The rxe driver works as follows:
* The send queue, receive queue and completion queues are implemented as
circular buffers.
* ib_post_send() and ib_post_recv() calls are serialized through a spinlock.
* Removing elements from various queues happens from tasklet
context. Tasklets are guaranteed to run on at most one CPU. This serializes
access to these queues. See also rxe_completer(), rxe_requester() and
rxe_responder().
* rxe_completer() processes the skbs queued onto qp->resp_pkts.
* rxe_requester() handles the send queue (qp->sq.queue).
* rxe_responder() processes the skbs queued onto qp->req_pkts.
Since rxe_drain_req_pkts() processes qp->req_pkts, calling
rxe_drain_req_pkts() from rxe_requester() is racy. Hence this patch.
The following sequence:
* Change queue pair state into IB_QPS_ERR.
* Post a work request on the queue pair.
Triggers the following race condition in the rdma_rxe driver:
* rxe_qp_error() triggers an asynchronous call of rxe_completer(), the function
that examines the QP send queue.
* rxe_post_send() posts a work request on the QP send queue.
If rxe_completer() runs prior to rxe_post_send(), it will drain the send
queue and the driver will assume no further action is necessary.
However, once we post the send to the send queue, because the queue is
in error, no send completion will ever happen and the send will get
stuck. In order to process the send, we need to make sure that
rxe_completer() gets run after a send is posted to a queue pair in an
error state. This patch ensures that happens.
Running the compaction_test sometimes results in out-of-memory
failures. When I debugged this, it turned out that the code to
reset the number of hugepages to the initial value is simply
broken since we write into an open sysctl file descriptor
multiple times without seeking back to the start.
aarch64-linux-gnu-gcc -Wl,-no-as-needed -Wall
-lpthread seccomp_bpf.c -o seccomp_bpf
seccomp_bpf.c: In function 'tracer_ptrace':
seccomp_bpf.c:1720:12: error: '__NR_open' undeclared
(first use in this function)
if (nr == __NR_open)
^~~~~~~~~
seccomp_bpf.c:1720:12: note: each undeclared identifier is reported
only once for each function it appears in
In file included from seccomp_bpf.c:48:0:
seccomp_bpf.c: In function 'TRACE_syscall_ptrace_syscall_dropped':
seccomp_bpf.c:1795:39: error: '__NR_open' undeclared
(first use in this function)
EXPECT_SYSCALL_RETURN(EPERM, syscall(__NR_open));
^
open(2) is a legacy syscall, replaced with openat(2) since 2.6.16.
Thus new architectures in the kernel, such as arm64, don't implement
these legacy syscalls.
The ev_file is an optional parameter for CQ creation. If the parameter
is not passed, the ev_file pointer will be NULL. Using that pointer
to set the cq_context will result in an OOPs.
Verify that ev_file is not NULL before using.
Cc: <stable@vger.kernel.org> # 4.14.x Fixes: 9ee79fce3642 ("IB/core: Add completion queue (cq) object actions") Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Reviewed-by: Ira Weiny <ira.weiny@intel.com> Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The change of slid from u16 to u32 results in sizeof(struct ib_wc)
cross 64B boundary, which causes more cache misses. This patch
rearranges the fields and remain the size to 64B.
Allocating steerable UD QPs depends on having at least one IB port,
while releasing those QPs does not.
As a result, when there are only ETH ports, the IB (RoCE) driver
requests releasing a qp range whose base qp is zero, with
qp count zero.
When SR-IOV is enabled, and the VF driver is running on a VM over
a hypervisor which treats such qp release calls as errors
(rather than NOPs), we see lines in the VM message log like:
mlx4_core 0002:00:02.0: Failed to release qp range base:0 cnt:0
Fix this by adding a check for a zero count in mlx4_release_qp_range()
(which thus treats releasing 0 qps as a nop), and eliminating the
check for device managed flow steering when releasing steerable UD QPs.
(Freeing ib_uc_qpns_bitmap unconditionally is also OK, since it
remains NULL when steerable UD QPs are not allocated).
Fixes: 4196670be786 ("IB/mlx4: Don't allocate range of steerable UD QPs for Ethernet-only device") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The request builder was using the incorrect inlines to
build the request header resulting in incorrect data
in the atomic header.
Fix by using the appropriate inlines to create the request.
Fixes: 261a4351844b ("IB/qib,IB/hfi: Use core common header file") Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The ib_write_umad() is protected by taking the umad file mutex.
However, it accesses file->port->ib_dev -- which is protected only by the
port's mutex (field file_mutex).
The ib_umad_remove_one() calls ib_umad_kill_port() which sets
port->ib_dev to NULL under the port mutex (NOT the file mutex).
It then sets the mad agent to "dead" under the umad file mutex.
This is a race condition -- because there is a window where
port->ib_dev is NULL, while the agent is not "dead".
This commit therefore adds EXPORT_SYMBOL_GPL() for each to allow them to
be used by GPL-licensed kernel modules.
Reported-by: Bart Van Assche <Bart.VanAssche@wdc.com> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
In the event of a command failure, cxlflash returns the failure to the upper
layers to process. After processing the error, when the command is queued
again, the private command structure will not be zeroed and the ioasc could be
stale. Per the SISLite specification, the AFU only sets the ioasc in the
presence of a failure. Thus, even though the original command succeeds the
second time, the command is considered a failure due to stale ioasc. This
cycle repeats indefinitely and can cause a hang or IO failure.
To fix the issue, clear the ioasc before queuing any command.
[mkp: added Cc: stable per request]
Fixes: 479ad8e9d48c ("scsi: cxlflash: Remove zeroing of private command data") Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com> Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
In test cases where an instance of the driver is detached and
reattached, the driver will crash on reattachment. There is a compound
if statement that will skip over the bar setup if the pci_resource_start
call is not successful. The driver erroneously returns success to its
bar setup in this scenario even though the bars aren't properly
configured.
Rework the offending code segment for proper initialization steps. If
the pci_resource_start call fails, -ENOMEM is now returned.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
If scsi_eh_scmd_add() is called concurrently with
scsi_host_queue_ready() while shost->host_blocked > 0 then it can
happen that neither function wakes up the SCSI error handler. Fix
this by making every function that decreases the host_busy counter
wake up the error handler if necessary and by protecting the
host_failed checks with the SCSI host lock.
Reported-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
References: https://marc.info/?l=linux-kernel&m=150461610630736 Fixes: commit 746650160866 ("scsi: convert host_busy to atomic_t") Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Reviewed-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com> Tested-by: Stuart Hayes <stuart.w.hayes@gmail.com> Cc: Konstantin Khorenko <khorenko@virtuozzo.com> Cc: Stuart Hayes <stuart.w.hayes@gmail.com> Cc: Pavel Tikhomirov <ptikhomirov@virtuozzo.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.com> Cc: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
__unregister_ftrace_function_probe() will incorrectly parse the glob filter
because it resets the search variable that was setup by filter_parse_regex().
Al Viro reported this:
After that call of filter_parse_regex() we could have func_g.search not
equal to glob only if glob started with '!' or '*'. In the former case
we would've buggered off with -EINVAL (not = 1). In the latter we
would've set func_g.search equal to glob + 1, calculated the length of
that thing in func_g.len and proceeded to reset func_g.search back to
glob.
Suppose the glob is e.g. *foo*. We end up with
func_g.type = MATCH_MIDDLE_ONLY;
func_g.len = 3;
func_g.search = "*foo";
Feeding that to ftrace_match_record() will not do anything sane - we
will be looking for names containing "*foo" (->len is ignored for that
one).
Setting si_code to 0 is the same a setting si_code to SI_USER which is definitely
not correct. With si_code set to SI_USER si_pid and si_uid will be copied to
userspace instead of si_addr. Which is very wrong.
So fix this by using a sensible si_code (SEGV_MAPERR) for this failure.
Fixes: b920de1b77b7 ("mn10300: add the MN10300/AM33 architecture to the kernel") Cc: David Howells <dhowells@redhat.com> Cc: Masakazu Urade <urade.masakazu@jp.panasonic.com> Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
fsnotify pins a watched directory inode in cache, but if directory dentry
is released, new lookup will allocate a new dentry and a new inode.
Directory events will be notified on the new inode, while fsnotify listener
is watching the old pinned inode.
Hash all directory inodes to reuse the pinned inode on lookup. Pure upper
dirs are hashes by real upper inode, merge and lower dirs are hashed by
real lower inode.
The reference to lower inode was being held by the lower dentry object
in the overlay dentry (oe->lowerstack[0]). Releasing the overlay dentry
may drop lower inode refcount to zero. Add a refcount on behalf of the
overlay inode to prevent that.
As a by-product, hashing directory inodes also detects multiple
redirected dirs to the same lower dir and uncovered redirected dir
target on and returns -ESTALE on lookup.
The reported issue dates back to initial version of overlayfs, but this
patch depends on ovl_inode code that was introduced in kernel v4.13.
As a writable mount, it is not expected for overlayfs to return
EINVAL/EROFS for fsync, even if dir/file is not changed.
This commit fixes the case of fsync of directory, which is easier to
address, because overlayfs already implements fsync file operation for
directories.
The problem reported by Raphael is that new PostgreSQL 10.0 with a
database in overlayfs where lower layer in squashfs fails to start.
The failure is due to fsync error, when PostgreSQL does fsync on all
existing db directories on startup and a specific directory exists
lower layer with no changes.
When work dir creation fails, a warning is emitted and overlay is
mounted r/o. Trying to remount r/w will fail with no work dir.
When index dir creation fails, the same warning is emitted and overlay
is mounted r/o, but trying to remount r/w will succeed. This may cause
unintentional corruption of filesystem consistency.
Adjust the behavior of index dir creation failure to that of work dir
creation failure and do not allow to remount r/w. User needs to state
an explicitly intention to work without an index by mounting with
option 'index=off' to allow r/w mount with no index dir.
When mounting with option 'index=on' and no 'upperdir', index is
implicitly disabled, so do not warn about no file handle support.
The issue was introduced with inodes index feature in v4.13, but this
patch will not apply cleanly before ovl_fill_super() re-factoring in
v4.15.
Fixes: 02bcd1577400 ("ovl: introduce the inodes index dir feature") Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
A NULL pointer reference kernel bug was observed when
acpi_nfit_add_dimm() called in acpi_nfit_register_dimms() failed. This
error path does not set nfit_mem->nvdimm, but the 2nd
list_for_each_entry() loop in the function assumes it's always set. Add
a check to nfit_mem->nvdimm.
Fixes: ba9c8dd3c222 ("acpi, nfit: add dimm device notification support") Signed-off-by: Toshi Kani <toshi.kani@hpe.com> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
There's no need to be printing a raw kernel pointer to the kernel log at
every boot. So just remove it, and change the whole message to use the
correct dev_info() call at the same time.
Reported-by: Wang Qize <wang_qize@venustech.com.cn> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
We store a SW state of the t11_t12 timing in 100usec units but have to
program it in 100msec as required by HW. The rounding used during
programming means there will be a mismatch between the SW and HW states
of this value triggering a "PPS state mismatch" error. Avoid this by
storing the already rounded-up value in the SW state.
Note that we still calculate panel_power_cycle_delay with the finer
100usec granularity to avoid any needless waits using that version of
the delay.
This patch adds Ethernet aliases in the Marvell Armada 7040 DB, 8040 DB
and 8040 mcbin device trees so that the bootloader setup the MAC
addresses correctly.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message, small fixes] Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Linus reported that GCC-7.3 generated a switch-table construct that
confused objtool. It turns out that, in particular due to KASAN, it is
possible to have unrelated .rodata usage in between the .rodata setup
for the switch-table and the following indirect jump.
The simple linear reverse search from the indirect jump would hit upon
the KASAN .rodata usage first and fail to find a switch_table,
resulting in a spurious 'sibling call with modified stack frame'
warning.
Fix this by creating a 'jump-stack' which we can 'unwind' during
reversal, thereby skipping over much of the in-between code.
This is not fool proof by any means, but is sufficient to make the
known cases work. Future work would be to construct more comprehensive
flow analysis code.
arch/x86/kernel/head64.o: In function `sanitize_boot_params':
arch/x86/include/asm/bootparam_utils.h:37: undefined reference to `__ubsan_handle_type_mismatch_v1'
because Clang and GCC 8 slightly changed ABI for 'type mismatch' errors.
Compiler now uses new __ubsan_handle_type_mismatch_v1() function with
slightly modified 'struct type_mismatch_data'.
Let's add new 'struct type_mismatch_data_common' which is independent from
compiler's layout of 'struct type_mismatch_data'. And make
__ubsan_handle_type_mismatch[_v1]() functions transform compiler-dependent
type mismatch data to our internal representation. This way, we can
support both old and new compilers with minimal amount of change.
- The global variable 'clock_event_ddata' is overwritten each time the
init function is invoked.
This is fixed with a kmemdup() instead of assigning the global variable. That
prevents a memory corruption when several timers are defined in the DT.
- The clockevent's event_handler is NULL if the time framework does
not select the clockevent when registering it, this is fine but the init
code generates in any case an interrupt leading to dereference this
NULL pointer.
The stm32 timer works with shadow registers, a mechanism to cache the
registers. When a change is done in one buffered register, we need to
artificially generate an event to force the timer to copy the content
of the register to the shadowed register.
The auto-reload register (ARR) is one of the shadowed register as well as
the prescaler register (PSC), so in order to force the copy, we issue an
event which in turn leads to an interrupt and the NULL dereference.
This is fixed by inverting two lines where we clear the status register
before enabling the update event interrupt.
As this kernel crash is resulting from the combination of these two bugs,
the fixes are grouped into a single patch.
Tested-by: Benjamin Gaignard <benjamin.gaignard@st.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Acked-by: Benjamin Gaignard <benjamin.gaignard@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1515418139-23276-11-git-send-email-daniel.lezcano@linaro.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
After queue is frozen, dispatch still may happen, for example:
1) requests are submitted from several contexts
2) requests from all these contexts are inserted to queue, but may dispatch
to LLD in one of these paths, but other paths sill need to move on even all
these requests are completed(that means blk_mq_freeze_queue_wait() returns
at that time)
3) dispatch after queue freezing still moves on and causes use-after-free,
because request queue is freed
This patch quiesces queue after it is frozen, and makes sure all
in-progress dispatch are completed.
This patch fixes the following kernel crash when running heavy IOs vs.
deleting device:
Call bdev_get_queue(bdev) after bdev->bd_disk has been initialized
instead of just before that pointer has been initialized. This patch
avoids that the following command
pktsetup 1 /dev/sr0
triggers the following kernel crash:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000548
IP: pkt_setup_dev+0x2db/0x670 [pktcdvd]
CPU: 2 PID: 724 Comm: pktsetup Not tainted 4.15.0-rc4-dbg+ #1
Call Trace:
pkt_ctl_ioctl+0xce/0x1c0 [pktcdvd]
do_vfs_ioctl+0x8e/0x670
SyS_ioctl+0x3c/0x70
entry_SYSCALL_64_fastpath+0x23/0x9a
Reported-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name> Fixes: commit ca18d6f769d2 ("block: Make most scsi_req_init() calls implicit") Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name> Cc: Maciej S. Szmigiero <mail@maciej.szmigiero.name> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Commit 523e1d399ce0 ("block: make gendisk hold a reference to its queue")
modified add_disk() and disk_release() but did not update any of the
error paths that trigger a put_disk() call after disk->queue has been
assigned. That introduced the following behavior in the pktcdvd driver
if pkt_new_dev() fails:
Since disk_release() calls blk_put_queue() anyway if disk->queue != NULL,
fix this by removing the blk_cleanup_queue() call from the pkt_setup_dev()
error path.
Fixes: commit 523e1d399ce0 ("block: make gendisk hold a reference to its queue") Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Cc: Tejun Heo <tj@kernel.org> Cc: Maciej S. Szmigiero <mail@maciej.szmigiero.name> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Without such a range, gpiolib fails with -EPROBE_DEFER, pending the
addition of the range. So, without a range, gpiolib will keep
deferring indefinitely.
When using mcp23s08 module with gpio-keys, often (50% of boots)
it fails to get irq numbers with message:
"gpio-keys keys: Unable to get irq number for GPIO 0, error -6".
Seems that irqs must be setup before devm_gpiochip_add_data().
When a GPIO is requested using gpiod_get_* APIs the intel pinctrl driver
switches the pin to GPIO mode and makes sure interrupts are routed to
the GPIO hardware instead of IOAPIC. However, if the GPIO is used
directly through irqchip, as is the case with many I2C-HID devices where
I2C core automatically configures interrupt for the device, the pin is
not initialized as GPIO. Instead we rely that the BIOS configures the
pin accordingly which seems not to be the case at least in Asus X540NA
SKU3 with Focaltech touchpad.
When the pin is not properly configured it might result weird behaviour
like interrupts suddenly stop firing completely and the touchpad stops
responding to user input.
Fix this by properly initializing the pin to GPIO mode also when it is
used directly through irqchip.
Fixes: 7981c0015af2 ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support") Reported-by: Daniel Drake <drake@endlessm.com> Reported-and-tested-by: Chris Chiu <chiu@endlessm.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Fix an uninitialized variable warning in the Octeon EDAC driver, as seen
in MIPS cavium_octeon_defconfig builds since v4.14 with Codescape GNU
Tools 2016.05-03:
drivers/edac/octeon_edac-lmc.c In function ‘octeon_lmc_edac_poll_o2’:
drivers/edac/octeon_edac-lmc.c:87:24: warning: ‘((long unsigned int*)&int_reg)[1]’ may \
be used uninitialized in this function [-Wmaybe-uninitialized]
if (int_reg.s.sec_err || int_reg.s.ded_err) {
^
Iinitialise the whole int_reg variable to zero before the conditional
assignments in the error injection case.
Return 0 if the operation was successful, not the userspace memory
value. Check that userspace value equals passed oldval, not itself.
Don't update *uval if the value wasn't read from userspace memory.
This fixes process hang due to infinite loop in futex_lock_pi.
It also fixes a bunch of glibc tests nptl/tst-mutexpi*.
Since version 4.9, the kernel automatically breaks printk calls into
multiple newlines unless pr_cont is used. Fix the alpha stacktrace code,
so that it prints stack trace in four columns, as it was initially
intended.
Fix the typo (mixed up arguments) in the EXC macro in the futex
definitions introduced by commit ca282f697381 (alpha: add a
helper for emitting exception table entries).
Signed-off-by: Michael Cree <mcree@orcon.net.nz> Signed-off-by: Matt Turner <mattst88@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
There was a typo in the new version of put_tv32() that caused an unguarded
access of a user space pointer, and failed to return the correct result in
gettimeofday(), wait4(), usleep_thread() and old_adjtimex().
This fixes it to give the correct behavior again.
Fixes: 1cc6c4635e9f ("osf_sys.c: switch handling of timeval32/itimerval32 to copy_{to,from}_user()") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
On alpha, a process will crash if it attempts to start a thread and a
signal is delivered at the same time. The crash can be reproduced with
this program: https://cygwin.com/ml/cygwin/2014-11/msg00473.html
The reason for the crash is this:
* we call the clone syscall
* we go to the function copy_process
* copy process calls copy_thread_tls, it is a wrapper around copy_thread
* copy_thread sets the tls pointer: childti->pcb.unique = regs->r20
* copy_thread sets regs->r20 to zero
* we go back to copy_process
* copy process checks "if (signal_pending(current))" and returns
-ERESTARTNOINTR
* the clone syscall is restarted, but this time, regs->r20 is zero, so
the new thread is created with zero tls pointer
* the new thread crashes in start_thread when attempting to access tls
The comment in the code says that setting the register r20 is some
compatibility with OSF/1. But OSF/1 doesn't use the CLONE_SETTLS flag, so
we don't have to zero r20 if CLONE_SETTLS is set. This patch fixes the bug
by zeroing regs->r20 only if CLONE_SETTLS is not set.
While reviewing the signal sending on openrisc the do_unaligned_access
function stood out because it is obviously wrong. A comment about an
si_code set above when actually si_code is never set. Leading to a
random si_code being sent to userspace in the event of an unaligned
access.
Looking further SIGBUS BUS_ADRALN is the proper pair of signal and
si_code to send for an unaligned access. That is what other
architectures do and what is required by posix.
Given that do_unaligned_access is broken in a way that no one can be
relying on it on openrisc fix the code to just do the right thing.
This is because when the device is released in
platform_device_release(), we try to free
pdev.driver_override. This is a const string, hence
the crash.
Fix by using dynamic memory for pdev->driver_override.
Signed-off-by: John Garry <john.garry@huawei.com>
[Removed the free of driver_override from ipmi_si_remove_by_dev(). The
free is done in platform_device_release(), and would result in a double
free, and ipmi_si_remove_by_dev() is called by non-platform devices.] Signed-off-by: Corey Minyard <cminyard@mvista.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
BCM43341 devices soldered onto the PCB (non-removable) always (AFAICT)
use an UART connection for bluetooth. But they also advertise btsdio
support on their 3th sdio function, this causes 2 problems:
1) A non functioning BT HCI getting registered
2) Since the btsdio driver does not have suspend/resume callbacks,
mmc_sdio_pre_suspend will return -ENOSYS, causing mmc_pm_notify()
to react as if the SDIO-card is removed and since the slot is
marked as non-removable it will never get detected as inserted again.
Which results in wifi no longer working after a suspend/resume.
This commit fixes both by making btsdio ignore BCM43341 devices
when connected to a slot which is marked non-removable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The Toshiba Click Mini uses an i2c attached keyboard/touchpad combo
(single i2c_hid device for both) which has a vid:pid of 04F3:0401,
which is also used by a bunch of Elan touchpads which are handled by the
drivers/input/mouse/elan_i2c driver, but that driver deals with pure
touchpads and does not work for a combo device such as the one on the
Toshiba Click Mini.
The combo on the Mini has an ACPI id of ELAN0800, which is not claimed
by the elan_i2c driver, so check for that and if it is found do not ignore
the device. This fixes the keyboard/touchpad combo on the Mini not working
(although with the touchpad in mouse emulation mode).
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
pipe-user-pages-hard and pipe-user-pages-soft are only supposed to apply
to unprivileged users, as documented in both Documentation/sysctl/fs.txt
and the pipe(7) man page.
However, the capabilities are actually only checked when increasing a
pipe's size using F_SETPIPE_SZ, not when creating a new pipe. Therefore,
if pipe-user-pages-hard has been set, the root user can run into it and be
unable to create pipes. Similarly, if pipe-user-pages-soft has been set,
the root user can run into it and have their pipes limited to 1 page each.
Fix this by allowing the privileged override in both cases.
Link: http://lkml.kernel.org/r/20180111052902.14409-4-ebiggers3@gmail.com Fixes: 759c01142a5d ("pipe: limit the per-user amount of pages allocated in pipes") Signed-off-by: Eric Biggers <ebiggers@google.com> Acked-by: Kees Cook <keescook@chromium.org> Acked-by: Joe Lawrence <joe.lawrence@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: "Luis R . Rodriguez" <mcgrof@kernel.org> Cc: Michael Kerrisk <mtk.manpages@gmail.com> Cc: Mikulas Patocka <mpatocka@redhat.com> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
This reverts commit 92266d6ef60c ("async: simplify lowest_in_progress()")
which was simply wrong: In the case where domain is NULL, we now use the
wrong offsetof() in the list_first_entry macro, so we don't actually
fetch the ->cookie value, but rather the eight bytes located
sizeof(struct list_head) further into the struct async_entry.
On 64 bit, that's the data member, while on 32 bit, that's a u64 built
from func and data in some order.
I think the bug happens to be harmless in practice: It obviously only
affects callers which pass a NULL domain, and AFAICT the only such
caller is
and the ASYNC_COOKIE_MAX means that in practice we end up waiting for
the async_global_pending list to be empty - but it would break if
somebody happened to pass (void*)-1 as the data element to
async_schedule, and of course also if somebody ever does a
async_synchronize_cookie_domain(, NULL) with a "finite" cookie value.
Maybe the "harmless in practice" means this isn't -stable material. But
I'm not completely confident my quick git grep'ing is enough, and there
might be affected code in one of the earlier kernels that has since been
removed, so I'll leave the decision to the stable guys.
Link: http://lkml.kernel.org/r/20171128104938.3921-1-linux@rasmusvillemoes.dk Fixes: 92266d6ef60c "async: simplify lowest_in_progress()" Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Acked-by: Tejun Heo <tj@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Adam Wallis <awallis@codeaurora.org> Cc: Lai Jiangshan <laijs@cn.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Commit df04abfd181a ("fs/proc/kcore.c: Add bounce buffer for ktext
data") added a bounce buffer to avoid hardened usercopy checks. Copying
to the bounce buffer was implemented with a simple memcpy() assuming
that it is always valid to read from kernel memory iff the
kern_addr_valid() check passed.
A simple, but pointless, test case like "dd if=/proc/kcore of=/dev/null"
now can easily crash the kernel, since the former execption handling on
invalid kernel addresses now doesn't work anymore.
Also adding a kern_addr_valid() implementation wouldn't help here. Most
architectures simply return 1 here, while a couple implemented a page
table walk to figure out if something is mapped at the address in
question.
With DEBUG_PAGEALLOC active mappings are established and removed all the
time, so that relying on the result of kern_addr_valid() before
executing the memcpy() also doesn't work.
Therefore simply use probe_kernel_read() to copy to the bounce buffer.
This also allows to simplify read_kcore().
At least on s390 this fixes the observed crashes and doesn't introduce
warnings that were removed with df04abfd181a ("fs/proc/kcore.c: Add
bounce buffer for ktext data"), even though the generic
probe_kernel_read() implementation uses uaccess functions.
While looking into this I'm also wondering if kern_addr_valid() could be
completely removed...(?)
Mention the maximum voltages of the CEC and HPD lines. Since in the example
these lines are connected to a Raspberry Pi and the Rpi GPIO lines are 3.3V
it is a good idea to warn against directly connecting the HPD to the Raspberry
Pi's GPIO line.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
A typical code fragment was copied across many dvb-frontend drivers and
causes large stack frames when built with with CONFIG_KASAN on gcc-5/6/7:
drivers/media/dvb-frontends/cxd2841er.c:3225:1: error: the frame size of 3992 bytes is larger than 3072 bytes [-Werror=frame-larger-than=]
drivers/media/dvb-frontends/cxd2841er.c:3404:1: error: the frame size of 3136 bytes is larger than 3072 bytes [-Werror=frame-larger-than=]
drivers/media/dvb-frontends/stv0367.c:3143:1: error: the frame size of 4016 bytes is larger than 3072 bytes [-Werror=frame-larger-than=]
drivers/media/dvb-frontends/stv090x.c:3430:1: error: the frame size of 5312 bytes is larger than 3072 bytes [-Werror=frame-larger-than=]
drivers/media/dvb-frontends/stv090x.c:4248:1: error: the frame size of 4872 bytes is larger than 3072 bytes [-Werror=frame-larger-than=]
gcc-8 now solves this by consolidating the stack slots for the argument
variables, but on older compilers we can get the same behavior by taking
the pointer of a local variable rather than the inline function argument.
As smatch warned:
drivers/media/dvb-core/dvb_frontend.c:2468 dvb_frontend_handle_ioctl() error: uninitialized symbol 'err'.
The ioctl handler actually got a regression here: before changeset d73dcf0cdb95 ("media: dvb_frontend: cleanup ioctl handling logic"),
the code used to return -EOPNOTSUPP if an ioctl handler was not
implemented on a driver. After the change, it may return a random
value.
We get a lot of very large stack frames using gcc-7.0.1 with the default
-fsanitize-address-use-after-scope --param asan-stack=1 options, which can
easily cause an overflow of the kernel stack, e.g.
drivers/gpu/drm/i915/gvt/handlers.c:2434:1: warning: the frame size of 46176 bytes is larger than 3072 bytes
drivers/net/wireless/ralink/rt2x00/rt2800lib.c:5650:1: warning: the frame size of 23632 bytes is larger than 3072 bytes
lib/atomic64_test.c:250:1: warning: the frame size of 11200 bytes is larger than 3072 bytes
drivers/gpu/drm/i915/gvt/handlers.c:2621:1: warning: the frame size of 9208 bytes is larger than 3072 bytes
drivers/media/dvb-frontends/stv090x.c:3431:1: warning: the frame size of 6816 bytes is larger than 3072 bytes
fs/fscache/stats.c:287:1: warning: the frame size of 6536 bytes is larger than 3072 bytes
To reduce this risk, -fsanitize-address-use-after-scope is now split out
into a separate CONFIG_KASAN_EXTRA Kconfig option, leading to stack
frames that are smaller than 2 kilobytes most of the time on x86_64. An
earlier version of this patch also prevented combining KASAN_EXTRA with
KASAN_INLINE, but that is no longer necessary with gcc-7.0.1.
All patches to get the frame size below 2048 bytes with CONFIG_KASAN=y
and CONFIG_KASAN_EXTRA=n have been merged by maintainers now, so we can
bring back that default now. KASAN_EXTRA=y still causes lots of
warnings but now defaults to !COMPILE_TEST to disable it in
allmodconfig, and it remains disabled in all other defconfigs since it
is a new option. I arbitrarily raise the warning limit for KASAN_EXTRA
to 3072 to reduce the noise, but an allmodconfig kernel still has around
50 warnings on gcc-7.
I experimented a bit more with smaller stack frames and have another
follow-up series that reduces the warning limit for 64-bit architectures
to 1280 bytes (without CONFIG_KASAN).
With earlier versions of this patch series, I also had patches to address
the warnings we get with KASAN and/or KASAN_EXTRA, using a
"noinline_if_stackbloat" annotation.
That annotation now got replaced with a gcc-8 bugfix (see
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81715) and a workaround for
older compilers, which means that KASAN_EXTRA is now just as bad as
before and will lead to an instant stack overflow in a few extreme
cases.
This reverts parts of commit 3f181b4d8652 ("lib/Kconfig.debug: disable
-Wframe-larger-than warnings with KASAN=y"). Two patches in linux-next
should be merged first to avoid introducing warnings in an allmodconfig
build: 3cd890dbe2a4 ("media: dvb-frontends: fix i2c access helpers for KASAN") 16c3ada89cff ("media: r820t: fix r820t_write_reg for KASAN")
Do we really need to backport this?
I think we do: without this patch, enabling KASAN will lead to
unavoidable kernel stack overflow in certain device drivers when built
with gcc-7 or higher on linux-4.10+ or any version that contains a
backport of commit c5caf21ab0cf8. Most people are probably still on
older compilers, but it will get worse over time as they upgrade their
distros.
The warnings we get on kernels older than this should all be for code
that uses dangerously large stack frames, though most of them do not
cause an actual stack overflow by themselves.The asan-stack option was
added in linux-4.0, and commit 3f181b4d8652 ("lib/Kconfig.debug:
disable -Wframe-larger-than warnings with KASAN=y") effectively turned
off the warning for allmodconfig kernels, so I would like to see this
fix backported to any kernels later than 4.0.
I have done dozens of fixes for individual functions with stack frames
larger than 2048 bytes with asan-stack, and I plan to make sure that
all those fixes make it into the stable kernels as well (most are
already there).
Part of the complication here is that asan-stack (from 4.0) was
originally assumed to always require much larger stacks, but that
turned out to be a combination of multiple gcc bugs that we have now
worked around and fixed, but sanitize-address-use-after-scope (from
v4.10) has a much higher inherent stack usage and also suffers from at
least three other problems that we have analyzed but not yet fixed
upstream, each of them makes the stack usage more severe than it should
be.
With KASAN enabled the kernel has two different memset() functions, one
with KASAN checks (memset) and one without (__memset). KASAN uses some
macro tricks to use the proper version where required. For example
memset() calls in mm/slub.c are without KASAN checks, since they operate
on poisoned slab object metadata.
The issue is that clang emits memset() calls even when there is no
memset() in the source code. They get linked with improper memset()
implementation and the kernel fails to boot due to a huge amount of KASAN
reports during early boot stages.
The solution is to add -fno-builtin flag for files with KASAN_SANITIZE :=
n marker.
Link: http://lkml.kernel.org/r/8ffecfffe04088c52c42b92739c2bd8a0bcb3f5e.1516384594.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Nick Desaulniers <ndesaulniers@google.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Michal Marek <michal.lkml@markovi.net> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Bio iterated by set_bio_pages_uptodate() is raid56 internal one, so it
will never be a BIO_CLONED bio, and since this is called by end_io
functions, bio->bi_iter.bi_size is zero, we mustn't use
bio_for_each_segment() as that is a no-op if bi_size is zero.
Fixes: 6592e58c6b68e61f003a01ba29a3716e7e2e9484 ("Btrfs: fix write corruption due to bio cloning on raid5/6") Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
This function was introduced by 247e743cbe6e ("Btrfs: Use async helpers
to deal with pages that have been improperly dirtied") and it didn't do
any error handling then. This function might very well fail in ENOMEM
situation, yet it's not handled, this could lead to inconsistent state.
So let's handle the failure by setting the mapping error bit.
Signed-off-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
(1) In afs_alloc_volume(), remove duplicate server list build code. This
was already done by afs_alloc_server_list() which afs_alloc_volume()
previously called. This just results in twice as many VL RPCs.
(2) In afs_deliver_vl_get_entry_by_name_u(), use the number of server
records indicated by ->nServers in the UVLDB record returned by the
VL.GetEntryByNameU RPC call rather than scanning all NMAXNSERVERS
slots. Unused slots may contain garbage.
(3) In afs_alloc_server_list(), don't stop converting a UVLDB record into
a server list just because we can't look up one of the servers. Just
skip that server and go on to the next. If we can't look up any of
the servers then we'll fail at the end.
Without this patch, an attempt to view the umich.edu root cell using
something like "ls /afs/umich.edu" on a dynamic root (future patch) mount
or an autocell mount will result in ENOMEDIUM. The failure is due to kafs
not stopping after nServers'worth of records have been read, but then
trying to access a server with a garbage UUID and getting an error, which
aborts the server list build.
Fixes: d2ddc776a458 ("afs: Overhaul volume and server record caching and fileserver rotation") Reported-by: Jonathan Billings <jsbillings@jsbillings.org> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
afs_select_fileserver() ends the address cursor it is using in the case in
which we get some sort of network error and run out of addresses to iterate
through, before it jumps to try the next server. This also needs to be
done when the server aborts with some sort of error that means we should
try the next server.
Fix this by:
(1) Move the iterate_address afs_end_cursor() call to the next_server
case.
(2) End the cursor in the failed case.
(3) Make afs_end_cursor() clear the ->begun flag and ->addr pointer in the
address cursor.
(4) Make afs_end_cursor() able to be called on an already cleared cursor.
Without this, something like the following oops may occur:
AFS: Assertion failed 18446612134397189888 == 0 is false
0xffff88007c279f00 == 0x0 is false
------------[ cut here ]------------
kernel BUG at fs/afs/rotate.c:360!
RIP: 0010:afs_select_fileserver+0x79b/0xa30 [kafs]
Call Trace:
afs_statfs+0xcc/0x180 [kafs]
? p9_client_statfs+0x9e/0x110 [9pnet]
? _cond_resched+0x19/0x40
statfs_by_dentry+0x6d/0x90
vfs_statfs+0x1b/0xc0
user_statfs+0x4b/0x80
SYSC_statfs+0x15/0x30
SyS_statfs+0xe/0x10
entry_SYSCALL_64_fastpath+0x20/0x83
Fixes: d2ddc776a458 ("afs: Overhaul volume and server record caching and fileserver rotation") Reported-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
In afs_select_fileserver(), we need to clear the ->responded flag in the
address list when reusing it. We should also clear it in
afs_select_current_fileserver().
To this end, just memset() the object before initialising it.
Fixes: d2ddc776a458 ("afs: Overhaul volume and server record caching and fileserver rotation") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
afs_alloc_volume() needs to release the cell ref it obtained in the case of
an error. Fix this by adding an afs_put_cell() call into the error path.
This can triggered when a lookup for a cell in a dynamic root or an
autocell mount returns an error whilst trying to look up the server (such
as ENOMEDIUM). This results in an assertion failure oops when the module
is unloaded due to outstanding refs on a cell record.
Fixes: d2ddc776a458 ("afs: Overhaul volume and server record caching and fileserver rotation") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
When the watchdog device is suspended, its timeout is set to the maximum
value. During resume, the previously set timeout should be restored.
This does not work at the moment.
The suspend function calls
imx2_wdt_set_timeout(wdog, IMX2_WDT_MAX_TIME);
and resume reverts this by calling
imx2_wdt_set_timeout(wdog, wdog->timeout);
However, imx2_wdt_set_timeout() updates wdog->timeout. Therefore,
wdog->timeout is set to IMX2_WDT_MAX_TIME when we enter the resume
function.
Fix this by adding a new function __imx2_wdt_set_timeout() which
only updates the hardware settings. imx2_wdt_set_timeout() now calls
__imx2_wdt_set_timeout() and then saves the new timeout to
wdog->timeout.
During suspend, we call __imx2_wdt_set_timeout() directly so that
wdog->timeout won't be updated and we can restore the previous value
during resume. This approach makes wdog->timeout different from the
actual setting in the hardware which is usually not a good thing.
However, the two differ only while we're suspended and no kernel code is
running, so it should be ok in this case.
Signed-off-by: Martin Kaiser <martin@kaiser.cx> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The soc_compr_copy callback is currently broken. Since the
changes to move the compr_ops over to the component the return
value is not correctly propagated, always returning zero on
success rather than the number of bytes copied. This causes
user-space to stall continuously reading as it does not believe
it has received any data.
Furthermore, the changes to move the compr_ops over to the
component iterate through the list of components and will call
the copy callback for any that have compressed ops. There isn't
currently any consensus on the mechanism to combine the results
of multiple copy callbacks.
To fix this issue for now halt searching the component list when
we locate a copy callback and return the result of that single
callback. Additional work should probably be done to look at the
other ops, tidy things up, and work out if we want to support
multiple components on a single compressed, but this is the only
fix required to get things working again.
Fixes: 9e7e3738ab0e ("ASoC: snd_soc_component_driver has snd_compr_ops") Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
I got the following kernel warning when loading snd-soc-skl module on
Dell Latitude 7270 laptop:
memremap attempted on mixed range 0x0000000000000000 size: 0x0
WARNING: CPU: 0 PID: 484 at kernel/memremap.c:98 memremap+0x8a/0x180
Call Trace:
skl_nhlt_init+0x82/0xf0 [snd_soc_skl]
skl_probe+0x2ee/0x7c0 [snd_soc_skl]
....
It seems that the machine doesn't support the SKL DSP gives the empty
NHLT entry, and it triggers the warning. For avoiding it, let do the
zero check before calling memremap().
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
When restoring registers during runtime resume, we must not write to
I2S_TXDR which is the transmit FIFO as this queues up a sample to be
output and pushes all of the output channels down by one.
This can be demonstrated with the speaker-test utility:
for i in a b c; do speaker-test -c 2 -s 1; done
which should play a test through the left speaker three times but if the
I2S hardware starts runtime suspended the first sample will be played
through the right speaker.
Fix this by marking I2S_TXDR as volatile (which also requires marking it
as readble, even though it technically isn't). This seems to be the
most robust fix, the alternative of giving I2S_TXDR a default value is
more fragile since it does not prevent regcache writing to the register
in all circumstances.
While here, also fix the configuration of I2S_RXDR and I2S_FIFOLR; these
are not writable so they do not suffer from the same problem as I2S_TXDR
but reading from I2S_RXDR does suffer from a similar problem.
Fixes: f0447f6cbb20 ("ASoC: rockchip: i2s: restore register during runtime_suspend/resume cycle", 2016-09-07) Signed-off-by: John Keeping <john@metanate.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The ACPI/machine-driver code refactoring introduced in 4.13 introduced
a regression for cases where we need a DMI-based quirk to select the
machine driver (the BIOS reports an invalid HID). The fix is just to
make sure the results of the quirk are actually used.
Fixes: 54746dabf770 ('ASoC: Improve machine driver selection based on quirk data')
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=96691 Tested-by: Nicole Færber <nicole.faerber@dpin.de> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Commit 76d837a4c0f9 ("KVM: PPC: Book3S PR: Don't include SPAPR TCE code
on non-pseries platforms") added a reference to the globally undefined
symbol PPC_SERIES. Looking at the rest of the commit, PPC_PSERIES was
probably intended.
Change PPC_SERIES to PPC_PSERIES.
Discovered with the
https://github.com/ulfalizer/Kconfiglib/blob/master/examples/list_undefined.py
script.
Fixes: 76d837a4c0f9 ("KVM: PPC: Book3S PR: Don't include SPAPR TCE code on non-pseries platforms") Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com> Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
cpu_pm_enter() calls the pm notifier chain with CPU_PM_ENTER, then if
there is a failure: CPU_PM_ENTER_FAILED.
When KVM receives CPU_PM_ENTER it calls cpu_hyp_reset() which will
return us to the hyp-stub. If we subsequently get a CPU_PM_ENTER_FAILED,
KVM does nothing, leaving the CPU running with the hyp-stub, at odds
with kvm_arm_hardware_enabled.
Add CPU_PM_ENTER_FAILED as a fallthrough for CPU_PM_EXIT, this reloads
KVM based on kvm_arm_hardware_enabled. This is safe even if CPU_PM_ENTER
never gets as far as KVM, as cpu_hyp_reinit() calls cpu_hyp_reset()
to make sure the hyp-stub is loaded before reloading KVM.
Fixes: 67f691976662 ("arm64: kvm: allows kvm cpu hotplug") CC: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: James Morse <james.morse@arm.com> Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Running with CONFIG_DEBUG_ATOMIC_SLEEP reveals that HV KVM tries to
read guest memory, in order to emulate guest instructions, while
preempt is disabled and a vcore lock is held. This occurs in
kvmppc_handle_exit_hv(), called from post_guest_process(), when
emulating guest doorbell instructions on POWER9 systems, and also
when checking whether we have hit a hypervisor breakpoint.
Reading guest memory can cause a page fault and thus cause the
task to sleep, so we need to avoid reading guest memory while
holding a spinlock or when preempt is disabled.
To fix this, we move the preempt_enable() in kvmppc_run_core() to
before the loop that calls post_guest_process() for each vcore that
has just run, and we drop and re-take the vcore lock around the calls
to kvmppc_emulate_debug_inst() and kvmppc_emulate_doorbell_instr().
Dropping the lock is safe with respect to the iteration over the
runnable vcpus in post_guest_process(); for_each_runnable_thread
is actually safe to use locklessly. It is possible for a vcpu
to become runnable and add itself to the runnable_threads array
(code near the beginning of kvmppc_run_vcpu()) and then get included
in the iteration in post_guest_process despite the fact that it
has not just run. This is benign because vcpu->arch.trap and
vcpu->arch.ceded will be zero.
This fixes a bug where it is possible to enter a guest on a POWER9
system without having the XIVE (interrupt controller) context loaded.
This can happen because we unload the XIVE context from the CPU
before doing the real-mode handling for machine checks. After the
real-mode handler runs, it is possible that we re-enter the guest
via a fast path which does not load the XIVE context.
To fix this, we move the unloading of the XIVE context to come after
the real-mode machine check handler is called.
Fixes: 5af50993850a ("KVM: PPC: Book3S HV: Native usage of the XIVE interrupt controller") Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
kvm_clear_exception_queue() should clear pending exception.
This also includes exceptions which were only marked pending but not
yet injected. This is because exception.pending is used for both L1
and L2 to determine if an exception should be raised to guest.
Note that an exception which is pending but not yet injected will
be raised again once the guest will be resumed.
Consider the following scenario:
1) L0 KVM with ignore_msrs=false.
2) L1 prepare vmcs12 with the following:
a) No intercepts on MSR (MSR_BITMAP exist and is filled with 0).
b) No intercept for #GP.
c) vmx-preemption-timer is configured.
3) L1 enters into L2.
4) L2 reads an unhandled MSR that exists in MSR_BITMAP
(such as 0x1fff).
L2 RDMSR could be handled as described below:
1) L2 exits to L0 on RDMSR and calls handle_rdmsr().
2) handle_rdmsr() calls kvm_inject_gp() which sets
KVM_REQ_EVENT, exception.pending=true and exception.injected=false.
3) vcpu_enter_guest() consumes KVM_REQ_EVENT and calls
inject_pending_event() which calls vmx_check_nested_events()
which sees that exception.pending=true but
nested_vmx_check_exception() returns 0 and therefore does nothing at
this point. However let's assume it later sees vmx-preemption-timer
expired and therefore exits from L2 to L1 by calling
nested_vmx_vmexit().
4) nested_vmx_vmexit() calls prepare_vmcs12()
which calls vmcs12_save_pending_event() but it does nothing as
exception.injected is false. Also prepare_vmcs12() calls
kvm_clear_exception_queue() which does nothing as
exception.injected is already false.
5) We now return from vmx_check_nested_events() with 0 while still
having exception.pending=true!
6) Therefore inject_pending_event() continues
and we inject L2 exception to L1!...
This commit will fix above issue by changing step (4) to
clear exception.pending in kvm_clear_exception_queue().
Fixes: 664f8e26b00c ("KVM: X86: Fix loss of exception which has not yet been injected") Signed-off-by: Liran Alon <liran.alon@oracle.com> Reviewed-by: Nikita Leshenko <nikita.leshchenko@oracle.com> Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com> Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Consider the following scenario:
1. CPU A calls vmx_deliver_nested_posted_interrupt() to send an IPI
to CPU B via virtual posted-interrupt mechanism.
2. CPU B is currently executing L2 guest.
3. vmx_deliver_nested_posted_interrupt() calls
kvm_vcpu_trigger_posted_interrupt() which will note that
vcpu->mode == IN_GUEST_MODE.
4. Assume that before CPU A sends the physical POSTED_INTR_NESTED_VECTOR
IPI, CPU B exits from L2 to L0 during event-delivery
(valid IDT-vectoring-info).
5. CPU A now sends the physical IPI. The IPI is received in host and
it's handler (smp_kvm_posted_intr_nested_ipi()) does nothing.
6. Assume that before CPU A sets pi_pending=true and KVM_REQ_EVENT,
CPU B continues to run in L0 and reach vcpu_enter_guest(). As
KVM_REQ_EVENT is not set yet, vcpu_enter_guest() will continue and resume
L2 guest.
7. At this point, CPU A sets pi_pending=true and KVM_REQ_EVENT but
it's too late! CPU B already entered L2 and KVM_REQ_EVENT will only be
consumed at next L2 entry!
Another scenario to consider:
1. CPU A calls vmx_deliver_nested_posted_interrupt() to send an IPI
to CPU B via virtual posted-interrupt mechanism.
2. Assume that before CPU A calls kvm_vcpu_trigger_posted_interrupt(),
CPU B is at L0 and is about to resume into L2. Further assume that it is
in vcpu_enter_guest() after check for KVM_REQ_EVENT.
3. At this point, CPU A calls kvm_vcpu_trigger_posted_interrupt() which
will note that vcpu->mode != IN_GUEST_MODE. Therefore, do nothing and
return false. Then, will set pi_pending=true and KVM_REQ_EVENT.
4. Now CPU B continue and resumes into L2 guest without processing
the posted-interrupt until next L2 entry!
To fix both issues, we just need to change
vmx_deliver_nested_posted_interrupt() to set pi_pending=true and
KVM_REQ_EVENT before calling kvm_vcpu_trigger_posted_interrupt().
It will fix the first scenario by chaging step (6) to note that
KVM_REQ_EVENT and pi_pending=true and therefore process
nested posted-interrupt.
It will fix the second scenario by two possible ways:
1. If kvm_vcpu_trigger_posted_interrupt() is called while CPU B has changed
vcpu->mode to IN_GUEST_MODE, physical IPI will be sent and will be received
when CPU resumes into L2.
2. If kvm_vcpu_trigger_posted_interrupt() is called while CPU B hasn't yet
changed vcpu->mode to IN_GUEST_MODE, then after CPU B will change
vcpu->mode it will call kvm_request_pending() which will return true and
therefore force another round of vcpu_enter_guest() which will note that
KVM_REQ_EVENT and pi_pending=true and therefore process nested
posted-interrupt.
Fixes: 705699a13994 ("KVM: nVMX: Enable nested posted interrupt processing") Signed-off-by: Liran Alon <liran.alon@oracle.com> Reviewed-by: Nikita Leshenko <nikita.leshchenko@oracle.com> Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
[Add kvm_vcpu_kick to also handle the case where L1 doesn't intercept L2 HLT
and L2 executes HLT instruction. - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
KVM doesn't follow the SMCCC when it comes to unimplemented calls,
and inject an UNDEF instead of returning an error. Since firmware
calls are now used for security mitigation, they are becoming more
common, and the undef is counter productive.
Instead, let's follow the SMCCC which states that -1 must be returned
to the caller when getting an unknown function number.
The SHA-512 multibuffer code keeps track of the number of blocks pending
in each lane. The minimum of these values is used to identify the next
lane that will be completed. Unused lanes are set to a large number
(0xFFFFFFFF) so that they don't affect this calculation.
However, it was forgotten to set the lengths to this value in the
initial state, where all lanes are unused. As a result it was possible
for sha512_mb_mgr_get_comp_job_avx2() to select an unused lane, causing
a NULL pointer dereference. Specifically this could happen in the case
where ->update() was passed fewer than SHA512_BLOCK_SIZE bytes of data,
so it then called sha_complete_job() without having actually submitted
any blocks to the multi-buffer code. This hit a NULL pointer
dereference if another task happened to have submitted blocks
concurrently to the same CPU and the flush timer had not yet expired.
Fix this by initializing sha512_mb_mgr->lens correctly.
As usual, this bug was found by syzkaller.
Fixes: 45691e2d9b18 ("crypto: sha512-mb - submit/flush routines for AVX2") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
If the device is of type VFL_TYPE_SUBDEV then vdev->ioctl_ops
is NULL so the 'if (!ops->vidioc_query_ext_ctrl)' check would crash.
Add a test for !ops to the condition.
All sub-devices that have controls will use the control framework,
so they do not have an equivalent to ops->vidioc_query_ext_ctrl.
Returning false if ops is NULL is the correct thing to do here.
The 32-bit compat v4l2 ioctl handling is implemented based on its 64-bit
equivalent. It converts 32-bit data structures into its 64-bit
equivalents and needs to provide the data to the 64-bit ioctl in user
space memory which is commonly allocated using
compat_alloc_user_space().
However, due to how that function is implemented, it can only be called
a single time for every syscall invocation.
Supposedly to avoid this limitation, the existing code uses a mix of
memory from the kernel stack and memory allocated through
compat_alloc_user_space().
Under normal circumstances, this would not work, because the 64-bit
ioctl expects all pointers to point to user space memory. As a
workaround, set_fs(KERNEL_DS) is called to temporarily disable this
extra safety check and allow kernel pointers. However, this might
introduce a security vulnerability: The result of the 32-bit to 64-bit
conversion is writeable by user space because the output buffer has been
allocated via compat_alloc_user_space(). A malicious user space process
could then manipulate pointers inside this output buffer, and due to the
previous set_fs(KERNEL_DS) call, functions like get_user() or put_user()
no longer prevent kernel memory access.
The new approach is to pre-calculate the total amount of user space
memory that is needed, allocate it using compat_alloc_user_space() and
then divide up the allocated memory to accommodate all data structures
that need to be converted.
An alternative approach would have been to retain the union type karg
that they allocated on the kernel stack in do_video_ioctl(), copy all
data from user space into karg and then back to user space. However, we
decided against this approach because it does not align with other
compat syscall implementations. Instead, we tried to replicate the
get_user/put_user pairs as found in other places in the kernel:
if (get_user(clipcount, &up->clipcount) ||
put_user(clipcount, &kp->clipcount)) return -EFAULT;
Clearly nobody could be bothered to upstream this patch or at minimum
tell us :-( We only heard about this a week ago.
This patch was rebased and cleaned up. Compared to the original I
also swapped the order of the convert_in_user arguments so that they
matched copy_in_user. It was hard to review otherwise. I also replaced
the ALLOC_USER_SPACE/ALLOC_AND_GET by a normal function.
Fixes: 6b5a9492ca ("v4l: introduce string control support.") Signed-off-by: Daniel Mentz <danielmentz@google.com> Co-developed-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Some ioctls need to copy back the result even if the ioctl returned
an error. However, don't do this for the error code -ENOTTY.
It makes no sense in that cases.
There is nothing wrong with using an unknown buffer type. So
stop spamming the kernel log whenever this happens. The kernel
will just return -EINVAL to signal this.
ctrl_is_pointer just hardcoded two known string controls, but that
caused problems when using e.g. custom controls that use a pointer
for the payload.
Reimplement this function: it now finds the v4l2_ctrl (if the driver
uses the control framework) or it calls vidioc_query_ext_ctrl (if the
driver implements that directly).
In both cases it can now check if the control is a pointer control
or not.
Instead of doing sizeof(struct foo) use sizeof(*up). There even were
cases where 4 * sizeof(__u32) was used instead of sizeof(kp->reserved),
which is very dangerous when the size of the reserved array changes.
projects / mirror_ubuntu-bionic-kernel.git / log