Default remotes are stored as FDB entries with an Ethernet address of
00:00:00:00:00:00. When a request is made to change a remote address of
a VXLAN device, vxlan_changelink() first deletes the existing default
remote, and then creates a new FDB entry.
This works well as long as the list of default remotes matches exactly
the configuration of a VXLAN remote address. Thus when the VXLAN device
has a remote of X, there should be exactly one default remote FDB entry
X. If the VXLAN device has no remote address, there should be no such
entry.
Besides using "ip link set", it is possible to manipulate the list of
default remotes by using the "bridge fdb". It is therefore easy to break
the above condition. Under such circumstances, the __vxlan_fdb_delete()
call doesn't delete the FDB entry itself, but just one remote. The
following vxlan_fdb_create() then creates a new FDB entry, leading to a
situation where two entries exist for the address 00:00:00:00:00:00,
each with a different subset of default remotes.
An even more obvious breakage rooted in the same cause can be observed
when a remote address is configured for a VXLAN device that did not have
one before. In that case vxlan_changelink() doesn't remove any remote,
and just creates a new FDB entry for the new address:
$ ip link add name vx up type vxlan id 2000 dstport 4789
$ bridge fdb ap dev vx 00:00:00:00:00:00 dst 192.0.2.20 self permanent
$ bridge fdb ap dev vx 00:00:00:00:00:00 dst 192.0.2.30 self permanent
$ ip link set dev vx type vxlan remote 192.0.2.30
$ bridge fdb sh dev vx | grep 00:00:00:00:00:00
00:00:00:00:00:00 dst 192.0.2.30 self permanent <- new entry, 1 rdst
00:00:00:00:00:00 dst 192.0.2.20 self permanent <- orig. entry, 2 rdsts
00:00:00:00:00:00 dst 192.0.2.30 self permanent
To fix this, instead of calling vxlan_fdb_create() directly, defer to
vxlan_fdb_update(). That has logic to handle the duplicates properly.
Additionally, it also handles notifications, so drop that call from
changelink as well.
Fixes: 0241b836732f ("vxlan: fix default fdb entry netlink notify ordering during netdev create") Signed-off-by: Petr Machata <petrm@mellanox.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The IP10[5:3] field in Peripheral Function Select Register 10 has a
width of 3 bits, i.e. it allows programming one out of 8 different
configurations.
However, 9 values are provided instead of 8, overflowing into the
subsequent field in the register, and thus breaking the configuration of
the latter.
The Port C I/O Register 0 contains 7 reserved bits, but the descriptor
contains only dummy configuration values for 6 reserved bits, thus
breaking the configuration of all subsequent fields in the register.
Fix this by adding the two missing configuration values.
The Peripheral Function Select Register 11 contains 3 reserved bits and
15 variable-width fields, but the variable field descriptor does not
contain the 3-bit field IP11[25:23].
Fixes: 856cb4bb337ee504 ("sh: Add support pinmux for SH7734") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The vin1_b_data18_mux[] arrays contains pin marks for the 2 LSB bits of
the color components. The vin1_b_data18_pins[] array rightfully does
not include the corresponding pin numbers, as RGB18 is subset of RGB24,
containing only the 6 MSB bits of each component.
The qspi_data4_b_mux[] array contains pin marks for the clock and chip
select pins. The qspi_data4_b_pins[] array rightfully does not contain
the corresponding pin numbers, as the control pins are provided by a
separate group (qspi_ctrl_b).
After submitting a Firmware Download MRPC command, Switchtec firmware will
delay Management EP BAR MemRd TLP responses by more than 10ms. This is a
firmware limitation. Delayed MemRd completions are a problem for systems
with a low Completion Timeout (CTO).
The current driver checks the MRPC status immediately after submitting an
MRPC command, which results in a delayed MemRd completion that may cause a
Completion Timeout.
Remove the immediate status check and rely on the check after receiving an
interrupt or timing out.
This is only a software workaround to the READ issue and a proper fix of
this should be done in firmware.
Abort the probing of the camera driver in case there isn't a camera
actually connected to the Raspberry Pi. This solution also avoids a
NULL ptr dereference of mmal instance on driver unload.
Fixes: 7b3ad5abf027 ("staging: Import the BCM2835 MMAL-based V4L2 camera driver.") Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Jerry Zuo pointed out a rather obscure hotplugging issue that it seems I
accidentally introduced into DRM two years ago.
Pretend we have a topology like this:
|- DP-1: mst_primary
|- DP-4: active display
|- DP-5: disconnected
|- DP-6: active hub
|- DP-7: active display
|- DP-8: disconnected
|- DP-9: disconnected
If we unplug DP-6, the topology starting at DP-7 will be destroyed but
it's payloads will live on in DP-1's VCPI allocations and thus require
removal. However, this removal currently fails because
drm_dp_update_payload_part1() will (rightly so) try to validate the port
before accessing it, fail then abort. If we keep going, eventually we
run the MST hub out of bandwidth and all new allocations will start to
fail (or in my case; all new displays just start flickering a ton).
We could just teach drm_dp_update_payload_part1() not to drop the port
ref in this case, but then we also need to teach
drm_dp_destroy_payload_step1() to do the same thing, then hope no one
ever adds anything to the that requires a validated port reference in
drm_dp_destroy_connector_work(). Kind of sketchy.
So let's go with a more clever solution: any port that
drm_dp_destroy_connector_work() interacts with is guaranteed to still
exist in memory until we say so. While said port might not be valid we
don't really care: that's the whole reason we're destroying it in the
first place! So, teach drm_dp_get_validated_port_ref() to use the all
mighty current_work() function to avoid attempting to validate ports
from the context of mgr->destroy_connector_work. I can't see any
situation where this wouldn't be safe, and this avoids having to play
whack-a-mole in the future of trying to work around port validation.
Signed-off-by: Lyude Paul <lyude@redhat.com> Fixes: 263efde31f97 ("drm/dp/mst: Get validated port ref in drm_dp_update_payload_part1()") Reported-by: Jerry Zuo <Jerry.Zuo@amd.com> Cc: Jerry Zuo <Jerry.Zuo@amd.com> Cc: Harry Wentland <Harry.Wentland@amd.com> Cc: <stable@vger.kernel.org> # v4.6+ Reviewed-by: Dave Airlie <airlied@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181113224613.28809-1-lyude@redhat.com Signed-off-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Passing string 'name' as the format specifier is potentially hazardous
because name could (although very unlikely to) have a format specifier
embedded in it causing issues when parsing the non-existent arguments
to these. Follow best practice by using the "%s" format string for
the string 'name'.
Cleans up clang warning:
crypto/pcrypt.c:397:40: warning: format string is not a string literal
(potentially insecure) [-Wformat-security]
Fixes: a3fb1e330dd2 ("pcrypt: Added sysfs interface to pcrypt") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Add QEEC.mise (minimum shaper enable) and QEEC.min_shaper_rate to enable
configuration of minimum shaper.
Increase the QEEC length to 0x20 as well: that's the length that the
register has had for a long time now, but with the configurations that
mlxsw typically exercises, the firmware tolerated 0x1C-sized packets.
With mise=true however, FW rejects packets unless they have the full
required length.
Fixes: b9b7cee40579 ("mlxsw: reg: Add QoS ETS Element Configuration register") Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The is_double flag is a boolean currently assigned to the value of the d
variable, that is either 1 or 2. It means that this is_double variable is
always set to true, even though the initial intent was to have it set to
true when d is 2.
Fixes two problems introduced as early as
commit 03aef4b6dc12 ("Staging: comedi: add ni_mio_common code"):
(1) Ensures that the last four bits of NISTC_RTSI_TRIGB_OUT_REG register is
not unduly overwritten on e-series devices. On e-series devices, the
first three of the last four bits are reserved. The last bit defines
the output selection of the RGOUT0 pin, otherwise known as
RTSI_Sub_Selection. For m-series devices, these last four bits are
indeed used as the output selection of the RTSI7 pin (and the
RTSI_Sub_Selection bit for the RGOUT0 pin is moved to the
RTSI_Trig_Direction register.
(2) Allows all 4 RTSI_BRD lines to be treated as valid sources for RTSI
lines.
This patch also cleans up the ni_get_rtsi_routing command for readability.
A quirk in snd-usb-audio was added to automate setting sample rate to
4800k and remove the previously exposed nonfunctional microphone for
the Bowers & Wilkins PX:
commit 240a8af929c7c57dcde28682725b29cf8474e8e5
https://lore.kernel.org/patchwork/patch/919689/
However the headphones where updated shortly after that to remove the
unintentional microphone functionality. I guess because of this the
headphones now crash when connecting them via USB while the quirk is
active. Dmesg:
snd-usb-audio: probe of 2-3:1.0 failed with error -22
usb 2-3: 2:1: cannot get min/max values for control 2 (id 2)
This patch removes the microfone and allows the headphones to connect
and work out of the box. It is based on the current mainline kernel
and successfully applied an tested on my machine (4.18.10.arch1-1).
Fixes: 240a8af929c7 ("ALSA: usb-audio: Add a quirck for B&W PX headphones") Signed-off-by: Nicolas Huaman <nicolas@herochao.de> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since Virtual Lanes BCT credits and MTU are set through separate MADs, we
have to ensure both are valid, and data VLs are ready for transmission
before we allow port transition to Armed state.
Fixes: 5e2d6764a729 ("IB/hfi1: Verify port data VLs credits on transition to Armed") Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com> Signed-off-by: Alex Estrin <alex.estrin@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently the driver overwrites the surface depth provided by the fb
helper to give an invalid bpp/surface depth combination.
This has been exposed by commit 70109354fed2 ("drm: Reject unknown legacy
bpp and depth for drm_mode_addfb ioctl"), which now causes the driver to
fail to probe.
Fix by not overwriting the surface depth.
Fixes: d1667b86795a ("drm/hisilicon/hibmc: Add support for frame buffer") Signed-off-by: John Garry <john.garry@huawei.com> Reviewed-by: Xinliang Liu <z.liuxinliang@hisilicon.com> Signed-off-by: Xinliang Liu <z.liuxinliang@hisilicon.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Fix previous incorrect logic that limits PAXC slot number to zero only.
In order for SRIOV/VF to work, we need to allow the slot number to be
greater than zero.
Fixes: 46560388c476c ("PCI: iproc: Allow multiple devices except on PAXC") Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com> Signed-off-by: Ray Jui <ray.jui@broadcom.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Andy Gospodarek <gospo@broadcom.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
As a comment above begin_current_label_crit_section() explains,
begin_current_label_crit_section() must run in sleepable context because
when label_is_stale() is true, aa_replace_current_label() runs, which uses
prepare_creds(), which can sleep.
Until now, the ptrace access check (which runs with a task lock held)
violated this rule.
Also add a might_sleep() assertion to begin_current_label_crit_section(),
because asserts are less likely to be ignored than comments.
Fixes: b2d09ae449ced ("apparmor: move ptrace checks to using labels") Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This doesn't affect runtime because in the current code "idx" is always
valid.
First, we read from "vgdev->capsets[idx].max_size" before checking
whether "idx" is within bounds. And secondly the bounds check is off by
one so we could end up reading one element beyond the end of the
vgdev->capsets[] array.
Removing the drm_bridge_remove call should avoid a NULL dereference
during list processing in drm_bridge_remove if the error path is ever
taken.
The more natural approach would perhaps be to add a drm_bridge_add,
but there are several other bridges that never call drm_bridge_add.
Just removing the drm_bridge_remove is the easier fix.
Fixes: 84601dbdea36 ("drm: sti: rework init sequence") Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Peter Rosin <peda@axentia.se> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20180806061910.29914-2-peda@axentia.se Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In function __tipc_shutdown(), the timeout value passed to
tipc_wait_for_cond() is not jiffies.
This commit fixes it by converting that value from milliseconds
to jiffies.
Fixes: 365ad353c256 ("tipc: reduce risk of user starvation during link congestion") Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
powerpc: Use hardware RNG for arch_get_random_seed_* not arch_get_random_*
updated arch_get_random_[int|long]() to be NOPs, and moved the hardware
RNG backing to arch_get_random_seed_[int|long]() instead. However, it
failed to take into account that arch_get_random_int() was implemented
in terms of arch_get_random_long(), and so we ended up with a version
of the former that is essentially a NOP as well.
Fix this by calling arch_get_random_seed_long() from
arch_get_random_seed_int() instead.
Fixes: 01c9348c7620ec65 ("powerpc: Use hardware RNG for arch_get_random_seed_* not arch_get_random_*") Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20191204115015.18015-1-ardb@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
It turned out Intel Gemini Lake doesn't use the same I2C timing
parameters as Broxton.
I got confirmation from the Windows team that Gemini Lake systems should
use updated timing parameters that differ from those used in Broxton
based systems.
Fixes: f80e78aa11ad ("mfd: intel-lpss: Add Intel Gemini Lake PCI IDs") Tested-by: Chris Chiu <chiu@endlessm.com> Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Flags passed to Q_XQUOTARM were not sanity checked for invalid values.
Fix that.
Fixes: 9da93f9b7cdf ("xfs: fix Q_XQUOTARM ioctl") Reported-by: Yang Xu <xuyang2018.jy@cn.fujitsu.com> Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If the BAR initialization failed it may leave the vmm structure in an
unitialized state, leading to a null-pointer-dereference when the vmm is
dereferenced during teardown.
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sushma Kalakota <sushmax.kalakota@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If the BAR is zero size, it indicates it was never successfully mapped.
Ensure that the BAR is valid during initialization before attempting to
use it.
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sushma Kalakota <sushmax.kalakota@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Due to the use of sizeof(), command size set for the spi transfer
was wrong. Driver was sending and receiving always 1 byte less
and especially on write, it was hanging.
echo -n -e "\\x1\\x2\\x3\\x4" > /dev/mtd1
And read part too now works as expected.
hexdump -C -n16 /dev/mtd1 00000000 01 02 03 04 ab f3 ad c2 ab e3 f4 36 dd 38 04 15 00000010
Fixes: 4379075a870b ("mtd: mchp23k256: Add support for mchp23lcv1024") Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
At the time commit ce5ec440994b ("tcp: ensure epoll edge trigger
wakeup when write queue is empty") was added to the kernel,
we still had a single write queue, combining rtx and write queues.
Once we moved the rtx queue into a separate rb-tree, testing
if sk_write_queue is empty has been suboptimal.
Indeed, if we have packets in the rtx queue, we probably want
to delay the EPOLLOUT generation at the time incoming packets
will free them, making room, but more importantly avoiding
flooding application with EPOLLOUT events.
Solution is to use tcp_rtx_and_write_queues_empty() helper.
Fixes: 75c119afe14f ("tcp: implement rb-tree based retransmit queue") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jason Baron <jbaron@akamai.com> Cc: Neal Cardwell <ncardwell@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Per-port counter cache used by Qdiscs is updated periodically, unless the
port is down. The fact that the cache is not updated for down ports is no
problem for most counters, which are relative in nature. However, backlog
is absolute in nature, and if there is a non-zero value in the cache around
the time that the port goes down, that value just stays there. This value
then leaks to offloaded Qdiscs that report non-zero backlog even if
there (obviously) is no traffic.
The HW does not keep backlog of a downed port, so do likewise: as the port
goes down, wipe the backlog value from xstats.
Fixes: 075ab8adaf4e ("mlxsw: spectrum: Collect tclass related stats periodically") Signed-off-by: Petr Machata <petrm@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The 1.5 version of Engicam's i.Core MX6 CPU module features a different clock
provider for the ethernet's PHY interface. Adjust the FEC ptp clock to
reference CLK_ENET_REF clock source, and set SION bit of
MX6QDL_PAD_GPIO_16__ENET_REF_CLK to adjust the input path of that pin.
The newly introduced imx6ql-icore-1.5.dtsi allows to collect in a single
place differences between version '1.0' and '1.5' of the module.
btrfs_del_root_ref() will simply WARN_ON() if the ref doesn't match in
any way, and then continue to delete the reference. This shouldn't
happen, we have these values because there's more to the reference than
the original root and the sub root. If any of these checks fail, return
-ENOENT.
CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Fix build error:
./drivers/gpu/drm/i915/selftests/i915_random.h: In function i915_prandom_u32_max_state:
./drivers/gpu/drm/i915/selftests/i915_random.h:48:23: error:
implicit declaration of function mul_u32_u32; did you mean mul_u64_u32_div? [-Werror=implicit-function-declaration]
return upper_32_bits(mul_u32_u32(prandom_u32_state(state), ep_ro));
Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: 7ce5b6850b47 ("drm/i915/selftests: Use mul_u32_u32() for 32b x 32b -> 64b result") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20200107135014.36472-1-yuehaibing@huawei.com
(cherry picked from commit 62bf5465b26d1f502430b9c654be7d16bf2e242d) Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This patch provides a general mechanism for passing flags to the
security_capable LSM hook. It replaces the specific 'audit' flag that is
used to tell security_capable whether it should log an audit message for
the given capability check. The reason for generalizing this flag
passing is so we can add an additional flag that signifies whether
security_capable is being called by a setid syscall (which is needed by
the proposed SafeSetID LSM).
The PMU registers are at least 0x18 bytes wide. Meson8b already uses a
size of 0x18. The structure of the PMU registers on Meson8 and Meson8b
is similar but not identical.
Meson8 and Meson8b have the following registers in common (starting at
AOBUS + 0xe0):
#define AO_RTI_PWR_A9_CNTL0 0xe0 (0x38 << 2)
#define AO_RTI_PWR_A9_CNTL1 0xe4 (0x39 << 2)
#define AO_RTI_GEN_PWR_SLEEP0 0xe8 (0x3a << 2)
#define AO_RTI_GEN_PWR_ISO0 0x4c (0x3b << 2)
Meson8b additionally has these three registers:
#define AO_RTI_GEN_PWR_ACK0 0xf0 (0x3c << 2)
#define AO_RTI_PWR_A9_MEM_PD0 0xf4 (0x3d << 2)
#define AO_RTI_PWR_A9_MEM_PD1 0xf8 (0x3e << 2)
Thus we can assume that the register size of the PMU IP blocks is
identical on both SoCs (and Meson8 just contains some reserved registers
in that area) because the CEC registers start right after the PMU
(AO_RTI_*) registers at AOBUS + 0x100 (0x40 << 2).
The upcoming power domain driver will need to read and write the
AO_RTI_GEN_PWR_SLEEP0 and AO_RTI_GEN_PWR_ISO0 registers, so the updated
size is needed for that driver to work.
Fixes: 4a5a27116b447d ("ARM: dts: meson8: add support for booting the secondary CPU cores") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Those regulators are not actually supported by the AB8500 regulator
driver. There is no ab8500_regulator_info for them and no entry in
ab8505_regulator_match.
As such, they cannot be registered successfully, and looking them
up in ab8505_regulator_match causes an out-of-bounds array read.
Fixes: 547f384f33db ("regulator: ab8500: add support for ab8505") Cc: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20191106173125.14496-2-stephan@gerhold.net Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since there are some DIE which has only ranges instead of the
combination of entrypc/highpc, address verification must use
dwarf_haspc() instead of dwarf_entrypc/dwarf_highpc.
Also, the ranges only DIE will have a partial code in different section
(e.g. unlikely code will be in text.unlikely as "FUNC.cold" symbol). In
that case, we can not use dwarf_entrypc() or die_entrypc(), because the
offset from original DIE can be a minus value.
Instead, this simply gets the symbol and offset from symtab.
Without this patch;
# perf probe -D clear_tasks_mm_cpumask:1
Failed to get entry address of clear_tasks_mm_cpumask
Error: Failed to add events.
This patch fixes an unintended sign extension on left shifts. From Colin
King: "Shifting a u8 left will cause the value to be promoted to an
integer. If the top bit of the u8 is set then the following conversion to
an u64 will sign extend the value causing the upper 32 bits to be set in
the result."
Fix this by using get_unaligned_be*() instead.
Fixes: bf8162354233 ("[SCSI] add scsi trace core functions and put trace points") Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.com> Cc: Douglas Gilbert <dgilbert@interlog.com> Link: https://lore.kernel.org/r/20191101211447.187151-1-bvanassche@acm.org Reported-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In qla2x00_find_all_fabric_devs(), fcport->flags & FCF_LOGIN_NEEDED is a
necessary condition for logging into new rports, but not for dropping lost
ones.
Fixes: 726b85487067 ("qla2xxx: Add framework for async fabric discovery") Link: https://lore.kernel.org/r/20191122221912.20100-2-martin.wilck@suse.com Tested-by: David Bond <dbond@suse.com> Signed-off-by: Martin Wilck <mwilck@suse.com> Acked-by: Himanshu Madhani <hmadhani@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 4fa183455988 ("scsi: qla2xxx: Utilize pci_alloc_irq_vectors/
pci_free_irq_vectors calls.") use pci_alloc_irq_vectors() to replace
pci_enable_msi() but it didn't handle the return value correctly. This bug
make qla2x00 always fail to setup MSI if MSI-X fail, so fix it.
BTW, improve the log message of return value in qla2x00_request_irqs() to
avoid confusion.
Fixes: 4fa183455988 ("scsi: qla2xxx: Utilize pci_alloc_irq_vectors/pci_free_irq_vectors calls.") Cc: Michael Hernandez <michael.hernandez@cavium.com> Link: https://lore.kernel.org/r/1574314847-14280-1-git-send-email-chenhc@lemote.com Signed-off-by: Huacai Chen <chenhc@lemote.com> Acked-by: Himanshu Madhani <hmadhani@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Print the string for which conversion failed instead of printing the
function name twice.
Fixes: 2650d71e244f ("target: move transport ID handling to the core") Cc: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20191107215525.64415-1-bvanassche@acm.org Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The member hba->pcidev may be used after its reference is dropped. Move the
put function to where it is never used to avoid potential use after free
issues.
Fixes: a77171806515 ("[SCSI] bnx2i: Removed the reference to the netdev->base_addr") Link: https://lore.kernel.org/r/1573043541-19126-1-git-send-email-bianpan2016@163.com Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The variable init_fw_cb is released twice, resulting in a double free
bug. The call to the function dma_free_coherent() before goto is removed to
get rid of potential double free.
Fixes: 2a49a78ed3c8 ("[SCSI] qla4xxx: added IPv6 support.") Link: https://lore.kernel.org/r/1572945927-27796-1-git-send-email-bianpan2016@163.com Signed-off-by: Pan Bian <bianpan2016@163.com> Acked-by: Manish Rangankar <mrangankar@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 60e4cf67a58 (reiserfs: fix extended attributes on the root
directory) introduced a regression open_xa_root started returning
-EOPNOTSUPP but it was not handled properly in reiserfs_for_each_xattr.
When the reiserfs module is built without CONFIG_REISERFS_FS_XATTR,
deleting an inode would result in a warning and chowning an inode
would also result in a warning and then fail to complete.
With CONFIG_REISERFS_FS_XATTR enabled, the xattr root would always be
present for read-write operations.
This commit handles -EOPNOSUPP in the same way -ENODATA is handled.
Fixes: 60e4cf67a582 ("reiserfs: fix extended attributes on the root directory") CC: stable@vger.kernel.org # Commit 60e4cf67a58 was picked up by stable Link: https://lore.kernel.org/r/20200115180059.6935-1-jeffm@suse.com Reported-by: Michael Brunnbauer <brunni@netestate.de> Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 951d48855d86 ("of: Make of_dma_get_range() work on bus nodes")
reworked the logic such that of_dma_get_range() works correctly
starting from a bus node containing "dma-ranges".
Since on Juno we don't have a SoC level bus node and "dma-ranges" is
present only in the root node, we get the following error:
OF: translation of DMA address(0) to CPU address failed node(/sram@2e000000)
OF: translation of DMA address(0) to CPU address failed node(/uart@7ff80000)
...
OF: translation of DMA address(0) to CPU address failed node(/mhu@2b1f0000)
OF: translation of DMA address(0) to CPU address failed node(/iommu@2b600000)
OF: translation of DMA address(0) to CPU address failed node(/iommu@2b600000)
OF: translation of DMA address(0) to CPU address failed node(/iommu@2b600000)
So let's fix it by dropping the "dma-ranges" property for now. This
should be fine since it doesn't represent any kind of device-visible
restriction; it was only there for completeness, and we've since given
in to the assumption that missing "dma-ranges" implies a 1:1 mapping
anyway.
We can add it later with a proper SoC bus node and moving all the
devices that belong there along with the "dma-ranges" if required.
Fixes: 193d00a2b35e ("arm64: dts: juno: add dma-ranges property") Cc: Rob Herring <robh+dt@kernel.org> Cc: Liviu Dudau <liviu.dudau@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.0-rc7+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Use READ_ONCE() and WRITE_ONCE() to annotate this expected race.
Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20191205045619.204946-1-edumazet@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
arch/arm/dts/meson-gxl-s905x-khadas-vim.dtb: Warning (avoid_unnecessary_addr_size):
/gpio-keys-polled: unnecessary #address-cells/#size-cells
without "ranges" or child "reg" property
Fixes: e15d2774b8c0 ("ARM64: dts: meson-gxl: add support for the Khadas VIM board") Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
../drivers/block/xen-blkfront.c:1117:4: warning: misleading indentation;
statement is not part of the previous 'if' [-Wmisleading-indentation]
nr_parts = PARTS_PER_DISK;
^
../drivers/block/xen-blkfront.c:1115:3: note: previous statement is here
if (err)
^
This is because there is a space at the beginning of this line; remove
it so that the indentation is consistent according to the Linux kernel
coding style and clang no longer warns.
While we are here, the previous line has some trailing whitespace; clean
that up as well.
When the packet pointed to by retransmit_skb_hint is unlinked by ACK,
retransmit_skb_hint will be set to NULL in tcp_clean_rtx_queue().
If packet loss is detected at this time, retransmit_skb_hint will be set
to point to the current packet loss in tcp_verify_retransmit_hint(),
then the packets that were previously marked lost but not retransmitted
due to the restriction of cwnd will be skipped and cannot be
retransmitted.
To fix this, when retransmit_skb_hint is NULL, retransmit_skb_hint can
be reset only after all marked lost packets are retransmitted
(retrans_out >= lost_out), otherwise we need to traverse from
tcp_rtx_queue_head in tcp_xmit_retransmit_queue().
Packetdrill to demonstrate:
// Disable RACK and set max_reordering to keep things simple
0 `sysctl -q net.ipv4.tcp_recovery=0`
+0 `sysctl -q net.ipv4.tcp_max_reordering=3`
// Send 8 data segments
+0 write(4, ..., 8000) = 8000
+0 > P. 1:8001(8000) ack 1
// Enter recovery and 1:3001 is marked lost
+.01 < . 1:1(0) ack 1 win 257 <sack 3001:4001,nop,nop>
+0 < . 1:1(0) ack 1 win 257 <sack 5001:6001 3001:4001,nop,nop>
+0 < . 1:1(0) ack 1 win 257 <sack 5001:7001 3001:4001,nop,nop>
// Retransmit 1:1001, now retransmit_skb_hint points to 1001:2001
+0 > . 1:1001(1000) ack 1
// 1001:2001 was ACKed causing retransmit_skb_hint to be set to NULL
+.01 < . 1:1(0) ack 2001 win 257 <sack 5001:8001 3001:4001,nop,nop>
// Now retransmit_skb_hint points to 4001:5001 which is now marked lost
// BUG: 2001:3001 was not retransmitted
+0 > . 2001:3001(1000) ack 1
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com> Acked-by: Neal Cardwell <ncardwell@google.com> Tested-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Add missing endpoint sanity check to probe in order to prevent a
NULL-pointer dereference (or slab out-of-bounds access) when retrieving
the interrupt-endpoint bInterval on ndo_open() in case a device lacks
the expected endpoints.
Fixes: 40a82917b1d3 ("net/usb/r8152: enable interrupt transfer") Cc: hayeswang <hayeswang@realtek.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There is a bug in ptp_clock_unregister(), where ptp_cleanup_pin_groups()
first frees ptp->pin_{,dev_}attr, but then posix_clock_unregister() needs
them to destroy a related sysfs device.
These functions can not be just swapped, as posix_clock_unregister() frees
ptp which is needed in the ptp_cleanup_pin_groups(). Fix this by calling
ptp_cleanup_pin_groups() in ptp_clock_release(), right before ptp is freed.
This makes this patch fix an UAF bug in a patch which fixes an UAF bug.
Reported-by: Antti Laakso <antti.laakso@intel.com> Fixes: a33121e5487b ("ptp: fix the race between the release of ptp_clock and cdev") Link: https://lore.kernel.org/netdev/3d2bd09735dbdaf003585ca376b7c1e5b69a19bd.camel@intel.com/ Signed-off-by: Vladis Dronov <vdronov@redhat.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Array utdm_info is declared as an array of MAX_HDLC_NUM (4) elements
however up to UCC_MAX_NUM (8) elements are potentially being written
to it. Currently we have an array out-of-bounds write error on the
last 4 elements. Fix this by making utdm_info UCC_MAX_NUM elements in
size.
Addresses-Coverity: ("Out-of-bounds write") Fixes: c19b6d246a35 ("drivers/net: support hdlc function for QE-UCC") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
lan78xx_tx_bh() makes sure to not exceed MAX_SINGLE_PACKET_SIZE
bytes in the aggregated packets it builds, but does
nothing to prevent large GSO packets being submitted.
Pierre-Francois reported various hangs when/if TSO is enabled.
For localy generated packets, we can use netif_set_gso_max_size()
to limit the size of TSO packets.
Note that forwarded packets could still hit the issue,
so a complete fix might require implementing .ndo_features_check
for this driver, forcing a software segmentation if the size
of the TSO packet exceeds MAX_SINGLE_PACKET_SIZE.
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: RENARD Pierre-Francois <pfrenard@gmail.com> Tested-by: RENARD Pierre-Francois <pfrenard@gmail.com> Cc: Stefan Wahren <stefan.wahren@i2se.com> Cc: Woojung Huh <woojung.huh@microchip.com> Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When there is not enough memory and napi_alloc_skb() return NULL,
the HNS driver will print error message, and than try again, if
the memory is not enough for a while, huge error message and the
retry operation will cause soft lockup.
When napi_alloc_skb() return NULL because of no memory, we can
get a warn_alloc() call trace, so this patch deletes the error
message. We already use polling mode to handle irq, but the
retry operation will render the polling weight inactive, this
patch just return budget when the rx is not completed to avoid
dead loop.
Fixes: 36eedfde1a36 ("net: hns: Optimize hns_nic_common_poll for better performance") Fixes: b5996f11ea54 ("net: add Hisilicon Network Subsystem basic ethernet support") Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
DSA subsystem takes care of netdev statistics since commit 4ed70ce9f01c
("net: dsa: Refactor transmit path to eliminate duplication"), so
any accounting inside tagger callbacks is redundant and can lead to
messing up the stats.
This bug is present in Qualcomm tagger since day 0.
Fixes: cafdc45c949b ("net-next: dsa: add Qualcomm tag RX/TX handler") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Alexander Lobakin <alobakin@dlink.ru> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
rndis_filter_device_add() allocates an instance of struct rndis_device
which never gets deallocated as rndis_filter_device_remove() sets
net_device->extension which points to the rndis_device struct to NULL,
leaving the rndis_device dangling.
Since net_device->extension is eventually freed in free_netvsc_device(),
we refrain from setting it to NULL inside rndis_filter_device_remove()
Signed-off-by: Mohammed Gamal <mgamal@redhat.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
I missed the fact that macvlan_broadcast() can be used both
in RX and TX.
skb_eth_hdr() makes only sense in TX paths, so we can not
use it blindly in macvlan_broadcast()
Fixes: 96cc4b69581d ("macvlan: do not assume mac_header is set in macvlan_broadcast()") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Jurgen Van Ham <juvanham@gmail.com> Tested-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The distributed arp table is using a DHT to store and retrieve MAC address
information for an IP address. This is done using unicast messages to
selected peers. The potential peers are looked up using the IP address and
the VID.
While the IP address is always stored in big endian byte order, this is not
the case of the VID. It can (depending on the host system) either be big
endian or little endian. The host must therefore always convert it to big
endian to ensure that all devices calculate the same peers for the same
lookup data.
Fixes: be1db4f6615b ("batman-adv: make the Distributed ARP Table vlan aware") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The driver was doing a synchronous uninterruptible bulk-transfer without
using a timeout. This could lead to the driver hanging on probe due to a
malfunctioning (or malicious) device until the device is physically
disconnected. While sleeping in probe the driver prevents other devices
connected to the same hub from being added to (or removed from) the bus.
An arbitrary limit of five seconds should be more than enough.
Fixes: dbafc28955fa ("NFC: pn533: don't send USB data off of the stack") Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
An earlier commit (1b789577f655060d98d20e,
"netfilter: arp_tables: init netns pointer in xt_tgchk_param struct")
fixed missing net initialization for arptables, but turns out it was
incomplete. We can get a very similar struct net NULL deref during
error unwinding:
map->members is freed by ip_set_free() right before using it in
mtype_ext_cleanup() again. So we just have to move it down.
Reported-by: syzbot+4c3cc6dbe7259dbf9054@syzkaller.appspotmail.com Fixes: 40cd63bf33b2 ("netfilter: ipset: Support extensions which need a per data destroy function") Acked-by: Jozsef Kadlecsik <kadlec@netfilter.org> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The fragments attached to a skb can be part of a compound page. In that case,
page_ref_inc will increment the refcount for the wrong page. Fix this by
using get_page instead, which calls page_ref_inc on the compound head and
also checks for overflow.
Fixes: 2b67f944f88c ("cfg80211: reuse existing page fragments in A-MSDU rx") Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20200113182107.20461-1-nbd@nbd.name Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Patch series "Fix two above-47bit hint address vs. THP bugs".
The two get_unmapped_area() implementations have to be fixed to provide
THP-friendly mappings if above-47bit hint address is specified.
This patch (of 2):
Filesystems use thp_get_unmapped_area() to provide THP-friendly
mappings. For DAX in particular.
Normally, the kernel doesn't create userspace mappings above 47-bit,
even if the machine allows this (such as with 5-level paging on x86-64).
Not all user space is ready to handle wide addresses. It's known that
at least some JIT compilers use higher bits in pointers to encode their
information.
Userspace can ask for allocation from full address space by specifying
hint address (with or without MAP_FIXED) above 47-bits. If the
application doesn't need a particular address, but wants to allocate
from whole address space it can specify -1 as a hint address.
Unfortunately, this trick breaks thp_get_unmapped_area(): the function
would not try to allocate PMD-aligned area if *any* hint address
specified.
Modify the routine to handle it correctly:
- Try to allocate the space at the specified hint address with length
padding required for PMD alignment.
- If failed, retry without length padding (but with the same hint
address);
- If the returned address matches the hint address return it.
- Otherwise, align the address as required for THP and return.
The user specified hint address is passed down to get_unmapped_area() so
above-47bit hint address will be taken into account without breaking
alignment requirements.
Link: http://lkml.kernel.org/r/20191220142548.7118-2-kirill.shutemov@linux.intel.com Fixes: b569bab78d8d ("x86/mm: Prepare to expose larger address space to userspace") Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reported-by: Thomas Willhalm <thomas.willhalm@intel.com> Tested-by: Dan Williams <dan.j.williams@intel.com> Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.vnet.ibm.com> Cc: "Bruggeman, Otto G" <otto.g.bruggeman@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Check for NULL port data in the shared interrupt and bulk completion
callbacks to avoid dereferencing a NULL pointer in case a device sends
data for a port device which isn't bound to a driver (e.g. due to a
malicious device having unexpected endpoints or after an allocation
failure on port probe).
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
XGMAC supports maximum MTU that can go to 16KB. Lets add this check in
the calculation of RX buffer size.
Fixes: 7ac6653a085b ("stmmac: Move the STMicroelectronics driver") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The 16KB RX Buffer must also be 16 byte aligned. Fix it.
Fixes: 7ac6653a085b ("stmmac: Move the STMicroelectronics driver") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Patch series "use div64_ul() instead of div_u64() if the divisor is
unsigned long".
We were first inspired by commit b0ab99e7736a ("sched: Fix possible divide
by zero in avg_atom () calculation"), then refer to the recently analyzed
mm code, we found this suspicious place.
201 if (min) {
202 min *= this_bw;
203 do_div(min, tot_bw);
204 }
And we also disassembled and confirmed it:
/usr/src/debug/kernel-4.9.168-016.ali3000/linux-4.9.168-016.ali3000.alios7.x86_64/mm/page-writeback.c: 201
0xffffffff811c37da <__wb_calc_thresh+234>: xor %r10d,%r10d
0xffffffff811c37dd <__wb_calc_thresh+237>: test %rax,%rax
0xffffffff811c37e0 <__wb_calc_thresh+240>: je 0xffffffff811c3800 <__wb_calc_thresh+272>
/usr/src/debug/kernel-4.9.168-016.ali3000/linux-4.9.168-016.ali3000.alios7.x86_64/mm/page-writeback.c: 202
0xffffffff811c37e2 <__wb_calc_thresh+242>: imul %r8,%rax
/usr/src/debug/kernel-4.9.168-016.ali3000/linux-4.9.168-016.ali3000.alios7.x86_64/mm/page-writeback.c: 203
0xffffffff811c37e6 <__wb_calc_thresh+246>: mov %r9d,%r10d ---> truncates it to 32 bits here
0xffffffff811c37e9 <__wb_calc_thresh+249>: xor %edx,%edx
0xffffffff811c37eb <__wb_calc_thresh+251>: div %r10
0xffffffff811c37ee <__wb_calc_thresh+254>: imul %rbx,%rax
0xffffffff811c37f2 <__wb_calc_thresh+258>: shr $0x2,%rax
0xffffffff811c37f6 <__wb_calc_thresh+262>: mul %rcx
0xffffffff811c37f9 <__wb_calc_thresh+265>: shr $0x2,%rdx
0xffffffff811c37fd <__wb_calc_thresh+269>: mov %rdx,%r10
This series uses div64_ul() instead of div_u64() if the divisor is
unsigned long, to avoid truncation to 32-bit on 64-bit platforms.
This patch (of 3):
The variables 'min' and 'max' are unsigned long and do_div truncates
them to 32 bits, which means it can test non-zero and be truncated to
zero for division. Fix this issue by using div64_ul() instead.
Link: http://lkml.kernel.org/r/20200102081442.8273-2-wenyang@linux.alibaba.com Fixes: 693108a8a667 ("writeback: make bdi->min/max_ratio handling cgroup writeback aware") Signed-off-by: Wen Yang <wenyang@linux.alibaba.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Qian Cai <cai@lca.pw> Cc: Tejun Heo <tj@kernel.org> Cc: Jens Axboe <axboe@kernel.dk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
(gdb) l *(btrfs_find_all_roots_safe+0x41)
0x8d7e1 is in btrfs_find_all_roots_safe (fs/btrfs/backref.c:1413).
1408
1409 tmp = ulist_alloc(GFP_NOFS);
1410 if (!tmp)
1411 return -ENOMEM;
1412 *roots = ulist_alloc(GFP_NOFS);
1413 if (!*roots) {
1414 ulist_free(tmp);
1415 return -ENOMEM;
1416 }
1417
Following the lifetime of the allocated 'roots' ulist, it gets freed
again in btrfs_qgroup_account_extent().
But this does not happen if the function is called with the
'BTRFS_FS_QUOTA_ENABLED' flag cleared, then btrfs_qgroup_account_extent()
does a short leave and directly returns.
Instead of directly returning we should jump to the 'out_free' in order to
free all resources as expected.
Shmem/tmpfs tries to provide THP-friendly mappings if huge pages are
enabled. But it doesn't work well with above-47bit hint address.
Normally, the kernel doesn't create userspace mappings above 47-bit,
even if the machine allows this (such as with 5-level paging on x86-64).
Not all user space is ready to handle wide addresses. It's known that
at least some JIT compilers use higher bits in pointers to encode their
information.
Userspace can ask for allocation from full address space by specifying
hint address (with or without MAP_FIXED) above 47-bits. If the
application doesn't need a particular address, but wants to allocate
from whole address space it can specify -1 as a hint address.
Unfortunately, this trick breaks THP alignment in shmem/tmp:
shmem_get_unmapped_area() would not try to allocate PMD-aligned area if
*any* hint address specified.
This can be fixed by requesting the aligned area if the we failed to
allocated at user-specified hint address. The request with inflated
length will also take the user-specified hint address. This way we will
not lose an allocation request from the full address space.
[kirill@shutemov.name: fold in a fixup] Link: http://lkml.kernel.org/r/20191223231309.t6bh5hkbmokihpfu@box Link: http://lkml.kernel.org/r/20191220142548.7118-3-kirill.shutemov@linux.intel.com Fixes: b569bab78d8d ("x86/mm: Prepare to expose larger address space to userspace") Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: "Willhalm, Thomas" <thomas.willhalm@intel.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: "Bruggeman, Otto G" <otto.g.bruggeman@intel.com> Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.vnet.ibm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We observed an issue that was some extra columns displayed after switching
perf data file in browser. The steps to reproduce:
1. perf record -a -e cycles,instructions -- sleep 3
2. perf report --group
3. In browser, we use hotkey 's' to switch to another perf.data
4. Now in browser, the extra columns 'Self' and 'Children' are displayed.
The issue is setup_sorting() executed again after repeat path, so dimensions
are added again.
This patch checks the last key returned from __cmd_report(). If it's
K_SWITCH_INPUT_DATA, skips the setup_sorting().
Fixes: ad0de0971b7f ("perf report: Enable the runtime switching of perf data file") Signed-off-by: Jin Yao <yao.jin@linux.intel.com> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Acked-by: Jiri Olsa <jolsa@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Feng Tang <feng.tang@intel.com> Cc: Jin Yao <yao.jin@intel.com> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/20191220013722.20592-1-yao.jin@linux.intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The EFI mixed mode entry code goes through the ordinary startup_32()
routine before jumping into the kernel's EFI boot code in 64-bit
mode. The 32-bit startup code must be entered with paging disabled,
but this is not documented as a requirement for the EFI handover
protocol, and so we should disable paging explicitly when entering
the kernel from 32-bit EFI firmware.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Cc: <stable@vger.kernel.org> Cc: Arvind Sankar <nivedita@alum.mit.edu> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Link: https://lkml.kernel.org/r/20191224132909.102540-4-ardb@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A system that supports resource monitoring may have multiple resources
while not all of these resources are capable of monitoring. Monitoring
related state is initialized only for resources that are capable of
monitoring and correspondingly this state should subsequently only be
removed from these resources that are capable of monitoring.
domain_add_cpu() calls domain_setup_mon_state() only when r->mon_capable
is true where it will initialize d->mbm_over. However,
domain_remove_cpu() calls cancel_delayed_work(&d->mbm_over) without
checking r->mon_capable resulting in an attempt to cancel d->mbm_over on
all resources, even those that never initialized d->mbm_over because
they are not capable of monitoring. Hence, it triggers a debugobjects
warning when offlining CPUs because those timer debugobjects are never
initialized:
ODEBUG: assert_init not available (active state 0) object type:
timer_list hint: 0x0
WARNING: CPU: 143 PID: 789 at lib/debugobjects.c:484
debug_print_object
Hardware name: HP Synergy 680 Gen9/Synergy 680 Gen9 Compute Module, BIOS I40 05/23/2018
RIP: 0010:debug_print_object
Call Trace:
debug_object_assert_init
del_timer
try_to_grab_pending
cancel_delayed_work
resctrl_offline_cpu
cpuhp_invoke_callback
cpuhp_thread_fun
smpboot_thread_fn
kthread
ret_from_fork
- D+ goes high, Host starts running by remote wakeup
- D+ is not stable, goes low
- Host requests GetPortStatus at (*1) and gets the following hub status:
- Current Connect Status bit is 0
- Connect Status Change bit is 1
- D+ stabilizes, goes high
- Host requests ClearPortFeature and thus Connect Status Change bit is
cleared at (*2)
- After waiting 100 ms, Host starts the Interrupt Transfer at (*3)
- Since the Connect Status Change bit is 0, Hub returns NAK.
In this case, port_event() is not called in hub_event() and Host cannot
recognize device. To solve this issue, flag change_bits even if only
Connect Status Change bit is 1 when got in the first GetPortStatus.
This issue occurs rarely because it only if D+ changes during a very
short time between GetPortStatus and ClearPortFeature. However, it is
fatal if it occurs in embedded system.
Commit 69f594a38967 ("ptrace: do not audit capability check when outputing /proc/pid/stat")
introduced the ability to opt out of audit messages for accesses to various
proc files since they are not violations of policy. While doing so it
somehow switched the check from ns_capable() to
has_ns_capability{_noaudit}(). That means it switched from checking the
subjective credentials of the task to using the objective credentials. This
is wrong since. ptrace_has_cap() is currently only used in
ptrace_may_access() And is used to check whether the calling task (subject)
has the CAP_SYS_PTRACE capability in the provided user namespace to operate
on the target task (object). According to the cred.h comments this would
mean the subjective credentials of the calling task need to be used.
This switches ptrace_has_cap() to use security_capable(). Because we only
call ptrace_has_cap() in ptrace_may_access() and in there we already have a
stable reference to the calling task's creds under rcu_read_lock() there's
no need to go through another series of dereferences and rcu locking done
in ns_capable{_noaudit}().
As one example where this might be particularly problematic, Jann pointed
out that in combination with the upcoming IORING_OP_OPENAT feature, this
bug might allow unprivileged users to bypass the capability checks while
asynchronously opening files like /proc/*/mem, because the capability
checks for this would be performed against kernel credentials.
To illustrate on the former point about this being exploitable: When
io_uring creates a new context it records the subjective credentials of the
caller. Later on, when it starts to do work it creates a kernel thread and
registers a callback. The callback runs with kernel creds for
ktask->real_cred and ktask->cred. To prevent this from becoming a
full-blown 0-day io_uring will call override_cred() and override
ktask->cred with the subjective credentials of the creator of the io_uring
instance. With ptrace_has_cap() currently looking at ktask->real_cred this
override will be ineffective and the caller will be able to open arbitray
proc files as mentioned above.
Luckily, this is currently not exploitable but will turn into a 0-day once
IORING_OP_OPENAT{2} land in v5.6. Fix it now!
Cc: Oleg Nesterov <oleg@redhat.com> Cc: Eric Paris <eparis@redhat.com> Cc: stable@vger.kernel.org Reviewed-by: Kees Cook <keescook@chromium.org> Reviewed-by: Serge Hallyn <serge@hallyn.com> Reviewed-by: Jann Horn <jannh@google.com> Fixes: 69f594a38967 ("ptrace: do not audit capability check when outputing /proc/pid/stat") Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Tom Hatskevich reported that we look up "iocp" then, in the called
functions we do a second copy_from_user() and look it up again.
The problem that could cause is:
drivers/message/fusion/mptctl.c
674 /* All of these commands require an interrupt or
675 * are unknown/illegal.
676 */
677 if ((ret = mptctl_syscall_down(iocp, nonblock)) != 0)
^^^^
We take this lock.
678 return ret;
679
680 if (cmd == MPTFWDOWNLOAD)
681 ret = mptctl_fw_download(arg);
^^^
Then the user memory changes and we look up "iocp" again but a different
one so now we are holding the incorrect lock and have a race condition.
682 else if (cmd == MPTCOMMAND)
683 ret = mptctl_mpt_command(arg);
The security impact of this bug is not as bad as it could have been
because these operations are all privileged and root already has
enormous destructive power. But it's still worth fixing.
This patch passes the "iocp" pointer to the functions to avoid the
second lookup. That deletes 100 lines of code from the driver so
it's a nice clean up as well.
Link: https://lore.kernel.org/r/20200114123414.GA7957@kadam Reported-by: Tom Hatskevich <tom2001tom.23@gmail.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
gcc -O3 warns that some local variables are not properly initialized:
drivers/scsi/fnic/vnic_dev.c: In function 'fnic_dev_hang_notify':
drivers/scsi/fnic/vnic_dev.c:511:16: error: 'a0' is used uninitialized in this function [-Werror=uninitialized]
vdev->args[0] = *a0;
~~~~~~~~~~~~~~^~~~~
drivers/scsi/fnic/vnic_dev.c:691:6: note: 'a0' was declared here
u64 a0, a1;
^~
drivers/scsi/fnic/vnic_dev.c:512:16: error: 'a1' is used uninitialized in this function [-Werror=uninitialized]
vdev->args[1] = *a1;
~~~~~~~~~~~~~~^~~~~
drivers/scsi/fnic/vnic_dev.c:691:10: note: 'a1' was declared here
u64 a0, a1;
^~
drivers/scsi/fnic/vnic_dev.c: In function 'fnic_dev_mac_addr':
drivers/scsi/fnic/vnic_dev.c:512:16: error: 'a1' is used uninitialized in this function [-Werror=uninitialized]
vdev->args[1] = *a1;
~~~~~~~~~~~~~~^~~~~
drivers/scsi/fnic/vnic_dev.c:698:10: note: 'a1' was declared here
u64 a0, a1;
^~
Apparently the code relies on the local variables occupying adjacent memory
locations in the same order, but this is of course not guaranteed.
Use an array of two u64 variables where needed to make it work correctly.
I suspect there is also an endianness bug here, but have not digged in deep
enough to be sure.
Fixes: 5df6d737dd4b ("[SCSI] fnic: Add new Cisco PCI-Express FCoE HBA") Fixes: mmtom ("init/Kconfig: enable -O3 for all arches") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200107201602.4096790-1-arnd@arndb.de Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>