Phil Elwell [Mon, 20 Jun 2016 12:51:44 +0000 (13:51 +0100)]
vchiq_arm: Avoid use of mutex in add_completion
Claiming the completion_mutex within add_completion did prevent some
messages appearing twice, but provokes a deadlock caused by vcsm using
vchiq within a page fault handler.
Revert the use of completion_mutex, and instead fix the original
problem using more memory barriers.
Phil Elwell [Thu, 21 Apr 2016 12:49:32 +0000 (13:49 +0100)]
vchiq_arm: Add completion records under the mutex
An issue was observed when flushing openmax components
which generate a large number of messages returning
buffers to host.
We occasionally found a duplicate message from 16
messages prior, resulting in a buffer returned twice.
While only one thread adds completions, without the
mutex you don't get the protection of the automatic
memory barrier you get with synchronisation objects.
Phil Elwell [Wed, 23 Mar 2016 20:53:47 +0000 (20:53 +0000)]
vchiq_arm: Service callbacks must not fail
Service callbacks are not allowed to return an error. The internal callback
that delivers events and messages to user tasks does not enqueue them if
the service is closing, but this is not an error and should not be
reported as such.
Michael Zoran [Wed, 24 Aug 2016 10:35:56 +0000 (03:35 -0700)]
Add arm64 configuration and device tree differences.
Disable MMC_BCM2835_SDHOST and MMC_BCM2835 since these drivers are crashing at the moment.
ARM64: Modify default config to get raspbian to boot (#1686)
1. Enable emulation of deprecated instructions.
2. Enable ARM 8.1 and 8.2 features which are not detected at runtime.
3. Switch the default governer to powersave.
4. Include the watchdog timer driver in the kernel image rather then a module.
Cheong2K [Fri, 26 Feb 2016 10:20:10 +0000 (18:20 +0800)]
brcm: adds support for BCM43341 wifi
brcmfmac: Disable power management
Disable wireless power saving in the brcmfmac WLAN driver. This is a
temporary measure until the connectivity loss resulting from power
saving is resolved.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: Use original country code as a fallback
brcmfmac: Configure country code using device specific settings
prevents region codes from working on devices that lack a region code
translation table. In the event of an absent table, preserve the old
behaviour of using the provided code as-is.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: Plug memory leak in brcmf_fill_bss_param
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: do not use internal roaming engine by default
Some evidence of curing disconnects with this disabled, so make it a default.
Can be overridden with module parameter roamoff=0
See: http://projectable.me/optimize-my-pi-wi-fi/
brcmfmac: Change stop_ap sequence
Patch from Broadcom/Cypress to resolve a customer error
This is a port of Pantelis Antoniou's v3 port that makes use of the
new upstreamed configfs support for binary attributes.
Original commit message:
Add a runtime interface to using configfs for generic device tree overlay
usage. With it its possible to use device tree overlays without having
to use a per-platform overlay manager.
Please see Documentation/devicetree/configfs-overlays.txt for more info.
Changes since v2:
- Removed ifdef CONFIG_OF_OVERLAY (since for now it's required)
- Created a documentation entry
- Slight rewording in Kconfig
Changes since v1:
- of_resolve() -> of_resolve_phandles().
Originally-signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com> Signed-off-by: Phil Elwell <phil@raspberrypi.org>
DT configfs: Fix build errors on other platforms
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
DT configfs: fix build error
There is an error when compiling rpi-4.6.y branch:
CC drivers/of/configfs.o
drivers/of/configfs.c:291:21: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
.default_groups = of_cfs_def_groups,
^
drivers/of/configfs.c:291:21: note: (near initialization for 'of_cfs_subsys.su_group.default_groups.next')
Phil Elwell [Tue, 23 Feb 2016 17:26:48 +0000 (17:26 +0000)]
amba_pl011: Don't use DT aliases for numbering
The pl011 driver looks for DT aliases of the form "serial<n>",
and if found uses <n> as the device ID. This can cause
/dev/ttyAMA0 to become /dev/ttyAMA1, which is confusing if the
other serial port is provided by the 8250 driver which doesn't
use the same logic.
P33M [Wed, 21 Oct 2015 13:55:21 +0000 (14:55 +0100)]
rpi_display: add backlight driver and overlay
Add a mailbox-driven backlight controller for the Raspberry Pi DSI
touchscreen display. Requires updated GPU firmware to recognise the
mailbox request.
Signed-off-by: Gordon Hollingworth <gordon@raspberrypi.org>
Allo Piano DAC boards: Initial 2 channel (stereo) support (#1645)
Add initial 2 channel (stereo) support for Allo Piano DAC (2.0/2.1) boards,
using allo-piano-dac-pcm512x-audio overlay and allo-piano-dac ALSA ASoC
machine driver.
NB. The initial support is 2 channel (stereo) ONLY!
(The Piano DAC 2.1 will only support 2 channel (stereo) left/right output,
pending an update to the upstream pcm512x codec driver, which will have
to be submitted via upstream. With the initial downstream support,
provided by this patch, the Piano DAC 2.1 subwoofer outputs will
not function.)
Matt Flax [Mon, 16 May 2016 11:36:31 +0000 (21:36 +1000)]
New AudioInjector.net Pi soundcard with low jitter audio in and out.
Contains the sound/soc/bcm ALSA machine driver and necessary alterations to the Kconfig and Makefile.
Adds the dts overlay and updates the Makefile and README.
Updates the relevant defconfig files to enable building for the Raspberry Pi.
Thanks to Phil Elwell (pelwell) for the review, simple-card concepts and discussion. Thanks to Clive Messer for overlay naming suggestions.
Added support for headphones, microphone and bclk_ratio settings.
This patch adds headphone and microphone capability to the Audio Injector sound card. The patch also sets the bit clock ratio for use in the bcm2835-i2s driver. The bcm2835-i2s can't handle an 8 kHz sample rate when the bit clock is at 12 MHz because its register is only 10 bits wide which can't represent the ch2 offset of 1508. For that reason, the rate constraint is added.
ARM: adau1977-adc: Add basic machine driver for adau1977 codec driver.
This commit adds basic support for the codec usage including: Device tree overlay,
binding I2S bus and setting I2S mode, clock source and frequency setting according
to spec.
Forward port of 3.10.x driver from https://github.com/koalo
We are using a custom board and would like to use rpi 3.18.x
kernel. Patch works fine for our embedded system.
URL to the audio chip:
http://www.mikroe.com/add-on-boards/audio-voice/audio-codec-proto/
Added driver for HiFiBerry Amp amplifier add-on board
The driver contains a low-level hardware driver for the TAS5713 and the
drivers for the Raspberry Pi I2S subsystem.
TAS5713: return error if initialisation fails
Existing TAS5713 driver logs errors during initialisation, but does not return
an error code. Therefore even if initialisation fails, the driver will still be
loaded, but won't work. This patch fixes this. I2C communication error will now
reported correctly by a non-zero return code.
HiFiBerry Amp: fix device-tree problems
Some code to load the driver based on device-tree-overlays was missing. This is added by this patch.
The driver is based on the HiFiBerry DAC driver. However HiFiBerry DAC+ uses
a different codec chip (PCM5122), therefore a new driver is necessary.
Add support for the HiFiBerry DAC+ Pro.
The HiFiBerry DAC+ and DAC+ Pro products both use the existing bcm sound driver with the DAC+ Pro having a special clock device driver representing the two high precision oscillators.
An addition bug fix is included for the PCM512x codec where by the physical size of the sample frame is used in the calculation of the LRCK divisor as it was found to be wrong when using 24-bit depth sample contained in a little endian 4-byte sample frame.
Limit PCM512x "Digital" gain to 0dB by default with HiFiBerry DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Add dt param to force HiFiBerry DAC+ Pro into slave mode
"dtoverlay=hifiberry-dacplus,slave"
Add 'slave' param to use HiFiBerry DAC+ Pro in slave mode,
with Pi as master for bit and frame clock.
Gordon Garrity [Sat, 8 Mar 2014 16:56:57 +0000 (16:56 +0000)]
Add IQaudIO Sound Card support for Raspberry Pi
Set a limit of 0dB on Digital Volume Control
The main volume control in the PCM512x DAC has a range up to
+24dB. This is dangerously loud and can potentially cause massive
clipping in the output stages. Therefore this sets a sensible
limit of 0dB for this control.
Allow up to 24dB digital gain to be applied when using IQAudIO DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Modify IQAudIO DAC+ ASoC driver to set card/dai config from dt
Add the ability to set the card name, dai name and dai stream name, from
dt config.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
IQaudIO: auto-mute for AMP+ and DigiAMP+
IQAudIO amplifier mute via GPIO22. Add dt params for "one-shot" unmute
and auto mute.
Revision 2, auto mute implementing HiassofT suggestion to mute/unmute
using set_bias_level, rather than startup/shutdown....
"By default DAPM waits 5 seconds (pmdown_time) before shutting down
playback streams so a close/stop immediately followed by open/start
doesn't trigger an amp mute+unmute."
Tested on both AMP+ (via DAC+) and DigiAMP+, with both options...
dtoverlay=iqaudio-dacplus,unmute_amp
"one-shot" unmute when kernel module loads.
dtoverlay=iqaudio-dacplus,auto_mute_amp
Unmute amp when ALSA device opened by a client. Mute, with 5 second delay
when ALSA device closed. (Re-opening the device within the 5 second close
window, will cancel mute.)
Revision 4, using gpiod.
Revision 5, clean-up formatting before adding mute code.
- Convert tab plus 4 space formatting to 2x tab
- Remove '// NOT USED' commented code
Revision 6, don't attempt to "one-shot" unmute amp, unless card is
successfully registered.
Daniel Matuschek [Wed, 15 Jan 2014 20:42:08 +0000 (21:42 +0100)]
ASoC: BCM:Add support for HiFiBerry Digi. Driver is based on the patched WM8804 driver.
Signed-off-by: Daniel Matuschek <daniel@matuschek.net>
Add a parameter to turn off SPDIF output if no audio is playing
This patch adds the paramater auto_shutdown_output to the kernel module.
Default behaviour of the module is the same, but when auto_shutdown_output
is set to 1, the SPDIF oputput will shutdown if no stream is playing.
bugfix for 32kHz sample rate, was missing
HiFiBerry Digi: set SPDIF status bits for sample rate
The HiFiBerry Digi driver did not signal the sample rate in the SPDIF status bits.
While this is optional, some DACs and receivers do not accept this signal. This patch
adds the sample rate bits in the SPDIF status block.
Added HiFiBerry Digi+ Pro driver
Signed-off-by: Daniel Matuschek <daniel@hifiberry.com>
Daniel Matuschek [Wed, 15 Jan 2014 20:41:23 +0000 (21:41 +0100)]
ASoC: wm8804: Implement MCLK configuration options, add 32bit support WM8804 can run with PLL frequencies of 256xfs and 128xfs for most sample rates. At 192kHz only 128xfs is supported. The existing driver selects 128xfs automatically for some lower samples rates. By using an additional mclk_div divider, it is now possible to control the behaviour. This allows using 256xfs PLL frequency on all sample rates up to 96kHz. It should allow lower jitter and better signal quality. The behavior has to be controlled by the sound card driver, because some sample frequency share the same setting. e.g. 192kHz and 96kHz use 24.576MHz master clock. The only difference is the MCLK divider.
This also added support for 32bit data.
Signed-off-by: Daniel Matuschek <daniel@matuschek.net>
Phil Elwell [Thu, 25 Jun 2015 11:16:11 +0000 (12:16 +0100)]
gpio-poweroff: Allow it to work on Raspberry Pi
The Raspberry Pi firmware manages the power-down and reboot
process. To do this it installs a pm_power_off handler, causing
the gpio-poweroff module to abort the probe function.
This patch introduces a "force" DT property that overrides that
behaviour, and also adds a DT overlay to enable and control it.
Note that running in an active-low configuration (DT parameter
"active_low") requires a custom dt-blob.bin and probably won't
allow a reboot without switching off, so an external inversion
of the trigger signal may be preferable.
Harm Hanemaaijer [Thu, 20 Jun 2013 18:21:39 +0000 (20:21 +0200)]
Speed up console framebuffer imageblit function
Especially on platforms with a slower CPU but a relatively high
framebuffer fill bandwidth, like current ARM devices, the existing
console monochrome imageblit function used to draw console text is
suboptimal for common pixel depths such as 16bpp and 32bpp. The existing
code is quite general and can deal with several pixel depths. By creating
special case functions for 16bpp and 32bpp, by far the most common pixel
formats used on modern systems, a significant speed-up is attained
which can be readily felt on ARM-based devices like the Raspberry Pi
and the Allwinner platform, but should help any platform using the
fb layer.
The special case functions allow constant folding, eliminating a number
of instructions including divide operations, and allow the use of an
unrolled loop, eliminating instructions with a variable shift size,
reducing source memory access instructions, and eliminating excessive
branching. These unrolled loops also allow much better code optimization
by the C compiler. The code that selects which optimized variant is used
is also simplified, eliminating integer divide instructions.
The speed-up, measured by timing 'cat file.txt' in the console, varies
between 40% and 70%, when testing on the Raspberry Pi and Allwinner
ARM-based platforms, depending on font size and the pixel depth, with
the greater benefit for 32bpp.
Phil Elwell [Fri, 6 Feb 2015 13:50:57 +0000 (13:50 +0000)]
BCM270x_DT: Add pwr_led, and the required "input" trigger
The "input" trigger makes the associated GPIO an input. This is to support
the Raspberry Pi PWR LED, which is driven by external hardware in normal use.
N.B. pwr_led is not available on Model A or B boards.
leds-gpio: Implement the brightness_get method
The power LED uses some clever logic that means it is driven
by a voltage measuring circuit when configured as input, otherwise
it is driven by the GPIO output value. This patch wires up the
brightness_get method for leds-gpio so that user-space can monitor
the LED value via /sys/class/gpio/led1/brightness. Using the input
trigger this returns an indication of the system power health,
otherwise it is just whatever value the trigger has written most
recently.
Change DT node named 'axi' to 'soc' so it matches ARCH_BCM2835.
The VC4 bootloader fills in certain properties in the 'axi' subtree,
but since this is part of an upstreaming effort, the name is changed.
Signed-off-by: Noralf Tronnes notro@tronnes.org
BCM2708_DT: Correct length of the peripheral space
Use dts-dirs feature for overlays.
The kernel makefiles have a dts-dirs target that is for vendor subdirectories.
Using this fixes the install_dtbs target, which previously did not install the overlays.
BCM270X_DT: configure I2S DMA channels
Signed-off-by: Matthias Reichl <hias@horus.com>
BCM270X_DT: switch to bcm2835-i2s
I2S soundcard drivers with proper devicetree support (i.e. not linking
to the cpu_dai/platform via name but to cpu/platform via of_node)
will work out of the box without any modifications.
When the kernel is compiled without devicetree support the platform
code will instantiate the bcm2708-i2s driver and I2S soundcard drivers
will link to it via name, as before.
Add paramter to toggle sdio-device-polling
done every second or once at boot-time.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
BCM270X_DT: Make mmc overlay compatible with current firmware
The original DT overlay logic followed a merge-then-patch procedure,
i.e. parameters are applied to the loaded overlay before the overlay
is merged into the base DTB. This sequence has been changed to
patch-then-merge, in order to support parameterised node names, and
to protect against bad overlays. As a result, overrides (parameters)
must only target labels in the overlay, but the overlay can obviously target nodes in the base DTB.
mmc-overlay.dts (that switches back to the original mmc sdcard
driver) is the only overlay violating that rule, and this patch
fixes it.
bcm270x_dt: Use the sdhost MMC controller by default
The "mmc" overlay reverts to using the other controller.
squash: Add cprman to dt
BCM270X_DT: Use clk_core for I2C interfaces
BCM270X_DT: Use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi
The mainline Device Tree files are quite close to downstream now.
Let's use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi as base files
for our dts files.
bcm270x.dtsi contains the downstream bcm283x.dtsi diff.
bcm2708-rpi.dtsi is the downstream version of bcm2835-rpi.dtsi.
Other changes:
- The led node has moved from /soc/leds to /leds. This is not a problem
since the label is used to reference it.
- The clk_osc reg property changes from 6 to 3.
- The gpu nodes has their interrupt property set in the base file.
- the clocks label does not point to the /clocks node anymore, but
points to the cprman node. This is not a problem since the overlays
that use the clock node refer to it directly: target-path = "/clocks";
- some nodes now have 2 labels since mainline and downstream differs in
this respect: cprman/clocks, spi0/spi, gpu/vc4.
- some nodes doesn't have an explicit status = "okay" since they're not
disabled in the base file: watchdog and random.
- gpiomem doesn't need an explicit status = "okay".
- bcm2708-rpi-cm.dts got the hpd-gpios property from bcm2708_common.dtsi,
it's now set directly in that file.
- bcm2709-rpi-2-b.dts has the timer node moved from /soc/timer to /timer.
- Removed clock-frequency property on the bcm{2709,2710}.dtsi timer nodes.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Use raspberrypi-power to turn on USB power
Use the raspberrypi-power driver to turn on USB power.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Add a .dtbo target, use for overlays
Change the filenames and extensions to keep the pre-DDT style of
overlay (<name>-overlay.dtb) distinct from new ones that use a
different style of local fixups (<name>.dtbo), and to match other
platforms.
The RPi firmware uses the DDTK trailer atom to choose which type of
overlay to use for each kernel.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Don't generate "linux,phandle" props
The EPAPR standard says to use "phandle" properties to store phandles,
rather than the deprecated "linux,phandle" version. By default, dtc
generates both, but adding "-H epapr" causes it to only generate
"phandle"s, saving some space and clutter.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add overlay for enc28j60 on SPI2
Works on SPI2 for compute module
BCM270X_DT: Add midi-uart0 overlay
MIDI requires 31.25kbaud, a baudrate unsupported by Linux. The
midi-uart0 overlay configures uart0 (ttyAMA0) to use a fake clock
so that requesting 38.4kbaud actually gets 31.25kbaud.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add i2c-sensor overlay
The i2c-sensor overlay is a container for various pressure and
temperature sensors, currently bmp085 and bmp280. The standalone
bmp085_i2c-sensor overlay is now deprecated.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: overlays/*-overlay.dtb -> overlays/*.dtbo (#1752)
We now create overlays as .dtbo files.
build: support for .dtbo files for dtb overlays
Kernel 4.4.6+ on RaspberryPi support .dtbo files for overlays, instead of .dtb.
Patch the kernel, which has faulty rules to generate .dtbo the way yocto does
Phil Elwell [Mon, 11 May 2015 08:00:42 +0000 (09:00 +0100)]
scripts: Add mkknlimg and knlinfo scripts from tools repo
The Raspberry Pi firmware looks for a trailer on the kernel image to
determine whether it was compiled with Device Tree support enabled.
If the firmware finds a kernel without this trailer, or which has a
trailer indicating that it isn't DT-capable, it disables DT support
and reverts to using ATAGs.
The mkknlimg utility adds that trailer, having first analysed the
image to look for signs of DT support and the kernel version string.
knlinfo displays the contents of the trailer in the given kernel image.
scripts/mkknlimg: Add support for ARCH_BCM2835
Add a new trailer field indicating whether this is an ARCH_BCM2835
build, as opposed to MACH_BCM2708/9. If the loader finds this flag
is set it changes the default base dtb file name from bcm270x...
to bcm283y...
Also update knlinfo to show the status of the field.
scripts/mkknlimg: Improve ARCH_BCM2835 detection
The board support code contains sufficient strings to be able to
distinguish 2708 vs. 2835 builds, so remove the check for
bcm2835-pm-wdt which could exist in either.
Also, since the canned configuration is no longer built in (it's
a module), remove the config string checking.
scripts: Multi-platform support for mkknlimg and knlinfo
The firmware uses tags in the kernel trailer to choose which dtb file
to load. Current firmware loads bcm2835-*.dtb if the '283x' tag is true,
otherwise it loads bcm270*.dtb. This scheme breaks if an image supports
multiple platforms.
This patch adds '270X' and '283X' tags to indicate support for RPi and
upstream platforms, respectively. '283x' (note lower case 'x') is left
for old firmware, and is only set if the image only supports upstream
builds.
scripts/mkknlimg: Append a trailer for all input
Now that the firmware assumes an unsigned kernel is DT-capable, it is
helpful to be able to mark a kernel as being non-DT-capable.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
scripts/knlinfo: Decode DDTK atom
Show the DDTK atom as being a boolean.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mkknlimg: Retain downstream-kernel detection
With the death of ARCH_BCM2708 and ARCH_BCM2709, a new way is needed to
determine if this is a "downstream" build that wants the firmware to
load a bcm27xx .dtb. The vc_cma driver is used downstream but not
upstream, making vc_cma_init a suitable predicate symbol.
Vincent Sanders [Wed, 30 Jan 2013 12:45:18 +0000 (12:45 +0000)]
bcm2835: add v4l2 camera device
- Supports raw YUV capture, preview, JPEG and H264.
- Uses videobuf2 for data transfer, using dma_buf.
- Uses 3.6.10 timestamping
- Camera power based on use
- Uses immutable input mode on video encoder
Signed-off-by: Daniel Stone <daniels@collabora.com> Signed-off-by: Luke Diamand <luked@broadcom.com>
V4L2: Fixes from 6by9
V4L2: Fix EV values. Add manual shutter speed control
V4L2 EV values should be in units of 1/1000. Corrected.
Add support for V4L2_CID_EXPOSURE_ABSOLUTE which should
give manual shutter control. Requires manual exposure mode
to be selected first.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Correct JPEG Q-factor range
Should be 1-100, not 0-100
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix issue of driver jamming if STREAMON failed.
Fix issue where the driver was left in a partially enabled
state if STREAMON failed, and would then reject many IOCTLs
as it thought it was streaming.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix ISO controls.
Driver was passing the index to the GPU, and not the desired
ISO value.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add flicker avoidance controls
Add support for V4L2_CID_POWER_LINE_FREQUENCY to set flicker
avoidance frequencies.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add support for frame rate control.
Add support for frame rate (or time per frame as V4L2
inverts it) control via s_parm.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Improve G_FBUF handling so we pass conformance
Return some sane numbers for get framebuffer so that
we pass conformance.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix information advertised through g_vidfmt
Width and height were being stored based on incorrect
values.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add support for inline H264 headers
Add support for V4L2_CID_MPEG_VIDEO_REPEAT_SEQ_HEADER
to control H264 inline headers.
Requires firmware fix to work correctly, otherwise format
has to be set to H264 before this parameter is set.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix JPEG timestamp issue
JPEG images were coming through from the GPU with timestamp
of 0. Detect this and give current system time instead
of some invalid value.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix issue when switching down JPEG resolution.
JPEG buffer size calculation is based on input resolution.
Input resolution was being configured after output port
format. Caused failures if switching from one JPEG resolution
to a smaller one.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Enable MJPEG encoding
Requires GPU firmware update to support MJPEG encoder.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Correct flag settings for compressed formats
Set flags field correctly on enum_fmt_vid_cap for compressed
image formats.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: H264 profile & level ctrls, FPS control and auto exp pri
Several control handling updates.
H264 profile and level controls.
Timeperframe/FPS reworked to add V4L2_CID_EXPOSURE_AUTO_PRIORITY to
select whether AE is allowed to override the framerate specified.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Correct BGR24 to RGB24 in format table
Adds the other flavours of YUYV, and NV12.
Corrects the overlay advertised colourspace.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Drop logging msg from info to debug
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Initial pass at scene modes.
Only supports exposure mode and metering modes.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add manual white balance control.
Adds support for V4L2_CID_RED_BALANCE and
V4L2_CID_BLUE_BALANCE. Only has an effect if
V4L2_CID_AUTO_N_PRESET_WHITE_BALANCE has
V4L2_WHITE_BALANCE_MANUAL selected.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
config: Enable V4L / MMAL driver
V4L2: Increase the MMAL timeout to 3sec
MJPEG codec flush is now taking longer and results
in a kernel panic if the driver has stopped waiting for
the result when it finally completes.
Increase the timeout value from 1 to 3secs.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add support for setting H264_I_PERIOD
Adds support for the parameter V4L2_CID_MPEG_VIDEO_H264_I_PERIOD
to set the frequency with which I frames are produced.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Enable GPU function for removing padding from images.
GPU can now support arbitrary strides, although may require
additional processing to achieve it. Enable this feature
so that the images delivered are the size requested.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add support for V4L2_PIX_FMT_BGR32
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Set the colourspace to avoid odd YUV-RGB conversions
Removes the amiguity from the conversion routines and stops
them dropping back to the SD vs HD choice of coeffs.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Make video/still threshold a run-time param
Move the define for at what resolution the driver
switches from a video mode capture to a stills mode
capture to module parameters.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Fix incorrect pool sizing
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add option to disable enum_framesizes.
Gstreamer's handling of a driver that advertises
V4L2_FRMSIZE_TYPE_STEPWISE to define the supported
resolutions is broken. See bug
https://bugzilla.gnome.org/show_bug.cgi?id=726521
Optional parameter of gst_v4l2src_is_broken added.
If non-zero, the driver claims not to support that
ioctl, and gstreamer should be happy again (it
guesses a set of defaults for itself).
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Add support for more image formats
Adds YVU420 (YV12), YVU420SP (NV21), and BGR888.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
V4L2: Extend range for V4L2_CID_MPEG_VIDEO_H264_I_PERIOD
Request to extend the range from the fairly arbitrary
1000 frames (33 seconds at 30fps). Extend out to the
max range supported (int32 value).
Also allow 0, which is handled by the codec as only
send an I-frame on the first frame and never again.
There may be an exception if it detects a significant
scene change, but there's no easy way around that.
Signed-off-by: Dave Stevenson <dsteve@broadcom.com>
bcm2835-camera: stop_streaming now has a void return
BCM2835-V4L2: Fix compliance test failures
VIDIOC_TRY_FMT and VIDIOC_S_FMT tests were faling due
to reporting V4L2_COLORSPACE_JPEG when the colour
format wasn't V4L2_PIX_FMT_JPEG.
Now reports V4L2_COLORSPACE_SMPTE170M for YUV formats.
bcm2835 camera planar/packed stride length
Added a field to the mmal_fmt struct used to compute the bytes per line
when using a particular format. This results in the correct stride being
calculated even when the format is planar.
Signed-off-by: Garrett Wilson <g@floft.net>
bcm2835: camera: check for scene not being found
static analysis by cppcheck detected some potential NULL pointer
dereference issues:
[drivers/media/platform/bcm2835/controls.c:854]: (error) Possible null
pointer dereference: scene
(and lines 858, 859 too)
it is possible that scene is not found because of an invalue ctrl->val
and is therefore NULL and hence causing a null pointer dereference.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
bcm2835: memcpy port data to m rather than rmsg
static analysis by cppcheck detected a memcpy to rmsg which is
not actually initialized at that point. The memcpy should be copying
to variable m instead.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
BCM2835-V4L2: Return buffers to videobuf2 on shutdown
https://github.com/raspberrypi/linux/issues/817
Fixes the kernel warning from videobuf2 as buffers
are now returned as they are being flushed on
stop_streaming.
squash: Fixup bcm2835-camera for changes in kernel 4.4 api
v4l2: Fix up driver to upstream timestamp changes
bcm2835-camera: fix a bug in computation of frame timestamp
Fixes #1318
V4L2 driver updates (#1393)
* BCM2835-V4L2: Correct ISO control and add V4L2_CID_ISO_SENSITIVITY_AUTO
https://github.com/raspberrypi/linux/issues/1251
V4L2_CID_ISO_SENSITIVITY was not advertising ISO*1000 as it should.
V4L2_CID_ISO_SENSITIVITY_AUTO was not implemented, so was taking
V4L2_CID_ISO_SENSITIVITY as 0 for auto mode.
Still accepts 0 for auto, but also abides by the new parameter.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
* BCM2835-V4L2: Add a video_nr parameter.
Adds a kernel parameter "video_nr" to specify the preferred
/dev/videoX device node.
https://www.raspberrypi.org/forums/viewtopic.php?f=38&t=136120&p=905545
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
* BCM2835-V4L2: Add support for multiple cameras
Ask GPU on load how many cameras have been detected, and
enumerate that number of devices.
Only applicable on the Compute Module as no other device
exposes multiple CSI2 interfaces.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
* BCM2835-V4L2: Add control of the overlay location and alpha.
Actually do something useful in vidioc_s_fmt_vid_overlay and
vidioc_try_fmt_vid_overlay, rather than effectively having
read-only fields.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
* BCM2835-V4L2: V4L2-Compliance failure fix
VIDIOC_TRY_FMT was failing due to bytesperline not
being set correctly by default.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
* BCM2835-V4L2: Make all module parameters static
Clean up to correct variable scope
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
V4L2: Request maximum resolution from GPU
Get resolution information about the sensors from the GPU
and advertise it correctly.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
BCM2835-V4L2: Increase minimum resolution to 32x32
https://github.com/raspberrypi/linux/issues/1498 showed
up that 16x16 is failing to work on the GPU for some reason.
GPU bug being tracked on
https://github.com/raspberrypi/firmware/issues/607
Workaround here by increasing minimum resolution via V4L2
to 32x32.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
[media]: bcm2835-camera: fix compilation error
There is an error when compiling rpi-4.6.y branch:
CC [M] drivers/media/platform/bcm2835/bcm2835-camera.o
drivers/media/platform/bcm2835/bcm2835-camera.c:639:17: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
.queue_setup = queue_setup,
^
drivers/media/platform/bcm2835/bcm2835-camera.c:639:17: note: (near initialization for 'bm2835_mmal_video_qops.queue_setup')
BCM2835-V4L2: Correct handling for BGR24 vs RGB24.
There was a bug in the GPU firmware that had reversed these
two formats.
Detect the old firmware, and reverse the formats if necessary.
Signed-off-by: Dave Stevenson <6by9@users.noreply.github.com>
BCM2835-v4l2: Fix a conformance test failure
Format ioctls:
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK
warn: v4l2-test-formats.cpp(1195): S_PARM is supported but
doesn't report V4L2_CAP_TIMEPERFRAME.
fail: v4l2-test-formats.cpp(1118): node->has_frmintervals
&& !cap->capability
popcornmix [Wed, 17 Jun 2015 14:44:08 +0000 (15:44 +0100)]
Add Chris Boot's i2c driver
i2c-bcm2708: fixed baudrate
Fixed issue where the wrong CDIV value was set for baudrates below 3815 Hz (for 250MHz bus clock).
In that case the computed CDIV value was more than 0xffff. However the CDIV register width is only 16 bits.
This resulted in incorrect setting of CDIV and higher baudrate than intended.
Example: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0x1704 -> 42430Hz
After correction: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0xffff -> 3815Hz
The correct baudrate is shown in the log after the cdiv > 0xffff correction.
Perform I2C combined transactions when possible
Perform I2C combined transactions whenever possible, within the
restrictions of the Broadcomm Serial Controller.
Disable DONE interrupt during TA poll
Prevent interrupt from being triggered if poll is missed and transfer
starts and finishes.
i2c: Make combined transactions optional and disabled by default
i2c: bcm2708: add device tree support
Add DT support to driver and add to .dtsi file.
Setup pins in .dts file.
i2c is disabled by default.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
bcm2708: don't register i2c controllers when using DT
The devices for the i2c controllers are in the Device Tree.
Only register devices when not using DT.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
I2C: Only register the I2C device for the current board revision
i2c_bcm2708: Fix clock reference counting
Fix grabbing lock from atomic context in i2c driver
2 main changes:
- check for timeouts in the bcm2708_bsc_setup function as indicated by this comment:
/* poll for transfer start bit (should only take 1-20 polls) */
This implies that the setup function can now fail so account for this everywhere it's called
- Removed the clk_get_rate call from inside the setup function as it locks a mutex and that's not ok since we call it from under a spin lock.
i2c-bcm2708: When using DT, leave the GPIO setup to pinctrl
i2c-bcm2708: Increase timeouts to allow larger transfers
Use the timeout value provided by the I2C_TIMEOUT ioctl when waiting
for completion. The default timeout is 1 second.
The third I2C bus (I2C2) is normally reserved for HDMI use. Careless
use of this bus can break an attached display - use with caution.
It is recommended to disable accesses by VideoCore by setting
hdmi_ignore_edid=1 or hdmi_edid_file=1 in config.txt.
The interface is disabled by default - enable using the
i2c2_iknowwhatimdoing DT parameter.
bcm2708-spi: Don't use static pin configuration with DT
Also remove superfluous error checking - the SPI framework ensures the
validity of the chip_select value.
i2c-bcm2708: Remove non-DT support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Set the BSC_CLKT clock streching timeout to 35ms as per SMBus specs.
Fixes i2c_bcm2708: Write to FIFO correctly - v2 (#1574)
* i2c: fix i2c_bcm2708: Clear FIFO before sending data
Make sure FIFO gets cleared before trying to send
data in case of a repeated start (COMBINED=Y).
* i2c: fix i2c_bcm2708: Only write to FIFO when not full
Check if FIFO can accept data before writing.
To avoid a peripheral read on the last iteration of a loop,
both bcm2708_bsc_fifo_fill and ~drain are changed as well.
Aron Szabo [Sat, 16 Jun 2012 10:15:55 +0000 (12:15 +0200)]
lirc: added support for RaspberryPi GPIO
lirc_rpi: Use read_current_timer to determine transmitter delay. Thanks to jjmz and others
See: https://github.com/raspberrypi/linux/issues/525
lirc: Remove restriction on gpio pins that can be used with lirc
Compute Module, for example could use different pins
lirc_rpi: Add parameter to specify input pin pull
Depending on the connected IR circuitry it might be desirable to change the
gpios internal pull from it pull-down default behaviour. Add a module
parameter to allow the user to set it explicitly.
Signed-off-by: Julian Scheel <julian@jusst.de>
lirc-rpi: Use the higher-level irq control functions
This module used to access the irq_chip methods of the
gpio controller directly, rather than going through the
standard enable_irq/irq_set_irq_type functions. This
caused problems on pinctrl-bcm2835 which only implements
the irq_enable/disable methods and not irq_unmask/mask.
lirc-rpi: Correct the interrupt usage
1) Correct the use of enable_irq (i.e. don't call it so often)
2) Correct the shutdown sequence.
3) Avoid a bcm2708_gpio driver quirk by setting the irq flags earlier
lirc-rpi: use getnstimeofday instead of read_current_timer
read_current_timer isn't guaranteed to return values in
microseconds, and indeed it doesn't on a Pi2.
Issue: linux#827
lirc-rpi: Add device tree support, and a suitable overlay
The overlay supports DT parameters that match the old module
parameters, except that gpio_in_pull should be set using the
strings "up", "down" or "off".
lirc-rpi: Also support pinctrl-bcm2835 in non-DT mode
fix auto-sense in lirc_rpi driver
On a Raspberry Pi 2, the lirc_rpi driver might receive spurious
interrupts and change it's low-active / high-active setting.
When this happens, the IR remote control stops working.
This patch disables this auto-detection if the 'sense' parameter
was set in the device tree, making the driver robust to such
spurious interrupts.
Tim Gover [Tue, 22 Jul 2014 14:41:04 +0000 (15:41 +0100)]
vcsm: VideoCore shared memory service for BCM2835
Add experimental support for the VideoCore shared memory service.
This allows user processes to allocate memory from VideoCore's
GPU relocatable heap and mmap the buffers. Additionally, the memory
handles can passed to other VideoCore services such as MMAL, OpenMax
and DispmanX
TODO
* This driver was originally released for BCM28155 which has a different
cache architecture to BCM2835. Consequently, in this release only
uncached mappings are supported. However, there's no fundamental
reason which cached mappings cannot be support or BCM2835
* More refactoring is required to remove the typedefs.
* Re-enable the some of the commented out debug-fs statistics which were
disabled when migrating code from proc-fs.
* There's a lot of code to support sharing of VCSM in order to support
Android. This could probably done more cleanly or perhaps just
removed.
Signed-off-by: Tim Gover <timgover@gmail.com>
config: Disable VC_SM for now to fix hang with cutdown kernel
vcsm: Use boolean as it cannot be built as module
On building the bcm_vc_sm as a module we get the following error:
v7_dma_flush_range and do_munmap are undefined in vc-sm.ko.
popcornmix [Mon, 26 Mar 2012 21:15:50 +0000 (22:15 +0100)]
bcm2708: alsa sound driver
Signed-off-by: popcornmix <popcornmix@gmail.com>
alsa: add mmap support and some cleanups to bcm2835 ALSA driver
snd-bcm2835: Add support for spdif/hdmi passthrough
This adds a dedicated subdevice which can be used for passthrough of non-audio
formats (ie encoded a52) through the hdmi audio link. In addition to this
driver extension an appropriate card config is required to make alsa-lib
support the AES parameters for this device.
snd-bcm2708: Add mutex, improve logging
Fix for ALSA driver crash
Avoids an issue when closing and opening vchiq where a message can arrive before service handle has been written
alsa: reduce severity of expected warning message
snd-bcm2708: Fix dmesg spam for non-error case
alsa: Ensure mutexes are released through error paths
alsa: Make interrupted close paths quieter
BCM270x: Add onboard sound device to Device Tree
Add Device Tree support to alsa driver.
Add device to Device Tree.
Don't add platform devices when booting in DT mode.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835: access controls under the audio mutex
I don't think the ALSA framework provides any kind of automatic
synchronization within the control callbacks. We most likely need
to ensure this manually, so add locking around all access to shared
mutable data. In particular, bcm2835_audio_set_ctls() should
probably always be called under our own audio lock.
snd-bcm2835: Don't allow responses from VC to be interrupted by user signals
There should always be a response, and retry after a signal interruption is not handled, so don't report
we are interruptible.
Phil Elwell [Wed, 11 May 2016 11:50:33 +0000 (12:50 +0100)]
mmc: Add MMC_QUIRK_ERASE_BROKEN for some cards
Some SD cards have been found that corrupt data when small blocks
are erased. Add a quirk to indicate that ERASE should not be used,
and set it for cards of that type.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: Apply QUIRK_BROKEN_ERASE to other capacities
Use mmc_block.card_quirks to override the quirks for all SD or MMC
cards. The value is a bitfield using the bit positions defined in
include/linux/mmc/card.h. If the module parameter is placed in the
kernel command line (or bootargs) stored on the card then, assuming the
device only has one SD card interface, the override effectively becomes
card-specific.
Phil Elwell [Wed, 25 Mar 2015 17:49:47 +0000 (17:49 +0000)]
Adding bcm2835-sdhost driver, and an overlay to enable it
BCM2835 has two SD card interfaces. This driver uses the other one.
bcm2835-sdhost: Error handling fix, and code clarification
bcm2835-sdhost: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the sdhost interface is restricted to integer divisions of
core_freq, and the highest sensible option for a core_freq of 250MHz
is 84 (250/3 = 83.3MHz), the next being 125 (250/2) which is much too
high.
Use at your own risk.
bcm2835-sdhost: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
bcm2835-sdhost: Improve error handling and recovery
1) Expose the hw_reset method to the MMC framework, removing many
internal calls by the driver.
2) Reduce overclock setting on error.
3) Increase timeout to cope with high capacity cards.
4) Add properties and parameters to control pio_limit and debug.
5) Reduce messages at probe time.
bcm2835-sdhost: Further improve overclock back-off
It seems that the sdhost interface returns CRC7 errors for CMD1,
which is the MMC-specific SEND_OP_COND. Returning these errors to
the MMC layer causes a downward spiral, but ignoring them seems
to be harmless.
The bcm2835-mmc driver (and -sdhost driver that copied from it)
contains code to handle SDIO interrupts in a threaded interrupt
handler rather than waking the MMC framework thread. The change
follows a patch from Russell King that adds the facility as the
preferred way of working.
However, the new code path is only present in ARCH_BCM2835
builds, which I have taken to be a way of testing the waters
rather than making the change across the board; I can't see
any technical reason why it wouldn't be enabled for MACH_BCM270X
builds. So this patch standardises on the ARCH_BCM2835 code,
removing the old code paths.
The MMC card-discovery process generates timeouts. This is
expected behaviour, so reporting it to the user serves no purpose.
Suppress the reporting of timeout errors unless the debug flag
is on.
bcm2835-sdhost: Add workaround for odd behaviour on some cards
For reasons not understood, the sdhost driver fails when reading
sectors very near the end of some SD cards. The problem could
be related to the similar issue that reading the final sector
of any card as part of a multiple read never completes, and the
workaround is an extension of the mechanism introduced to solve
that problem which ensures those sectors are always read singly.
bcm2835-sdhost: Major revision
This is a significant revision of the bcm2835-sdhost driver. It
improves on the original in a number of ways:
1) Through the use of CMD23 for reads it appears to avoid problems
reading some sectors on certain high speed cards.
2) Better atomicity to prevent crashes.
3) Higher performance.
4) Activity logging included, for easier diagnosis in the event
of a problem.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Restore ATOMIC flag to PIO sg mapping
Allocation problems have been seen in a wireless driver, and
this is the only change which might have been responsible.
SQUASH: bcm2835-sdhost: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-sdhost driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Workaround for "slow" sectors
Some cards have been seen to cause timeouts after certain sectors are
read. This workaround enforces a minimum delay between the stop after
reading one of those sectors and a subsequent data command.
Using CMD23 (SET_BLOCK_COUNT) avoids this problem, so good cards will
not be penalised by this workaround.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Firmware manages the clock divisor
The bcm2835-sdhost driver hands control of the CDIV clock divisor
register to matching firmware, allowing it to adjust to a changing
core clock. This removes the need to use the performance governor or
to enable io_is_busy on the on-demand governor in order to get the
best SD performance.
N.B. As SD clocks must be an integer divisor of the core clock, it is
possible that the SD clock for "turbo" mode can be different (even
lower) than "normal" mode.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Reset the clock in task context
Since reprogramming the clock can now involve a round-trip to the
firmware it must not be done at atomic context, and a tasklet
is not a task.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Don't exit cmd wait loop on error
The FAIL flag can be set in the CMD register before command processing
is complete, leading to spurious "failed to complete" errors. This has
the effect of promoting harmless CRC7 errors during CMD1 processing
into errors that can delay and even prevent booting.
Also:
1) Convert the last KERN_ERROR message in the register dumping to
KERN_INFO.
2) Remove an unnecessary reset call from bcm2835_sdhost_add_host.
gellert [Fri, 15 Aug 2014 15:35:06 +0000 (16:35 +0100)]
MMC: added alternative MMC driver
mmc: Disable CMD23 transfers on all cards
Pending wire-level investigation of these types of transfers
and associated errors on bcm2835-mmc, disable for now. Fallback of
CMD18/CMD25 transfers will be used automatically by the MMC layer.
Probe error handling is broken in several places.
Simplify error handling by using device managed functions.
Replace pr_{err,info} with dev_{err,info}.
bcm2835-mmc: Add range of debug options for slowing things down
bcm2835-mmc: Add option to disable some delays
bcm2835-mmc: Add option to disable MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Default to disabling MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the mmc interface is restricted to EVEN integer divisions of
250MHz, and the highest sensible option is 63 (250/4 = 62.5), the
next being 125 (250/2) which is much too high.
Use at your own risk.
bcm2835-mmc: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
mmc: bcm2835-mmc: Make available on ARCH_BCM2835
Make the bcm2835-mmc driver available for use on ARCH_BCM2835.
bcm2835-mmc: Don't override bus width capabilities from devicetree
Take out the force setting of the MMC_CAP_4_BIT_DATA host capability
so that the result read from devicetree via mmc_of_parse() is
preserved.
bcm2835-mmc: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-mmc driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
Florian Meier [Fri, 22 Nov 2013 13:22:53 +0000 (14:22 +0100)]
dmaengine: Add support for BCM2708
Add support for DMA controller of BCM2708 as used in the Raspberry Pi.
Currently it only supports cyclic DMA.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
dmaengine: expand functionality by supporting scatter/gather transfers sdhci-bcm2708 and dma.c: fix for LITE channels
DMA: fix cyclic LITE length overflow bug
dmaengine: bcm2708: Remove chancnt affectations
Mirror bcm2835-dma.c commit 9eba5536a7434c69d8c185d4bd1c70734d92287d:
chancnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: overwrite dreq only if it is not set
dreq is set when the DMA channel is fetched from Device Tree.
slave_id is set using dmaengine_slave_config().
Only overwrite dreq with slave_id if it is not set.
dreq/slave_id in the cyclic DMA case is not touched, because I don't
have hardware to test with.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: do device registration in the board file
Don't register the device in the driver. Do it in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: don't restrict DT support to ARCH_BCM2835
Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
Add Device Tree support to the non ARCH_BCM2835 case.
Use the same driver name regardless of architecture.
Add Device Tree entry for bcm2835-dma.
The entry doesn't contain any resources since they are handled
by the arch/arm/mach-bcm270x/dma.c driver.
In non-DT mode, don't add the device in the board file.
BCM270x: Add memory and irq resources to dmaengine device and DT
Prepare for merging of the legacy DMA API arch driver dma.c
with bcm2708-dmaengine by adding memory and irq resources both
to platform file device and Device Tree node.
Don't use BCM_DMAMAN_DRIVER_NAME so we don't have to include mach/dma.h
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Merge with arch dma.c driver and disable dma.c
Merge the legacy DMA API driver with bcm2708-dmaengine.
This is done so we can use bcm2708_fb on ARCH_BCM2835 (mailbox
driver is also needed).
Changes to the dma.c code:
- Use BIT() macro.
- Cutdown some comments to one line.
- Add mutex to vc_dmaman and use this, since the dev lock is locked
during probing of the engine part.
- Add global g_dmaman variable since drvdata is used by the engine part.
- Restructure for readability:
vc_dmaman_chan_alloc()
vc_dmaman_chan_free()
bcm_dma_chan_free()
- Restructure bcm_dma_chan_alloc() to simplify error handling.
- Use device irq resources instead of hardcoded bcm_dma_irqs table.
- Remove dev_dmaman_register() and code it directly.
- Remove dev_dmaman_deregister() and code it directly.
- Simplify bcm_dmaman_probe() using devm_* functions.
- Get dmachans from DT if available.
- Keep 'dma.dmachans' module argument name for backwards compatibility.
Make it available on ARCH_BCM2835 as well.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: set residue_granularity field
bcm2708-dmaengine supports residue reporting at burst level
but didn't report this via the residue_granularity field.
Without this field set properly we get playback issues with I2S cards.
dmaengine: bcm2708-dmaengine: Fix memory leak when stopping a running transfer
bcm2708-dmaengine: Use more DMA channels (but not 12)
1) Only the bcm2708_fb drivers uses the legacy DMA API, and
it requires a BULK-capable channel, so all other types
(FAST, NORMAL and LITE) can be made available to the regular
DMA API.
2) DMA channels 11-14 share an interrupt. The driver can't
handle this, so don't use channels 12-14 (12 was used, probably
because it appears to have an interrupt, but in reality that
interrupt is for activity on ANY channel). This may explain
a lockup encountered when running out of DMA channels.
The combined effect of this patch is to leave 7 DMA channels
available + channel 0 for bcm2708_fb via the legacy API.
dmaengine: bcm2708: Make legacy API available for bcm2835-dma
bcm2708_fb uses the legacy DMA API, so in order to start using
bcm2835-dma, bcm2835-dma has to support the legacy API. Make this
possible by exporting bcm_dmaman_probe() and bcm_dmaman_remove().
popcornmix [Wed, 17 Jun 2015 16:06:34 +0000 (17:06 +0100)]
bcm2708 framebuffer driver
Signed-off-by: popcornmix <popcornmix@gmail.com>
bcm2708_fb : Implement blanking support using the mailbox property interface
bcm2708_fb: Add pan and vsync controls
bcm2708_fb: DMA acceleration for fb_copyarea
Based on http://www.raspberrypi.org/phpBB3/viewtopic.php?p=62425#p62425
Also used Simon's dmaer_master module as a reference for tweaking DMA
settings for better performance.
For now busylooping only. IRQ support might be added later.
With non-overclocked Raspberry Pi, the performance is ~360 MB/s
for simple copy or ~260 MB/s for two-pass copy (used when dragging
windows to the right).
In the case of using DMA channel 0, the performance improves
to ~440 MB/s.
For comparison, VFP optimized CPU copy can only do ~114 MB/s in
the same conditions (hindered by reading uncached source buffer).
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
bcm2708_fb: report number of dma copies
Add a counter (exported via debugfs) reporting the
number of dma copies that the framebuffer driver
has done, in order to help evaluate different
optimization strategies.
Signed-off-by: Luke Diamand <luked@broadcom.com>
bcm2708_fb: use IRQ for DMA copies
The copyarea ioctl() uses DMA to speed things along. This
was busy-waiting for completion. This change supports using
an interrupt instead for larger transfers. For small
transfers, busy-waiting is still likely to be faster.
Signed-off-by: Luke Diamand <luke@diamand.org>
bcm2708: Make ioctl logging quieter
video: fbdev: bcm2708_fb: Don't panic on error
No need to panic the kernel if the video driver fails.
Just print a message and return an error.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
fbdev: bcm2708_fb: Add ARCH_BCM2835 support
Add Device Tree support.
Pass the device to dma_alloc_coherent() in order to get the
correct bus address on ARCH_BCM2835.
Use the new DMA legacy API header file.
Including <mach/platform.h> is not necessary.
Signed-off-by: Kari Suvanto <karis79@gmail.com>
usb: dwc: fix inconsistent lock state
Signed-off-by: Kari Suvanto <karis79@gmail.com>
Add FIQ patch to dwc_otg driver. Enable with dwc_otg.fiq_fix_enable=1. Should give about 10% more ARM performance.
Thanks to Gordon and Costas
Avoid dynamic memory allocation for channel lock in USB driver. Thanks ddv2005.
Add NAK holdoff scheme. Enabled by default, disable with dwc_otg.nak_holdoff_enable=0. Thanks gsh
Make sure we wait for the reset to finish
dwc_otg: fix bug in dwc_otg_hcd.c resulting in silent kernel
memory corruption, escalating to OOPS under high USB load.
dwc_otg: Fix unsafe access of QTD during URB enqueue
In dwc_otg_hcd_urb_enqueue during qtd creation, it was possible that the
transaction could complete almost immediately after the qtd was assigned
to a host channel during URB enqueue, which meant the qtd pointer was no
longer valid having been completed and removed. Usually, this resulted in
an OOPS during URB submission. By predetermining whether transactions
need to be queued or not, this unsafe pointer access is avoided.
This bug was only evident on the Pi model A where a device was attached
that had no periodic endpoints (e.g. USB pendrive or some wlan devices).
If the memory allocation for a dwc_otg_urb failed, the kernel would OOPS
because for some reason a member of the *unallocated* struct was set to
zero. Error handling changed to fail correctly.
dwc_otg: fix potential use-after-free case in interrupt handler
If a transaction had previously aborted, certain interrupts are
enabled to track error counts and reset where necessary. On IN
endpoints the host generates an ACK interrupt near-simultaneously
with completion of transfer. In the case where this transfer had
previously had an error, this results in a use-after-free on
the QTD memory space with a 1-byte length being overwritten to
0x00.
dwc_otg: add handling of SPLIT transaction data toggle errors
Previously a data toggle error on packets from a USB1.1 device behind
a TT would result in the Pi locking up as the driver never handled
the associated interrupt. Patch adds basic retry mechanism and
interrupt acknowledgement to cater for either a chance toggle error or
for devices that have a broken initial toggle state (FT8U232/FT232BM).
dwc_otg: implement tasklet for returning URBs to usbcore hcd layer
The dwc_otg driver interrupt handler for transfer completion will spend
a very long time with interrupts disabled when a URB is completed -
this is because usb_hcd_giveback_urb is called from within the handler
which for a USB device driver with complicated processing (e.g. webcam)
will take an exorbitant amount of time to complete. This results in
missed completion interrupts for other USB packets which lead to them
being dropped due to microframe overruns.
This patch splits returning the URB to the usb hcd layer into a
high-priority tasklet. This will have most benefit for isochronous IN
transfers but will also have incidental benefit where multiple periodic
devices are active at once.
dwc_otg: fix NAK holdoff and allow on split transactions only
This corrects a bug where if a single active non-periodic endpoint
had at least one transaction in its qh, on frnum == MAX_FRNUM the qh
would get skipped and never get queued again. This would result in
a silent device until error detection (automatic or otherwise) would
either reset the device or flush and requeue the URBs.
Additionally the NAK holdoff was enabled for all transactions - this
would potentially stall a HS endpoint for 1ms if a previous error state
enabled this interrupt and the next response was a NAK. Fix so that
only split transactions get held off.
dwc_otg: Call usb_hcd_unlink_urb_from_ep with lock held in completion handler
usb_hcd_unlink_urb_from_ep must be called with the HCD lock held. Calling it
asynchronously in the tasklet was not safe (regression in c4564d4a1a0a9b10d4419e48239f5d99e88d2667).
This change unlinks it from the endpoint prior to queueing it for handling in
the tasklet, and also adds a check to ensure the urb is OK to be unlinked
before doing so.
NULL pointer dereference kernel oopses had been observed in usb_hcd_giveback_urb
when a USB device was unplugged/replugged during data transfer. This effect
was reproduced using automated USB port power control, hundreds of replug
events were performed during active transfers to confirm that the problem was
eliminated.
USB fix using a FIQ to implement split transactions
This commit adds a FIQ implementaion that schedules
the split transactions using a FIQ so we don't get
held off by the interrupt latency of Linux
dwc_otg: fix device attributes and avoid kernel warnings on boot
dcw_otg: avoid logging function that can cause panics
See: https://github.com/raspberrypi/firmware/issues/21
Thanks to cleverca22 for fix
dwc_otg: mask correct interrupts after transaction error recovery
The dwc_otg driver will unmask certain interrupts on a transaction
that previously halted in the error state in order to reset the
QTD error count. The various fine-grained interrupt handlers do not
consider that other interrupts besides themselves were unmasked.
By disabling the two other interrupts only ever enabled in DMA mode
for this purpose, we can avoid unnecessary function calls in the
IRQ handler. This will also prevent an unneccesary FIQ interrupt
from being generated if the FIQ is enabled.
dwc_otg: fiq: prevent FIQ thrash and incorrect state passing to IRQ
In the case of a transaction to a device that had previously aborted
due to an error, several interrupts are enabled to reset the error
count when a device responds. This has the side-effect of making the
FIQ thrash because the hardware will generate multiple instances of
a NAK on an IN bulk/interrupt endpoint and multiple instances of ACK
on an OUT bulk/interrupt endpoint. Make the FIQ mask and clear the
associated interrupts.
Additionally, on non-split transactions make sure that only unmasked
interrupts are cleared. This caused a hard-to-trigger but serious
race condition when you had the combination of an endpoint awaiting
error recovery and a transaction completed on an endpoint - due to
the sequencing and timing of interrupts generated by the dwc_otg core,
it was possible to confuse the IRQ handler.
Fix function tracing
dwc_otg: whitespace cleanup in dwc_otg_urb_enqueue
dwc_otg: prevent OOPSes during device disconnects
The dwc_otg_urb_enqueue function is thread-unsafe. In particular the
access of urb->hcpriv, usb_hcd_link_urb_to_ep, dwc_otg_urb->qtd and
friends does not occur within a critical section and so if a device
was unplugged during activity there was a high chance that the
usbcore hub_thread would try to disable the endpoint with partially-
formed entries in the URB queue. This would result in BUG() or null
pointer dereferences.
Fix so that access of urb->hcpriv, enqueuing to the hardware and
adding to usbcore endpoint URB lists is contained within a single
critical section.
dwc_otg: prevent BUG() in TT allocation if hub address is > 16
A fixed-size array is used to track TT allocation. This was
previously set to 16 which caused a crash because
dwc_otg_hcd_allocate_port would read past the end of the array.
This was hit if a hub was plugged in which enumerated as addr > 16,
due to previous device resets or unplugs.
Also add #ifdef FIQ_DEBUG around hcd->hub_port_alloc[], which grows
to a large size if 128 hub addresses are supported. This field is
for debug only for tracking which frame an allocate happened in.
dwc_otg: make channel halts with unknown state less damaging
If the IRQ received a channel halt interrupt through the FIQ
with no other bits set, the IRQ would not release the host
channel and never complete the URB.
Add catchall handling to treat as a transaction error and retry.
dwc_otg: fiq_split: use TTs with more granularity
This fixes certain issues with split transaction scheduling.
- Isochronous multi-packet OUT transactions now hog the TT until
they are completed - this prevents hubs aborting transactions
if they get a periodic start-split out-of-order
- Don't perform TT allocation on non-periodic endpoints - this
allows simultaneous use of the TT's bulk/control and periodic
transaction buffers
This commit will mainly affect USB audio playback.
dwc_otg: fix potential sleep while atomic during urb enqueue
Fixes a regression introduced with eb1b482a. Kmalloc called from
dwc_otg_hcd_qtd_add / dwc_otg_hcd_qtd_create did not always have
the GPF_ATOMIC flag set. Force this flag when inside the larger
critical section.
dwc_otg: make fiq_split_enable imply fiq_fix_enable
Failing to set up the FIQ correctly would result in
"IRQ 32: nobody cared" errors in dmesg.
dwc_otg: prevent crashes on host port disconnects
Fix several issues resulting in crashes or inconsistent state
if a Model A root port was disconnected.
- Clean up queue heads properly in kill_urbs_in_qh_list by
removing the empty QHs from the schedule lists
- Set the halt status properly to prevent IRQ handlers from
using freed memory
- Add fiq_split related cleanup for saved registers
- Make microframe scheduling reclaim host channels if
active during a disconnect
- Abort URBs with -ESHUTDOWN status response, informing
device drivers so they respond in a more correct fashion
and don't try to resubmit URBs
- Prevent IRQ handlers from attempting to handle channel
interrupts if the associated URB was dequeued (and the
driver state was cleared)
dwc_otg: prevent leaking URBs during enqueue
A dwc_otg_urb would get leaked if the HCD enqueue function
failed for any reason. Free the URB at the appropriate points.
dwc_otg: Enable NAK holdoff for control split transactions
Certain low-speed devices take a very long time to complete a
data or status stage of a control transaction, producing NAK
responses until they complete internal processing - the USB2.0
spec limit is up to 500mS. This causes the same type of interrupt
storm as seen with USB-serial dongles prior to c8edb238.
In certain circumstances, usually while booting, this interrupt
storm could cause SD card timeouts.
dwc_otg: Fix for occasional lockup on boot when doing a USB reset
dwc_otg: Don't issue traffic to LS devices in FS mode
Issuing low-speed packets when the root port is in full-speed mode
causes the root port to stop responding. Explicitly fail when
enqueuing URBs to a LS endpoint on a FS bus.
Fix ARM architecture issue with local_irq_restore()
If local_fiq_enable() is called before a local_irq_restore(flags) where
the flags variable has the F bit set, the FIQ will be erroneously disabled.
Fixup arch_local_irq_restore to avoid trampling the F bit in CPSR.
Also fix some of the hacks previously implemented for previous dwc_otg
incarnations.
dwc_otg: fiq_fsm: Base commit for driver rewrite
This commit removes the previous FIQ fixes entirely and adds fiq_fsm.
This rewrite features much more complete support for split transactions
and takes into account several OTG hardware bugs. High-speed
isochronous transactions are also capable of being performed by fiq_fsm.
All driver options have been removed and replaced with:
- dwc_otg.fiq_enable (bool)
- dwc_otg.fiq_fsm_enable (bool)
- dwc_otg.fiq_fsm_mask (bitmask)
- dwc_otg.nak_holdoff (unsigned int)
Defaults are specified such that fiq_fsm behaves similarly to the
previously implemented FIQ fixes.
fiq_fsm: Push error recovery into the FIQ when fiq_fsm is used
If the transfer associated with a QTD failed due to a bus error, the HCD
would retry the transfer up to 3 times (implementing the USB2.0
three-strikes retry in software).
Due to the masking mechanism used by fiq_fsm, it is only possible to pass
a single interrupt through to the HCD per-transfer.
In this instance host channels would fall off the radar because the error
reset would function, but the subsequent channel halt would be lost.
Push the error count reset into the FIQ handler.
fiq_fsm: Implement timeout mechanism
For full-speed endpoints with a large packet size, interrupt latency
runs the risk of the FIQ starting a transaction too late in a full-speed
frame. If the device is still transmitting data when EOF2 for the
downstream frame occurs, the hub will disable the port. This change is
not reflected in the hub status endpoint and the device becomes
unresponsive.
Prevent high-bandwidth transactions from being started too late in a
frame. The mechanism is not guaranteed: a combination of bit stuffing
and hub latency may still result in a device overrunning.
fiq_fsm: fix bounce buffer utilisation for Isochronous OUT
Multi-packet isochronous OUT transactions were subject to a few bounday
bugs. Fix them.
Audio playback is now much more robust: however, an issue stands with
devices that have adaptive sinks - ALSA plays samples too fast.
dwc_otg: Return full-speed frame numbers in HS mode
The frame counter increments on every *microframe* in high-speed mode.
Most device drivers expect this number to be in full-speed frames - this
caused considerable confusion to e.g. snd_usb_audio which uses the
frame counter to estimate the number of samples played.
fiq_fsm: save PID on completion of interrupt OUT transfers
Also add edge case handling for interrupt transports.
Note that for periodic split IN, data toggles are unimplemented in the
OTG host hardware - it unconditionally accepts any PID.
fiq_fsm: add missing case for fiq_fsm_tt_in_use()
Certain combinations of bitrate and endpoint activity could
result in a periodic transaction erroneously getting started
while the previous Isochronous OUT was still active.
fiq_fsm: clear hcintmsk for aborted transactions
Prevents the FIQ from erroneously handling interrupts
on a timed out channel.
fiq_fsm: enable by default
fiq_fsm: fix dequeues for non-periodic split transactions
If a dequeue happened between the SSPLIT and CSPLIT phases of the
transaction, the HCD would never receive an interrupt.
fiq_fsm: Disable by default
fiq_fsm: Handle HC babble errors
The HCTSIZ transfer size field raises a babble interrupt if
the counter wraps. Handle the resulting interrupt in this case.
dwc_otg: fix interrupt registration for fiq_enable=0
Additionally make the module parameter conditional for wherever
hcd->fiq_state is touched.
fiq_fsm: Enable by default
dwc_otg: Fix various issues with root port and transaction errors
Process the host port interrupts correctly (and don't trample them).
Root port hotplug now functional again.
Fix a few thinkos with the transaction error passthrough for fiq_fsm.
fiq_fsm: Implement hack for Split Interrupt transactions
Hubs aren't too picky about which endpoint we send Control type split
transactions to. By treating Interrupt transfers as Control, it is
possible to use the non-periodic queue in the OTG core as well as the
non-periodic FIFOs in the hub itself. This massively reduces the
microframe exclusivity/contention that periodic split transactions
otherwise have to enforce.
It goes without saying that this is a fairly egregious USB specification
violation, but it works.
Original idea by Hans Petter Selasky @ FreeBSD.org.
dwc_otg: FIQ support on SMP. Set up FIQ stack and handler on Core 0 only.
dwc_otg: introduce fiq_fsm_spin(un|)lock()
SMP safety for the FIQ relies on register read-modify write cycles being
completed in the correct order. Several places in the DWC code modify
registers also touched by the FIQ. Protect these by a bare-bones lock
mechanism.
This also makes it possible to run the FIQ and IRQ handlers on different
cores.
fiq_fsm: fix build on bcm2708 and bcm2709 platforms
dwc_otg: put some barriers back where they should be for UP
bcm2709/dwc_otg: Setup FIQ on core 1 if >1 core active
dwc_otg: fixup read-modify-write in critical paths
Be more careful about read-modify-write on registers that the FIQ
also touches.
Guard fiq_fsm_spin_lock with fiq_enable check
fiq_fsm: Falling out of the state machine isn't fatal
This edge case can be hit if the port is disabled while the FIQ is
in the middle of a transaction. Make the effects less severe.
Also get rid of the useless return value.
squash: dwc_otg: Allow to build without SMP
usb: core: make overcurrent messages more prominent
Hub overcurrent messages are more serious than "debug". Increase loglevel.
usb: dwc_otg: Don't use dma_to_virt()
Commit 6ce0d20 changes dma_to_virt() which breaks this driver.
Open code the old dma_to_virt() implementation to work around this.
Limit the use of __bus_to_virt() to cases where transfer_buffer_length
is set and transfer_buffer is not set. This is done to increase the
chance that this driver will also work on ARCH_BCM2835.
transfer_buffer should not be NULL if the length is set, but the
comment in the code indicates that there are situations where this
might happen. drivers/usb/isp1760/isp1760-hcd.c also has a similar
comment pointing to a possible: 'usb storage / SCSI bug'.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Fix crash when fiq_enable=0
dwc_otg: fiq_fsm: Make high-speed isochronous strided transfers work properly
Certain low-bandwidth high-speed USB devices (specialist audio devices,
compressed-frame webcams) have packet intervals > 1 microframe.
Stride these transfers in the FIQ by using the start-of-frame interrupt
to restart the channel at the right time.
dwc_otg: Force host mode to fix incorrect compute module boards
dwc_otg: Add ARCH_BCM2835 support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Simplify FIQ irq number code
Dropping ATAGS means we can simplify the FIQ irq number code.
Also add error checking on the returned irq number.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Remove duplicate gadget probe/unregister function
dwc_otg: Properly set the HFIR
Douglas Anderson reported:
According to the most up to date version of the dwc2 databook, the FRINT
field of the HFIR register should be programmed to:
* 125 us * (PHY clock freq for HS) - 1
* 1000 us * (PHY clock freq for FS/LS) - 1
This is opposed to older versions of the doc that claimed it should be:
* 125 us * (PHY clock freq for HS)
* 1000 us * (PHY clock freq for FS/LS)
and reported lower timing jitter on a USB analyser
dcw_otg: trim xfer length when buffer larger than allocated size is received
dwc_otg: Don't free qh align buffers in atomic context
dwc_otg: Enable the hack for Split Interrupt transactions by default
dwc_otg.fiq_fsm_mask=0xF has long been a suggestion for users with audio stutters or other USB bandwidth issues.
So far we are aware of many success stories but no failure caused by this setting.
Make it a default to learn more.
Martin Sperl [Fri, 2 Sep 2016 15:45:27 +0000 (16:45 +0100)]
Register the clocks early during the boot process,
so that special/critical clocks can get enabled early on
in the boot process avoiding the risk of disabling a clock,
pll_divider or pll when a claiming driver fails to install
propperly - maybe it needs to defer.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Noralf Trønnes [Fri, 7 Oct 2016 14:50:59 +0000 (16:50 +0200)]
watchdog: bcm2835: Support setting reboot partition
The Raspberry Pi firmware looks at the RSTS register to know which
partition to boot from. The reboot syscall command
LINUX_REBOOT_CMD_RESTART2 supports passing in a string argument.
Add support for passing in a partition number 0..63 to boot from.
Partition 63 is a special partiton indicating halt.
If the partition doesn't exist, the firmware falls back to partition 0.
Noralf Trønnes [Sat, 3 Oct 2015 20:22:55 +0000 (22:22 +0200)]
dmaengine: bcm2835: Load driver early and support legacy API
Load driver early since at least bcm2708_fb doesn't support deferred
probing and even if it did, we don't want the video driver deferred.
Support the legacy DMA API which is needed by bcm2708_fb.
Don't mask out channel 2.
Noralf Trønnes [Wed, 3 Jun 2015 10:26:13 +0000 (12:26 +0200)]
ARM: bcm2835: Set Serial number and Revision
The VideoCore bootloader passes in Serial number and
Revision number through Device Tree. Make these available to
userspace through /proc/cpuinfo.
Mainline status:
There is a commit in linux-next that standardize passing the serial
number through Device Tree (string: /serial-number):
ARM: 8355/1: arch: Show the serial number from devicetree in cpuinfo
There was an attempt to do the same with the revision number, but it
didn't get in:
[PATCH v2 1/2] arm: devtree: Set system_rev from DT revision
Phil Elwell [Wed, 24 Jun 2015 13:10:44 +0000 (14:10 +0100)]
spi-bcm2835: Support pin groups other than 7-11
The spi-bcm2835 driver automatically uses GPIO chip-selects due to
some unreliability of the native ones. In doing so it chooses the
same pins as the native chip-selects would use, but the existing
code always uses pins 7 and 8, wherever the SPI function is mapped.
Search the pinctrl group assigned to the driver for pins that
correspond to native chip-selects, and use those for GPIO chip-
selects.
Phil Elwell [Thu, 26 Feb 2015 09:58:22 +0000 (09:58 +0000)]
pinctrl-bcm2835: Only request the interrupts listed in the DTB
Although the GPIO controller can generate three interrupts (four counting
the common one), the device tree files currently only specify two. In the
absence of the third, simply don't register that interrupt (as opposed to
registering 0), which has the effect of making it impossible to generate
interrupts for GPIOs 46-53 which, since they share pins with the SD card
interface, is unlikely to be a problem.
Noralf Trønnes [Fri, 12 Jun 2015 17:01:05 +0000 (19:01 +0200)]
irqchip: bcm2835: Add FIQ support
Add a duplicate irq range with an offset on the hwirq's so the
driver can detect that enable_fiq() is used.
Tested with downstream dwc_otg USB controller driver.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org> Reviewed-by: Eric Anholt <eric@anholt.net> Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Phil Elwell [Fri, 4 Dec 2015 17:41:50 +0000 (17:41 +0000)]
irq-bcm2836: Prevent spurious interrupts, and trap them early
The old arch-specific IRQ macros included a dsb to ensure the
write to clear the mailbox interrupt completed before returning
from the interrupt. The BCM2836 irqchip driver needs the same
precaution to avoid spurious interrupts.
Spurious interrupts are still possible for other reasons,
though, so trap them early.
Eric Anholt [Fri, 19 Dec 2014 00:07:15 +0000 (16:07 -0800)]
mm: Remove the PFN busy warning
See commit dae803e165a11bc88ca8dbc07a11077caf97bbcb -- the warning is
expected sometimes when using CMA. However, that commit still spams
my kernel log with these warnings.
BugLink: https://bugs.launchpad.net/bugs/1715812
When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.
As last step, we can remove the pending_confirm flag.
Reported-by: YueHaibing <yuehaibing@huawei.com> Fixes: 5110effee8fd ("net: Do delayed neigh confirmation.") Fixes: f2bb4bedf35d ("ipv4: Cache output routes in fib_info nexthops.") Signed-off-by: Julian Anastasov <ja@ssi.bg> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 51ce8bd4d17a761e1a90a34a1b5c9b762cce7553) Signed-off-by: Daniel Axtens <daniel.axtens@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
net: use dst_confirm_neigh for UDP, RAW, ICMP, L2TP
BugLink: https://bugs.launchpad.net/bugs/1715812
When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.
The datagram protocols can use MSG_CONFIRM to confirm the
neighbour. When used with MSG_PROBE we do not reach the
code where neighbour is confirmed, so we have to do the
same slow lookup by using the dst_confirm_neigh() helper.
When MSG_PROBE is not used, ip_append_data/ip6_append_data
will set the skb flag dst_pending_confirm.
Reported-by: YueHaibing <yuehaibing@huawei.com> Fixes: 5110effee8fd ("net: Do delayed neigh confirmation.") Fixes: f2bb4bedf35d ("ipv4: Cache output routes in fib_info nexthops.") Signed-off-by: Julian Anastasov <ja@ssi.bg> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 0dec879f636f11b0ffda1cb5fd96a1754c59ead3) Signed-off-by: Daniel Axtens <daniel.axtens@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
projects / mirror_ubuntu-zesty-kernel.git / log