Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
SDM845 has ETMv4.2 and can use the existing etm4x driver.
But the current etm driver checks only for ETMv4.0 and
errors out for other etm4x versions. This patch adds this
missing support to enable SoC's with ETMv4x to use same
driver by checking only the ETM architecture major version
number.
Without this change, we get below error during etm probe:
/ # dmesg | grep etm
[ 6.660093] coresight-etm4x: probe of 7040000.etm failed with error -22
[ 6.666902] coresight-etm4x: probe of 7140000.etm failed with error -22
[ 6.673708] coresight-etm4x: probe of 7240000.etm failed with error -22
[ 6.680511] coresight-etm4x: probe of 7340000.etm failed with error -22
[ 6.687313] coresight-etm4x: probe of 7440000.etm failed with error -22
[ 6.694113] coresight-etm4x: probe of 7540000.etm failed with error -22
[ 6.700914] coresight-etm4x: probe of 7640000.etm failed with error -22
[ 6.707717] coresight-etm4x: probe of 7740000.etm failed with error -22
When building with -Wsometimes-uninitialized, Clang warns:
arch/powerpc/xmon/ppc-dis.c:157:7: warning: variable 'opcode' is used
uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
if (cpu_has_feature(CPU_FTRS_POWER9))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/powerpc/xmon/ppc-dis.c:167:7: note: uninitialized use occurs here
if (opcode == NULL)
^~~~~~
arch/powerpc/xmon/ppc-dis.c:157:3: note: remove the 'if' if its
condition is always true
if (cpu_has_feature(CPU_FTRS_POWER9))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/powerpc/xmon/ppc-dis.c:132:38: note: initialize the variable
'opcode' to silence this warning
const struct powerpc_opcode *opcode;
^
= NULL
1 warning generated.
This warning seems to make no sense on the surface because opcode is set
to NULL right below this statement. However, there is a comma instead of
semicolon to end the dialect assignment, meaning that the opcode
assignment only happens in the if statement. Properly terminate that
line so that Clang no longer warns.
We had a test-report where, under memory pressure, adding LUNs to the
systems would fail (the tests add LUNs strictly in sequence):
[ 5525.853432] scsi 0:0:1:1088045124: Direct-Access IBM 2107900 .148 PQ: 0 ANSI: 5
[ 5525.853826] scsi 0:0:1:1088045124: alua: supports implicit TPGS
[ 5525.853830] scsi 0:0:1:1088045124: alua: device naa.6005076303ffd32700000000000044da port group 0 rel port 43
[ 5525.853931] sd 0:0:1:1088045124: Attached scsi generic sg10 type 0
[ 5525.854075] sd 0:0:1:1088045124: [sdk] Disabling DIF Type 1 protection
[ 5525.855495] sd 0:0:1:1088045124: [sdk] 2097152 512-byte logical blocks: (1.07 GB/1.00 GiB)
[ 5525.855606] sd 0:0:1:1088045124: [sdk] Write Protect is off
[ 5525.855609] sd 0:0:1:1088045124: [sdk] Mode Sense: ed 00 00 08
[ 5525.855795] sd 0:0:1:1088045124: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5525.857838] sdk: sdk1
[ 5525.859468] sd 0:0:1:1088045124: [sdk] Attached SCSI disk
[ 5525.865073] sd 0:0:1:1088045124: alua: transition timeout set to 60 seconds
[ 5525.865078] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.015070] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.015213] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.587439] scsi_alloc_sdev: Allocation failure during SCSI scanning, some SCSI devices might not be configured
[ 5526.588562] scsi_alloc_sdev: Allocation failure during SCSI scanning, some SCSI devices might not be configured
Looking at the code of scsi_alloc_sdev(), and all the calling contexts,
there seems to be no reason to use GFP_ATMOIC here. All the different
call-contexts use a mutex at some point, and nothing in between that
requires no sleeping, as far as I could see. Additionally, the code that
later allocates the block queue for the device (scsi_mq_alloc_queue())
already uses GFP_KERNEL.
There are similar allocations in two other functions:
scsi_probe_and_add_lun(), and scsi_add_lun(),; that can also be done with
GFP_KERNEL.
Here is the contexts for the three functions so far:
According to the chipidea driver bindings, the USB PHY is specified via
the "phys" phandle node. However, this only takes effect for USB PHYs
that use the common PHY framework. For legacy USB PHYs, a simple lookup
based on the USB PHY type is done instead.
This does not play out well when more than one USB PHY is registered,
since the first registered PHY matching the type will always be
returned regardless of what the driver was bound to.
Fix this by looking up the PHY based on the "phys" phandle node.
Although generic PHYs are rather matched by their "phys-name" and not
the "phys" phandle directly, there is no helper for similar lookup on
legacy PHYs and it's probably not worth the effort to add it.
When no legacy USB PHY is found by phandle, fallback to grabbing any
registered USB2 PHY. This ensures backward compatibility if some users
were actually relying on this mechanism.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The cavium/zip implementation of the deflate compression algorithm is
incorrectly being registered under the generic driver name, which
prevents the generic implementation from being registered with the
crypto API when CONFIG_CRYPTO_DEV_CAVIUM_ZIP=y. Similarly the lzs
algorithm (which does not currently have a generic implementation...)
is incorrectly being registered as lzs-generic.
Fix the naming collision by adding a suffix "-cavium" to the
cra_driver_name of the cavium/zip algorithms.
Fixes: 640035a2dc55 ("crypto: zip - Add ThunderX ZIP driver core") Cc: Mahipal Challa <mahipalreddy2006@gmail.com> Cc: Jan Glauber <jglauber@cavium.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
e = f(...);
... when != of_node_put(e)
when != x = e
when != e = x
when any
if (<+...of_device_is_available(e)...+>) {
... when != of_node_put(e)
(
return e;
|
+ of_node_put(e);
return ...;
)
}
// </smpl>
Fixes: 5343e674f32fb ("crypto4xx: integrate ppc4xx-rng into crypto4xx") Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
ies1 or ies2 might be null when code inside
_wil_cfg80211_merge_extra_ies access them.
Add explicit check for null and make sure ies1/ies2 are not
accessed in such a case.
spos might be null and be accessed inside
_wil_cfg80211_merge_extra_ies.
Add explicit check for null in the while condition statement
and make sure spos is not accessed in such a case.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
It is incorrect to call pcie_pme_suspend() from pcie_pme_remove() for two
reasons.
First, pcie_pme_suspend() calls synchronize_irq(), which will wait for the
native hotplug interrupt handler as well as for the PME one, because they
share one IRQ (as per the spec). That may deadlock if hotplug is signaled
while pcie_pme_remove() is running and the latter calls
pci_lock_rescan_remove() before the former.
Second, if pcie_pme_suspend() figures out that wakeup needs to be enabled
for the port, it will return without disabling the interrupt as expected by
pcie_pme_remove() which was overlooked by commit c7b5a4e6e8fb ("PCI / PM:
Fix native PME handling during system suspend/resume").
To fix that, rework pcie_pme_remove() to disable the PME interrupt, clear
its status and prevent the PME worker function from re-enabling it before
calling free_irq() on it, which should be sufficient.
Fixes: c7b5a4e6e8fb ("PCI / PM: Fix native PME handling during system suspend/resume") Link: https://lore.kernel.org/linux-pci/c7697e7c-e1af-13e4-8491-0a3996e6ab5d@huawei.com Reported-by: Dongdong Liu <liudongdong3@huawei.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[bhelgaas: add URL and deadlock details from Dongdong] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
guard_bio_eod() can truncate a segment in bio to allow it to do IO on
odd last sectors of a device.
It already checks if the IO starts past EOD, but it does not consider
the possibility of an IO request starting within device boundaries can
contain more than one segment past EOD.
In such cases, truncated_bytes can be bigger than PAGE_SIZE, and will
underflow bvec->bv_len.
Fix this by checking if truncated_bytes is lower than PAGE_SIZE.
This situation has been found on filesystems such as isofs and vfat,
which doesn't check the device size before mount, if the device is
smaller than the filesystem itself, a readahead on such filesystem,
which spans EOD, can trigger this situation, leading a call to
zero_user() with a wrong size possibly corrupting memory.
I didn't see any crash, or didn't let the system run long enough to
check if memory corruption will be hit somewhere, but adding
instrumentation to guard_bio_end() to check truncated_bytes size, was
enough to see the error.
In jbd2_journal_commit_transaction(), if we are in abort mode,
we may flush the buffer without setting descriptor block checksum
by goto start_journal_io. Then fs is mounted,
jbd2_descriptor_block_csum_verify() failed.
Fix this by adding a NULL check on devname in cifs_parse_devname()
Signed-off-by: Yao Liu <yotta.liu@ucloud.cn> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Invoking dm_get_device() twice on the same device path with different
modes is dangerous. Because in that case, upgrade_mode() will alloc a
new 'dm_dev' and free the old one, which may be referenced by a previous
caller. Dereferencing the dangling pointer will trigger kernel NULL
pointer dereference.
The following two cases can reproduce this issue. Actually, they are
invalid setups that must be disallowed, e.g.:
1. Creating a thin-pool with read_only mode, and the same device as
both metadata and data.
When compiling with -Wformat, clang emits the following warnings:
fs/cifs/smb1ops.c:312:20: warning: format specifies type 'unsigned
short' but the argument has type 'unsigned int' [-Wformat]
tgt_total_cnt, total_in_tgt);
^~~~~~~~~~~~
fs/cifs/cifs_dfs_ref.c:289:4: warning: format specifies type 'short'
but the argument has type 'int' [-Wformat]
ref->flags, ref->server_type);
^~~~~~~~~~
fs/cifs/cifs_dfs_ref.c:289:16: warning: format specifies type 'short'
but the argument has type 'int' [-Wformat]
ref->flags, ref->server_type);
^~~~~~~~~~~~~~~~
fs/cifs/cifs_dfs_ref.c:291:4: warning: format specifies type 'short'
but the argument has type 'int' [-Wformat]
ref->ref_flag, ref->path_consumed);
^~~~~~~~~~~~~
fs/cifs/cifs_dfs_ref.c:291:19: warning: format specifies type 'short'
but the argument has type 'int' [-Wformat]
ref->ref_flag, ref->path_consumed);
^~~~~~~~~~~~~~~~~~
The types of these arguments are unconditionally defined, so this patch
updates the format character to the correct ones for ints and unsigned
ints.
Link: https://github.com/ClangBuiltLinux/linux/issues/378 Signed-off-by: Louis Taylor <louis@kragniz.eu> Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
(Taken from https://bugzilla.kernel.org/show_bug.cgi?id=200647)
'get_unused_fd_flags' in kthread cause kernel crash. It works fine on
4.1, but causes crash after get 64 fds. It also cause crash on
ubuntu1404/1604/1804, centos7.5, and the crash messages are almost the
same.
This issue exists since CentOS 7.5 3.10.0-862 and CentOS 7.4
(3.10.0-693.21.1 ) is ok. Root cause: the item 'resize_wait' is not
initialized before being used.
Reported-by: Richard Zhang <zhang.zijian@h3c.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In the process of creating a node, it will cause NULL pointer
dereference in kernel if o2cb_ctl failed in the interval (mkdir,
o2cb_set_node_attribute(node_num)] in function o2cb_add_node.
The node num is initialized to 0 in function o2nm_node_group_make_item,
o2nm_node_group_drop_item will mistake the node number 0 for a valid
node number when we delete the node before the node number is set
correctly. If the local node number of the current host happens to be
0, cluster->cl_local_node will be set to O2NM_INVALID_NODE_NUM while
o2hb_thread still running. The panic stack is generated as follows:
Kmemleak does not track the array cache (alc->ac) but the alien cache
(alc) instead, so let it track the latter by lifting kmemleak_no_scan()
out of init_arraycache().
There is another place that calls init_arraycache(), but
alloc_kmem_cache_cpus() uses the percpu allocation where will never be
considered as a leak.
As it's difficult to report where exactly the uninit value resides in
the mempolicy object, we have to guess a bit. mm/mempolicy.c:353
contains this part of mpol_rebind_policy():
if (!mpol_store_user_nodemask(pol) &&
nodes_equal(pol->w.cpuset_mems_allowed, *newmask))
"mpol_store_user_nodemask(pol)" is testing pol->flags, which I couldn't
ever see being uninitialized after leaving mpol_new(). So I'll guess
it's actually about accessing pol->w.cpuset_mems_allowed on line 354,
but still part of statement starting on line 353.
For w.cpuset_mems_allowed to be not initialized, and the nodes_equal()
reachable for a mempolicy where mpol_set_nodemask() is called in
do_mbind(), it seems the only possibility is a MPOL_PREFERRED policy
with empty set of nodes, i.e. MPOL_LOCAL equivalent, with MPOL_F_LOCAL
flag. Let's exclude such policies from the nodes_equal() check. Note
the uninit access should be benign anyway, as rebinding this kind of
policy is always a no-op. Therefore no actual need for stable
inclusion.
Link: http://lkml.kernel.org/r/a71997c3-e8ae-a787-d5ce-3db05768b27c@suse.cz Link: http://lkml.kernel.org/r/73da3e9c-cc84-509e-17d9-0c434bb9967d@suse.cz Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Reported-by: syzbot+b19c2dc2c990ea657a71@syzkaller.appspotmail.com Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Michal Hocko <mhocko@suse.com> Cc: David Rientjes <rientjes@google.com> Cc: Yisheng Xie <xieyisheng1@huawei.com> Cc: zhong jiang <zhongjiang@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
After offlining a memory block, kmemleak scan will trigger a crash, as
it encounters a page ext address that has already been freed during
memory offlining. At the beginning in alloc_page_ext(), it calls
kmemleak_alloc(), but it does not call kmemleak_free() in
free_page_ext().
Kmemleak is supposed to work with the memblock_{alloc,free} pair and it
ignores the memblock_reserve() as a memblock_alloc() implementation
detail. It is, however, tolerant to memblock_free() being called on
a sub-range or just a different range from a previous memblock_alloc().
So the original patch looks fine to me. FWIW:
Link: http://lkml.kernel.org/r/20190227144631.16708-1-peng.fan@nxp.com Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Reviewed-by: Mike Rapoport <rppt@linux.ibm.com> Cc: Laura Abbott <labbott@redhat.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The pm8xxx_get_channel() implementation is unclear, and causes gcc to
suddenly generate odd warnings. The trigger for the warning (at least
for me) was the entirely unrelated commit 79a4e91d1bb2 ("device.h: Add
__cold to dev_<level> logging functions"), which apparently changes gcc
code generation in the caller function enough to cause this:
drivers/iio/adc/qcom-pm8xxx-xoadc.c: In function ‘pm8xxx_xoadc_probe’:
drivers/iio/adc/qcom-pm8xxx-xoadc.c:633:8: warning: ‘ch’ may be used uninitialized in this function [-Wmaybe-uninitialized]
ret = pm8xxx_read_channel_rsv(adc, ch, AMUX_RSV4,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
&read_nomux_rsv4, true);
~~~~~~~~~~~~~~~~~~~~~~~
drivers/iio/adc/qcom-pm8xxx-xoadc.c:426:27: note: ‘ch’ was declared here
struct pm8xxx_chan_info *ch;
^~
because gcc for some reason then isn't able to see that the termination
condition for the "for( )" loop in that function is also the condition
for returning NULL.
So it's not _actually_ uninitialized, but the function is admittedly
just unnecessarily oddly written.
Simplify and clarify the function, making gcc also see that it always
returns a valid initialized value.
Cc: Joe Perches <joe@perches.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Andy Gross <andy.gross@linaro.org> Cc: David Brown <david.brown@linaro.org> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When the PHY comes down, we currently do not set the negotiated linkrate:
root@(none)$ pwd
/sys/class/sas_phy/phy-0:0
root@(none)$ more enable
1
root@(none)$ more negotiated_linkrate
12.0 Gbit
root@(none)$ echo 0 > enable
root@(none)$ more negotiated_linkrate
12.0 Gbit
root@(none)$
This patch fixes the driver code to set it properly when the PHY comes
down.
If the PHY had been enabled, then set unknown; otherwise, flag as disabled.
The logical place to set the negotiated linkrate for this scenario is PHY
down routine, which is called from the PHY down ISR.
However, it is not possible to know if the PHY comes down due to PHY
disable or loss of link, as sas_phy.enabled member is not set until after
the transport disable routine is complete, which races with the PHY down
ISR.
As an imperfect solution, use sas_phy_data.enable as the flag to know if
the PHY is down due to disable. It's imperfect, as sas_phy_data is internal
to libsas.
I can't see another way without adding a new field to hisi_sas_phy and
managing it, or changing SCSI SAS transport.
Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The enic driver relies on the CONFIG_CPUMASK_OFFSTACK feature to
dynamically allocate a struct member, but this is normally intended for
local variables.
Building with clang, I get a warning for a few locations that check the
address of the cpumask_var_t:
drivers/net/ethernet/cisco/enic/enic_main.c:122:22: error: address of array 'enic->msix[i].affinity_mask' will always evaluate to 'true' [-Werror,-Wpointer-bool-conversion]
As far as I can tell, the code is still correct, as the truth value of
the pointer is what we need in this configuration. To get rid of
the warning, use cpumask_available() instead of checking the
pointer directly.
Fixes: 322cf7e3a4e8 ("enic: assign affinity hint to interrupts") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The percpu member of this structure is declared as:
struct ... ** __percpu member;
So its type is:
__percpu pointer to pointer to struct ...
But looking at how it's used, its type should be:
pointer to __percpu pointer to struct ...
and it should thus be declared as:
struct ... * __percpu *member;
So fix the placement of '__percpu' in the definition of this
structures.
This silents a few Sparse's warnings like:
warning: incorrect type in initializer (different address spaces)
expected void const [noderef] <asn:3> *__vpp_verify
got struct sched_domain **
Link: http://lkml.kernel.org/r/20190118144902.79065-1-luc.vanoostenryck@gmail.com Fixes: 017c59c042d01 ("relay: Use per CPU constructs for the relay channel buffer pointers") Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com> Cc: Jens Axboe <axboe@suse.de> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Tony notes that the GPIO module does not idle when level interrupts are
in use, as the wakeup appears to get stuck.
After extensive investigation, it appears that the wakeup will only be
cleared if the interrupt status register is cleared while the interrupt
is enabled. However, we are currently clearing it with the interrupt
disabled for level-based interrupts.
It is acknowledged that this observed behaviour conflicts with a
statement in the TRM:
CAUTION
After servicing the interrupt, the status bit in the interrupt status
register (GPIOi.GPIO_IRQSTATUS_0 or GPIOi.GPIO_IRQSTATUS_1) must be
reset and the interrupt line released (by setting the corresponding
bit of the interrupt status register to 1) before enabling an
interrupt for the GPIO channel in the interrupt-enable register
(GPIOi.GPIO_IRQSTATUS_SET_0 or GPIOi.GPIO_IRQSTATUS_SET_1) to prevent
the occurrence of unexpected interrupts when enabling an interrupt
for the GPIO channel.
However, this does not appear to be a practical problem.
Further, as reported by Grygorii Strashko <grygorii.strashko@ti.com>,
the TI Android kernel tree has an earlier similar patch as "GPIO: OMAP:
Fix the sequence to clear the IRQ status" saying:
if the status is cleared after disabling the IRQ then sWAKEUP will not
be cleared and gates the module transition
When we unmask the level interrupt after the interrupt has been handled,
enable the interrupt and only then clear the interrupt. If the interrupt
is still pending, the hardware will re-assert the interrupt status.
Should the caution note in the TRM prove to be a problem, we could
use a clear-enable-clear sequence instead.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: Keerthy <j-keerthy@ti.com> Cc: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[tony@atomide.com: updated comments based on an earlier TI patch] Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
As reported back in 2016-11 [1], the "ftdump" kdb command triggers a
BUG for "sleeping function called from invalid context".
kdb's "ftdump" command wants to call ring_buffer_read_prepare() in
atomic context. A very simple solution for this is to add allocation
flags to ring_buffer_read_prepare() so kdb can call it without
triggering the allocation error. This patch does that.
Note that in the original email thread about this, it was suggested
that perhaps the solution for kdb was to either preallocate the buffer
ahead of time or create our own iterator. I'm hoping that this
alternative of adding allocation flags to ring_buffer_read_prepare()
can be considered since it means I don't need to duplicate more of the
core trace code into "trace_kdb.c" (for either creating my own
iterator or re-preparing a ring allocator whose memory was already
allocated).
NOTE: another option for kdb is to actually figure out how to make it
reuse the existing ftrace_dump() function and totally eliminate the
duplication. This sounds very appealing and actually works (the "sr
z" command can be seen to properly dump the ftrace buffer). The
downside here is that ftrace_dump() fully consumes the trace buffer.
Unless that is changed I'd rather not use it because it means "ftdump
| grep xyz" won't be very useful to search the ftrace buffer since it
will throw away the whole trace on the first grep. A future patch to
dump only the last few lines of the buffer will also be hard to
implement.
sometimes, dead lock when make system call SYS_getdents64 with fsync() is
called by another process.
monkey running on android9.0
1. task 9785 held sbi->cp_rwsem and waiting lock_page()
2. task 10349 held mm_sem and waiting sbi->cp_rwsem
3. task 9709 held lock_page() and waiting mm_sem
Since f2fs_readdir is protected by inode.i_rwsem, there should not be
any updates in inode page, we're safe to lookup dents in inode page
without its lock held, so taking off the lock to improve concurrency
of readdir and avoid potential deadlock.
Reported-by: Jiqun Li <jiqun.li@unisoc.com> Signed-off-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
It believe it is a bad idea to hardcode a specific compiler prefix
that may or may not be installed on a user's system. It is annoying
when testing features that should not require compilers at all.
For example, mrproper, headers_install, etc. should work without
any compiler.
They look like follows on my machine.
$ make ARCH=h8300 mrproper
./scripts/gcc-version.sh: line 26: h8300-unknown-linux-gcc: command not found
./scripts/gcc-version.sh: line 27: h8300-unknown-linux-gcc: command not found
make: h8300-unknown-linux-gcc: Command not found
make: h8300-unknown-linux-gcc: Command not found
[ a bunch of the same error messages continue ]
$ make ARCH=h8300 headers_install
./scripts/gcc-version.sh: line 26: h8300-unknown-linux-gcc: command not found
./scripts/gcc-version.sh: line 27: h8300-unknown-linux-gcc: command not found
make: h8300-unknown-linux-gcc: Command not found
HOSTCC scripts/basic/fixdep
make: h8300-unknown-linux-gcc: Command not found
WRAP arch/h8300/include/generated/uapi/asm/kvm_para.h
[ snip ]
The solution is to delete this line, or to use cc-cross-prefix like
some architectures do. I chose the latter as a moderate fixup.
I added an alternative 'h8300-linux-' because it is available at:
Notice how we don't call locks_lock_file_wait() which does the
generic VFS lock/unlock/wait work on the inode if rc != 0.
If we are closing the handle, the SMB server is supposed to remove any
locks associated with it. Similarly, cifs.ko frees and wakes up any
lock and lock waiter when closing the file:
cifs_close()
cifsFileInfo_put(file->private_data)
/*
* Delete any outstanding lock records. We'll lose them when the file
* is closed anyway.
*/
down_write(&cifsi->lock_sem);
list_for_each_entry_safe(li, tmp, &cifs_file->llist->locks, llist) {
list_del(&li->llist);
cifs_del_lock_waiters(li);
kfree(li);
}
list_del(&cifs_file->llist->llist);
kfree(cifs_file->llist);
up_write(&cifsi->lock_sem);
So we can safely ignore unlocking failures in cifs_lock() if they
happen with the FL_CLOSE flag hint set as both the server and the
client take care of it during the actual closing.
This is not a proper fix for the unlocking failure but it's safe and
it seems to prevent the lock leakages and crashes the customer
experiences.
Signed-off-by: Aurelien Aptel <aaptel@suse.com> Signed-off-by: NeilBrown <neil@brown.name> Signed-off-by: Steve French <stfrench@microsoft.com> Acked-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In half-duplex operation, RX should be started after TX completes.
If DMA is used, there is a case when the DMA transfer completes but the
TX FIFO is not emptied, so the RX cannot be restarted just yet.
Use a boolean variable to store this state and rearm TX interrupt mask
to be signaled again that the transfer finished. In interrupt transmit
handler this variable is used to start RX. A warning message is generated
if RX is activated before TX fifo is cleared.
Fixes: b389f173aaa1 ("tty/serial: atmel: RS485 half duplex w/DMA: enable
RX after TX is done") Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com> Acked-by: Richard Genoud <richard.genoud@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently, we are releasing the indirect buffer where we are done with
it in ext4_ind_remove_space(), so we can see the brelse() and
BUFFER_TRACE() everywhere. It seems fragile and hard to read, and we
may probably forget to release the buffer some day. This patch cleans
up the code by putting of the code which releases the buffers to the
end of the function.
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Jari Ruusu <jari.ruusu@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
FAR_EL1 is UNKNOWN for all debug exceptions other than those caused by
taking a hardware watchpoint. Unfortunately, if a debug handler returns
a non-zero value, then we will propagate the UNKNOWN FAR value to
userspace via the si_addr field of the SIGTRAP siginfo_t.
Instead, let's set si_addr to take on the PC of the faulting instruction,
which we have available in the current pt_regs.
Cc: <stable@vger.kernel.org> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When kzalloc() fails in push_stack(), free_verifier_state() will free
current verifier state. As push_stack() returns, dst_reg was restored
if ptr_is_dst_reg is false. However, as member of the cur_state,
dst_reg is also freed, and error occurs when dereferencing dst_reg.
Simply fix it by testing ret of push_stack() before restoring dst_reg.
Fixes: 979d63d50c0c ("bpf: prevent out of bounds speculation on pointer arithmetic") Signed-off-by: Xu Yu <xuyu@linux.alibaba.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When MPOL_MF_STRICT was specified and an existing page was already on a
node that does not follow the policy, mbind() should return -EIO. But
commit 6f4576e3687b ("mempolicy: apply page table walker on
queue_pages_range()") broke the rule.
And commit c8633798497c ("mm: mempolicy: mbind and migrate_pages support
thp migration") didn't return the correct value for THP mbind() too.
If MPOL_MF_STRICT is set, ignore vma_migratable() to make sure it
reaches queue_pages_to_pte_range() or queue_pages_pmd() to check if an
existing page was already on a node that does not follow the policy.
And, non-migratable vma may be used, return -EIO too if MPOL_MF_MOVE or
MPOL_MF_MOVE_ALL was specified.
Tested with https://github.com/metan-ucw/ltp/blob/master/testcases/kernel/syscalls/mbind/mbind02.c
[akpm@linux-foundation.org: tweak code comment] Link: http://lkml.kernel.org/r/1553020556-38583-1-git-send-email-yang.shi@linux.alibaba.com Fixes: 6f4576e3687b ("mempolicy: apply page table walker on queue_pages_range()") Signed-off-by: Yang Shi <yang.shi@linux.alibaba.com> Signed-off-by: Oscar Salvador <osalvador@suse.de> Reported-by: Cyril Hrubis <chrubis@suse.cz> Suggested-by: Kirill A. Shutemov <kirill@shutemov.name> Acked-by: Rafael Aquini <aquini@redhat.com> Reviewed-by: Oscar Salvador <osalvador@suse.de> Acked-by: David Rientjes <rientjes@google.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
IOMMUs using ARMv7 short-descriptor format require page tables (level 1
and 2) to be allocated within the first 4GB of RAM, even on 64-bit
systems.
For level 1/2 pages, ensure GFP_DMA32 is used if CONFIG_ZONE_DMA32 is
defined (e.g. on arm64 platforms).
For level 2 pages, allocate a slab cache in SLAB_CACHE_DMA32. Note that
we do not explicitly pass GFP_DMA[32] to kmem_cache_zalloc, as this is
not strictly necessary, and would cause a warning in mm/sl*b.c, as we
did not update GFP_SLAB_BUG_MASK.
Also, print an error when the physical address does not fit in
32-bit, to make debugging easier in the future.
Link: http://lkml.kernel.org/r/20181210011504.122604-3-drinkcat@chromium.org Fixes: ad67f5a6545f ("arm64: replace ZONE_DMA with ZONE_DMA32") Signed-off-by: Nicolas Boichat <drinkcat@chromium.org> Acked-by: Will Deacon <will.deacon@arm.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Christoph Lameter <cl@linux.com> Cc: David Rientjes <rientjes@google.com> Cc: Hsin-Yi Wang <hsinyi@chromium.org> Cc: Huaisheng Ye <yehs1@lenovo.com> Cc: Joerg Roedel <joro@8bytes.org> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Michal Hocko <mhocko@suse.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Sasha Levin <Alexander.Levin@microsoft.com> Cc: Tomasz Figa <tfiga@google.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Yingjoe Chen <yingjoe.chen@mediatek.com> Cc: Yong Wu <yong.wu@mediatek.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Patch series "iommu/io-pgtable-arm-v7s: Use DMA32 zone for page tables",
v6.
This is a followup to the discussion in [1], [2].
IOMMUs using ARMv7 short-descriptor format require page tables (level 1
and 2) to be allocated within the first 4GB of RAM, even on 64-bit
systems.
For L1 tables that are bigger than a page, we can just use
__get_free_pages with GFP_DMA32 (on arm64 systems only, arm would still
use GFP_DMA).
For L2 tables that only take 1KB, it would be a waste to allocate a full
page, so we considered 3 approaches:
1. This series, adding support for GFP_DMA32 slab caches.
2. genalloc, which requires pre-allocating the maximum number of L2 page
tables (4096, so 4MB of memory).
3. page_frag, which is not very memory-efficient as it is unable to reuse
freed fragments until the whole page is freed. [3]
This series is the most memory-efficient approach.
stable@ note:
We confirmed that this is a regression, and IOMMU errors happen on 4.19
and linux-next/master on MT8173 (elm, Acer Chromebook R13). The issue
most likely starts from commit ad67f5a6545f ("arm64: replace ZONE_DMA
with ZONE_DMA32"), i.e. 4.15, and presumably breaks a number of Mediatek
platforms (and maybe others?).
IOMMUs using ARMv7 short-descriptor format require page tables to be
allocated within the first 4GB of RAM, even on 64-bit systems. On arm64,
this is done by passing GFP_DMA32 flag to memory allocation functions.
For IOMMU L2 tables that only take 1KB, it would be a waste to allocate
a full page using get_free_pages, so we considered 3 approaches:
1. This patch, adding support for GFP_DMA32 slab caches.
2. genalloc, which requires pre-allocating the maximum number of L2
page tables (4096, so 4MB of memory).
3. page_frag, which is not very memory-efficient as it is unable
to reuse freed fragments until the whole page is freed.
This change makes it possible to create a custom cache in DMA32 zone using
kmem_cache_create, then allocate memory using kmem_cache_alloc.
We do not create a DMA32 kmalloc cache array, as there are currently no
users of kmalloc(..., GFP_DMA32). These calls will continue to trigger a
warning, as we keep GFP_DMA32 in GFP_SLAB_BUG_MASK.
This implies that calls to kmem_cache_*alloc on a SLAB_CACHE_DMA32
kmem_cache must _not_ use GFP_DMA32 (it is anyway redundant and
unnecessary).
Link: http://lkml.kernel.org/r/20181210011504.122604-2-drinkcat@chromium.org Signed-off-by: Nicolas Boichat <drinkcat@chromium.org> Acked-by: Vlastimil Babka <vbabka@suse.cz> Acked-by: Will Deacon <will.deacon@arm.com> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Joerg Roedel <joro@8bytes.org> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Sasha Levin <Alexander.Levin@microsoft.com> Cc: Huaisheng Ye <yehs1@lenovo.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Yong Wu <yong.wu@mediatek.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: Tomasz Figa <tfiga@google.com> Cc: Yingjoe Chen <yingjoe.chen@mediatek.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Matthew Wilcox <willy@infradead.org> Cc: Hsin-Yi Wang <hsinyi@chromium.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect
change or polling state is detected") was intended to prevent ports that
were still link training from being forced to U3 suspend state mid
enumeration.
This solved enumeration issues for devices with slow link training.
Turns out some devices are stuck in the link training/polling state,
and thus that patch will prevent suspend completely for these devices.
This is seen with USB3 card readers in some MacBooks.
Instead of preventing suspend, give some time to complete the link
training. On successful training the port will end up as connected
and enabled.
If port instead is stuck in link training the bus suspend will continue
suspending after 360ms (10 * 36ms) timeout (tPollingLFPSTimeout).
Original patch was sent to stable, this one should go there as well
Fixes: 2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected") Cc: stable@vger.kernel.org Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When MI_FLUSH_DW post write hw status page in index mode, the index
value is in dword step and turned into address offset in cmd dword1.
As status page size is 4K, so can't exceed that.
This fixed upper bound check in cmd parser code which incorrectly
stopped VM for reason of invalid MI_FLUSH_DW write index.
v2:
- Fix upper bound as 4K page size because index value is address offset.
Fixes: be1da7070aea ("drm/i915/gvt: vGPU command scanner") Cc: stable@vger.kernel.org # v4.10+ Cc: "Zhao, Yan Y" <yan.y.zhao@intel.com> Reviewed-by: Yan Zhao <yan.y.zhao@intel.com> Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
NV12 framebuffers produced by the VPU shows distorted on RK3288
after win has been disabled when scaling is active.
This issue can be reproduced using a 1080p modeset by:
- Scale a 1280x720 NV12 framebuffer to 1920x1080 on win0
- Disable win0
- Display a 1920x1080 NV12 framebuffer without scaling on win0
- Output will now show the framebuffer distorted
And by:
- Scale a 1280x720 NV12 framebuffer to 1920x1080
- Change to a 720p modeset (win gets disabled and scaling reset to none)
- Output will now show the framebuffer distorted
Fix this by setting scale mode to none when win is disabled.
Marc Zyngier [Tue, 20 Feb 2018 13:01:19 +0000 (13:01 +0000)]
drm/rockchip: Do not use memcpy for MMIO addresses
BugLink: https://bugs.launchpad.net/bugs/1838116
memcpy is only meant to be used for memory, and only that.
MMIO accessors should be used to access MMIO regions, preferably
the ones that correspond to the size of the register accessed.
Let's convert the bulk register copy to writel/readl_relaxed,
which is the correct API.
Some Acer AIO desktops like Veriton Z6860G, Z4860G and Z4660G cannot
record sound from headset MIC. This patch adds the
ALC286_FIXUP_ACER_AIO_HEADSET_MIC quirk to fix this issue.
Fixes: 9f8aefed9623 ("ALSA: hda/realtek: Fix mic issue on Acer AIO Veriton Z4660G") Fixes: b72f936f6b32 ("ALSA: hda/realtek: Fix mic issue on Acer AIO Veriton Z4860G/Z6860G") Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Reviewed-by: Kailang Yang <kailang@realtek.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If the last NFSv3 unmount from a given host races with a mount from the
same host, we can destroy an nlm_host that is still in use.
Specifically nlmclnt_lookup_host() can increment h_count on
an nlm_host that nlmclnt_release_host() has just successfully called
refcount_dec_and_test() on.
Once nlmclnt_lookup_host() drops the mutex, nlm_destroy_host_lock()
will be called to destroy the nlmclnt which is now in use again.
The cause of the problem is that the dec_and_test happens outside the
locked region. This is easily fixed by using
refcount_dec_and_mutex_lock().
Back in commit a89ca6f24ffe4 ("Btrfs: fix fsync after truncate when
no_holes feature is enabled") I added an assertion that is triggered when
an inline extent is found to assert that the length of the (uncompressed)
data the extent represents is the same as the i_size of the inode, since
that is true most of the time I couldn't find or didn't remembered about
any exception at that time. Later on the assertion was expanded twice to
deal with a case of a compressed inline extent representing a range that
matches the sector size followed by an expanding truncate, and another
case where fallocate can update the i_size of the inode without adding
or updating existing extents (if the fallocate range falls entirely within
the first block of the file). These two expansion/fixes of the assertion
were done by commit 7ed586d0a8241 ("Btrfs: fix assertion on fsync of
regular file when using no-holes feature") and commit 6399fb5a0b69a
("Btrfs: fix assertion failure during fsync in no-holes mode").
These however missed the case where an falloc expands the i_size of an
inode to exactly the sector size and inline extent exists, for example:
$ mkfs.btrfs -f -O no-holes /dev/sdc
$ mount /dev/sdc /mnt
$ xfs_io -f -c "pwrite -S 0xab 0 1096" /mnt/foobar
wrote 1096/1096 bytes at offset 0
1 KiB, 1 ops; 0.0002 sec (4.448 MiB/sec and 4255.3191 ops/sec)
Updating the assertion again to allow for this particular case would result
in a meaningless assertion, plus there is currently no risk of logging
content that would result in any corruption after a log replay if the size
of the data encoded in an inline extent is greater than the inode's i_size
(which is not currently possibe either with or without compression),
therefore just remove the assertion.
CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Similarly to commit a7603ac1fc8c ("geneve: change NET_UDP_TUNNEL
dependency to select"), GTP has a dependency on NET_UDP_TUNNEL which
makes impossible to compile it if no other protocol depending on
NET_UDP_TUNNEL is selected.
Fix this by changing the depends to a select, and drop NET_IP_TUNNEL from
the select list, as it already depends on NET_UDP_TUNNEL.
Signed-off-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When excuting a command like:
modprobe ipmi_si ports=0xffc0e3 type=bt
The system would get an oops.
The trouble here is that ipmi_si_hardcode_find_bmc() is called before
ipmi_si_platform_init(), but initialization of the hard-coded device
creates an IPMI platform device, which won't be initialized yet.
The real trouble is that hard-coded devices aren't created with
any device, and the fixup is done later. So do it right, create the
hard-coded devices as normal platform devices.
This required adding some new resource types to the IPMI platform
code for passing information required by the hard-coded device
and adding some code to remove the hard-coded platform devices
on module removal.
To enforce the "hard-coded devices passed by the user take priority
over firmware devices" rule, some special code was added to check
and see if a hard-coded device already exists.
The backport required some minor fixups and adding the device
id table that had been added in another change and was used
in this one.
When we get an interrupt for a channel program, it is not
necessarily the final interrupt; for example, the issuing
guest may request an intermediate interrupt by specifying
the program-controlled-interrupt flag on a ccw.
We must not switch the state to idle if the interrupt is not
yet final; even more importantly, we must not free the translated
channel program if the interrupt is not yet final, or the host
can crash during cp rewind.
The CPUID flag ARCH_CAPABILITIES is unconditioinally exposed to host
userspace for all x86 hosts, i.e. KVM advertises ARCH_CAPABILITIES
regardless of hardware support under the pretense that KVM fully
emulates MSR_IA32_ARCH_CAPABILITIES. Unfortunately, only VMX hosts
handle accesses to MSR_IA32_ARCH_CAPABILITIES (despite KVM_GET_MSRS
also reporting MSR_IA32_ARCH_CAPABILITIES for all hosts).
Move the MSR_IA32_ARCH_CAPABILITIES handling to common x86 code so
that it's emulated on AMD hosts.
Fixes: 1eaafe91a0df4 ("kvm: x86: IA32_ARCH_CAPABILITIES is always supported") Cc: stable@vger.kernel.org Reported-by: Xiaoyao Li <xiaoyao.li@linux.intel.com> Cc: Jim Mattson <jmattson@google.com> Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
KVM's API requires thats ioctls must be issued from the same process
that created the VM. In other words, userspace can play games with a
VM's file descriptors, e.g. fork(), SCM_RIGHTS, etc..., but only the
creator can do anything useful. Explicitly reject device ioctls that
are issued by a process other than the VM's creator, and update KVM's
API documentation to extend its requirements to device ioctls.
Fixes: 852b6d57dc7f ("kvm: add device control API") Cc: <stable@vger.kernel.org> Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The SMT disable 'nosmt' command line argument is not working properly when
CONFIG_HOTPLUG_CPU is disabled. The teardown of the sibling CPUs which are
required to be brought up due to the MCE issues, cannot work. The CPUs are
then kept in a half dead state.
As the 'nosmt' functionality has become popular due to the speculative
hardware vulnerabilities, the half torn down state is not a proper solution
to the problem.
Enforce CONFIG_HOTPLUG_CPU=y when SMP is enabled so the full operation is
possible.
Reported-by: Tianyu Lan <Tianyu.Lan@microsoft.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Konrad Wilk <konrad.wilk@oracle.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Mukesh Ojha <mojha@codeaurora.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Rik van Riel <riel@surriel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Micheal Kelley <michael.h.kelley@microsoft.com> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Borislav Petkov <bp@alien8.de> Cc: K. Y. Srinivasan <kys@microsoft.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20190326163811.598166056@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Tianyu reported a crash in a CPU hotplug teardown callback when booting a
kernel which has CONFIG_HOTPLUG_CPU disabled with the 'nosmt' boot
parameter.
It turns out that the SMP=y CONFIG_HOTPLUG_CPU=n case has been broken
forever in case that a bringup callback fails. Unfortunately this issue was
not recognized when the CPU hotplug code was reworked, so the shortcoming
just stayed in place.
When a bringup callback fails, the CPU hotplug code rolls back the
operation and takes the CPU offline.
The 'nosmt' command line argument uses a bringup failure to abort the
bringup of SMT sibling CPUs. This partial bringup is required due to the
MCE misdesign on Intel CPUs.
With CONFIG_HOTPLUG_CPU=y the rollback works perfectly fine, but
CONFIG_HOTPLUG_CPU=n lacks essential mechanisms to exercise the low level
teardown of a CPU including the synchronizations in various facilities like
RCU, NOHZ and others.
As a consequence the teardown callbacks which must be executed on the
outgoing CPU within stop machine with interrupts disabled are executed on
the control CPU in interrupt enabled and preemptible context causing the
kernel to crash and burn. The pre state machine code has a different
failure mode which is more subtle and resulting in a less obvious use after
free crash because the control side frees resources which are still in use
by the undead CPU.
But this is not a x86 only problem. Any architecture which supports the
SMP=y HOTPLUG_CPU=n combination suffers from the same issue. It's just less
likely to be triggered because in 99.99999% of the cases all bringup
callbacks succeed.
The easy solution of making HOTPLUG_CPU mandatory for SMP is not working on
all architectures as the following architectures have either no hotplug
support at all or not all subarchitectures support it:
Crashing the kernel in such a situation is not an acceptable state
either.
Implement a minimal rollback variant by limiting the teardown to the point
where all regular teardown callbacks have been invoked and leave the CPU in
the 'dead' idle state. This has the following consequences:
- the CPU is brought down to the point where the stop_machine takedown
would happen.
- the CPU stays there forever and is idle
- The CPU is cleared in the CPU active mask, but not in the CPU online
mask which is a legit state.
- Interrupts are not forced away from the CPU
- All facilities which only look at online mask would still see it, but
that is the case during normal hotplug/unplug operations as well. It's
just a (way) longer time frame.
This will expose issues, which haven't been exposed before or only seldom,
because now the normally transient state of being non active but online is
a permanent state. In testing this exposed already an issue vs. work queues
where the vmstat code schedules work on the almost dead CPU which ends up
in an unbound workqueue and triggers 'preemtible context' warnings. This is
not a problem of this change, it merily exposes an already existing issue.
Still this is better than crashing fully without a chance to debug it.
This is mainly thought as workaround for those architectures which do not
support HOTPLUG_CPU. All others should enforce HOTPLUG_CPU for SMP.
Fixes: 2e1a3483ce74 ("cpu/hotplug: Split out the state walk into functions") Reported-by: Tianyu Lan <Tianyu.Lan@microsoft.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Tianyu Lan <Tianyu.Lan@microsoft.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Konrad Wilk <konrad.wilk@oracle.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Mukesh Ojha <mojha@codeaurora.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Rik van Riel <riel@surriel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Micheal Kelley <michael.h.kelley@microsoft.com> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Borislav Petkov <bp@alien8.de> Cc: K. Y. Srinivasan <kys@microsoft.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20190326163811.503390616@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A TSC packet can slip past MTC packets so that the timestamp appears to
go backwards. One estimate is that can be up to about 40 CPU cycles,
which is certainly less than 0x1000 TSC ticks, but accept slippage an
order of magnitude more to be on the safe side.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: stable@vger.kernel.org Fixes: 79b58424b821c ("perf tools: Add Intel PT support for decoding MTC packets") Link: http://lkml.kernel.org/r/20190325135135.18348-1-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Our MIPS 1004Kc SoCs were seeing random userspace crashes with SIGILL
and SIGSEGV that could not be traced back to a userspace code bug. They
had all the magic signs of an I/D cache coherency issue.
Now recently we noticed that the /proc/sys/vm/compact_memory interface
was quite efficient at provoking this class of userspace crashes.
Studying the code in mm/migrate.c there is a distinction made between
migrating a page that is mapped at the instant of migration and one that
is not mapped. Our problem turned out to be the non-mapped pages.
For the non-mapped page the code performs a copy of the page content and
all relevant meta-data of the page without doing the required D-cache
maintenance. This leaves dirty data in the D-cache of the CPU and on
the 1004K cores this data is not visible to the I-cache. A subsequent
page-fault that triggers a mapping of the page will happily serve the
process with potentially stale code.
What about ARM then, this bug should have seen greater exposure? Well
ARM became immune to this flaw back in 2010, see commit c01778001a4f
("ARM: 6379/1: Assume new page cache pages have dirty D-cache").
My proposed fix moves the D-cache maintenance inside move_to_new_page to
make it common for both cases.
Link: http://lkml.kernel.org/r/20190315083502.11849-1-larper@axis.com Fixes: 97ee0524614 ("flush cache before installing new page at migraton") Signed-off-by: Lars Persson <larper@axis.com> Reviewed-by: Paul Burton <paul.burton@mips.com> Acked-by: Mel Gorman <mgorman@techsingularity.net> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When the kernel is compiled with preemption enabled, the URB completion
handler can run in parallel with the work responsible for waking up the
tty layer. If the URB handler sets the EVENT_TTY_WAKEUP bit during the
call to tty_port_tty_wakeup() to signal that there is room for additional
input, it will be cleared at the end of this call. As a result, TX traffic
on the upper layer will be blocked.
This can be seen with a kernel configured with CONFIG_PREEMPT, and a fast
modem connected with PPP running over a USB CDC-ACM port.
Use test_and_clear_bit() instead, which ensures that each wakeup requested
by the URB completion code will trigger a call to tty_port_tty_wakeup().
A suspended SS port in U3 link state will go to U0 when resumed, but
can almost immediately after that enter U1 or U2 link power save
states before host controller driver reads the port status.
Host controller driver only checks for U0 state, and might miss
the finished resume, leaving flags unclear and skip notifying usb
code of the wake.
Add U1 and U2 to the possible link states when checking for finished
port resume.
When plugging BUFFALO LUA4-U3-AGT USB3.0 to Gigabit Ethernet LAN
Adapter, warning messages filled up dmesg.
[ 101.098287] xhci-hcd ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?
[ 101.117463] xhci-hcd ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?
[ 101.136513] xhci-hcd ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?
Adding the XHCI_TRUST_TX_LENGTH quirk resolves the issue.
There are cases where multiple device tree nodes point to the
same phy node by means of the "phys" property, but we should
only consider those nodes that are marked as available rather
than just any node.
Fixes: 98bfb3946695 ("usb: of: add an api to get dr_mode by the phy node") Cc: stable@vger.kernel.org # v4.4+ Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In f_hidg_write() the write_spinlock is acquired before calling
usb_ep_queue() which causes a deadlock when dummy_hcd is being used.
This is because dummy_queue() callbacks into f_hidg_req_complete() which
tries to acquire the same spinlock. This is (part of) the backtrace when
the deadlock occurs:
0xffffffffc06b1410 in f_hidg_req_complete
0xffffffffc06a590a in usb_gadget_giveback_request
0xffffffffc06cfff2 in dummy_queue
0xffffffffc06a4b96 in usb_ep_queue
0xffffffffc06b1eb6 in f_hidg_write
0xffffffff8127730b in __vfs_write
0xffffffff812774d1 in vfs_write
0xffffffff81277725 in SYSC_write
Fix this by releasing the write_spinlock before calling usb_ep_queue()
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com> Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: stable@vger.kernel.org # 4.11+ Fixes: 749494b6bdbb ("usb: gadget: f_hid: fix: Move IN request allocation to set_alt()") Signed-off-by: Radoslav Gerganov <rgerganov@vmware.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
While only the first PHY supports mode switching, the remaining PHYs
work in USB host mode. They should support set_mode with mode=USB_HOST
instead of failing. This is especially needed now that the USB core does
set_mode for all USB ports, which was added in commit b97a31348379 ("usb:
core: comply to PHY framework").
Make set_mode with mode=USB_HOST a no-op instead of failing for the
non-OTG USB PHYs.
Fixes: 6ba43c291961 ("phy-sun4i-usb: Add support for phy_set_mode") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Current code test wrong value so it does not verify if the written
data is correctly read back. Fix it.
Also make it return -EPERM if read value does not match written bit,
just like it done for adnp_gpio_direction_output().
If drm_gem_handle_create() fails in vgem_gem_create(), then the
drm_vgem_gem_object is freed twice: once when the reference is dropped
by drm_gem_object_put_unlocked(), and again by __vgem_gem_destroy().
This was hit by syzkaller using fault injection.
Fix it by skipping the second free.
Reported-by: syzbot+e73f2fb5ed5a5df36d33@syzkaller.appspotmail.com Fixes: af33a9190d02 ("drm/vgem: Enable dmabuf import interfaces") Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Laura Abbott <labbott@redhat.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: stable@vger.kernel.org Signed-off-by: Eric Biggers <ebiggers@google.com> Acked-by: Laura Abbott <labbott@redhat.com> Signed-off-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190226214451.195123-1-ebiggers@kernel.org Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A new dir entry can be created in get_subdir and its 'header->parent' is
set to NULL. Only after insert_header success, it will be set to 'dir',
otherwise 'header->parent' is set to NULL and drop_sysctl_table is called.
However in err handling path of get_subdir, drop_sysctl_table also be
called on 'new->header' regardless its value of parent pointer. Then
put_links is called, which triggers NULL-ptr deref when access member of
header->parent.
In fact we have multiple error paths which call drop_sysctl_table() there,
upon failure on insert_links() we also call drop_sysctl_table().And even
in the successful case on __register_sysctl_table() we still always call
drop_sysctl_table().This patch fix it.
Link: http://lkml.kernel.org/r/20190314085527.13244-1-yuehaibing@huawei.com Fixes: 0e47c99d7fe25 ("sysctl: Replace root_list with links between sysctl_table_sets") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reported-by: Hulk Robot <hulkci@huawei.com> Acked-by: Luis Chamberlain <mcgrof@kernel.org> Cc: Kees Cook <keescook@chromium.org> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: <stable@vger.kernel.org> [3.4+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The Quectel EM12 is a Cat. 12 LTE modem. It behaves in the exactly the
same way as the EP06 (including the dynamic configuration behavior), so
the same checks on reserved interfaces, etc. are needed.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The SIMCom SIM5218 and compatible devices have 5 USB interfaces, only 4
of which are serial ports. The fifth is a network interface supported
by the qmi-wwan driver. Furthermore, the serial ports do not support
modem control signals. Add driver_info flags to reflect this.
The write_parport_reg_nonblock() helper takes a reference to the struct
mos_parport, but failed to release it in a couple of error paths after
allocation failures, leading to a memory leak.
Johan said that move the kref_get() and mos_parport assignment to the
end of urbtrack initialisation is a better way, so move it. and
mos_parport do not used until urbtrack initialisation.
Signed-off-by: Lin Yi <teroincn@163.com> Fixes: b69578df7e98 ("USB: usbserial: mos7720: add support for parallel port on moschip 7715") Cc: stable <stable@vger.kernel.org> # 2.6.35 Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Lorenz Messtechnik has a device that is controlled by the cp210x driver,
so add the device id to the driver. The device id was provided by
Silicon-Labs for the devices from this vendor.
We disable transmission interrupt (clear SCSCR_TIE) after all data has been transmitted
(if uart_circ_empty(xmit)). While transmitting, if the data is still in the tty buffer,
re-enable the SCSCR_TIE bit, which was done at sci_start_tx().
This is unnecessary processing, wasting CPU operation if the data transmission length is large.
And further, transmit end, FIFO empty bits disabling have also been performed in the step above.
Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
`ni_cdio_cmdtest()` validates Comedi asynchronous commands for the DIO
subdevice (subdevice 2) of supported National Instruments M-series
cards. It is called when handling the `COMEDI_CMD` and `COMEDI_CMDTEST`
ioctls for this subdevice. There are two causes for a possible
divide-by-zero error when validating that the `stop_arg` member of the
passed-in command is not too large.
The first cause for the divide-by-zero is that calls to
`comedi_bytes_per_scan()` are only valid once the command has been
copied to `s->async->cmd`, but that copy is only done for the
`COMEDI_CMD` ioctl. For the `COMEDI_CMDTEST` ioctl, it will use
whatever was left there by the previous `COMEDI_CMD` ioctl, if any.
(This is very likely, as it is usual for the application to use
`COMEDI_CMDTEST` before `COMEDI_CMD`.) If there has been no previous,
valid `COMEDI_CMD` for this subdevice, then `comedi_bytes_per_scan()`
will return 0, so the subsequent division in `ni_cdio_cmdtest()` of
`s->async->prealloc_bufsz / comedi_bytes_per_scan(s)` will be a
divide-by-zero error. To fix this error, call a new function
`comedi_bytes_per_scan_cmd(s, cmd)`, based on the existing
`comedi_bytes_per_scan(s)` but using a specified `struct comedi_cmd` for
its calculations. (Also refactor `comedi_bytes_per_scan()` to call the
new function.)
Once the first cause for the divide-by-zero has been fixed, the second
cause is that `comedi_bytes_per_scan_cmd()` can legitimately return 0 if
the `scan_end_arg` member of the `struct comedi_cmd` being tested is 0.
Fix it by only performing the division (and validating that `stop_arg`
is no more than the maximum value) if `comedi_bytes_per_scan_cmd()`
returns a non-zero value.
The problem was reported on the COMEDI mailing list here:
https://groups.google.com/forum/#!topic/comedi_list/4t9WlHzMhKM
Reported-by: Ivan Vasilyev <grabesstimme@gmail.com> Tested-by: Ivan Vasilyev <grabesstimme@gmail.com> Fixes: f164cbf98fa8 ("staging: comedi: ni_mio_common: add finite regeneration to dio output") Cc: <stable@vger.kernel.org> # 4.6+ Cc: Spencer E. Olson <olsonse@umich.edu> Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Suppose more than one non-NPIV FCP device is active on the same channel.
Send I/O to storage and have some of the pending I/O run into a SCSI
command timeout, e.g. due to bit errors on the fibre. Now the error
situation stops. However, we saw FCP requests continue to timeout in the
channel. The abort will be successful, but the subsequent TUR fails.
Scsi_eh starts. The LUN reset fails. The target reset fails. The host
reset only did an FCP device recovery. However, for non-NPIV FCP devices,
this does not close and reopen ports on the SAN-side if other non-NPIV FCP
device(s) share the same open ports.
In order to resolve the continuing FCP request timeouts, we need to
explicitly close and reopen ports on the SAN-side.
This was missing since the beginning of zfcp in v2.6.0 history commit ea127f975424 ("[PATCH] s390 (7/7): zfcp host adapter.").
Note: The FSF requests for forced port reopen could run into FSF request
timeouts due to other reasons. This would trigger an internal FCP device
recovery. Pending forced port reopen recoveries would get dismissed. So
some ports might not get fully reopened during this host reset handler.
However, subsequent I/O would trigger the above described escalation and
eventually all ports would be forced reopen to resolve any continuing FCP
request timeouts due to earlier bit errors.
Signed-off-by: Steffen Maier <maier@linux.ibm.com> Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: <stable@vger.kernel.org> #3.0+ Reviewed-by: Jens Remus <jremus@linux.ibm.com> Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
An already deleted SCSI device can exist on the Scsi_Host and remain there
because something still holds a reference. A new SCSI device with the same
H:C:T:L and FCP device, target port WWPN, and FCP LUN can be created. When
we try to unblock an rport, we still find the deleted SCSI device and
return early because the zfcp_scsi_dev of that SCSI device is not
ZFCP_STATUS_COMMON_UNBLOCKED. Hence we miss to unblock the rport, even if
the new proper SCSI device would be in good state.
Therefore, skip deleted SCSI devices when iterating the sdevs of the shost.
[cf. __scsi_device_lookup{_by_target}() or scsi_device_get()]
The following abbreviated trace sequence can indicate such problem:
Area : REC
Tag : ersfs_3
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x40000000 not ZFCP_STATUS_COMMON_UNBLOCKED
Ready count : n not incremented yet
Running count : 0x00000000
ERP want : 0x01
ERP need : 0xc1 ZFCP_ERP_ACTION_NONE
Area : REC
Tag : ersfs_3
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x41000000
Ready count : n+1
Running count : 0x00000000
ERP want : 0x01
ERP need : 0x01
...
Area : REC
Level : 4 only with increased trace level
Tag : ertru_l
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x40000000
Request ID : 0x0000000000000000
ERP status : 0x01800000
ERP step : 0x1000
ERP action : 0x01
ERP count : 0x00
NOT followed by a trace record with tag "scpaddy"
for WWPN 0x50050763031bd327.
Signed-off-by: Steffen Maier <maier@linux.ibm.com> Fixes: 6f2ce1c6af37 ("scsi: zfcp: fix rport unblock race with LUN recovery") Cc: <stable@vger.kernel.org> #2.6.32+ Reviewed-by: Jens Remus <jremus@linux.ibm.com> Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
projects / mirror_ubuntu-bionic-kernel.git / log