocated memory that has already been freed. Let's
fix the problem by calling cqhci_disable() a bit later in the remove path.
Signed-off-by: Frank Li <Frank.Li@nxp.com> Diagnosed-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20210303174248.542175-1-Frank.Li@nxp.com Fixes: f690f4409ddd ("mmc: mmc: Enable CQE's") Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
An issue has been observed on STM32MP157C-EV1 board, with an erase command
with secure erase argument, ending up waiting for ~4 hours before timeout.
The requested busy timeout from the mmc core ends up with 14784000ms (~4
hours), but the supported host->max_busy_timeout is 86767ms, which leads to
that the core switch to use an R1 response in favor of the R1B and polls
for busy with the host->card_busy() ops. In this case the polling doesn't
work as expected, as we never detects that the card stops signaling busy,
which leads to the following message:
mmc1: Card stuck being busy! __mmc_poll_for_busy
The problem boils done to that the stm32 variants can't use R1 responses in
favor of R1B responses, as it leads to an internal state machine in the
controller to get stuck. To continue to process requests, it would need to
be reset.
To fix this problem, let's set MMC_CAP_NEED_RSP_BUSY for the stm32 variant,
which prevent the mmc core from switching to R1 responses. Additionally,
let's cap the cmd->busy_timeout to the host->max_busy_timeout, thus rely on
86767ms to be sufficient (~66 seconds was need for this test case).
Fixes: 94fe2580a2f3 ("mmc: core: Enable erase/discard/trim support for all mmc hosts") Signed-off-by: Yann Gautier <yann.gautier@foss.st.com> Link: https://lore.kernel.org/r/20210225145454.12780-1-yann.gautier@foss.st.com Cc: stable@vger.kernel.org
[Ulf: Simplified the code and extended the commit message] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
When changing the cpu affinity of an event it can happen today that
(with some unlucky timing) the same event will be handled on the old
and the new cpu at the same time.
Avoid that by adding an "event active" flag to the per-event data and
call the handler only if this flag isn't set.
An event channel should be kept masked when an eoi is pending for it.
When being migrated to another cpu it might be unmasked, though.
In order to avoid this keep three different flags for each event channel
to be able to distinguish "normal" masking/unmasking from eoi related
masking/unmasking and temporary masking. The event channel should only
be able to generate an interrupt if all flags are cleared.
Cc: stable@vger.kernel.org Fixes: 54c9de89895e ("xen/events: add a new "late EOI" evtchn framework") Reported-by: Julien Grall <julien@xen.org> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Julien Grall <jgrall@amazon.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Tested-by: Ross Lagerwall <ross.lagerwall@citrix.com> Link: https://lore.kernel.org/r/20210306161833.4552-3-jgross@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[boris -- corrected Fixed tag format]
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
When creating a new event channel with 2-level events the affinity
needs to be reset initially in order to avoid using an old affinity
from earlier usage of the event channel port. So when tearing an event
channel down reset all affinity bits.
The same applies to the affinity when onlining a vcpu: all old
affinity settings for this vcpu must be reset. As percpu events get
initialized before the percpu event channel hook is called,
resetting of the affinities happens after offlining a vcpu (this is
working, as initial percpu memory is zeroed out).
Prevent that an IO request is build during device shutdown initiated by
a driver unbind. This request will never be able to be processed or
canceled and will hang forever. This will lead also to a hanging unbind.
Fix by checking not only if the device is in READY state but also check
that there is no device offline initiated before building a new IO request.
In case of an unbind of the DASD device driver the function
dasd_generic_remove() is called which shuts down the device.
Among others this functions removes the int_handler from the cdev.
During shutdown the device cancels all outstanding IO requests and waits
for completion of the clear request.
Unfortunately the clear interrupt will never be received when there is no
interrupt handler connected.
Fix by moving the int_handler removal after the call to the state machine
where no request or interrupt is outstanding.
Cc: stable@vger.kernel.org Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Tested-by: Bjoern Walk <bwalk@linux.ibm.com> Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Commit 0fdf1bb75953 ("arm64: perf: Avoid PMXEV* indirection") changed
armv8pmu_read_evcntr() to return a u32 instead of u64. The result is
silent truncation of the event counter when using 64-bit counters. Given
the offending commit appears to have passed thru several folks, it seems
likely this was a bad rebase after v8.5 PMU 64-bit counters landed.
Cc: Alexandru Elisei <alexandru.elisei@arm.com> Cc: Julien Thierry <julien.thierry.kdev@gmail.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will@kernel.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: <stable@vger.kernel.org> Fixes: 0fdf1bb75953 ("arm64: perf: Avoid PMXEV* indirection") Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Mark Rutland <mark.rutland@arm.com> Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com> Link: https://lore.kernel.org/r/20210310004412.1450128-1-robh@kernel.org Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
In a system supporting MTE, the linear map must allow reading/writing
allocation tags by setting the memory type as Normal Tagged. Currently,
this is only handled for memory present at boot. Hotplugged memory uses
Normal non-Tagged memory.
Introduce pgprot_mhp() for hotplugged memory and use it in
add_memory_resource(). The arm64 code maps pgprot_mhp() to
pgprot_tagged().
Note that ZONE_DEVICE memory should not be mapped as Tagged and
therefore setting the memory type in arch_add_memory() is not feasible.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Fixes: 0178dc761368 ("arm64: mte: Use Normal Tagged attributes for the linear map") Reported-by: Patrick Daly <pdaly@codeaurora.org> Tested-by: Patrick Daly <pdaly@codeaurora.org> Link: https://lore.kernel.org/r/1614745263-27827-1-git-send-email-pdaly@codeaurora.org Cc: <stable@vger.kernel.org> # 5.10.x Cc: Will Deacon <will@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: David Hildenbrand <david@redhat.com> Reviewed-by: David Hildenbrand <david@redhat.com> Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Link: https://lore.kernel.org/r/20210309122601.5543-1-catalin.marinas@arm.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
When CONFIG_DEBUG_VIRTUAL is enabled, the default page_to_virt() macro
implementation from include/linux/mm.h is used. That definition doesn't
account for KASAN tags, which leads to no tags on page_alloc allocations.
Provide an arm64-specific definition for page_to_virt() when
CONFIG_DEBUG_VIRTUAL is enabled that takes care of KASAN tags.
Fixes: 2813b9c02962 ("kasan, mm, arm64: tag non slab memory allocated via pagealloc") Cc: <stable@vger.kernel.org> Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Link: https://lore.kernel.org/r/4b55b35202706223d3118230701c6a59749d9b72.1615219501.git.andreyknvl@google.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Commit 384d87ef2c95 ("block: Do not discard buffers under a mounted
filesystem") made paths issuing discard or zeroout requests to the
underlying device try to grab block device in exclusive mode. If that
failed we returned EBUSY to userspace. This however caused unexpected
fallout in userspace where e.g. FUSE filesystems issue discard requests
from userspace daemons although the device is open exclusively by the
kernel. Also shrinking of logical volume by LVM issues discard requests
to a device which may be claimed exclusively because there's another LV
on the same PV. So to avoid these userspace regressions, fall back to
invalidate_inode_pages2_range() instead of returning EBUSY to userspace
and return EBUSY only of that call fails as well (meaning that there's
indeed someone using the particular device range we are trying to
discard).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=211167 Fixes: 384d87ef2c95 ("block: Do not discard buffers under a mounted filesystem") CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
When zone reset ioctl and data read race for a same zone on zoned block
devices, the data read leaves stale page cache even though the zone
reset ioctl zero clears all the zone data on the device. To avoid
non-zero data read from the stale page cache after zone reset, discard
page cache of reset target zones in blkdev_zone_mgmt_ioctl(). Introduce
the helper function blkdev_truncate_zone_range() to discard the page
cache. Ensure the page cache discarded by calling the helper function
before and after zone reset in same manner as fallocate does.
This patch can be applied back to the stable kernel version v5.10.y.
Rework is needed for older stable kernels.
It turns out that there are in fact userspace implementations that
care and this recent change caused a regression.
https://github.com/containers/buildah/issues/3071
As the motivation for the original change was future development,
and the impact is existing real world code just revert this change
and allow the ambiguity in v3 file caps.
We are required to call dev_pm_opp_put() from outside of the
opp_table->lock as debugfs removal needs to happen lock-less to avoid
circular dependency issues.
commit cf1fac943c63 ("opp: Reduce the size of critical section in
_opp_kref_release()") tried to fix that introducing a new routine
_opp_get_next() which keeps returning OPPs that can be freed by the
callers and this routine shall be called without holding the
opp_table->lock.
Though the commit overlooked the fact that the OPPs can be referenced by
other users as well and this routine will end up dropping references
which were taken by other users and hence freeing the OPPs prematurely.
In effect, other users of the OPPs will end up having invalid pointers
at hand. We didn't see any crash reports earlier as the exact situation
never happened, though it is certainly possible.
We need a way to mark which OPPs are no longer referenced by the OPP
core, so we don't drop extra references to them accidentally.
This commit adds another OPP flag, "removed", which is used to track
this. And now we should never end up dropping extra references to the
OPPs.
Cc: v5.11+ <stable@vger.kernel.org> # v5.11+ Fixes: cf1fac943c63 ("opp: Reduce the size of critical section in _opp_kref_release()") Signed-off-by: Beata Michalska <beata.michalska@arm.com>
[ Viresh: Almost rewrote entire patch, added new "removed" field,
rewrote commit log and added the correct Fixes tag. ] Co-developed-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Other Plantronics headset models seem requiring the same workaround as
C320-M to add the 20ms delay for the control messages, too. Apply the
workaround generically for devices with the vendor ID 0x047f.
Note that the problem didn't surface before 5.11 just with luck.
Since 5.11 got a big code rewrite about the stream handling, the
parameter setup procedure has changed, and this seemed triggering the
problem more often.
Dell AE515 sound bar (413c:a506) spews the error messages when the
driver tries to read the current sample frequency, hence it needs to
be on the list in snd_usb_get_sample_rate_quirk().
When HD-audio bus receives unsolicited events during its system
suspend/resume (S3 and S4) phase, the controller driver may still try
to process events although the codec chips are already (or yet)
powered down. This might screw up the codec communication, resulting
in CORB/RIRB errors. Such events should be rather skipped, as the
codec chip status such as the jack status will be fully refreshed at
the system resume time.
Since we're tracking the system suspend/resume state in codec
power.power_state field, let's add the check in the common unsol event
handler entry point to filter out such events.
The HD-audio controller driver processes the unsolicited events via
its work asynchronously, and this might be pending when the system
goes to suspend. When a lengthy event handling like ELD byte reads is
running, this might trigger unexpected accesses among suspend/resume
procedure, typically seen with Nvidia driver that still requires the
handling via unsolicited event verbs for ELD updates.
This patch adds the flush of unsol_work to assure that pending events
are processed before going into suspend.
The commit c02f77d32d2c ("ALSA: hda - Workaround for crackled sound on
AMD controller (1022:1457)") introduced a few workarounds for the
recent AMD HD-audio controller, and one of them is the forced BATCH
PCM mode so that PulseAudio avoids the timer-based scheduling. This
was thought to cover for some badly working applications, but this
actually worsens for more others. In total, this wasn't a good idea
to enforce it.
This is a partial revert of the commit above for dropping the PCM
BATCH enforcement part to recover from the regression again.
The mute and mic-mute LEDs on HP ZBook Studio G5 are controlled via
GPIO bits 0x10 and 0x20, respectively, and we need the extra setup for
those.
As the similar code is already present for other HP models but with
different GPIO pins, this patch factors out the common helper code and
applies those GPIO values for each model.
The per_pin->work might be still floating at the suspend, and this may
hit the access to the hardware at an unexpected timing. Cancel the
work properly at the suspend callback for avoiding the buggy access.
Note that the bug doesn't trigger easily in the recent kernels since
the work is queued only when the repoll count is set, and usually it's
only at the resume callback, but it's still possible to hit in
theory.
The microphone in the Plantronics C320-M headset will randomly
fail to initialize properly, at least when using Microsoft Teams.
Introducing a 20ms delay on the control messages appears to
resolve the issue.
The GPU GX GDSC has GPU_GX_BCR reset and gfx3d_clk CXC, as stated
on downstream kernels (and as verified upstream, because otherwise
random lockups happen).
Also, add PWRSTS_RET and NO_RET_PERIPH: also as found downstream,
and also as verified here, to avoid GPU related lockups it is
necessary to force retain mem, but *not* peripheral when enabling
this GDSC (and, of course, the inverse on disablement).
With this change, the GPU finally works flawlessly on my four
different MSM8998 devices from two different manufacturers.
TCM buffer length doesn't necessarily equal 8 + ADDITIONAL LENGTH which
might be considered an underflow in case of Data-In size being greater than
8 + ADDITIONAL LENGTH. So truncate buffer length to prevent underflow.
Link: https://lore.kernel.org/r/20210209072202.41154-3-a.miloserdov@yadro.com Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com> Reviewed-by: Bodo Stroesser <bostroesser@gmail.com> Signed-off-by: Aleksandr Miloserdov <a.miloserdov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
TCM doesn't properly handle underflow case for service actions. One way to
prevent it is to always complete command with
target_complete_cmd_with_length(), however it requires access to data_sg,
which is not always available.
This change introduces target_set_cmd_data_length() function which allows
to set command data length before completing it.
Link: https://lore.kernel.org/r/20210209072202.41154-2-a.miloserdov@yadro.com Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com> Reviewed-by: Bodo Stroesser <bostroesser@gmail.com> Signed-off-by: Aleksandr Miloserdov <a.miloserdov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
If iscsi_prep_scsi_cmd_pdu() fails we try to add it back to the cmdqueue,
but we leave it partially setup. We don't have functions that can undo the
pdu and init task setup. We only have cleanup_task which can clean up both
parts. So this has us just fail the cmd and go through the standard cleanup
routine and then have the SCSI midlayer retry it like is done when it fails
in the queuecommand path.
Link: https://lore.kernel.org/r/20210207044608.27585-2-michael.christie@oracle.com Reviewed-by: Lee Duncan <lduncan@suse.com> Signed-off-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Apart from subsystem specific .proc_handler handler, all ctl_tables with
extra1 and extra2 members set should use proc_dointvec_minmax instead of
proc_dointvec, or the limit set in extra* never work and potentially echo
underflow values(negative numbers) is likely make system unstable.
Especially vfs_cache_pressure and zone_reclaim_mode, -1 is apparently not
a valid value, but we can set to them. And then kernel may crash.
No need to store the value for each and every memory block, as we can
easily query the value at runtime. Reshuffle the members to optimize the
memory layout. Also, let's clarify what the interface once was used for
and why it's legacy nowadays.
"phys_device" was used on s390x in older versions of lsmem[2]/chmem[3],
back when they were still part of s390x-tools. They were later replaced
by the variants in linux-utils. For example, RHEL6 and RHEL7 contain
lsmem/chmem from s390-utils. RHEL8 switched to versions from util-linux
on s390x [4].
"phys_device" was added with sysfs support for memory hotplug in commit 3947be1969a9 ("[PATCH] memory hotplug: sysfs and add/remove functions") in
2005. It always returned 0.
s390x started returning something != 0 on some setups (if sclp.rzm is set
by HW) in 2010 via commit 57b552ba0b2f ("memory hotplug/s390: set
phys_device").
For s390x, it allowed for identifying which memory block devices belong to
the same storage increment (RZM). Only if all memory block devices
comprising a single storage increment were offline, the memory could
actually be removed in the hypervisor.
Since commit e5d709bb5fb7 ("s390/memory hotplug: provide
memory_block_size_bytes() function") in 2013 a memory block device spans
at least one storage increment - which is why the interface isn't really
helpful/used anymore (except by old lsmem/chmem tools).
There were once RFC patches to make use of "phys_device" in ACPI context;
however, the underlying problem could be solved using different interfaces
[1].
Avoid a potentially large stack frame and overflow by making
"cpumask_t avail" a static variable. There is no concurrent
access due to the existing locking.
Since the hardware tag-based KASAN mode might not have a redzone that
comes after an allocated object (when kasan.mode=prod is enabled), the
kasan_bitops_tags() test ends up corrupting the next object in memory.
Change the test so it always accesses the redzone that lies within the
allocated object's boundaries.
Overwriting the frozen detected status with the result of the link reset
loses the NEED_RESET result that drivers are depending on for error
handling to report the .slot_reset() callback. Retain this status so
that subsequent error handling has the correct flow.
Struct i40e_veb is allocated in function i40e_setup_pf_switch, and
stored to an array field veb inside struct i40e_pf. However when
i40e_setup_misc_vector fails, this memory leaks.
Fix this by calling exit and teardown functions.
Signed-off-by: Keita Suzuki <keitasuzuki.park@sslab.ics.keio.ac.jp> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
projects / mirror_ubuntu-hirsute-kernel.git / log