Commands that are reset are returned with status
SAM_STAT_COMMAND_TERMINATED. PVSCSI currently returns DID_OK |
SAM_STAT_COMMAND_TERMINATED which fails the command. Instead, set hostbyte
to DID_RESET to allow upper layers to retry.
Tested by copying a large file between two pvscsi disks on same adapter
while performing a bus reset at 1-second intervals. Before fix, commands
sometimes fail with DID_OK. After fix, commands observed to fail with
DID_RESET.
Signed-off-by: Jim Gill <jgill@vmware.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
KASAN reports a use-after-free in fcoe_ctlr_els_send() when we're sending a
LOGO and have FIP debugging enabled. This is because we're first freeing
the skb and then printing the frame's DID. But the DID is a member of the
FC frame header which in turn is the skb's payload.
Exchange the debug print and kfree_skb() calls so we're not touching the
freed data.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
On some systems using edge triggered ACPI Event Interrupts, the initial
state at boot is not setup by the firmware, instead relying on the edge
irq event handler running at least once to setup the initial state.
2 known examples of this are:
1) The Surface 3 has its _LID state controlled by an ACPI operation region
triggered by a GPIO event:
Method (_E4C, 0, Serialized) // _Exx: Edge-Triggered GPE
{
If ((HELD == One))
{
^^LID.LIDB = One
}
Else
{
^^LID.LIDB = Zero
Notify (LID, 0x80) // Status Change
}
Notify (^^PCI0.SPI1.NTRG, One) // Device Check
}
Currently, the state of LIDB is wrong until the user actually closes or
open the cover. We need to trigger the GPIO event once to update the
internal ACPI state.
Coincidentally, this also enables the Surface 2 integrated HID sensor hub
which also requires an ACPI gpio operation region to start initialization.
2) Various Bay Trail based tablets come with an external USB mux and
TI T1210B USB phy to enable USB gadget mode. The mux is controlled by a
GPIO which is controlled by an edge triggered ACPI Event Interrupt which
monitors the micro-USB ID pin.
When the tablet is connected to a PC (or no cable is plugged in), the ID
pin is high and the tablet should be in gadget mode. But the GPIO
controlling the mux is initialized by the firmware so that the USB data
lines are muxed to the host controller.
This means that if the user wants to use gadget mode, the user needs to
first plug in a host-cable to force the ID pin low and then unplug it
and connect the tablet to a PC, to get the ACPI event handler to run and
switch the mux to device mode,
This commit fixes both by running the event-handler once on boot.
Note that the running of the event-handler is done from a late_initcall,
this is done because the handler AML code may rely on OperationRegions
registered by other builtin drivers. This avoids errors like these:
[ 0.133026] ACPI Error: No handler for Region [XSCG] ((____ptrval____)) [GenericSerialBus] (20180531/evregion-132)
[ 0.133036] ACPI Error: Region GenericSerialBus (ID=9) has no handler (20180531/exfldio-265)
[ 0.133046] ACPI Error: Method parse/execution failed \_SB.GPO2._E12, AE_NOT_EXIST (20180531/psparse-516)
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
[hdegoede: Document BYT USB mux reliance on initial trigger]
[hdegoede: Run event handler from a late_initcall, rather then immediately] Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In case of memcg_online_kmem() failure, memcg_cgroup::id remains hashed
in mem_cgroup_idr even after memcg memory is freed. This leads to leak
of ID in mem_cgroup_idr.
This patch adds removal into mem_cgroup_css_alloc(), which fixes the
problem. For better readability, it adds a generic helper which is used
in mem_cgroup_alloc() and mem_cgroup_id_put_many() as well.
Link: http://lkml.kernel.org/r/152354470916.22460.14397070748001974638.stgit@localhost.localdomain
Fixes 73f576c04b94 ("mm: memcontrol: fix cgroup creation failure after many small jobs") Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: Michal Hocko <mhocko@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Current value for a target abort error is 0x010, however, this value
should in fact be 0x002. As it stands, the range of error is 0..7 so
it is currently never being detected. This bug has been in the driver
since the early 2.6.12 days (or before).
Detected by CoverityScan, CID#744290 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Delete the old VM_BUG_ON_VMA() from zap_pmd_range(), which asserted
that mmap_sem must be held when splitting an "anonymous" vma there.
Whether that's still strictly true nowadays is not entirely clear,
but the danger of sometimes crashing on the BUG is now fairly clear.
Even with the new stricter rules for anonymous vma marking, the
condition it checks for can possible trigger. Commit 44960f2a7b63
("staging: ashmem: Fix SIGBUS crash when traversing mmaped ashmem
pages") is good, and originally I thought it was safe from that
VM_BUG_ON_VMA(), because the /dev/ashmem fd exposed to the user is
disconnected from the vm_file in the vma, and madvise(,,MADV_REMOVE)
insists on VM_SHARED.
But after I read John's earlier mail, drawing attention to the
vfs_fallocate() in there: I may be wrong, and I don't know if Android
has THP in the config anyway, but it looks to me like an
unmap_mapping_range() from ashmem's vfs_fallocate() could hit precisely
the VM_BUG_ON_VMA(), once it's vma_is_anonymous().
Signed-off-by: Hugh Dickins <hughd@google.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Kirill Shutemov <kirill.shutemov@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In commit ab123fe071c9 ("enic: handle mtu change for vf properly")
ASSERT_RTNL() is added to _enic_change_mtu() to prevent it from being
called without rtnl held. enic_probe() calls enic_change_mtu()
without rtnl held. At this point netdev is not registered yet.
Remove call to enic_change_mtu and assign the mtu to netdev->mtu.
Fixes: ab123fe071c9 ("enic: handle mtu change for vf properly") Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This is necessary to be able to include <linux/msi.h> when
CONFIG_GENERIC_MSI_IRQ_DOMAIN is enabled. Without this, a build with
CONFIG_GENERIC_MSI_IRQ_DOMAIN fails with:
In file included from drivers//ata/ahci.c:45:0:
>> include/linux/msi.h:226:10: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
msi_alloc_info_t *arg);
^~~~~~~~~~~~~~~~
sg_alloc_fn
include/linux/msi.h:230:9: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
msi_alloc_info_t *arg);
^~~~~~~~~~~~~~~~
sg_alloc_fn
include/linux/msi.h:239:12: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
msi_alloc_info_t *arg);
^~~~~~~~~~~~~~~~
sg_alloc_fn
include/linux/msi.h:240:22: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
void (*msi_finish)(msi_alloc_info_t *arg, int retval);
^~~~~~~~~~~~~~~~
sg_alloc_fn
include/linux/msi.h:241:20: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
void (*set_desc)(msi_alloc_info_t *arg,
^~~~~~~~~~~~~~~~
sg_alloc_fn
include/linux/msi.h:316:18: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
int nvec, msi_alloc_info_t *args);
^~~~~~~~~~~~~~~~
sg_alloc_fn
include/linux/msi.h:318:29: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
int virq, int nvec, msi_alloc_info_t *args);
^~~~~~~~~~~~~~~~
sg_alloc_fn
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Code that was added to force gcc not to inline any function that isn't
explicitly declared as inline uncovered that init_tick_ops() isn't
marked as "__init". It is only called by __init functions and more
importantly it too calls an __init function which would require it to be
__init as well.
Link: http://lkml.kernel.org/r/201806060444.hdHcKOBy%fengguang.wu@intel.com Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
../arch/arc/mm/cache.c: In function 'flush_anon_page':
../arch/arc/mm/cache.c:1062:55: warning: passing argument 2 of '__flush_dcache_page' makes integer from pointer without a cast [-Wint-conversion]
__flush_dcache_page((phys_addr_t)page_address(page), page_address(page));
^~~~~~~~~~~~~~~~~~
../arch/arc/mm/cache.c:1013:59: note: expected 'long unsigned int' but argument is of type 'void *'
void __flush_dcache_page(phys_addr_t paddr, unsigned long vaddr)
~~~~~~~~~~~~~~^~~~~
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: linux-snps-arc@lists.infradead.org Cc: Elad Kanfi <eladkan@mellanox.com> Cc: Leon Romanovsky <leonro@mellanox.com> Cc: Ofer Levi <oferle@mellanox.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Fix build errors in arch/arc/'s delay.h:
- add "extern unsigned long loops_per_jiffy;"
- add <asm-generic/types.h> for "u64"
In file included from ../drivers/infiniband/hw/cxgb3/cxio_hal.c:32:
../arch/arc/include/asm/delay.h: In function '__udelay':
../arch/arc/include/asm/delay.h:61:12: error: 'u64' undeclared (first use in this function)
loops = ((u64) usecs * 4295 * HZ * loops_per_jiffy) >> 32;
^~~
In file included from ../drivers/infiniband/hw/cxgb3/cxio_hal.c:32:
../arch/arc/include/asm/delay.h: In function '__udelay':
../arch/arc/include/asm/delay.h:63:37: error: 'loops_per_jiffy' undeclared (first use in this function)
loops = ((u64) usecs * 4295 * HZ * loops_per_jiffy) >> 32;
^~~~~~~~~~~~~~~
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: linux-snps-arc@lists.infradead.org Cc: Elad Kanfi <eladkan@mellanox.com> Cc: Leon Romanovsky <leonro@mellanox.com> Cc: Ofer Levi <oferle@mellanox.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Fix printk format warning in arch/arc/plat-eznps/mtm.c:
In file included from ../include/linux/printk.h:7,
from ../include/linux/kernel.h:14,
from ../include/linux/list.h:9,
from ../include/linux/smp.h:12,
from ../arch/arc/plat-eznps/mtm.c:17:
../arch/arc/plat-eznps/mtm.c: In function 'set_mtm_hs_ctr':
../include/linux/kern_levels.h:5:18: warning: format '%d' expects argument of type 'int', but argument 2 has type 'long int' [-Wformat=]
#define KERN_SOH "\001" /* ASCII Start Of Header */
^~~~~~
../include/linux/kern_levels.h:11:18: note: in expansion of macro 'KERN_SOH'
#define KERN_ERR KERN_SOH "3" /* error conditions */
^~~~~~~~
../include/linux/printk.h:308:9: note: in expansion of macro 'KERN_ERR'
printk(KERN_ERR pr_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~
../arch/arc/plat-eznps/mtm.c:166:3: note: in expansion of macro 'pr_err'
pr_err("** Invalid @nps_mtm_hs_ctr [%d] needs to be [%d:%d] (incl)\n",
^~~~~~
../arch/arc/plat-eznps/mtm.c:166:40: note: format string is defined here
pr_err("** Invalid @nps_mtm_hs_ctr [%d] needs to be [%d:%d] (incl)\n",
~^
%ld
The hs_ctr variable can just be int instead of long, so also change
kstrtol() to kstrtoint() and leave the format string as %d.
Also add 2 header files since they are used in mtm.c and we prefer
not to depend on accidental/indirect #includes.
Cc: linux-snps-arc@lists.infradead.org Cc: Ofer Levi <oferle@mellanox.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Add <linux/types.h> to fix build errors.
Both ctop.h and <soc/nps/common.h> use u32 types and cause many
errors.
Examples:
../include/soc/nps/common.h:71:4: error: unknown type name 'u32'
u32 __reserved:20, cluster:4, core:4, thread:4;
../include/soc/nps/common.h:76:3: error: unknown type name 'u32'
u32 value;
../include/soc/nps/common.h:124:4: error: unknown type name 'u32'
u32 base:8, cl_x:4, cl_y:4,
../include/soc/nps/common.h:127:3: error: unknown type name 'u32'
u32 value;
../arch/arc/plat-eznps/include/plat/ctop.h:83:4: error: unknown type name 'u32'
u32 gen:1, gdis:1, clk_gate_dis:1, asb:1,
../arch/arc/plat-eznps/include/plat/ctop.h:86:3: error: unknown type name 'u32'
u32 value;
../arch/arc/plat-eznps/include/plat/ctop.h:93:4: error: unknown type name 'u32'
u32 csa:22, dmsid:6, __reserved:3, cs:1;
../arch/arc/plat-eznps/include/plat/ctop.h:95:3: error: unknown type name 'u32'
u32 value;
Cc: linux-snps-arc@lists.infradead.org Cc: Ofer Levi <oferle@mellanox.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Function nfp_flower_repr_get_type_and_port expects an enum nfp_repr_type
return value but, if the repr type is unknown, returns a value of type
enum nfp_flower_cmsg_port_type. This means that if FW encodes the port
ID in a way the driver does not understand instead of dropping the frame
driver may attribute it to a physical port (uplink) provided the port
number is less than physical port count.
Fix this and ensure a net_device of NULL is returned if the repr can not
be determined.
Fixes: 1025351a88a4 ("nfp: add flower app") Signed-off-by: John Hurley <john.hurley@netronome.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
As for today we don't setup SMP_CACHE_BYTES and cache_line_size for
ARC, so they are set to L1_CACHE_BYTES by default. L1 line length
(L1_CACHE_BYTES) might be easily smaller than L2 line (which is
usually the case BTW). This breaks code.
For example this breaks ethernet infrastructure on HSDK/AXS103 boards
with IOC disabled, involving manual cache flushes
Functions which alloc and manage sk_buff packet data area rely on
SMP_CACHE_BYTES define. In the result we can share last L2 cache
line in sk_buff linear packet data area between DMA buffer and
some useful data in other structure. So we can lose this data when
we invalidate DMA buffer.
sk_buff linear packet data area
|
|
| skb->end skb->tail
V | |
V V
----------------------------------------------.
packet data | <tail padding> | <useful data in other struct>
----------------------------------------------.
---------------------.--------------------------------------------------.
SLC line | SLC (L2 cache) line (128B) |
---------------------.--------------------------------------------------.
^ ^
| |
These cache lines will be invalidated when we invalidate skb
linear packet data area before DMA transaction starting.
This leads to issues painful to debug as it reproduces only if
(sk_buff->end - sk_buff->tail) < SLC_LINE_SIZE and
if we have some useful data right after sk_buff->end.
Fix that by hardcode SMP_CACHE_BYTES to max line length we may have.
This fixes the reported family on modern AMD processors (e.g. Ryzen,
which is family 0x17). Previously these processors all showed up as
family 0xf.
See the document
https://support.amd.com/TechDocs/56255_OSRR.pdf
section CPUID_Fn00000001_EAX for how to calculate the family
from the BaseFamily and ExtFamily values.
This matches the code in arch/x86/lib/cpu.c
Signed-off-by: Calvin Walton <calvin.walton@kepstin.ca> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
/sys/../zswap/stored_pages keeps rising in a zswap test with
"zswap.max_pool_percent=0" parameter. But it should not compress or
store pages any more since there is no space in the compressed pool.
Reproduce steps:
1. Boot kernel with "zswap.enabled=1"
2. Set the max_pool_percent to 0
# echo 0 > /sys/module/zswap/parameters/max_pool_percent
3. Do memory stress test to see if some pages have been compressed
# stress --vm 1 --vm-bytes $mem_available"M" --timeout 60s
4. Watching the 'stored_pages' number increasing or not
The root cause is:
When zswap_max_pool_percent is set to 0 via kernel parameter,
zswap_is_full() will always return true due to zswap_shrink(). But if
the shinking is able to reclain a page successfully the code then
proceeds to compressing/storing another page, so the value of
stored_pages will keep changing.
To solve the issue, this patch adds a zswap_is_full() check again after
zswap_shrink() to make sure it's now under the max_pool_percent, and to
not compress/store if we reached the limit.
Link: http://lkml.kernel.org/r/20180530103936.17812-1-liwang@redhat.com Signed-off-by: Li Wang <liwang@redhat.com> Acked-by: Dan Streetman <ddstreet@ieee.org> Cc: Seth Jennings <sjenning@redhat.com> Cc: Huang Ying <huang.ying.caritas@gmail.com> Cc: Yu Zhao <yuzhao@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In order for load/store tearing prevention to work, _all_ accesses to
the variable in question need to be done around READ and WRITE_ONCE()
macros. Ensure everyone does so for q->status variable for
semtimedop().
Dirk Gouders reported that two consecutive "make" invocations on an
already compiled tree will show alternating behaviors:
$ make
CALL scripts/checksyscalls.sh
DESCEND objtool
CHK include/generated/compile.h
DATAREL arch/x86/boot/compressed/vmlinux
Kernel: arch/x86/boot/bzImage is ready (#48)
Building modules, stage 2.
MODPOST 165 modules
$ make
CALL scripts/checksyscalls.sh
DESCEND objtool
CHK include/generated/compile.h
LD arch/x86/boot/compressed/vmlinux
ZOFFSET arch/x86/boot/zoffset.h
AS arch/x86/boot/header.o
LD arch/x86/boot/setup.elf
OBJCOPY arch/x86/boot/setup.bin
OBJCOPY arch/x86/boot/vmlinux.bin
BUILD arch/x86/boot/bzImage
Setup is 15644 bytes (padded to 15872 bytes).
System is 6663 kB
CRC 3eb90f40
Kernel: arch/x86/boot/bzImage is ready (#48)
Building modules, stage 2.
MODPOST 165 modules
He bisected it back to:
commit 98f78525371b ("x86/boot: Refuse to build with data relocations")
The root cause was the use of the "if_changed" kbuild function multiple
times for the same target. It was designed to only be used once per
target, otherwise it will effectively always trigger, flipping back and
forth between the two commands getting recorded by "if_changed". Instead,
this patch merges the two commands into a single function to get stable
build artifacts (i.e. .vmlinux.cmd), and a single build behavior.
NO_RT_RUNTIME_SHARE feature is used to prevent a CPU borrow enough
runtime with a spin-rt-task.
However, if RT_RUNTIME_SHARE feature is enabled and rt_rq has borrowd
enough rt_runtime at the beginning, rt_runtime can't be restored to
its initial bandwidth rt_runtime after we disable RT_RUNTIME_SHARE.
E.g. on my PC with 4 cores, procedure to reproduce:
1) Make sure RT_RUNTIME_SHARE is enabled
cat /sys/kernel/debug/sched_features
GENTLE_FAIR_SLEEPERS START_DEBIT NO_NEXT_BUDDY LAST_BUDDY
CACHE_HOT_BUDDY WAKEUP_PREEMPTION NO_HRTICK NO_DOUBLE_TICK
LB_BIAS NONTASK_CAPACITY TTWU_QUEUE NO_SIS_AVG_CPU SIS_PROP
NO_WARN_DOUBLE_CLOCK RT_PUSH_IPI RT_RUNTIME_SHARE NO_LB_MIN
ATTACH_AGE_LOAD WA_IDLE WA_WEIGHT WA_BIAS
2) Start a spin-rt-task
./loop_rr &
3) set affinity to the last cpu
taskset -p 8 $pid_of_loop_rr
4) Observe that last cpu have borrowed enough runtime.
cat /proc/sched_debug | grep rt_runtime
.rt_runtime : 950.000000
.rt_runtime : 900.000000
.rt_runtime : 950.000000
.rt_runtime : 1000.000000
5) Disable RT_RUNTIME_SHARE
echo NO_RT_RUNTIME_SHARE > /sys/kernel/debug/sched_features
6) Observe that rt_runtime can not been restored
cat /proc/sched_debug | grep rt_runtime
.rt_runtime : 950.000000
.rt_runtime : 900.000000
.rt_runtime : 950.000000
.rt_runtime : 1000.000000
This patch help to restore rt_runtime after we disable
RT_RUNTIME_SHARE.
Signed-off-by: Hailong Liu <liu.hailong6@zte.com.cn> Signed-off-by: Jiang Biao <jiang.biao2@zte.com.cn> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: zhong.weidong@zte.com.cn Link: http://lkml.kernel.org/r/1531874815-39357-1-git-send-email-liu.hailong6@zte.com.cn Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Rx hash/filter table configuration uses rss_conf_obj to configure filters
in the hardware. This object is initialized only when the interface is
brought up.
This patch adds driver changes to configure rss params only when the device
is in opened state. In port disabled case, the config will be cached in the
driver structure which will be applied in the successive load path.
Please consider applying it to 'net' branch.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Including asm/cacheflush.h first results in the following build error
when trying to build sparc32:allmodconfig, because 'struct page' has not
been declared, and the function declaration ends up creating a separate
(private) declaration of struct page (as a result of function arguments
being in the scope of the function declaration and definition, not in
global scope).
The C scoping rules do not just affect variable visibility, they also
affect type declaration visibility.
The end result is that when the actual call site is seen in
<linux/highmem.h>, the 'struct page' type in the caller is not the same
'struct page' that the function was declared with, resulting in:
In file included from arch/sparc/include/asm/page.h:10:0,
...
from drivers/staging/media/omap4iss/iss_video.c:15:
include/linux/highmem.h: In function 'clear_user_highpage':
include/linux/highmem.h:137:31: error:
passing argument 1 of 'sparc_flush_page_to_ram' from incompatible
pointer type
Include generic includes files first to fix the problem.
Fixes: fc96d58c10162 ("[media] v4l: omap4iss: Add support for OMAP4 camera interface - Video devices") Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: David S. Miller <davem@davemloft.net> Cc: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[ Added explanation of C scope rules - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
of_iomap() can return NULL so that return needs to be checked and NULL
treated as failure. While at it also take care of the missing
of_node_put() in the error path.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Fixes: commit afa17a500a36 ("net/can: add driver for mscan family & mpc52xx_mscan") Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Prevent drivers from building on PPC32 if they use isa_bus_to_virt(),
isa_virt_to_bus(), or isa_page_to_bus(), which are not available and
thus cause build errors.
../drivers/net/ethernet/3com/3c515.c: In function 'corkscrew_open':
../drivers/net/ethernet/3com/3c515.c:824:9: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
../drivers/net/ethernet/amd/lance.c: In function 'lance_rx':
../drivers/net/ethernet/amd/lance.c:1203:23: error: implicit declaration of function 'isa_bus_to_virt'; did you mean 'bus_to_virt'? [-Werror=implicit-function-declaration]
../drivers/net/ethernet/amd/ni65.c: In function 'ni65_init_lance':
../drivers/net/ethernet/amd/ni65.c:585:20: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
../drivers/net/ethernet/cirrus/cs89x0.c: In function 'net_open':
../drivers/net/ethernet/cirrus/cs89x0.c:897:20: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Suggested-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The bad access is in neigh_hh_output(), at skb->data - 16 (HH_DATA_MOD).
atl1c driver provided skb with no headroom, so 14 bytes (ethernet
header) got pulled, but then 16 are copied.
Reserve NET_SKB_PAD bytes headroom, like netdev_alloc_skb().
Compile tested only; I lack hardware.
Fixes: 7b7017642199 ("atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring") Signed-off-by: Florian Westphal <fw@strlen.de> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
There's a possible race where driver can read link status in mid-transition
and see that virtual-link is up yet speed is 0. Since in this
mid-transition we're guaranteed to see a mailbox from MFW soon, we can
afford to treat this as link down.
Fixes: cc875c2e ("qed: Add link support") Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Apparently, MFW publishes EEE capabilities even for Fiber-boards that don't
support them, and later since qed internally sets adv_caps it would cause
link-flap avoidance (LFA) to fail when driver would initiate the link.
This in turn delays the link, causing traffic to fail.
Driver has been modified to not to ask MFW for any EEE config if EEE isn't
to be enabled.
Fixes: 645874e5 ("qed: Add support for Energy efficient ethernet.") Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Do not expose the address of vmx->nested.current_vmptr to
kvm_write_guest_virt_system() as the resulting __copy_to_user()
call will trigger a WARN when CONFIG_HARDENED_USERCOPY is
enabled.
Opportunistically clean up variable names in handle_vmptrst()
to improve readability, e.g. vmcs_gva is misleading as the
memory operand of VMPTRST is plain memory, not a VMCS.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Tested-by: Peter Shier <pshier@google.com> Reviewed-by: Peter Shier <pshier@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Its possible to rename two chains to the same name in one
transaction:
nft add chain t c1
nft add chain t c2
nft 'rename chain t c1 c3;rename chain t c2 c3'
This creates two chains named 'c3'.
Appears to be harmless, both chains can still be deleted both
by name or handle, but, nevertheless, its a bug.
Walk transaction log and also compare vs. the pending renames.
Both chains can still be deleted, but nevertheless it is a bug as
we don't allow to create chains with identical names, so we should
prevent this from happening-by-rename too.
Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The new name is stored in the transaction metadata, on commit,
the pointers to the old and new names are swapped.
Therefore in abort and commit case we have to free the
pointer in the chain_trans container.
In commit case, the pointer can be used by another cpu that
is currently dumping the renamed chain, thus kfree needs to
happen after waiting for rcu readers to complete.
Fixes: b7263e071a ("netfilter: nf_tables: Allow chain name of up to 255 chars") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
None of the JITs is allowed to implement exit paths from the BPF
insn mappings other than BPF_JMP | BPF_EXIT. In the BPF core code
we have a couple of rewrites in eBPF (e.g. LD_ABS / LD_IND) and
in eBPF to cBPF translation to retain old existing behavior where
exceptions may occur; they are also tightly controlled by the
verifier where it disallows some of the features such as BPF to
BPF calls when legacy LD_ABS / LD_IND ops are present in the BPF
program. During recent review of all BPF_XADD JIT implementations
I noticed that the ppc64 one is buggy in that it contains two
jumps to exit paths. This is problematic as this can bypass verifier
expectations e.g. pointed out in commit f6b1b3bf0d5f ("bpf: fix
subprog verifier bypass by div/mod by 0 exception"). The first
exit path is obsoleted by the fix in ca36960211eb ("bpf: allow xadd
only on aligned memory") anyway, and for the second one we need to
do a fetch, add and store loop if the reservation from lwarx/ldarx
was lost in the meantime.
Fixes: 156d0e290e96 ("powerpc/ebpf/jit: Implement JIT compiler for extended BPF") Reviewed-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Reviewed-by: Sandipan Das <sandipan@linux.vnet.ibm.com> Tested-by: Sandipan Das <sandipan@linux.vnet.ibm.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
GC of set uses call_rcu() to destroy elements.
So that elements would be destroyed after destroying sets and chains.
But, elements should be destroyed before destroying sets and chains.
In order to wait calling call_rcu(), a rcu_barrier() is added.
In order to test correctly, below patch should be applied.
https://patchwork.ozlabs.org/patch/940883/
The list [1] of commits doing endianness fixes in USB subsystem is long
due to below quote from USB spec Revision 2.0 from April 27, 2000:
------------
8.1 Byte/Bit Ordering
Multiple byte fields in standard descriptors, requests, and responses
are interpreted as and moved over the bus in little-endian order, i.e.
LSB to MSB.
------------
This commit belongs to the same family.
[1] Example of endianness fixes in USB subsystem:
commit 14e1d56cbea6 ("usb: gadget: f_uac2: endianness fixes.")
commit 42370b821168 ("usb: gadget: f_uac1: endianness fixes.")
commit 63afd5cc7877 ("USB: chaoskey: fix Alea quirk on big-endian hosts")
commit 74098c4ac782 ("usb: gadget: acm: fix endianness in notifications")
commit cdd7928df0d2 ("ACM gadget: fix endianness in notifications")
commit 323ece54e076 ("cdc-wdm: fix endianness bug in debug statements")
commit e102609f1072 ("usb: gadget: uvc: Fix endianness mismatches")
list goes on
Fixes: 132fcb460839 ("usb: gadget: Add Audio Class 2.0 Driver") Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Ruslan Bilovol <ruslan.bilovol@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The tools/usb/ffs-test.c file defines cpu_to_le16/32 by using the C
library htole16/32 function calls. However, cpu_to_le16/32 are used when
initializing structures, i.e in a context where a function call is not
allowed.
It works fine on little endian systems because htole16/32 are defined by
the C library as no-ops. But on big-endian systems, they are actually
doing something, which might involve calling a function, causing build
failures, such as:
ffs-test.c:48:25: error: initializer element is not constant
#define cpu_to_le32(x) htole32(x)
^~~~~~~
ffs-test.c:128:12: note: in expansion of macro ‘cpu_to_le32’
.magic = cpu_to_le32(FUNCTIONFS_DESCRIPTORS_MAGIC_V2),
^~~~~~~~~~~
To solve this, we code cpu_to_le16/32 in a way that allows them to be
used when initializing structures. This fix was imported from
meta-openembedded/android-tools/fix-big-endian-build.patch written by
Thomas Petazzoni <thomas.petazzoni@free-electrons.com>.
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Fix build errors when built for PPC64:
These variables are only used on PPC32 so they don't need to be
initialized for PPC64.
../drivers/usb/phy/phy-fsl-usb.c: In function 'usb_otg_start':
../drivers/usb/phy/phy-fsl-usb.c:865:3: error: '_fsl_readl' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_be;
../drivers/usb/phy/phy-fsl-usb.c:865:16: error: '_fsl_readl_be' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_be;
../drivers/usb/phy/phy-fsl-usb.c:866:3: error: '_fsl_writel' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_be;
../drivers/usb/phy/phy-fsl-usb.c:866:17: error: '_fsl_writel_be' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_be;
../drivers/usb/phy/phy-fsl-usb.c:868:16: error: '_fsl_readl_le' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_le;
../drivers/usb/phy/phy-fsl-usb.c:869:17: error: '_fsl_writel_le' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_le;
and the sysfs "show" function return type should be ssize_t, not int:
The change protects almost the whole body of u_audio_iso_complete()
function by PCM stream lock, this is mainly sufficient to avoid a race
between USB request completion and stream termination, the change
prevents a possibility of invalid memory access in interrupt context
by memcpy():
Also added a check for potential !runtime condition, commonly it is
done by PCM_RUNTIME_CHECK(substream) in the beginning, however this
does not completely prevent from oopses in u_audio_iso_complete(),
because the proper protection scheme must be implemented in PCM
library functions.
An example of *not fixed* oops due to substream->runtime->*
dereference by snd_pcm_running(substream) from
snd_pcm_period_elapsed(), where substream->runtime is gone while
waiting the substream lock:
Unable to handle kernel paging request at virtual address 6b6b6b6b
pgd = db7e4000
[6b6b6b6b] *pgd=00000000
CPU: 0 PID: 193 Comm: klogd Tainted: G C 3.14.54+ #118
task: db5ac500 ti: db60c000 task.ti: db60c000
PC is at snd_pcm_period_elapsed+0x48/0xd8 [snd_pcm]
LR is at snd_pcm_period_elapsed+0x40/0xd8 [snd_pcm]
pc : [<>] lr : [<>] psr: 60000193
Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5387d Table: 2b7e404a DAC: 00000015
Process klogd (pid: 193, stack limit = 0xdb60c238)
[<>] (snd_pcm_period_elapsed [snd_pcm]) from [<>] (udc_irq+0x500/0xbbc)
[<>] (udc_irq) from [<>] (ci_irq+0x280/0x304)
[<>] (ci_irq) from [<>] (handle_irq_event_percpu+0xa4/0x40c)
[<>] (handle_irq_event_percpu) from [<>] (handle_irq_event+0x3c/0x5c)
[<>] (handle_irq_event) from [<>] (handle_fasteoi_irq+0xc4/0x110)
[<>] (handle_fasteoi_irq) from [<>] (generic_handle_irq+0x20/0x30)
[<>] (generic_handle_irq) from [<>] (handle_IRQ+0x80/0xc0)
[<>] (handle_IRQ) from [<>] (gic_handle_irq+0x3c/0x60)
[<>] (gic_handle_irq) from [<>] (__irq_svc+0x44/0x78)
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
[erosca: W/o this patch, with minimal instrumentation [1], I can
consistently reproduce BUG: KASAN: use-after-free [2]]
[1] Instrumentation to reproduce issue [2]:
# diff --git a/drivers/usb/gadget/function/u_audio.c b/drivers/usb/gadget/function/u_audio.c
# index a72295c953bb..bd0b308024fe 100644
# --- a/drivers/usb/gadget/function/u_audio.c
# +++ b/drivers/usb/gadget/function/u_audio.c
# @@ -16,6 +16,7 @@
# #include <sound/core.h>
# #include <sound/pcm.h>
# #include <sound/pcm_params.h>
# +#include <linux/delay.h>
#
# #include "u_audio.h"
#
# @@ -147,6 +148,8 @@ static void u_audio_iso_complete(struct usb_ep *ep, struct usb_request *req)
#
# spin_unlock_irqrestore(&prm->lock, flags);
#
# + udelay(500); //delay here to increase probability of parallel activities
# +
# /* Pack USB load in ALSA ring buffer */
# pending = prm->dma_bytes - hw_ptr;
[2] After applying [1], below BUG occurs on Rcar-H3-Salvator-X board:
==================================================================
BUG: KASAN: use-after-free in u_audio_iso_complete+0x24c/0x520 [u_audio]
Read of size 8 at addr ffff8006cafcc248 by task swapper/0/0
Substream period size potentially can be changed in runtime, however
this is not accounted in the data copying routine, the change replaces
the cached value with an actual value from substream runtime.
As a side effect the change also removes a potential division by zero
in u_audio_iso_complete() function, if there is a race with
uac_pcm_hw_free(), which sets prm->period_size to 0.
Fixes: 132fcb460839 ("usb: gadget: Add Audio Class 2.0 Driver") Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
There is no necessity to copy PCM stream ring buffer area and size
properties to UAC private data structure, these values can be got
from substream itself.
The change gives more control on substream and avoid stale caching.
Fixes: 132fcb460839 ("usb: gadget: Add Audio Class 2.0 Driver") Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In u_audio_iso_complete, the runtime hw_ptr is updated before the
data is actually copied over to/from the buffer/dma area. When
ALSA uses this hw_ptr, the data may not actually be available to
be used. This causes trash/stale audio to play/record. This
patch updates the hw_ptr after the data has been copied to avoid
this.
Fixes: 132fcb460839 ("usb: gadget: Add Audio Class 2.0 Driver") Signed-off-by: Joshua Frkuska <joshua_frkuska@mentor.com> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Fix below smatch (v0.5.0-4443-g69e9094e11c1) warnings:
drivers/usb/gadget/function/u_audio.c:607 g_audio_setup() warn: strcpy() 'pcm_name' of unknown size might be too large for 'pcm->name'
drivers/usb/gadget/function/u_audio.c:614 g_audio_setup() warn: strcpy() 'card_name' of unknown size might be too large for 'card->driver'
drivers/usb/gadget/function/u_audio.c:615 g_audio_setup() warn: strcpy() 'card_name' of unknown size might be too large for 'card->shortname'
Below commits performed a similar 's/strcpy/strlcpy/' rework:
* v2.6.31 commit 8372d4980fbc ("ALSA: ctxfi - Fix PCM device naming")
* v4.14 commit 003d3e70dbeb ("ALSA: ad1848: fix format string overflow warning")
* v4.14 commit 6d8b04de87e1 ("ALSA: cs423x: fix format string overflow warning")
Fixes: eb9fecb9e69b ("usb: gadget: f_uac2: split out audio core") Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If usb_ep_autoconfig() fails (i.e. returns a null endpoint descriptor),
we expect afunc_bind() to fail (i.e. return a negative error code).
However, due to v4.10-rc1 commit f1d3861d63a5 ("usb: gadget: f_uac2: fix
error handling at afunc_bind"), afunc_bind() returns zero, telling the
caller that it succeeded. This then generates NULL pointer dereference
in below scenario on Rcar H3-ES20-Salvator-X target:
After this patch is applied, the issue is fixed:
rcar-gen3:/home/root# modprobe g_audio
[ 59.217127] g_audio gadget: afunc_bind:565 Error!
[ 59.222329] g_audio ee020000.usb: failed to start g_audio: -19
modprobe: ERROR: could not insert 'g_audio': No such device
rcar-gen3:/home/root# modprobe -r g_audio
rcar-gen3:/home/root#
Fixes: f1d3861d63a5 ("usb: gadget: f_uac2: fix error handling at afunc_bind") Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If the server or network is misbehaving and we get an unexpected reply
we can sometimes miss the request not being started and wait on a
request and never get a response, or even double complete the same
request. Fix this by replacing the send_complete completion with just a
per command lock. Add a per command cookie as well so that we can know
if we're getting a double completion for a previous event. Also check
to make sure we dont have REQUEUED set as that means we raced with the
timeout handler and need to just let the retry occur.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
We can race with the snd timeout and the per-request timeout and end up
requeuing the same request twice. We can't use the send_complete
completion to tell if everything is ok because we hold the tx_lock
during send, so the timeout stuff will block waiting to mark the socket
dead, and we could be marked complete and still requeue. Instead add a
flag to the socket so we know whether we've been requeued yet.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The LVDS signal integrity is only guaranteed when the correct enable
sequence (first IPU DI, then LDB) is used. If the LDB display output was
active before the imx-drm driver is loaded (like when a bootsplash was
active) the DI will be disabled by the full IPU reset we do when loading
the driver. The LDB control registers are not part of the IPU range and
thus will remain unchanged.
This leads to the LDB still being active when the DI is getting enabled,
effectively reversing the required enable sequence. Fix this by also
disabling the LDB on driver bind.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Transport drivers allocate memory for iSCSI hdr in alloc_pdu() and assign
it to task->hdr. In case of TMF task->hdr will be NULL resulting in NULL
pointer dereference.
2. ISCSI_OP_SCSI_DATA_OUT - In this case transport driver can free the
memory for iSCSI hdr after transmitting the pdu so task->hdr can be NULL or
invalid.
This patch fixes this issue by removing task->hdr->opcode from the printk
statement.
Signed-off-by: Varun Prakash <varun@chelsio.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The bridge loses its hw state when the cable is unplugged. If we detect
this case in the hpd handler, reset its state.
Reported-by: Rob Clark <robdclark@gmail.com> Tested-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Archit Taneja <architt@codeaurora.org> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20180703165648.120401-1-seanpaul@chromium.org Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
I was looking at usually suppressed gcc warnings,
[-Wimplicit-fallthrough=] in this case:
The code definitely looks like a break is missing here.
However I am not able to test the NL80211_IFTYPE_MESH_POINT,
nor do I actually know what might be :)
So please use this patch with caution and only if you are
able to do some testing.
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
[johannes: looks obvious enough to apply as is, interesting
though that it never seems to have been a problem] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Previously, when an MMP-protected file system is remounted read-only,
the kmmpd thread would exit the next time it woke up (a few seconds
later), without resetting the MMP sequence number back to
EXT4_MMP_SEQ_CLEAN.
Fix this by explicitly killing the MMP thread when the file system is
remounted read-only.
Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: Andreas Dilger <adilger@dilger.ca> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
As part of hw reconfig, only stations linked to AP interfaces are added
back to the driver ignoring those which are tied to AP_VLAN interfaces.
It is true that there could be stations tied to the AP_VLAN interface while
serving 4addr clients or when using AP_VLAN for VLAN operations; we should
be adding these stations back to the driver as part of hw reconfig, failing
to do so can cause functional issues.
In the case of ath10k driver, the following errors were observed.
This ought to be an omission in e6194923237 ("esp: Fix memleaks on error
paths."). The memleak on error path in esp6_input is similar to esp_input
of esp4.
Fixes: e6194923237 ("esp: Fix memleaks on error paths.") Fixes: 3f29770723f ("ipsec: check return value of skb_to_sgvec always") Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Fix missing dst_release() when local broadcast or multicast traffic is
xfrm policy blocked.
For IPv4 this results to dst leak: ip_route_output_flow() allocates
dst_entry via __ip_route_output_key() and passes it to
xfrm_lookup_route(). xfrm_lookup returns ERR_PTR(-EPERM) that is
propagated. The dst that was allocated is never released.
IPv4 local broadcast testcase:
ping -b 192.168.1.255 &
sleep 1
ip xfrm policy add src 0.0.0.0/0 dst 192.168.1.255/32 dir out action block
IPv4 multicast testcase:
ping 224.0.0.1 &
sleep 1
ip xfrm policy add src 0.0.0.0/0 dst 224.0.0.1/32 dir out action block
For IPv6 the missing dst_release() causes trouble e.g. when used in netns:
ip netns add TEST
ip netns exec TEST ip link set lo up
ip link add dummy0 type dummy
ip link set dev dummy0 netns TEST
ip netns exec TEST ip addr add fd00::1111 dev dummy0
ip netns exec TEST ip link set dummy0 up
ip netns exec TEST ping -6 -c 5 ff02::1%dummy0 &
sleep 1
ip netns exec TEST ip xfrm policy add src ::/0 dst ff02::1 dir out action block
wait
ip netns del TEST
After netns deletion we see:
[ 258.239097] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 268.279061] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 278.367018] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 288.375259] unregister_netdevice: waiting for lo to become free. Usage count = 2
Fixes: ac37e2515c1a ("xfrm: release dst_orig in case of error in xfrm_lookup()") Signed-off-by: Tommi Rantala <tommi.t.rantala@nokia.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
mdio_bus: Fix use-after-free on device_register fails
KASAN has found use-after-free in fixed_mdio_bus_init,
commit 0c692d07842a ("drivers/net/phy/mdio_bus.c: call
put_device on device_register() failure") call put_device()
while device_register() fails,give up the last reference
to the device and allow mdiobus_release to be executed
,kfreeing the bus. However in most drives, mdiobus_free
be called to free the bus while mdiobus_register fails.
use-after-free occurs when access bus again, this patch
revert it to let mdiobus_free free the bus.
KASAN report details as below:
BUG: KASAN: use-after-free in mdiobus_free+0x85/0x90 drivers/net/phy/mdio_bus.c:482
Read of size 4 at addr ffff8881dc824d78 by task syz-executor.0/3524
Memory state around the buggy address: ffff8881dc824c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8881dc824c80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8881dc824d00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff8881dc824d80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8881dc824e00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Fixes: 0c692d07842a ("drivers/net/phy/mdio_bus.c: call put_device on device_register() failure") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 6ff7b060535e87c2ae14dd8548512abfdda528fb)
CVE-2019-12819 Signed-off-by: Benjamin M Romer <benjamin.romer@canonical.com> Acked-by: Tyler Hicks <tyhicks@canonical.com> Acked-by: Po-Hsu Lin <po-hsu.lin@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1824690
Downgrade "Unsupported event" message from dev_err to dev_dbg. Otherwise it
floods with this message one some platforms.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
(backported from commit 44c0c23725a16c8803b8809b87651405e8741e4d) Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: You-Sheng Yang <vicamo.yang@canonical.com> Acked-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 26112ddc254c (PCI / ACPI / PM: Resume bridges w/o drivers on
suspend-to-RAM) attempted to fix a functional regression resulting
from commit c62ec4610c40 (PM / core: Fix direct_complete handling
for devices with no callbacks) by resuming PCI bridges without
drivers (that is, "parallel PCI" ones) during system-wide suspend if
the target system state is not ACPI S0 (working state).
That turns out insufficient, however, as it is reported that, at
least in one case, the platform firmware gets confused if a PCIe
root port is suspended before entering the ACPI S3 sleep state.
That issue was exposed by commit 77b3729ca03 (PCI / PM: Use
SMART_SUSPEND and LEAVE_SUSPENDED flags for PCIe ports) that allowed
PCIe ports to stay in runtime suspend during system-wide suspend
(which is OK for suspend-to-idle, but turns out to be problematic
otherwise).
For this reason, drop the driver check from acpi_pci_need_resume()
and resume all bridges (including PCIe ports with drivers) during
system-wide suspend if the target system state is not ACPI S0.
[If the target system state is ACPI S0, it means suspend-to-idle
and the platform firmware is not going to be invoked to actually
suspend the system, so there is no need to resume the bridges in
that case.]
Fixes: 77b3729ca03 (PCI / PM: Use SMART_SUSPEND and LEAVE_SUSPENDED flags for PCIe ports) Link: https://bugzilla.kernel.org/show_bug.cgi?id=200675 Reported-by: teika kazura <teika@gmx.com> Tested-by: teika kazura <teika@gmx.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Cc: 4.16+ <stable@vger.kernel.org> # 4.16+: 26112ddc254c (PCI / ACPI / PM: Resume bridges ...) Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The vm_area_struct is one of the most fundamental memory management
objects, but the management of it is entirely open-coded evertwhere,
ranging from allocation and freeing (using kmem_cache_[z]alloc and
kmem_cache_free) to initializing all the fields.
We want to unify this in order to end up having some unified
initialization of the vmas, and the first step to this is to at least
have basic allocation functions.
Right now those functions are literally just wrappers around the
kmem_cache_*() calls. This is a purely mechanical conversion:
# new vma:
kmem_cache_zalloc(vm_area_cachep, GFP_KERNEL) -> vm_area_alloc()
# copy old vma
kmem_cache_alloc(vm_area_cachep, GFP_KERNEL) -> vm_area_dup(old)
to the point where the old vma passed in to the vm_area_dup() function
isn't even used yet (because I've left all the old manual initialization
alone).
It turned out that pci_remap_iospace() wasn't undone when the driver's
probe failed, and since devm_phy_optional_get() returned -EPROBE_DEFER,
the probe was retried, finally causing the BUG due to trying to remap
already remapped pages.
The V3 Semiconductor PCI driver has the same issue.
Replace devm_pci_remap_iospace() with its devm_ managed version to fix
the bug.
It turned out that pci_remap_iospace() wasn't undone when the driver's
probe failed, and since devm_phy_optional_get() returned -EPROBE_DEFER,
the probe was retried, finally causing the BUG due to trying to remap
already remapped pages.
The MediaTek PCIe driver has the same issue.
Replace devm_pci_remap_iospace() with its devm_ managed counterpart
to fix the bug.
It turned out that pci_remap_iospace() wasn't undone when the driver's
probe failed, and since devm_phy_optional_get() returned -EPROBE_DEFER,
the probe was retried, finally causing the BUG due to trying to remap
already remapped pages.
The Faraday PCI driver has the same issue. Replace pci_remap_iospace()
with its devm_ managed version to fix the bug.
It turned out that pci_remap_iospace() wasn't undone when the driver's
probe failed, and since devm_phy_optional_get() returned -EPROBE_DEFER,
the probe was retried, finally causing the BUG due to trying to remap
already remapped pages.
The Aardvark PCI controller driver has the same issue.
Replace pci_remap_iospace() with its devm_ managed version to fix the bug.
It turned out that pci_remap_iospace() wasn't undone when the driver's
probe failed, and since devm_phy_optional_get() returned -EPROBE_DEFER,
the probe was retried, finally causing the BUG due to trying to remap
already remapped pages.
The DesignWare PCIe controller driver has the same issue.
Replace devm_pci_remap_iospace() with a devm_ managed version to fix the
bug.
Fixes: cbce7900598c ("PCI: designware: Make driver arch-agnostic") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[lorenzo.pieralisi@arm.com: updated the commit log] Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Jingoo Han <jingoohan1@gmail.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
It turned out that pci_remap_iospace() wasn't undone when the driver's
probe failed, and since devm_phy_optional_get() returned -EPROBE_DEFER,
the probe was retried, finally causing the BUG due to trying to remap
already remapped pages.
The X-Gene PCI controller driver has the same issue.
Replace pci_remap_iospace() with the devm_ managed version so that the
pages get unmapped automagically on any probe failure.
During clc handshake the receive timeout is set to CLC_WAIT_TIME.
Remember and reset the original timeout value after the receive calls,
and remove a duplicate assignment of CLC_WAIT_TIME.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
During a device failover, there may be latency between the loss
of the current backing device and a notification from firmware that
a failover has occurred. This latency can result in a large amount of
error printouts as firmware returns outgoing traffic with a generic
error code. These are not necessarily errors in this case as the
firmware is busy swapping in a new backing adapter and is not ready
to send packets yet. This patch reclassifies those error codes as
warnings with an explanation that a failover may be pending. All
other return codes will be considered errors.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 0c3b7e42616f ("tools build: Add support for host programs format")
introduced host_c_flags which referenced CHOSTFLAGS. The actual name of the
variable is HOSTCFLAGS. Fix this up.
Fixes: 0c3b7e42616f ("tools build: Add support for host programs format") Signed-off-by: Laura Abbott <labbott@redhat.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
[Why]
When a dce100 asic was suspended, the clocks were not set to 0.
Upon resume, the new clock was compared to the existing clock,
they were found to be the same, and so the clock was not set.
This resulted in a pernicious blackscreen.
[How]
In atomic commit, check to see if there are any active pipes.
If no, set clocks to 0
Signed-off-by: David Francis <David.Francis@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We fail to correctly clean up after a bus registration failure, which
can lead to an incorrect assumption about the registration state of
the upstream or sfp cage.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Builds started failing in Fedora on Python 3.7 with:
`.gnu.debuglto_.debug_macro' referenced in section
`.gnu.debuglto_.debug_macro' of
util/scripting-engines/trace-event-python.o: defined in discarded
section
In Fedora, Python 3.7 added -flto to the list of --cflags and since it
was only applied to util/scripting-engines/trace-event-python.c and
scripts/python/Perf-Trace-Util/Context.c, linking failed.
It's not the first time the addition of flags has broken builds: commit c6707fdef7e2 ("perf tools: Fix up build in hardnened environments")
appears to have fixed a similar problem. "python-config --includes"
provides the proper -I flags and doesn't introduce additional CFLAGS.
Signed-off-by: Jeremy Cline <jcline@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20180710154612.6285-1-jcline@redhat.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The original complaint was the lsscsi -t showed the same SAS address of the
two enclosures (SEP devices). In fact the SAS address was being set to the
Enclosure Logical Identifier (ELI).
Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Calling bnxt_set_max_func_irqs() to modify the max IRQ count requested or
freed by the RDMA driver is flawed. The max IRQ count is checked when
re-initializing the IRQ vectors and this can happen multiple times
during ifup or ethtool -L. If the max IRQ is reduced and the RDMA
driver is operational, we may not initailize IRQs correctly. This
problem shows up on VFs with very small number of MSIX.
There is no other logic that relies on the IRQ count excluding the ones
used by RDMA. So we fix it by just removing the call to subtract or
add the IRQs used by RDMA.
Fixes: a588e4580a7e ("bnxt_en: Add interface to support RDMA driver.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In case of HSDK we have intermediate INTC in for of DW APB GPIO controller
which is used as a de-bounce logic for interrupt wires that come from
outside the board.
We cannot use existing "irq-dw-apb-ictl" driver here because all input
lines are routed to corresponding output lines but not muxed into one
line (this is configured in RTL and we cannot change this in software).
But even if we add such a feature to "irq-dw-apb-ictl" driver that won't
benefit us as higher-level INTC (in case of HSDK it is IDU) anyways has
per-input control so adding fully-controller intermediate INTC will only
bring some overhead on interrupt processing but no other benefits.
Thus we just do one-time configuration of DW APB GPIO controller and
forget about it.
Based on implementation available on arch/arc/plat-axs10x/axs10x.c file.
Dmitry Osipenko [Sat, 19 May 2018 01:07:10 +0000 (04:07 +0300)]
gpu: host1x: Skip IOMMU initialization if firewall is enabled
BugLink: https://bugs.launchpad.net/bugs/1835845
Host1x's CDMA can't access the command buffers if IOMMU and Host1x
firewall are enabled in the kernels config because firewall doesn't map
the copied buffer into IOVA space. Fix this by skipping IOMMU
initialization if firewall is enabled as firewall merges sparse cmdbufs
into a single contiguous buffer and hence IOMMU isn't needed in this case.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
(backported from commit 4466b1f0e022f94a026bd700fee34bff15cdc4ef) Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Setting the low threshold to 0 has no effect on frags allocation,
we need to clear high_thresh instead.
The code was pre-existent to commit 648700f76b03 ("inet: frags:
use rhashtables for reassembly units"), but before the above,
such assignment had a different role: prevent concurrent eviction
from the worker and the netns cleanup helper.
Fixes: 648700f76b03 ("inet: frags: use rhashtables for reassembly units") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Multiple BPF helpers in use by sk_skb programs calculate the max
skb length using the __bpf_skb_max_len function. However, this
calculates the max length using the skb->dev pointer which can be
NULL when an sk_skb program is paired with an sk_msg program.
To force this a sk_msg program needs to redirect into the ingress
path of a sock with an attach sk_skb program. Then the the sk_skb
program would need to call one of the helpers that adjust the skb
size.
To fix the null ptr dereference use SKB_MAX_ALLOC size if no dev
is available.
t4_get_flash_params() fails in a fatal fashion if the FLASH part isn't
one of the recognized parts. But this leads to desperate efforts to update
drivers when various FLASH parts which we are using suddenly become
unavailable and we need to substitute new FLASH parts. This has lead to
more than one Customer Field Emergency when a Customer has an old driver
and suddenly can't use newly shipped adapters.
This commit fixes this by simply assuming that the FLASH part is 4MB in
size if it can't be identified. Note that all Chelsio adapters will have
flash parts which are at least 4MB in size.
Signed-off-by: Casey Leedom <leedom@chelsio.com> Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
All the control messages broadcast to remote routers are using
QRTR_NODE_BCAST instead of using local router NODE ID which cause
the packets to be dropped on remote router due to invalid NODE ID.
Signed-off-by: Arun Kumar Neelakantam <aneela@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>