Symptom: After vnicc/rx_bcast has been manually set to 0,
bridge_* sysfs parameters can still be set or written.
Only occurs on HiperSockets, as OSA doesn't support changing rx_bcast.
Vnic characteristics and bridgeport settings are mutually exclusive.
rx_bcast defaults to 1, so manually setting it to 0 should disable
bridge_* parameters.
Instead it makes sense here to check the supported mask. If the card
does not support vnicc at all, bridge commands are always allowed.
Fixes: caa1f0b10d18 ("s390/qeth: add VNICC enable/disable support") Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If journal is dirty when mount, it will be replayed but jbd2 sb log tail
cannot be updated to mark a new start because journal->j_flag has
already been set with JBD2_ABORT first in journal_init_common.
When a new transaction is committed, it will be recored in block 1
first(journal->j_tail is set to 1 in journal_reset). If emergency
restart happens again before journal super block is updated
unfortunately, the new recorded trans will not be replayed in the next
mount.
The following steps describe this procedure in detail.
1. mount and touch some files
2. these transactions are committed to journal area but not checkpointed
3. emergency restart
4. mount again and its journals are replayed
5. journal super block's first s_start is 1, but its s_seq is not updated
6. touch a new file and its trans is committed but not checkpointed
7. emergency restart again
8. mount and journal is dirty, but trans committed in 6 will not be
replayed.
This exception happens easily when this lun is used by only one node.
If it is used by multi-nodes, other node will replay its journal and its
journal super block will be updated after recovery like what this patch
does.
ocfs2_recover_node->ocfs2_replay_journal.
The following jbd2 journal can be generated by touching a new file after
journal is replayed, and seq 15 is the first valid commit, but first seq
is 13 in journal super block.
The following is journal recovery log when recovering the upper jbd2
journal when mount again.
syslog:
ocfs2: File system on device (252,1) was not unmounted cleanly, recovering it.
fs/jbd2/recovery.c:(do_one_pass, 449): Starting recovery pass 0
fs/jbd2/recovery.c:(do_one_pass, 449): Starting recovery pass 1
fs/jbd2/recovery.c:(do_one_pass, 449): Starting recovery pass 2
fs/jbd2/recovery.c:(jbd2_journal_recover, 278): JBD2: recovery, exit status 0, recovered transactions 13 to 13
Due to first commit seq 13 recorded in journal super is not consistent
with the value recorded in block 1(seq is 14), journal recovery will be
terminated before seq 15 even though it is an unbroken commit, inode 8257802 is a new file and it will be lost.
Link: http://lkml.kernel.org/r/20191217020140.2197-1-li.kai4@h3c.com Signed-off-by: Kai Li <li.kai4@h3c.com> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Reviewed-by: Changwei Ge <gechangwei@live.cn> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If dma_alloc_coherent() returns NULL in ioat_alloc_ring(), ring
allocation must not proceed.
Until now, if the first call to dma_alloc_coherent() in
ioat_alloc_ring() returned NULL, the processing could proceed, failing
with NULL-pointer dereferencing further down the line.
Signed-off-by: Alexander Barabash <alexander.barabash@dell.com> Acked-by: Dave Jiang <dave.jiang@intel.com> Link: https://lore.kernel.org/r/75e9c0e84c3345d693c606c64f8b9ab5@x13pwhopdag1307.AMER.DELL.COM Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In some cases we seem to submit two transactions in a row, which
causes us to lose track of the first. If we then cancel the
request, we may still get an interrupt, which traverses a null
ds_run value.
So try to avoid starting a new transaction if the ds_run value
is set.
While this patch avoids the null pointer crash, I've had some
reports of the k3dma driver still getting confused, which
suggests the ds_run/ds_done value handling still isn't quite
right. However, I've not run into an issue recently with it
so I think this patch is worth pushing upstream to avoid the
crash.
Signed-off-by: John Stultz <john.stultz@linaro.org>
[add ss tag] Link: https://lore.kernel.org/r/20191218190906.6641-1-john.stultz@linaro.org Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
__sanitizer_cov_trace_pc() is not linked in and causing link
failure if KCOV_INSTRUMENT is enabled. Fix this by disabling
instrumentation for compressed image.
In old kernels, some APIs still try to use parent->of_node from struct gpio_chip,
and it could be resulted in kernel panic because parent is NULL. Adding platform
device to gpiochip->parent can fix this problem.
The driver was reading the wrong register as the 10-hour digit due to
a misplaced ')'. It was in fact reading the 1-second digit register due
to this bug.
Also remove the use of a magic number for the hour mask and use the define
for it which was already present.
Fixes: 4f9b9bba1dd1 ("rtc: Add an RTC driver for the Oki MSM6242") Tested-by: Kars de Jong <jongk@linux-m68k.org> Signed-off-by: Kars de Jong <jongk@linux-m68k.org> Link: https://lore.kernel.org/r/20191116110548.8562-1-jongk@linux-m68k.org Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We expect 64-bit calculation result from below statement, however
in 32-bit machine, looped left shift operation on pgoff_t type
variable may cause overflow issue, fix it by forcing type cast.
page->index << PAGE_SHIFT;
Fixes: 26de9b117130 ("f2fs: avoid unnecessary updating inode during fsync") Fixes: 0a2aa8fbb969 ("f2fs: refactor __exchange_data_block for speed up") Signed-off-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When building with Clang + -Wtautological-pointer-compare:
drivers/net/wireless/realtek/rtlwifi/regd.c:389:33: warning: comparison
of address of 'rtlpriv->regd' equal to a null pointer is always false
[-Wtautological-pointer-compare]
if (wiphy == NULL || &rtlpriv->regd == NULL)
~~~~~~~~~^~~~ ~~~~
1 warning generated.
The address of an array member is never NULL unless it is the first
struct member so remove the unnecessary check. This was addressed in
the staging version of the driver in commit f986978b32b3 ("Staging:
rtlwifi: remove unnecessary NULL check").
While we are here, fix the following checkpatch warning:
CHECK: Comparison to NULL could be written "!wiphy"
35: FILE: drivers/net/wireless/realtek/rtlwifi/regd.c:389:
+ if (wiphy == NULL)
Fixes: 0c8173385e54 ("rtl8192ce: Add new driver")
Link:https://github.com/ClangBuiltLinux/linux/issues/750 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Acked-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The driver does the wrong thing when cs_change is set on a non-last
xfer in a message. When cs_change is set, the driver deactivates the
CS and leaves it off until a later xfer again has cs_change set whereas
it should be briefly toggling CS off and on again.
This patch brings the behaviour of the driver back in line with the
documentation and common sense. The delay of 10 us is the same as is
used by the default spi_transfer_one_message() function in spi.c.
[gregory: rebased on for-5.5 from spi tree] Fixes: 8090d6d1a415 ("spi: atmel: Refactor spi-atmel to use SPI framework queue") Signed-off-by: Mans Rullgard <mans@mansr.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Link: https://lore.kernel.org/r/20191018153504.4249-1-gregory.clement@bootlin.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
spi_nor_read_raw() assigns the result of 'ssize_t spi_nor_read_data()'
to the 'int ret' variable, while 'ssize_t' is a 64-bit type and *int*
is a 32-bit type on the 64-bit machines. This silent truncation isn't
really valid, so fix up the variable's type.
spi_nor_read() assigns the result of 'ssize_t spi_nor_read_data()'
to the 'int ret' variable, while 'ssize_t' is a 64-bit type and *int*
is a 32-bit type on the 64-bit machines. This silent truncation isn't
really valid, so fix up the variable's type.
Fixes: 59451e1233bd ("mtd: spi-nor: change return value of read/write") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
>From isp_video_release(), &isp->video_lock is held and subsequent
vb2_fop_release() tries to lock vdev->lock which is same with the
previous one. Replace vb2_fop_release() with _vb2_fop_release() to
fix the recursive locking.
Fixes: 1380f5754cb0 ("[media] videobuf2: Add missing lock held on vb2_fop_release") Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com> Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit da298c6d98d5 ("[media] v4l2: replace video op g_mbus_fmt by pad
op get_fmt") converted a former ov6650_g_fmt() video operation callback
to an ov6650_get_fmt() pad operation callback. However, the converted
function disregards a format->which flag that pad operations should
obey and always returns active frame format settings.
That can be fixed by always responding to V4L2_SUBDEV_FORMAT_TRY with
-EINVAL, or providing the response from a pad config argument, likely
updated by a former user call to V4L2_SUBDEV_FORMAT_TRY .set_fmt().
Since implementation of the latter is trivial, go for it.
Fixes: da298c6d98d5 ("[media] v4l2: replace video op g_mbus_fmt by pad op get_fmt") Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
User arguments passed to .get/set_fmt() pad operation callbacks may
contain unsupported values. The driver takes control over frame size
and pixel code as well as colorspace and field attributes but has never
cared for remainig format attributes, i.e., ycbcr_enc, quantization
and xfer_func, introduced by commit 11ff030c7365 ("[media]
v4l2-mediabus: improve colorspace support"). Fix it.
Set up a static v4l2_mbus_framefmt structure with attributes
initialized to reasonable defaults and use it for updating content of
user provided arguments. In case of V4L2_SUBDEV_FORMAT_ACTIVE,
postpone frame size update, now performed from inside ov6650_s_fmt()
helper, util the user argument is first updated in ov6650_set_fmt() with
default frame format content. For V4L2_SUBDEV_FORMAT_TRY, don't copy
all attributes to pad config, only those handled by the driver, then
fill the response with the default frame format updated with resulting
pad config format code and frame size.
Since its initial submission, the driver selects V4L2_COLORSPACE_JPEG
for supported formats other than V4L2_MBUS_FMT_SBGGR8_1X8. According
to v4l2-compliance test program, V4L2_COLORSPACE_JPEG applies
exclusively to V4L2_PIX_FMT_JPEG. Since the sensor does not support
JPEG format, fix it to always select V4L2_COLORSPACE_SRGB.
Fixes: 2f6e2404799a ("[media] SoC Camera: add driver for OV6650 sensor") Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Per Documentation/DMA-API-HOWTO.txt,
To unmap a scatterlist, just call:
dma_unmap_sg(dev, sglist, nents, direction);
.. note::
The 'nents' argument to the dma_unmap_sg call must be
the _same_ one you passed into the dma_map_sg call,
it should _NOT_ be the 'count' value _returned_ from the
dma_map_sg call.
However in the driver, priv->nent is directly assigned with value
returned from dma_map_sg, and dma_unmap_sg use priv->nent for unmap,
this breaks the API usage.
So introduce a new entry orig_nent to remember 'nents'.
The dmaengine_prep_slave_sg needs to use sg count returned
by dma_map_sg, not use sport->dma_tx_nents, because the return
value of dma_map_sg is not always same with "nents".
Fixes: b4cdc8f61beb ("serial: imx: add DMA support for imx6q") Signed-off-by: Peng Fan <peng.fan@nxp.com> Link: https://lore.kernel.org/r/1573108875-26530-1-git-send-email-peng.fan@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On PowerNV the PCIe topology is (currently) managed by the powernv platform
code in Linux in cooperation with the platform firmware. Linux's native
PCIe port service drivers operate independently of both and this can cause
problems.
The main issue is that the portbus driver will conflict with the platform
specific hotplug driver (pnv_php) over ownership of the MSI used to notify
the host when a hotplug event occurs. The portbus driver claims this MSI on
behalf of the individual port services because the same interrupt is used
for hotplug events, PMEs (on root ports), and link bandwidth change
notifications. The portbus driver will always claim the interrupt even if
the individual port service drivers, such as pciehp, are compiled out.
The second, bigger, problem is that the hotplug port service driver
fundamentally does not work on PowerNV. The platform assumes that all
PCI devices have a corresponding arch-specific handle derived from the DT
node for the device (pci_dn) and without one the platform will not allow
a PCI device to be enabled. This problem is largely due to historical
baggage, but it can't be resolved without significant re-factoring of the
platform PCI support.
We can fix these problems in the interim by setting the
"pcie_ports_disabled" flag during platform initialisation. The flag
indicates the platform owns the PCIe ports which stops the portbus driver
from being registered.
This does have the side effect of disabling all port services drivers
that is: AER, PME, BW notifications, hotplug, and DPC. However, this is
not a huge disadvantage on PowerNV since these services are either unused
or handled through other means.
Fixes: 66725152fb9f ("PCI/hotplug: PowerPC PowerNV PCI hotplug driver") Signed-off-by: Oliver O'Halloran <oohall@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20191118065553.30362-1-oohall@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The af_unix protocol family has a custom ioctl command (inexplicibly
based on SIOCPROTOPRIVATE), but never had a compat_ioctl handler for
32-bit applications.
Since all commands are compatible here, add a trivial wrapper that
performs the compat_ptr() conversion for SIOCOUTQ/SIOCINQ. SIOCUNIXFILE
does not use the argument, but it doesn't hurt to also use compat_ptr()
here.
Fixes: ba94f3088b79 ("unix: add ioctl to open a unix socket file with O_PATH") Cc: netdev@vger.kernel.org Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In the same way as for msm8974-hammerhead, l21 load, used for SDCARD
VMMC, needs to be increased in order to prevent any voltage drop issues
(due to limited current) happening with some SDCARDS or during specific
operations (e.g. write).
The call to pinctrl_count_index_with_args checks for a -EINVAL return
however this function calls pinctrl_get_list_and_count and this can
return -ENOENT. Rather than check for a specific error, fix this by
checking for any error return to catch the -ENOENT case.
Addresses-Coverity: ("Improper use of negative") Fixes: 003910ebc83b ("pinctrl: Introduce TI IOdelay configuration driver") Signed-off-by: Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20190920122030.14340-1-colin.king@canonical.com Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Save and restore top PLL related configuration registers for big (APLL)
and LITTLE (KPLL) cores during suspend/resume cycle. So far, CPU clocks
were reset to default values after suspend/resume cycle and performance
after system resume was affected when performance governor has been selected.
Fixes: 773424326b51 ("clk: samsung: exynos5420: add more registers to restore list") Signed-off-by: Marian Mihailescu <mihailescu2m@gmail.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This was found only after the whole thing with the inline functions, but
the compiler actually found something. The value of the `bias` (in
adis16480_get_calibbias()) should only be set if the read operation was
successful.
No actual known problem occurs as users of this function all
ultimately check the return value. Hence probably not stable material.
Fixes: 2f3abe6cbb6c9 ("iio:imu: Add support for the ADIS16480 and similar IMUs") Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
I've found that on occasion, "rmmod <dev>" will hang while if an NFS
is under load.
Ensure that ri_remove_done is initialized only just before the
transport is woken up to force a close. This avoids the completion
possibly getting initialized again while the CM event handler is
waiting for a wake-up.
Fixes: bebd031866ca ("xprtrdma: Support unplugging an HCA from under an NFS mount") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Some of ASUS laptops like UX431FL keyboard backlight cannot be set to
brightness 0. According to ASUS' information, the brightness should be
0x80 ~ 0x83. This patch fixes it by following the logic.
Fixes: e9809c0b9670 ("asus-wmi: add keyboard backlight support") Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Reviewed-by: Daniel Drake <drake@endlessm.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If an attached disk with protection information enabled is reformatted
to Type 0 the revalidation code does not clear the original protection
type and subsequent accesses will keep setting RDPROTECT/WRPROTECT.
Set the protection type to 0 if the disk reports PROT_EN=0 in READ
CAPACITY(16).
[mkp: commit desc]
Fixes: fe542396da73 ("[SCSI] sd: Ensure we correctly disable devices with unknown protection type") Link: https://lore.kernel.org/r/1578532344-101668-1-git-send-email-chenxiang66@hisilicon.com Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Doing an add/remove/add on a SCSI device in an enclosure leads to an oops
caused by poisoned values in the enclosure device list pointers. The
reason is because we are keeping the enclosure device across the enclosed
device add/remove/add but the current code is doing a
device_add/device_del/device_add on it. This is the wrong thing to do in
sysfs, so fix it by not doing a device_del on the enclosure device simply
because of a hot remove of the drive in the slot.
[mkp: added missing email addresses]
Fixes: 43d8eb9cfd0a ("[SCSI] ses: add support for enclosure component hot removal") Link: https://lore.kernel.org/r/1578532892.3852.10.camel@HansenPartnership.com Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Reported-by: Luo Jiaxing <luojiaxing@huawei.com> Tested-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The code added by this patch is similar to the code that already exists in
ibmvscsis_determine_resid(). This patch has been tested by running the
following command:
This is similar to 942491c9e6d6 ("xfs: fix AIM7 regression"). Apparently
our current rwsem code doesn't like doing the trylock, then lock for
real scheme. This causes extra contention on the lock and can be
measured eg. by AIM7 benchmark. So change our read/write methods to
just do the trylock for the RWF_NOWAIT case.
../fs/cifs/smb2file.c:70:3: warning: misleading indentation; statement
is not part of the previous 'if' [-Wmisleading-indentation]
if (oparms->tcon->use_resilient) {
^
../fs/cifs/smb2file.c:66:2: note: previous statement is here
if (rc)
^
1 warning generated.
This warning occurs because there is a space after the tab on this line.
Remove it so that the indentation is consistent with the Linux kernel
coding style and clang no longer warns.
Fixes: 592fafe644bf ("Add resilienthandles mount parm") Link: https://github.com/ClangBuiltLinux/linux/issues/826 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The supervision frame is L2 frame.
When supervision frame is created, hsr module doesn't set network header.
If tap routine is enabled, dev_queue_xmit_nit() is called and it checks
network_header. If network_header pointer wasn't set(or invalid),
it resets network_header and warns.
In order to avoid unnecessary warning message, resetting network_header
is needed.
Test commands:
ip netns add nst
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link set veth1 netns nst
ip link set veth3 netns nst
ip link set veth0 up
ip link set veth2 up
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip netns exec nst ip link set veth1 up
ip netns exec nst ip link set veth3 up
ip netns exec nst ip link add hsr1 type hsr slave1 veth1 slave2 veth3
ip netns exec nst ip a a 192.168.100.2/24 dev hsr1
ip netns exec nst ip link set hsr1 up
tcpdump -nei veth0
Splat looks like:
[ 175.852292][ C3] protocol 88fb is buggy, dev veth0
Fixes: f421436a591d ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When a GPIO offset in a lookup table is out-of-range, the printed error
message (1) does not include the actual out-of-range value, and (2)
contains an off-by-one error in the upper bound.
Avoid user confusion by also printing the actual GPIO offset, and
correcting the upper bound of the range.
While at it, use "%u" for unsigned int.
Sample impact:
-requested GPIO 0 is out of range [0..32] for chip e6052000.gpio
+requested GPIO 0 (45) is out of range [0..31] for chip e6052000.gpio
This patch writes the inverse value of Interrupt Mask Status
register into the Interrupt Enable register in
zynq_gpio_restore_context API to fix the bug.
Fixes: e11de4de28c0 ("gpio: zynq: Add support for suspend resume") Signed-off-by: Swapna Manupati <swapna.manupati@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com> Link: https://lore.kernel.org/r/1577362338-28744-2-git-send-email-srinivas.neeli@xilinx.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In current spdifrx driver locks may be requested as follows:
- request lock on iec capture control, when starting synchronization.
- request lock in interrupt context, when spdifrx stop is called
from IRQ handler.
Take lock with IRQs disabled, to avoid the possible deadlock.
Some adapters need a fence Work Entry to handle retransmission. Currently
the driver checks for this condition, only if the Send queue entry is
signalled. Implement the condition check, irrespective of the signalled
state of the Work queue entries
Failure to add the fence can result in access to memory that is already
marked as completed, triggering data corruption, transmission failure,
IOMMU failures, etc.
Fixes: 9152e0b722b2 ("RDMA/bnxt_re: HW workarounds for handling specific conditions") Link: https://lore.kernel.org/r/1574671174-5064-3-git-send-email-selvin.xavier@broadcom.com Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Alarm registers high byte was reserved for other functions.
This add mask in alarm registers operation functions.
This also fix error condition in interrupt handler.
Fixes: fc2979118f3f ("rtc: mediatek: Add MT6397 RTC driver") Signed-off-by: Ran Bi <ran.bi@mediatek.com> Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com> Link: https://lore.kernel.org/r/1576057435-3561-6-git-send-email-hsin-hsiung.wang@mediatek.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In the implementation of i2400m_op_rfkill_sw_toggle() the allocated
buffer for cmd should be released before returning. The
documentation for i2400m_msg_to_dev() says when it returns the buffer
can be reused. Meaning cmd should be released in either case. Move
kfree(cmd) before return to be reached by all execution paths.
Fixes: 2507e6ab7a9a ("wimax: i2400: fix memory leak") Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In i2400m_op_rfkill_sw_toggle cmd buffer should be released along with
skb response.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
SyzKaller hit the null pointer deref while reading from uninitialized
udev->product in zr364xx_vidioc_querycap().
==================================================================
BUG: KASAN: null-ptr-deref in read_word_at_a_time+0xe/0x20
include/linux/compiler.h:274
Read of size 1 at addr 0000000000000000 by task v4l_id/5287
Commit 15122ee2c515 ("arm64: Enforce BBM for huge IO/VMAP mappings")
disallowed block mappings for ioremap since that code does not honor
break-before-make. The same APIs are also used for permission updating
though and the extra checks prevent the permission updates from happening,
even though this should be permitted. This results in read-only permissions
not being fully applied. Visibly, this can occasionaly be seen as a failure
on the built in rodata test when the test data ends up in a section or
as an odd RW gap on the page table dump. Fix this by using
pgattr_change_is_safe instead of p*d_present for determining if the
change is permitted.
Reviewed-by: Kees Cook <keescook@chromium.org> Tested-by: Peter Robinson <pbrobinson@gmail.com> Reported-by: Peter Robinson <pbrobinson@gmail.com> Fixes: 15122ee2c515 ("arm64: Enforce BBM for huge IO/VMAP mappings") Signed-off-by: Laura Abbott <labbott@redhat.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
ioremap_page_range doesn't honour break-before-make and attempts to put
down huge mappings (using p*d_set_huge) over the top of pre-existing
table entries. This leads to us leaking page table memory and also gives
rise to TLB conflicts and spurious aborts, which have been seen in
practice on Cortex-A75.
Until this has been resolved, refuse to put block mappings when the
existing entry is found to be present.
Fixes: 324420bf91f60 ("arm64: add support for ioremap() block mappings") Reported-by: Hanjun Guo <hanjun.guo@linaro.org> Reported-by: Lei Li <lious.lilei@hisilicon.com> Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Ben Hutchings [Tue, 14 Jan 2020 15:44:11 +0000 (15:44 +0000)]
arm64: mm: Change page table pointer name in p[md]_set_huge()
BugLink: https://bugs.launchpad.net/bugs/1861934
This is preparation for the following backported fixes. It was done
upstream as part of commit 20a004e7b017 "arm64: mm: Use
READ_ONCE/WRITE_ONCE when accessing page tables", the rest of which
does not seem suitable for stable.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Instead of open coding the generation of page table entries, use the
macros/functions that exist for this - pfn_p*d and p*d_populate. Most
code in the kernel already uses these macros, this patch tries to fix
up the few places that don't. This is useful for the next patch in this
series, which needs to change the page table entry logic, and it's
better to have that logic in one place.
The KVM extended ID map is special, since we're creating a level above
CONFIG_PGTABLE_LEVELS and the required function isn't available. Leave
it as is and add a comment to explain it. (The normal kernel ID map code
doesn't need this change because its page tables are created in assembly
(__create_page_tables)).
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com> Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com> Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Tested-by: Bob Picco <bob.picco@oracle.com> Reviewed-by: Bob Picco <bob.picco@oracle.com> Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The select() implementation is carefully tuned to put a sensible amount
of data on the stack for holding a copy of the user space fd_set, but
not too large to risk overflowing the kernel stack.
When building a 32-bit kernel with clang, we need a little more space
than with gcc, which often triggers a warning:
fs/select.c:619:5: error: stack frame size of 1048 bytes in function 'core_sys_select' [-Werror,-Wframe-larger-than=]
int core_sys_select(int n, fd_set __user *inp, fd_set __user *outp,
I experimentally found that for 32-bit ARM, reducing the maximum stack
usage by 64 bytes keeps us reliably under the warning limit again.
Link: http://lkml.kernel.org/r/20190307090146.1874906-1-arnd@arndb.de Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Andi Kleen <ak@linux.intel.com> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Christoph Hellwig <hch@lst.de> Cc: Eric Dumazet <edumazet@google.com> Cc: "Darrick J. Wong" <darrick.wong@oracle.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Miles Chen <miles.chen@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
clang inlines the dev_ethtool() more aggressively than gcc does, leading
to a larger amount of used stack space:
net/core/ethtool.c:2536:24: error: stack frame size of 1216 bytes in function 'dev_ethtool' [-Werror,-Wframe-larger-than=]
Marking the sub-functions that require the most stack space as
noinline_for_stack gives us reasonable behavior on all compilers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Miles Chen <miles.chen@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
hidraw and uhid device nodes are always available for writing so we should
always report EPOLLOUT and EPOLLWRNORM bits, not only in the cases when
there is nothing to read.
When polling a connected /dev/hidrawX device, it is useful to get the
EPOLLOUT when writing is possible. Since writing is possible as soon as
the device is connected, always return it.
Right now EPOLLOUT is only returned when there are also input reports
are available. This works if devices start sending reports when
connected, but some HID devices might need an output report first before
sending any input reports. This change will allow using EPOLLOUT here as
well.
Always return EPOLLOUT from hidraw_poll when a device is connected.
This is safe since writes are always possible (but will always block).
hidraw does not support non-blocking writes and instead always calls
blocking backend functions on write requests. Hence, so far, a call to
poll never returned EPOLLOUT, which confuses tools like socat.
Serdev sub-system claims all ACPI serial devices that are not already
initialised. As a result, no device node is created for serial ports
on certain boards such as the Apollo Lake based UP2. This has the
unintended consequence of not being able to raise the login prompt via
serial connection.
Introduce a blacklist to reject ACPI serial devices that should not be
claimed by serdev sub-system. Add the peripheral ids for Intel HS UART
to the blacklist to bring back serial port on SoCs carrying them.
Cc: stable@vger.kernel.org Signed-off-by: Punit Agrawal <punit1.agrawal@toshiba.co.jp> Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Johan Hovold <johan@kernel.org> Cc: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20191219100345.911093-1-punit1.agrawal@toshiba.co.jp Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Discussion in the below link reported that symbols in modules can appear
to be before _stext on ARM architecture, causing wrapping with the
offsets of this tracepoint. Change the offset type to s32 to fix this.
Link: http://lore.kernel.org/r/20191127154428.191095-1-antonio.borneo@st.com Link: http://lkml.kernel.org/r/20200102194625.226436-1-joel@joelfernandes.org Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: David Sterba <dsterba@suse.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Mike Rapoport <rppt@linux.ibm.com> Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com> Cc: Sakari Ailus <sakari.ailus@linux.intel.com> Cc: Antonio Borneo <antonio.borneo@st.com> Cc: stable@vger.kernel.org Fixes: d59158162e032 ("tracing: Add support for preempt and irq enable/disable events") Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Add quirk to ALC285_FIXUP_SPEAKER2_TO_DAC1, which is the same fixup
applied for X1 Carbon 7th gen in commit d2cd795c4ece ("ALSA: hda -
fixup for the bass speaker on Lenovo Carbon X1 7th gen").
Signed-off-by: Kailang Yang <kailang@realtek.com> Reviewed-by: Jaroslav Kysela <perex@perex.cz> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We must let the USB host idle things properly before we switch to debug
UART mode. Otherwise the USB host may never idle after disconnecting
devices, and that causes the next enumeration to be flakey.
Cc: Jacopo Mondi <jacopo@jmondi.org> Cc: Marcel Partap <mpartap@gmx.net> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Michael Scott <hashcode0f@gmail.com> Cc: NeKit <nekit1000@gmail.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: Sebastian Reichel <sre@kernel.org> Acked-by: Pavel Machek <pavel@ucw.cz> Fixes: 6d6ce40f63af ("phy: cpcap-usb: Add CPCAP PMIC USB support") Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If musb_mailbox() returns an error, we must still continue to finish
configuring the phy.
Otherwise the phy state may end up only half initialized, and this can
cause the debug serial console to stop working. And this will happen if the
usb driver musb controller is not loaded.
Let's fix the issue by adding helper for cpcap_usb_try_musb_mailbox().
Fixes: 6d6ce40f63af ("phy: cpcap-usb: Add CPCAP PMIC USB support") Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Cc: Sebastian Reichel <sre@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
It turns out that even though endpoints with a maxpacket length of 0
aren't useful for data transfer, the descriptors do serve other
purposes. In particular, skipping them will also skip over other
class-specific descriptors for classes such as UVC. This unexpected
side effect has caused some UVC cameras to stop working.
In addition, the USB spec requires that when isochronous endpoint
descriptors are present in an interface's altsetting 0 (which is true
on some devices), the maxpacket size _must_ be set to 0. Warning
about such things seems like a bad idea.
This patch updates an earlier commit which would log a warning and
skip these endpoint descriptors. Now we only log a warning, and we
don't even do that for isochronous endpoints in altsetting 0.
We don't need to worry about preventing endpoints with maxpacket = 0
from ever being used for data transfers; usb_submit_urb() already
checks for this.
Reported-and-tested-by: Roger Whittaker <Roger.Whittaker@suse.com> Fixes: d482c7bb0541 ("USB: Skip endpoints with 0 maxpacket length") Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://marc.info/?l=linux-usb&m=157790377329882&w=2 Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2001061040270.1514-100000@iolanthe.rowland.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The open method of hiddev handler fails to bring the device out of
autosuspend state as was promised in 0361a28d3f9a, as it actually has 2
blocks that try to start the transport (call hid_hw_open()) with both
being guarded by the "open" counter, so the 2nd block is never executed as
the first block increments the counter so it is never at 0 when we check
it for the second block.
Additionally hiddev_open() was leaving counter incremented on errors,
causing the device to never be reopened properly if there was ever an
error.
Let's fix all of this by factoring out code that creates client structure
and powers up the device into a separate function that is being called
from usbhid_open() with the "existancelock" being held.
Fixes: 0361a28d3f9a ("HID: autosuspend support for USB HID") Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
An allnoconfig build complains about unused symbols due to functions
that are called via conditional cpufeature and cpu_errata table entries.
Annotate these as __maybe_unused if they are likely to be generic, or
predicate their compilation on the same option as the table entry if
they are specific to a given alternative.
Signed-off-by: Will Deacon <will.deacon@arm.com>
[Just a portion of the original patch] Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If the serial device is disconnected and reconnected, it re-enumerates
properly but does not link it. fwiw, linking means just saving the port
index, so allow it always as there is no harm in saving the same value
again even if it tries to relink with the same port.
Fixes: fb2b90014d78 ("tty: link tty and port before configuring it as console") Reported-by: Kenneth R. Crudup <kenny@panix.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191227174434.12057-1-sudipm.mukherjee@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There seems to be a race condition in tty drivers and I could see on
many boot cycles a NULL pointer dereference as tty_init_dev() tries to
do 'tty->port->itty = tty' even though tty->port is NULL.
'tty->port' will be set by the driver and if the driver has not yet done
it before we open the tty device we can get to this situation. By adding
some extra debug prints, I noticed that:
uart_add_one_port() registers the console, as soon as it registers, the
userspace tries to use it and that leads to tty_open() but
uart_add_one_port() has not yet done tty_port_link_device() and so
tty->port is not yet configured when control reaches tty_init_dev().
Further look into the code and tty_port_link_device() is done by
uart_add_one_port(). After registering the console uart_add_one_port()
will call tty_port_register_device_attr_serdev() and
tty_port_link_device() is called from this.
Call add tty_port_link_device() before uart_configure_port() is done and
add a check in tty_port_link_device() so that it only links the port if
it has not been done yet.
[Why]
According to DP spec, it should shift left 4 digits for NO_STOP_BIT
in REMOTE_I2C_READ message. Not 5 digits.
In current code, NO_STOP_BIT is always set to zero which means I2C
master is always generating a I2C stop at the end of each I2C write
transaction while handling REMOTE_I2C_READ sideband message. This issue
might have the generated I2C signal not meeting the requirement. Take
random read in I2C for instance, I2C master should generate a repeat
start to start to read data after writing the read address. This issue
will cause the I2C master to generate a stop-start rather than a
re-start which is not expected in I2C random read.
[How]
Correct the shifting value of NO_STOP_BIT for DP_REMOTE_I2C_READ case in
drm_dp_encode_sideband_req().
Changes since v1:(https://patchwork.kernel.org/patch/11312667/)
* Add more descriptions in commit and cc to stable
Fixes: ad7f8a1f9ced ("drm/helper: add Displayport multi-stream helper (v0.6)") Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Wayne Lin <Wayne.Lin@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200103055001.10287-1-Wayne.Lin@amd.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When userspace requests a video mode parameter value that is not
supported, frame buffer device drivers should round it up to a supported
value, if possible, instead of just rejecting it. This allows
applications to quickly scan for supported video modes.
Currently this rule is not followed for the number of bits per pixel,
causing e.g. "fbset -depth N" to fail, if N is smaller than the current
number of bits per pixel.
Fix this by returning an error only if bits per pixel is too large, and
setting it to the current value otherwise.
See also Documentation/fb/framebuffer.rst, Section 2 (Programmer's View
of /dev/fb*").
Fixes: 865afb11949e5bf4 ("drm/fb-helper: reject any changes to the fbdev") Cc: stable@vger.kernel.org Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20191230132734.4538-1-geert+renesas@glider.be Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If we happen to have a garbage in input device's keycode table with values
too big we'll end up doing clear_bit() with offset way outside of our
bitmaps, damaging other objects within an input device or even outside of
it. Let's add sanity checks to the returned old keycodes.
We should not be leaving half-mapped usages with potentially invalid
keycodes, as that may confuse hidinput_find_key() when the key is located
by index, which may end up feeding way too large keycode into the VT
keyboard handler and cause OOB write there:
BUG: KASAN: global-out-of-bounds in clear_bit include/asm-generic/bitops-instrumented.h:56 [inline]
BUG: KASAN: global-out-of-bounds in kbd_keycode drivers/tty/vt/keyboard.c:1411 [inline]
BUG: KASAN: global-out-of-bounds in kbd_event+0xe6b/0x3790 drivers/tty/vt/keyboard.c:1495
Write of size 8 at addr ffffffff89a1b2d8 by task syz-executor108/1722
...
kbd_keycode drivers/tty/vt/keyboard.c:1411 [inline]
kbd_event+0xe6b/0x3790 drivers/tty/vt/keyboard.c:1495
input_to_handler+0x3b6/0x4c0 drivers/input/input.c:118
input_pass_values.part.0+0x2e3/0x720 drivers/input/input.c:145
input_pass_values drivers/input/input.c:949 [inline]
input_set_keycode+0x290/0x320 drivers/input/input.c:954
evdev_handle_set_keycode_v2+0xc4/0x120 drivers/input/evdev.c:882
evdev_do_ioctl drivers/input/evdev.c:1150 [inline]
The Advantech PCI-1713 has 32 analog input channels, but an incorrect
bit-mask in the definition of the `PCI171X_MUX_CHANH(x)` and
PCI171X_MUX_CHANL(x)` macros is causing channels 16 to 31 to be aliases
of channels 0 to 15. Change the bit-mask value from 0xf to 0xff to fix
it. Note that the channel numbers will have been range checked already,
so the bit-mask isn't really needed.
The pullup may be already enabled before the driver is initialized. This
happens for instance on JZ4740.
It has to be disabled at init time, as we cannot guarantee that a gadget
driver will be bound to the UDC.
Signed-off-by: Paul Cercueil <paul@crapouillou.net> Suggested-by: Bin Liu <b-liu@ti.com> Cc: stable@vger.kernel.org Signed-off-by: Bin Liu <b-liu@ti.com> Link: https://lore.kernel.org/r/20200107152625.857-3-b-liu@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When disconnected as USB B-device, suspend interrupt should come before
diconnect interrupt, because the DP/DM pins are shorter than the
VBUS/GND pins on the USB connectors. But we sometimes get a suspend
interrupt after disconnect interrupt. In that case we have devctl set to
99 with VBUS still valid and musb_pm_runtime_check_session() wrongly
thinks we have an active session. We have no other interrupts after
disconnect coming in this case at least with the omap2430 glue.
Let's fix the issue by checking the interrupt status again with
delayed work for the devctl 99 case. In the suspend after disconnect
case the devctl session bit has cleared by then and musb can idle.
For a typical USB B-device connect case we just continue with normal
interrupts.
Fixes: 467d5c980709 ("usb: musb: Implement session bit based runtime PM for musb-core") Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Cc: Sebastian Reichel <sre@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Bin Liu <b-liu@ti.com> Link: https://lore.kernel.org/r/20200107152625.857-2-b-liu@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On some laptops enabling wakeup on the GPIO interrupts used for ACPI _AEI
event handling causes spurious wakeups.
This commit adds a new honor_wakeup option, defaulting to true (our current
behavior), which can be used to disable wakeup on troublesome hardware
to avoid these spurious wakeups.
This is a workaround for an architectural problem with s2idle under Linux
where we do not have any mechanism to immediately go back to sleep after
wakeup events, other then for embedded-controller events using the standard
ACPI EC interface, for details see:
https://lore.kernel.org/linux-acpi/61450f9b-cbc6-0c09-8b3a-aff6bf9a0b3c@redhat.com/
One series of laptops which is not able to suspend without this workaround
is the HP x2 10 Cherry Trail models, this commit adds a DMI based quirk
which makes sets honor_wakeup to false on these models.
Cc: stable@vger.kernel.org Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20200105160357.97154-3-hdegoede@redhat.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
KMSAN sysbot detected a read access to an untinitialized value in the
headroom of an outgoing CAN related sk_buff. When using CAN sockets this
area is filled appropriately - but when using a packet socket this
initialization is missing.
The problematic read access occurs in the CAN receive path which can
only be triggered when the sk_buff is sent through a (virtual) CAN
interface. So we check in the sending path whether we need to perform
the missing initializations.
Fixes: d3b58c47d330d ("can: replace timestamp as unique skb attribute") Reported-by: syzbot+b02ff0707a97e4e79ebb@syzkaller.appspotmail.com Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> Cc: linux-stable <stable@vger.kernel.org> # >= v4.1 Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Under load, the RX side of the mscan driver can get stuck while TX still
works. Restarting the interface locks up the system. This behaviour
could be reproduced reliably on a MPC5121e based system.
The patch fixes the return value of the NAPI polling function (should be
the number of processed packets, not constant 1) and the condition under
which IRQs are enabled again after polling is finished.
With this patch, no more lockups were observed over a test period of ten
days.
Fixes: afa17a500a36 ("net/can: add driver for mscan family & mpc52xx_mscan") Signed-off-by: Florian Faber <faber@faberman.de> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Make sure to always use the descriptors of the current alternate setting
to avoid future issues when accessing fields that may differ between
settings.
Signed-off-by: Johan Hovold <johan@kernel.org> Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices") Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>