AER info of PCIe fatal error is not printed in the current driver.
Because APEI driver will panic directly for fatal error, and can't
run to the place of printing AER info.
An example log is as following:
{763}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 11
{763}[Hardware Error]: event severity: fatal
{763}[Hardware Error]: Error 0, type: fatal
{763}[Hardware Error]: section_type: PCIe error
{763}[Hardware Error]: port_type: 0, PCIe end point
{763}[Hardware Error]: version: 4.0
{763}[Hardware Error]: command: 0x0000, status: 0x0010
{763}[Hardware Error]: device_id: 0000:82:00.0
{763}[Hardware Error]: slot: 0
{763}[Hardware Error]: secondary_bus: 0x00
{763}[Hardware Error]: vendor_id: 0x8086, device_id: 0x10fb
{763}[Hardware Error]: class_code: 000002
Kernel panic - not syncing: Fatal hardware error!
This issue was imported by the patch, '37448adfc7ce ("aerdrv: Move
cper_print_aer() call out of interrupt context")'. To fix this issue,
this patch adds print of AER info in cper_print_pcie() for fatal error.
Here is the example log after this patch applied:
{24}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 10
{24}[Hardware Error]: event severity: fatal
{24}[Hardware Error]: Error 0, type: fatal
{24}[Hardware Error]: section_type: PCIe error
{24}[Hardware Error]: port_type: 0, PCIe end point
{24}[Hardware Error]: version: 4.0
{24}[Hardware Error]: command: 0x0546, status: 0x4010
{24}[Hardware Error]: device_id: 0000:01:00.0
{24}[Hardware Error]: slot: 0
{24}[Hardware Error]: secondary_bus: 0x00
{24}[Hardware Error]: vendor_id: 0x15b3, device_id: 0x1019
{24}[Hardware Error]: class_code: 000002
{24}[Hardware Error]: aer_uncor_status: 0x00040000, aer_uncor_mask: 0x00000000
{24}[Hardware Error]: aer_uncor_severity: 0x00062010
{24}[Hardware Error]: TLP Header: 000000c0010100000000000100000000
Kernel panic - not syncing: Fatal hardware error!
Fixes: 37448adfc7ce ("aerdrv: Move cper_print_aer() call out of interrupt context") Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com> Reviewed-by: James Morse <james.morse@arm.com>
[ardb: put parens around terms of && operator] Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Depending on how BIOS has marked the reserved region containing the 32KB
MCHBAR you can get warnings like:
resource sanity check: requesting [mem 0xfed10000-0xfed1ffff], which spans more than reserved [mem 0xfed10000-0xfed17fff]
caller dnv_rd_reg+0xc8/0x240 [pnd2_edac] mapping multiple BARs
Not all of the mmio regions used in dnv_rd_reg() are the same size. The
MCHBAR window is 32KB and the sideband ports are 64KB. Pass the correct
size to ioremap() depending on which resource we're reading from.
Signed-off-by: Stephen Douthit <stephend@silicom-usa.com> Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The processors marked as 0xff are invalid, there are only 8 of them in
this case.
So do not print an error on ids == 0xff, just print an info message.
Actually, we could return ENODEV even on the first CPU with ID 0xff, but
ACPI spec does not forbid the 0xff value to be a processor ID. Given
0xff could be a correct one, we would break working systems if we
returned ENODEV.
Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Then from kernel side, Manage_add invokes the path (add_new_disk ->
validate_super = super_1_validate) to set In_sync flag.
Since In_sync means "device is in_sync with rest of array", and the new
added disk need to resync thread to help the synchronization of data.
And md_reap_sync_thread would call spare_active to set In_sync for the
new added disk finally. So don't set In_sync if array is in frozen.
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When add one disk to array, the md_reap_sync_thread is responsible
to activate the spare and set In_sync flag for the new member in
spare_active().
But if raid1 has one member disk A, and disk B is added to the array.
Then we offline A before all the datas are synchronized from A to B,
obviously B doesn't have the latest data as A, but B is still marked
with In_sync flag.
So let's not call spare_active under the condition, otherwise B is
still showed with 'U' state which is not correct.
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When write bio return error, it would be added to conf->retry_list
and wait for raid1d thread to retry write and acknowledge badblocks.
In narrow_write_error(), the error bio will be split in the unit of
badblock shift (such as one sector) and raid1d thread issues them
one by one. Until all of the splited bio has finished, raid1d thread
can go on processing other things, which is time consuming.
But, there is a scene for error handling that is not necessary.
When the device has been set faulty, flush_bio_list() may end
bios in pending_bio_list with error status. Since these bios
has not been issued to the device actually, error handlding to
retry write and acknowledge badblocks make no sense.
Even without that scene, when the device is faulty, badblocks info
can not be written out to the device. Thus, we also no need to
handle the error IO.
Signed-off-by: Yufen Yu <yuyufen@huawei.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
ADG is using clk_get_rate() under atomic context, thus, we might
have scheduling issue.
To avoid this issue, we need to get/keep clk rate under
non atomic context.
We need to handle ADG as special device at Renesas Sound driver.
From SW point of view, we want to impletent it as
rsnd_mod_ops :: prepare, but it makes code just complicate.
To avoid complicated code/patch, this patch adds new clk_rate[] array,
and keep clk IN rate when rsnd_adg_clk_enable() was called.
Reported-by: Leon Kong <Leon.KONG@cn.bosch.com> Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Tested-by: Leon Kong <Leon.KONG@cn.bosch.com> Link: https://lore.kernel.org/r/87v9vb0xkp.wl-kuninori.morimoto.gx@renesas.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The Linux kernel assumes that get_endpoint(alts,0) and
get_endpoint(alts,1) are eachothers feedback endpoints.
To reassure that validity it will test bsynchaddress to comply with that
assumption. But if the bsyncaddress is 0 (invalid), it will flag that as
a wrong assumption and return an error.
Fix: Skip the test if bSynchAddress is 0.
Note: those with a valid bSynchAddress should have a code quirck added.
Signed-off-by: Ard van Breemen <ard@kwaak.net> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In build_adc_controls(), there is an if statement on line 773 to check
whether ak->adc_info is NULL:
if (! ak->adc_info ||
! ak->adc_info[mixer_ch].switch_name)
When ak->adc_info is NULL, it is used on line 792:
knew.name = ak->adc_info[mixer_ch].selector_name;
Thus, a possible null-pointer dereference may occur.
To fix this bug, referring to lines 773 and 774, ak->adc_info
and ak->adc_info[mixer_ch].selector_name are checked before being used.
This bug is found by a static analysis tool STCheck written by us.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The last fallback of CORB/RIRB communication error recovery is to turn
on the single command mode, and this last resort usually means that
something is really screwed up. Instead of a normal dev_err(), show
the error more clearly with dev_WARN() with the caller stack trace.
Also, show the bus-reset fallback also as an error, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
A reboot request sends an IPI via the reboot vector and waits for all other
CPUs to stop. If one or more CPUs are in critical regions with interrupts
disabled then the IPI is not handled on those CPUs and the shutdown hangs
if native_stop_other_cpus() is called with the wait argument set.
Such a situation can happen when one CPU was stopped within a lock held
section and another CPU is trying to acquire that lock with interrupts
disabled. There are other scenarios which can cause such a lockup as well.
In theory the shutdown should be attempted by an NMI IPI after the timeout
period elapsed. Though the wait loop after sending the reboot vector IPI
prevents this. It checks the wait request argument and the timeout. If wait
is set, which is true for sys_reboot() then it won't fall through to the
NMI shutdown method after the timeout period has finished.
This was an oversight when the NMI shutdown mechanism was added to handle
the 'reboot IPI is not working' situation. The mechanism was added to deal
with stuck panic shutdowns, which do not have the wait request set, so the
'wait request' case was probably not considered.
Remove the wait check from the post reboot vector IPI wait loop and enforce
that the wait loop in the NMI fallback path is invoked even if NMI IPIs are
disabled or the registration of the NMI handler fails. That second wait
loop will then hang if not all CPUs shutdown and the wait argument is set.
[ tglx: Avoid the hard to parse line break in the NMI fallback path,
add comments and massage the changelog ]
Fixes: 7d007d21e539 ("x86/reboot: Use NMI to assist in shutting down if IRQ fails") Signed-off-by: Grzegorz Halat <ghalat@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Don Zickus <dzickus@redhat.com> Link: https://lkml.kernel.org/r/20190628122813.15500-1-ghalat@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
On !CONFIG_RT_GROUP_SCHED configurations it is currently not possible to
move RT tasks between cgroups to which CPU controller has been attached;
but it is oddly possible to first move tasks around and then make them
RT (setschedule to FIFO/RR).
Also, as Michal noted, it is currently not possible to enable CPU
controller on unified hierarchy with !CONFIG_RT_GROUP_SCHED (if there
are any kernel RT threads in root cgroup, they can't be migrated to the
newly created CPU controller's root in cgroup_update_dfl_csses()).
Existing code comes with a comment saying the "we don't support RT-tasks
being in separate groups". Such comment is however stale and belongs to
pre-RT_GROUP_SCHED times. Also, it doesn't make much sense for
!RT_GROUP_ SCHED configurations, since checks related to RT bandwidth
are not performed at all in these cases.
Make moving RT tasks between CPU controller groups viable by removing
special case check for RT (and DEADLINE) tasks.
Signed-off-by: Juri Lelli <juri.lelli@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Michal Koutný <mkoutny@suse.com> Reviewed-by: Daniel Bristot de Oliveira <bristot@redhat.com> Acked-by: Tejun Heo <tj@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: lizefan@huawei.com Cc: longman@redhat.com Cc: luca.abeni@santannapisa.it Cc: rostedt@goodmis.org Link: https://lkml.kernel.org/r/20190719063455.27328-1-juri.lelli@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The load_balance() has a dedicated mecanism to detect when an imbalance
is due to CPU affinity and must be handled at parent level. In this case,
the imbalance field of the parent's sched_group is set.
The description of sg_imbalanced() gives a typical example of two groups
of 4 CPUs each and 4 tasks each with a cpumask covering 1 CPU of the first
group and 3 CPUs of the second group. Something like:
{ 0 1 2 3 } { 4 5 6 7 }
* * * *
But the load_balance fails to fix this UC on my octo cores system
made of 2 clusters of quad cores.
Whereas the load_balance is able to detect that the imbalanced is due to
CPU affinity, it fails to fix it because the imbalance field is cleared
before letting parent level a chance to run. In fact, when the imbalance is
detected, the load_balance reruns without the CPU with pinned tasks. But
there is no other running tasks in the situation described above and
everything looks balanced this time so the imbalance field is immediately
cleared.
The imbalance field should not be cleared if there is no other task to move
when the imbalance is detected.
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/1561996022-28829-1-git-send-email-vincent.guittot@linaro.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The power down and reset GPIO are optional, but the return value
from devm_gpiod_get_optional() needs to be checked and propagated
in the case of error, so that probe deferral can work.
Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
We need to increment the device count atomically before we checkout a
device to make sure that we do not reach the max count, otherwise we get
out-of-bounds errors as reported by syzbot.
Reported-and-tested-by: syzbot+aac8d0d7205f112045d2@syzkaller.appspotmail.com Signed-off-by: Luke Nowakowski-Krijger <lnowakow@eng.ucsd.edu> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The call to of_get_child_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
drivers/media/platform/exynos4-is/fimc-is.c:813:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 807, but without a corresponding object release within this function.
drivers/media/platform/exynos4-is/fimc-is.c:870:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 807, but without a corresponding object release within this function.
drivers/media/platform/exynos4-is/fimc-is.c:885:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 807, but without a corresponding object release within this function.
drivers/media/platform/exynos4-is/media-dev.c:545:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 541, but without a corresponding object release within this function.
drivers/media/platform/exynos4-is/media-dev.c:528:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 499, but without a corresponding object release within this function.
drivers/media/platform/exynos4-is/media-dev.c:534:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 499, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The rc-mm protocol can't be decoded by the mtk-cir since the de-glitch
filter removes pulses/spaces shorter than 294 microseconds.
Tested on a BananaPi R2.
Signed-off-by: Sean Young <sean@mess.org> Acked-by: Sean Wang <sean.wang@kernel.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When CONFIG_DVB_DIB9000 is disabled, we can still compile code that
now fails to link against dibx000_i2c_set_speed:
drivers/media/usb/dvb-usb/dib0700_devices.o: In function `dib01x0_pmu_update.constprop.7':
dib0700_devices.c:(.text.unlikely+0x1c9c): undefined reference to `dibx000_i2c_set_speed'
The call sites are both through dib01x0_pmu_update(), which gets passed
an 'i2c' pointer from dib9000_get_i2c_master(), which has returned
NULL. Checking this pointer seems to be a good idea anyway, and it avoids
the link failure in most cases.
Sean Young found another case that is not fixed by that, where certain
gcc versions leave an unused function in place that causes the link error,
but adding an explict IS_ENABLED() check also solves this.
Fixes: b7f54910ce01 ("V4L/DVB (4647): Added module for DiB0700 based devices") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Firmware files are in ASCII, using 2 hex characters per byte. The
maximum length of a firmware string is therefore
16 (commands) * 2 (bytes per command) * 2 (characters per byte) = 64
Fixes: ff45262a85db ("leds: add new LP5562 LED driver") Signed-off-by: Nick Stoughton <nstoughton@logitech.com> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
According to the datasheet https://www.ti.com/lit/ds/symlink/lm3632a.pdf
Table 20. VPOS Bias Register Field Descriptions VPOS[5:0]
Sets the Positive Display Bias (LDO) Voltage (50 mV per step)
000000: 4 V
000001: 4.05 V
000010: 4.1 V
....................
011101: 5.45 V
011110: 5.5 V (Default)
011111: 5.55 V
....................
100111: 5.95 V
101000: 6 V
Note: Codes 101001 to 111111 map to 6 V
The LM3632_LDO_VSEL_MAX should be 0b101000 (0x28), so the maximum voltage
can match the datasheet.
Fixes: 3a8d1a73a037 ("regulator: add LM363X driver") Signed-off-by: Axel Lin <axel.lin@ingics.com> Link: https://lore.kernel.org/r/20190626132632.32629-1-axel.lin@ingics.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
which has the hallmarks of a worker queued from interrupt after it was
supposedly cancelled (note the POISON_FREE), and I could not see where
the interrupt would be flushed on shutdown so added the likely suspects.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111174 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When creating a raw AF_NFC socket, CAP_NET_RAW needs to be checked
first.
Signed-off-by: Ori Nimron <orinimron123@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When creating a raw AF_IEEE802154 socket, CAP_NET_RAW needs to be
checked first.
Signed-off-by: Ori Nimron <orinimron123@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When creating a raw AF_AX25 socket, CAP_NET_RAW needs to be checked
first.
Signed-off-by: Ori Nimron <orinimron123@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When creating a raw AF_APPLETALK socket, CAP_NET_RAW needs to be checked
first.
Signed-off-by: Ori Nimron <orinimron123@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When creating a raw AF_ISDN socket, CAP_NET_RAW needs to be checked
first.
Signed-off-by: Ori Nimron <orinimron123@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Add the device ID of upcoming BlueField-2 integrated ConnectX-6 Dx
network controller. Its VFs will be using the generic VF device ID:
0x101e "ConnectX Family mlx5Gen Virtual Function".
Fixes: 2e9d3e83ab82 ("net/mlx5: Update the list of the PCI supported devices") Signed-off-by: Bodong Wang <bodong@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
After a reset packet sizes and device mtu can change and need
to be reevaluated to calculate queue sizes.
Malicious devices can set this to zero and we divide by it.
Introduce sanity checking.
Reported-and-tested-by: syzbot+6102c120be558c885f04@syzkaller.appspotmail.com Signed-off-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Endpoints with zero wMaxPacketSize are not usable for transferring
data. Ignore such endpoints when looking for valid in, out and
status pipes, to make the drivers more robust against invalid and
meaningless descriptors.
The wMaxPacketSize of these endpoints are used for memory allocations
and as divisors in many usbnet minidrivers. Avoiding zero is therefore
critical.
Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Running old skge driver on PowerPC causes checksum errors
because hardware reported 1's complement checksum is in little-endian
byte order.
Reported-by: Benoit <benoit.sansoni@gmail.com> Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
userspace openvswitch patch "(dpif-linux: Implement the API
functions to allow multiple handler threads read upcall)"
changes its type from U32 to UNSPEC, but leave the kernel
unchanged
and after kernel 6e237d099fac "(netlink: Relax attr validation
for fixed length types)", this bug is exposed by the below
warning
[ 57.215841] netlink: 'ovs-vswitchd': attribute type 5 has an invalid length.
Fixes: 5cd667b0a456 ("openvswitch: Allow each vport to have an array of 'port_id's") Signed-off-by: Li RongQing <lirongqing@baidu.com> Acked-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The TCA_KIND attribute is of NLA_STRING which does not check
the NUL char. KMSAN reported an uninit-value of TCA_KIND which
is likely caused by the lack of NUL.
Change it to NLA_NUL_STRING and add a max len too.
Fixes: 8b4c3cdd9dd8 ("net: sched: Add policy validation for tc attributes") Reported-and-tested-by: syzbot+618aacd49e8c8b8486bd@syzkaller.appspotmail.com Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
current 'sample' action doesn't push the mac header of ingress packets if
they are received by a layer 3 tunnel (like gre or sit); but it forgot to
check for gre over ipv6, so the following script:
# tc q a dev $d clsact
# tc f a dev $d ingress protocol ip flower ip_proto icmp action sample \
> group 100 rate 1
# psample -v -g 100
dumps everything, including outer header and mac, when $d is a gre tunnel
over ipv6. Fix this adding a missing label for ARPHRD_IP6GRE devices.
As the endpoint is unregistered there might still be work pending to
handle incoming messages, which will result in a use after free
scenario. The plan is to remove the rx_worker, but until then (and for
stable@) ensure that the work is stopped before the node is freed.
According to the DP83865 datasheet "the 10 Mbps HDX loopback can be
disabled in the expanded memory register 0x1C0.1". The driver erroneously
used bit 0 instead of bit 1.
Fixes: 4621bf129856 ("phy: Add file missed in previous commit.") Signed-off-by: Peter Mamonov <pmamonov@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The issue was caused by skb's true_size changed without its sk's
sk_wmem_alloc increased in tcp/skb_gro_receive(). Later when the
skb is being freed and the skb's truesize is subtracted from its
sk's sk_wmem_alloc in tcp_wfree(), underflow occurs.
macsec is calling gro_cells_receive() to receive a packet, which
actually requires skb->sk to be NULL. However when macsec dev is
over veth, it's possible the skb->sk is still set if the skb was
not unshared or expanded from the peer veth.
ip_rcv() is calling skb_orphan() to drop the skb's sk for tproxy,
but it is too late for macsec's calling gro_cells_receive(). So
fix it by dropping the skb's sk earlier on rx path of macsec.
Fixes: 5491e7c6b1a9 ("macsec: enable GRO and RPS on macsec devices") Reported-by: Xiumei Mu <xmu@redhat.com> Reported-by: Fei Liu <feliu@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Endpoints with zero wMaxPacketSize are not usable for transferring
data. Ignore such endpoints when looking for valid in, out and
status pipes, to make the driver more robust against invalid and
meaningless descriptors.
The wMaxPacketSize of the out pipe is used as divisor. So this change
fixes a divide-by-zero bug.
Reported-by: syzbot+ce366e2b8296e25d84f5@syzkaller.appspotmail.com Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
struct archdr is only big enough to hold the header of various types of
arcnet packets. So to provide enough space to hold the data read from
hardware provide a buffer large enough to hold a packet with maximal
size.
The problem was noticed by the stack protector which makes the kernel
oops.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
f2fs uses EFAULT as error number to indicate filesystem is corrupted
all the time, but generic filesystems use EUCLEAN for such condition,
we need to change to follow others.
This patch adds two new macros as below to wrap more generic error
code macros, and spread them in code.
EFSBADCRC EBADMSG /* Bad CRC detected */
EFSCORRUPTED EUCLEAN /* Filesystem is corrupted */
Reported-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Chao Yu <yuchao0@huawei.com> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The "obvious" cause is that the attr ifork is null despite the inode
claiming an attr fork having at least one extent, but it's not so
obvious why we ended up with an inode in that state.
Reported-by: Zorro Lang <zlang@redhat.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204031 Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Bill O'Donnell <billodo@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Some machines change the brightness themselves when a brightness hotkey
gets pressed, despite us telling them not to. This causes the brightness to
go two steps up / down when the hotkey is pressed. This is esp. a problem
on older machines with only a few brightness levels.
This commit adds a new hw_changes_brightness quirk which makes
acpi_video_device_notify() only call backlight_force_update(...,
BACKLIGHT_UPDATE_HOTKEY) and not do anything else, notifying userspace
that the brightness was changed and leaving it at that fixing the dual
step problem.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=204077 Reported-by: Kacper Piwiński <cosiekvfj@o2.pl> Tested-by: Kacper Piwiński <cosiekvfj@o2.pl> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If IPV6 was disabled, then ss command would cause a kernel warning
because the command was attempting to dump IPV6 socket information.
The fix is to just remove the warning.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202249 Fixes: 432490f9d455 ("net: ip, diag -- Add diag interface for raw sockets") Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
We need to mark the output polling as disabled to prevent concurrent
irqs from queuing new work as shutdown the probe -- causing that work to
execute after we have freed the structs:
The testcase fails because that, in fuzzed image, current segment was
allocated with LFS type, its .next_blkoff should point to an unused
block address, but actually, its bitmap shows it's not. So during
allocation, f2fs crash when setting bitmap.
Introducing sanity_check_curseg() to check such inconsistence of
current in-used segment.
Signed-off-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
"We normally use -EUCLEAN to signal filesystem corruption. Plus, it is
good idea to report it to the syslog and mark filesystem as "needing
fsck" if filesystem can do that."
Still we need improve the original patch with:
- use unlikely keyword
- add message print
- return EUCLEAN
However, after rethink this patch, I don't think we should add such
condition check here as below reasons:
- We have already checked the field in f2fs_sanity_check_ckpt(),
- If there is fs corrupt or security vulnerability, there is nothing
to guarantee the field is integrated after the check, unless we do
the check before each of its use, however no filesystem does that.
- We only have similar check for bitmap, which was added due to there
is bitmap corruption happened on f2fs' runtime in product.
- There are so many key fields in SB/CP/NAT did have such check
after f2fs_sanity_check_{sb,cp,..}.
blk_exit_queue will free elevator_data, while blk_mq_requeue_work
will access it. Move cancel of requeue_work to the front of
blk_exit_queue to avoid use-after-free.
The slot must be removed before the pci_dev is removed, otherwise a panic
can happen due to use-after-free.
Fixes: 15becc2b56c6 ("PCI: hv: Add hv_pci_remove_slots() when we unload the driver") Signed-off-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
As a part of the sanity checking while mounting, distinct segment number
assignment to data and node segments is verified. Fixing a small bug in
this verification between node and data segments. We need to check all
the data segments with all the node segments.
Fixes: 042be0f849e5f ("f2fs: fix to do sanity check with current segment number") Signed-off-by: Surbhi Palande <csurbhi@gmail.com> Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When allocating a range of LPIs for a Multi-MSI capable device,
this allocation extended to the closest power of 2.
But on the release path, the interrupts are released one by
one. This results in not releasing the "extra" range, leaking
the its_device. Trying to reprobe the device will then fail.
Fix it by releasing the LPIs the same way we allocate them.
Fixes: 8208d1708b88 ("irqchip/gic-v3-its: Align PCI Multi-MSI allocation on their size") Reported-by: Jiaxing Luo <luojiaxing@huawei.com> Tested-by: John Garry <john.garry@huawei.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/f5e948aa-e32f-3f74-ae30-31fee06c2a74@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This adds rate limiting to the message that is printed when reading a
power supply property via sysfs returns an error. This will prevent
userspace applications from unintentionally dDOSing the system by
continuously reading a property that returns an error.
Signed-off-by: David Lechner <david@lechnology.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Clang warns when one enumerated type is implicitly converted to another:
drivers/pinctrl/sprd/pinctrl-sprd.c:845:19: warning: implicit conversion
from enumeration type 'enum sprd_pinconf_params' to different
enumeration type 'enum pin_config_param' [-Wenum-conversion]
{"sprd,control", SPRD_PIN_CONFIG_CONTROL, 0},
~ ^~~~~~~~~~~~~~~~~~~~~~~
drivers/pinctrl/sprd/pinctrl-sprd.c:846:22: warning: implicit conversion
from enumeration type 'enum sprd_pinconf_params' to different
enumeration type 'enum pin_config_param' [-Wenum-conversion]
{"sprd,sleep-mode", SPRD_PIN_CONFIG_SLEEP_MODE, 0},
~ ^~~~~~~~~~~~~~~~~~~~~~~~~~
It is expected that pinctrl drivers can extend pin_config_param because
of the gap between PIN_CONFIG_END and PIN_CONFIG_MAX so this conversion
isn't an issue. Most drivers that take advantage of this define the
PIN_CONFIG variables as constants, rather than enumerated values. Do the
same thing here so that Clang no longer warns.
Link: https://github.com/ClangBuiltLinux/linux/issues/138 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Baolin Wang <baolin.wang@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
It's reported that the garbled sound on HP Envy x360 13z-ag000 (Ryzen
Laptop) is fixed by the same workaround applied to other AMD chips.
Update the driver_data entry for Raven (1022:15e3) to use the newly
introduced preset, AZX_DCAPS_PRESET_AMD_SB. Since it already contains
AZX_DCAPS_PM_RUNTIME, we can drop that bit, too.
Reported-and-tested-by: Dennis Padiernos <depadiernos@gmail.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20190920073040.31764-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
While the CSV3 field of the ID_AA64_PFR0 CPU ID register can be checked
to see if a CPU is susceptible to Meltdown and therefore requires kpti
to be enabled, existing CPUs do not implement this field.
We therefore whitelist all unaffected Cortex-A CPUs that do not implement
the CSV3 field.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The function only consists of a single switch case block without a
default case. Unsupported control requests are indicated by the -EINVAL
return code trough the last return statement at the end of the function. So
exiting just the switch case block returns the -EINVAL error code but the
hue control is supported and a zero should be returned instead.
Replace the break by a 'return 0' to fix this behaviour.
Fixes: d183e4efcae8 ("[media] v4l: tvp5150: Add missing break in set
control handler")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Probe responses were sent to the multicast station while
they should be routed to the broadcast station.
This has no negative effect since the frame was still
routed to the right queue, but it looked very fishy
to send a frame to a (queue, station) tuple where
'queue' is not mapped to 'station'.
Fixes: 7c305de2b954 ("iwlwifi: mvm: Direct multicast frames to the correct station") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
As reported by the OpenWRT team, write requests sometimes fail on some
platforms.
Currently to check the state chip_ready() is used correctly as described by
the flash memory S29GL256P11TFI01 datasheet.
Also chip_good() is used to check if the write is succeeded and it was
implemented by the commit fb4a90bfcd6d8 ("[MTD] CFI-0002 - Improve error
checking").
But actually the write failure is caused on some platforms and also it can
be fixed by using chip_good() to check the state and retry instead.
Also it seems that it is caused after repeated about 1,000 times to retry
the write one word with the reset command.
By using chip_good() to check the state to be done it can be reduced the
retry with reset.
It is depended on the actual flash chip behavior so the root cause is
unknown.
The syzbot fuzzer has reported a pair of problems in the
hidraw_ioctl() function: slab-out-of-bounds read and use-after-free
read. An example of the first:
BUG: KASAN: slab-out-of-bounds in strlen+0x79/0x90 lib/string.c:525
Read of size 1 at addr ffff8881c8035f38 by task syz-executor.4/2833
It turns out the fault was caused by a bug in the HID Logitech driver,
which violates the requirement that every pathway calling
hid_hw_start() must also call hid_hw_stop(). This patch fixes the bug
by making sure the requirement is met.
Reported-and-tested-by: syzbot+3cbe5cd105d2ad56a1df@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The sony driver is not properly cleaning up from potential failures in
sony_input_configured. Currently it calls hid_hw_stop, while hid_connect
is still running. This is not a good idea, instead hid_hw_stop should
be moved to sony_probe. Similar changes were recently made to Logitech
drivers, which were also doing improper cleanup.
The syzbot fuzzer provoked a general protection fault in the
hid-prodikeys driver:
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.3.0-rc5+ #28
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Workqueue: usb_hub_wq hub_event
RIP: 0010:pcmidi_submit_output_report drivers/hid/hid-prodikeys.c:300 [inline]
RIP: 0010:pcmidi_set_operational drivers/hid/hid-prodikeys.c:558 [inline]
RIP: 0010:pcmidi_snd_initialise drivers/hid/hid-prodikeys.c:686 [inline]
RIP: 0010:pk_probe+0xb51/0xfd0 drivers/hid/hid-prodikeys.c:836
Code: 0f 85 50 04 00 00 48 8b 04 24 4c 89 7d 10 48 8b 58 08 e8 b2 53 e4 fc
48 8b 54 24 20 48 b8 00 00 00 00 00 fc ff df 48 c1 ea 03 <80> 3c 02 00 0f
85 13 04 00 00 48 ba 00 00 00 00 00 fc ff df 49 8b
The problem is caused by the fact that pcmidi_get_output_report() will
return an error if the HID device doesn't provide the right sort of
output report, but pcmidi_set_operational() doesn't bother to check
the return code and assumes the function call always succeeds.
This patch adds the missing check and aborts the probe operation if
necessary.
Reported-and-tested-by: syzbot+1088533649dafa1c9004@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The upstream kernel commit cited below modified the workqueue in the
new CQ API to be bound to a specific CPU (instead of being unbound).
This caused ALL users of the new CQ API to use the same bound WQ.
Specifically, MAD handling was severely delayed when the CPU bound
to the WQ was busy handling (higher priority) interrupts.
This caused a delay in the MAD "heartbeat" response handling,
which resulted in ports being incorrectly classified as "down".
To fix this, add a new "unbound" WQ type to the new CQ API, so that users
have the option to choose either a bound WQ or an unbound WQ.
For MADs, choose the new "unbound" WQ.
Fixes: b7363e67b23e ("IB/device: Convert ib-comp-wq to be CPU-bound") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.m> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
There's a bug in skiboot that causes the OPAL_XIVE_ALLOCATE_IRQ call
to return the 32-bit value 0xffffffff when OPAL has run out of IRQs.
Unfortunatelty, OPAL return values are signed 64-bit entities and
errors are supposed to be negative. If that happens, the linux code
confusingly treats 0xffffffff as a valid IRQ number and panics at some
point.
A fix was recently merged in skiboot:
e97391ae2bb5 ("xive: fix return value of opal_xive_allocate_irq()")
but we need a workaround anyway to support older skiboots already
in the field.
Internally convert 0xffffffff to OPAL_RESOURCE which is the usual error
returned upon resource exhaustion.
There are devices which require low connection intervals for usable operation
including keyboards and mice. Forcing a static connection interval for
these types of devices has an impact in latency and causes a regression.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Observed crash in some scenarios when assertion has occurred,
this is because hw structure is freed and is tried to get
accessed in some functions where null check is already
present. So, avoided the crash by making the hw to NULL after
freeing.
Signed-off-by: Sanjay Konduri <sanjay.konduri@redpinesignals.com> Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
(cherry picked from commit abd39c6ded9db53aa44c2540092bdd5fb6590fa8) Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Acked-by: Tyler Hicks <tyhicks@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Nicolas Dichtel [Fri, 6 Sep 2019 09:54:00 +0000 (11:54 +0200)]
ipv6: fix neighbour resolution with raw socket
BugLink: https://bugs.launchpad.net/bugs/1834465
The scenario is the following: the user uses a raw socket to send an ipv6
packet, destinated to a not-connected network, and specify a connected nh.
Here is the corresponding python script to reproduce this scenario:
fd00:175::/64 is a connected route and fd00:200::fa is not a connected
host.
With this scenario, the kernel starts by sending a NS to resolve
fd00:175::2. When it receives the NA, it flushes its queue and try to send
the initial packet. But instead of sending it, it sends another NS to
resolve fd00:200::fa, which obvioulsy fails, thus the packet is dropped. If
the user sends again the packet, it now uses the right nh (fd00:175::2).
The problem is that ip6_dst_lookup_neigh() uses the rt6i_gateway, which is
:: because the associated route is a connected route, thus it uses the dst
addr of the packet. Let's use rt6_nexthop() to choose the right nh.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(backported from commit 2c6b55f45d53420d8310d41310e0e2cd41fe073f)
[nicolas.dichtel:
The upstream patch was slightly modified because ip6_dst_lookup_neigh()
does not exist in v4.15. It has been introduced in v4.18 by the upstream
commit f8a1b43b709d ("net/ipv6: Create a neigh_lookup for FIB entries"). In
fact, ip6_dst_lookup_neigh() just calls ip6_neigh_lookup().] Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
rt6_nexthop() will be used by ip6_dst_lookup_neigh(), which uses const
variables.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Reported-by: kbuild test robot <lkp@intel.com> Acked-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(backported from commit 9b1c1ef13b35fa35051b635ca9fbda39fe6bbc70) Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
UBUNTU: SAUCE: selftests: net: replace AF_MAX with INT_MAX in socket.c
BugLink: https://bugs.launchpad.net/bugs/1842023
Use INT_MAX instead of AF_MAX, since libc might have a smaller value
of AF_MAX than the kernel, what causes the test to fail.
Signed-off-by: Marcelo Henrique Cerri <marcelo.cerri@canonical.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Hui Wang [Mon, 2 Sep 2019 04:28:00 +0000 (06:28 +0200)]
ALSA: hda - Define a fallback_pin_fixup_tbl for alc269 family
BugLink: https://bugs.launchpad.net/bugs/1842265
We have another Dell laptop which needs the DELL4_MIC_NO_PRESENCE,
and this laptop has different pincfg definitions from existing
ones in the pintbl, rather adding a new entry, let us define
a tbl in the fallback_pin_fixup_tbl and this tbl will match
all dell machines with alc289 codec and the pins of 0x19 and 0x1b
are undef by default.
Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
(backported from commit 7c0a69394c265f2bb674c3f5daadfdd5c15ea0d1) Signed-off-by: Hui Wang <hui.wang@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Hui Wang [Mon, 2 Sep 2019 04:28:00 +0000 (06:28 +0200)]
ALSA: hda - Expand pin_match function to match upcoming new tbls
BugLink: https://bugs.launchpad.net/bugs/1842265
With the existing pintbl, we already have many entries in it. it is
better to figure out a new way to reduce the size of the pintbl.
We plan to define a new tbl which will match more machines with a
single tbl, To do that, this function doesn't need to match all valid
pins between machine and tbl, it just needs to match all pins defined
in the tbl with the machine.
And the plan is to move some tbls from pin_fixup_tbl to
fallback_pin_fixup_tbl gradually.
Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
(backported from commit 0fc1e447e9e474c2460df8d0378f899b8813e1d2) Signed-off-by: Hui Wang <hui.wang@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
UBUNTU: SAUCE: kbuild: add -fcf-protection=none when using retpoline flags
BugLink: https://bugs.launchpad.net/bugs/1843291
The gcc -fcf-protection=branch option is not compatible with
-mindirect-branch=thunk-extern. The latter is used when
CONFIG_RETPOLINE is selected, and this will fail to build with
a gcc which has -fcf-protection=branch enabled by default. Adding
-fcf-protection=none when building with retpoline enabled
prevents such build failures.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
(cherry picked from commit 29be86d7f9cb18df4123f309ac7857570513e8bc) Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Colin Ian King <colin.king@canonical.com> Acked-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1842774
Add detection for machine types 0x8562 and 8x8561 and set the ELF platform
name to z15. Add the miscellaneous-instruction-extension 3 facility to
the list of facilities for z15.
And allow to generate code that only runs on a z15 machine.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
(cherry picked from commit a0e2251132995b962281aa80ab54a9288f9e0b6b) Signed-off-by: Frank Heimes <frank.heimes@canonical.com> Acked-by: Sultan Alsawaf <sultan.alsawaf@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On embedded environments with hard memory limits it is a normal although
rare case when skb can't be allocated on rx part under high traffic.
In such OOM cases napi_complete_done() was not called.
So the napi object became in an invalid state like it is "scheduled".
Kernel do not re-schedules the poll of that napi object.
Consequently, kernel can not remove that object the system hangs on
`ifconfig down` waiting for a poll.
We are fixing this by gracefully closing napi poll routine with correct
invocation of napi_complete_done.
This was reproduced with artificially failing the allocation of skb to
simulate an "out of memory" error case and check that traffic does
not get stuck.
Fixes: 970a2e9864b0 ("net: ethernet: aquantia: Vector operations") Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently, the ibmvnic driver will not schedule device resets
if the device is being removed, but does not check the device
state before the reset is actually processed. This leads to a race
where a reset is scheduled with a valid device state but is
processed after the driver has been removed, resulting in an oops.
Fix this by checking the device state before processing a queued
reset event.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com> Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com> Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Simplify the check in physdev_mt_check() to emit an error message
only when passed an invalid chain (ie, NF_INET_LOCAL_OUT).
This avoids cluttering up the log with errors against valid rules.
For large/heavily modified rulesets, current behavior can quickly
overwhelm the ring buffer, because this function gets called on
every change, regardless of the rule that was changed.
When showing metadata about a single program by invoking
"bpftool prog show PROG", the file descriptor referring to the program
is not closed before returning from the function. Let's close it.
Christoph Paasch [Fri, 13 Sep 2019 20:08:19 +0000 (13:08 -0700)]
tcp: Don't dequeue SYN/FIN-segments from write-queue
BugLink: https://bugs.launchpad.net/bugs/1845266
If a SYN/FIN-segment is on the write-queue, skb->len is 0, but the
segment actually has been transmitted. end_seq and seq of the tcp_skb_cb
in that case will indicate this difference.
We should not remove such segments from the write-queue as we might be
in SYN_SENT-state and a retransmission-timer is running. When that one
fires, packets_out will be 1, but the write-queue would be empty,
resulting in:
The problem is that we are removing an skb from the write-queue that
could have been referenced by the sk_send_head. Thus, we need to check
for the send_head's sanity after removing it.
This patch needs to be backported only to 4.14 and older (among those
that applied the backport of fdfc5c8594c2).
Fixes: fdfc5c8594c2 ("tcp: remove empty skb from write queue in error cases") Cc: Eric Dumazet <edumazet@google.com> Cc: Jason Baron <jbaron@akamai.com> Cc: Vladimir Rutsky <rutsky@google.com> Cc: Soheil Hassas Yeganeh <soheil@google.com> Cc: Neal Cardwell <ncardwell@google.com> Signed-off-by: Christoph Paasch <cpaasch@apple.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commmit eab09532d400 ("binfmt_elf: use ELF_ET_DYN_BASE only for PIE"),
made changes in the rare case when the ELF loader was directly invoked
(e.g to set a non-inheritable LD_LIBRARY_PATH, testing new versions of
the loader), by moving into the mmap region to avoid both ET_EXEC and
PIE binaries. This had the effect of also moving the brk region into
mmap, which could lead to the stack and brk being arbitrarily close to
each other. An unlucky process wouldn't get its requested stack size
and stack allocations could end up scribbling on the heap.
This is illustrated here. In the case of using the loader directly, brk
(so helpfully identified as "[heap]") is allocated with the _loader_ not
the binary. For example, with ASLR entirely disabled, you can see this
more clearly:
The solution is to move brk out of mmap and into ELF_ET_DYN_BASE since
nothing is there in the direct loader case (and ET_EXEC is still far
away at 0x400000). Anything that ran before should still work (i.e.
the ultimately-launched binary already had the brk very far from its
text, so this should be no different from a COMPAT_BRK standpoint). The
only risk I see here is that if someone started to suddenly depend on
the entire memory space lower than the mmap region being available when
launching binaries via a direct loader execs which seems highly
unlikely, I'd hope: this would mean a binary would _not_ work when
exec()ed normally.
(Note that this is only done under CONFIG_ARCH_HAS_ELF_RANDOMIZATION
when randomization is turned on.)
Link: http://lkml.kernel.org/r/20190422225727.GA21011@beast Link: https://lkml.kernel.org/r/CAGXu5jJ5sj3emOT2QPxQkNQk0qbU6zEfu9=Omfhx_p0nCKPSjA@mail.gmail.com Fixes: eab09532d400 ("binfmt_elf: use ELF_ET_DYN_BASE only for PIE") Signed-off-by: Kees Cook <keescook@chromium.org> Reported-by: Ali Saidi <alisaidi@amazon.com> Cc: Ali Saidi <alisaidi@amazon.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jann Horn <jannh@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Frank van der Linden <fllinden@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
projects / mirror_ubuntu-bionic-kernel.git / log