Tx99 is typically configured via a monitor mode interface, which does
not get added to the driver as a vif. Since the code currently expects
a configured virtual interface for tx99, enabling tx99 via debugfs fails.
Since the vif is not needed anyway, remove all checks for it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[kvalo@codeaurora.org: s/CPTCFG/CONFIG/] Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When REGULATORY_COUNTRY_IE_IGNORE is set, __reg_process_hint_country_ie()
ignores the country code change request from __cfg80211_connect_result()
via regulatory_hint_country_ie().
After Disconnect, similar to above, country code should not be reset to
world when country IE ignore is set. But this is violated and restore of
regulatory settings is invoked by cfg80211_disconnect_work via
regulatory_hint_disconnect().
To address this, avoid regulatory restore from regulatory_hint_disconnect()
when COUNTRY_IE_IGNORE is set.
Note: Currently, restore_regulatory_settings() takes care of clearing
beacon hints. But in the proposed change, regulatory restore is avoided.
Therefore, explicitly clear beacon hints when DISABLE_BEACON_HINTS
is not set.
When we have first case to fall through it's not enough to put
single comment there to satisfy compiler. Instead of doing that,
return fall back value directly from default case.
This to avoid following warnings:
drivers/extcon/extcon-intel-cht-wc.c: In function ‘cht_wc_extcon_get_charger’:
include/linux/device.h:1420:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
_dev_warn(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/extcon/extcon-intel-cht-wc.c:148:3: note: in expansion of macro ‘dev_warn’
dev_warn(ext->dev,
^~~~~~~~
drivers/extcon/extcon-intel-cht-wc.c:152:2: note: here
case CHT_WC_USBSRC_TYPE_SDP:
^~~~
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
According to the NanoPi-A64 schematics, DCDC1 is connected to a voltage
rail named "VDD_SYS_3.3V". All users seem to expect 3.3V here: the
Ethernet PHY, the uSD card slot, the camera interface and the GPIO pins
on the headers.
Fix up the voltage on the regulator to lift it up to 3.3V.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The Olinuxino board uses DDR3L chips which are supposed to be driven
with 1.35V. The reset default of the AXP is properly set to 1.36V.
While technically the chips can also run at 1.5 volts, changing the
voltage on the fly while booting Linux is asking for trouble. Also
running at a lower voltage saves power.
So fix the DCDC5 value to match the actual board design.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Tested-by: Martin Lucina <martin@lucina.net> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In the above scenario, CE buffer entries will be freed up and become NULL in
ath10k_pci_flush. And the napi_poll has been invoked after the flush process
and it will try to get the skb from the CE buffer entry and perform some action on that.
Since the CE buffer already cleaned by pci flush this action will create NULL
pointer dereference and trigger below kernel panic.
Unable to handle kernel NULL pointer dereference at virtual address 0000005c
PC is at ath10k_pci_htt_rx_cb+0x64/0x3ec [ath10k_pci]
ath10k_pci_htt_rx_cb [ath10k_pci]
ath10k_ce_per_engine_service+0x74/0xc4 [ath10k_pci]
ath10k_ce_per_engine_service [ath10k_pci]
ath10k_ce_per_engine_service_any+0x74/0x80 [ath10k_pci]
ath10k_ce_per_engine_service_any [ath10k_pci]
ath10k_pci_napi_poll+0x48/0xec [ath10k_pci]
ath10k_pci_napi_poll [ath10k_pci]
net_rx_action+0xac/0x160
net_rx_action
__do_softirq+0xdc/0x208
__do_softirq
irq_exit+0x84/0xe0
irq_exit
__handle_domain_irq+0x80/0xa0
__handle_domain_irq
gic_handle_irq+0x38/0x5c
gic_handle_irq
__irq_usr+0x44/0x60
Tested on QCA4019 and firmware version 10.4.3.2.1.1-00010
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
DT nodes may have a 'status' property which, if set to anything other
than 'ok' or 'okay', indicates to the OS that the DT node should be
treated as if it was not present. So add that missing logic to the
OP-TEE driver.
After finding a reasonable gain, the function converts the configured
gain to a gain configuration option selector enum max9611_csa_gain.
Make the conversion clearly visible by using an explicit cast. This
also avoids a warning seen with clang:
drivers/iio/adc/max9611.c:292:16: warning: implicit conversion from
enumeration type 'enum max9611_conf_ids' to different enumeration
type 'enum max9611_csa_gain' [-Wenum-conversion]
*csa_gain = gain_selectors[i];
~ ^~~~~~~~~~~~~~~~~
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The quirks2 are parsed and set (e.g. from DT) before the quirk for broken
HS200 is set in the driver.
The driver needs to enable just this flag, not rewrite the whole quirk set.
Fixes: 7871aa60ae00 ("mmc: sdhci-of-at91: add quirk for broken HS200") Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
An exiting task might belong to an offline cgroup. In this case an
attempt to grab a cgroup reference from the task can end up with an
infinite loop in hugetlb_cgroup_charge_cgroup(), because neither the
cgroup will become online, neither the task will be migrated to a live
cgroup.
Fix this by switching over to css_tryget(). As css_tryget_online()
can't guarantee that the cgroup won't go offline, in most cases the
check doesn't make sense. In this particular case users of
hugetlb_cgroup_charge_cgroup() are not affected by this change.
A similar problem is described by commit 18fa84a2db0e ("cgroup: Use
css_tryget() instead of css_tryget_online() in task_get_css()").
Link: http://lkml.kernel.org/r/20191106225131.3543616-2-guro@fb.com Signed-off-by: Roman Gushchin <guro@fb.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Tejun Heo <tj@kernel.org> Reviewed-by: Shakeel Butt <shakeelb@google.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We've encountered a rcu stall in get_mem_cgroup_from_mm():
rcu: INFO: rcu_sched self-detected stall on CPU
rcu: 33-....: (21000 ticks this GP) idle=6c6/1/0x4000000000000002 softirq=35441/35441 fqs=5017
(t=21031 jiffies g=324821 q=95837) NMI backtrace for cpu 33
<...>
RIP: 0010:get_mem_cgroup_from_mm+0x2f/0x90
<...>
__memcg_kmem_charge+0x55/0x140
__alloc_pages_nodemask+0x267/0x320
pipe_write+0x1ad/0x400
new_sync_write+0x127/0x1c0
__kernel_write+0x4f/0xf0
dump_emit+0x91/0xc0
writenote+0xa0/0xc0
elf_core_dump+0x11af/0x1430
do_coredump+0xc65/0xee0
get_signal+0x132/0x7c0
do_signal+0x36/0x640
exit_to_usermode_loop+0x61/0xd0
do_syscall_64+0xd4/0x100
entry_SYSCALL_64_after_hwframe+0x44/0xa9
The problem is caused by an exiting task which is associated with an
offline memcg. We're iterating over and over in the do {} while
(!css_tryget_online()) loop, but obviously the memcg won't become online
and the exiting task won't be migrated to a live memcg.
Let's fix it by switching from css_tryget_online() to css_tryget().
As css_tryget_online() cannot guarantee that the memcg won't go offline,
the check is usually useless, except some rare cases when for example it
determines if something should be presented to a user.
A similar problem is described by commit 18fa84a2db0e ("cgroup: Use
css_tryget() instead of css_tryget_online() in task_get_css()").
Johannes:
: The bug aside, it doesn't matter whether the cgroup is online for the
: callers. It used to matter when offlining needed to evacuate all charges
: from the memcg, and so needed to prevent new ones from showing up, but we
: don't care now.
Link: http://lkml.kernel.org/r/20191106225131.3543616-1-guro@fb.com Signed-off-by: Roman Gushchin <guro@fb.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Tejun Heo <tj@kernel.org> Reviewed-by: Shakeel Butt <shakeeb@google.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Michal Koutn <mkoutny@suse.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For both PASID-based-Device-TLB Invalidate Descriptor and
Device-TLB Invalidate Descriptor, the Physical Function Source-ID
value is split according to this layout:
PFSID[3:0] is set at offset 12 and PFSID[15:4] is put at offset 52.
Fix the part laid out at offset 52.
Fixes: 0f725561e1684 ("iommu/vt-d: Add definitions for PFSID") Signed-off-by: Eric Auger <eric.auger@redhat.com> Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Cc: stable@vger.kernel.org # v4.19+ Acked-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We need to get the underlying dentry of parent; sure, absent the races
it is the parent of underlying dentry, but there's nothing to prevent
losing a timeslice to preemtion in the middle of evaluation of
lower_dentry->d_parent->d_inode, having another process move lower_dentry
around and have its (ex)parent not pinned anymore and freed on memory
pressure. Then we regain CPU and try to fetch ->d_inode from memory
that is freed by that point.
dentry->d_parent *is* stable here - it's an argument of ->lookup() and
we are guaranteed that it won't be moved anywhere until we feed it
to d_add/d_splice_alias. So we safely go that way to get to its
underlying dentry.
Cc: stable@vger.kernel.org # since 2009 or so Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
lower_dentry can't go from positive to negative (we have it pinned),
but it *can* go from negative to positive. So fetching ->d_inode
into a local variable, doing a blocking allocation, checking that
now ->d_inode is non-NULL and feeding the value we'd fetched
earlier to a function that won't accept NULL is not a good idea.
Cc: stable@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Many cheap devices use Silead touchscreen controllers. Testing has shown
repeatedly that these touchscreen controllers work fine at 400KHz, but for
unknown reasons do not work properly at 100KHz. This has been seen on
both ARM and x86 devices using totally different i2c controllers.
On some devices the ACPI tables list another device at the same I2C-bus
as only being capable of 100KHz, testing has shown that these other
devices work fine at 400KHz (as can be expected of any recent I2C hw).
This commit makes i2c_acpi_find_bus_speed() always return 400KHz if a
Silead touchscreen controller is present, fixing the touchscreen not
working on devices which ACPI tables' wrongly list another device on the
same bus as only being capable of 100KHz.
Specifically this fixes the touchscreen on the Jumper EZpad 6 m4 not
working.
Reported-by: youling 257 <youling257@gmail.com> Tested-by: youling 257 <youling257@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[wsa: rewording warning a little] Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If an hfi1 card is inserted in a Gen4 systems, the driver will avoid the
gen3 speed bump and the card will operate at half speed.
This is because the driver avoids the gen3 speed bump when the parent bus
speed isn't identical to gen3, 8.0GT/s. This is not compatible with gen4
and newer speeds.
Fix by relaxing the test to explicitly look for the lower capability
speeds which inherently allows for gen4 and all future speeds.
Fixes: 7724105686e7 ("IB/hfi1: add driver files") Link: https://lore.kernel.org/r/20191101192059.106248.1699.stgit@awfm-01.aw.intel.com Cc: <stable@vger.kernel.org> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Reviewed-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: James Erwin <james.erwin@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The driver for F54 just polls the status and doesn't even have a IRQ
handler registered. Make sure to disable all F54 IRQs, so we don't crash
the kernel on a nonexistent handler.
Currently, rmi_f11_attention() and rmi_f12_attention() functions update
the attn_data data pointer and size based on the size of the expected
size of the attention data. However, if the actual valid data in the
attn buffer is less then the expected value then the updated data
pointer will point to memory beyond the end of the attn buffer. Using
the calculated valid_bytes instead will prevent this from happening.
This patch fixes an issue seen on HID touchpads which report finger
positions using RMI4 Function 12. The issue manifests itself as
spurious button presses as described in:
https://www.spinics.net/lists/linux-input/msg58618.html
Commit 24d28e4f1271 ("Input: synaptics-rmi4 - convert irq distribution
to irq_domain") switched the RMI4 driver to using an irq_domain to handle
RMI4 function interrupts. Functions with more then one interrupt now have
each interrupt mapped to their own IRQ and IRQ handler. The result of
this change is that the F12 IRQ handler was now getting called twice. Once
for the absolute data interrupt and once for the relative data interrupt.
For HID devices, calling rmi_f12_attention() a second time causes the
attn_data data pointer and size to be set incorrectly. When the touchpad
button is pressed, F30 will generate an interrupt and attempt to read the
F30 data from the invalid attn_data data pointer and report incorrect
button events.
This patch disables the F12 relative interrupt which prevents
rmi_f12_attention() from being called twice.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com> Reported-by: Simon Wood <simon@mungewell.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20191025002527.3189-2-aduggan@synaptics.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The video buffer used by the queue is a vb2_v4l2_buffer, not a plain
vb2_buffer. Using the wrong type causes the allocation of the buffer
storage to be too small, causing a out of bounds write when
__init_vb2_v4l2_buffer initializes the buffer.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Fixes: 3a762dbd5347 ("[media] Input: synaptics-rmi4 - add support for F54 diagnostics") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20191104114454.10500-1-l.stach@pengutronix.de Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
While output urb's snd_complete_urb() is executing, calling
prepare_outbound_urb() may cause endpoint stopped before
prepare_outbound_urb() returns and result in next urb submitted
to stopped endpoint. usb-audio driver cannot re-use it afterwards as
the urb is still hold by usb stack.
This change checks EP_FLAG_RUNNING flag after prepare_outbound_urb() again
to let snd_complete_urb() know the endpoint already stopped and does not
submit next urb. Below kind of error will be fixed:
[ 213.153103] usb 1-2: timeout: still 1 active urbs on EP #1
[ 213.164121] usb 1-2: cannot submit urb 0, error -16: unknown error
Signed-off-by: Henry Lin <henryl@nvidia.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191113021420.13377-1-henryl@nvidia.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A check of the return value from get_cur_mix_raw() is missing at the
resolution test code in get_min_max_with_quirks(), which may leave the
variable untouched, leading to a random uninitialized value, as
detected by syzkaller fuzzer.
Add the missing return error check for fixing that.
Driver/net/can/slcan.c is derived from slip.c. Memory leak was detected
by Syzkaller in slcan. Same issue exists in slip.c and this patch is
addressing the leak in slip.c.
Here is the slcan memory leak trace reported by Syzkaller:
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If a malicious device gives a short MAC it can elicit up to
5 bytes of leaked memory out of the driver. We need to check for
ETH_ALEN instead.
Reported-by: syzbot+a8d4acdad35e6bbca308@syzkaller.appspotmail.com Signed-off-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
That change should have had a fixes tag for
commit 24d28e4f1271 ("Input: synaptics-rmi4 - convert irq distribution to
irq_domain"). The conversion to irq_domain introduced the issue being
fixed by this commit.
In older kernels the bitmap IRQ accounting is done differently, and
it doesn't suffer from the same issue of calling handle_nested_irq(0).
Keeping this commit on kernels 4.14 and older causes problems with
touchpads due to the different semantics of the IRQ bitmasks.
Signed-off-by: Evan Green <evgreen@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In scsi_mq_setup_tags(), cmd_size is calculated based on zero size for the
scatter-gather list in case the low level driver uses SG_NONE in its host
template.
cmd_size is passed on to the block layer for calculation of the request
size, and we've seen NULL pointer dereference errors from the block layer
in drivers where SG_NONE is used and a mq IO scheduler is active,
apparently as a consequence of this (see commit 68ab2d76e4be ("scsi:
cxlflash: Set sg_tablesize to 1 instead of SG_NONE"), and a recent patch by
Finn Thain converting the three m68k NFR5380 drivers to avoid setting
SG_NONE).
Try to avoid these errors by accounting for at least one sg list entry when
calculating cmd_size, regardless of whether the low level driver set a zero
sg_tablesize.
Tested on 030 m68k with the atari_scsi driver - setting sg_tablesize to
SG_NONE no longer results in a crash when loading this driver.
CC: Finn Thain <fthain@telegraphics.com.au> Link: https://lore.kernel.org/r/1572922150-4358-1-git-send-email-schmitzmic@gmail.com Signed-off-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The Ethernet Switch core mask was set to 0, causing the switch core to
be not reset on BCM6368 on boot. Provide the proper mask so the switch
core gets reset to a known good state.
Fixes: 799faa626c71 ("MIPS: BCM63XX: add core reset helper") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: linux-mips@vger.kernel.org Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Checking for 32-bit PAE is quite common around code that fiddles with
the PDPTRs. Add a function to compress all checks into a single
invocation.
Moving to the common helper also fixes a subtle bug in kvm_set_cr3()
where it fails to check is_long_mode() and results in KVM incorrectly
attempting to load PDPTRs for a 64-bit guest.
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[sean: backport to 4.x; handle vmx.c split in 5.x, call out the bugfix] Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The "42f5cda5eaf4" commit rightly set SOCK_DONE on peer shutdown,
but there is an issue if we receive the SHUTDOWN(RDWR) while the
virtio_transport_close_timeout() is scheduled.
In this case, when the timeout fires, the SOCK_DONE is already
set and the virtio_transport_close_timeout() will not call
virtio_transport_reset() and virtio_transport_do_close().
This causes that both sockets remain open and will never be released,
preventing the unloading of [virtio|vhost]_transport modules.
This patch fixes this issue, calling virtio_transport_reset() and
virtio_transport_do_close() when we receive the SHUTDOWN(RDWR)
and there is nothing left to read.
Fixes: 42f5cda5eaf4 ("vsock/virtio: set SOCK_DONE on peer shutdown") Cc: Stephen Barber <smbarber@chromium.org> Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Same as commit 1b4a75108d5b ("netfilter: ipset: Copy the right MAC
address in bitmap:ip,mac and hash:ip,mac sets"), another copy and paste
went wrong in commit 8cc4ccf58379 ("netfilter: ipset: Allow matching on
destination MAC address for mac and ipmac sets").
When I fixed this for IPv4 in 1b4a75108d5b, I didn't realise that
hash:ip,mac sets also support IPv6 as family, and this is covered by a
separate function, hash_ipmac6_kadt().
In hash:ip,mac sets, the first dimension is the IP address, and the
second dimension is the MAC address: check the IPSET_DIM_TWO_SRC flag
in flags while deciding which MAC address to copy, destination or
source.
This way, mixing source and destination matches for the two dimensions
of ip,mac hash type works as expected, also for IPv6. With this setup:
ip netns add A
ip link add veth1 type veth peer name veth2 netns A
ip addr add 2001:db8::1/64 dev veth1
ip -net A addr add 2001:db8::2/64 dev veth2
ip link set veth1 up
ip -net A link set veth2 up
dst=$(ip netns exec A cat /sys/class/net/veth2/address)
ip netns exec A ipset create test_hash hash:ip,mac family inet6
ip netns exec A ipset add test_hash 2001:db8::1,${dst}
ip netns exec A ip6tables -A INPUT -p icmpv6 --icmpv6-type 135 -j ACCEPT
ip netns exec A ip6tables -A INPUT -m set ! --match-set test_hash src,dst -j DROP
ipset now correctly matches a test packet:
# ping -c1 2001:db8::2 >/dev/null
# echo $?
0
Reported-by: Chen, Yi <yiche@redhat.com> Fixes: 8cc4ccf58379 ("netfilter: ipset: Allow matching on destination MAC address for mac and ipmac sets") Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 03c4749dd6c7 ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux
GPIO translation") has made the cherryview gpio numbers sparse, to get
a 1:1 mapping between ACPI pin numbers and gpio numbers in Linux.
This has greatly simplified things, but the code setting the
irq_valid_mask was not updated for this, so the valid mask is still in
the old "compressed" numbering with the gaps in the pin numbers skipped,
which is wrong as irq_valid_mask needs to be expressed in gpio numbers.
This results in the following error on devices using pin 24 (0x0018) on
the north GPIO controller as an ACPI event source:
[ 0.422452] cherryview-pinctrl INT33FF:01: Failed to translate GPIO to IRQ
This has been reported (by email) to be happening on a Caterpillar CAT T20
tablet and I've reproduced this myself on a Medion Akoya e2215t 2-in-1.
This commit uses the pin number instead of the compressed index into
community->pins to clear the correct bits in irq_valid_mask for GPIOs
using GPEs for interrupts, fixing these errors and in case of the
Medion Akoya e2215t also fixing the LID switch not working.
Cc: stable@vger.kernel.org Fixes: 03c4749dd6c7 ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux GPIO translation") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When consumer requests a pin, in order to be on the safest side,
we switch it first to GPIO mode followed by immediate transition
to the input state. Due to posted writes it's luckily to be a single
I/O transaction.
However, if firmware or boot loader already configures the pin
to the GPIO mode, user expects no glitches for the requested pin.
We may check if the pin is pre-configured and leave it as is
till the actual consumer toggles its state to avoid glitches.
Fixes: 7981c0015af2 ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Depends-on: f5a26acf0162 ("pinctrl: intel: Initialize GPIO properly when used through irqchip") Cc: stable@vger.kernel.org Cc: fei.yang@intel.com Reported-by: Oliver Barta <oliver.barta@aptiv.com> Reported-by: Malin Jonsson <malin.jonsson@ericsson.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When a GPIO is requested using gpiod_get_* APIs the intel pinctrl driver
switches the pin to GPIO mode and makes sure interrupts are routed to
the GPIO hardware instead of IOAPIC. However, if the GPIO is used
directly through irqchip, as is the case with many I2C-HID devices where
I2C core automatically configures interrupt for the device, the pin is
not initialized as GPIO. Instead we rely that the BIOS configures the
pin accordingly which seems not to be the case at least in Asus X540NA
SKU3 with Focaltech touchpad.
When the pin is not properly configured it might result weird behaviour
like interrupts suddenly stop firing completely and the touchpad stops
responding to user input.
Fix this by properly initializing the pin to GPIO mode also when it is
used directly through irqchip.
Fixes: 7981c0015af2 ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support") Reported-by: Daniel Drake <drake@endlessm.com> Reported-and-tested-by: Chris Chiu <chiu@endlessm.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
[WHY]
i2c_read is called to differentiate passive DP->HDMI and DP->DVI-D dongles
The call is expected to fail in DVI-D case but pass in HDMI case
Some HDMI dongles have a chance to fail as well, causing misdetection as DVI-D
[HOW]
Retry i2c_read to ensure failed result is valid
Signed-off-by: Michael Strauss <michael.strauss@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The events in the same group don't start or stop simultaneously.
Here is the ftrace when enabling event group for uncore_iio_0:
# perf stat -e "{uncore_iio_0/event=0x1/,uncore_iio_0/event=0xe/}"
<idle>-0 [000] d.h. 8959.064832: read_msr: a41, value b2b0b030 //Read counter reg of IIO unit0 counter0
<idle>-0 [000] d.h. 8959.064835: write_msr: a48, value
400001 //Write Ctrl reg of IIO unit0 counter0 to enable
counter0. <------ Although counter0 is enabled, Unit Ctrl is still
freezed. Nothing will count. We are still good here.
<idle>-0 [000] d.h. 8959.064836: read_msr: a40, value
30100 //Read Unit Ctrl reg of IIO unit0
<idle>-0 [000] d.h. 8959.064838: write_msr: a40, value
30000 //Write Unit Ctrl reg of IIO unit0 to enable all
counters in the unit by clear Freeze bit <------Unit0 is un-freezed.
Counter0 has been enabled. Now it starts counting. But counter1 has not
been enabled yet. The issue starts here.
<idle>-0 [000] d.h. 8959.064846: read_msr: a42, value 0
//Read counter reg of IIO unit0 counter1
<idle>-0 [000] d.h. 8959.064847: write_msr: a49, value
40000e //Write Ctrl reg of IIO unit0 counter1 to enable
counter1. <------ Now, counter1 just starts to count. Counter0 has
been running for a while.
Current code un-freezes the Unit Ctrl right after the first counter is
enabled. The subsequent group events always loses some counter values.
Implement pmu_enable and pmu_disable support for uncore, which can help
to batch hardware accesses.
No one uses uncore_enable_box and uncore_disable_box. Remove them.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: linux-drivers-review@eclists.intel.com Cc: linux-perf@eclists.intel.com Fixes: 087bfbb03269 ("perf/x86: Add generic Intel uncore PMU support") Link: https://lkml.kernel.org/r/1572014593-31591-1-git-send-email-kan.liang@linux.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
pass_accept_req() is using the same skb for handling accept request and
sending accept reply to HW. Here req and rpl structures are pointing to
same skb->data which is over written by INIT_TP_WR() and leads to
accessing corrupt req fields in accept_cr() while checking for ECN flags.
Reordered code in accept_cr() to fetch correct req fields.
Fixes: 92e7ae7172 ("iw_cxgb4: Choose appropriate hw mtu index and ISS for iWARP connections") Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com> Link: https://lore.kernel.org/r/20191003104353.11590-1-bharat@chelsio.com Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If we terminate the channel to free all descriptors associated with this
channel, we will leak the memory of current descriptor if the current
descriptor is not completed, since it had been deteled from the desc_issued
list and have not been added into the desc_completed list.
Thus we should check if current descriptor is completed or not, when freeing
the descriptors associated with one channel, if not, we should free it to
avoid this issue.
Fixes: 9b3b8171f7f4 ("dmaengine: sprd: Add Spreadtrum DMA driver") Reported-by: Zhenfang Wang <zhenfang.wang@unisoc.com> Tested-by: Zhenfang Wang <zhenfang.wang@unisoc.com> Signed-off-by: Baolin Wang <baolin.wang@linaro.org> Link: https://lore.kernel.org/r/170dbbc6d5366b6fa974ce2d366652e23a334251.1570609788.git.baolin.wang@linaro.org Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When the client hits a network reconnect, it re-opens every open
file with a create context to reconnect a persistent handle. All
create context types should be 8-bytes aligned but the padding
was missed for that one. As a result, some servers don't allow
us to reconnect handles and return an error. The problem occurs
when the problematic context is not at the end of the create
request packet. Fix this by adding a proper padding at the end
of the reconnect persistent handle context.
Cc: Stable <stable@vger.kernel.org> # 4.19.x Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Deferred memory initialisation updates zone->managed_pages during the
initialisation phase but before that finishes, the per-cpu page
allocator (pcpu) calculates the number of pages allocated/freed in
batches as well as the maximum number of pages allowed on a per-cpu
list. As zone->managed_pages is not up to date yet, the pcpu
initialisation calculates inappropriately low batch and high values.
This increases zone lock contention quite severely in some cases with
the degree of severity depending on how many CPUs share a local zone and
the size of the zone. A private report indicated that kernel build
times were excessive with extremely high system CPU usage. A perf
profile indicated that a large chunk of time was lost on zone->lock
contention.
This patch recalculates the pcpu batch and high values after deferred
initialisation completes for every populated zone in the system. It was
tested on a 2-socket AMD EPYC 2 machine using a kernel compilation
workload -- allmodconfig and all available CPUs.
mmtests configuration: config-workload-kernbench-max Configuration was
modified to build on a fresh XFS partition.
accompanied by an increase in machines going completely radio silent
under memory pressure.
One thing that changed since 4.16 is e699e2c6a654 ("net, mm: account
sock objects to kmemcg"), which made these slab caches subject to cgroup
memory accounting and control.
The problem with that is that cgroups, unlike the page allocator, do not
maintain dedicated atomic reserves. As a cgroup's usage hovers at its
limit, atomic allocations - such as done during network rx - can fail
consistently for extended periods of time. The kernel is not able to
operate under these conditions.
We don't want to revert the culprit patch, because it indeed tracks a
potentially substantial amount of memory used by a cgroup.
We also don't want to implement dedicated atomic reserves for cgroups.
There is no point in keeping a fixed margin of unused bytes in the
cgroup's memory budget to accomodate a consumer that is impossible to
predict - we'd be wasting memory and get into configuration headaches,
not unlike what we have going with min_free_kbytes. We do this for
physical mem because we have to, but cgroups are an accounting game.
Instead, account these privileged allocations to the cgroup, but let
them bypass the configured limit if they have to. This way, we get the
benefits of accounting the consumed memory and have it exert pressure on
the rest of the cgroup, but like with the page allocator, we shift the
burden of reclaimining on behalf of atomic allocations onto the regular
allocations that can block.
Link: http://lkml.kernel.org/r/20191022233708.365764-1-hannes@cmpxchg.org Fixes: e699e2c6a654 ("net, mm: account sock objects to kmemcg") Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reviewed-by: Shakeel Butt <shakeelb@google.com> Cc: Suleiman Souhlal <suleiman@google.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: <stable@vger.kernel.org> [4.18+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This patch fixes the problem of the spin locks, originally
meant for the netpoll path of hns driver, causing deadlock in
the normal NAPI poll path. The issue happened due to the presence
of the stray leftover spin lock code related to the netpoll,
whose support was earlier removed from the HNS[1], got activated
due to enabling of NET_POLL_CONTROLLER switch.
Earlier background:
The netpoll handling code originally had this bug(as identified
by Marc Zyngier[2]) of wrong spin lock API being used which did
not disable the interrupts and hence could cause locking issues.
i.e. if the lock were first acquired in context to thread like
'ip' util and this lock if ever got later acquired again in
context to the interrupt context like TX/RX (Interrupts could
always pre-empt the lock holding task and acquire the lock again)
and hence could cause deadlock.
Proposed Solution:
1. If the netpoll was enabled in the HNS driver, which is not
right now, we could have simply used spin_[un]lock_irqsave()
2. But as netpoll is disabled, therefore, it is best to get rid
of the existing locks and stray code for now. This should
solve the problem reported by Marc.
Fixes: 4bd2c03be707 ("net: hns: remove ndo_poll_controller") Cc: lipeng <lipeng321@huawei.com> Cc: Yisen Zhuang <yisen.zhuang@huawei.com> Cc: Eric Dumazet <edumazet@google.com> Cc: David S. Miller <davem@davemloft.net> Reported-by: Marc Zyngier <maz@kernel.org> Acked-by: Marc Zyngier <maz@kernel.org> Tested-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For new IBRS_ALL CPUs, the Enhanced IBRS check at the beginning of
cpu_bugs_smt_update() causes the function to return early, unintentionally
skipping the MDS and TAA logic.
This is not a problem for MDS, because there appears to be no overlap
between IBRS_ALL and MDS-affected CPUs. So the MDS mitigation would be
disabled and nothing would need to be done in this function anyway.
But for TAA, the TAA_MSG_SMT string will never get printed on Cascade
Lake and newer.
The check is superfluous anyway: when 'spectre_v2_enabled' is
SPECTRE_V2_IBRS_ENHANCED, 'spectre_v2_user' is always
SPECTRE_V2_USER_NONE, and so the 'spectre_v2_user' switch statement
handles it appropriately by doing nothing. So just remove the check.
iso_buffer should be set to NULL after use and free in the while loop.
In the case of isochronous URB in the while loop, iso_buffer is
allocated and after sending it to server, buffer is deallocated. And
then, if the next URB in the while loop is not a isochronous pipe,
iso_buffer still holds the previously deallocated buffer address and
kfree tries to free wrong buffer address.
Fixes: ea44d190764b ("usbip: Implement SG support to vhci-hcd and stub driver") Reported-by: kbuild test robot <lkp@intel.com> Reported-by: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: Suwan Kim <suwan.kim027@gmail.com> Reviewed-by: Julia Lawall <julia.lawall@lip6.fr> Acked-by: Shuah Khan <skhan@linuxfoundation.org> Link: https://lore.kernel.org/r/20191022093017.8027-1-suwan.kim027@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
cgroup writeback tries to refresh the associated wb immediately if the
current wb is dead. This is to avoid keeping issuing IOs on the stale
wb after memcg - blkcg association has changed (ie. when blkcg got
disabled / enabled higher up in the hierarchy).
Unfortunately, the logic gets triggered spuriously on inodes which are
associated with dead cgroups. When the logic is triggered on dead
cgroups, the attempt fails only after doing quite a bit of work
allocating and initializing a new wb.
While c3aab9a0bd91 ("mm/filemap.c: don't initiate writeback if mapping
has no dirty pages") alleviated the issue significantly as it now only
triggers when the inode has dirty pages. However, the condition can
still be triggered before the inode is switched to a different cgroup
and the logic simply doesn't make sense.
Skip the immediate switching if the associated memcg is dying.
This is a simplified version of the following two patches:
Functions like filemap_write_and_wait_range() should do nothing if inode
has no dirty pages or pages currently under writeback. But they anyway
construct struct writeback_control and this does some atomic operations if
CONFIG_CGROUP_WRITEBACK=y - on fast path it locks inode->i_lock and
updates state of writeback ownership, on slow path might be more work.
Current this path is safely avoided only when inode mapping has no pages.
For example generic_file_read_iter() calls filemap_write_and_wait_range()
at each O_DIRECT read - pretty hot path.
This patch skips starting new writeback if mapping has no dirty tags set.
If writeback is already in progress filemap_write_and_wait_range() will
wait for it.
Link: http://lkml.kernel.org/r/156378816804.1087.8607636317907921438.stgit@buzz Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Tejun Heo <tj@kernel.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The ECC (memory error detection and correction) mechanism can be
activated or not, controlled by the ECCDIS bit in CAN_MECR. When
disabled, updates on indications and reporting registers are stopped.
So if want to disable ECC completely, had better assert ECCDIS bit, not
just mask the related interrupts.
Fixes: cdce844865be ("can: flexcan: add vf610 support for FlexCAN") Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The removal of the LDR initialization in the bigsmp_32 APIC code unearthed
a problem in setup_local_APIC().
The code checks unconditionally for a mismatch of the logical APIC id by
comparing the early APIC id which was initialized in get_smp_config() with
the actual LDR value in the APIC.
Due to the removal of the bogus LDR initialization the check now can
trigger on bigsmp_32 APIC systems emitting a warning for every booting
CPU. This is of course a false positive because the APIC is not using
logical destination mode.
Restrict the check and the possibly resulting fixup to systems which are
actually using the APIC in logical destination mode.
[ tglx: Massaged changelog and added Cc stable ]
Fixes: bae3a8d3308 ("x86/apic: Do not initialize LDR and DFR for bigsmp") Signed-off-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/666d8f91-b5a8-1afd-7add-821e72a35f03@suse.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
At least on the i350 there is an annoying behavior that is maybe also
present on 82580 devices, but was probably not noticed yet as MAS is not
widely used.
If no cable is connected on both fiber/copper ports the media auto sense
code will constantly swap between them as part of the watchdog task and
produce many unnecessary kernel log messages.
The swap code responsible for this behavior (switching to fiber) should
not be executed if the current media type is copper and there is no signal
detected on the fiber port. In this case we can safely wait until the
AUTOSENSE_EN bit is cleared.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If rndis_filter_open() fails, we need to remove the rndis device created
in earlier steps, before returning an error code. Otherwise, the retry of
netvsc_attach() from its callers will fail and hang.
Fixes: 7b2ee50c0cd5 ("hv_netvsc: common detach logic") Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When rmmod hip04_eth.ko, we can get the following warning:
Task track: rmmod(1623)>bash(1591)>login(1581)>init(1)
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1623 at kernel/irq/manage.c:1557 __free_irq+0xa4/0x2ac()
Trying to free already-free IRQ 200
Modules linked in: ping(O) pramdisk(O) cpuinfo(O) rtos_snapshot(O) interrupt_ctrl(O) mtdblock mtd_blkdevrtfs nfs_acl nfs lockd grace sunrpc xt_tcpudp ipt_REJECT iptable_filter ip_tables x_tables nf_reject_ipv
CPU: 0 PID: 1623 Comm: rmmod Tainted: G O 4.4.193 #1
Hardware name: Hisilicon A15
[<c020b408>] (rtos_unwind_backtrace) from [<c0206624>] (show_stack+0x10/0x14)
[<c0206624>] (show_stack) from [<c03f2be4>] (dump_stack+0xa0/0xd8)
[<c03f2be4>] (dump_stack) from [<c021a780>] (warn_slowpath_common+0x84/0xb0)
[<c021a780>] (warn_slowpath_common) from [<c021a7e8>] (warn_slowpath_fmt+0x3c/0x68)
[<c021a7e8>] (warn_slowpath_fmt) from [<c026876c>] (__free_irq+0xa4/0x2ac)
[<c026876c>] (__free_irq) from [<c0268a14>] (free_irq+0x60/0x7c)
[<c0268a14>] (free_irq) from [<c0469e80>] (release_nodes+0x1c4/0x1ec)
[<c0469e80>] (release_nodes) from [<c0466924>] (__device_release_driver+0xa8/0x104)
[<c0466924>] (__device_release_driver) from [<c0466a80>] (driver_detach+0xd0/0xf8)
[<c0466a80>] (driver_detach) from [<c0465e18>] (bus_remove_driver+0x64/0x8c)
[<c0465e18>] (bus_remove_driver) from [<c02935b0>] (SyS_delete_module+0x198/0x1e0)
[<c02935b0>] (SyS_delete_module) from [<c0202ed0>] (__sys_trace_return+0x0/0x10)
---[ end trace bb25d6123d849b44 ]---
Currently "rmmod hip04_eth.ko" call free_irq more than once
as devres_release_all and hip04_remove both call free_irq.
This results in a 'Trying to free already-free IRQ' warning.
To solve the problem free_irq has been moved out of hip04_remove.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In the highly unlikely event that we fail to allocate either of the
"/txrx" or "/control" workqueues, we should bail cleanly rather than
blindly march on with NULL queue pointer(s) installed in the
'fjes_adapter' instance.
Cc: "David S. Miller" <davem@davemloft.net> Reported-by: Nicolas Waisman <nico@semmle.com> Link: https://lore.kernel.org/lkml/CADJ_3a8WFrs5NouXNqS5WYe7rebFP+_A5CheeqAyD_p7DFJJcg@mail.gmail.com/ Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Endpoints with a maxpacket length of 0 are probably useless. They
can't transfer any data, and it's not at all unlikely that an HCD will
crash or hang when trying to handle an URB for such an endpoint.
Currently the USB core does not check for endpoints having a maxpacket
value of 0. This patch adds a check, printing a warning and skipping
over any endpoints it catches.
Now, the USB spec does not rule out endpoints having maxpacket = 0.
But since they wouldn't have any practical use, there doesn't seem to
be any good reason for us to accept them.
This saves us writing the IBS control MSR twice when disabling the
event.
I searched revision guides for all families since 10h, and did not
find occurrence of erratum #420, nor anything remotely similar:
so we isolate the secondary MSR write to family 10h only.
Also unconditionally update the count mask for IBS Op implementations
that have read & writeable current count (CurCnt) fields in addition
to the MaxCnt field. These bits were reserved on prior
implementations, and therefore shouldn't have negative impact.
Signed-off-by: Kim Phillips <kim.phillips@amd.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Fixes: c9574fe0bdb9 ("perf/x86-ibs: Implement workaround for IBS erratum #420") Link: https://lkml.kernel.org/r/20191023150955.30292-2-kim.phillips@amd.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The loop that reads all the IBS MSRs into *buf stopped one MSR short of
reading the IbsOpData register, which contains the RipInvalid status bit.
Fix the offset_max assignment so the MSR gets read, so the RIP invalid
evaluation is based on what the IBS h/w output, instead of what was
left in memory.
Signed-off-by: Kim Phillips <kim.phillips@amd.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Fixes: d47e8238cd76 ("perf/x86-ibs: Take instruction pointer from ibs sample") Link: https://lkml.kernel.org/r/20191023150955.30292-1-kim.phillips@amd.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
layerscape board sometimes reported some usb call trace, that is due to
kernel sent LPM tokerns automatically when it has no pending transfers
and think that the link is idle enough to enter L1, which procedure will
ask usb register has a recovery,then kernel will compare USBx_GFLADJ and
set GFLADJ_30MHZ, GFLADJ_30MHZ_REG until GFLADJ_30MHZ is equal 0x20, if
the conditions were met then issue occur, but whatever the conditions
whether were met that usb is all need keep GFLADJ_30MHZ of value is 0x20
(xhci spec ask use GFLADJ_30MHZ to adjust any offset from clock source
that generates the clock that drives the SOF counter, 0x20 is default
value of it)That is normal logic, so need remove the call trace.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We meet several NULL pointer issues if configfs_composite_unbind
and composite_setup (or composite_disconnect) are running together.
These issues occur when do the function switch stress test, the
configfs_compsoite_unbind is called from user mode by
echo "" to /sys/../UDC entry, and meanwhile, the setup interrupt
or disconnect interrupt occurs by hardware. The composite_setup
will get the cdev from get_gadget_data, but configfs_composite_unbind
will set gadget data as NULL, so the NULL pointer issue occurs.
This concurrent is hard to reproduce by native kernel, but can be
reproduced by android kernel.
In this commit, we introduce one spinlock belongs to structure
gadget_info since we can't use the same spinlock in usb_composite_dev
due to exclusive running together between composite_setup and
configfs_composite_unbind. And one bit flag 'unbind' to indicate the
code is at unbind routine, this bit is needed due to we release the
lock at during configfs_composite_unbind sometimes, and composite_setup
may be run at that time.
composite_dev_cleanup call from the failure of configfs_composite_bind
frees up the cdev->os_desc_req and cdev->req. If the previous calls of
bind and unbind is successful these will carry stale values.
Consider the below sequence of function calls:
configfs_composite_bind()
composite_dev_prepare()
- Allocate cdev->req, cdev->req->buf
composite_os_desc_req_prepare()
- Allocate cdev->os_desc_req, cdev->os_desc_req->buf
configfs_composite_unbind()
composite_dev_cleanup()
- free the cdev->os_desc_req->buf and cdev->req->buf
Next composition switch
configfs_composite_bind()
- If it fails goto err_comp_cleanup will call the
composite_dev_cleanup() function
composite_dev_cleanup()
- calls kfree up with the stale values of cdev->req->buf and
cdev->os_desc_req from the previous configfs_composite_bind
call. The free call on these stale values leads to double free.
Hence, Fix this issue by setting request and buffer pointer to NULL after
kfree.
Fix interrupt storm generated by endpoints when working in FIFO mode.
The TX_COMPLETE interrupt is used only by control endpoints processing.
Do not enable it for other types of endpoints.
When a macsec interface is created, it increases a refcnt to a lower
device(real device). when macsec interface is deleted, the refcnt is
decreased in macsec_free_netdev(), which is ->priv_destructor() of
macsec interface.
The problem scenario is this.
When nested macsec interfaces are exiting, the exit routine of the
macsec module makes refcnt leaks.
Test commands:
ip link add dummy0 type dummy
ip link add macsec0 link dummy0 type macsec
ip link add macsec1 link macsec0 type macsec
modprobe -rv macsec
[ 208.629433] unregister_netdevice: waiting for macsec0 to become free. Usage count = 1
Steps of exit routine of macsec module are below.
1. Calls ->dellink() in __rtnl_link_unregister().
2. Checks refcnt and wait refcnt to be 0 if refcnt is not 0 in
netdev_run_todo().
3. Calls ->priv_destruvtor() in netdev_run_todo().
Step2 checks refcnt, but step3 decreases refcnt.
So, step2 waits forever.
This patch makes the macsec module do not hold a refcnt of the lower
device because it already holds a refcnt of the lower device with
netdev_upper_dev_link().
Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The IFF_BONDING means bonding master or bonding slave device.
->ndo_add_slave() sets IFF_BONDING flag and ->ndo_del_slave() unsets
IFF_BONDING flag.
bond0<--bond1
Both bond0 and bond1 are bonding device and these should keep having
IFF_BONDING flag until they are removed.
But bond1 would lose IFF_BONDING at ->ndo_del_slave() because that routine
do not check whether the slave device is the bonding type or not.
This patch adds the interface type check routine before removing
IFF_BONDING flag.
Test commands:
ip link add bond0 type bond
ip link add bond1 type bond
ip link set bond1 master bond0
ip link set bond1 nomaster
ip link del bond1 type bond
ip link add bond1 type bond
BUG: KCSAN: data-race in update_defense_level / update_defense_level
read to 0xffffffff861a6260 of 4 bytes by task 3006 on cpu 1:
update_defense_level+0x621/0xb30 net/netfilter/ipvs/ip_vs_ctl.c:177
defense_work_handler+0x3d/0xd0 net/netfilter/ipvs/ip_vs_ctl.c:225
process_one_work+0x3d4/0x890 kernel/workqueue.c:2269
worker_thread+0xa0/0x800 kernel/workqueue.c:2415
kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352
write to 0xffffffff861a6260 of 4 bytes by task 7333 on cpu 0:
update_defense_level+0xa62/0xb30 net/netfilter/ipvs/ip_vs_ctl.c:205
defense_work_handler+0x3d/0xd0 net/netfilter/ipvs/ip_vs_ctl.c:225
process_one_work+0x3d4/0x890 kernel/workqueue.c:2269
worker_thread+0xa0/0x800 kernel/workqueue.c:2415
kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 7333 Comm: kworker/0:5 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: events defense_work_handler
Indeed, old_secure_tcp is currently a static variable, while it
needs to be a per netns variable.
Fixes: a0840e2e165a ("IPVS: netns, ip_vs_ctl local vars moved to ipvs struct.") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
if the IPVS module is removed while the sync daemon is starting, there is
a small gap where try_module_get() might fail getting the refcount inside
ip_vs_use_count_inc(). Then, the refcounts of IPVS module are unbalanced,
and the subsequent call to stop_sync_thread() causes the following splat:
Check the return value of ip_vs_use_count_inc() and let its caller return
proper error. Inside do_ip_vs_set_ctl() the module is already refcounted,
we don't need refcount/derefcount there. Finally, in register_ip_vs_app()
and start_sync_thread(), take the module refcount earlier and ensure it's
released in the error path.
Change since v1:
- better return values in case of failure of ip_vs_use_count_inc(),
thanks to Julian Anastasov
- no need to increase/decrease the module refcount in ip_vs_set_ctl(),
thanks to Julian Anastasov
This patch fixes issue with Gen7 adapter in a blade environment where one
of the ports will not be detected by driver. Firmware expects mailbox 11 to
be set or cleared by driver for newer ISP.
A customer reports that after a devloss, an ADISC failure is logged. It
turns out the ADISC flag is set even the user explicitly set lpfc_use_adisc
= 0.
[Sat Dec 22 22:55:58 2018] lpfc 0000:82:00.0: 2:(0):0203 Devloss timeout on WWPN 50:01:43:80:12:8e:40:20 NPort x05df00 Data: x82000000 x8 xa
[Sat Dec 22 23:08:20 2018] lpfc 0000:82:00.0: 2:(0):2755 ADISC failure DID:05DF00 Status:x9/x70000
[mkp: fixed Hannes' email]
Fixes: 92d7f7b0cde3 ("[SCSI] lpfc: NPIV: add NPIV support on top of SLI-3") Cc: Dick Kennedy <dick.kennedy@broadcom.com> Cc: James Smart <james.smart@broadcom.com> Link: https://lore.kernel.org/r/20191022072112.132268-1-dwagner@suse.de Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: James Smart <james.smart@broadcom.com> Signed-off-by: Daniel Wagner <dwagner@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The function in net core, register_netdevice(), may fail with vport's
destruction callback either invoked or not. After commit 309b66970ee2
("net: openvswitch: do not free vport if register_netdevice() is failed."),
the duty to destroy vport is offloaded from the driver OTOH, which ends
up in the memory leak reported.
It is fixed by releasing vport unless device is registered successfully.
To do that, the callback assignment is defered until device is registered.
Reported-by: syzbot+13210896153522fe1ee5@syzkaller.appspotmail.com Fixes: 309b66970ee2 ("net: openvswitch: do not free vport if register_netdevice() is failed.") Cc: Taehee Yoo <ap420073@gmail.com> Cc: Greg Rose <gvrose8192@gmail.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Cc: Ying Xue <ying.xue@windriver.com> Cc: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Hillf Danton <hdanton@sina.com> Acked-by: Pravin B Shelar <pshelar@ovn.org>
[sbrivio: this was sent to dev@openvswitch.org and never made its way
to netdev -- resending original patch] Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Reviewed-by: Greg Rose <gvrose8192@gmail.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The issue is in drivers/infiniband/core/uverbs_std_types_cq.c in the
UVERBS_HANDLER(UVERBS_METHOD_CQ_CREATE) function. We check that:
if (attr.comp_vector >= attrs->ufile->device->num_comp_vectors) {
But we don't check if "attr.comp_vector" is negative. It could
potentially lead to an array underflow. My concern would be where
cq->vector is used in the create_cq() function from the cxgb4 driver.
And really "attr.comp_vector" is appears as a u32 to user space so that's
the right type to use.
Fixes: 9ee79fce3642 ("IB/core: Add completion queue (cq) object actions") Link: https://lore.kernel.org/r/20191011133419.GA22905@mwanda Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In vdma_channel_set_config clear the delay, frame count and master mask
before updating their new values. It avoids programming incorrect state
when input parameters are different from default.
The PCI Tegra controller conversion to a device tree configurable
driver in commit d1523b52bff3 ("PCI: tegra: Move PCIe driver
to drivers/pci/host") implied that code for the driver can be
compiled in for a kernel supporting multiple platforms.
Unfortunately, a blind move of the code did not check that some of the
quirks that were applied in arch/arm (eg enabling Relaxed Ordering on
all PCI devices - since the quirk hook erroneously matches PCI_ANY_ID
for both Vendor-ID and Device-ID) are now applied in all kernels that
compile the PCI Tegra controlled driver, DT and ACPI alike.
This is completely wrong, in that enablement of Relaxed Ordering is only
required by default in Tegra20 platforms as described in the Tegra20
Technical Reference Manual (available at
https://developer.nvidia.com/embedded/downloads#?search=tegra%202 in
Section 34.1, where it is mentioned that Relaxed Ordering bit needs to
be enabled in its root ports to avoid deadlock in hardware) and in the
Tegra30 platforms for the same reasons (unfortunately not documented
in the TRM).
There is no other strict requirement on PCI devices Relaxed Ordering
enablement on any other Tegra platforms or PCI host bridge driver.
Fix this quite upsetting situation by limiting the vendor and device IDs
to which the Relaxed Ordering quirk applies to the root ports in
question, reported above.
There are bugs on vhci with usb 3.0 storage device. In USB, each SG
list entry buffer should be divisible by the bulk max packet size.
But with native SG support, this problem doesn't matter because the
SG buffer is treated as contiguous buffer. But without native SG
support, USB storage driver breaks SG list into several URBs and the
error occurs because of a buffer size of URB that cannot be divided
by the bulk max packet size. The error situation is as follows.
When USB Storage driver requests 31.5 KB data and has SG list which
has 3584 bytes buffer followed by 7 4096 bytes buffer for some
reason. USB Storage driver splits this SG list into several URBs
because VHCI doesn't support SG and sends them separately. So the
first URB buffer size is 3584 bytes. When receiving data from device,
USB 3.0 device sends data packet of 1024 bytes size because the max
packet size of BULK pipe is 1024 bytes. So device sends 4096 bytes.
But the first URB buffer has only 3584 bytes buffer size. So host
controller terminates the transfer even though there is more data to
receive. So, vhci needs to support SG transfer to prevent this error.
In this patch, vhci supports SG regardless of whether the server's
host controller supports SG or not, because stub driver splits SG
list into several URBs if the server's host controller doesn't
support SG.
To support SG, vhci sets URB_DMA_MAP_SG flag in urb->transfer_flags
if URB has SG list and this flag will tell stub driver to use SG
list. After receiving urb from stub driver, vhci clear URB_DMA_MAP_SG
flag to avoid unnecessary DMA unmapping in HCD.
vhci sends each SG list entry to stub driver. Then, stub driver sees
the total length of the buffer and allocates SG table and pages
according to the total buffer length calling sgl_alloc(). After stub
driver receives completed URB, it again sends each SG list entry to
vhci.
If the server's host controller doesn't support SG, stub driver
breaks a single SG request into several URBs and submits them to
the server's host controller. When all the split URBs are completed,
stub driver reassembles the URBs into a single return command and
sends it to vhci.
Moreover, in the situation where vhci supports SG, but stub driver
does not, or vice versa, usbip works normally. Because there is no
protocol modification, there is no problem in communication between
server and client even if the one has a kernel without SG support.
In the case of vhci supports SG and stub driver doesn't, because
vhci sends only the total length of the buffer to stub driver as
it did before the patch applied, stub driver only needs to allocate
the required length of buffers using only kmalloc() regardless of
whether vhci supports SG or not. But stub driver has to allocate
buffer with kmalloc() as much as the total length of SG buffer which
is quite huge when vhci sends SG request, so it has overhead in
buffer allocation in this situation.
If stub driver needs to send data buffer to vhci because of IN pipe,
stub driver also sends only total length of buffer as metadata and
then sends real data as vhci does. Then vhci receive data from stub
driver and store it to the corresponding buffer of SG list entry.
And for the case of stub driver supports SG and vhci doesn't, since
the USB storage driver checks that vhci doesn't support SG and sends
the request to stub driver by splitting the SG list into multiple
URBs, stub driver allocates a buffer for each URB with kmalloc() as
it did before this patch.
* Test environment
Test uses two difference machines and two different kernel version
to make mismatch situation between the client and the server where
vhci supports SG, but stub driver does not, or vice versa. All tests
are conducted in both full SG support that both vhci and stub support
SG and half SG support that is the mismatch situation. Test kernel
version is 5.3-rc6 with commit "usb: add a HCD_DMA flag instead of
guestimating DMA capabilities" to avoid unnecessary DMA mapping and
unmapping.
- Test kernel version
- 5.3-rc6 with SG support
- 5.1.20-200.fc29.x86_64 without SG support
* SG support test
- Test devices
- Super-speed storage device - SanDisk Ultra USB 3.0
- High-speed storage device - SMI corporation USB 2.0 flash drive
- Test description
Test read and write operation of mass storage device that uses the
BULK transfer. In test, the client reads and writes files whose size
is over 1G and it works normally.
* Regression test
- Test devices
- Super-speed device - Logitech Brio webcam
- High-speed device - Logitech C920 HD Pro webcam
- Full-speed device - Logitech bluetooth mouse
- Britz BR-Orion speaker
- Low-speed device - Logitech wired mouse
- Test description
Moving and click test for mouse. To test the webcam, use gnome-cheese.
To test the speaker, play music and video on the client. All works
normally.
* VUDC compatibility test
VUDC also works well with this patch. Tests are done with two USB
gadget created by CONFIGFS USB gadget. Both use the BULK pipe.
1. Serial gadget
2. Mass storage gadget
- Serial gadget test
Serial gadget on the host sends and receives data using cat command
on the /dev/ttyGS<N>. The client uses minicom to communicate with
the serial gadget.
- Mass storage gadget test
After connecting the gadget with vhci, use "dd" to test read and
write operation on the client side.