Add the power domains names to the power domain struct so we
have meaningful name for every power domain. This also removes the
following debugfs error message.
This clock must be always enabled to allow access to any registers in
fsys1 CMU. Until proper solution based on runtime PM is applied
(similar to what was done for Exynos5433), mark that clock as critical
so it won't be disabled.
It was observed on Samsung Galaxy S6 device (based on Exynos7420), where
UFS module is probed before pmic used to power that device.
In this case defer probe was happening and that clock was disabled by
UFS driver, causing whole boot to hang on next CMU access.
Fixes: 753195a749a6 ("clk: samsung: exynos7: Correct CMU_FSYS1 clocks names") Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> Acked-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/linux-clk/20201024154346.9589-1-pawel.mikolaj.chmiel@gmail.com
[s.nawrocki: Added comment in the code] Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The retire logic uses the 2 lower bits of the pointer to the retire
function to store flags. However, the auto_retire function is not
guaranteed to be aligned to a multiple of 4, which causes crashes as
we jump to the wrong address, for example like this:
__i915_active_call annotation is required on the retire callback to ensure
correct function alignment.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Fixes: a21ce8ad12d2 ("drm/i915/overlay: Switch to using i915_active tracking") Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Matthew Auld <matthew.auld@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210429083530.849546-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit d8e44e4dd221ee283ea60a6fb87bca08807aa0ab) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We've defined C0DRB3/C1DRB3 as 16 bit registers, so access them
as such.
Fixes: 1c8242c3a4b2 ("drm/i915: Use unchecked writes for setting up the fences") Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210421153401.13847-3-ville.syrjala@linux.intel.com
(cherry picked from commit f765a5b48c667bdada5e49d5e0f23f8c0687b21b) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Link status is different from display connected status in the case
of something like an Apple dongle where the type-c plug can be
connected, and therefore the link is connected, but no sink is
connected until an HDMI cable is plugged into the dongle.
The sink_count of DPCD of dongle will increase to 1 once an HDMI
cable is plugged into the dongle so that display connected status
will become true. This checking also apply at pm_resume.
Changes in v4:
-- none
Fixes: 94e58e2d06e3 ("drm/msm/dp: reset dp controller only at boot up and pm_resume") Reported-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Tested-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org> Fixes: 8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets") Link: https://lore.kernel.org/r/1619048258-8717-2-git-send-email-khsieh@codeaurora.org Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In gen8_preallocate_top_level_pdp, pde and pde->pt.base are allocated
via alloc_pd(vm) with one reference. If pin_pt_dma() failed, pde->pt.base
is freed by i915_gem_object_put() with a reference dropped. Then free_pd
calls free_px() defined in intel_ppgtt.c, which calls i915_gem_object_put()
to put pde->pt.base again.
As pde->pt.base is protected by refcount, so the second put will not free
pde->pt.base actually. But, maybe it is better to remove the first put?
Fixes: 82adf901138cc ("drm/i915/gt: Shrink i915_page_directory's slab bucket") Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn> Reviewed-by: Matthew Auld <matthew.auld@intel.com> Signed-off-by: Matthew Auld <matthew.auld@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210426124340.4238-1-lyl2019@mail.ustc.edu.cn
(cherry picked from commit ac69496fe65cca0611d5917b7d232730ff605bc7) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
syzbot can trigger the WARN() in init_uevent_argv() which isn't the
nicest as the code does properly recover and handle the error. So
change the WARN() call to pr_warn() and provide some more information on
what the buffer size that was needed.
"usb: typec: tcpm: Address incorrect values of tcpm psy for pps supply"
introduced a regression for req_out_volt and req_op_curr calculation.
req_out_volt should consider the newly calculated max voltage instead
of previously accepted max voltage by the port partner. Likewise,
req_op_curr should consider the newly calculated max current instead
of previously accepted max current by the port partner.
Fixes: e3a072022487 ("usb: typec: tcpm: Address incorrect values of tcpm psy for pps supply") Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Badhri Jagan Sridharan <badhri@google.com> Link: https://lore.kernel.org/r/20210415050121.1928298-1-badhri@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
There is a timer wrap issue on dra7 for the ARM architected timer.
In a typical clock configuration the timer fails to wrap after 388 days.
To work around the issue, we need to use timer-ti-dm percpu timers instead.
Let's configure dmtimer3 and 4 as percpu timers by default, and warn about
the issue if the dtb is not configured properly.
Let's do this as a single patch so it can be backported to v5.8 and later
kernels easily. Note that this patch depends on earlier timer-ti-dm
systimer posted mode fixes, and a preparatory clockevent patch
"clocksource/drivers/timer-ti-dm: Prepare to handle dra7 timer wrap issue".
For more information, please see the errata for "AM572x Sitara Processors
Silicon Revisions 1.1, 2.0":
https://www.ti.com/lit/er/sprz429m/sprz429m.pdf
The concept is based on earlier reference patches done by Tero Kristo and
Keerthy.
Cc: Keerthy <j-keerthy@ti.com> Cc: Tero Kristo <kristo@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20210323074326.28302-3-tony@atomide.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
There is a timer wrap issue on dra7 for the ARM architected timer.
In a typical clock configuration the timer fails to wrap after 388 days.
To work around the issue, we need to use timer-ti-dm timers instead.
Let's prepare for adding support for percpu timers by adding a common
dmtimer_clkevt_init_common() and call it from dmtimer_clockevent_init().
This patch makes no intentional functional changes.
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20210323074326.28302-2-tony@atomide.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Remove the inline asm with a DIVU instruction from `__div64_32' and use
plain C code for the intended DIVMOD calculation instead. GCC is smart
enough to know that both the quotient and the remainder are calculated
with single DIVU, so with ISAs up to R5 the same instruction is actually
produced with overall similar code.
For R6 compiled code will work, but separate DIVU and MODU instructions
will be produced, which are also interlocked, so scalar implementations
will likely not perform as well as older ISAs with their asynchronous MD
unit. Likely still faster then the generic algorithm though.
This removes a compilation error for R6 however where the original DIVU
instruction is not supported anymore and the MDU accumulator registers
have been removed and consequently GCC complains as to a constraint it
cannot find a register for:
In file included from ./include/linux/math.h:5,
from ./include/linux/kernel.h:13,
from mm/page-writeback.c:15:
./include/linux/math64.h: In function 'div_u64_rem':
./arch/mips/include/asm/div64.h:76:17: error: inconsistent operand constraints in an 'asm'
76 | __asm__("divu $0, %z1, %z2" \
| ^~~~~~~
./include/asm-generic/div64.h:245:25: note: in expansion of macro '__div64_32'
245 | __rem = __div64_32(&(n), __base); \
| ^~~~~~~~~~
./include/linux/math64.h:91:22: note: in expansion of macro 'do_div'
91 | *remainder = do_div(dividend, divisor);
| ^~~~~~
This has passed correctness verification with test_div64 and reduced the
module's average execution time down to 1.0404s from 1.0445s with R3400
@40MHz. The module's MIPS I machine code has also shrunk by 12 bytes or
3 instructions.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We already check the high part of the divident against zero to avoid the
costly DIVU instruction in that case, needed to reduce the high part of
the divident, so we may well check against the divisor instead and set
the high part of the quotient to zero right away. We need to treat the
high part the divident in that case though as the remainder that would
be calculated by the DIVU instruction we avoided.
This has passed correctness verification with test_div64 and reduced the
module's average execution time down to 1.0445s and 0.2619s from 1.0668s
and 0.2629s respectively for an R3400 CPU @40MHz and a 5Kc CPU @160MHz.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Our current MIPS platform `__div64_32' handler is inactive, because it
is incorrectly only enabled for 64-bit configurations, for which generic
`do_div' code does not call it anyway.
The handler is not suitable for being called from there though as it
only calculates 32 bits of the quotient under the assumption the 64-bit
divident has been suitably reduced. Code for such reduction used to be
there, however it has been incorrectly removed with commit c21004cd5b4c
("MIPS: Rewrite <asm/div64.h> to work with gcc 4.4.0."), which should
have only updated an obsoleted constraint for an inline asm involving
$hi and $lo register outputs, while possibly wiring the original MIPS
variant of the `do_div' macro as `__div64_32' handler for the generic
`do_div' implementation
Correct the handler as follows then:
- Revert most of the commit referred, however retaining the current
formatting, except for the final two instructions of the inline asm
sequence, which the original commit missed. Omit the original 64-bit
parts though.
- Rename the original `do_div' macro to `__div64_32'. Use the combined
`x' constraint referring to the MD accumulator as a whole, replacing
the original individual `h' and `l' constraints used for $hi and $lo
registers respectively, of which `h' has been obsoleted with GCC 4.4.
Update surrounding code accordingly.
We have since removed support for GCC versions before 4.9, so no need
for a special arrangement here; GCC has supported the `x' constraint
since forever anyway, or at least going back to 1991.
- Rename the `__base' local variable in `__div64_32' to `__radix' to
avoid a conflict with a local variable in `do_div'.
- Actually enable this code for 32-bit rather than 64-bit configurations
by qualifying it with BITS_PER_LONG being 32 instead of 64. Include
<asm/bitsperlong.h> for this macro rather than <linux/types.h> as we
don't need anything else.
- Finally include <asm-generic/div64.h> last rather than first.
This has passed correctness verification with test_div64 and reduced the
module's average execution time down to 1.0668s and 0.2629s from 2.1529s
and 0.5647s respectively for an R3400 CPU @40MHz and a 5Kc CPU @160MHz.
For a reference 64-bit `do_div' code where we have the DDIVU instruction
available to do the whole calculation right away averages at 0.0660s for
the latter CPU.
Fixes: c21004cd5b4c ("MIPS: Rewrite <asm/div64.h> to work with gcc 4.4.0.") Reported-by: Huacai Chen <chenhuacai@kernel.org> Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Cc: stable@vger.kernel.org # v2.6.30+ Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
32-bit architectures which expect 8-byte alignment for 8-byte integers and
need 64-bit DMA addresses (arm, mips, ppc) had their struct page
inadvertently expanded in 2019. When the dma_addr_t was added, it forced
the alignment of the union to 8 bytes, which inserted a 4 byte gap between
'flags' and the union.
Fix this by storing the dma_addr_t in one or two adjacent unsigned longs.
This restores the alignment to that of an unsigned long. We always
store the low bits in the first word to prevent the PageTail bit from
being inadvertently set on a big endian platform. If that happened,
get_user_pages_fast() racing against a page which was freed and
reallocated to the page_pool could dereference a bogus compound_head(),
which would be hard to trace back to this cause.
Disable preemption when probing a user return MSR via RDSMR/WRMSR. If
the MSR holds a different value per logical CPU, the WRMSR could corrupt
the host's value if KVM is preempted between the RDMSR and WRMSR, and
then rescheduled on a different CPU.
Opportunistically land the helper in common x86, SVM will use the helper
in a future commit.
Fixes: 4be534102624 ("KVM: VMX: Initialize vmx->guest_msrs[] right after allocation") Cc: stable@vger.kernel.org Cc: Xiaoyao Li <xiaoyao.li@intel.com> Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210504171734.1434054-6-seanjc@google.com> Reviewed-by: Jim Mattson <jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Clear KVM's RDPID capability if the ENABLE_RDTSCP secondary exec control is
unsupported. Despite being enumerated in a separate CPUID flag, RDPID is
bundled under the same VMCS control as RDTSCP and will #UD in VMX non-root
if ENABLE_RDTSCP is not enabled.
Fixes: 41cd02c6f7f6 ("kvm: x86: Expose RDPID in KVM_GET_SUPPORTED_CPUID") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210504171734.1434054-2-seanjc@google.com> Reviewed-by: Jim Mattson <jmattson@google.com> Reviewed-by: Reiji Watanabe <reijiw@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When enlightened VMCS is in use and nested state is migrated with
vmx_get_nested_state()/vmx_set_nested_state() KVM can't map evmcs
page right away: evmcs gpa is not 'struct kvm_vmx_nested_state_hdr'
and we can't read it from VP assist page because userspace may decide
to restore HV_X64_MSR_VP_ASSIST_PAGE after restoring nested state
(and QEMU, for example, does exactly that). To make sure eVMCS is
mapped /vmx_set_nested_state() raises KVM_REQ_GET_NESTED_STATE_PAGES
request.
Commit f2c7ef3ba955 ("KVM: nSVM: cancel KVM_REQ_GET_NESTED_STATE_PAGES
on nested vmexit") added KVM_REQ_GET_NESTED_STATE_PAGES clearing to
nested_vmx_vmexit() to make sure MSR permission bitmap is not switched
when an immediate exit from L2 to L1 happens right after migration (caused
by a pending event, for example). Unfortunately, in the exact same
situation we still need to have eVMCS mapped so
nested_sync_vmcs12_to_shadow() reflects changes in VMCS12 to eVMCS.
As a band-aid, restore nested_get_evmcs_page() when clearing
KVM_REQ_GET_NESTED_STATE_PAGES in nested_vmx_vmexit(). The 'fix' is far
from being ideal as we can't easily propagate possible failures and even if
we could, this is most likely already too late to do so. The whole
'KVM_REQ_GET_NESTED_STATE_PAGES' idea for mapping eVMCS after migration
seems to be fragile as we diverge too much from the 'native' path when
vmptr loading happens on vmx_set_nested_state().
Fixes: f2c7ef3ba955 ("KVM: nSVM: cancel KVM_REQ_GET_NESTED_STATE_PAGES on nested vmexit") Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20210503150854.1144255-2-vkuznets@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Do not advertise emulation support for RDPID if RDTSCP is unsupported.
RDPID emulation subtly relies on MSR_TSC_AUX to exist in hardware, as
both vmx_get_msr() and svm_get_msr() will return an error if the MSR is
unsupported, i.e. ctxt->ops->get_msr() will fail and the emulator will
inject a #UD.
Note, RDPID emulation also relies on RDTSCP being enabled in the guest,
but this is a KVM bug and will eventually be fixed.
Fixes: fb6d4d340e05 ("KVM: x86: emulate RDPID") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210504171734.1434054-3-seanjc@google.com> Reviewed-by: Jim Mattson <jmattson@google.com> Reviewed-by: Reiji Watanabe <reijiw@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit d3eeb1d77c5d0af ("xen/gntdev: use mmu_interval_notifier_insert")
introduced an error in gntdev_mmap(): in case the call of
mmu_interval_notifier_insert_locked() fails the exit path should not
call mmu_interval_notifier_remove(), as this might result in NULL
dereferences.
One reason for failure is e.g. a signal pending for the running
process.
Fixes: d3eeb1d77c5d0af ("xen/gntdev: use mmu_interval_notifier_insert") Cc: stable@vger.kernel.org Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Luca Fancellu <luca.fancellu@arm.com> Link: https://lore.kernel.org/r/20210423054038.26696-1-jgross@suse.com Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We have a cycle of callbacks scheduling works which submit
URBs with those callbacks. This needs to be blocked, stopped
and unblocked to untangle the circle.
Signed-off-by: Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/20210426092622.20433-1-oneukum@suse.com Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The raw temperature value is a 16-bit signed integer. The sign casting
is missing in the code, which results in a wrong temperature reported
by userspace tools, fix it.
Cc: stable@vger.kernel.org Fixes: 3904b28efb2c ("iio: gyro: Add driver for the MPU-3050 gyroscope")
Datasheet: https://www.cdiweb.com/datasheets/invensense/mpu-3000a.pdf Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Asus TF201 Reported-by: Svyatoslav Ryhel <clamor95@gmail.com> Reviewed-by: Andy Shevchenko <Andy.Shevchenko@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com> Link: https://lore.kernel.org/r/20210423020959.5023-1-digetx@gmail.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently ioctl handlers are removed twice. For the first time during
iio_device_unregister() then later on inside
iio_device_unregister_eventset() and iio_buffers_free_sysfs_and_mask().
Double free leads to kernel panic.
Fix this by not touching ioctl handlers list directly but rather
letting code responsible for registration call the matching cleanup
routine itself.
Fixes: 8dedcc3eee3ac ("iio: core: centralize ioctl() calls to the main chardev") Signed-off-by: Tomasz Duszynski <tomasz.duszynski@octakon.com> Acked-by: Alexandru Ardelean <ardeleanalex@gmail.com> Cc: <Stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210423080244.2790-1-tomasz.duszynski@octakon.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
One of AMD xhci controller require reset on resume.
Occasionally AMD xhci controller does not respond to
Stop endpoint command.
Once the issue happens controller goes into bad state
and in that case controller needs to be reset.
'xhci_urb_enqueue()' is passed a 'mem_flags' argument, because "URBs may be
submitted in interrupt context" (see comment related to 'usb_submit_urb()'
in 'drivers/usb/core/urb.c')
So this flag should be used in all the calling chain.
Up to now, 'xhci_check_maxpacket()' which is only called from
'xhci_urb_enqueue()', uses GFP_KERNEL.
Be safe and pass the mem_flags to this function as well.
Fixes: ddba5cd0aeff ("xhci: Use command structures when queuing commands on the command ring") Cc: <stable@vger.kernel.org> Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20210512080816.866037-4-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In the same way as Intel Tiger Lake TCSS (Type-C Subsystem) the Alder Lake
TCSS xHCI needs to be runtime suspended whenever possible to allow the
TCSS hardware block to enter D3cold and thus save energy.
commit 4dbc6a4ef06d ("usb: typec: ucsi: save power data objects
in PD mode") introduced retrieval of the PDOs when connected to a
PD-capable source. But only the first 4 PDOs are received since
that is the maximum number that can be fetched at a time given the
MESSAGE_IN length limitation (16 bytes). However, as per the PD spec
a connected source may advertise up to a maximum of 7 PDOs.
If such a source is connected it's possible the PPM could have
negotiated a power contract with one of the PDOs at index greater
than 4, and would be reflected in the request data object's (RDO)
object position field. This would result in an out-of-bounds access
when the rdo_index() is used to index into the src_pdos array in
ucsi_psy_get_voltage_now().
With the help of the UBSAN -fsanitize=array-bounds checker enabled
this exact issue is revealed when connecting to a PD source adapter
that advertise 5 PDOs and the PPM enters a contract having selected
the 5th one.
We can resolve this by instead retrieving and storing up to the
maximum of 7 PDOs in the con->src_pdos array. This would involve
two calls to the GET_PDOS command.
Fixes: 992a60ed0d5e ("usb: typec: ucsi: register with power_supply class") Fixes: 4dbc6a4ef06d ("usb: typec: ucsi: save power data objects in PD mode") Cc: stable@vger.kernel.org Reported-and-tested-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Jack Pham <jackp@codeaurora.org> Link: https://lore.kernel.org/r/20210503074611.30973-1-jackp@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If an error is received when issuing a start or update transfer
command, the error handler will stop all active requests (including
the current USB request), and call dwc3_gadget_giveback() to notify
function drivers of the requests which have been stopped. Avoid
returning an error for kick transfer during EP queue, to remove
duplicate cleanup operations on the request being queued.
commit 72704f876f50 ("dwc3: gadget: Implement the suspend entry event
handler") introduced (nearly 5 years ago!) an interrupt handler for
U3/L1-L2 suspend events. The problem is that these events aren't
currently enabled in the DEVTEN register so the handler is never
even invoked. Fix this simply by enabling the corresponding bit
in dwc3_gadget_enable_irq() using the same revision check as found
in the handler.
Fixes: 72704f876f50 ("dwc3: gadget: Implement the suspend entry event handler") Acked-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Jack Pham <jackp@codeaurora.org> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210428090111.3370-1-jackp@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This may happen if the port becomes resume status exactly
when usb_port_resume() gets port status, it still need provide
a TRSMCRY time before access the device.
CC: <stable@vger.kernel.org> Reported-by: Tianping Fang <tianping.fang@mediatek.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Link: https://lore.kernel.org/r/20210512020738.52961-1-chunfeng.yun@mediatek.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The dwc2 gadget support maps and unmaps DMA buffers as necessary. When
mapping and unmapping it uses the direction of the endpoint to select
the direction of the DMA transfer, but this fails for Control OUT
transfers because the unmap occurs after the endpoint direction has
been reversed for the status phase.
A possible solution would be to unmap the buffer before the direction
is changed, but a safer, less invasive fix is to remember the buffer
direction independently of the endpoint direction.
Fixes: fe0b94abcdf6 ("usb: dwc2: gadget: manage ep0 state in software") Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Phil Elwell <phil@raspberrypi.com> Link: https://lore.kernel.org/r/20210506112200.2893922-1-phil@raspberrypi.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
On some devices (specifically the SC8180x based Surface Pro X with
QCOM04A6) HC halt / xhci_halt() times out during boot. Manually binding
the xhci-hcd driver at some point later does not exhibit this behavior.
To work around this, double XHCI_MAX_HALT_USEC, which also resolves this
issue.
Cc: <stable@vger.kernel.org> Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20210512080816.866037-5-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When extcon is used in combination with dwc3, it is assumed that the dwc3
registers are untouched and as such are only configured if VBUS is valid
or ID is tied to ground.
In case VBUS is not valid or ID is floating, the registers are not
configured as such during driver initialization, causing a wrong
default state during boot.
If the registers are not in a default state, because they are for
instance touched by a boot loader, this can cause for a kernel error.
If a tag set is shared across request queues (e.g. SCSI LUNs) then the
block layer core keeps track of the number of active request queues in
tags->active_queues. blk_mq_tag_busy() and blk_mq_tag_idle() update that
atomic counter if the hctx flag BLK_MQ_F_TAG_QUEUE_SHARED is set. Make
sure that blk_mq_exit_queue() calls blk_mq_tag_idle() before that flag is
cleared by blk_mq_del_queue_tag_set().
Cc: Christoph Hellwig <hch@infradead.org> Cc: Ming Lei <ming.lei@redhat.com> Cc: Hannes Reinecke <hare@suse.com> Fixes: 0d2602ca30e4 ("blk-mq: improve support for shared tags maps") Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Ming Lei <ming.lei@redhat.com> Link: https://lore.kernel.org/r/20210513171529.7977-1-bvanassche@acm.org Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In case of shared sbitmap, request won't be held in plug list any more
sine commit 32bc15afed04 ("blk-mq: Facilitate a shared sbitmap per
tagset"), this way makes request merge from flush plug list & batching
submission not possible, so cause performance regression.
Yanhui reports performance regression when running sequential IO
test(libaio, 16 jobs, 8 depth for each job) in VM, and the VM disk
is emulated with image stored on xfs/megaraid_sas.
Fix the issue by recovering original behavior to allow to hold request
in plug list.
Cc: Yanhui Ma <yama@redhat.com> Cc: John Garry <john.garry@huawei.com> Cc: Bart Van Assche <bvanassche@acm.org> Cc: kashyap.desai@broadcom.com Fixes: 32bc15afed04 ("blk-mq: Facilitate a shared sbitmap per tagset") Signed-off-by: Ming Lei <ming.lei@redhat.com> Link: https://lore.kernel.org/r/20210514022052.1047665-1-ming.lei@redhat.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Open /dev/nbdX first, the config_refs will be 1 and
the pointers in nbd_device are still null. Disconnect
/dev/nbdX, then reference a null recv_workq. The
protection by config_refs in nbd_genl_disconnect is useless.
To fix it, just add if (nbd->recv_workq) to nbd_disconnect_and_put().
Fixes: e9e006f5fcf2 ("nbd: fix max number of supported devs") Signed-off-by: Sun Ke <sunke32@huawei.com> Reviewed-by: Josef Bacik <josef@toxicpanda.com> Link: https://lore.kernel.org/r/20210512114331.1233964-2-sunke32@huawei.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In f2fs_destroy_compress_ctx(), after f2fs_destroy_compress_ctx(),
cc.cluster_idx will be cleared w/ NULL_CLUSTER, f2fs_cluster_blocks()
may check wrong cluster metadata, fix it.
Fixes: 4c8ff7095bef ("f2fs: support data compression") Signed-off-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The root cause is truncate() may race with overwrite as below,
so that one reference count left in page can not guarantee the
page attaching in mapping tree all the time, after truncation,
later find_lock_page() may return NULL pointer.
When running some traffic and taking down the link on peer, a
retry counter exceeded error is received. This leads to
nvmet_rdma_error_comp which tried accessing the cq_context to
obtain the queue. The cq_context is no longer valid after the
fix to use shared CQ mechanism and should be obtained similar
to how it is obtained in other functions from the wc->qp.
When handling passthru commands, for inline bio allocation we only
consider the transfer size. This works well when req->sg_cnt fits into
the req->inline_bvec, but it will result in the early return from
bio_add_hw_page() when req->sg_cnt > NVMET_MAX_INLINE_BVEC.
Consider an I/O of size 32768 and first buffer is not aligned to the
page boundary, then I/O is split in following manner :-
Now the req->transfer_size == NVMET_MAX_INLINE_DATA_LEN i.e. 32768, but
the req->sg_cnt is (9) > NVMET_MAX_INLINE_BIOVEC which is (8).
This will result in early return in the following code path :-
nvmet_bdev_execute_rw()
bio_add_pc_page()
bio_add_hw_page()
if (bio_full(bio, len))
return 0;
Use previously introduced helper nvmet_use_inline_bvec() to consider
req->sg_cnt when using inline bio. This only affects nvme-loop
transport.
Fixes: dab3902b19a0 ("nvmet: use inline bio for passthru fast path") Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When handling rw commands, for inline bio case we only consider
transfer size. This works well when req->sg_cnt fits into the
req->inline_bvec, but it will result in the warning in
__bio_add_page() when req->sg_cnt > NVMET_MAX_INLINE_BVEC.
Consider an I/O size 32768 and first page is not aligned to the page
boundary, then I/O is split in following manner :-
Now the req->transfer_size == NVMET_MAX_INLINE_DATA_LEN i.e. 32768, but
the req->sg_cnt is (9) > NVMET_MAX_INLINE_BIOVEC which is (8).
This will result in the following warning message :-
This scenario is very hard to reproduce on the nvme-loop transport only
with rw commands issued with the passthru IOCTL interface from the host
application and the data buffer is allocated with the malloc() and not
the posix_memalign().
Fixes: 73383adfad24 ("nvmet: don't split large I/Os unconditionally") Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In this preparation patch, we add helpers to convert lbas to sectors &
sectors to lba. This is needed to eliminate code duplication in the ZBD
backend.
Use these helpers in the block device backend.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
__blk_mq_sched_bio_merge() gets the ctx and hctx for the current CPU and
passes the hctx to ->bio_merge(). kyber_bio_merge() then gets the ctx
for the current CPU again and uses that to get the corresponding Kyber
context in the passed hctx. However, the thread may be preempted between
the two calls to blk_mq_get_ctx(), and the ctx returned the second time
may no longer correspond to the passed hctx. This "works" accidentally
most of the time, but it can cause us to read garbage if the second ctx
came from an hctx with more ctx's than the first one (i.e., if
ctx->index_hw[hctx->type] > hctx->nr_ctx).
This manifested as this UBSAN array index out of bounds error reported
by Jakub:
UBSAN: array-index-out-of-bounds in ../kernel/locking/qspinlock.c:130:9
index 13106 is out of range for type 'long unsigned int [128]'
Call Trace:
dump_stack+0xa4/0xe5
ubsan_epilogue+0x5/0x40
__ubsan_handle_out_of_bounds.cold.13+0x2a/0x34
queued_spin_lock_slowpath+0x476/0x480
do_raw_spin_lock+0x1c2/0x1d0
kyber_bio_merge+0x112/0x180
blk_mq_submit_bio+0x1f5/0x1100
submit_bio_noacct+0x7b0/0x870
submit_bio+0xc2/0x3a0
btrfs_map_bio+0x4f0/0x9d0
btrfs_submit_data_bio+0x24e/0x310
submit_one_bio+0x7f/0xb0
submit_extent_page+0xc4/0x440
__extent_writepage_io+0x2b8/0x5e0
__extent_writepage+0x28d/0x6e0
extent_write_cache_pages+0x4d7/0x7a0
extent_writepages+0xa2/0x110
do_writepages+0x8f/0x180
__writeback_single_inode+0x99/0x7f0
writeback_sb_inodes+0x34e/0x790
__writeback_inodes_wb+0x9e/0x120
wb_writeback+0x4d2/0x660
wb_workfn+0x64d/0xa10
process_one_work+0x53a/0xa80
worker_thread+0x69/0x5b0
kthread+0x20b/0x240
ret_from_fork+0x1f/0x30
Only Kyber uses the hctx, so fix it by passing the request_queue to
->bio_merge() instead. BFQ and mq-deadline just use that, and Kyber can
map the queues itself to avoid the mismatch.
Fixes: a6088845c2bf ("block: kyber: make kyber more friendly with merging") Reported-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Omar Sandoval <osandov@fb.com> Link: https://lore.kernel.org/r/c7598605401a48d5cfeadebb678abd10af22b83f.1620691329.git.osandov@fb.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If 'acpi_device_set_name()' fails, we must free
'acpi_device_bus_id->bus_id' or there is a (potential) memory leak.
Fixes: eb50aaf960e3 ("ACPI: scan: Use unique number for instance_no") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The poll rate limiter time was initialized at zero. This breaks the
comparison in time_after if jiffies is large. Switch to storing the
next update time rather than the previous time, and initialize the
time when the device is probed.
Fixes: c10e753d43eb ("hwmon (occ): Add sensor types and versions") Signed-off-by: Eddie James <eajames@linux.ibm.com> Link: https://lore.kernel.org/r/20210429151336.18980-1-eajames@linux.ibm.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
'retval' is known to be -ENODEV here.
This is a hard-coded default error code which is not useful in the error
message. Moreover, another error message is printed at the end of the
error handling path. The corresponding error code (-ENOMEM) is more
informative.
So remove simplify the first error message.
While at it, also remove the useless initialization of 'retval'.
When the ioctl() mechanism was introduced in IIO core to centralize the
registration of all ioctls in one place via commit 8dedcc3eee3ac ("iio:
core: centralize ioctl() calls to the main chardev"), the return code was
changed from ENODEV to EINVAL, when the ioctl code isn't known.
This was done by accident.
This change reverts back to the old behavior, where if the ioctl() code
isn't known, ENODEV is returned (vs EINVAL).
This was brought into perspective by this patch:
https://lore.kernel.org/linux-iio/20210428150815.136150-1-paul@crapouillou.net/
Fixes: 8dedcc3eee3ac ("iio: core: centralize ioctl() calls to the main chardev") Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com> Reviewed-by: Nuno Sá <nuno.sa@analog.com> Tested-by: Paul Cercueil <paul@crapouillou.net> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
During commit 067fda1c065ff ("iio: hid-sensors: move triggered buffer
setup into hid_sensor_setup_trigger"), the
iio_triggered_buffer_{setup,cleanup}() functions got moved under the
hid-sensor-trigger module.
The above change works fine, if any of the sensors get built. However, when
only the common hid-sensor-trigger module gets built (and none of the
drivers), then the IIO_TRIGGERED_BUFFER symbol isn't selected/enforced.
Previously, each driver would enforce/select the IIO_TRIGGERED_BUFFER
symbol. With this change the HID_SENSOR_IIO_TRIGGER (for the
hid-sensor-trigger module) will enforce that IIO_TRIGGERED_BUFFER gets
selected.
All HID sensor drivers select the HID_SENSOR_IIO_TRIGGER symbol. So, this
change removes the IIO_TRIGGERED_BUFFER enforcement from each driver.
Fixes: 067fda1c065ff ("iio: hid-sensors: move triggered buffer setup into hid_sensor_setup_trigger") Reported-by: Thomas Deutschmann <whissi@gentoo.org> Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com> Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Link: https://lore.kernel.org/r/20210414084955.260117-1-aardelean@deviqon.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When devm_request_threaded_irq() fails, we should decrease the
runtime PM counter to keep the counter balanced. But when
iio_device_register() fails, we need not to decrease it because
we have already decreased it before.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Fixes: 97d642e23037 ("iio: light: Add a driver for Sharp GP2AP002x00F") Link: https://lore.kernel.org/r/20210407034927.16882-1-dinghao.liu@zju.edu.cn Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
As part of commit e81a7018d93a ("usb: dwc3: allocate gadget structure
dynamically") the dwc3_gadget_release() was added which will free
the dwc->gadget structure upon the device's removal when
usb_del_gadget_udc() is called in dwc3_gadget_exit().
However, simply freeing the gadget results a dangling pointer
situation: the endpoints created in dwc3_gadget_init_endpoints()
have their dep->endpoint.ep_list members chained off the list_head
anchored at dwc->gadget->ep_list. Thus when dwc->gadget is freed,
the first dwc3_ep in the list now has a dangling prev pointer and
likewise for the next pointer of the dwc3_ep at the tail of the list.
The dwc3_gadget_free_endpoints() that follows will result in a
use-after-free when it calls list_del().
This was caught by enabling KASAN and performing a driver unbind.
The recent commit 568262bf5492 ("usb: dwc3: core: Add shutdown
callback for dwc3") also exposes this as a panic during shutdown.
There are a few possibilities to fix this. One could be to perform
a list_del() of the gadget->ep_list itself which removes it from
the rest of the dwc3_ep chain.
Another approach is what this patch does, by splitting up the
usb_del_gadget_udc() call into its separate "del" and "put"
components. This allows dwc3_gadget_free_endpoints() to be
called before the gadget is finally freed with usb_put_gadget().
Fixes: e81a7018d93a ("usb: dwc3: allocate gadget structure dynamically") Reviewed-by: Peter Chen <peter.chen@kernel.org> Signed-off-by: Jack Pham <jackp@codeaurora.org> Link: https://lore.kernel.org/r/20210501093558.7375-1-jackp@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Fixes: eee19501926d ("perf tools: Grab a copy of libbpf's hashmap") Reported-by: Justin M. Forbes <jforbes@redhat.com> Signed-off-by: Jiri Olsa <jolsa@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Petlan <mpetlan@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/20210508205020.617984-1-jolsa@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
I am seeing missed wakeups which ultimately lead to a deadlock when I am
using virtiofs with DAX enabled and running "make -j". I had to mount
virtiofs as rootfs and also reduce to dax window size to 256M to reproduce
the problem consistently.
So here is the problem. put_unlocked_entry() wakes up waiters only
if entry is not null as well as !dax_is_conflict(entry). But if I
call multiple instances of invalidate_inode_pages2() in parallel,
then I can run into a situation where there are waiters on
this index but nobody will wake these waiters.
Say a fault in in progress and it has locked entry at offset say "0x1c".
Now say three instances of invalidate_inode_pages2() are in progress
(A, B, C) and they all try to invalidate entry at offset "0x1c". Given
dax entry is locked, all tree instances A, B, C will wait in wait queue.
When dax fault finishes, say A is woken up. It will store NULL entry
at index "0x1c" and wake up B. When B comes along it will find "entry=0"
at page offset 0x1c and it will call put_unlocked_entry(&xas, 0). And
this means put_unlocked_entry() will not wake up next waiter, given
the current code. And that means C continues to wait and is not woken
up.
This patch fixes the issue by waking up all waiters when a dax entry
has been invalidated. This seems to fix the deadlock I am facing
and I can make forward progress.
Reported-by: Sergio Lopez <slp@redhat.com> Fixes: ac401cc78242 ("dax: New fault locking") Reviewed-by: Jan Kara <jack@suse.cz> Suggested-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Vivek Goyal <vgoyal@redhat.com> Link: https://lore.kernel.org/r/20210428190314.1865312-4-vgoyal@redhat.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
As of now put_unlocked_entry() always wakes up next waiter. In next
patches we want to wake up all waiters at one callsite. Hence, add a
parameter to the function.
This patch does not introduce any change of behavior.
Reviewed-by: Greg Kurz <groug@kaod.org> Reviewed-by: Jan Kara <jack@suse.cz> Suggested-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Vivek Goyal <vgoyal@redhat.com> Link: https://lore.kernel.org/r/20210428190314.1865312-3-vgoyal@redhat.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Dan mentioned that he is not very fond of passing around a boolean true/false
to specify if only next waiter should be woken up or all waiters should be
woken up. He instead prefers that we introduce an enum and make it very
explicity at the callsite itself. Easier to read code.
This patch should not introduce any change of behavior.
Reviewed-by: Greg Kurz <groug@kaod.org> Reviewed-by: Jan Kara <jack@suse.cz> Suggested-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Vivek Goyal <vgoyal@redhat.com> Link: https://lore.kernel.org/r/20210428190314.1865312-2-vgoyal@redhat.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Initialize audio_comp when audio starts and wait for audio_comp at
dp_display_disable(). This will take care of both dongle unplugged
and display off (suspend) cases.
Changes in v2:
-- add dp_display_signal_audio_start()
Changes in v3:
-- restore dp_display_handle_plugged_change() at dp_hpd_unplug_handle().
Changes in v4:
-- none
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Tested-by: Stephen Boyd <swboyd@chromium.org> Fixes: c703d5789590 ("drm/msm/dp: trigger unplug event in msm_dp_display_disable") Link: https://lore.kernel.org/r/1619048258-8717-3-git-send-email-khsieh@codeaurora.org Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit ee66e453db13d (KVM: lapic: Busy wait for timer to expire when
using hv_timer) tries to set ktime->expired_tscdeadline by checking
ktime->hv_timer_in_use since lapic timer oneshot/periodic modes which
are emulated by vmx preemption timer also get advanced, they leverage
the same vmx preemption timer logic with tsc-deadline mode. However,
ktime->hv_timer_in_use is cleared before apic_timer_expired() handling,
let's delay this clearing in preemption-disabled region.
Fixes: ee66e453db13d ("KVM: lapic: Busy wait for timer to expire when using hv_timer") Reviewed-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Message-Id: <1619608082-4187-1-git-send-email-wanpengli@tencent.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
mmu500 targets don't have a "cx_mem" region, set llc_mmio to NULL in that
case to avoid the IS_ERR() condition in a6xx_llc_activate().
Fixes: 3d247123b5a1 ("drm/msm/a6xx: Add support for using system cache on MMU500 based targets") Signed-off-by: Jonathan Marek <jonathan@marek.ca> Link: https://lore.kernel.org/r/20210424014927.1661-1-jonathan@marek.ca Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
single_task_running() is usually more general than need_resched()
but CFS_BANDWIDTH throttling will use resched_task() when there
is just one task to get the task to block. This was causing
long-need_resched warnings and was likely allowing VMs to
overrun their quota when halt polling.
Signed-off-by: Ben Segall <bsegall@google.com> Signed-off-by: Venkatesh Srinivas <venkateshs@chromium.org>
Message-Id: <20210429162233.116849-1-venkateshs@chromium.org> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Cc: stable@vger.kernel.org Reviewed-by: Jim Mattson <jmattson@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Gen2 tiles are 2KiB in size so i915_gem_object_get_tile_row_size()
can in fact return <4KiB, which leads to div-by-zero here.
Avoid that.
Not sure i915_gem_object_get_tile_row_size() is entirely
sane anyway since it doesn't account for the different tile
layouts on i8xx/i915...
I'm not able to hit this before commit 6846895fde05 ("drm/i915:
Replace PIN_NONFAULT with calls to PIN_NOEVICT") and it looks
like I also need to run recent version of Mesa. With those in
place xonotic trips on this quite easily on my 85x.
It is stored in dynamically allocated memory, so sysfs_bin_attr_init() must
be called to initialize it. (Note: "initialization" only sets the .attr.key
member in this struct; it does not change the value of any other members.)
Otherwise, when CONFIG_DEBUG_LOCK_ALLOC=y this message appears during boot:
When doing a fast fsync on a file, there is a race which can result in the
fsync returning success to user space without logging the inode and without
durably persisting new data.
The following example shows one possible scenario for this:
# Now we have:
# file bar == inode 257
# file baz == inode 258
$ mv /mnt/baz /mnt/foo
# Now we have:
# file bar == inode 257
# file foo == inode 258
$ xfs_io -c "pwrite -S 0xcd 0 1M" /mnt/foo
# fsync bar before foo, it is important to trigger the race.
$ xfs_io -c "fsync" /mnt/bar
$ xfs_io -c "fsync" /mnt/foo
# After this:
# inode 257, file bar, is empty
# inode 258, file foo, has 1M filled with 0xcd
<power failure>
# Replay the log:
$ mount /dev/sdc /mnt
# After this point file foo should have 1M filled with 0xcd and not 0xab
The following steps explain how the race happens:
1) Before the first fsync of inode 258, when it has the "baz" name, its
->logged_trans is 0, ->last_sub_trans is 0 and ->last_log_commit is -1.
The inode also has the full sync flag set;
2) After the first fsync, we set inode 258 ->logged_trans to 6, which is
the generation of the current transaction, and set ->last_log_commit
to 0, which is the current value of ->last_sub_trans (done at
btrfs_log_inode()).
The full sync flag is cleared from the inode during the fsync.
The log sub transaction that was committed had an ID of 0 and when we
synced the log, at btrfs_sync_log(), we incremented root->log_transid
from 0 to 1;
3) During the rename:
We update inode 258, through btrfs_update_inode(), and that causes its
->last_sub_trans to be set to 1 (the current log transaction ID), and
->last_log_commit remains with a value of 0.
After updating inode 258, because we have previously logged the inode
in the previous fsync, we log again the inode through the call to
btrfs_log_new_name(). This results in updating the inode's
->last_log_commit from 0 to 1 (the current value of its
->last_sub_trans).
The ->last_sub_trans of inode 257 is updated to 1, which is the ID of
the next log transaction;
4) Then a buffered write against inode 258 is made. This leaves the value
of ->last_sub_trans as 1 (the ID of the current log transaction, stored
at root->log_transid);
5) Then an fsync against inode 257 (or any other inode other than 258),
happens. This results in committing the log transaction with ID 1,
which results in updating root->last_log_commit to 1 and bumping
root->log_transid from 1 to 2;
6) Then an fsync against inode 258 starts. We flush delalloc and wait only
for writeback to complete, since the full sync flag is not set in the
inode's runtime flags - we do not wait for ordered extents to complete.
Then, at btrfs_sync_file(), we call btrfs_inode_in_log() before the
ordered extent completes. The call returns true:
static inline bool btrfs_inode_in_log(...)
{
bool ret = false;
spin_lock(&inode->lock);
if (inode->logged_trans == generation &&
inode->last_sub_trans <= inode->last_log_commit &&
inode->last_sub_trans <= inode->root->last_log_commit)
ret = true;
spin_unlock(&inode->lock);
return ret;
}
generation has a value of 6 (fs_info->generation), ->logged_trans also
has a value of 6 (set when we logged the inode during the first fsync
and when logging it during the rename), ->last_sub_trans has a value
of 1, set during the rename (step 3), ->last_log_commit also has a
value of 1 (set in step 3) and root->last_log_commit has a value of 1,
which was set in step 5 when fsyncing inode 257.
As a consequence we don't log the inode, any new extents and do not
sync the log, resulting in a data loss if a power failure happens
after the fsync and before the current transaction commits.
Also, because we do not log the inode, after a power failure the mtime
and ctime of the inode do not match those we had before.
When the ordered extent completes before we call btrfs_inode_in_log(),
then the call returns false and we log the inode and sync the log,
since at the end of ordered extent completion we update the inode and
set ->last_sub_trans to 2 (the value of root->log_transid) and
->last_log_commit to 1.
This problem is found after removing the check for the emptiness of the
inode's list of modified extents in the recent commit 209ecbb8585bf6
("btrfs: remove stale comment and logic from btrfs_inode_in_log()"),
added in the 5.13 merge window. However checking the emptiness of the
list is not really the way to solve this problem, and was never intended
to, because while that solves the problem for COW writes, the problem
persists for NOCOW writes because in that case the list is always empty.
In the case of NOCOW writes, even though we wait for the writeback to
complete before returning from btrfs_sync_file(), we end up not logging
the inode, which has a new mtime/ctime, and because we don't sync the log,
we never issue disk barriers (send REQ_PREFLUSH to the device) since that
only happens when we sync the log (when we write super blocks at
btrfs_sync_log()). So effectively, for a NOCOW case, when we return from
btrfs_sync_file() to user space, we are not guaranteeing that the data is
durably persisted on disk.
Also, while the example above uses a rename exchange to show how the
problem happens, it is not the only way to trigger it. An alternative
could be adding a new hard link to inode 258, since that also results
in calling btrfs_log_new_name() and updating the inode in the log.
An example reproducer using the addition of a hard link instead of a
rename operation:
# After this point file foo often has 1M filled with 0xab and not 0xcd
The reasons leading to the final fsync of file foo, inode 258, not
persisting the new data are the same as for the previous example with
a rename operation.
So fix by never skipping logging and log syncing when there are still any
ordered extents in flight. To avoid making the conditional if statement
that checks if logging an inode is needed harder to read, place all the
logic into an helper function with separate if statements to make it more
manageable and easier to read.
A test case for fstests will follow soon.
For NOCOW writes, the problem existed before commit b5e6c3e170b770
("btrfs: always wait on ordered extents at fsync time"), introduced in
kernel 4.19, then it went away with that commit since we started to always
wait for ordered extent completion before logging.
The problem came back again once the fast fsync path was changed again to
avoid waiting for ordered extent completion, in commit 487781796d3022
("btrfs: make fast fsyncs wait only for writeback"), added in kernel 5.10.
However, for COW writes, the race only happens after the recent
commit 209ecbb8585bf6 ("btrfs: remove stale comment and logic from
btrfs_inode_in_log()"), introduced in the 5.13 merge window. For NOCOW
writes, the bug existed before that commit. So tag 5.10+ as the release
for stable backports.
CC: stable@vger.kernel.org # 5.10+ Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
There are a few exceptional cases where cloning an inline extent needs to
copy the inline extent data into a page of the destination inode.
When this happens, we end up starting a transaction while having a dirty
page for the destination inode and while having the range locked in the
destination's inode iotree too. Because when reserving metadata space
for a transaction we may need to flush existing delalloc in case there is
not enough free space, we have a mechanism in place to prevent a deadlock,
which was introduced in commit 3d45f221ce627d ("btrfs: fix deadlock when
cloning inline extent and low on free metadata space").
However when using qgroups, a transaction also reserves metadata qgroup
space, which can also result in flushing delalloc in case there is not
enough available space at the moment. When this happens we deadlock, since
flushing delalloc requires locking the file range in the inode's iotree
and the range was already locked at the very beginning of the clone
operation, before attempting to start the transaction.
When this issue happens, stack traces like the following are reported:
So fix this by skipping the flush of delalloc for an inode that is
flagged with BTRFS_INODE_NO_DELALLOC_FLUSH, meaning it is currently under
such a special case of cloning an inline extent, when flushing delalloc
during qgroup metadata reservation.
The special cases for cloning inline extents were added in kernel 5.7 by
by commit 05a5a7621ce66c ("Btrfs: implement full reflink support for
inline extents"), while having qgroup metadata space reservation flushing
delalloc when low on space was added in kernel 5.9 by commit c53e9653605dbf ("btrfs: qgroup: try to flush qgroup space when we get
-EDQUOT"). So use a "Fixes:" tag for the later commit to ease stable
kernel backports.
Reported-by: Wang Yugui <wangyugui@e16-tech.com> Link: https://lore.kernel.org/linux-btrfs/20210421083137.31E3.409509F4@e16-tech.com/ Fixes: c53e9653605dbf ("btrfs: qgroup: try to flush qgroup space when we get -EDQUOT") CC: stable@vger.kernel.org # 5.9+ Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
To ensure that instructions are observable in a new mapping, the arm64
set_pte_at() implementation cleans the D-cache and invalidates the
I-cache to the PoU. As an optimisation, this is only done on executable
mappings and the PG_dcache_clean page flag is set to avoid future cache
maintenance on the same page.
When two different processes map the same page (e.g. private executable
file or shared mapping) there's a potential race on checking and setting
PG_dcache_clean via set_pte_at() -> __sync_icache_dcache(). While on the
fault paths the page is locked (PG_locked), mprotect() does not take the
page lock. The result is that one process may see the PG_dcache_clean
flag set but the I/D cache maintenance not yet performed.
Avoid test_and_set_bit(PG_dcache_clean) in favour of separate test_bit()
and set_bit(). In the rare event of a race, the cache maintenance is
done twice.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Cc: <stable@vger.kernel.org> Cc: Will Deacon <will@kernel.org> Cc: Steven Price <steven.price@arm.com> Reviewed-by: Steven Price <steven.price@arm.com> Acked-by: Will Deacon <will@kernel.org> Link: https://lore.kernel.org/r/20210514095001.13236-1-catalin.marinas@arm.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
A valid implementation choice for the ChooseRandomNonExcludedTag()
pseudocode function used by IRG is to behave in the same way as with
GCR_EL1.RRND=0. This would mean that RGSR_EL1.SEED is used as an LFSR
which must have a non-zero value in order for IRG to properly produce
pseudorandom numbers. However, RGSR_EL1 is reset to an UNKNOWN value
on soft reset and thus may reset to 0. Therefore we must initialize
RGSR_EL1.SEED to a non-zero value in order to ensure that IRG behaves
as expected.
Signed-off-by: Peter Collingbourne <pcc@google.com> Fixes: 3b714d24ef17 ("arm64: mte: CPU feature detection and initial sysreg configuration") Cc: <stable@vger.kernel.org> # 5.10 Link: https://linux-review.googlesource.com/id/I2b089b6c7d6f17ee37e2f0db7df5ad5bcc04526c Acked-by: Mark Rutland <mark.rutland@arm.com> Link: https://lore.kernel.org/r/20210507185905.1745402-1-pcc@google.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Some AMD Ryzen generations has different calculation method on maximum
performance. 255 is not for all ASICs, some specific generations should use 166
as the maximum performance. Otherwise, it will report incorrect frequency value
like below:
~ → lscpu | grep MHz
CPU MHz: 3400.000
CPU max MHz: 7228.3198
CPU min MHz: 2200.0000
[ mingo: Tidied up whitespace use. ]
[ Alexander Monakov <amonakov@ispras.ru>: fix 225 -> 255 typo. ]
Fixes: 41ea667227ba ("x86, sched: Calculate frequency invariance for AMD systems") Fixes: 3c55e94c0ade ("cpufreq: ACPI: Extend frequency tables to cover boost frequencies") Reported-by: Jason Bagavatsingham <jason.bagavatsingham@gmail.com> Fixed-by: Alexander Monakov <amonakov@ispras.ru> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Ingo Molnar <mingo@kernel.org> Tested-by: Jason Bagavatsingham <jason.bagavatsingham@gmail.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210425073451.2557394-1-ray.huang@amd.com
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=211791 Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When the weight of an active iocg is updated, weight_updated() is called
which in turn calls __propagate_weights() to update the active and inuse
weights so that the effective hierarchical weights are update accordingly.
The current implementation is incorrect for inner active nodes. For an
active leaf iocg, inuse can be any value between 1 and active and the
difference represents how much the iocg is donating. When weight is updated,
as long as inuse is clamped between 1 and the new weight, we're alright and
this is what __propagate_weights() currently implements.
However, that's not how an active inner node's inuse is set. An inner node's
inuse is solely determined by the ratio between the sums of inuse's and
active's of its children - ie. they're results of propagating the leaves'
active and inuse weights upwards. __propagate_weights() incorrectly applies
the same clamping as for a leaf when an active inner node's weight is
updated. Consider a hierarchy which looks like the following with saturating
workloads in AA and BB.
R
/ \
A B
| |
AA BB
1. For both A and B, active=100, inuse=100, hwa=0.5, hwi=0.5.
2. echo 200 > A/io.weight
3. __propagate_weights() update A's active to 200 and leave inuse at 100 as
it's already between 1 and the new active, making A:active=200,
A:inuse=100. As R's active_sum is updated along with A's active,
A:hwa=2/3, B:hwa=1/3. However, because the inuses didn't change, the
hwi's remain unchanged at 0.5.
4. The weight of A is now twice that of B but AA and BB still have the same
hwi of 0.5 and thus are doing the same amount of IOs.
Fix it by making __propgate_weights() always calculate the inuse of an
active inner iocg based on the ratio of child_inuse_sum to child_active_sum.
Patch series "mm/hugetlb: Fix issues on file sealing and fork", v2.
Hugh reported issue with F_SEAL_FUTURE_WRITE not applied correctly to
hugetlbfs, which I can easily verify using the memfd_test program, which
seems that the program is hardly run with hugetlbfs pages (as by default
shmem).
Meanwhile I found another probably even more severe issue on that hugetlb
fork won't wr-protect child cow pages, so child can potentially write to
parent private pages. Patch 2 addresses that.
After this series applied, "memfd_test hugetlbfs" should start to pass.
This patch (of 2):
F_SEAL_FUTURE_WRITE is missing for hugetlb starting from the first day.
There is a test program for that and it fails constantly.
These tests deliberately access these arrays out of bounds, which will
cause the dynamic local bounds checks inserted by
CONFIG_UBSAN_LOCAL_BOUNDS to fail and panic the kernel. To avoid this
problem, access the arrays via volatile pointers, which will prevent the
compiler from being able to determine the array bounds.
These accesses use volatile pointers to char (char *volatile) rather than
the more conventional pointers to volatile char (volatile char *) because
we want to prevent the compiler from making inferences about the pointer
itself (i.e. its array bounds), not the data that it refers to.
Link: https://lkml.kernel.org/r/20210507025915.1464056-1-pcc@google.com Link: https://linux-review.googlesource.com/id/I90b1713fbfa1bf68ff895aef099ea77b98a7c3b9 Signed-off-by: Peter Collingbourne <pcc@google.com> Tested-by: Alexander Potapenko <glider@google.com> Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com> Cc: Peter Collingbourne <pcc@google.com> Cc: George Popescu <georgepope@android.com> Cc: Elena Petrova <lenaptr@google.com> Cc: Evgenii Stepanov <eugenis@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
1. Userspace issues a UFFD ioctl, which ends up calling into
shmem_mfill_atomic_pte(). We successfully account the blocks, we
shmem_alloc_page(), but then the copy_from_user() fails. We return
-ENOENT. We don't release the page we allocated.
2. Our caller detects this error code, tries the copy_from_user() after
dropping the mmap_lock, and retries, calling back into
shmem_mfill_atomic_pte().
3. Meanwhile, let's say another process filled up the tmpfs being used.
4. So shmem_mfill_atomic_pte() fails to account blocks this time, and
immediately returns - without releasing the page.
This triggers a BUG_ON in our caller, which asserts that the page
should always be consumed, unless -ENOENT is returned.
To fix this, detect if we have such a "dangling" page when accounting
fails, and if so, release it before returning.
Link: https://lkml.kernel.org/r/20210428230858.348400-1-axelrasmussen@google.com Fixes: cb658a453b93 ("userfaultfd: shmem: avoid leaking blocks and used blocks in UFFDIO_COPY") Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Reported-by: Hugh Dickins <hughd@google.com> Acked-by: Hugh Dickins <hughd@google.com> Reviewed-by: Peter Xu <peterx@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Sysbot has reported a "divide error" which has been identified as being
caused by a corrupted file_size value within the file inode. This value
has been corrupted to a much larger value than expected.
Calculate_skip() is passed i_size_read(inode) >> msblk->block_log. Due to
the file_size value corruption this overflows the int argument/variable in
that function, leading to the divide error.
This patch changes the function to use u64. This will accommodate any
unexpectedly large values due to corruption.
The value returned from calculate_skip() is clamped to be never more than
SQUASHFS_CACHED_BLKS - 1, or 7. So file_size corruption does not lead to
an unexpectedly large return result here.
I believe there are some issues introduced by commit 31651c607151
("hfsplus: avoid deadlock on file truncation")
HFS+ has extent records which always contains 8 extents. In case the
first extent record in catalog file gets full, new ones are allocated from
extents overflow file.
In case shrinking truncate happens to middle of an extent record which
locates in extents overflow file, the logic in hfsplus_file_truncate() was
changed so that call to hfs_brec_remove() is not guarded any more.
Right action would be just freeing the extents that exceed the new size
inside extent record by calling hfsplus_free_extents(), and then check if
the whole extent record should be removed. However since the guard
(blk_cnt > start) is now after the call to hfs_brec_remove(), this has
unfortunate effect that the last matching extent record is removed
unconditionally.
To reproduce this issue, create a file which has at least 10 extents, and
then perform shrinking truncate into middle of the last extent record, so
that the number of remaining extents is not under or divisible by 8. This
causes the last extent record (8 extents) to be removed totally instead of
truncating into middle of it. Thus this causes corruption, and lost data.
Fix for this is simply checking if the new truncated end is below the
start of this extent record, making it safe to remove the full extent
record. However call to hfs_brec_remove() can't be moved to it's previous
place since we're dropping ->tree_lock and it can cause a race condition
and the cached info being invalidated possibly corrupting the node data.
Another issue is related to this one. When entering into the block
(blk_cnt > start) we are not holding the ->tree_lock. We break out from
the loop not holding the lock, but hfs_find_exit() does unlock it. Not
sure if it's possible for someone else to take the lock under our feet,
but it can cause hard to debug errors and premature unlocking. Even if
there's no real risk of it, the locking should still always be kept in
balance. Thus taking the lock now just before the check.
Link: https://lkml.kernel.org/r/20210429165139.3082828-1-jouni.roivas@tuxera.com Fixes: 31651c607151f ("hfsplus: avoid deadlock on file truncation") Signed-off-by: Jouni Roivas <jouni.roivas@tuxera.com> Reviewed-by: Anton Altaparmakov <anton@tuxera.com> Cc: Anatoly Trosinenko <anatoly.trosinenko@gmail.com> Cc: Viacheslav Dubeyko <slava@dubeyko.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The entry flush mitigation can be enabled/disabled at runtime via a
debugfs file (entry_flush), which causes the kernel to patch itself to
enable/disable the relevant mitigations.
However depending on which mitigation we're using, it may not be safe to
do that patching while other CPUs are active. For example the following
crash:
Shows that we returned to userspace with a corrupted LR that points into
the kernel, due to executing the partially patched call to the fallback
entry flush (ie. we missed the LR restore).
Fix it by doing the patching under stop machine. The CPUs that aren't
doing the patching will be spinning in the core of the stop machine
logic. That is currently sufficient for our purposes, because none of
the patching we do is to that code or anywhere in the vicinity.
Fixes: f79643787e0a ("powerpc/64s: flush L1D on kernel entry") Cc: stable@vger.kernel.org # v5.10+ Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20210506044959.1298123-2-mpe@ellerman.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The STF (store-to-load forwarding) barrier mitigation can be
enabled/disabled at runtime via a debugfs file (stf_barrier), which
causes the kernel to patch itself to enable/disable the relevant
mitigations.
However depending on which mitigation we're using, it may not be safe to
do that patching while other CPUs are active. For example the following
crash:
Shows that we returned to userspace without restoring the user r13
value, due to executing the partially patched STF exit code.
Fix it by doing the patching under stop machine. The CPUs that aren't
doing the patching will be spinning in the core of the stop machine
logic. That is currently sufficient for our purposes, because none of
the patching we do is to that code or anywhere in the vicinity.
Fixes: a048a07d7f45 ("powerpc/64s: Add support for a store forwarding barrier at kernel entry/exit") Cc: stable@vger.kernel.org # v4.17+ Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20210506044959.1298123-1-mpe@ellerman.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
arch/sh/kernel/traps.c: In function ‘nmi_trap_handler’:
arch/sh/kernel/traps.c:183:15: warning: unused variable ‘cpu’ [-Wunused-variable]
183 | unsigned int cpu = smp_processor_id();
Fixes: fe3f1d5d7cd3 ("sh: Get rid of nmi_count()") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210414170517.1205430-1-eric.dumazet@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This is because the fix expects highmem to be always less than
lowmem and uses min_low_pfn as an upper zone border for highmem.
max_high_pfn should be ok for both highmem and highmem+PAE cases.
Fixes: 4af22ded0ecf ("arc: fix memory initialization for systems with two memory banks") Signed-off-by: Vladimir Isaev <isaev@synopsys.com> Cc: Mike Rapoport <rppt@linux.ibm.com> Cc: stable@vger.kernel.org #5.8 onwards Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
32-bit PAGE_MASK can not be used as a mask for physical addresses
when PAE is enabled. PAGE_MASK_PHYS must be used for physical
addresses instead of PAGE_MASK.
Without this, init gets SIGSEGV if pte_modify was called:
| potentially unexpected fatal signal 11.
| Path: /bin/busybox
| CPU: 0 PID: 1 Comm: init Not tainted 5.12.0-rc5-00003-g1e43c377a79f-dirty
| Insn could not be fetched
| @No matching VMA found
| ECR: 0x00040000 EFA: 0x00000000 ERET: 0x00000000
| STAT: 0x80080082 [IE U ] BTA: 0x00000000
| SP: 0x5f9ffe44 FP: 0x00000000 BLK: 0xaf3d4
| LPS: 0x000d093e LPE: 0x000d0950 LPC: 0x00000000
| r00: 0x00000002 r01: 0x5f9fff14 r02: 0x5f9fff20
| ...
| Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
Signed-off-by: Vladimir Isaev <isaev@synopsys.com> Reported-by: kernel test robot <lkp@intel.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: stable@vger.kernel.org Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We have NR_syscall syscalls from [0 .. NR_syscall-1].
However the check for invalid syscall number is "> NR_syscall" as
opposed to >=. This off-by-one error erronesously allows "NR_syscall"
to be treated as valid syscall causeing out-of-bounds access into
syscall-call table ensuing a crash (holes within syscall table have a
invalid-entry handler but this is beyond the array implementing the
table).
This problem showed up on v5.6 kernel when testing glibc 2.33 (v5.10
kernel capable, includng faccessat2 syscall 439). The v5.6 kernel has
NR_syscalls=439 (0 to 438). Due to the bug, 439 passed by glibc was
not handled as -ENOSYS but processed leading to a crash.
If userspace exits before calling accept() on a listener that had at least
one new connection ready, we get:
Attempt to release TCP socket in state 8
This happens because the mptcp socket gets cloned when the TCP connection
is ready, but the socket is never exposed to userspace.
The client additionally sends a DATA_FIN, which brings connection into
CLOSE_WAIT state. This in turn prevents the orphan+state reset fixup
in mptcp_sock_destruct() from doing its job.
Fixes: 3721b9b64676b ("mptcp: Track received DATA_FIN sequence number and add related helpers") Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/185 Tested-by: Florian Westphal <fw@strlen.de> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Link: https://lore.kernel.org/r/20210507001638.225468-1-mathew.j.martineau@linux.intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Unlike other supported adapters, 2.5G and 5G use different
PHY type identifiers for reading/writing PHY settings
and for reading link status. This commit introduces
separate PHY identifiers for these two operation types.
Fixes: 2e45d3f4677a ("i40e: Add support for X710 B/P & SFP+ cards") Signed-off-by: Dawid Lukwinski <dawid.lukwinski@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Tested-by: Dave Switzer <david.switzer@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When FEC mode was changed the link didn't know it because
the link was not reset and new parameters were not negotiated.
Set a flag 'I40E_AQ_PHY_ENABLE_ATOMIC_LINK' in 'abilities'
to restart the link and make it run with the new settings.
Fixes: 1d96340196f1 ("i40e: Add support FEC configuration for Fortville 25G") Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Dave Switzer <david.switzer@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently the call to i40e_client_del_instance frees the object
pf->cinst, however pf->cinst->lan_info is being accessed after
the free. Fix this by adding the missing return.
Addresses-Coverity: ("Read from pointer after free") Fixes: 7b0b1a6d0ac9 ("i40e: Disable iWARP VSI PETCP_ENA flag on netdev down events") Signed-off-by: Yunjian Wang <wangyunjian@huawei.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit 12738ac4754e ("i40e: Fix sparse errors in i40e_txrx.c") broke
XDP support in the i40e driver. That commit was fixing a sparse error
in the code by introducing a new variable xdp_res instead of
overloading this into the skb pointer. The problem is that the code
later uses the skb pointer in if statements and these where not
extended to also test for the new xdp_res variable. Fix this by adding
the correct tests for xdp_res in these places.
The skb pointer was used to store the result of the XDP program by
overloading the results in the error pointer
ERR_PTR(-result). Therefore, the allocation failure test that used to
only test for !skb now need to be extended to also consider !xdp_res.
i40e_cleanup_headers() had a check that based on the skb value being
an error pointer, i.e. a result from the XDP program != XDP_PASS, and
if so start to process a new packet immediately, instead of populating
skb fields and sending the skb to the stack. This check is not needed
anymore, since we have added an explicit test for xdp_res being set
and if so just do continue to pick the next packet from the NIC.
Fixes: 12738ac4754e ("i40e: Fix sparse errors in i40e_txrx.c") Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Tested-by: Jesper Dangaard Brouer <brouer@redhat.com> Reported-by: Jesper Dangaard Brouer <brouer@redhat.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
It used to be true that we can have system RAM (IORESOURCE_SYSTEM_RAM |
IORESOURCE_BUSY) only on the first level in the resource tree. However,
this is no longer holds for driver-managed system RAM (i.e., added via
dax/kmem and virtio-mem), which gets added on lower levels, for example,
inside device containers.
IORESOURCE_SYSTEM_RAM is defined as IORESOURCE_MEM | IORESOURCE_SYSRAM and
just a special type of IORESOURCE_MEM.
The function walk_mem_res() only considers the first level and is used in
arch/x86/mm/ioremap.c:__ioremap_check_mem() only. We currently fail to
identify System RAM added by dax/kmem and virtio-mem as
"IORES_MAP_SYSTEM_RAM", for example, allowing for remapping of such
"normal RAM" in __ioremap_caller().
Let's find all IORESOURCE_MEM | IORESOURCE_BUSY resources, making the
function behave similar to walk_system_ram_res().
Link: https://lkml.kernel.org/r/20210325115326.7826-3-david@redhat.com Fixes: ebf71552bb0e ("virtio-mem: Add parent resource for all added "System RAM"") Fixes: c221c0b0308f ("device-dax: "Hotplug" persistent memory for use like normal RAM") Signed-off-by: David Hildenbrand <david@redhat.com> Reviewed-by: Dan Williams <dan.j.williams@intel.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Cc: Dave Young <dyoung@redhat.com> Cc: Baoquan He <bhe@redhat.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Keith Busch <keith.busch@intel.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Qian Cai <cai@lca.pw> Cc: Oscar Salvador <osalvador@suse.de> Cc: Eric Biederman <ebiederm@xmission.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Tom Lendacky <thomas.lendacky@amd.com> Cc: Brijesh Singh <brijesh.singh@amd.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Patch series "kernel/resource: make walk_system_ram_res() and walk_mem_res() search the whole tree", v2.
Playing with kdump+virtio-mem I noticed that kexec_file_load() does not
consider System RAM added via dax/kmem and virtio-mem when preparing the
elf header for kdump. Looking into the details, the logic used in
walk_system_ram_res() and walk_mem_res() seems to be outdated.
walk_system_ram_range() already does the right thing, let's change
walk_system_ram_res() and walk_mem_res(), and clean up.
Loading a kdump kernel via "kexec -p -s" ... will result in the kdump
kernel to also dump dax/kmem and virtio-mem added System RAM now.
Note: kexec-tools on x86-64 also have to be updated to consider this
memory in the kexec_load() case when processing /proc/iomem.
This patch (of 3):
It used to be true that we can have system RAM (IORESOURCE_SYSTEM_RAM |
IORESOURCE_BUSY) only on the first level in the resource tree. However,
this is no longer holds for driver-managed system RAM (i.e., added via
dax/kmem and virtio-mem), which gets added on lower levels, for example,
inside device containers.
We have two users of walk_system_ram_res(), which currently only
consideres the first level:
a) kernel/kexec_file.c:kexec_walk_resources() -- We properly skip
IORESOURCE_SYSRAM_DRIVER_MANAGED resources via
locate_mem_hole_callback(), so even after this change, we won't be
placing kexec images onto dax/kmem and virtio-mem added memory. No
change.
b) arch/x86/kernel/crash.c:fill_up_crash_elf_data() -- we're currently
not adding relevant ranges to the crash elf header, resulting in them
not getting dumped via kdump.
This change fixes loading a crashkernel via kexec_file_load() and
including dax/kmem and virtio-mem added System RAM in the crashdump on
x86-64. Note that e.g,, arm64 relies on memblock data and, therefore,
always considers all added System RAM already.
Let's find all IORESOURCE_SYSTEM_RAM | IORESOURCE_BUSY resources, making
the function behave like walk_system_ram_range().
Link: https://lkml.kernel.org/r/20210325115326.7826-1-david@redhat.com Link: https://lkml.kernel.org/r/20210325115326.7826-2-david@redhat.com Fixes: ebf71552bb0e ("virtio-mem: Add parent resource for all added "System RAM"") Fixes: c221c0b0308f ("device-dax: "Hotplug" persistent memory for use like normal RAM") Signed-off-by: David Hildenbrand <david@redhat.com> Reviewed-by: Dan Williams <dan.j.williams@intel.com> Acked-by: Baoquan He <bhe@redhat.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Cc: Dave Young <dyoung@redhat.com> Cc: Baoquan He <bhe@redhat.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Keith Busch <keith.busch@intel.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Qian Cai <cai@lca.pw> Cc: Oscar Salvador <osalvador@suse.de> Cc: Eric Biederman <ebiederm@xmission.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Tom Lendacky <thomas.lendacky@amd.com> Cc: Brijesh Singh <brijesh.singh@amd.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When vzalloc() returns NULL to sha_regions, no error return code of
kexec_calculate_store_digests() is assigned. To fix this bug, ret is
assigned with -ENOMEM in this case.
Link: https://lkml.kernel.org/r/20210309083904.24321-1-baijiaju1990@gmail.com Fixes: a43cac0d9dc2 ("kexec: split kexec_file syscall code to kexec_file.c") Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Acked-by: Baoquan He <bhe@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>