MPLS does not support nexthops with an MPLS address family.
Specifically, it does not handle RTA_GATEWAY attribute. Make it
clear by returning an error.
Fixes: 03c0566542f4c ("mpls: Netlink commands to add, remove, and dump routes") Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
IPv6 currently does not support nexthops outside of the AF_INET6 family.
Specifically, it does not handle RTA_VIA attribute. If it is passed
in a route add request, the actual route added only uses the device
which is clearly not what the user intended:
$ ip -6 ro add 2001:db8:2::/64 via inet 172.16.1.1 dev eth0
$ ip ro ls
...
2001:db8:2::/64 dev eth0 metric 1024 pref medium
Catch this and fail the route add:
$ ip -6 ro add 2001:db8:2::/64 via inet 172.16.1.1 dev eth0
Error: IPv6 does not support RTA_VIA attribute.
Fixes: 03c0566542f4c ("mpls: Netlink commands to add, remove, and dump routes") Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
IPv4 currently does not support nexthops outside of the AF_INET family.
Specifically, it does not handle RTA_VIA attribute. If it is passed
in a route add request, the actual route added only uses the device
which is clearly not what the user intended:
$ ip ro add 172.16.1.0/24 via inet6 2001:db8:1::1 dev eth0
$ ip ro ls
...
172.16.1.0/24 dev eth0
Catch this and fail the route add:
$ ip ro add 172.16.1.0/24 via inet6 2001:db8:1::1 dev eth0
Error: IPv4 does not support RTA_VIA attribute.
Fixes: 03c0566542f4c ("mpls: Netlink commands to add, remove, and dump routes") Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Extract IP options in cipso_v4_error and use __icmp_send.
Signed-off-by: Sergey Nazarov <s-nazarov@yandex.ru> Acked-by: Paul Moore <paul@paul-moore.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Add __icmp_send function having ip_options struct parameter
Signed-off-by: Sergey Nazarov <s-nazarov@yandex.ru> Reviewed-by: Paul Moore <paul@paul-moore.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Replace set_current_state with __set_current_state since no memory
barrier is needed at this point.
Signed-off-by: Timur Celik <mail@timurcelik.de> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Zero-copy callback flag is not yet set on frag list skb at the moment
xenvif_handle_frag_list() returns -ENOMEM. This eventually results in
leaking grant ref mappings since xenvif_zerocopy_callback() is never
called for these fragments. Those eventually build up and cause Xen
to kill Dom0 as the slots get reused for new mappings:
"d0v0 Attempt to implicitly unmap a granted PTE c010000329fce005"
That behavior is observed under certain workloads where sudden spikes
of page cache writes coexist with active atomic skb allocations from
network traffic. Additionally, rework the logic to deal with frag_list
deallocation in a single place.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com> Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Occasionally, during the disconnection procedure on XenBus which
includes hash cache deinitialization there might be some packets
still in-flight on other processors. Handling of these packets includes
hashing and hash cache population that finally results in hash cache
data structure corruption.
In order to avoid this we prevent hashing of those packets if there
are no queues initialized. In that case RCU protection of queues guards
the hash cache as well.
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com> Reviewed-by: Paul Durrant <paul.durrant@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This patch moves setting of the current state into the loop. Otherwise
the task may end up in a busy wait loop if none of the break conditions
are met.
Signed-off-by: Timur Celik <mail@timurcelik.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When sending multicast messages via blocking socket,
if sending link is congested (tsk->cong_link_cnt is set to 1),
the sending thread will be put into sleeping state. However,
tipc_sk_filter_rcv() is called under socket spin lock but
tipc_wait_for_cond() is not. So, there is no guarantee that
the setting of tsk->cong_link_cnt to 0 in tipc_sk_proto_rcv() in
CPU-1 will be perceived by CPU-0. If that is the case, the sending
thread in CPU-0 after being waken up, will continue to see
tsk->cong_link_cnt as 1 and put the sending thread into sleeping
state again. The sending thread will sleep forever.
This commit fixes it by adding memory barrier to tipc_sk_proto_rcv()
and tipc_wait_for_cond().
Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Signed-off-by: Mao Wenan <maowenan@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When debugging an issue I found implausible values in state->pause.
Reason in that state->pause isn't initialized and later only single
bits are changed. Also the struct itself isn't initialized in
phylink_resolve(). So better initialize state->pause and other
not yet initialized fields.
v2:
- use right function name in subject
v3:
- initialize additional fields
Fixes: 9525ae83959b ("phylink: add phylink infrastructure") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
With Micrel KSZ8061 PHY, the link may occasionally not come up after
Ethernet cable connect. The vendor's (Microchip, former Micrel) errata
sheet 80000688A.pdf descripes the problem and possible workarounds in
detail, see below.
The batch implements workaround 1, which permanently fixes the issue.
DESCRIPTION
Link-up may not occur properly when the Ethernet cable is initially
connected. This issue occurs more commonly when the cable is connected
slowly, but it may occur any time a cable is connected. This issue occurs
in the auto-negotiation circuit, and will not occur if auto-negotiation
is disabled (which requires that the two link partners be set to the
same speed and duplex).
END USER IMPLICATIONS
When this issue occurs, link is not established. Subsequent cable
plug/unplaug cycle will not correct the issue.
WORk AROUND
There are four approaches to work around this issue:
1. This issue can be prevented by setting bit 15 in MMD device address 1,
register 2, prior to connecting the cable or prior to setting the
Restart Auto-negotiation bit in register 0h. The MMD registers are
accessed via the indirect access registers Dh and Eh, or via the Micrel
EthUtil utility as shown here:
. if using the EthUtil utility (usually with a Micrel KSZ8061
Evaluation Board), type the following commands:
> address 1
> mmd 1
> iw 2 b61a
. Alternatively, write the following registers to write to the
indirect MMD register:
Write register Dh, data 0001h
Write register Eh, data 0002h
Write register Dh, data 4001h
Write register Eh, data B61Ah
2. The issue can be avoided by disabling auto-negotiation in the KSZ8061,
either by the strapping option, or by clearing bit 12 in register 0h.
Care must be taken to ensure that the KSZ8061 and the link partner
will link with the same speed and duplex. Note that the KSZ8061
defaults to full-duplex when auto-negotiation is off, but other
devices may default to half-duplex in the event of failed
auto-negotiation.
3. The issue can be avoided by connecting the cable prior to powering-up
or resetting the KSZ8061, and leaving it plugged in thereafter.
4. If the above measures are not taken and the problem occurs, link can
be recovered by setting the Restart Auto-Negotiation bit in
register 0h, or by resetting or power cycling the device. Reset may
be either hardware reset or software reset (register 0h, bit 15).
PLAN
This errata will not be corrected in the future revision.
Fixes: 7ab59dc15e2f ("drivers/net/phy/micrel_phy: Add support for new PHYs") Signed-off-by: Alexander Onnasch <alexander.onnasch@landisgyr.com> Signed-off-by: Rajasingh Thavamani <T.Rajasingh@landisgyr.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
It can be reproduced by following steps:
1. virtio_net NIC is configured with gso/tso on
2. configure nginx as http server with an index file bigger than 1M bytes
3. use tc netem to produce duplicate packets and delay:
tc qdisc add dev eth0 root netem delay 100ms 10ms 30% duplicate 90%
4. continually curl the nginx http server to get index file on client
5. BUG_ON is seen quickly
In __skb_to_sgvec(), the skb->len is not equal to the sum of the skb's
linear data size and nonlinear data size, thus BUG_ON triggered.
Because the skb is cloned and a part of nonlinear data is split off.
Duplicate packet is cloned in netem_enqueue() and may be delayed
some time in qdisc. When qdisc len reached the limit and returns
NET_XMIT_DROP, the skb will be retransmit later in write queue.
the skb will be fragmented by tso_fragment(), the limit size
that depends on cwnd and mss decrease, the skb's nonlinear
data will be split off. The length of the skb cloned by netem
will not be updated. When we use virtio_net NIC and invoke skb_to_sgvec(),
the BUG_ON trigger.
To fix it, netem returns NET_XMIT_SUCCESS to upper stack
when it clones a duplicate packet.
Fixes: 35d889d1 ("sch_netem: fix skb leak in netem_enqueue()") Signed-off-by: Sheng Lan <lansheng@huawei.com> Reported-by: Qin Ji <jiqin.ji@huawei.com> Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There are two array out-of-bounds memory accesses, one in
cipso_v4_map_lvl_valid(), the other in netlbl_bitmap_walk(). Both
errors are embarassingly simple, and the fixes are straightforward.
As a FYI for anyone backporting this patch to kernels prior to v4.8,
you'll want to apply the netlbl_bitmap_walk() patch to
cipso_v4_bitmap_walk() as netlbl_bitmap_walk() doesn't exist before
Linux v4.8.
Reported-by: Jann Horn <jannh@google.com> Fixes: 446fda4f2682 ("[NetLabel]: CIPSOv4 engine") Fixes: 3faa8f982f95 ("netlabel: Move bitmap manipulation functions to the NetLabel core.") Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The switch maintains u64 counters for the number of octets sent and
received. These are kept as two u32's which need to be combined. Fix
the combing, which wrongly worked on u16's.
Fixes: 80c4627b2719 ("dsa: mv88x6xxx: Refactor getting a single statistic") Reported-by: Chris Healy <Chris.Healy@zii.aero> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Incoming packets may have IP header checksum verified by the host.
They may not have IP header checksum computed after coalescing.
This patch re-compute the checksum when necessary, otherwise the
packets may be dropped, because Linux network stack always checks it.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There have been reports of oversize UDP packets being sent to the
driver to be transmitted, causing error conditions. The issue is
likely caused by the dst of the SKB switching between 'lo' with
64K MTU and the hardware device with a smaller MTU. Patches are
being proposed by Mahesh Bandewar <maheshb@google.com> to fix the
issue.
In the meantime, add a quick length check in the driver to prevent
the error. The driver uses the TX packet size as index to look up an
array to setup the TX BD. The array is large enough to support all MTU
sizes supported by the driver. The oversize TX packet causes the
driver to index beyond the array and put garbage values into the
TX BD. Add a simple check to prevent this.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Fix regression bug introduced in
commit 365ad353c256 ("tipc: reduce risk of user starvation during link
congestion")
Only signal -EDESTADDRREQ for RDM/DGRAM if we don't have a cached
sockaddr.
Fixes: 365ad353c256 ("tipc: reduce risk of user starvation during link congestion") Signed-off-by: Erik Hugne <erik.hugne@gmail.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When testing another issue I faced the problem that
mv88e6xxx_port_setup_mac() failed due to DUPLEX_UNKNOWN being passed
as argument to mv88e6xxx_port_set_duplex(). We should handle this case
gracefully and return -EOPNOTSUPP, like e.g. mv88e6xxx_port_set_speed()
is doing it.
Fixes: 7f1ae07b51e8 ("net: dsa: mv88e6xxx: add port duplex setter") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Similar to commit 44f49dd8b5a6 ("ipmr: fix possible race resulting from
improper usage of IP_INC_STATS_BH() in preemptible context."), we cannot
assume preemption is disabled when incrementing the counter and
accessing a per-CPU variable.
Preemption can be enabled when we add a route in process context that
corresponds to packets stored in the unresolved queue, which are then
forwarded using this route [1].
Fix this by using IP6_INC_STATS() which takes care of disabling
preemption on architectures where it is needed.
usb 3-1: new full-speed USB device number 18 using xhci_hcd
usb 3-1: New USB device found, idVendor=0b00, idProduct=3070
usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-1: Product: Ingenico 3070
usb 3-1: Manufacturer: Silicon Labs
usb 3-1: SerialNumber: 0001
Apparently this is a POS terminal with embedded USB-to-Serial converter.
Cc: stable@vger.kernel.org Signed-off-by: Ivan Mironov <mironov.ivan@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The cpufreq_global_kobject is created using kobject_create_and_add()
helper, which assigns the kobj_type as dynamic_kobj_ktype and show/store
routines are set to kobj_attr_show() and kobj_attr_store().
These routines pass struct kobj_attribute as an argument to the
show/store callbacks. But all the cpufreq files created using the
cpufreq_global_kobject expect the argument to be of type struct
attribute. Things work fine currently as no one accesses the "attr"
argument. We may not see issues even if the argument is used, as struct
kobj_attribute has struct attribute as its first element and so they
will both get same address.
But this is logically incorrect and we should rather use struct
kobj_attribute instead of struct global_attr in the cpufreq core and
drivers and the show/store callbacks should take struct kobj_attribute
as argument instead.
This bug is caught using CFI CLANG builds in android kernel which
catches mismatch in function prototypes for such callbacks.
Reported-by: Donghee Han <dh.han@samsung.com> Reported-by: Sangkyu Kim <skwith.kim@samsung.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The switch to the generic dma ops made dma masks mandatory, breaking
devices having them not set. In case of bcm63xx, it broke ethernet with
the following warning when trying to up the device:
hugetlb pages should only be migrated if they are 'active'. The
routines set/clear_page_huge_active() modify the active state of hugetlb
pages.
When a new hugetlb page is allocated at fault time, set_page_huge_active
is called before the page is locked. Therefore, another thread could
race and migrate the page while it is being added to page table by the
fault code. This race is somewhat hard to trigger, but can be seen by
strategically adding udelay to simulate worst case scheduling behavior.
Depending on 'how' the code races, various BUG()s could be triggered.
To address this issue, simply delay the set_page_huge_active call until
after the page is successfully added to the page table.
Hugetlb pages can also be leaked at migration time if the pages are
associated with a file in an explicitly mounted hugetlbfs filesystem.
For example, consider a two node system with 4GB worth of huge pages
available. A program mmaps a 2G file in a hugetlbfs filesystem. It
then migrates the pages associated with the file from one node to
another. When the program exits, huge page counts are as follows:
node0
1024 free_hugepages
1024 nr_hugepages
node1
0 free_hugepages
1024 nr_hugepages
Filesystem Size Used Avail Use% Mounted on
nodev 4.0G 2.0G 2.0G 50% /var/opt/hugepool
That is as expected. 2G of huge pages are taken from the free_hugepages
counts, and 2G is the size of the file in the explicitly mounted
filesystem. If the file is then removed, the counts become:
node0
1024 free_hugepages
1024 nr_hugepages
node1
1024 free_hugepages
1024 nr_hugepages
Filesystem Size Used Avail Use% Mounted on
nodev 4.0G 2.0G 2.0G 50% /var/opt/hugepool
Note that the filesystem still shows 2G of pages used, while there
actually are no huge pages in use. The only way to 'fix' the filesystem
accounting is to unmount the filesystem
If a hugetlb page is associated with an explicitly mounted filesystem,
this information in contained in the page_private field. At migration
time, this information is not preserved. To fix, simply transfer
page_private from old to new page at migration time if necessary.
There is a related race with removing a huge page from a file and
migration. When a huge page is removed from the pagecache, the
page_mapping() field is cleared, yet page_private remains set until the
page is actually freed by free_huge_page(). A page could be migrated
while in this state. However, since page_mapping() is not set the
hugetlbfs specific routine to transfer page_private is not called and we
leak the page count in the filesystem.
To fix that, check for this condition before migrating a huge page. If
the condition is detected, return EBUSY for the page.
The prepare_fb call always happens on new_plane_state.
The drm_atomic_helper_cleanup_planes checks to see if
plane state pointer has changed when deciding to call cleanup_fb on
either the new_plane_state or the old_plane_state.
For a non-async atomic commit the state pointer is swapped, so this
helper calls prepare_fb on the new_plane_state and cleanup_fb on the
old_plane_state. This makes sense, since we want to prepare the
framebuffer we are going to use and cleanup the the framebuffer we are
no longer using.
For the async atomic update helpers this differs. The async atomic
update helpers perform in-place updates on the existing state. They call
drm_atomic_helper_cleanup_planes but the state pointer is not swapped.
This means that prepare_fb is called on the new_plane_state and
cleanup_fb is called on the new_plane_state (not the old).
In the case where old_plane_state->fb == new_plane_state->fb then
there should be no behavioral difference between an async update
and a non-async commit. But there are issues that arise when
old_plane_state->fb != new_plane_state->fb.
The first is that the new_plane_state->fb is immediately cleaned up
after it has been prepared, so we're using a fb that we shouldn't
be.
The second occurs during a sequence of async atomic updates and
non-async regular atomic commits. Suppose there are two framebuffers
being interleaved in a double-buffering scenario, fb1 and fb2:
In case of CQHCI, mrq->cmd may be NULL for data requests (non DCMD).
In such case mmc_should_fail_request is directly dereferencing
mrq->cmd while cmd is NULL.
Fix this by checking for mrq->cmd pointer.
We cannot wait on a completion object in the lpfc_nvme_targetport structure
in the _destroy_targetport() code path because the NVMe/fc transport will
free that structure immediately after the .targetport_delete() callback.
This results in a use-after-free, and a hang if slub_debug=FZPU is enabled.
Fix this by putting the completion on the stack.
Signed-off-by: Ewan D. Milne <emilne@redhat.com> Acked-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We cannot wait on a completion object in the lpfc_nvme_lport structure in
the _destroy_localport() code path because the NVMe/fc transport will free
that structure immediately after the .localport_delete() callback. This
results in a use-after-free, and a hang if slub_debug=FZPU is enabled.
Fix this by putting the completion on the stack.
Signed-off-by: Ewan D. Milne <emilne@redhat.com> Acked-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Although TMDS clock is required for HDMI to properly function,
nobody called clk_prepare_enable(). This fixes reference counting
issues and makes sure clock is running when it needs to be running.
Due to TDMS clock being parent clock for DDC clock, TDMS clock
was turned on/off for each EDID probe, causing spurious failures
for certain HDMI/DVI screens.
Fixes: 9c5681011a0c ("drm/sun4i: Add HDMI support") Signed-off-by: Priit Laes <priit.laes@paf.com>
[Maxime: Moved the TMDS clock enable earlier] Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190122073232.7240-1-plaes@plaes.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Notable cmpxchg() does not provide ordering when it fails, however
wake_q_add() requires ordering in this specific case too. Without this
it would be possible for the concurrent wakeup to not observe our
prior state.
The motivation for this change was lockdep splat like below.
| potentially unexpected fatal signal 11.
| BUG: sleeping function called from invalid context at ../mm/page_alloc.c:4317
| in_atomic(): 1, irqs_disabled(): 0, pid: 57, name: segv
| no locks held by segv/57.
| Preemption disabled at:
| [<8182f17e>] get_signal+0x4a6/0x7c4
| CPU: 0 PID: 57 Comm: segv Not tainted 4.17.0+ #23
|
| Stack Trace:
| arc_unwind_core.constprop.1+0xd0/0xf4
| __might_sleep+0x1f6/0x234
| __get_free_pages+0x174/0xca0
| show_regs+0x22/0x330
| get_signal+0x4ac/0x7c4 # print_fatal_signals() -> preempt_disable()
| do_signal+0x30/0x224
| resume_user_mode_begin+0x90/0xd8
So signal handling core calls show_regs() with preemption disabled but
an ensuing GFP_KERNEL page allocator call is flagged by lockdep.
We could have switched to GFP_NOWAIT, but turns out that is not enough
anways and eliding page allocator call leads to less code and
instruction traces to sift thru when debugging pesky crashes.
FWIW, this patch doesn't cure the lockdep splat (which next patch does).
Reviewed-by: William Kucharski <william.kucharski@oracle.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On large systems with multiple devices of the same class (e.g. NVMe disks,
using managed interrupts), the kernel can affinitize these interrupts to a
small subset of CPUs instead of spreading them out evenly.
irq_matrix_alloc_managed() tries to select the CPU in the supplied cpumask
of possible target CPUs which has the lowest number of interrupt vectors
allocated.
This is done by searching the CPU with the highest number of available
vectors. While this is correct for non-managed CPUs it can select the wrong
CPU for managed interrupts. Under certain constellations this results in
affinitizing the managed interrupts of several devices to a single CPU in
a set.
The book keeping of available vectors works the following way:
1) Non-managed interrupts:
available is decremented when the interrupt is actually requested by
the device driver and a vector is assigned. It's incremented when the
interrupt and the vector are freed.
2) Managed interrupts:
Managed interrupts guarantee vector reservation when the MSI/MSI-X
functionality of a device is enabled, which is achieved by reserving
vectors in the bitmaps of the possible target CPUs. This reservation
decrements the available count on each possible target CPU.
When the interrupt is requested by the device driver then a vector is
allocated from the reserved region. The operation is reversed when the
interrupt is freed by the device driver. Neither of these operations
affect the available count.
The reservation persist up to the point where the MSI/MSI-X
functionality is disabled and only this operation increments the
available count again.
For non-managed interrupts the available count is the correct selection
criterion because the guaranteed reservations need to be taken into
account. Using the allocated counter could lead to a failing allocation in
the following situation (total vector space of 10 assumed):
CPU0 CPU1
available: 2 0
allocated: 5 3 <--- CPU1 is selected, but available space = 0
managed reserved: 3 7
while available yields the correct result.
For managed interrupts the available count is not the appropriate
selection criterion because as explained above the available count is not
affected by the actual vector allocation.
The following example illustrates that. Total vector space of 10
assumed. The starting point is:
Allocating vectors for three non-managed interrupts will result in
affinitizing the first two to CPU0 and the third one to CPU1 because the
available count is adjusted with each allocation:
But the allocation of three managed interrupts starting from the same
point will affinitize all of them to CPU0 because the available count is
not affected by the allocation (see above). So the end result is:
CPU0 CPU1
available: 5 4
allocated: 5 3
Introduce a "managed_allocated" field in struct cpumap to track the vector
allocation for managed interrupts separately. Use this information to
select the target CPU when a vector is allocated for a managed interrupt,
which results in more evenly distributed vector assignments. The above
example results in the following allocations:
The allocation of non-managed interrupts is not affected by this change and
is still evaluating the available count.
The overall distribution of interrupt vectors for both types of interrupts
might still not be perfectly even depending on the number of non-managed
and managed interrupts in a system, but due to the reservation guarantee
for managed interrupts this cannot be avoided.
Expose the new field in debugfs as well.
[ tglx: Clarified the background of the problem in the changelog and
described it independent of NVME ]
Signed-off-by: Long Li <longli@microsoft.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Michael Kelley <mikelley@microsoft.com> Link: https://lkml.kernel.org/r/20181106040000.27316-1-longli@linuxonhyperv.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Linux spreads out the non managed interrupt across the possible target CPUs
to avoid vector space exhaustion.
Managed interrupts are treated differently, as for them the vectors are
reserved (with guarantee) when the interrupt descriptors are initialized.
When the interrupt is requested a real vector is assigned. The assignment
logic uses the first CPU in the affinity mask for assignment. If the
interrupt has more than one CPU in the affinity mask, which happens when a
multi queue device has less queues than CPUs, then doing the same search as
for non managed interrupts makes sense as it puts the interrupt on the
least interrupt plagued CPU. For single CPU affine vectors that's obviously
a NOOP.
Restructre the matrix allocation code so it does the 'best CPU' search, add
the sanity check for an empty affinity mask and adapt the call site in the
x86 vector management code.
[ tglx: Added the empty mask check to the core and improved change log ]
Linux finds the CPU which has the lowest vector allocation count to spread
out the non managed interrupts across the possible target CPUs, but does
not do so for managed interrupts.
Split out the CPU selection code into a helper function for reuse. No
functional change.
When calling __put_user(foo(), ptr), the __put_user() macro would call
foo() in between __uaccess_begin() and __uaccess_end(). If that code
were buggy, then those bugs would be run without SMAP protection.
Fortunately, there seem to be few instances of the problem in the
kernel. Nevertheless, __put_user() should be fixed to avoid doing this.
Therefore, evaluate __put_user()'s argument before setting AC.
This issue was noticed when an objtool hack by Peter Zijlstra complained
about genregs_get() and I compared the assembly output to the C source.
[ bp: Massage commit message and fixed up whitespace. ]
Fixes: 11f1a4b9755f ("x86: reorganize SMAP handling in user space accesses") Signed-off-by: Andy Lutomirski <luto@kernel.org> Signed-off-by: Borislav Petkov <bp@suse.de> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Brian Gerst <brgerst@gmail.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/20190225125231.845656645@infradead.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The MIPS eBPF JIT calls flush_icache_range() in order to ensure the
icache observes the code that we just wrote. Unfortunately it gets the
end address calculation wrong due to some bad pointer arithmetic.
The struct jit_ctx target field is of type pointer to u32, and as such
adding one to it will increment the address being pointed to by 4 bytes.
Therefore in order to find the address of the end of the code we simply
need to add the number of 4 byte instructions emitted, but we mistakenly
add the number of instructions multiplied by 4. This results in the call
to flush_icache_range() operating on a memory region 4x larger than
intended, which is always wasteful and can cause crashes if we overrun
into an unmapped page.
Fix this by correcting the pointer arithmetic to remove the bogus
multiplication, and use braces to remove the need for a set of brackets
whilst also making it obvious that the target field is a pointer.
Signed-off-by: Paul Burton <paul.burton@mips.com> Fixes: b6bd53f9c4e8 ("MIPS: Add missing file for eBPF JIT.") Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Martin KaFai Lau <kafai@fb.com> Cc: Song Liu <songliubraving@fb.com> Cc: Yonghong Song <yhs@fb.com> Cc: netdev@vger.kernel.org Cc: bpf@vger.kernel.org Cc: linux-mips@vger.kernel.org Cc: stable@vger.kernel.org # v4.13+ Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
__cmpxchg_small erroneously uses u8 for load comparison which can
be either char or short. This patch changes the local variable to
u32 which is sufficiently sized, as the loaded value is already
masked and shifted appropriately. Using an integer size avoids
any unnecessary canonicalization from use of non native widths.
This patch is part of a series that adapts the MIPS small word
atomics code for xchg and cmpxchg on short and char to RISC-V.
Cc: RISC-V Patches <patches@groups.riscv.org> Cc: Linux RISC-V <linux-riscv@lists.infradead.org> Cc: Linux MIPS <linux-mips@linux-mips.org> Signed-off-by: Michael Clark <michaeljclark@mac.com>
[paul.burton@mips.com:
- Fix varialble typo per Jonas Gorski.
- Consolidate load variable with other declarations.] Signed-off-by: Paul Burton <paul.burton@mips.com> Fixes: 3ba7f44d2b19 ("MIPS: cmpxchg: Implement 1 byte & 2 byte cmpxchg()") Cc: stable@vger.kernel.org # v4.13+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 18094430d6b5 ("mmc: sdhci-esdhc-imx: add ADMA Length
Mismatch errata fix") involve the fix of ERR004536, but the
fix is incorrect. Double confirm with IC, need to clear the
bit 7 of register 0x6c rather than set this bit 7.
Here is the definition of bit 7 of 0x6c:
0: enable the new IC fix for ERR004536
1: do not use the IC fix, keep the same as before
Find this issue on i.MX845s-evk board when enable CMDQ, and
let system in heavy loading.
In R-Car Gen2 or later, the maximum number of transfer blocks are
changed from 0xFFFF to 0xFFFFFFFF. Therefore, Block Count Register
should use iowrite32().
If another system (U-boot, Hypervisor OS, etc) uses bit[31:16], this
value will not be cleared. So, SD/MMC card initialization fails.
So, check for the bigger register and use apropriate write. Also, mark
the register as extended on Gen2.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: use max_blk_count in if(), add Gen2, update commit message] Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Cc: stable@kernel.org Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
[Ulf: Fixed build error] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
I have encountered an interrupt storm during the eMMC chip probing (and
the chip finally didn't get detected). It turned out that U-Boot left
the DMAC interrupts enabled while the Linux driver didn't use those.
The SDHI driver's interrupt handler somehow assumes that, even if an
SDIO interrupt didn't happen, it should return IRQ_HANDLED. I think
that if none of the enabled interrupts happened and got handled, we
should return IRQ_NONE -- that way the kernel IRQ code recoginizes
a spurious interrupt and masks it off pretty quickly...
Fixes: 7729c7a232a9 ("mmc: tmio: Provide separate interrupt handlers") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When using the mmc_spi driver with a card-detect pin, I noticed that the
card was not detected immediately after probe, but only after it was
unplugged and plugged back in (and the CD IRQ fired).
kvm-unit-tests' eventinj "NMI failing on IDT" test results in NMI being
delivered to the host (L1) when it's running nested. The problem seems to
be: svm_complete_interrupts() raises 'nmi_injected' flag but later we
decide to reflect EXIT_NPF to L1. The flag remains pending and we do NMI
injection upon entry so it got delivered to L1 instead of L2.
It seems that VMX code solves the same issue in prepare_vmcs12(), this was
introduced with code refactoring in commit 5f3d5799974b ("KVM: nVMX: Rework
event injection and recovery").
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Recently, DMG frequency bands have been extended till 71GHz, so extend
the range check till 20GHz (45-71GHZ), else some channels will be marked
as disabled.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@bluwireless.co.uk> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The IBM virtual ethernet driver's polling function continues
to process frames after rescheduling NAPI, resulting in a warning
if it exhausted its budget. Do not restart polling after calling
napi_reschedule. Instead let frames be processed in the following
instance.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
__bpf_redirect() and act_mirred checks this boolean
to determine whether to prefix an ethernet header.
Signed-off-by: Maciej Żenczykowski <maze@google.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The ax88772_bind() should return error code immediately when the PHY
was not reset properly through ax88772a_hw_reset().
Otherwise, The asix_get_phyid() will block when get the PHY
Identifier from the PHYSID1 MII registers through asix_mdio_read()
due to the PHY isn't ready. Furthermore, it will produce a lot of
error message cause system crash.As follows:
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to send
software reset: ffffffb9
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to enable
software MII access
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to read
reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to enable
software MII access
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to read
reg index 0x0000: -71
...
Signed-off-by: Zhang Run <zhang.run@zte.com.cn> Reviewed-by: Yang Wei <yang.wei9@zte.com.cn> Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
sync_inodes_sb() can race against cgwb (cgroup writeback) membership
switches and fail to writeback some inodes. For example, if an inode
switches to another wb while sync_inodes_sb() is in progress, the new
wb might not be visible to bdi_split_work_to_wbs() at all or the inode
might jump from a wb which hasn't issued writebacks yet to one which
already has.
This patch adds backing_dev_info->wb_switch_rwsem to synchronize cgwb
switch path against sync_inodes_sb() so that sync_inodes_sb() is
guaranteed to see all the target wbs and inodes can't jump wbs to
escape syncing.
v2: Fixed misplaced rwsem init. Spotted by Jiufei.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Jiufei Xue <xuejiufei@gmail.com> Link: http://lkml.kernel.org/r/dc694ae2-f07f-61e1-7097-7c8411cee12d@gmail.com Acked-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On a DIO_SKIP_HOLES filesystem, the ->get_block() method is currently
not allowed to create blocks for an empty inode. This confusion comes
from trying to bit shift a negative number, so check the size of the
inode first.
The problem is most visible for hfsplus, because the fallback to
buffered I/O doesn't happen and the write fails with EIO. This is in
part the fault of the module, because it gives a wrong return value on
->get_block(); that will be fixed in a separate patch.
Reviewed-by: Jeff Moyer <jmoyer@redhat.com> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Ernesto A. Fernández <ernesto.mnd.fernandez@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Often userspace doesn't know when the kernel will be calling dma_buf_detach
on the buffer.
If userpace starts its CPU access at the same time as the sg list is being
freed it could end up accessing the sg list after it has been freed.
Thread A Thread B
- DMA_BUF_IOCTL_SYNC IOCT
- ion_dma_buf_begin_cpu_access
- list_for_each_entry
- ion_dma_buf_detatch
- free_duped_table
- dma_sync_sg_for_cpu
Fix this by getting the ion_buffer lock before freeing the sg table memory.
Fixes: 2a55e7b5e544 ("staging: android: ion: Call dma_map_sg for syncing and mapping") Signed-off-by: Liam Mark <lmark@codeaurora.org> Acked-by: Laura Abbott <labbott@redhat.com> Acked-by: Andrew F. Davis <afd@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
moved wake_q_add() before smp_store_release(&q->lock_ptr, NULL), which
could result in futex_wait() waking before observing ->lock_ptr ==
NULL and going back to sleep again.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 1d0dcb3ad9d3 ("futex: Implement lockless wakeups") Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In ieee80211_rx_h_mesh_fwding, we increment the 'dropped_frames_ttl'
counter when we decrement the ttl to zero. For unicast frames
destined for other hosts, we stop processing the frame at that point.
For multicast frames, we do not rebroadcast it in this case, but we
do pass the frame up the stack to process it on this STA. That
doesn't match the usual definition of "dropped," so don't count
those as such.
With this change, something like `ping6 -i0.2 ff02::1%mesh0` from a
peer in a ttl=1 network no longer increments the counter rapidly.
Signed-off-by: Bob Copeland <bobcopeland@fb.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When CONFIG_NO_AUTO_INLINE was present in linux-next (which added
'-fno-inline-functions' to KBUILD_CFLAGS), an allyesconfig build with
Clang failed at the modpost stage:
These functions were marked as extern inline, meaning that if inlining
doesn't happen, the function will be undefined, as it is above.
This happens to work with GCC because the '-fno-inline-functions' option
respects the __inline attribute so all instances of these functions are
inlined as expected and the definition doesn't actually matter. However,
with Clang and '-fno-inline-functions', a function has to be marked with
the __always_inline attribute to be considered for inlining, which none
of these functions are. Clang tries to find the symbol definition
elsewhere as it was told and fails, which trickles down to modpost.
To make sure that this code compiles regardless of compiler and make the
intention of the code clearer, use 'static' to ensure these functions
are always defined, regardless of inlining. Additionally, silence a
checkpatch warning by switching from '__inline' to 'inline'.
Changes since V1:
* Use dev_info instead of printk
* Use dev_warn instead of BUG_ON
Previously, sysfs_create_group was called before all initialization had
fully run - specifically, before pci_set_drvdata was called. Since the
sysctl group is visible to userspace as soon as sysfs_create_group
returns, a small window of time existed during which a process could read
from an uninitialized/partially-initialized device.
This commit moves the creation of the sysctl group to after all
initialized is completed. This ensures that it's impossible for
userspace to read from a sysctl file before initialization has fully
completed.
To catch any future regressions, I've added a check to ensure
that proc_thermal_emum_mode is never PROC_THERMAL_NONE when a process
tries to read from a sysctl file. Previously, the aforementioned race
condition could result in the 'else' branch
running while PROC_THERMAL_NONE was set,
leading to a null pointer deference.
Signed-off-by: Aaron Hill <aa1ronham@gmail.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
| CC mm/nobootmem.o
|In file included from ./include/asm-generic/bug.h:18:0,
| from ./arch/arc/include/asm/bug.h:32,
| from ./include/linux/bug.h:5,
| from ./include/linux/mmdebug.h:5,
| from ./include/linux/gfp.h:5,
| from ./include/linux/slab.h:15,
| from mm/nobootmem.c:14:
|mm/nobootmem.c: In function '__free_pages_memory':
|./include/linux/kernel.h:845:29: warning: comparison of distinct pointer types lacks a cast
| (!!(sizeof((typeof(x) *)1 == (typeof(y) *)1)))
| ^
|./include/linux/kernel.h:859:4: note: in expansion of macro '__typecheck'
| (__typecheck(x, y) && __no_side_effects(x, y))
| ^~~~~~~~~~~
|./include/linux/kernel.h:869:24: note: in expansion of macro '__safe_cmp'
| __builtin_choose_expr(__safe_cmp(x, y), \
| ^~~~~~~~~~
|./include/linux/kernel.h:878:19: note: in expansion of macro '__careful_cmp'
| #define min(x, y) __careful_cmp(x, y, <)
| ^~~~~~~~~~~~~
|mm/nobootmem.c:104:11: note: in expansion of macro 'min'
| order = min(MAX_ORDER - 1UL, __ffs(start));
Change __ffs return value from 'int' to 'unsigned long' as it
is done in other implementations (like asm-generic, x86, etc...)
to avoid build-time warnings in places where type is strictly
checked.
As __ffs may return values in [0-31] interval changing return
type to unsigned is valid.
gpio-mockup-chardev.c: In function ‘get_debugfs’:
gpio-mockup-chardev.c:62:3: warning: ignoring return value of ‘asprintf’, declared with attribute warn_unused_result [-Wunused-result]
asprintf(path, "%s/gpio", mnt_fs_get_target(fs));
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
seccomp_bpf fails to build due to undefined reference errors:
aarch64-linaro-linux-gcc --sysroot=/build/tmp-rpb-glibc/sysroots/hikey
-O2 -pipe -g -feliminate-unused-debug-types -Wl,-no-as-needed -Wall
-Wl,-O1 -Wl,--hash-style=gnu -Wl,--as-needed -lpthread seccomp_bpf.c -o
/build/tmp-rpb-glibc/work/hikey-linaro-linux/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf
/tmp/ccrlR3MW.o: In function `tsync_sibling':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1920: undefined reference to `sem_post'
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1920: undefined reference to `sem_post'
/tmp/ccrlR3MW.o: In function `TSYNC_setup':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1863: undefined reference to `sem_init'
/tmp/ccrlR3MW.o: In function `TSYNC_teardown':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1904: undefined reference to `sem_destroy'
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1897: undefined reference to `pthread_kill'
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1898: undefined reference to `pthread_cancel'
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1899: undefined reference to `pthread_join'
/tmp/ccrlR3MW.o: In function `tsync_start_sibling':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'
/tmp/ccrlR3MW.o: In function `TSYNC_siblings_fail_prctl':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1978: undefined reference to `sem_wait'
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1990: undefined reference to `pthread_join'
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1992: undefined reference to `pthread_join'
/tmp/ccrlR3MW.o: In function `tsync_start_sibling':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'
/tmp/ccrlR3MW.o: In function `TSYNC_two_siblings_with_ancestor':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2016: undefined reference to `sem_wait'
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2032: undefined reference to `pthread_join'
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2034: undefined reference to `pthread_join'
/tmp/ccrlR3MW.o: In function `tsync_start_sibling':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'
/tmp/ccrlR3MW.o: In function `TSYNC_two_sibling_want_nnp':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2046: undefined reference to `sem_wait'
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2058: undefined reference to `pthread_join'
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2060: undefined reference to `pthread_join'
/tmp/ccrlR3MW.o: In function `tsync_start_sibling':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'
/tmp/ccrlR3MW.o: In function `TSYNC_two_siblings_with_no_filter':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2073: undefined reference to `sem_wait'
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2098: undefined reference to `pthread_join'
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2100: undefined reference to `pthread_join'
/tmp/ccrlR3MW.o: In function `tsync_start_sibling':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'
/tmp/ccrlR3MW.o: In function `TSYNC_two_siblings_with_one_divergence':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2125: undefined reference to `sem_wait'
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2143: undefined reference to `pthread_join'
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2145: undefined reference to `pthread_join'
/tmp/ccrlR3MW.o: In function `tsync_start_sibling':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'
/tmp/ccrlR3MW.o: In function `TSYNC_two_siblings_not_under_filter':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2169: undefined reference to `sem_wait'
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2202: undefined reference to `pthread_join'
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:2227: undefined reference to `pthread_join'
/tmp/ccrlR3MW.o: In function `tsync_start_sibling':
/usr/src/debug/kselftests/4.12-r0/linux-4.12-rc7/tools/testing/selftests/seccomp/seccomp_bpf.c:1941: undefined reference to `pthread_create'
It's GNU Make and linker specific.
The default Makefile rule looks like:
$(CC) $(CFLAGS) $(LDFLAGS) $@ $^ $(LDLIBS)
When linking is done by gcc itself, no issue, but when it needs to be passed
to proper ld, only LDLIBS follows and then ld cannot know what libs to link
with.
More detail:
https://www.gnu.org/software/make/manual/html_node/Implicit-Variables.html
LDFLAGS
Extra flags to give to compilers when they are supposed to invoke the linker,
‘ld’, such as -L. Libraries (-lfoo) should be added to the LDLIBS variable
instead.
LDLIBS
Library flags or names given to compilers when they are supposed to invoke the
linker, ‘ld’. LOADLIBES is a deprecated (but still supported) alternative to
LDLIBS. Non-library linker flags, such as -L, should go in the LDFLAGS
variable.
https://lkml.org/lkml/2010/2/10/362
tools/perf: libraries must come after objects
Link order matters, use LDLIBS instead of LDFLAGS to properly link against
libpthread.
Change snprintf to scnprintf. There are generally two cases where using
snprintf causes problems.
1) Uses of size += snprintf(buf, SIZE - size, fmt, ...)
In this case, if snprintf would have written more characters than what the
buffer size (SIZE) is, then size will end up larger than SIZE. In later
uses of snprintf, SIZE - size will result in a negative number, leading
to problems. Note that size might already be too large by using
size = snprintf before the code reaches a case of size += snprintf.
2) If size is ultimately used as a length parameter for a copy back to user
space, then it will potentially allow for a buffer overflow and information
disclosure when size is greater than SIZE. When the size is used to index
the buffer directly, we can have memory corruption. This also means when
size = snprintf... is used, it may also cause problems since size may become
large. Copying to userspace is mitigated by the HARDENED_USERCOPY kernel
configuration.
The solution to these issues is to use scnprintf which returns the number of
characters actually written to the buffer, so the size variable will never
exceed SIZE.
Signed-off-by: Silvio Cesare <silvio.cesare@gmail.com> Cc: Timur Tabi <timur@kernel.org> Cc: Nicolin Chen <nicoleotsuka@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Xiubo Li <Xiubo.Lee@gmail.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: Kees Cook <keescook@chromium.org> Cc: Will Deacon <will.deacon@arm.com> Cc: Greg KH <greg@kroah.com> Signed-off-by: Willy Tarreau <w@1wt.eu> Acked-by: Nicolin Chen <nicoleotsuka@gmail.com> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Change snprintf to scnprintf. There are generally two cases where using
snprintf causes problems.
1) Uses of size += snprintf(buf, SIZE - size, fmt, ...)
In this case, if snprintf would have written more characters than what the
buffer size (SIZE) is, then size will end up larger than SIZE. In later
uses of snprintf, SIZE - size will result in a negative number, leading
to problems. Note that size might already be too large by using
size = snprintf before the code reaches a case of size += snprintf.
2) If size is ultimately used as a length parameter for a copy back to user
space, then it will potentially allow for a buffer overflow and information
disclosure when size is greater than SIZE. When the size is used to index
the buffer directly, we can have memory corruption. This also means when
size = snprintf... is used, it may also cause problems since size may become
large. Copying to userspace is mitigated by the HARDENED_USERCOPY kernel
configuration.
The solution to these issues is to use scnprintf which returns the number of
characters actually written to the buffer, so the size variable will never
exceed SIZE.
Signed-off-by: Silvio Cesare <silvio.cesare@gmail.com> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: Kees Cook <keescook@chromium.org> Cc: Will Deacon <will.deacon@arm.com> Cc: Greg KH <greg@kroah.com> Signed-off-by: Willy Tarreau <w@1wt.eu> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If all CPUs in the irq_default_affinity mask are offline when an interrupt
is initialized then irq_setup_affinity() can set an empty affinity mask for
a newly allocated interrupt.
Fix this by falling back to cpu_online_mask in case the resulting affinity
mask is zero.
The source_sink_alloc_func() function is supposed to return error
pointers on error. The function is called from usb_get_function() which
doesn't check for NULL returns so it would result in an Oops.
Of course, in the current kernel, small allocations always succeed so
this doesn't affect runtime.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently the link_state is uninitialized and the default value is 0(U0)
before the first time we start the udc, and after we start the udc then
stop the udc, the link_state will be undefined.
We may have the following warnings if we start the udc again with
an undefined link_state:
WARNING: CPU: 0 PID: 327 at drivers/usb/dwc3/gadget.c:294 dwc3_send_gadget_ep_cmd+0x304/0x308
dwc3 100e0000.hidwc3_0: wakeup failed --> -22
[...]
Call Trace:
[<c010f270>] (unwind_backtrace) from [<c010b3d8>] (show_stack+0x10/0x14)
[<c010b3d8>] (show_stack) from [<c034a4dc>] (dump_stack+0x84/0x98)
[<c034a4dc>] (dump_stack) from [<c0118000>] (__warn+0xe8/0x100)
[<c0118000>] (__warn) from [<c0118050>](warn_slowpath_fmt+0x38/0x48)
[<c0118050>] (warn_slowpath_fmt) from [<c0442ec0>](dwc3_send_gadget_ep_cmd+0x304/0x308)
[<c0442ec0>] (dwc3_send_gadget_ep_cmd) from [<c0445e68>](dwc3_ep0_start_trans+0x48/0xf4)
[<c0445e68>] (dwc3_ep0_start_trans) from [<c0446750>](dwc3_ep0_out_start+0x64/0x80)
[<c0446750>] (dwc3_ep0_out_start) from [<c04451c0>](__dwc3_gadget_start+0x1e0/0x278)
[<c04451c0>] (__dwc3_gadget_start) from [<c04452e0>](dwc3_gadget_start+0x88/0x10c)
[<c04452e0>] (dwc3_gadget_start) from [<c045ee54>](udc_bind_to_driver+0x88/0xbc)
[<c045ee54>] (udc_bind_to_driver) from [<c045f29c>](usb_gadget_probe_driver+0xf8/0x140)
[<c045f29c>] (usb_gadget_probe_driver) from [<bf005424>](gadget_dev_desc_UDC_store+0xac/0xc4 [libcomposite])
[<bf005424>] (gadget_dev_desc_UDC_store [libcomposite]) from[<c023d8e0>] (configfs_write_file+0xd4/0x160)
[<c023d8e0>] (configfs_write_file) from [<c01d51e8>] (__vfs_write+0x1c/0x114)
[<c01d51e8>] (__vfs_write) from [<c01d5ff4>] (vfs_write+0xa4/0x168)
[<c01d5ff4>] (vfs_write) from [<c01d6d40>] (SyS_write+0x3c/0x90)
[<c01d6d40>] (SyS_write) from [<c0107400>] (ret_fast_syscall+0x0/0x3c)
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We see dwc3 endpoint stopped by unwanted irq during
suspend resume test, which is caused dwc3 ep can't be started
with error "No Resource".
Here, add synchronize_irq before suspend to sync the
pending IRQ handlers complete.
Signed-off-by: Bo He <bo.he@intel.com> Signed-off-by: Yu Wang <yu.y.wang@intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In case the upstream clock are not set, which can happen in case the
VC5 has no valid upstream clock, the $src variable is used uninited
by regmap_update_bits(). Check for this condition and return -EINVAL
in such case.
Note that in case the VC5 has no valid upstream clock, the VC5 can
not operate correctly. That is a hardware property of the VC5. The
internal oscilator present in some VC5 models is also considered
upstream clock.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Alexey Firago <alexey_firago@mentor.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Stephen Boyd <sboyd@kernel.org> Cc: linux-renesas-soc@vger.kernel.org
[sboyd@kernel.org: Added comment about probe preventing this from
happening in the first place] Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Inside function rt274_i2c_probe(), if regmap_read() function
returns -EINVAL, then local variable "val" leaves uninitialized
but used in if statement. This is potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The problem is seen in the q6asm_dai_compr_set_params() function:
ret = q6asm_map_memory_regions(dir, prtd->audio_client, prtd->phys,
(prtd->pcm_size / prtd->periods),
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
prtd->periods);
In this code prtd->pcm_size is the buffer_size and prtd->periods comes
from params->buffer.fragments. If we allow the number of fragments to
be zero then it results in a divide by zero bug. One possible fix would
be to use prtd->pcm_count directly instead of using the division to
re-calculate it. But I decided that it doesn't really make sense to
allow zero fragments.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For some reason this field was set to zero when all other drivers use
.dynamic = 1 for front-ends. This change was tested on Dell XPS13 and
has no impact with the existing legacy driver. The SOF driver also works
with this change which enables it to override the fixed topology.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Prevents deadlock when fifo is full and reader closes file.
Signed-off-by: Kristian H. Kristensen <hoegsberg@chromium.org> Signed-off-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Broadcom tags inserted by Broadcom switches put a 4 byte header after
the MAC SA and before the EtherType, which may look like some sort of 0
length LLC/SNAP packet (tcpdump and wireshark do think that way). With
ACS enabled in stmmac the packets were truncated to 8 bytes on
reception, whereas clearing this bit allowed normal reception to occur.
In order to make that possible, we need to pass a net_device argument to
the different core_init() functions and we are dependent on the Broadcom
tagger padding packets correctly (which it now does). To be as little
invasive as possible, this is only done for gmac1000 when the network
device is DSA-enabled (netdev_uses_dsa() returns true).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Niklas Cassel <niklas.cassel@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A proc_remove() can sleep. so that it can't be inside of spin_lock.
Hence proc_remove() is moved to outside of spin_lock. and it also
adds mutex to sync create and remove of proc entry(config->pde).
Forwarded packets enter the tx path through ieee80211_add_pending_skb,
which skips the ieee80211_skb_resize call.
Fixes WARN_ON in ccmp_encrypt_skb and resulting packet loss.
Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
drm_dp_mst_topology_mgr_suspend() is added into the new reboot
sequence, which disables the UP request at the beginning.
Therefore sideband messages are blocked.
[How]
Finish MST sideband message transaction before UP request is
suppressed.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com> Reviewed-by: Roman Li <Roman.Li@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On HP ProBook 4540s, if PM-runtime is enabled in the radeon driver
and the direct-complete optimization is used for the radeon device
during system-wide suspend, the system doesn't resume.
Preventing direct-complete from being used with the radeon device by
setting the DPM_FLAG_NEVER_SKIP driver flag for it makes the problem
go away, which indicates that direct-complete is not safe for the
radeon driver in general and should not be used with it (at least
for now).
This fixes a regression introduced by commit c62ec4610c40
("PM / core: Fix direct_complete handling for devices with no
callbacks") which allowed direct-complete to be applied to
devices without PM callbacks (again) which in turn unlocked
direct-complete for radeon on HP ProBook 4540s.
Fixes: c62ec4610c40 ("PM / core: Fix direct_complete handling for devices with no callbacks") Link: https://bugzilla.kernel.org/show_bug.cgi?id=201519 Reported-by: Ярослав Семченко <ukrkyi@gmail.com> Tested-by: Ярослав Семченко <ukrkyi@gmail.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When using ATPX to control dGPU power, the state is not retained
across suspend and resume cycles by default. This can probably
be loosened for Hybrid Graphics (_PR3) laptops where I think the
state is properly retained.
Fixes: c62ec4610c40 ("PM / core: Fix direct_complete handling for devices with no callbacks") Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In sctp_stream_init(), after sctp_stream_outq_migrate() freed the
surplus streams' ext, but sctp_stream_alloc_out() returns -ENOMEM,
stream->outcnt will not be set to 'outcnt'.
With the bigger value on stream->outcnt, when closing the assoc and
freeing its streams, the ext of those surplus streams will be freed
again since those stream exts were not set to NULL after freeing in
sctp_stream_outq_migrate(). Then the invalid-free issue reported by
syzbot would be triggered.
We fix it by simply setting them to NULL after freeing.
Fixes: 5bbbbe32a431 ("sctp: introduce stream scheduler foundations") Reported-by: syzbot+58e480e7b28f2d890bfd@syzkaller.appspotmail.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Fix the refcounting of the authentication keys in the file locking code.
The vnode->lock_key member points to a key on which it expects to be
holding a ref, but it isn't always given an extra ref, however.
In case of ->set_param() and ->bind_conn() cxgb4i driver does not wait for
cmd completion, this can create race conditions, to avoid this add
wait_for_completion().
Signed-off-by: Varun Prakash <varun@chelsio.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Albeit we no longer rely on those hard-coded descriptor sizes, we still use
them as our defaults, so better get it right. While adding its sysfs
entries, we forgot to update the geometry descriptor size. It is 0x48
according to UFS2.1, and wasn't changed in UFS3.0.
[mkp: typo]
Fixes: c720c091222e (scsi: ufs: sysfs: geometry descriptor) Signed-off-by: Avri Altman <avri.altman@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
projects / mirror_ubuntu-bionic-kernel.git / log