The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
a CPU cooling device is found by referring to the cpufreq table instead.
Remove the unused properties from the CPU nodes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Introduce a new flag, uc_buffer, to indicate that the controller
requires the non-cached pages for stream buffers, either as a
chip-specific requirement or specified via snoop=0 option.
This improves the code-readability.
Also, this patch fixes the incorrect behavior for C-Media chip where
the stream buffers were never handled as non-cached due to the check
of driver_type even if you pass snoop=0 option.
Don't reset the resp opcode for a replayed read response.
The resp opcode could be in the middle of a write or send
sequence, when the duplicate read request was received.
An example sequence is as follows:
- Receive read request for 12KB PSN 20. Transmit read response
first, middle and last with PSNs 20,21,22.
- Receive write first PSN 23.
At this point the resp psn is 24 and resp opcode is write first.
- The sender notices that PSN 20 is dropped and retransmits.
Receive read request for 12KB PSN 20. Transmit read response
first, middle and last with PSNs 20,21,22. The resp opcode is
set to -1, the resp psn remains 24.
- Receive write first PSN 23. This is processed by duplicate_request().
The resp opcode remains -1 and resp psn remains 24.
- Receive write middle PSN 24. check_op_seq() reports a missing
first error since the resp opcode is -1.
When sending an ack for a duplicate send or write request,
use the psn of the previous ack sent. Do not use the psn
of a read response for the ack.
An example sequence is as follows:
- Receive write PSN 30. Transmit ACK for PSN 30.
- Receive read request 4KB PSN 31. Transmit read response with
PSN 31. The resp psn is now 32.
- The sender notices that PSN 30 is dropped and retransmits.
Receive write PSN 30. duplicate_request() sends an ACK with
PSN 31. That is incorrect since PSN 31 was a read request.
The driver calls clk_get() with the clock name set to NULL, which means
that the driver could only work when probed from devicetree. From now
on, we explicitly require the driver to be probed from devicetree.
The IRQ work is added before the struct rtc is allocated and registered,
but this struct is used in the IRQ handler. This may lead to a NULL pointer
dereference.
Switch to devm_rtc_allocate_device/rtc_register_device to allocate the rtc
before calling menelaus_add_irq_work.
Also, this solves a possible leak as the RTC is never released.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Instead of playing whack-a-mole and changing SEND_SIG_PRIV to
SEND_SIG_FORCED throughout the kernel to ensure a pid namespace init
gets signals sent by the kernel, stop allowing a pid namespace init to
ignore SIGKILL or SIGSTOP sent by the kernel. A pid namespace init is
only supposed to be able to ignore signals sent from itself and
children with SIG_DFL.
Fixes: 921cf9f63089 ("signals: protect cinit from unblocked SIG_DFL signals") Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Now, we depend on fsck to ensure quota file data is ok,
so we scan whole partition if checkpoint without umount
flag. It's same for quota off error case, which may make
quota file data inconsistent.
On io completion, the driver is taking an adapter wide lock and nulling the
scsi command back pointer. The nulling of the back pointer is to signify the
io was completed and the scsi_done() routine was called. However, the routine
makes no check to see if the abort routine had done the same thing and
possibly nulled the pointer. Thus it may doubly-complete the io.
Make the following mods:
- Check to make sure forward progress (call scsi_done()) only happens if the
command pointer was non-null.
- As the taking of the lock, which is adapter wide, is very costly on a system
under load, null the pointer using an xchg operation rather than under lock.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When running an mds diagnostic that passes frames with the switch, soft
lockups are detected. The driver is in a CQE processing loop and has
sufficient amount of traffic that it never exits the ring processing routine,
thus the "lockup".
Cap the number of elements in the work processing routine to 64 elements. This
ensures that the cpu will be given up and the handler reschedule to process
additional items.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
According to the synchronization rule for the del_timer_sync() function,
the caller must not hold locks which would prevent completion of the
timer's handler.
The timer structure has its own lock that manages its synchronization.
Setting the IOAT_CHAN_DOWN bit should prevent other CPUs from
trying to use that device anyway, there is probably no need to call
del_timer_sync() while holding the prep_lock. So the del_timer_sync()
call is now moved outside of the prep_lock critical section to prevent
the circular lock dependency.
Signed-off-by: Waiman Long <longman@redhat.com> Reviewed-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The ChipIdea IRQ is disabled before scheduling the otg work and
re-enabled on otg work completion. However if the job is already
scheduled we have to undo the effect of disable_irq int order to
balance the IRQ disable-depth value.
Fixes: be6b0c1bd0be ("usb: chipidea: using one inline function to cover queue work operations") Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
drivers/crypto/caam/regs.h:95:1: sparse: incorrect type in return expression (different base types) @@ expected unsigned int @@ got restricted __le32unsigned int @@
drivers/crypto/caam/regs.h:95:1: expected unsigned int
drivers/crypto/caam/regs.h:95:1: got restricted __le32 [usertype] <noident>
drivers/crypto/caam/regs.h:95:1: sparse: incorrect type in return expression (different base types) @@ expected unsigned int @@ got restricted __be32unsigned int @@
drivers/crypto/caam/regs.h:95:1: expected unsigned int
drivers/crypto/caam/regs.h:95:1: got restricted __be32 [usertype] <noident>
drivers/crypto/caam/regs.h:92:1: sparse: cast to restricted __le32
drivers/crypto/caam/regs.h:92:1: sparse: cast to restricted __be32
Errata i870 is applicable in both EP and RC mode. Therefore rename
function dra7xx_pcie_ep_unaligned_memaccess(), that implements errata
workaround, to dra7xx_pcie_unaligned_memaccess() and call it for both RC
and EP. Make sure driver probe does not fail in case the workaround is not
applied for RC mode in order to maintain DT backward compatibility.
Reported-by: Chris Welch <Chris.Welch@viavisolutions.com> Signed-off-by: Vignesh R <vigneshr@ti.com>
[lorenzo.pieralisi@arm.com: reworded the log] Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We want to keep the WARN_ON() and stack trace so the driver can be fixed,
but we can avoid the kernel panic by returning an error. We may still get
warnings like this:
If we change the number of array's device after device is removed from array,
then add the device back to array, we can see that device is added as active
role instead of spare which we expected.
Please see the below link for details:
https://marc.info/?l=linux-raid&m=153736982015076&w=2
This is caused by that we prefer to use device's previous role which is
recorded by saved_raid_disk, but we should respect the new number of
conf->raid_disks since it could be changed after device is removed.
Reported-by: Gioh Kim <gi-oh.kim@profitbricks.com> Tested-by: Gioh Kim <gi-oh.kim@profitbricks.com> Acked-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If the starting block number of either the source or destination file
exceeds the EOF, EXT4_IOC_MOVE_EXT should return EINVAL.
Also fixed the helper function mext_check_coverage() so that if the
logical block is beyond EOF, make it return immediately, instead of
looping until the block number wraps all the away around. This takes
long enough that if there are multiple threads trying to do pound on
an the same inode doing non-sensical things, it can end up triggering
the kernel's soft lockup detector.
We enable power management automatically for bridges where
pci_bridge_d3_possible() returns true. However, these bridges may have
ACPI methods such as _DSW that need to be called before D3 entry. For
example in Lenovo Thinkpad X1 Carbon 6th _DSW method is used to prepare
D3cold for the PCIe root port hosting Thunderbolt chain. Because wake is
not enabled _DSW method is never called and the port does not enter
D3cold properly consuming more power than necessary.
Users can work this around by writing "enabled" to "wakeup" sysfs file
under the device in question but that is not something an ordinary user
is expected to do.
Since we already automatically enable power management for PCIe ports
with ->bridge_d3 set extend that to enable wake for them as well,
assuming the port has any ACPI wakeup related objects implemented in the
namespace (adev->wakeup.flags.valid is true). This ensures the necessary
ACPI methods get called at appropriate times and allows the root port in
Thinkpad X1 Carbon 6th to go into D3cold.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When adding a VMCI resource, the check for an existing entry
would ignore that the new entry could be a wildcard. This could
result in multiple resource entries that would match a given
handle. One disastrous outcome of this is that the
refcounting used to ensure that delayed callbacks for VMCI
datagrams have run before the datagram is destroyed can be
wrong, since the refcount could be increased on the duplicate
entry. This in turn leads to a use after free bug. This issue
was discovered by Hangbin Liu using KASAN and syzkaller.
A cpumask structure on the stack can cause a warning with
CONFIG_NR_CPUS=8192 (e.g. Ubuntu 16.04 and 18.04 use this):
drivers/hv//channel_mgmt.c: In function ‘init_vp_index’:
drivers/hv//channel_mgmt.c:702:1: warning: the frame size of 1032 bytes
is larger than 1024 bytes [-Wframe-larger-than=]
Nowadays it looks most distros enable CONFIG_CPUMASK_OFFSTACK=y, and
hence we can work around the warning by using cpumask_var_t.
Signed-off-by: Dexuan Cui <decui@microsoft.com> Cc: K. Y. Srinivasan <kys@microsoft.com> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: <Stable@vger.kernel.org> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For TPM 1.2 chips the system setup utility allows to set the TPM device in
one of the following states:
* Active: Security chip is functional
* Inactive: Security chip is visible, but is not functional
* Disabled: Security chip is hidden and is not functional
When choosing the "Inactive" state, the TPM 1.2 device is enumerated and
registered, but sending TPM commands fail with either TPM_DEACTIVATED or
TPM_DISABLED depending if the firmware deactivated or disabled the TPM.
Since these TPM 1.2 error codes don't have special treatment, inactivating
the TPM leads to a very noisy kernel log buffer that shows messages like
the following:
tpm_tis 00:05: 1.2 TPM (device-id 0x0, rev-id 78)
tpm tpm0: A TPM error (6) occurred attempting to read a pcr value
tpm tpm0: TPM is disabled/deactivated (0x6)
tpm tpm0: A TPM error (6) occurred attempting get random
tpm tpm0: A TPM error (6) occurred attempting to read a pcr value
ima: No TPM chip found, activating TPM-bypass! (rc=6)
tpm tpm0: A TPM error (6) occurred attempting get random
tpm tpm0: A TPM error (6) occurred attempting get random
tpm tpm0: A TPM error (6) occurred attempting get random
tpm tpm0: A TPM error (6) occurred attempting get random
Let's just suppress error log messages for the TPM_{DEACTIVATED,DISABLED}
return codes, since this is expected when the TPM 1.2 is set to Inactive.
In that case the kernel log is cleaner and less confusing for users, i.e:
The Mediatek's host controller has two slots, each with its own control
registers. The host driver needs to identify what slot is connected to
what port in order to access the device's configuration space.
Current code retrieving slot connected to a given endpoint device.
Assuming each slot is connected to one endpoint device as below:
host bridge
bus 0 --> __________|_______
| |
| |
slot 0 slot 1
bus 1 -->| bus 2 --> |
| |
EP 0 EP 1
During PCI enumeration, system software will scan all the PCI devices on
every bus starting from devfn 0. Using PCI_SLOT(devfn) for matching an
endpoint to its slot is erroneous in that the devfn does not contain the
hierarchical bus numbering in it. In order to match an endpoint with its
slot (and related port), the PCI tree must be walked up to the root bus
(where the root ports are situated) and then the PCI_SLOT(devfn)
matching logic can be correctly applied for matching.
This patch fixes the mtk_pcie_find_port() slot matching logic by adding
appropriate PCI tree walking code to retrieve the slot/port a given
endpoint is connected to.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
[lorenzo.pieralisi@arm.com: rewrote the commit log] Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
atmel,oc-gpio is optional. Request its irq only when atmel,oc is set
in device tree.
devm_gpiod_get_index_optional returns NULL if -ENOENT. Check its
return value for NULL before error, because it is more probable that
atmel,oc is not set.
This fixes the following errors on boards where atmel,oc is not set in
device tree:
[ 0.960000] at91_ohci 500000.ohci: failed to request gpio "overcurrent" IRQ
[ 0.960000] at91_ohci 500000.ohci: failed to request gpio "overcurrent" IRQ
[ 0.970000] at91_ohci 500000.ohci: failed to request gpio "overcurrent" IRQ
Fix possible recursive lock warning. Its a false warning as the locks are
part of two differnt HW Queue data structure - cmdq and creq. Debug kernel
is throwing the following warning and stack trace.
[ 783.914967] ============================================
[ 783.914970] WARNING: possible recursive locking detected
[ 783.914973] 4.19.0-rc2+ #33 Not tainted
[ 783.914976] --------------------------------------------
[ 783.914979] swapper/2/0 is trying to acquire lock:
[ 783.914982] 000000002aa3949d (&(&hwq->lock)->rlock){..-.}, at: bnxt_qplib_service_creq+0x232/0x350 [bnxt_re]
[ 783.914999]
but task is already holding lock:
[ 783.915002] 00000000be73920d (&(&hwq->lock)->rlock){..-.}, at: bnxt_qplib_service_creq+0x2a/0x350 [bnxt_re]
[ 783.915013]
other info that might help us debug this:
[ 783.915016] Possible unsafe locking scenario:
IPCB should be cleared before icmp_send, since it may contain data from
previous layers and the data could be misinterpreted as ip header options,
which later caused the ihl to be set to an invalid value and resulted in
the following stack corruption:
[ 1083.031512] ib0: packet len 57824 (> 2048) too long to send, dropping
[ 1083.031843] ib0: packet len 37904 (> 2048) too long to send, dropping
[ 1083.032004] ib0: packet len 4040 (> 2048) too long to send, dropping
[ 1083.032253] ib0: packet len 63800 (> 2048) too long to send, dropping
[ 1083.032481] ib0: packet len 23960 (> 2048) too long to send, dropping
[ 1083.033149] ib0: packet len 63800 (> 2048) too long to send, dropping
[ 1083.033439] ib0: packet len 63800 (> 2048) too long to send, dropping
[ 1083.033700] ib0: packet len 63800 (> 2048) too long to send, dropping
[ 1083.034124] ib0: packet len 63800 (> 2048) too long to send, dropping
[ 1083.034387] ==================================================================
[ 1083.034602] BUG: KASAN: stack-out-of-bounds in __ip_options_echo+0xf08/0x1310
[ 1083.034798] Write of size 4 at addr ffff880353457c5f by task kworker/u16:0/7
[ 1083.034990]
[ 1083.035104] CPU: 7 PID: 7 Comm: kworker/u16:0 Tainted: G O 4.19.0-rc5+ #1
[ 1083.035316] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu2 04/01/2014
[ 1083.035573] Workqueue: ipoib_wq ipoib_cm_skb_reap [ib_ipoib]
[ 1083.035750] Call Trace:
[ 1083.035888] dump_stack+0x9a/0xeb
[ 1083.036031] print_address_description+0xe3/0x2e0
[ 1083.036213] kasan_report+0x18a/0x2e0
[ 1083.036356] ? __ip_options_echo+0xf08/0x1310
[ 1083.036522] __ip_options_echo+0xf08/0x1310
[ 1083.036688] icmp_send+0x7b9/0x1cd0
[ 1083.036843] ? icmp_route_lookup.constprop.9+0x1070/0x1070
[ 1083.037018] ? netif_schedule_queue+0x5/0x200
[ 1083.037180] ? debug_show_all_locks+0x310/0x310
[ 1083.037341] ? rcu_dynticks_curr_cpu_in_eqs+0x85/0x120
[ 1083.037519] ? debug_locks_off+0x11/0x80
[ 1083.037673] ? debug_check_no_obj_freed+0x207/0x4c6
[ 1083.037841] ? check_flags.part.27+0x450/0x450
[ 1083.037995] ? debug_check_no_obj_freed+0xc3/0x4c6
[ 1083.038169] ? debug_locks_off+0x11/0x80
[ 1083.038318] ? skb_dequeue+0x10e/0x1a0
[ 1083.038476] ? ipoib_cm_skb_reap+0x2b5/0x650 [ib_ipoib]
[ 1083.038642] ? netif_schedule_queue+0xa8/0x200
[ 1083.038820] ? ipoib_cm_skb_reap+0x544/0x650 [ib_ipoib]
[ 1083.038996] ipoib_cm_skb_reap+0x544/0x650 [ib_ipoib]
[ 1083.039174] process_one_work+0x912/0x1830
[ 1083.039336] ? wq_pool_ids_show+0x310/0x310
[ 1083.039491] ? lock_acquire+0x145/0x3a0
[ 1083.042312] worker_thread+0x87/0xbb0
[ 1083.045099] ? process_one_work+0x1830/0x1830
[ 1083.047865] kthread+0x322/0x3e0
[ 1083.050624] ? kthread_create_worker_on_cpu+0xc0/0xc0
[ 1083.053354] ret_from_fork+0x3a/0x50
For instance __ip_options_echo is failing to proceed with invalid srr and
optlen passed from another layer via IPCB
If the provider driver (such as rdma_rxe) doesn't support pma counters,
avoid exposing its directory similar to optional hw_counters directory.
If core fails to read the PMA counter, return an error so that user can
retry later if needed.
In megasas_mgmt_compat_ioctl_fw(), to handle the structure
compat_megasas_iocpacket 'cioc', a user-space structure megasas_iocpacket
'ioc' is allocated before megasas_mgmt_ioctl_fw() is invoked to handle
the packet. Since the two data structures have different fields, the data
is copied from 'cioc' to 'ioc' field by field. In the copy process,
'sense_ptr' is prepared if the field 'sense_len' is not null, because it
will be used in megasas_mgmt_ioctl_fw(). To prepare 'sense_ptr', the
user-space data 'ioc->sense_off' and 'cioc->sense_off' are copied and
saved to kernel-space variables 'local_sense_off' and 'user_sense_off'
respectively. Given that 'ioc->sense_off' is also copied from
'cioc->sense_off', 'local_sense_off' and 'user_sense_off' should have the
same value. However, 'cioc' is in the user space and a malicious user can
race to change the value of 'cioc->sense_off' after it is copied to
'ioc->sense_off' but before it is copied to 'user_sense_off'. By doing
so, the attacker can inject different values into 'local_sense_off' and
'user_sense_off'. This can cause undefined behavior in the following
execution, because the two variables are supposed to be same.
This patch enforces a check on the two kernel variables 'local_sense_off'
and 'user_sense_off' to make sure they are the same after the copy. In
case they are not, an error code EINVAL will be returned.
Signed-off-by: Wenwen Wang <wang6495@umn.edu> Acked-by: Sumit Saxena <sumit.saxena@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
According to volume 3 of the SDM, bits 63:15 and 12:4 of the exit
qualification field for debug exceptions are reserved (cleared to
0). However, the SDM is incorrect about bit 16 (corresponding to
DR6.RTM). This bit should be set if a debug exception (#DB) or a
breakpoint exception (#BP) occurred inside an RTM region while
advanced debugging of RTM transactional regions was enabled. Note that
this is the opposite of DR6.RTM, which "indicates (when clear) that a
debug exception (#DB) or breakpoint exception (#BP) occurred inside an
RTM region while advanced debugging of RTM transactional regions was
enabled."
There is still an issue with stale DR6 bits potentially being
misreported for the current debug exception. DR6 should not have been
modified before vectoring the #DB exception, and the "new DR6 bits"
should be available somewhere, but it was and they aren't.
Fixes: b96fb439774e1 ("KVM: nVMX: fixes to nested virt interrupt injection") Signed-off-by: Jim Mattson <jmattson@google.com> Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
(2) g++ does not support "non-trivial" array initialisers fully yet.
(3) Every file that calls this function will acquire a copy of names[].
The same goes for nvdimm_cmd_name().
Fix all three by converting to a switch statement where each case returns a
string. That way if cmd is a constant, the compiler can trivially reduce it
and, if not, the compiler can use a shared lookup table if it thinks that is
more efficient.
A better way would be to remove these functions and their arrays from the
header entirely.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If a target disconnects during a PIO data transfer the command may fail
when the target reconnects:
scsi host1: DMA length is zero!
scsi host1: cur adr[04380000] len[00000000]
The scsi bus is then reset. This happens because the residual reached
zero before the transfer was completed.
The usual residual calculation relies on the Transfer Count registers.
That works for DMA transfers but not for PIO transfers. Fix the problem
by storing the PIO transfer residual and using that to correctly
calculate bytes_sent.
Fixes: 6fe07aaffbf0 ("[SCSI] m68k: new mac_esp scsi driver") Tested-by: Stan Johnson <userm57@yahoo.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If a cgroup has many tasks with many open file descriptors then we would
end up in a large loop without any rescheduling point throught the
operation. Add cond_resched once per task.
The workqueue used for monitoring the hardware may run while the device
is already suspended. Fix this by using the freezable system workqueue
instead, cfr. commit 51e20d0e3a60cf46 ("thermal: Prevent polling from
happening during system suspend").
When running in AP mode, ath10k sometimes suffers from TX credit
starvation. The issue is hard to reproduce and shows up once in a
few days, but has been repeatedly seen with QCA9882 and a large
range of firmwares, including 10.2.4.70.67.
Once the module is in this state, TX credits are never replenished,
which results in "SWBA overrun" errors, as no beacons can be sent.
Even worse, WMI commands run in a timeout while holding the conf
mutex for three seconds each, making any further operations slow
and the whole system unresponsive.
The firmware/driver never recovers from that state automatically,
and triggering TX flush or warm restarts won't work over WMI. So
issue a hardware restart if a WMI command times out due to missing
TX credits. This implies a connectivity outage of about 1.4s in AP
mode, but brings back the interface and the whole system to a usable
state. WMI command timeouts have not been seen in absent of this
specific issue, so taking such drastic actions seems legitimate.
Signed-off-by: Martin Willi <martin@strongswan.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
While VF2VF with RSS communication, RSS Type were wrongly recognized
and RSS hash was not calculated as it should be. Packets was
distributed on various queues by accident.
This commit fixes that behaviour and causes proper RSS Type recognition.
Signed-off-by: Sebastian Basierski <sebastianx.basierski@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If you look at "pinconf-groups" in debugfs for ssbi-gpio you'll notice
it looks like nonsense.
The problem is fairly well described in commit 1cf86bc21257 ("pinctrl:
qcom: spmi-gpio: Fix pmic_gpio_config_get() to be compliant") and
commit 05e0c828955c ("pinctrl: msm: Fix msm_config_group_get() to be
compliant"), but it was pointed out that ssbi-gpio has the same
problem. Let's fix it there too.
Fixes: b4c45fe974bc ("pinctrl: qcom: ssbi: Family A gpio & mpp drivers") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Stephen Boyd <sboyd@kernel.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If you look at "pinconf-groups" in debugfs for ssbi-mpp you'll notice
it looks like nonsense.
The problem is fairly well described in commit 1cf86bc21257 ("pinctrl:
qcom: spmi-gpio: Fix pmic_gpio_config_get() to be compliant") and
commit 05e0c828955c ("pinctrl: msm: Fix msm_config_group_get() to be
compliant"), but it was pointed out that ssbi-mpp has the same
problem. Let's fix it there too.
NOTE: in case it's helpful to someone reading this, the way to tell
whether to do the -EINVAL or not is to look at the PCONFDUMP for a
given attribute. If the last element (has_arg) is false then you need
to do the -EINVAL trick.
ALSO NOTE: it seems unlikely that the values returned when we try to
get PIN_CONFIG_BIAS_PULL_UP will actually be printed since "has_arg"
is false for that one, but I guess it's still fine to return different
values so I kept doing that. It seems like another driver (ssbi-gpio)
uses a custom attribute (PM8XXX_QCOM_PULL_UP_STRENGTH) for something
similar so maybe a future change should do that here too.
It looks like we parse the drive strength setting here, but never
actually write it into the hardware to update it. Parse the setting and
then write it at the end of the pinconf setting function so that it
actually sticks in the hardware.
Fixes: 0e948042c420 ("pinctrl: qcom: spmi-mpp: Implement support for sink mode") Cc: Doug Anderson <dianders@chromium.org> Signed-off-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Bay and Cherry Trail DSTDs represent a different set of devices depending
on which OS the device think it is booting. One set of decices for Windows
and another set of devices for Android which targets the Android-x86 Linux
kernel fork (which e.g. used to have its own display driver instead of
using the i915 driver).
Which set of devices we are actually going to get is out of our control,
this is controlled by the ACPI OSID variable, which gets either set through
an EFI setup option, or sometimes is autodetected. So we need to support
both.
This commit adds support for the 80862286 and 808622C0 ACPI HIDs which we
get for the first resp. second DMA controller on Cherry Trail devices when
OSID is set to Android.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
BFQ schedules entities (which represent either per-process queues or
groups of queues) as a function of their timestamps. In particular, as
a function of their (virtual) finish times. The finish time of an
entity is computed as a function of the budget assigned to the entity,
assuming, tentatively, that the entity, once in service, will receive
an amount of service equal to its budget. Then, when the entity is
expired because it finishes to be served, this finish time is updated
as a function of the actual service received by the entity. This
allows the entity to be correctly charged with only the service
received, and then to be correctly re-scheduled.
Yet an entity may receive service also while not being the entity in
service (in the scheduling environment of its parent entity), for
several reasons. If the entity remains with no backlog while receiving
this 'unofficial' service, then it is expired. Also on such an
expiration, the finish time of the entity should be updated to account
for only the service actually received by the entity. Unfortunately,
such an update is not performed for an entity expiring without being
the entity in service.
In a similar vein, the service counter of the entity in service is
reset when the entity is expired, to be ready to be used for next
service cycle. This reset too should be performed also in case an
entity is expired because it remains empty after receiving service
while not being the entity in service. But in this case the reset is
not performed.
This commit performs the above update of the finish time and reset of
the service received, also for an entity expiring while not being the
entity in service.
Phylink made an assumption about the carrier state being down when
calling phylink_start(). If this assumption isn't satisfied, the
internal phylink state could misbehave and a net device could end up not
being functional.
This patch fixes this by explicitly calling netif_carrier_off() in
phylink_start().
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Acked-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We currently align the end of the compressed image to a multiple of
16. However, the PE-COFF header included in the EFI stub says that
the file alignment is 32 bytes, and when adding an EFI signature to
the file it must first be padded to this alignment.
sbsigntool commands warn about this:
warning: file-aligned section .text extends beyond end of file
warning: checksum areas are greater than image size. Invalid section table?
Worse, pesign -at least when creating a detached signature- uses the
hash of the unpadded file, resulting in an invalid signature if
padding is required.
Avoid both these problems by increasing alignment to 32 bytes when
CONFIG_EFI_STUB is enabled.
This patch adds the device ID for the AMPAK AP6335 combo module used
in the 1st generation WeTek Hub Android/LibreELEC HTPC box. The WiFI
chip identifies itself as BCM4339, while Bluetooth identifies itself
as BCM4335 (rev C0):
The sigaltstack(2) system call fails with -ENOMEM if the new alternative
signal stack is found to be smaller than SIGMINSTKSZ. On architectures
such as arm64, where the native value for SIGMINSTKSZ is larger than
the compat value, this can result in an unexpected error being reported
to a compat task. See, for example:
This patch fixes the problem by extending do_sigaltstack to take the
minimum signal stack size as an additional parameter, allowing the
native and compat system call entry code to pass in their respective
values. COMPAT_SIGMINSTKSZ is just defined as SIGMINSTKSZ if it has not
been defined by the architecture.
Cc: Arnd Bergmann <arnd@arndb.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Oleg Nesterov <oleg@redhat.com> Reported-by: Steve McIntyre <steve.mcintyre@arm.com> Tested-by: Steve McIntyre <93sam@debian.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There is a potential execution path in which function
of_find_compatible_node() returns NULL. In such a case,
we end up having a NULL pointer dereference when accessing
pointer *nfc_np* in function of_clk_get().
So, we better don't take any chances and fix this by null
checking pointer *nfc_np* before calling of_clk_get().
Addresses-Coverity-ID: 1473052 ("Dereference null return value") Fixes: f88fc122cc34 ("mtd: nand: Cleanup/rework the atmel_nand driver") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We can not call dev_pm_opp_of_cpumask_remove_table() freely anymore
since the latest OPP core updates as that uses reference counting to
free resources. There are cases where no static OPPs are added (using
DT) for a platform and trying to remove the OPP table may end up
decrementing refcount which is already zero and hence generating
warnings.
Lets track if we were able to add static OPPs or not and then only
remove the table based on that. Some reshuffling of code is also done to
do that.
ACPI driver should make sure all the processor IDs in their ACPI Namespace
are unique. the driver performs a depth-first walk of the namespace tree
and calls the acpi_processor_ids_walk() to check the duplicate IDs.
But, the acpi_processor_ids_walk() mistakes the return value. If a
processor is checked, it returns true which causes the walk break
immediately, and other processors will never be checked.
Repace the value with AE_OK which is the standard acpi_status value.
And don't abort the namespace walk even on error.
Fixes: 8c8cb30f49b8 (acpi/processor: Implement DEVICE operator for processor enumeration) Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On OLPC XO-1, the RTC is discovered via device tree from the arch
initcall. Don't let the PC platform register another one from its device
initcall, it's not going to work:
sysfs: cannot create duplicate filename '/devices/platform/rtc_cmos'
CPU: 0 PID: 1 Comm: swapper Not tainted 4.19.0-rc6 #12
Hardware name: OLPC XO/XO, BIOS OLPC Ver 1.00.01 06/11/2014
Call Trace:
dump_stack+0x16/0x18
sysfs_warn_dup+0x46/0x58
sysfs_create_dir_ns+0x76/0x9b
kobject_add_internal+0xed/0x209
? __schedule+0x3fa/0x447
kobject_add+0x5b/0x66
device_add+0x298/0x535
? insert_resource_conflict+0x2a/0x3e
platform_device_add+0x14d/0x192
? io_delay_init+0x19/0x19
platform_device_register+0x1c/0x1f
add_rtc_cmos+0x16/0x31
do_one_initcall+0x78/0x14a
? do_early_param+0x75/0x75
kernel_init_freeable+0x152/0x1e0
? rest_init+0xa2/0xa2
kernel_init+0x8/0xd5
ret_from_fork+0x2e/0x38
kobject_add_internal failed for rtc_cmos with -EEXIST, don't try to
register things with the same name in the same directory.
platform rtc_cmos: registered platform RTC device (no PNP device found)
Fix a bug that happens in the following scenario:
1) suspend without WoWLAN
2) mac80211 calls drv_stop because of the suspend
3) __iwl_mvm_mac_stop deallocates the aux station
4) during drv_stop the firmware crashes
5) iwlmvm:
* sets IWL_MVM_STATUS_HW_RESTART_REQUESTED
* asks mac80211 to kick the restart flow
6) mac80211 puts the restart worker into a freezable
queue which means that the worker will not run for now
since the workqueue is already frozen
7) ...
8) resume
9) mac80211 runs ieee80211_reconfig as part of the resume
10) mac80211 detects that a restart flow has been requested
and that we are now resuming from suspend and cancels
the restart worker
11) mac80211 calls drv_start()
12) __iwl_mvm_mac_start checks that IWL_MVM_STATUS_HW_RESTART_REQUESTED
clears it, sets IWL_MVM_STATUS_IN_HW_RESTART and calls
iwl_mvm_restart_cleanup()
13) iwl_fw_error_dump gets called and accesses the device
to get debug data
14) iwl_mvm_up adds the aux station
15) iwl_mvm_add_aux_sta() allocates an internal station for
the aux station
16) iwl_mvm_allocate_int_sta() tests IWL_MVM_STATUS_IN_HW_RESTART
and doesn't really allocate a station ID for the aux
station
17) a new queue is added for the aux station
Note that steps from 5 to 9 aren't really part of the
problem but were described for the sake of completeness.
Once the iwl_mvm_mac_stop() is called, the device is not
accessible, meaning that step 12) can't succeed and we'll
see the following:
The station id of the aux station is set to 0xff in step 3
and because we don't really allocate a new station id for
the auxliary station (as explained in 16), we end up sending
a command to the firmware asking to connect the queue
to station id 0xff. This makes the firmware crash with the
following information:
Fix this by clearing IWL_MVM_STATUS_HW_RESTART_REQUESTED
in iwl_mvm_mac_stop(). We won't be able to collect debug
data anyway and when we will brought up again, we will
have a clean state from the firmware perspective.
Since we won't have IWL_MVM_STATUS_IN_HW_RESTART set in
step 12) we won't get to the 2093 ASSERT either.
If all free RB queues are empty, the driver will never restock the
free RB queue. That's because the restocking happens in the Rx flow,
and if the free queue is empty there will be no Rx.
Although there's a background worker (a.k.a. allocator) allocating
memory for RBs so that the Rx handler can restock them, the worker may
run only after the free queue has become empty (and then it is too
late for restocking as explained above).
There is a solution for that called 'emergency': If the number of used
RB's reaches half the amount of all RB's, the Rx handler will not wait
for the allocator but immediately allocate memory for the used RB's
and restock the free queue.
But, since the used RB's is per queue, it may happen that the used
RB's are spread between the queues such that the emergency check will
fail for each of the queues
(and still run out of RBs, causing the above symptom).
To fix it, move to emergency mode if the sum of *all* used RBs (for
all Rx queues) reaches half the amount of all RB's
This device reports SDHCI_CLOCK_INT_STABLE even though it's not
ready to take SDHCI_CLOCK_CARD_EN. The symptom is that reading
SDHCI_CLOCK_CONTROL after enabling the clock shows absence of the
bit from the register (e.g. expecting 0x0000fa07 = 0x0000fa03 |
SDHCI_CLOCK_CARD_EN but only observed the first operand).
cpupower crashes on VMWare guests. The guests have the AMD PStateDef MSR
(0xC0010064 + state number) set to zero. As a result fid and did are zero
and the crash occurs because of a divide by zero (cof = fid/did). This
can be prevented by checking the enable bit in the PStateDef MSR before
calculating cof. By doing this the value of pstate[i] remains zero and
the value can be tested before displaying the active Pstates.
Check the enable bit in the PstateDef register for all supported families
and only print out enabled Pstates.
For each system in a given pevent, read_event_files() reads in a
temporary 'sys' string. Be sure to free this string before moving onto
to the next system and/or leaving read_event_files().
Fixes the following coverity complaints:
Error: RESOURCE_LEAK (CWE-772):
tools/perf/util/trace-event-read.c:343: overwrite_var: Overwriting
"sys" in "sys = read_string()" leaks the storage that "sys" points to.
tools/perf/util/trace-event-read.c:353: leaked_storage: Variable "sys"
going out of scope leaks the storage it points to.
Signed-off-by: Sanskriti Sharma <sansharm@redhat.com> Reviewed-by: Jiri Olsa <jolsa@kernel.org> Cc: Joe Lawrence <joe.lawrence@redhat.com> Link: http://lkml.kernel.org/r/1538490554-8161-6-git-send-email-sansharm@redhat.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Clang warns when one enumerated type is implicitly converted to another.
drivers/spi/spi-ep93xx.c:342:62: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
nents = dma_map_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:428:58: note: expanded from macro
'dma_map_sg'
#define dma_map_sg(d, s, n, r) dma_map_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~ ^
drivers/spi/spi-ep93xx.c:348:57: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:429:62: note: expanded from macro
'dma_unmap_sg'
#define dma_unmap_sg(d, s, n, r) dma_unmap_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~~~ ^
drivers/spi/spi-ep93xx.c:377:56: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:429:62: note: expanded from macro
'dma_unmap_sg'
#define dma_unmap_sg(d, s, n, r) dma_unmap_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~~~ ^
3 warnings generated.
dma_{,un}map_sg expect an enum of type dma_data_direction but this
driver uses dma_transfer_direction for everything. Convert the driver to
use dma_data_direction for these two functions.
There are two places that strictly require an enum of type
dma_transfer_direction: the direction member in struct dma_slave_config
and the direction parameter in dmaengine_prep_slave_sg. To avoid using
an explicit cast, add a simple function, ep93xx_dma_data_to_trans_dir,
to safely map between the two types because they are not 1 to 1 in
meaning.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Technically this is not required because disabling the PWM should be
enough. However, when support for atomic operations was implemented in
the PWM subsystem, only actual changes to the PWM channel are applied
during pwm_config(), which means that during after resume from suspend
the old settings won't be applied.
One possible solution is for the PWM driver to implement its own PM
operations such that settings from before suspend get applied on resume.
This has the disadvantage of completely ignoring any particular ordering
requirements that PWM user drivers might have, so it is best to leave it
up to the user drivers to apply the settings that they want at the
appropriate time.
Another way to solve this would be to read back the current state of the
PWM at the time of resume. That way, in case the configuration was lost
during suspend, applying the old settings in PWM user drivers would
actually get them applied because they differ from the current settings.
However, not all PWM drivers support reading the hardware state, and not
all hardware may support it.
The best workaround at this point seems to be to let PWM user drivers
tell the PWM subsystem that the PWM is turned off by, in addition to
disabling it, also setting the duty cycle to 0. This causes the resume
operation to apply a configuration that is different from the current
configuration, resulting in the proper state from before suspend getting
restored.
When running as a level 3 guest with no host provided sthyi support
sclp_ocf_cpc_name_copy() will only return zeroes. Zeroes are not a
valid group name, so let's not indicate that the group name field is
valid.
Also the group name is not dependent on stsi, let's not return based
on stsi before setting it.
Configuring generic network device parameters on tun will fail in
presence of IFLA_INFO_KIND attribute in IFLA_LINKINFO nested attribute
since tun_validate() always return failure.
This can be visualized with following ip-link(8) command sequences:
# ip link set dev tun0 group 100
# ip link set dev tun0 group 100 type tun
RTNETLINK answers: Invalid argument
with contrast to dummy and veth drivers:
# ip link set dev dummy0 group 100
# ip link set dev dummy0 type dummy
# ip link set dev veth0 group 100
# ip link set dev veth0 group 100 type veth
Fix by returning zero in tun_validate() when @data is NULL that is
always in case since rtnl_link_ops->maxtype is zero in tun driver.
Fixes: f019a7a594d9 ("tun: Implement ip link del tunXXX") Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This commit makes it possible to use devlink to split the 100G CXP
Netronome into two 40G interfaces. Currently when you ask for 2
interfaces, the math in src/nfp_devlink.c:nfp_devlink_port_split
calculates that you want 5 lanes per port because for some reason
eth_port.port_lanes=10 (shouldn't this be 12 for CXP?). What we really
want when asking for 2 breakout interfaces is 4 lanes per port. This
commit makes that happen by calculating based on 8 lanes if 10 are
present.
Signed-off-by: Ryan C Goodfellow <rgoodfel@isi.edu> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Greg Weeks <greg.weeks@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If we fail to allocate the request queue for a disk, we still need to
free that disk, not just the previous ones. Additionally, we need to
cleanup the previous request queues.
Move queue allocation next to disk allocation to fix a couple of issues:
- If add_disk() hasn't been called, we should clear disk->queue before
calling put_disk().
- If we fail to allocate a request queue, we still need to put all of
the disks, not just the ones that we allocated queues for.
It was found that when debug_locks was turned off because of a problem
found by the lockdep code, the system performance could drop quite
significantly when the lock_stat code was also configured into the
kernel. For instance, parallel kernel build time on a 4-socket x86-64
server nearly doubled.
Further analysis into the cause of the slowdown traced back to the
frequent call to debug_locks_off() from the __lock_acquired() function
probably due to some inconsistent lockdep states with debug_locks
off. The debug_locks_off() function did an unconditional atomic xchg
to write a 0 value into debug_locks which had already been set to 0.
This led to severe cacheline contention in the cacheline that held
debug_locks. As debug_locks is being referenced in quite a few different
places in the kernel, this greatly slow down the system performance.
To prevent that trashing of debug_locks cacheline, lock_acquired()
and lock_contended() now checks the state of debug_locks before
proceeding. The debug_locks_off() function is also modified to check
debug_locks before calling __debug_locks_off().
Signed-off-by: Waiman Long <longman@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will.deacon@arm.com> Link: http://lkml.kernel.org/r/1539913518-15598-1-git-send-email-longman@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
drivers/net/ethernet/qlogic/qla3xxx.c:384:24: warning: signed shift
result (0xF00000000) requires 37 bits to represent, but 'int' only has
32 bits [-Wshift-overflow]
((ISP_NVRAM_MASK << 16) | qdev->eeprom_cmd_data));
~~~~~~~~~~~~~~ ^ ~~
1 warning generated.
The warning is certainly accurate since ISP_NVRAM_MASK is defined as
(0x000F << 16) which is then shifted by 16, resulting in 64424509440,
well above UINT_MAX.
Given that this is the only location in this driver where ISP_NVRAM_MASK
is shifted again, it seems likely that ISP_NVRAM_MASK was originally
defined without a shift and during the move of the shift to the
definition, this statement wasn't properly removed (since ISP_NVRAM_MASK
is used in the statenent right above this). Only the maintainers can
confirm this since this statment has been here since the driver was
first added to the kernel.
Link: https://github.com/ClangBuiltLinux/linux/issues/127 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The size of the resulting cpu map can be smaller than a multiple of
sizeof(u64), resulting in SIGBUS on cpus like Sparc as the next event
will not be aligned properly.
Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@intel.com> Fixes: 6c872901af07 ("perf cpu_map: Add cpu_map event synthesize function") Link: http://lkml.kernel.org/r/20181011.224655.716771175766946817.davem@davemloft.net Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When a build is run from something like a cron job, the user's $PATH is
rather minimal, of note, not including /usr/sbin in my own case. Because
of that, an automated rpm package build ultimately fails to find
libperf-jvmti.so, because somewhere within the build, this happens...
/bin/sh: alternatives: command not found
/bin/sh: alternatives: command not found
Makefile.config:849: No openjdk development package found, please install
JDK package, e.g. openjdk-8-jdk, java-1.8.0-openjdk-devel
...and while the build continues, libperf-jvmti.so isn't built, and
things fall down when rpm tries to find all the %files specified. Exact
same system builds everything just fine when the job is launched from a
login shell instead of a cron job, since alternatives is in $PATH, so
openjdk is actually found.
The test required to get into this section of code actually specifies
the full path, as does a block just above it, so let's do that here too.
Signed-off-by: Jarod Wilson <jarod@redhat.com> Acked-by: Jiri Olsa <jolsa@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: William Cohen <wcohen@redhat.com> Fixes: d4dfdf00d43e ("perf jvmti: Plug compilation into perf build") Link: http://lkml.kernel.org/r/20180906221812.11167-1-jarod@redhat.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Michael reported that he could not stat following event:
$ perf stat -e unc_p_freq_ge_1200mhz_cycles -a -- ls
event syntax error: '..e_1200mhz_cycles'
\___ value too big for format, maximum is 255
Run 'perf list' for a list of valid events
The event is unwrapped into:
uncore_pcu/event=0xb,filter_band0=1200/
where filter_band0 format says it's one byte only:
Michael reported an issue with oversized terms values assignment
and I noticed there was actually a misunderstanding of the max
value check in the past.
The above commit's changelog says:
If bit 21 is set, there is parsing issues as below.
$ perf stat -a -e uncore_qpi_0/event=0x200002,umask=0x8/
event syntax error: '..pi_0/event=0x200002,umask=0x8/'
\___ value too big for format, maximum is 511
But there's no issue there, because the event value is distributed
along the value defined by the format. Even if the format defines
separated bit, the value is treated as a continual number, which
should follow the format definition.
In above case it's 9-bit value with last bit separated:
$ cat uncore_qpi_0/format/event
config:0-7,21
Hence the value 0x200002 is correctly reported as format violation,
because it exceeds 9 bits. It should have been 0x102 instead, which
sets the 9th bit - the bit 21 of the format.
$ perf stat -vv -a -e uncore_qpi_0/event=0x102,umask=0x8/
Using CPUID GenuineIntel-6-2D
...
------------------------------------------------------------
perf_event_attr:
type 10
size 112
config 0x200802
sample_type IDENTIFIER
...
Reported-by: Michael Petlan <mpetlan@redhat.com> Signed-off-by: Jiri Olsa <jolsa@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Fixes: ac0e2cd55537 ("perf tools: Fix PMU term format max value calculation") Link: http://lkml.kernel.org/r/20181003072046.29276-1-jolsa@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
PMIC_IRQB and PMIC_KEYINB lines on Exynos4210-based Origen board have
external pull-up resistors, so disable any pull control for those lines
in respective pin controller node. This fixes support for MAX8997
interrupts and enables operation of wakeup from MAX8997 RTC alarm.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Fixes: 17419726aaa1 ("ARM: dts: add max8997 device node for exynos4210-origen board") Cc: <stable@vger.kernel.org> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
memory_corruption_check[{_period|_size}]()'s handlers do not check input
argument before passing it to kstrtoul() or simple_strtoull(). The argument
would be a NULL pointer if each of the kernel parameters, without its
value, is set in command line and thus cause the following panic.
The boot loader version reported via sysfs is wrong in case of the
kernel being booted via the Xen PVH boot entry. it should be 2.12
(0x020c), but it is reported to be 2.18 (0x0212).
As the current way to set the version is error prone use the more
readable variant (2 << 8) | 12.
The Creative Audigy SE (SB0570) card currently exhibits an audible pop
whenever playback is stopped or resumed, or during silent periods of an
audio stream. Initialise the IZD bit to the 0 to eliminate these pops.
The Infinite Zero Detection (IZD) feature on the DAC causes the output
to be shunted to Vcap after 2048 samples of silence. This discharges the
AC coupling capacitor through the output and causes the aforementioned
pop/click noise.
The behaviour of the IZD bit is described on page 15 of the WM8768GEDS
datasheet: "With IZD=1, applying MUTE for 1024 consecutive input samples
will cause all outputs to be connected directly to VCAP. This also
happens if 2048 consecutive zero input samples are applied to all 6
channels, and IZD=0. It will be removed as soon as any channel receives
a non-zero input". I believe the second sentence might be referring to
IZD=1 instead of IZD=0 given the observed behaviour of the card.
This change should make the DAC initialisation consistent with
Creative's Windows driver, as this popping persists when initialising
the card in Linux and soft rebooting into Windows, but is not present on
a cold boot to Windows.
BIOS on ASUS G751 doesn't seem to map the headphone pin (NID 0x16)
correctly. Add a quirk to address it, as well as chaining to the
previous fix for the microphone.
In the C-code we need to put the physical address of the hpmc handler in
the interrupt vector table (IVA) in order to get HPMCs working. Since
on parisc64 function pointers are indirect (in fact they are function
descriptors) we instead export the address as variable and not as
function.
This reverts a small part of commit f39cce654f9a ("parisc: Add
cfi_startproc and cfi_endproc to assembly code").
Fix a long-existing small nasty bug in the map_pages() implementation which
leads to overwriting already written pte entries with zero, *if* map_pages() is
called a second time with an end address which isn't aligned on a pmd boundry.
This happens for example if we want to remap only the text segment read/write
in order to run alternative patching on the code. Exiting the loop when we
reach the end address fixes this.
Helge noticed that the address of the os_hpmc handler was not being
correctly calculated in the hpmc macro. As a result, PDCE_CHECK would
fail to call os_hpmc:
Currently, "disable_clkrun" yenta_socket module parameter is only
implemented for TI CardBus bridges.
Add also an implementation for Ricoh bridges that have the necessary
setting documented in publicly available datasheets.
Tested on a RL5C476II with a Sunrich C-160 CardBus NIC that doesn't work
correctly unless the CLKRUN protocol is disabled.
Let's also make it clear in its description that the "disable_clkrun"
module parameter only works on these two previously mentioned brands of
CardBus bridges.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name> Cc: stable@vger.kernel.org Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If the policy limits change between invocations of cs_dbs_update(),
the requested frequency value stored in dbs_info may not be updated
and the function may use a stale value of it next time. Moreover, if
idle periods are takem into account by cs_dbs_update(), the requested
frequency value stored in dbs_info may be below the min policy limit,
which is incorrect.
To fix these problems, always update the requested frequency value
in dbs_info along with the local copy of it when the previous
requested frequency is beyond the policy limits and avoid decreasing
the requested frequency below the min policy limit when taking
idle periods into account.
Fixes: abb6627910a1 (cpufreq: conservative: Fix next frequency selection) Fixes: 00bfe05889e9 (cpufreq: conservative: Decrease frequency faster for deferred updates) Reported-by: Waldemar Rymarkiewicz <waldemarx.rymarkiewicz@intel.com> Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Waldemar Rymarkiewicz <waldemarx.rymarkiewicz@intel.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When an invalid mount option is passed to jffs2, jffs2_parse_options()
will fail and jffs2_sb_info will be freed, but then jffs2_sb_info will
be used (use-after-free) and freeed (double-free) in jffs2_kill_sb().
Fix it by removing the buggy invocation of kfree() when getting invalid
mount options.
Fixes: 92abc475d8de ("jffs2: implement mount option parsing and compression overriding") Cc: stable@kernel.org Signed-off-by: Hou Tao <houtao1@huawei.com> Reviewed-by: Richard Weinberger <richard@nod.at> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Devices with compatible="pmbus" field have zero initial page count,
and pmbus_clear_faults() being called before the page count auto-
detection does not actually clear faults because it depends on the
page count. Non-cleared faults in its turn may fail the subsequent
page count auto-detection.
This patch fixes this problem by calling pmbus_clear_fault_page()
for currently set page and calling pmbus_clear_faults() after the
page count was detected.
refill->end record the last key of writeback, for example, at the first
time, keys (1,128K) to (1,1024K) are flush to the backend device, but
the end key (1,1024K) is not included, since the bellow code:
if (bkey_cmp(k, refill->end) >= 0) {
ret = MAP_DONE;
goto out;
}
And in the next time when we refill writeback keybuf again, we searched
key start from (1,1024K), and got a key bigger than it, so the key
(1,1024K) missed.
This patch modify the above code, and let the end key to be included to
the writeback key buffer.
Missed reading IOs are identified by s->cache_missed, not the
s->cache_miss, so in trace_bcache_read() using trace_bcache_read
to identify whether the IO is missed or not.
projects / mirror_ubuntu-bionic-kernel.git / log