Since the offset is added directly to the hva from the
gfn_to_hva_cache, a negative offset could result in an out of bounds
write. The existing BUG_ON only checks for addresses beyond the end of
the gfn_to_hva_cache, not for addresses before the start of the
gfn_to_hva_cache.
Note that all current call sites have non-negative offsets.
For fadump to work successfully there should not be any holes in reserved
memory ranges where kernel has asked firmware to move the content of old
kernel memory in event of crash. Now that fadump uses CMA for reserved
area, this memory area is now not protected from hot-remove operations
unless it is cma allocated. Hence, fadump service can fail to re-register
after the hot-remove operation, if hot-removed memory belongs to fadump
reserved region. To avoid this make sure that memory from fadump reserved
area is not hot-removable if fadump is registered.
However, if user still wants to remove that memory, he can do so by
manually stopping fadump service before hot-remove operation.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
AMD doesn't seem to implement MSR_IA32_MCG_EXT_CTL and svm code in kvm
knows nothing about it, however, this MSR is among emulated_msrs and
thus returned with KVM_GET_MSR_INDEX_LIST. The consequent KVM_GET_MSRS,
of course, fails.
Report the MSR as unsupported to not confuse userspace.
The GPIOAO pins (as well as the two exotic GPIO_BSD_EN and GPIO_TEST_N)
only belong to the pin controller in the AO domain. With the current
definition these pins cannot be referred to in .dts files as group
(which is possible on GXBB and GXL for example).
Add a separate "gpio_aobus" function to fix the mapping between the pin
controller and the GPIO pins in the AO domain. This is similar to how
the GXBB and GXL drivers implement this functionality.
Fixes: 9dab1868ec0db4 ("pinctrl: amlogic: Make driver independent from two-domain configuration") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The GPIOAO pins (as well as the two exotic GPIO_BSD_EN and GPIO_TEST_N)
only belong to the pin controller in the AO domain. With the current
definition these pins cannot be referred to in .dts files as group
(which is possible on GXBB and GXL for example).
Add a separate "gpio_aobus" function to fix the mapping between the pin
controller and the GPIO pins in the AO domain. This is similar to how
the GXBB and GXL drivers implement this functionality.
Fixes: 9dab1868ec0db4 ("pinctrl: amlogic: Make driver independent from two-domain configuration") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When unregistering fbdev using unregister_framebuffer(), any bound
console will unbind automatically. This is working fine if this is the
only framebuffer, resulting in a switch to the dummy console. However if
there is a fb0 and I unregister fb1 having a bound console, I eventually
get a crash. The fastest way for me to trigger the crash is to do a
reboot, resulting in this splat:
The problem is in the console rebinding in fbcon_fb_unbind(). It uses the
virtual console index as the new framebuffer index to bind the console(s)
to. The correct way is to use the con2fb_map lookup table to find the
framebuffer index.
In __ghes_panic() clear the block status in the APEI generic
error status block for that generic hardware error source before
calling panic() to prevent a second panic() in the crash kernel
for exactly the same fatal error.
Otherwise ghes_probe(), running in the crash kernel, would see
an unhandled error in the APEI generic error status block and
panic again, thereby precluding any crash dump.
Signed-off-by: Lenny Szubowicz <lszubowi@redhat.com> Signed-off-by: David Arcari <darcari@redhat.com> Tested-by: Tyler Baicar <baicar.tyler@gmail.com> Acked-by: Borislav Petkov <bp@suse.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
i40iw_net_event() reads unconditionally 16 bytes from
neigh->primary_key while the memory allocated for
"neighbour" struct is evaluated in neigh_alloc() as
tbl->entry_size + dev->neigh_priv_len
where "dev" is a net_device.
But the driver does not setup dev->neigh_priv_len and
we read beyond the neigh entry allocated memory,
so the patch in the next mail fixes this.
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Blitting an image with "negative" offsets is not working since there
is no clipping. It hopefully just crashes. For the bootup logo, there
is protection so that blitting does not happen as the image is drawn
further and further to the right (ROTATE_UR) or further and further
down (ROTATE_CW). There is however no protection when drawing in the
opposite directions (ROTATE_UD and ROTATE_CCW).
Add back this protection.
The regression is 20-odd years old but the mindless warning-killing
mentality displayed in commit 34bdb666f4b2 ("fbdev: fbmem: remove
positive test on unsigned values") is also to blame, methinks.
Fixes: 448d479747b8 ("fbdev: fb_do_show_logo() updates") Signed-off-by: Peter Rosin <peda@axentia.se> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Fabian Frederick <ffrederick@users.sourceforge.net> Cc: Geert Uytterhoeven <geert+renesas@glider.be>
cc: Geoff Levand <geoff@infradead.org> Cc: James Simmons <jsimmons@users.sf.net> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There are several warnings from Clang about no case statement matching
the constant 0:
In file included from drivers/block/drbd/drbd_receiver.c:48:
In file included from drivers/block/drbd/drbd_int.h:48:
In file included from ./include/linux/drbd_genl_api.h:54:
In file included from ./include/linux/genl_magic_struct.h:236:
./include/linux/drbd_genl.h:321:1: warning: no case matching constant
switch condition '0'
GENL_struct(DRBD_NLA_HELPER, 24, drbd_helper_info,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/genl_magic_struct.h:220:10: note: expanded from macro
'GENL_struct'
switch (0) {
^
Silence this warning by adding a 'case 0:' statement. Additionally,
adjust the alignment of the statements in the ct_assert_unique macro to
avoid a checkpatch warning.
This solution was originally sent by Arnd Bergmann with a default case
statement: https://lore.kernel.org/patchwork/patch/756723/
If you try to promote a Secondary while connected to a Primary
and allow-two-primaries is NOT set, we will wait for "ping-timeout"
to give this node a chance to detect a dead primary,
in case the cluster manager noticed faster than we did.
But if we then are *still* connected to a Primary,
we fail (after an additional timeout of ping-timout).
This change skips the spurious second timeout.
Most people won't notice really,
since "ping-timeout" by default is half a second.
But in some installations, ping-timeout may be 10 or 20 seconds or more,
and spuriously delaying the error return becomes annoying.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
With "on-no-data-accessible suspend-io", DRBD requires the next attach
or connect to be to the very same data generation uuid tag it lost last.
If we first lost connection to the peer,
then later lost connection to our own disk,
we would usually refuse to re-connect to the peer,
because it presents the wrong data set.
However, if the peer first connects without a disk,
and then attached its disk, we accepted that same wrong data set,
which would be "unexpected" by any user of that DRBD
and cause "undefined results" (read: very likely data corruption).
The fix is to forcefully disconnect as soon as we notice that the peer
attached to the "wrong" dataset.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
MMCRA[34:36] and MMCRA[38:44] expose the thresholding counter value.
Thresholding counter can be used to count latency cycles such as
load miss to reload. But threshold counter value is not relevant
when the sampled instruction type is unknown or reserved. Patch to
fix the thresholding counter value to zero when sampled instruction
type is unknown or reserved.
Fixes: 170a315f41c6('powerpc/perf: Support to export MMCRA[TEC*] field to userspace') Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The function cw1200_bss_info_changed() and cw1200_hw_scan() can be
concurrently executed.
The two functions both access a possible shared variable "frame.skb".
This shared variable is freed by dev_kfree_skb() in cw1200_upload_beacon(),
which is called by cw1200_bss_info_changed(). The free operation is
protected by a mutex lock "priv->conf_mutex" in cw1200_bss_info_changed().
In cw1200_hw_scan(), this shared variable is accessed without the
protection of the mutex lock "priv->conf_mutex".
Thus, concurrency use-after-free bugs may occur.
To fix these bugs, the original calls to mutex_lock(&priv->conf_mutex) and
mutex_unlock(&priv->conf_mutex) are moved to the places, which can
protect the accesses to the shared variable.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
- fix race condition when a unit is deleted after an RLL,
and before we have gotten the LV_STATUS page of the unit.
- In this case we will get a standard inquiry, rather than
the desired page. This will result in a unit presented
which no longer exists.
- If we ask for LV_STATUS, insure we get LV_STATUS
Reviewed-by: Murthy Bhat <murthy.bhat@microsemi.com> Reviewed-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com> Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Dave Carroll <david.carroll@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When a LAG device or a VLAN device on top of it is enslaved to a bridge,
the driver propagates the CHANGEUPPER event to the LAG's slaves.
This causes each physical port to increase the reference count of the
internal representation of the bridge port by calling
mlxsw_sp_port_bridge_join().
However, when a port is removed from a LAG, the corresponding leave()
function is not called and the reference count is not decremented. This
leads to ugly hacks such as mlxsw_sp_bridge_port_should_destroy() that
try to understand if the bridge port should be destroyed even when its
reference count is not 0.
Instead, make sure that when a port is unlinked from a LAG it would see
the same events as if the LAG (or its uppers) were unlinked from a
bridge.
The above is achieved by walking the LAG's uppers when a port is
unlinked and calling mlxsw_sp_port_bridge_leave() for each upper that is
enslaved to a bridge.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Due to the alignment handling, it actually matters where in the code
we add the 4 bytes for the presence bitmap to the length; the first
field is the timestamp with 8 byte alignment so we need to add the
space for the extra vendor namespace presence bitmap *before* we do
any alignment for the fields.
Move the presence bitmap length accounting to the right place to fix
the alignment for the data properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
From Michael Cree:
"Bisection lead to commit b38d08f3181c ("percpu: restructure
locking") as being the cause of lockups at initial boot on
the kernel built for generic Alpha.
On a suggestion by Tejun Heo that:
So, the only thing I can think of is that it's calling
spin_unlock_irq() while irq handling isn't set up yet.
Can you please try the followings?
1. Convert all spin_[un]lock_irq() to
spin_lock_irqsave/unlock_irqrestore()."
Fixes: b38d08f3181c ("percpu: restructure locking") Reported-and-tested-by: Michael Cree <mcree@orcon.net.nz> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Dennis Zhou <dennis@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Due to lack of ID pin interrupt event on AM335x devices, the musb dsps
driver uses polling to detect usb device attach for dual-role port.
But in the case if a micro-A cable adapter is attached without a USB device
attached to the cable, the musb state machine gets stuck in a_wait_vrise
state waiting for the MUSB_CONNECT interrupt which won't happen due to the
usb device is not attached. The state is stuck in a_wait_vrise even after
the micro-A cable is detached, which could cause VBUS retention if then the
dual-role port is attached to a host port.
To fix the problem, make a_wait_vrise as a transient state, then move the
state to either a_wait_bcon for host port or a_idle state for dual-role
port, if no usb device is attached to the port.
Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When we emulate an MMIO instruction, we advance the CPU state within
decode_hsr(), before emulating the instruction effects.
Having this logic in decode_hsr() is opaque, and advancing the state
before emulation is problematic. It gets in the way of applying
consistent single-step logic, and it prevents us from being able to fail
an MMIO instruction with a synchronous exception.
Clean this up by only advancing the CPU state *after* the effects of the
instruction are emulated.
Cc: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Alex Bennée <alex.bennee@linaro.org> Reviewed-by: Christoffer Dall <christoffer.dall@arm.com> Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The strncpy() function may leave the destination string buffer
unterminated, better use strlcpy() that we have a __weak fallback
implementation for systems without it.
In this case the 'target' buffer is coming from a list of build-ids that
are expected to have a len of at most (SBUILD_ID_SIZE - 1) chars, so
probably we're safe, but since we're using strncpy() here, use strlcpy()
instead to provide the intended safety checking without the using the
problematic strncpy() function.
This fixes this warning on an Alpine Linux Edge system with gcc 8.2:
util/probe-file.c: In function 'probe_cache__open.isra.5':
util/probe-file.c:427:3: error: 'strncpy' specified bound 41 equals destination size [-Werror=stringop-truncation]
strncpy(sbuildid, target, SBUILD_ID_SIZE);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Cc: Namhyung Kim <namhyung@kernel.org> Fixes: 1f3736c9c833 ("perf probe: Show all cached probes") Link: https://lkml.kernel.org/n/tip-l7n8ggc9kl38qtdlouke5yp5@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The strncpy() function may leave the destination string buffer
unterminated, better use strlcpy() that we have a __weak fallback
implementation for systems without it.
This fixes this warning on an Alpine Linux Edge system with gcc 8.2:
util/header.c: In function 'perf_event__synthesize_event_update_unit':
util/header.c:3586:2: error: 'strncpy' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
strncpy(ev->data, evsel->unit, size);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
util/header.c:3579:16: note: length computed here
size_t size = strlen(evsel->unit);
^~~~~~~~~~~~~~~~~~~
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Fixes: a6e5281780d1 ("perf tools: Add event_update event unit type") Link: https://lkml.kernel.org/n/tip-fiikh5nay70bv4zskw2aa858@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 391f93f2ec9f ("serial: core: Rework hw-assited flow control support")
has changed the way the autoCTS mode is handled.
According to that change, serial drivers which enable H/W autoCTS mode must
set UPSTAT_AUTOCTS to prevent the serial core from inadvertently disabling
TX. This patch adds proper handling of UPSTAT_AUTOCTS flag.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
[mszyprow: rephrased commit message] Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The bcm2835 mmc host tends to lock up for unknown reason so reset it on
timeout. The upper mmc block layer tries retransimitting with single
blocks which tends to work out after a long wait.
This is better than giving up and leaving the machine broken for no
obvious reason.
Fixes: 660fc733bd74 ("mmc: bcm2835: Add new driver for the sdhost controller.") Signed-off-by: Michal Suchanek <msuchanek@suse.de> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Acked-by: Eric Anholt <eric@anholt.net> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If the user issues an "mmc extcsd read", the SD controller receives
what it thinks is a SEND_IF_COND command with an unexpected data block.
The resulting operations leave the FSM stuck in READWAIT, a state which
persists until the MMC framework resets the controller, by which point
the root filesystem is likely to have been unmounted.
A less heavyweight solution is to detect the condition and nudge the
FSM by asserting the (self-clearing) FORCE_DATA_MODE bit.
Link: https://github.com/raspberrypi/linux/issues/2728 Signed-off-by: Phil Elwell <phil@raspberrypi.org> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Acked-by: Eric Anholt <eric@anholt.net> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The kvm capability KVM_CAP_SPAPR_TCE_VFIO is used to indicate the
availability of in kernel tce acceleration for vfio. However it is
currently the case that this is only available on a powernv machine,
not for a pseries machine.
Thus make this capability dependent on having the cpu feature
CPU_FTR_HVMODE.
[paulus@ozlabs.org - fixed compilation for Book E.]
eukrea-tlv320.c machine driver runs on non-DT platforms
and include <asm/mach-types.h> header file in order to be able
to use some machine_is_eukrea_xxx() macros.
Building it for ARM64 causes the following build error:
sound/soc/fsl/eukrea-tlv320.c:28:10: fatal error: asm/mach-types.h: No such file or directory
Avoid this error by not allowing to build the SND_SOC_EUKREA_TLV320
driver when ARM64 is selected.
This is needed in preparation for the i.MX8M support.
Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Fabio Estevam <festevam@gmail.com> Acked-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
WARNING: vmlinux.o(.text+0x19f90): Section mismatch in reference from the function littleton_init_lcd() to the function .init.text:pxa_set_fb_info()
The function littleton_init_lcd() references
the function __init pxa_set_fb_info().
This is often because littleton_init_lcd lacks a __init
annotation or the annotation of pxa_set_fb_info is wrong.
WARNING: vmlinux.o(.text+0xf824): Section mismatch in reference from the function zeus_register_ohci() to the function .init.text:pxa_set_ohci_info()
The function zeus_register_ohci() references
the function __init pxa_set_ohci_info().
This is often because zeus_register_ohci lacks a __init
annotation or the annotation of pxa_set_ohci_info is wrong.
WARNING: vmlinux.o(.text+0xf95c): Section mismatch in reference from the function cm_x300_init_u2d() to the function .init.text:pxa3xx_set_u2d_info()
The function cm_x300_init_u2d() references
the function __init pxa3xx_set_u2d_info().
This is often because cm_x300_init_u2d lacks a __init
annotation or the annotation of pxa3xx_set_u2d_info is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For some reason, my older GCC (< 4.8) isn't smart enough to optimize the
!__builtin_constant_p() branch in bpf_htons, I see:
error: implicit declaration of function '__builtin_bswap16'
Let's use __bpf_constant_htons as suggested by Daniel Borkmann.
I tried to use simple htons, but it produces the following:
test_progs.c:54:17: error: braced-group within expression allowed only
inside a function
.eth.h_proto = htons(ETH_P_IP),
Signed-off-by: Stanislav Fomichev <sdf@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In the ioctl_event_ctl() SWITCHTEC_IOCTL_EVENT_IDX_ALL case, we call
event_ctl() several times with the same "ctl" struct. Each call clobbers
ctl.flags, which leads to the problem that we may not actually enable or
disable all events as the user requested.
Preserve the event flag value with a temporary variable.
When inode is corrupted so that extent type is invalid, some functions
(such as udf_truncate_extents()) will just BUG. Check that extent type
is valid when loading the inode to memory.
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
It was observed that when using seqentional mode contrary to the
documentation, the SS bit (which is supposed to only be set if
automatic/sequence command completed normally), is sometimes set
together with NA (NAK in address phase) causing transfer to falsely be
considered successful.
My assumption is that this does not happen during manual mode since the
controller is stopping its work the moment it sets NA/ND bit in status
register. This is not the case in Automatic/Sequentional mode where it
is still working to send STOP condition and the actual status we get
depends on the time when the ISR is run.
This patch changes the order of checking status bits in ISR - error
conditions are checked first and only if none of them occurred, the
transfer may be considered successful. This is required to introduce
using of sequentional mode in next patch.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com> Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The value of opp_table->regulator_count is not very consistent right now
and it may end up being 0 while we do have a "opp-microvolt" property in
the OPP table. It was kept that way as we used to check if any
regulators are set with the OPP core for a device or not using value of
regulator_count.
Lets use opp_table->regulators for that purpose as the meaning of
regulator_count is going to change in the later patches.
of_find_node_by_path() acquires a reference to the node
returned by it and that reference needs to be dropped by its caller.
bl_idle_init() doesn't do that, so fix it.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Same as other i.MX6 SoCs, ensure unused MMDC channel's
handshake is bypassed, this is to make sure no request
signal will be generated when periphe_clk_sel is changed
or SRC warm reset is triggered.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The driver overrides the error codes returned by platform_get_irq() to
-EINVAL, so if it returns -EPROBE_DEFER, the driver would fail the probe
permanently instead of the deferred probing. Switch to propagating the
error code upstream, still checking/overriding IRQ0 as libata regards it
as "no IRQ" (thus polling) anyway...
Fixes: 9ec36cafe43b ("of/irq: do irq resolution in platform_get_irq") Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
After removing an entry from a queue (e.g. reading an event in
arm_smmu_evtq_thread()) it is necessary to advance the MMIO consumer
pointer to free the queue slot back to the SMMU. A memory barrier is
required here so that all reads targetting the queue entry have
completed before the consumer pointer is updated.
The implementation of queue_inc_cons() relies on a writel() to complete
the previous reads, but this is incorrect because writel() is only
guaranteed to complete prior writes. This patch replaces the call to
writel() with an mb(); writel_relaxed() sequence, which gives us the
read->write ordering which we require.
Cc: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
qcom,smmu-v2 is an arm,smmu-v2 implementation with specific
clock and power requirements.
On msm8996, multiple cores, viz. mdss, video, etc. use this
smmu. On sdm845, this smmu is used with gpu.
Add bindings for the same.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org> Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Tomasz Figa <tfiga@chromium.org> Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Reviewed-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In stream mode, when fast-forwarding TRBs, the stream number
is not cleared causing the new stream to not get assigned. So
we don't want controller to carry on transfers when short packet
is received. So disable the CSP for stream capable endpoint.
This is based on the 3.30a Programming guide, where table 3-1
device descriptor structure field definitions says for CSP bit
If this bit is 0, the controller generates an XferComplete event
and remove the stream. So if we keep CSP as 1 then switching between
streams would not happen as in stream mode, when fast-forwarding
TRBs, the stream number is not cleared causing the new stream to not get
assigned.
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The datasheet says we must stop the timer before changing the clock
divider. This can happen when the restart handler is called while the
watchdog is running.
Here "flash" is obviously the whole device and we know "rootfs"
is a bogus hack to point to a squashfs rootfs inside of the main
"upgrade partition". We know "RedBoot" is the first 0x40000 of
the flash and the "upgrade" partition follows from 0x40000 to
0x1f8000. So we have mtd0, 1, 4 and 6 covered.
Add support for the third loop filter mode
V4L2_MPEG_VIDEO_H264_LOOP_FILTER_MODE_DISABLED_AT_SLICE_BOUNDARY,
and fix V4L2_CID_MPEG_VIDEO_H264_LOOP_FILTER_ALPHA and
V4L2_CID_MPEG_VIDEO_H264_LOOP_FILTER_BETA controls.
The filter offset controls are signed values in the -6 to 6 range and
are stored into the slice header fields slice_alpha_c0_offset_div2 and
slice_beta_offset_div2. The actual filter offsets FilterOffsetA/B are
double their value, in range of -12 to 12.
Rename variables to more closely match the nomenclature in the H.264
specification.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For micro-mips, srlv inside POOL32A encoding space should use 0x50
sub-opcode, NOT 0x90.
Some early version ISA doc describes the encoding as 0x90 for both srlv and
srav, this looks to me was a typo. I checked Binutils libopcode
implementation which is using 0x50 for srlv and 0x90 for srav.
v1->v2:
- Keep mm_srlv32_op sorted by value.
Fixes: f31318fdf324 ("MIPS: uasm: Add srlv uasm instruction") Cc: Markos Chandras <markos.chandras@imgtec.com> Cc: Paul Burton <paul.burton@mips.com> Cc: linux-mips@vger.kernel.org Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Song Liu <songliubraving@fb.com> Signed-off-by: Jiong Wang <jiong.wang@netronome.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
It was noticed that unbinding and rebinding the KSZ8851 ethernet
resulted in the driver reporting "failed to read device ID" at probe.
Probing the reset line with a 'scope while repeatedly attempting to
bind the driver in a shell loop revealed that the KSZ8851 RSTN pin is
constantly held at zero, meaning the device is held in reset, and
does not respond on the SPI bus.
Experimentation with the startup delay on the regulator set to 50ms
shows that the reset is positively released after 20ms.
Schematics for this board are not available, and the traces are buried
in the inner layers of the board which makes tracing where the RSTN pin
extremely difficult. We can only guess that the RSTN pin is wired to a
reset generator chip driven off the ethernet supply, which fits the
observed behaviour.
Include this delay in the regulator startup delay - effectively
treating the reset as a "supply stable" indicator.
This can not be modelled as a delay in the KSZ8851 driver since the
reset generation is board specific - if the RSTN pin had been wired to
a GPIO, reset could be released earlier via the already provided support
in the KSZ8851 driver.
This also got confirmed by Peter Ujfalusi <peter.ujfalusi@ti.com> based
on Blaze schematics that should be very close to SDP4430:
TPS22902YFPR is used as the regulator switch (gpio48 controlled):
Convert arm boot_lock to raw The VOUT is routed to TPS3808G01DBV.
(SCH Note: Threshold set at 90%. Vsense: 0.405V).
According to the TPS3808 data sheet the RESET delay time when Ct is
open (this is the case in the schema): MIN/TYP/MAX: 12/20/28 ms.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated with notes from schematics from Peter] Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The parameter is still there but it's ignored. We need to check its
value before deciding to go into passthrough mode for AMD IOMMU v2
capable device.
We occasionally use this parameter to force v2 capable device into
translation mode to debug memory corruption that we suspect is
caused by DMA writes.
To address the following comment from Joerg Roedel on the first
version, v2 capability of device is completely ignored.
> This breaks the iommu_v2 use-case, as it needs a direct mapping for the
> devices that support it.
And from Documentation/admin-guide/kernel-parameters.txt:
This option does not override iommu=pt
devm_kstrdup() may return NULL if internal allocation failed.
Thus using label, name is unsafe without checking. Therefor
in the unlikely case of allocation failure, sx150x_probe() simply
returns -ENOMEM.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Fixes: 9e80f9064e73 ("pinctrl: Add SX150X GPIO Extender Pinctrl Driver") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The missed break statement in the outer switch makes the code fall through
always and thus always same value will be printed.
Besides that, compiler warns about missed fall through marker:
drivers/usb/dwc3/./trace.h: In function ‘trace_raw_output_dwc3_log_trb’:
drivers/usb/dwc3/./trace.h:246:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
switch (pcm) {
^~~~~~
Add the missing break statement to work correctly without compilation
warnings.
Fixes: fa8d965d736b ("usb: dwc3: trace: pretty print high-bandwidth transfers too") Cc: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently, When a reserved operation is completed, its entry in the send
queue will not be unreserved, which leads to the miscalculation of
qp->s_avail and thus the triggering of a WARN_ON call trace. This patch
fixes the problem by unreserving the reserved operation when it is
completed.
Fixes: 856cc4c237ad ("IB/hfi1: Add the capability for reserved operations") Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Propagate error code back to userspace if writing the /sys/.../uevent
file fails. Before, the write operation always returned with success,
even if we failed to recognize the input string or if we failed to
generate the uevent itself.
With the error codes properly propagated back to userspace, we are
able to react in userspace accordingly by not assuming and awaiting
a uevent that is not delivered.
Signed-off-by: Peter Rajnoha <prajnoha@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Move the async_synchronize_full call out of __device_release_driver and
into driver_detach.
The idea behind this is that the async_synchronize_full call will only
guarantee that any existing async operations are flushed. This doesn't do
anything to guarantee that a hotplug event that may occur while we are
doing the release of the driver will not be asynchronously scheduled.
By moving this into the driver_detach path we can avoid potential deadlocks
as we aren't holding the device lock at this point and we should not have
the driver we want to flush loaded so the flush will take care of any
asynchronous events the driver we are detaching might have scheduled.
Fixes: 765230b5f084 ("driver-core: add asynchronous probing support for drivers") Reviewed-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com> Reviewed-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
All the audio interfaces on Allwinner SoCs need to change their module
clocks during operation, to switch between support for 44.1 kHz and 48
kHz family sample rates. The clock rate for the module clocks is
governed by their upstream audio PLL. The module clocks themselves only
have a gate, and sometimes a divider or mux. Thus any rate changes need
to be propagated upstream.
Set the CLK_SET_RATE_PARENT flag for all audio module clocks to achieve
this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Fix the issue: device doesn't accept LGO_U1/U2:
1. set SW_U1/U2_ACCEPT_ENABLE to eanble controller to accept LGO_U1/U2
by default;
2. enable/disable controller to initiate requests for transition into
U1/U2 by SW_U1/U2_REQUEST_ENABLE instead of SW_U1/U2_ACCEPT_ENABLE;
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
tk_core.seq is initialized open coded, but that misses to initialize the
lockdep map when lockdep is enabled. Lockdep splats involving tk_core seq
consequently lack a name and are hard to read.
Use the proper initializer which takes care of the lockdep map
initialization.
[ tglx: Massaged changelog ]
Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: peterz@infradead.org Cc: tj@kernel.org Cc: johannes.berg@intel.com Link: https://lkml.kernel.org/r/20181128234325.110011-12-bvanassche@acm.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When initializing a hub we want to give a USB3 port in link training
the same debounce delay time before autosuspening the hub as already
trained, connected enabled ports.
USB3 ports won't reach the enabled state with "current connect status" and
"connect status change" bits set until the USB3 link training finishes.
Catching the port in link training (polling) and adding the debounce delay
prevents unnecessary failed attempts to autosuspend the hub.
Availability of TRB's is calculated using dwc3_calc_trbs_left(), which
determines total available TRB's based on the HWO bit set in a TRB.
In the present code, __dwc3_prepare_one_trb() is called with a TRB which
needs to be prepared for transfer. This __dwc3_prepare_one_trb() calls
dwc3_calc_trbs_left() to determine total available TRBs and set IOC bit
if the total available TRBs are zero. Since the present working TRB (which
is passed as an argument to __dwc3_prepare_one_trb() ) doesn't yet have
the HWO bit set before calling dwc3_calc_trbs_left(), there are chances
that dwc3_calc_trbs_left() wrongly calculates this present working TRB
as free(since the HWO bit is not yet set) and returns the total available
TRBs as greater than zero (including the present working TRB). This could
be a problem.
This patch corrects the above mentioned problem in __dwc3_prepare_one_trb()
by increementing the dep->trb_enqueue at the last (after preparing the TRB)
instead of increementing at the start and setting the IOC bit only if the
total available TRBs returned by dwc3_calc_trbs_left() is 1 . Since we are
increementing the dep->trb_enqueue at the last, the present working TRB is
also considered as available by dwc3_calc_trbs_left() and non zero value is
returned . So, according to the modified logic, when the total available
TRBs is equal to 1 that means the total available TRBs in the pool are 0.
Function smack_key_permission() only issues smack requests for the
following operations:
- KEY_NEED_READ (issues MAY_READ)
- KEY_NEED_WRITE (issues MAY_WRITE)
- KEY_NEED_LINK (issues MAY_WRITE)
- KEY_NEED_SETATTR (issues MAY_WRITE)
A blank smack request is issued in all other cases, resulting in
smack access being granted if there is any rule defined between
subject and object, or denied with -EACCES otherwise.
Request MAY_READ access for KEY_NEED_SEARCH and KEY_NEED_VIEW.
Fix the logic in the unlikely case when both MAY_READ and
MAY_WRITE are needed. Validate access permission field for valid
contents.
Marvell keeps their MMP2 datasheet secret, but there are good clues
that TWSI2 is not on 0xd4025000 on that platform, not does it use
IRQ 58. In fact, the IRQ 58 on MMP2 seems to be a signal processor:
arch/arm/mach-mmp/irqs.h:#define IRQ_MMP2_MSP 58
I'm taking a somewhat educated guess that is probably a copy & paste
error from PXA168 or PXA910 and that the real controller in fact hides
at address 0xd4031000 and uses an interrupt line multiplexed via IRQ 17.
I'm also copying some properties from TWSI1 that were missing or
incorrect.
Tested on a OLPC XO 1.75 machine, where the RTC is on TWSI2.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Tested-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The core ftrace code requires that when it is handed the PC of an
instrumented function, this PC is the address of the instrumented
instruction. This is necessary so that the core ftrace code can identify
the specific instrumentation site. Since the instrumented function will
be a BL, the address of the instrumented function is LR - 4 at entry to
the ftrace code.
This fixup is applied in the mcount_get_pc and mcount_get_pc0 helpers,
which acquire the PC of the instrumented function.
The mcount_get_lr helper is used to acquire the LR of the instrumented
function, whose value does not require this adjustment, and cannot be
adjusted to anything meaningful. No adjustment of this value is made on
other architectures, including arm. However, arm64 adjusts this value by
4.
This patch brings arm64 in line with other architectures and removes the
adjustment of the LR value.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: AKASHI Takahiro <takahiro.akashi@linaro.org> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Torsten Duwe <duwe@suse.de> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There exist very few ap messages which need to have the 'special' flag
enabled. This flag tells the firmware layer to do some pre- and maybe
postprocessing. However, it may happen that this special flag is
enabled but the firmware is unable to deal with this kind of message
and thus returns with reply code 0x41. For example older firmware may
not know the newest messages triggered by the zcrypt device driver and
thus react with reject and the named reply code. Unfortunately this
reply code is not known to the zcrypt error routines and thus default
behavior is to switch the ap queue offline.
This patch now makes the ap error routine aware of the reply code and
so userspace is informed about the bad processing result but the queue
is not switched to offline state any more.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
ce2e6db554fa ("brcmfmac: Add support for getting nvram contents from EFI variables")
we have a device driver accessing the efivars API. Several functions in
the efivars API assume __efivars is set, i.e., that they will be accessed
only after efivars_register() has been called. However, the following NULL
pointer access was reported calling efivar_entry_size() from the brcmfmac
device driver:
Disassembly showed that the local static variable __efivars is NULL,
which is not entirely unexpected given that it is a non-EFI platform.
So add a NULL pointer check to efivar_entry_size(), and to related
functions while at it. In efivars_register() a couple of sanity checks
are added as well.
Reported-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Bhupesh Sharma <bhsharma@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Eric Snowberg <eric.snowberg@oracle.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Julien Thierry <julien.thierry@arm.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Matt Fleming <matt@codeblueprint.co.uk> Cc: Nathan Chancellor <natechancellor@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com> Cc: Sedat Dilek <sedat.dilek@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: YiFei Zhu <zhuyifei1999@gmail.com> Cc: linux-efi@vger.kernel.org Link: http://lkml.kernel.org/r/20181129171230.18699-9-ard.biesheuvel@linaro.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
commit ff140fea847e ("Thermal: handle thermal zone device properly
during system sleep") added PM hook to call thermal zone reset during
sleep. However resetting thermal zone will also clear the passive state
and thus cancel the polling queue which leads the passive cooling device
state not being cleared properly after sleep.
thermal_pm_notify => thermal_zone_device_reset set passive to 0
thermal_zone_trip_update will skip update passive as `old_target ==
instance->target'.
monitor_thermal_zone => thermal_zone_device_set_polling will cancel
tz->poll_queue, so the cooling device state will not be changed
afterwards.
Reported-by: Kame Wang <kamewang@google.com> Signed-off-by: Wei Wang <wvw@google.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
As of commit 6460d3201471 ("arm64: io: Ensure calls to delay routines
are ordered against prior readX()"), MMIO reads smaller than 64 bits
fail to compile under clang because we end up mixing 32-bit and 64-bit
register operands for the same data processing instruction:
./include/asm-generic/io.h:695:9: warning: value size does not match register size specified by the constraint and modifier [-Wasm-operand-widths]
return readb(addr);
^
./arch/arm64/include/asm/io.h:147:58: note: expanded from macro 'readb'
^
./include/asm-generic/io.h:695:9: note: use constraint modifier "w"
./arch/arm64/include/asm/io.h:147:50: note: expanded from macro 'readb'
^
./arch/arm64/include/asm/io.h:118:24: note: expanded from macro '__iormb'
asm volatile("eor %0, %1, %1\n" \
^
Fix the build by casting the macro argument to 'unsigned long' when used
as an input to the inline asm.
Reported-by: Nick Desaulniers <nick.desaulniers@gmail.com> Reported-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
drm_atomic_helper_commit_duplicated_state() sets state->acquire_ctx to
the context given in the argument and leaves it in state after it
quits. The lifetime of state and context are not guaranteed to be the
same, so we shouldn't leave that pointer hanging around. This patch
resets the context to NULL to avoid any oopses.
Changes in v2:
- Added to the set
Suggested-by: Daniel Vetter <daniel@ffwll.ch> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20181129150423.239081-1-sean@poorly.run Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
1) Checkout fresh master Linux branch (tested with commit e195ca6cb)
2) Copy x84_64-config-4.14 to .config, then enable NFS server v4 and build
3) From `kvm-xfstests shell`:
results in NULL dereference in locks_end_grace.
Check that nfsd has been started before trying to end the grace period.
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
of_find_node_by_path() acquires a reference to the node returned by it
and that reference needs to be dropped by its caller. soc_is_brcmstb()
doesn't do that, so fix it.
[treding: slightly rewrite to avoid inline comparison]
Fixes: d52fad262041 ("soc: add stubs for brcmstb SoC's") Signed-off-by: Yangtao Li <tiny.windzz@gmail.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A relatively standard idiom for ensuring that a pair of MMIO writes to a
device arrive at that device with a specified minimum delay between them
is as follows:
the intention being that the read-back from the device will push the
prior write to CTL1, and the udelay will hold up the write to CTL1 until
at least 10us have elapsed.
Unfortunately, on arm64 where the underlying delay loop is implemented
as a read of the architected counter, the CPU does not guarantee
ordering from the readl() to the delay loop and therefore the delay loop
could in theory be speculated and not provide the desired interval
between the two writes.
Fix this in a similar manner to PowerPC by introducing a dummy control
dependency on the output of readX() which, combined with the ISB in the
read of the architected counter, guarantees that a subsequent delay loop
can not be executed until the readX() has returned its result.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Add support for the IIC code for the r8a77990 (R-Car E3).
It is not considered compatible with existing fallback bindings
due to the documented absence of automatic transmission registers.
These registers are currently not used by the driver and
thus the provides the same behaviour for "renesas,iic-r8a77990" and
"renesas,rcar-gen3-iic". The point of declaring incompatibility is
to allow for automatic transmission register support to be added to
"renesas,iic-r8a77990" and "renesas,rcar-gen3-iic" in future.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When call f2fs_acl_create_masq() failed, the caller f2fs_acl_create()
should return -EIO instead of -ENOMEM, this patch makes it consistent
with posix_acl_create() which has been fixed in commit beaf226b863a
("posix_acl: don't ignore return value of posix_acl_create_masq()").
Fixes: 83dfe53c185e ("f2fs: fix reference leaks in f2fs_acl_create") Signed-off-by: Tiezhu Yang <kernelpatch@126.com> Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The v4l2_dv_timings_cap struct is used to do sanity checks when setting and
enumerating DV timings, ensuring that only valid timings as per the HW
capabilities are allowed.
However, many drivers just filled in 0 for the minimum width, height or
pixelclock frequency. This can cause timings with e.g. 0 as width and height
to be accepted, which will in turn lead to a potential division by zero.
Fill in proper values are minimum boundaries. 640x350 was chosen since it is
the smallest resolution in v4l2-dv-timings.h. Same for 13 MHz as the lowest
pixelclock frequency (it's slightly below the minimum of 13.5 MHz in the
v4l2-dv-timings.h header).
Various 2-in-1's use KIOX010A and KIOX020A as HIDs for 2 KXCJ91008
accelerometers. The KIOX010A HID is for the one in the base and the
KIOX020A for the accelerometer in the keyboard.
Since userspace does not have a way yet to deal with (or ignore) the
accelerometer in the keyboard, this commit just adds the KIOX010A HID
for now so that display rotation will work.
Related: https://github.com/hadess/iio-sensor-proxy/issues/166 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Before this patch we are registering the internal clocks (for example on
Meson8b, where the SAR ADC IP block implements the divider and gate
clocks) with the following names:
- /soc/cbus@c1100000/adc@8680#adc_div
- /soc/cbus@c1100000/adc@8680#adc_en
This is bad because the common clock framework uses the clock to create
a directory in <debugfs>/clk. With such name, the directory creation
(silently) fails and the debugfs entry ends up being created at the
debugfs root.
With this change, the new clock names are:
- c1108680.adc#adc_div
- c1108680.adc#adc_en
This matches the clock naming scheme used in the PWM, Ethernet and MMC
drivers. It also fixes the problem with debugfs.
The idea is shamelessly taken from commit b96e9eb62841c5 ("pwm: meson:
Fix mux clock names").
Fixes: 3921db46a8c5bc ("iio: Convert to using %pOF instead of full_name") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
devm_kasprintf() may return NULL on failure of internal allocation thus
the assignments to init.name are not safe if not checked. On error
meson_sar_adc_clk_init() returns negative values so -ENOMEM in the
(unlikely) failure case of devm_kasprintf() should be fine here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Fixes: 3adbf3427330 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs") Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
drivers/dma/xilinx/zynqmp_dma.c:166:4: warning: attribute 'aligned' is
ignored, place it after "struct" to apply attribute to type declaration
[-Wignored-attributes]
}; __aligned(64)
^
./include/linux/compiler_types.h:200:38: note: expanded from macro
'__aligned'
^
1 warning generated.
As Nick pointed out in the previous version of this patch, the author
likely intended for this struct to be 8-byte (64-bit) aligned, not
64-byte, which is the default. Remove the hanging __aligned attribute.
drivers/ptp/ptp_clock.c:298 ptp_clock_register() warn:
passing zero to 'ERR_PTR'
'err' should be set while device_create_with_groups and
pps_register_source fails
Fixes: 85a66e550195 ("ptp: create "pins" together with the rest of attributes") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
of_parse_phandle() returns the device node with refcount incremented.
There are two nodes that are used temporary in mtk_vcodec_init_enc_pm(),
but their refcounts are not decremented.
The patch adds one of_node_put() and fixes returning error codes.
Found by Linux Driver Verification project (linuxtesting.org).
of_find_node_by_path() acquires a reference to the node returned by it
and that reference needs to be dropped by its caller. soc_is_tegra()
doesn't do that, so fix it.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com> Acked-by: Jon Hunter <jonathanh@nvidia.com>
[treding: slightly rewrite to avoid inline comparison] Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The tool perf is useful for the performance analysis on the Hygon Dhyana
platform. But right now there is no Hygon support for it to analyze the
KVM guest os data. So add Hygon Dhyana support to it by checking vendor
string to share the code path of AMD.
Signed-off-by: Pu Wen <puwen@hygon.cn> Acked-by: Borislav Petkov <bp@suse.de> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1542008451-31735-1-git-send-email-puwen@hygon.cn Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If an ARM mapping symbol shares an address with a valid symbol,
find_elf_symbol can currently return the mapping symbol instead, as the
symbol is not validated. This can result in confusing warnings:
WARNING: vmlinux.o(.text+0x18f4028): Section mismatch in reference
from the function set_reset_devices() to the variable .init.text:$x.0
This change adds a call to is_valid_name to find_elf_symbol, similarly
to how it's already used in find_elf_symbol2.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently the cpu affinity hint mask for completion EQs is stored and
read from the wrong place, since reading and storing is done from the
same index, there is no actual issue with that, but internal irq_info
for completion EQs stars at MLX5_EQ_VEC_COMP_BASE offset in irq_info
array, this patch changes the code to use the correct offset to store
and read the IRQ affinity hint.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When building the kernel with Clang, the following section mismatch
warnings appears:
WARNING: vmlinux.o(.text+0x2d398): Section mismatch in reference from
the function _setup() to the function .init.text:_setup_iclk_autoidle()
The function _setup() references
the function __init _setup_iclk_autoidle().
This is often because _setup lacks a __init
annotation or the annotation of _setup_iclk_autoidle is wrong.
WARNING: vmlinux.o(.text+0x2d3a0): Section mismatch in reference from
the function _setup() to the function .init.text:_setup_reset()
The function _setup() references
the function __init _setup_reset().
This is often because _setup lacks a __init
annotation or the annotation of _setup_reset is wrong.
WARNING: vmlinux.o(.text+0x2d408): Section mismatch in reference from
the function _setup() to the function .init.text:_setup_postsetup()
The function _setup() references
the function __init _setup_postsetup().
This is often because _setup lacks a __init
annotation or the annotation of _setup_postsetup is wrong.
_setup is used in omap_hwmod_allocate_module, which isn't marked __init
and looks like it shouldn't be, meaning to fix these warnings, those
functions must be moved out of the init section, which this patch does.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Some of the functions (like cdn_dp_dpcd_read, cdn_dp_get_edid_block)
allow to read 64KiB, but the cdn_dp_mailbox_read_receive, that is
used by them, can read only up to 255 bytes at once. Normally, it's
not a big issue as DPCD or EDID reads won't (hopefully) exceed that
value.
The real issue here is the revocation list read during the HDCP
authentication process. (problematic use case:
https://chromium.googlesource.com/chromiumos/third_party/kernel/+/chromeos-4.4/drivers/gpu/drm/rockchip/cdn-dp-reg.c#1152)
The list can reach 127*5+4 bytes (num devs * 5 bytes per ID/Bksv +
4 bytes of an additional info).
In other words - CTSes with HDCP Repeater won't pass without this
fix. Oh, and the driver will most likely stop working (best case
scenario).
The smsc95xx driver already takes into account the NET_IP_ALIGN
parameter when setting up the receive packet data, which means
we do not need to worry about aligning the packets in the usbnet
driver.
Adding the EVENT_NO_IP_ALIGN means that the IPv4 header is now
passed to the ip_rcv() routine with the start on an aligned address.
Tested on Raspberry Pi B3.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>