Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
(cherry picked from commit dbcf1ca47a2827e8c9fbf7da79cf8ce04fb518ac) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
(cherry picked from commit c799fab722780742eda2a1a79ba09bf83d0e2876) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Ignore: yes Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
(cherry picked from commit e7e2c595b320becf781b8c8caba17ef3278e3bd3) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Seth Forshee [Mon, 26 Jun 2017 17:17:25 +0000 (12:17 -0500)]
UBUNTU: Ubuntu-raspi2-4.11.0-1002.3
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
(cherry picked from commit ec4d22499cbc55cb5237bf802f50a0a9a857bd97) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Seth Forshee [Mon, 26 Jun 2017 17:12:26 +0000 (12:12 -0500)]
UBUNTU: [Config] Add CONFIG_CRASH_DUMP annotation for arm64
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
(cherry picked from commit f7a404cb677df72cf8a7384bc309412c387907a9) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Seth Forshee [Mon, 26 Jun 2017 16:58:18 +0000 (11:58 -0500)]
UBUNTU: Start new release
Ignore: yes Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
(cherry picked from commit 0daa31bbb6e69ee3bc6d1f41071b6af147cbf454) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Seth Forshee [Wed, 21 Jun 2017 16:58:20 +0000 (11:58 -0500)]
UBUNTU: Ubuntu-raspi2-4.11.0-1001.2
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
(cherry picked from commit 13153dd3aeb7c3050c4504a4759169935f2b59f7) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Seth Forshee [Mon, 19 Jun 2017 18:35:02 +0000 (13:35 -0500)]
UBUNTU: Start new release
Ignore: yes Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
(cherry picked from commit 223dcf6eafb28d7096d96e9d1b1e0c4f9eb18119) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Seth Forshee [Tue, 13 Jun 2017 19:06:46 +0000 (14:06 -0500)]
UBUNTU: Ubuntu-raspi2-4.11.0-1000.1
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
(cherry picked from commit 0bd48f673cd697dcbbb27e7980a2a7ce7ee07c83) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Seth Forshee [Tue, 13 Jun 2017 18:06:26 +0000 (13:06 -0500)]
UBUNTU: Add raspi2 packaging
Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
(cherry picked from commit 5ff45568b910a663ceeac25418461ab916d679e2) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Andrei Gherzan [Mon, 5 Jun 2017 15:40:38 +0000 (16:40 +0100)]
dma-bcm2708: Fix module compilation of CONFIG_DMA_BCM2708
bcm2708-dmaengine.c defines functions like bcm_dma_start which are
defined as well in dma-bcm2708.h as inline versions when
CONFIG_DMA_BCM2708 is not defined. This works fine when
CONFIG_DMA_BCM2708 is built in, but when it is selected as module build
fails with redefinition errors because in the build system when
CONFIG_DMA_BCM2708 is selected as module, the macro becomes
CONFIG_DMA_BCM2708_MODULE.
This patch makes the header use CONFIG_DMA_BCM2708_MODULE too when
available.
Matthias Reichl [Sun, 7 May 2017 14:24:57 +0000 (16:24 +0200)]
ASoC: bcm2835: Enforce full symmetry
bcm2835's configuration registers can't be changed when a stream
is running, which means asymmetric configurations aren't supported.
Channel and rate symmetry are already enforced by constraints
but samplebits had been missed.
As hw_params doesn't check for symmetry constraints by itself
and just returns success if a stream is running this led to
situations where asymmetric configurations were seeming to
succeed but of course didn't work because the hardware wasn't
configured at all.
Fix this by adding the missing samplerate symmetry constraint.
Matthias Reichl [Sun, 7 May 2017 13:30:50 +0000 (15:30 +0200)]
ASoC: bcm2835: Support left/right justified and DSP modes
DSP modes and left/right justified modes can be supported
on bcm2835 by configuring the frame sync polarity and
frame sync length registers and by adjusting the
channel data position registers.
Clock and frame sync polarity handling in hw_params has
been refactored to make the interaction between logical
rising/falling edge frame start and physical configuration
(changed by normal/inverted polarity modes) clearer.
Modes where the first active data bit is transmitted immediately
after frame start (eg DSP mode B with slot 0 active)
only work reliable if bcm2835 is configured as frame master.
In frame slave mode channel swap (or shift, this isn't quite
clear yet) can occur.
Currently the driver only warns if an unstable configuration
is detected but doensn't prevent using them.
Matthias Reichl [Sun, 7 May 2017 09:34:26 +0000 (11:34 +0200)]
ASoC: bcm2835: Add support for TDM modes
bcm2835 supports arbitrary positioning of channel data within
a frame and thus is capable of supporting TDM modes. Since
the driver is limited to 2-channel operations only TDM setups
with exactly 2 active slots are supported.
Logical TDM slot numbering follows the usual convention:
For I2S-like modes, with a 50% duty-cycle frame clock,
slots 0, 2, ... are transmitted in the first half of a frame,
slots 1, 3, ... are transmitted in the second half.
For DSP modes slot numbering is ascending: 0, 1, 2, 3, ...
Channel position calculation has been refactored to use
TDM info and moved out of hw_params.
set_tdm_slot, set_bclk_ratio and hw_params now check more
strictly if the configuration is valid. Illegal configurations
like odd number of slots in I2S mode, data lengths exceeding
slot width or frame sizes larger than the hardware limit of
1024 are rejected. Also hw_params now properly checks for
errors from clk_set_rate.
Allowed PCM formats are already guarded by stream constraints,
thus the formats check in hw_params has been removed and
data_length is now retrieved via params_width().
Also standard functions like snd_soc_params_to_bclk are now
being used instead of manual calculations to make the code
more readable.
Special care has been taken to ensure that set_bclk_ratio works
as before. The bclk ratio is mapped to a 2-channel TDM config
with a slot width of half the ratio. In order to support odd ratios,
which can't be expressed via a TDM config, the ratio (frame length)
is stored and used by hw_params.
Eric Anholt [Thu, 2 Feb 2017 17:42:18 +0000 (09:42 -0800)]
drm/vc4: Fix sending of page flip completion events in FKMS mode.
In the rewrite of vc4_crtc.c for fkms, I dropped the part of the
CRTC's atomic flush handler that moved the completion event from the
proposed atomic state change to the CRTC's current state. That meant
that when full screen pageflipping happened (glxgears -fullscreen in
X, compton, por weston), the app would end up blocked firever waiting
to draw its next frame.
This is the driver for Sony CXD2880 DVB-T2/T tuner + demodulator. It includes the CXD2880 driver and the CXD2880 SPI adapter. The current CXD2880 driver version is 1.4.1 - 1.0.1 released on April 13, 2017.
Phil Elwell [Thu, 23 Mar 2017 16:34:46 +0000 (16:34 +0000)]
bcm2835-aux: Add aux interrupt controller
The AUX block has a shared interrupt line with a register indicating
which devices have active IRQs. Expose this as a nested interrupt
controller to avoid sharing problems.
Phil Elwell [Tue, 24 Feb 2015 13:40:50 +0000 (13:40 +0000)]
pinctrl-bcm2835: Fix interrupt handling for GPIOs 28-31 and 46-53
Contrary to the documentation, the BCM2835 GPIO controller actually has
four interrupt lines - one each for the three IRQ groups and one common. Rather
confusingly, the GPIO interrupt groups don't correspond directly with the GPIO
control banks. Instead, GPIOs 0-27 generate IRQ GPIO0, 28-45 GPIO1 and
46-53 GPIO2.
Awkwardly, the GPIOS for IRQ GPIO1 straddle two 32-entry GPIO banks, so it is
cleaner to split out a function to process the interrupts for a single GPIO
bank.
This bug has only just been observed because GPIOs above 27 can only be
accessed on an old Raspberry Pi with the optional P5 header fitted, where
the pins are often used for I2S instead.
Michael Zoran [Sun, 15 Jan 2017 05:43:57 +0000 (21:43 -0800)]
ARM64: Round-Robin dispatch IRQs between CPUs.
IRQ-CPU mapping is round robined on ARM64 to increase
concurrency and allow multiple interrupts to be serviced
at a time. This reduces the need for FIQ.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
Michael Zoran [Sun, 15 Jan 2017 05:33:51 +0000 (21:33 -0800)]
ARM64/DWC_OTG: Port dwc_otg driver to ARM64
In ARM64, the FIQ mechanism used by this driver is not current
implemented. As a workaround, reqular IRQ is used instead
of FIQ.
In a separate change, the IRQ-CPU mapping is round robined
on ARM64 to increase concurrency and allow multiple interrupts
to be serviced at a time. This reduces the need for FIQ.
Tests Run:
This mechanism is most likely to break when multiple USB devices
are attached at the same time. So the system was tested under
stress.
Devices:
1. USB Speakers playing back a FLAC audio through VLC
at 96KHz.(Higher then typically, but supported on my speakers).
2. sftp transferring large files through the buildin ethernet
connection which is connected through USB.
3. Keyboard and mouse attached and being used.
Although I do occasionally hear some glitches, the music seems to
play quite well.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
Michael Zoran [Sun, 15 Jan 2017 15:25:18 +0000 (07:25 -0800)]
ARM64: Fix build break for RTL8187/RTL8192CU wifi
These drivers use an ASM function from the base
system to compute the ipv6 checksum. These functions
are not available on ARM64, probably because nobody
has bother to write them. The base system does have
a generic "C" version, so a simple fix is to include
the header to use the generic version on ARM64 only.
A longer term solution would be to submit the necessary
ASM function to the upstream source.
With this change, these drivers now compile without
any errors on ARM64.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
Electron752 [Sat, 14 Jan 2017 10:54:26 +0000 (02:54 -0800)]
ARM64: Enable Kernel Address Space Randomization (#1792)
Randomization allows the mapping between virtual addresses and physical
address to be different on each boot. This makes it more difficult
to exploit security vulnerabilities that require knowledge of fixed
hardware addresses.
The firmware generates a 8 byte random number during bootup and stores
it in the device tree under chosen/kaslr-seed. This number is used
to randomize the address mapping.
This change enables this feature in the build configuration for ARM64.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
Electron752 [Thu, 12 Jan 2017 15:07:08 +0000 (07:07 -0800)]
ARM64: Make it work again on 4.9 (#1790)
* Invoke the dtc compiler with the same options used in arm mode.
* ARM64 now uses the bcm2835 platform just like ARM32.
* ARM64: Update bcmrpi3_defconfig
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
Michael Zoran [Wed, 24 Aug 2016 10:35:56 +0000 (03:35 -0700)]
Add arm64 configuration and device tree differences. Disable MMC_BCM2835_SDHOST and MMC_BCM2835 since these drivers are crashing at the moment.
ARM64: Modify default config to get raspbian to boot (#1686)
1. Enable emulation of deprecated instructions.
2. Enable ARM 8.1 and 8.2 features which are not detected at runtime.
3. Switch the default governer to powersave.
4. Include the watchdog timer driver in the kernel image rather then a module.
Cheong2K [Fri, 26 Feb 2016 10:20:10 +0000 (18:20 +0800)]
brcm: adds support for BCM43341 wifi
brcmfmac: Disable power management
Disable wireless power saving in the brcmfmac WLAN driver. This is a
temporary measure until the connectivity loss resulting from power
saving is resolved.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: Use original country code as a fallback
brcmfmac: Configure country code using device specific settings
prevents region codes from working on devices that lack a region code
translation table. In the event of an absent table, preserve the old
behaviour of using the provided code as-is.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: Plug memory leak in brcmf_fill_bss_param
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: do not use internal roaming engine by default
Some evidence of curing disconnects with this disabled, so make it a default.
Can be overridden with module parameter roamoff=0
See: http://projectable.me/optimize-my-pi-wi-fi/
brcmfmac: Change stop_ap sequence
Patch from Broadcom/Cypress to resolve a customer error
This is a port of Pantelis Antoniou's v3 port that makes use of the
new upstreamed configfs support for binary attributes.
Original commit message:
Add a runtime interface to using configfs for generic device tree overlay
usage. With it its possible to use device tree overlays without having
to use a per-platform overlay manager.
Please see Documentation/devicetree/configfs-overlays.txt for more info.
Changes since v2:
- Removed ifdef CONFIG_OF_OVERLAY (since for now it's required)
- Created a documentation entry
- Slight rewording in Kconfig
Changes since v1:
- of_resolve() -> of_resolve_phandles().
Originally-signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com> Signed-off-by: Phil Elwell <phil@raspberrypi.org>
DT configfs: Fix build errors on other platforms
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
DT configfs: fix build error
There is an error when compiling rpi-4.6.y branch:
CC drivers/of/configfs.o
drivers/of/configfs.c:291:21: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
.default_groups = of_cfs_def_groups,
^
drivers/of/configfs.c:291:21: note: (near initialization for 'of_cfs_subsys.su_group.default_groups.next')
netdev->priv_destructor() performs all actions to free up the private
resources that used to be freed by netdev->destructor(), except for
free_netdev().
netdev->needs_free_netdev is a boolean that indicates whether
free_netdev() should be done at the end of unregister_netdevice().
Phil Elwell [Wed, 1 Mar 2017 16:07:39 +0000 (16:07 +0000)]
amba_pl011: Round input clock up
The UART clock is initialised to be as close to the requested
frequency as possible without exceeding it. Now that there is a
clock manager that returns the actual frequencies, an expected
48MHz clock is reported as 47999625. If the requested baudrate
== requested clock/16, there is no headroom and the slight
reduction in actual clock rate results in failure.
Detect cases where it looks like a "round" clock was chosen and
adjust the reported clock to match that "round" value. As the
code comment says:
/*
* If increasing a clock by less than 0.1% changes it
* from ..999.. to ..000.., round up.
*/
Phil Elwell [Tue, 23 Feb 2016 17:26:48 +0000 (17:26 +0000)]
amba_pl011: Don't use DT aliases for numbering
The pl011 driver looks for DT aliases of the form "serial<n>",
and if found uses <n> as the device ID. This can cause
/dev/ttyAMA0 to become /dev/ttyAMA1, which is confusing if the
other serial port is provided by the 8250 driver which doesn't
use the same logic.
Dave Stevenson [Mon, 20 Feb 2017 17:01:21 +0000 (17:01 +0000)]
bcm2835-gpio-exp: Driver for GPIO expander via mailbox service
Pi3 and Compute Module 3 have a GPIO expander that the
VPU communicates with.
There is a mailbox service that now allows control of this
expander, so add a kernel driver that can make use of it.
Pwr_led node added to device-tree for Pi3.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
P33M [Wed, 21 Oct 2015 13:55:21 +0000 (14:55 +0100)]
rpi_display: add backlight driver and overlay
Add a mailbox-driven backlight controller for the Raspberry Pi DSI
touchscreen display. Requires updated GPU firmware to recognise the
mailbox request.
Signed-off-by: Gordon Hollingworth <gordon@raspberrypi.org>
This patch adds new sample rates to the Audioinjector Octo sound card. The
new supported rates are (in kHz) :
96, 48, 32, 24, 16, 8, 88.2, 44.1, 29.4, 22.05, 14.7
Reference the bcm270x DT regulators in the overlay.
This patch adds a reset GPIO for the AudioInjector.net octo sound card.
Audioinjector octo : Make the playback and capture symmetric
This patch ensures that the sample rate and channel count of the audioinjector
octo sound card are symmetric.
Fe-Pi [Wed, 1 Mar 2017 11:42:43 +0000 (04:42 -0700)]
Add support for Fe-Pi audio sound card. (#1867)
Fe-Pi Audio Sound Card is based on NXP SGTL5000 codec.
Mechanical specification of the board is the same the Raspberry Pi Zero.
3.5mm jacks for Headphone/Mic, Line In, and Line Out.
gtrainavicius [Sun, 23 Oct 2016 09:06:53 +0000 (12:06 +0300)]
Support for Blokas Labs pisound board
Pisound dynamic overlay (#1760)
Restructuring pisound-overlay.dts, so it can be loaded and unloaded dynamically using dtoverlay.
Print a logline when the kernel module is removed.
pisound improvements:
* Added a writable sysfs object to enable scripts / user space software
to blink MIDI activity LEDs for variable duration.
* Improved hw_param constraints setting.
* Added compatibility with S16_LE sample format.
* Exposed some simple placeholder volume controls, so the card appears
in volumealsa widget.
Add support for Allo Boss DAC add-on board for Raspberry Pi. (#1924)
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net> Reviewed-by: Deepak <deepak@zilogic.com> Reviewed-by: BabuSubashChandar <babusubashchandar@zilogic.com>
Add support for new clock rate and mute gpios.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net> Reviewed-by: Deepak <deepak@zilogic.com> Reviewed-by: BabuSubashChandar <babusubashchandar@zilogic.com>
Raashid Muhammed [Mon, 27 Mar 2017 07:05:00 +0000 (12:35 +0530)]
Add support for Allo Piano DAC 2.1 plus add-on board for Raspberry Pi.
The Piano DAC 2.1 has support for 4 channels with subwoofer.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net> Reviewed-by: Vijay Kumar B. <vijaykumar@zilogic.com> Reviewed-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
Add clock changes and mute gpios (#1938)
Also improve code style and adhere to ALSA coding conventions.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net> Reviewed-by: Vijay Kumar B. <vijaykumar@zilogic.com> Reviewed-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
PianoPlus: Dual Mono & Dual Stereo features added (#2069)
Allo Piano DAC boards: Initial 2 channel (stereo) support (#1645)
Add initial 2 channel (stereo) support for Allo Piano DAC (2.0/2.1) boards,
using allo-piano-dac-pcm512x-audio overlay and allo-piano-dac ALSA ASoC
machine driver.
NB. The initial support is 2 channel (stereo) ONLY!
(The Piano DAC 2.1 will only support 2 channel (stereo) left/right output,
pending an update to the upstream pcm512x codec driver, which will have
to be submitted via upstream. With the initial downstream support,
provided by this patch, the Piano DAC 2.1 subwoofer outputs will
not function.)
Matt Flax [Mon, 16 May 2016 11:36:31 +0000 (21:36 +1000)]
New AudioInjector.net Pi soundcard with low jitter audio in and out.
Contains the sound/soc/bcm ALSA machine driver and necessary alterations to the Kconfig and Makefile.
Adds the dts overlay and updates the Makefile and README.
Updates the relevant defconfig files to enable building for the Raspberry Pi.
Thanks to Phil Elwell (pelwell) for the review, simple-card concepts and discussion. Thanks to Clive Messer for overlay naming suggestions.
Added support for headphones, microphone and bclk_ratio settings.
This patch adds headphone and microphone capability to the Audio Injector sound card. The patch also sets the bit clock ratio for use in the bcm2835-i2s driver. The bcm2835-i2s can't handle an 8 kHz sample rate when the bit clock is at 12 MHz because its register is only 10 bits wide which can't represent the ch2 offset of 1508. For that reason, the rate constraint is added.
ARM: adau1977-adc: Add basic machine driver for adau1977 codec driver.
This commit adds basic support for the codec usage including: Device tree overlay,
binding I2S bus and setting I2S mode, clock source and frequency setting according
to spec.
Forward port of 3.10.x driver from https://github.com/koalo
We are using a custom board and would like to use rpi 3.18.x
kernel. Patch works fine for our embedded system.
URL to the audio chip:
http://www.mikroe.com/add-on-boards/audio-voice/audio-codec-proto/
Added driver for HiFiBerry Amp amplifier add-on board
The driver contains a low-level hardware driver for the TAS5713 and the
drivers for the Raspberry Pi I2S subsystem.
TAS5713: return error if initialisation fails
Existing TAS5713 driver logs errors during initialisation, but does not return
an error code. Therefore even if initialisation fails, the driver will still be
loaded, but won't work. This patch fixes this. I2C communication error will now
reported correctly by a non-zero return code.
HiFiBerry Amp: fix device-tree problems
Some code to load the driver based on device-tree-overlays was missing. This is added by this patch.
The driver is based on the HiFiBerry DAC driver. However HiFiBerry DAC+ uses
a different codec chip (PCM5122), therefore a new driver is necessary.
Add support for the HiFiBerry DAC+ Pro.
The HiFiBerry DAC+ and DAC+ Pro products both use the existing bcm sound driver with the DAC+ Pro having a special clock device driver representing the two high precision oscillators.
An addition bug fix is included for the PCM512x codec where by the physical size of the sample frame is used in the calculation of the LRCK divisor as it was found to be wrong when using 24-bit depth sample contained in a little endian 4-byte sample frame.
Limit PCM512x "Digital" gain to 0dB by default with HiFiBerry DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Add dt param to force HiFiBerry DAC+ Pro into slave mode
"dtoverlay=hifiberry-dacplus,slave"
Add 'slave' param to use HiFiBerry DAC+ Pro in slave mode,
with Pi as master for bit and frame clock.
Gordon Garrity [Sat, 8 Mar 2014 16:56:57 +0000 (16:56 +0000)]
Add IQaudIO Sound Card support for Raspberry Pi
Set a limit of 0dB on Digital Volume Control
The main volume control in the PCM512x DAC has a range up to
+24dB. This is dangerously loud and can potentially cause massive
clipping in the output stages. Therefore this sets a sensible
limit of 0dB for this control.
Allow up to 24dB digital gain to be applied when using IQAudIO DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Modify IQAudIO DAC+ ASoC driver to set card/dai config from dt
Add the ability to set the card name, dai name and dai stream name, from
dt config.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
IQaudIO: auto-mute for AMP+ and DigiAMP+
IQAudIO amplifier mute via GPIO22. Add dt params for "one-shot" unmute
and auto mute.
Revision 2, auto mute implementing HiassofT suggestion to mute/unmute
using set_bias_level, rather than startup/shutdown....
"By default DAPM waits 5 seconds (pmdown_time) before shutting down
playback streams so a close/stop immediately followed by open/start
doesn't trigger an amp mute+unmute."
Tested on both AMP+ (via DAC+) and DigiAMP+, with both options...
dtoverlay=iqaudio-dacplus,unmute_amp
"one-shot" unmute when kernel module loads.
dtoverlay=iqaudio-dacplus,auto_mute_amp
Unmute amp when ALSA device opened by a client. Mute, with 5 second delay
when ALSA device closed. (Re-opening the device within the 5 second close
window, will cancel mute.)
Revision 4, using gpiod.
Revision 5, clean-up formatting before adding mute code.
- Convert tab plus 4 space formatting to 2x tab
- Remove '// NOT USED' commented code
Revision 6, don't attempt to "one-shot" unmute amp, unless card is
successfully registered.
Daniel Matuschek [Wed, 15 Jan 2014 20:42:08 +0000 (21:42 +0100)]
ASoC: BCM:Add support for HiFiBerry Digi. Driver is based on the patched WM8804 driver.
Signed-off-by: Daniel Matuschek <daniel@matuschek.net>
Add a parameter to turn off SPDIF output if no audio is playing
This patch adds the paramater auto_shutdown_output to the kernel module.
Default behaviour of the module is the same, but when auto_shutdown_output
is set to 1, the SPDIF oputput will shutdown if no stream is playing.
bugfix for 32kHz sample rate, was missing
HiFiBerry Digi: set SPDIF status bits for sample rate
The HiFiBerry Digi driver did not signal the sample rate in the SPDIF status bits.
While this is optional, some DACs and receivers do not accept this signal. This patch
adds the sample rate bits in the SPDIF status block.
Added HiFiBerry Digi+ Pro driver
Signed-off-by: Daniel Matuschek <daniel@hifiberry.com>
Daniel Matuschek [Wed, 15 Jan 2014 20:41:23 +0000 (21:41 +0100)]
ASoC: wm8804: Implement MCLK configuration options, add 32bit support WM8804 can run with PLL frequencies of 256xfs and 128xfs for most sample rates. At 192kHz only 128xfs is supported. The existing driver selects 128xfs automatically for some lower samples rates. By using an additional mclk_div divider, it is now possible to control the behaviour. This allows using 256xfs PLL frequency on all sample rates up to 96kHz. It should allow lower jitter and better signal quality. The behavior has to be controlled by the sound card driver, because some sample frequency share the same setting. e.g. 192kHz and 96kHz use 24.576MHz master clock. The only difference is the MCLK divider.
This also added support for 32bit data.
Signed-off-by: Daniel Matuschek <daniel@matuschek.net>
Phil Elwell [Thu, 25 Jun 2015 11:16:11 +0000 (12:16 +0100)]
gpio-poweroff: Allow it to work on Raspberry Pi
The Raspberry Pi firmware manages the power-down and reboot
process. To do this it installs a pm_power_off handler, causing
the gpio-poweroff module to abort the probe function.
This patch introduces a "force" DT property that overrides that
behaviour, and also adds a DT overlay to enable and control it.
Note that running in an active-low configuration (DT parameter
"active_low") requires a custom dt-blob.bin and probably won't
allow a reboot without switching off, so an external inversion
of the trigger signal may be preferable.
Harm Hanemaaijer [Thu, 20 Jun 2013 18:21:39 +0000 (20:21 +0200)]
Speed up console framebuffer imageblit function
Especially on platforms with a slower CPU but a relatively high
framebuffer fill bandwidth, like current ARM devices, the existing
console monochrome imageblit function used to draw console text is
suboptimal for common pixel depths such as 16bpp and 32bpp. The existing
code is quite general and can deal with several pixel depths. By creating
special case functions for 16bpp and 32bpp, by far the most common pixel
formats used on modern systems, a significant speed-up is attained
which can be readily felt on ARM-based devices like the Raspberry Pi
and the Allwinner platform, but should help any platform using the
fb layer.
The special case functions allow constant folding, eliminating a number
of instructions including divide operations, and allow the use of an
unrolled loop, eliminating instructions with a variable shift size,
reducing source memory access instructions, and eliminating excessive
branching. These unrolled loops also allow much better code optimization
by the C compiler. The code that selects which optimized variant is used
is also simplified, eliminating integer divide instructions.
The speed-up, measured by timing 'cat file.txt' in the console, varies
between 40% and 70%, when testing on the Raspberry Pi and Allwinner
ARM-based platforms, depending on font size and the pixel depth, with
the greater benefit for 32bpp.
Phil Elwell [Fri, 6 Feb 2015 13:50:57 +0000 (13:50 +0000)]
BCM270x_DT: Add pwr_led, and the required "input" trigger
The "input" trigger makes the associated GPIO an input. This is to support
the Raspberry Pi PWR LED, which is driven by external hardware in normal use.
N.B. pwr_led is not available on Model A or B boards.
leds-gpio: Implement the brightness_get method
The power LED uses some clever logic that means it is driven
by a voltage measuring circuit when configured as input, otherwise
it is driven by the GPIO output value. This patch wires up the
brightness_get method for leds-gpio so that user-space can monitor
the LED value via /sys/class/gpio/led1/brightness. Using the input
trigger this returns an indication of the system power health,
otherwise it is just whatever value the trigger has written most
recently.
Change DT node named 'axi' to 'soc' so it matches ARCH_BCM2835.
The VC4 bootloader fills in certain properties in the 'axi' subtree,
but since this is part of an upstreaming effort, the name is changed.
Signed-off-by: Noralf Tronnes notro@tronnes.org
BCM2708_DT: Correct length of the peripheral space
Use dts-dirs feature for overlays.
The kernel makefiles have a dts-dirs target that is for vendor subdirectories.
Using this fixes the install_dtbs target, which previously did not install the overlays.
BCM270X_DT: configure I2S DMA channels
Signed-off-by: Matthias Reichl <hias@horus.com>
BCM270X_DT: switch to bcm2835-i2s
I2S soundcard drivers with proper devicetree support (i.e. not linking
to the cpu_dai/platform via name but to cpu/platform via of_node)
will work out of the box without any modifications.
When the kernel is compiled without devicetree support the platform
code will instantiate the bcm2708-i2s driver and I2S soundcard drivers
will link to it via name, as before.
Add paramter to toggle sdio-device-polling
done every second or once at boot-time.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
BCM270X_DT: Make mmc overlay compatible with current firmware
The original DT overlay logic followed a merge-then-patch procedure,
i.e. parameters are applied to the loaded overlay before the overlay
is merged into the base DTB. This sequence has been changed to
patch-then-merge, in order to support parameterised node names, and
to protect against bad overlays. As a result, overrides (parameters)
must only target labels in the overlay, but the overlay can obviously target nodes in the base DTB.
mmc-overlay.dts (that switches back to the original mmc sdcard
driver) is the only overlay violating that rule, and this patch
fixes it.
bcm270x_dt: Use the sdhost MMC controller by default
The "mmc" overlay reverts to using the other controller.
squash: Add cprman to dt
BCM270X_DT: Use clk_core for I2C interfaces
BCM270X_DT: Use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi
The mainline Device Tree files are quite close to downstream now.
Let's use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi as base files
for our dts files.
bcm270x.dtsi contains the downstream bcm283x.dtsi diff.
bcm2708-rpi.dtsi is the downstream version of bcm2835-rpi.dtsi.
Other changes:
- The led node has moved from /soc/leds to /leds. This is not a problem
since the label is used to reference it.
- The clk_osc reg property changes from 6 to 3.
- The gpu nodes has their interrupt property set in the base file.
- the clocks label does not point to the /clocks node anymore, but
points to the cprman node. This is not a problem since the overlays
that use the clock node refer to it directly: target-path = "/clocks";
- some nodes now have 2 labels since mainline and downstream differs in
this respect: cprman/clocks, spi0/spi, gpu/vc4.
- some nodes doesn't have an explicit status = "okay" since they're not
disabled in the base file: watchdog and random.
- gpiomem doesn't need an explicit status = "okay".
- bcm2708-rpi-cm.dts got the hpd-gpios property from bcm2708_common.dtsi,
it's now set directly in that file.
- bcm2709-rpi-2-b.dts has the timer node moved from /soc/timer to /timer.
- Removed clock-frequency property on the bcm{2709,2710}.dtsi timer nodes.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Use raspberrypi-power to turn on USB power
Use the raspberrypi-power driver to turn on USB power.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Add a .dtbo target, use for overlays
Change the filenames and extensions to keep the pre-DDT style of
overlay (<name>-overlay.dtb) distinct from new ones that use a
different style of local fixups (<name>.dtbo), and to match other
platforms.
The RPi firmware uses the DDTK trailer atom to choose which type of
overlay to use for each kernel.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Don't generate "linux,phandle" props
The EPAPR standard says to use "phandle" properties to store phandles,
rather than the deprecated "linux,phandle" version. By default, dtc
generates both, but adding "-H epapr" causes it to only generate
"phandle"s, saving some space and clutter.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add overlay for enc28j60 on SPI2
Works on SPI2 for compute module
BCM270X_DT: Add midi-uart0 overlay
MIDI requires 31.25kbaud, a baudrate unsupported by Linux. The
midi-uart0 overlay configures uart0 (ttyAMA0) to use a fake clock
so that requesting 38.4kbaud actually gets 31.25kbaud.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add i2c-sensor overlay
The i2c-sensor overlay is a container for various pressure and
temperature sensors, currently bmp085 and bmp280. The standalone
bmp085_i2c-sensor overlay is now deprecated.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: overlays/*-overlay.dtb -> overlays/*.dtbo (#1752)
We now create overlays as .dtbo files.
build: support for .dtbo files for dtb overlays
Kernel 4.4.6+ on RaspberryPi support .dtbo files for overlays, instead of .dtb.
Patch the kernel, which has faulty rules to generate .dtbo the way yocto does
Signed-off-by: Herve Jourdain <herve.jourdain@neuf.fr> Signed-off-by: Khem Raj <raj.khem@gmail.com>
BCM270X: Drop position requirement for CMA in VC4 overlay.
No longer necessary since 2aefcd576195a739a7a256099571c9c4a401005f,
and will probably let peeople that want to choose a larger CMA
allocation (particularly on pi0/1).
Signed-off-by: Eric Anholt <eric@anholt.net>
BCM270X_DT: RPi Device Tree tidy
Use the upstream sdhost node, add thermal-zones, and factor out some
common elements.
Phil Elwell [Mon, 11 May 2015 08:00:42 +0000 (09:00 +0100)]
scripts: Add mkknlimg and knlinfo scripts from tools repo
The Raspberry Pi firmware looks for a trailer on the kernel image to
determine whether it was compiled with Device Tree support enabled.
If the firmware finds a kernel without this trailer, or which has a
trailer indicating that it isn't DT-capable, it disables DT support
and reverts to using ATAGs.
The mkknlimg utility adds that trailer, having first analysed the
image to look for signs of DT support and the kernel version string.
knlinfo displays the contents of the trailer in the given kernel image.
scripts/mkknlimg: Add support for ARCH_BCM2835
Add a new trailer field indicating whether this is an ARCH_BCM2835
build, as opposed to MACH_BCM2708/9. If the loader finds this flag
is set it changes the default base dtb file name from bcm270x...
to bcm283y...
Also update knlinfo to show the status of the field.
scripts/mkknlimg: Improve ARCH_BCM2835 detection
The board support code contains sufficient strings to be able to
distinguish 2708 vs. 2835 builds, so remove the check for
bcm2835-pm-wdt which could exist in either.
Also, since the canned configuration is no longer built in (it's
a module), remove the config string checking.
scripts: Multi-platform support for mkknlimg and knlinfo
The firmware uses tags in the kernel trailer to choose which dtb file
to load. Current firmware loads bcm2835-*.dtb if the '283x' tag is true,
otherwise it loads bcm270*.dtb. This scheme breaks if an image supports
multiple platforms.
This patch adds '270X' and '283X' tags to indicate support for RPi and
upstream platforms, respectively. '283x' (note lower case 'x') is left
for old firmware, and is only set if the image only supports upstream
builds.
scripts/mkknlimg: Append a trailer for all input
Now that the firmware assumes an unsigned kernel is DT-capable, it is
helpful to be able to mark a kernel as being non-DT-capable.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
scripts/knlinfo: Decode DDTK atom
Show the DDTK atom as being a boolean.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mkknlimg: Retain downstream-kernel detection
With the death of ARCH_BCM2708 and ARCH_BCM2709, a new way is needed to
determine if this is a "downstream" build that wants the firmware to
load a bcm27xx .dtb. The vc_cma driver is used downstream but not
upstream, making vc_cma_init a suitable predicate symbol.
popcornmix [Wed, 17 Jun 2015 14:44:08 +0000 (15:44 +0100)]
Add Chris Boot's i2c driver
i2c-bcm2708: fixed baudrate
Fixed issue where the wrong CDIV value was set for baudrates below 3815 Hz (for 250MHz bus clock).
In that case the computed CDIV value was more than 0xffff. However the CDIV register width is only 16 bits.
This resulted in incorrect setting of CDIV and higher baudrate than intended.
Example: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0x1704 -> 42430Hz
After correction: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0xffff -> 3815Hz
The correct baudrate is shown in the log after the cdiv > 0xffff correction.
Perform I2C combined transactions when possible
Perform I2C combined transactions whenever possible, within the
restrictions of the Broadcomm Serial Controller.
Disable DONE interrupt during TA poll
Prevent interrupt from being triggered if poll is missed and transfer
starts and finishes.
i2c: Make combined transactions optional and disabled by default
i2c: bcm2708: add device tree support
Add DT support to driver and add to .dtsi file.
Setup pins in .dts file.
i2c is disabled by default.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
bcm2708: don't register i2c controllers when using DT
The devices for the i2c controllers are in the Device Tree.
Only register devices when not using DT.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
I2C: Only register the I2C device for the current board revision
i2c_bcm2708: Fix clock reference counting
Fix grabbing lock from atomic context in i2c driver
2 main changes:
- check for timeouts in the bcm2708_bsc_setup function as indicated by this comment:
/* poll for transfer start bit (should only take 1-20 polls) */
This implies that the setup function can now fail so account for this everywhere it's called
- Removed the clk_get_rate call from inside the setup function as it locks a mutex and that's not ok since we call it from under a spin lock.
i2c-bcm2708: When using DT, leave the GPIO setup to pinctrl
i2c-bcm2708: Increase timeouts to allow larger transfers
Use the timeout value provided by the I2C_TIMEOUT ioctl when waiting
for completion. The default timeout is 1 second.
The third I2C bus (I2C2) is normally reserved for HDMI use. Careless
use of this bus can break an attached display - use with caution.
It is recommended to disable accesses by VideoCore by setting
hdmi_ignore_edid=1 or hdmi_edid_file=1 in config.txt.
The interface is disabled by default - enable using the
i2c2_iknowwhatimdoing DT parameter.
bcm2708-spi: Don't use static pin configuration with DT
Also remove superfluous error checking - the SPI framework ensures the
validity of the chip_select value.
i2c-bcm2708: Remove non-DT support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Set the BSC_CLKT clock streching timeout to 35ms as per SMBus specs.
Fixes i2c_bcm2708: Write to FIFO correctly - v2 (#1574)
* i2c: fix i2c_bcm2708: Clear FIFO before sending data
Make sure FIFO gets cleared before trying to send
data in case of a repeated start (COMBINED=Y).
* i2c: fix i2c_bcm2708: Only write to FIFO when not full
Check if FIFO can accept data before writing.
To avoid a peripheral read on the last iteration of a loop,
both bcm2708_bsc_fifo_fill and ~drain are changed as well.
Aron Szabo [Sat, 16 Jun 2012 10:15:55 +0000 (12:15 +0200)]
lirc: added support for RaspberryPi GPIO
lirc_rpi: Use read_current_timer to determine transmitter delay. Thanks to jjmz and others
See: https://github.com/raspberrypi/linux/issues/525
lirc: Remove restriction on gpio pins that can be used with lirc
Compute Module, for example could use different pins
lirc_rpi: Add parameter to specify input pin pull
Depending on the connected IR circuitry it might be desirable to change the
gpios internal pull from it pull-down default behaviour. Add a module
parameter to allow the user to set it explicitly.
Signed-off-by: Julian Scheel <julian@jusst.de>
lirc-rpi: Use the higher-level irq control functions
This module used to access the irq_chip methods of the
gpio controller directly, rather than going through the
standard enable_irq/irq_set_irq_type functions. This
caused problems on pinctrl-bcm2835 which only implements
the irq_enable/disable methods and not irq_unmask/mask.
lirc-rpi: Correct the interrupt usage
1) Correct the use of enable_irq (i.e. don't call it so often)
2) Correct the shutdown sequence.
3) Avoid a bcm2708_gpio driver quirk by setting the irq flags earlier
lirc-rpi: use getnstimeofday instead of read_current_timer
read_current_timer isn't guaranteed to return values in
microseconds, and indeed it doesn't on a Pi2.
Issue: linux#827
lirc-rpi: Add device tree support, and a suitable overlay
The overlay supports DT parameters that match the old module
parameters, except that gpio_in_pull should be set using the
strings "up", "down" or "off".
lirc-rpi: Also support pinctrl-bcm2835 in non-DT mode
fix auto-sense in lirc_rpi driver
On a Raspberry Pi 2, the lirc_rpi driver might receive spurious
interrupts and change it's low-active / high-active setting.
When this happens, the IR remote control stops working.
This patch disables this auto-detection if the 'sense' parameter
was set in the device tree, making the driver robust to such
spurious interrupts.
Tim Gover [Tue, 22 Jul 2014 14:41:04 +0000 (15:41 +0100)]
vcsm: VideoCore shared memory service for BCM2835
Add experimental support for the VideoCore shared memory service.
This allows user processes to allocate memory from VideoCore's
GPU relocatable heap and mmap the buffers. Additionally, the memory
handles can passed to other VideoCore services such as MMAL, OpenMax
and DispmanX
TODO
* This driver was originally released for BCM28155 which has a different
cache architecture to BCM2835. Consequently, in this release only
uncached mappings are supported. However, there's no fundamental
reason which cached mappings cannot be support or BCM2835
* More refactoring is required to remove the typedefs.
* Re-enable the some of the commented out debug-fs statistics which were
disabled when migrating code from proc-fs.
* There's a lot of code to support sharing of VCSM in order to support
Android. This could probably done more cleanly or perhaps just
removed.
Signed-off-by: Tim Gover <timgover@gmail.com>
config: Disable VC_SM for now to fix hang with cutdown kernel
vcsm: Use boolean as it cannot be built as module
On building the bcm_vc_sm as a module we get the following error:
v7_dma_flush_range and do_munmap are undefined in vc-sm.ko.
Fix by making it not an option to build as module
vcsm: Add ioctl for custom cache flushing
vc-sm: Move headers out of arch directory
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
vcsm: Treat EBUSY as success rather than SIGBUS
Currently if two cores access the same page concurrently one will return VM_FAULT_NOPAGE
and the other VM_FAULT_SIGBUS crashing the user code.
Also report when mapping fails.
Signed-off-by: popcornmix <popcornmix@gmail.com>
vcsm: Provide new ioctl to clean/invalidate a 2D block
vcsm: Convert to loading via device tree.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
VCSM: New option to import a DMABUF for VPU use
Takes a dmabuf, and then calls over to the VPU to wrap
it into a suitable handle.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Phil Elwell [Wed, 25 Mar 2015 17:49:47 +0000 (17:49 +0000)]
Adding bcm2835-sdhost driver, and an overlay to enable it
BCM2835 has two SD card interfaces. This driver uses the other one.
bcm2835-sdhost: Error handling fix, and code clarification
bcm2835-sdhost: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the sdhost interface is restricted to integer divisions of
core_freq, and the highest sensible option for a core_freq of 250MHz
is 84 (250/3 = 83.3MHz), the next being 125 (250/2) which is much too
high.
Use at your own risk.
bcm2835-sdhost: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
bcm2835-sdhost: Improve error handling and recovery
1) Expose the hw_reset method to the MMC framework, removing many
internal calls by the driver.
2) Reduce overclock setting on error.
3) Increase timeout to cope with high capacity cards.
4) Add properties and parameters to control pio_limit and debug.
5) Reduce messages at probe time.
bcm2835-sdhost: Further improve overclock back-off
It seems that the sdhost interface returns CRC7 errors for CMD1,
which is the MMC-specific SEND_OP_COND. Returning these errors to
the MMC layer causes a downward spiral, but ignoring them seems
to be harmless.
The bcm2835-mmc driver (and -sdhost driver that copied from it)
contains code to handle SDIO interrupts in a threaded interrupt
handler rather than waking the MMC framework thread. The change
follows a patch from Russell King that adds the facility as the
preferred way of working.
However, the new code path is only present in ARCH_BCM2835
builds, which I have taken to be a way of testing the waters
rather than making the change across the board; I can't see
any technical reason why it wouldn't be enabled for MACH_BCM270X
builds. So this patch standardises on the ARCH_BCM2835 code,
removing the old code paths.
The MMC card-discovery process generates timeouts. This is
expected behaviour, so reporting it to the user serves no purpose.
Suppress the reporting of timeout errors unless the debug flag
is on.
bcm2835-sdhost: Add workaround for odd behaviour on some cards
For reasons not understood, the sdhost driver fails when reading
sectors very near the end of some SD cards. The problem could
be related to the similar issue that reading the final sector
of any card as part of a multiple read never completes, and the
workaround is an extension of the mechanism introduced to solve
that problem which ensures those sectors are always read singly.
bcm2835-sdhost: Major revision
This is a significant revision of the bcm2835-sdhost driver. It
improves on the original in a number of ways:
1) Through the use of CMD23 for reads it appears to avoid problems
reading some sectors on certain high speed cards.
2) Better atomicity to prevent crashes.
3) Higher performance.
4) Activity logging included, for easier diagnosis in the event
of a problem.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Restore ATOMIC flag to PIO sg mapping
Allocation problems have been seen in a wireless driver, and
this is the only change which might have been responsible.
SQUASH: bcm2835-sdhost: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-sdhost driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Workaround for "slow" sectors
Some cards have been seen to cause timeouts after certain sectors are
read. This workaround enforces a minimum delay between the stop after
reading one of those sectors and a subsequent data command.
Using CMD23 (SET_BLOCK_COUNT) avoids this problem, so good cards will
not be penalised by this workaround.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Firmware manages the clock divisor
The bcm2835-sdhost driver hands control of the CDIV clock divisor
register to matching firmware, allowing it to adjust to a changing
core clock. This removes the need to use the performance governor or
to enable io_is_busy on the on-demand governor in order to get the
best SD performance.
N.B. As SD clocks must be an integer divisor of the core clock, it is
possible that the SD clock for "turbo" mode can be different (even
lower) than "normal" mode.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Reset the clock in task context
Since reprogramming the clock can now involve a round-trip to the
firmware it must not be done at atomic context, and a tasklet
is not a task.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Don't exit cmd wait loop on error
The FAIL flag can be set in the CMD register before command processing
is complete, leading to spurious "failed to complete" errors. This has
the effect of promoting harmless CRC7 errors during CMD1 processing
into errors that can delay and even prevent booting.
Also:
1) Convert the last KERN_ERROR message in the register dumping to
KERN_INFO.
2) Remove an unnecessary reset call from bcm2835_sdhost_add_host.
projects / mirror_ubuntu-artful-kernel.git / log